Hitachi CR 13VB Instruction Manual And Safety Instructions

Marque: Hitachi

Modèle: CR 13VB

Catégorie: Outils électroportatifs

Taper: Instruction Manual And Safety Instructions

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE

AVERTISSEMENT

Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la mort ou

de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce

produit. Prière de lire et de comprendre ce mode d’emploi avant d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs avant qu’ils

utilisent l’outil motorisé.

INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS

WARNING

Improper and unsafe use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and

understand this manual before operating the power tool. Please keep this manual

available for others before they use the power tool.

MANUAL DE INSTRUCCIONES E INSTRUCCIONES DE SEGURIDAD

ADVERTENCIA

¡La utilización inapropiada e insegura de esta herramienta eléctrica puede resultar en

lesiones serias o en la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual antes de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de que utilicen la herramienta eléctrica.

Model Reciprocating Saw

Modèle Scie alternative

Modelo Sierra reciprocante

CR 13VB

IMPORTANT INFORMATION ............................... 3

MEANINGS OF SIGNAL WORDS ........................ 3

SAFETY ...................................................................... 4

GENERAL SAFETY RULES ................................... 4

SPECIFIC SAFETY RULES AND SYMBOLS ......... 5

DOUBLE INSULATION FOR SAFER

OPERATION ................................................... 6

FUNCTIONAL DESCRIPTION .................................... 7

NAME OF PARTS .................................................. 7

SPECIFICATIONS .................................................. 8

ASSEMBLY AND OPERATION ................................. 8

APPLICATIONS ..................................................... 8

PRIOR TO OPERATION ......................................... 8

HOW TO USE THE RECIPROCATING SAW ...... 13

MAINTENANCE AND INSPECTION ....................... 16

ACCESSORIES ......................................................... 17

STANDARD ACCESSORIES ............................... 17

OPTIONAL ACCESSORIES ................................. 18

PARTS LIST .............................................................. 53

CONTENTS

English

Page Page

INFORMATIONS IMPORTANTES ...................... 19

SIGNIFICATION DES MOTS

D’AVERTISSEMENT .................................... 19

SECURITE ................................................................ 20

REGLES GENERALE DE SECURITE ................... 20

REGLES DE SECURITE SPECIFIQUES ET

SYMBOLES .................................................. 21

DOUBLE ISOLATION POUR UN

FONCTIONNEMENT PLUS SUR ................. 23

DESCRIPTION FONCTIONNELLE ........................... 24

NOM DES PARTIES ............................................ 24

SPECIFICATIONS ................................................ 24

ASSEMBLAGE ET FONCTIONNEMENT ................ 25

APPLICATIONS ................................................... 25

AVANT L’UTILISATION ...................................... 25

COMMENT UTILISER LA SCIE

ALTERNATIVE .............................................. 30

ENTRETIEN ET INSPECTION .................................. 33

ACCESSOIRES ......................................................... 34

ACCESSOIRES STANDARD ............................... 34

ACCESSOIRES SUR OPTION ............................. 35

LISTA DES PIÈCES .................................................. 53

TABLE DES MATIERES

Français

Page Page

INFORMACIÓN IMPORTANTE ........................... 36

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN ............................................ 36

SEGURIDAD ............................................................. 37

NORMAS GENERALES DE SEGURIDAD........... 37

NORMAS Y SÍMBOLOS

ESPECÍFICOS DE SEGURIDAD ................... 38

AISLAMIENTO DOBLE PARA OFRECER

UNA OPERACIÓN MÁS SEGURA .............. 39

DESCRIPCIÓN FUNCTIONAL ................................. 41

NOMENCLATURA ............................................... 41

ESPECIFICACIONES ............................................ 41

MONTAJE Y OPERACIÓN ...................................... 42

APLICACIONES ................................................... 42

ANTES DE LA OPERACIÓN ................................ 42

COMO USAR LA SIERRA RECIPROCANTE ....... 47

MANTENIMIENTO E INSPECCIÓN ........................ 50

ACCESORIOS ........................................................... 51

ACCESORIOS ESTÁNDAR ................................. 51

ACCESORIOS OPCIONALES .............................. 52

LISTA DE PIEZAS ................................................... 53

ÍNDICE

Español

Página Página

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual

and in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by

HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in

death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in

minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

English

SAFETY

GENERAL SAFETY RULES

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric shock,

fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit.

Cluttered benches and dark areas invite

accidents.

(2) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power

tools create sparks which may ignite the

dust of fumes.

(3) Keep bystanders children, and visitors

away while operating a power tool.

Distractions can cause you to lose

control.

2. Electrical Safety

(1) Double Insulated tools are equipped with

a polarized plug (one blade is wider than

the other.) This plug will fit in a polarized

outlet only one way. If the plug does not

fit fully in the outlet, reverse the plug. If

it still does not fit, contact a qualified

electrician to install a polarized outlet.

Do not change the plug in any way.

Double Insulation

eliminates the need

for the three wire grounded power cord

and grounded power supply system.

(2) Avoid body contact with grounded

surfaces such as pipes, radiators, ranges

and refrigerators. There is an increased

risk of electric shock if your body is

grounded.

(3) Do not expose power tools to rain or wet

conditions. Water entering a power tool

will increase the risk of electric shock.

(4) Do not abuse the cord. Never use the

cord to carry the tools or pull the plug

from a receptacle. Keep cord away from

heat, oil, sharp edges or moving parts.

Replace damaged cords immediately.

Damaged cords increase the risk of electric

shock.

(5) When operating a power tool outside,

use an outdoor extension cord marked

“W-A” or “W”. These cords are rated for

outdoor use and reduce the risk of

electric shock.

3. Personal Safety

(1) Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use tool while

tires or under the influence of drugs,

alcohol, or medication. A moment of

inattention while operating power tools

may result in serious personal injury.

(2) Dress properly. Do not wear loose

clothing or jewelry. Contain long hair.

Keep your hair, clothing and gloves away

from moving parts. Loose clothes,

jewelry, or long hair can be caught in

moving parts.

(3) Avoid accidental starting. Be sure switch

is off before plugging in. Carrying tools

with your finger on the switch or

plugging in tools that have the switch on

invites accidents.

(4) Remove adjusting keys or wrenches

before turning the tool on. A wrench or

a key that is left attached to a rotating

part of the tool may result in personal

injury.

(5) Do not overreach. Keep proper footing

and balance at all times. Proper footing

and balance enables better control of the

tool in unexpected situations.

(6) Use safety equipment. Always wear eye

protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection

must be used for appropriate conditions.

English

4. Tool Use and Care

(1) Use clamps or other practical way to

secure and support the workpiece to a

stable platform. Holding the work by

hand or against your body is unstable

and may lead to loss of control.

(2) Do not force tool. Use the correct tool

for your application. The correct tool will

do the job better and safer at the rate for

which it is designed.

(3) Do not use tool if switch does not turn it

on or off. Any tool that cannot be

controlled with the switch is dangerous

and must be repaired.

(4) Disconnect the plug form the power

source before making any adjustments,

changing accessories, or storing the tool.

Such preventive safety measures reduce

the risk of starting the tool accidentally.

(5) Store idle tools out of reach of children

and other untrained persons. Tools are

dangerous in the hands of untrained

users.

(6) Maintain tools with care. Keep cutting

tools sharp and clean. Properly

maintained tools, with sharp cutting

edges are less likely to bind and are

easier to control.

(7) Check for misalignment or binding of

moving parts, breakage of parts, and any

other condition that may affect the tool's

operation. If damaged, have the tool

serviced before using. Many accidents

are caused by poorly maintained tools.

(8) Use only accessories that are recommended

by the manufacturer for your model.

Accessories that may be suitable for one

tool, may become hazardous when used

with another tool.

5. Service

(1) Tool service must be performed only by

qualified repair personnel. Service or

maintenance performed by unqualified

personnel could result in a risk of injury.

(2) When servicing a tool, use only identical

replacement parts. Follow instructions

in the Maintenance section of this

manual. Use of unauthorized parts or

failure to follow Maintenance Instruction

may create a risk of electric shock or

injury.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping

surfaces when performing an operation

where the cutting tool may contact

hidden wiring or its own cord. Contact

with a “live” wire will make exposed

metal parts of the tool “live” and shock

the operator.

2. ALWAYS wear ear protectors when

using the tool for extended periods.

Prolonged exposure to high

intensity noise can cause

hearing loss.

3. NEVER touch moving parts.

NEVER place your hands, fingers or

other body parts near the tool’s moving

parts.

4. NEVER operate without all guards in

place.

NEVER operate this tool without all

guards or safety features in place and

in proper working order. If maintenance

or servicing requires the removal of a

guard or safety feature, be sure to

replace the guard or safety feature

before resuming operation of the tool.

5. Use right tool.

Don’t force small tool or attachment to

do the job of a heavy-duty tool.

Don’t use tool for purpose not intended

—for example— don’t use circular saw

for cutting tree limbs or logs.

6. NEVER use a power tool for applications

other than those specified.

NEVER use a power tool for applications

other than those specified in the

Instruction Manual.

7. Handle tool correctly.

Operate the tool according to the

instructions provided herein. Do not

drop or throw the tool. NEVER allow the

tool to be operated by

children,individuals unfamiliar with its

operation or unauthorized personnel.

8. Keep all screws, bolts and covers tightly

in place.

Keep all screws, bolts, and plates tightly

mounted. Check their condition periodically.

9. Do not use power tools if the plastic

housing or handle is cracked.

English

Cracks in the tool’s housing or handle

can lead to electric shock. Such tools

should not be used until repaired.

10. Blades and accessories must be

securely mounted to the tool.

Prevent potential injuries to yourself or

others. Blades, cutting implements and

accessories which have been mounted

to the tool should be secure and tight.

11. Keep motor air vent clean.

The tool’s motor air vent must be kept

clean so that air can freely flow at all

times. Check for dust build-up frequently.

12. Operate power tools at the rated

voltage.

Operate the power tool at voltages

specified on its nameplate.

If using the power tool at a higher

voltage than the rated voltage, it will

result in abnormally fast motor

revolution and may damage the unit and

the motor may burn out.

13. NEVER use a tool which is defective or

operating abnormally.

If the tool appears to be operating

unusually, making strange noises, or

otherwise appears defective, stop using

it immediately and arrange for repairs

by a Hitachi authorized service center.

14. NEVER leave tool running unattended.

Turn power off.

Don’t leave tool until it comes to a

complete stop.

15. Carefully handle power tools.

Should a power tool be dropped or

struck against hard materials

inadvertently, it may be deformed,

cracked, or damaged.

16. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner

benzine, carbon tetrachloride, and

alcohol may damage and crack plastic

parts. Do not wipe them with such

solvents.

Wipe plastic parts with a soft cloth lightly

dampened with soapy water and dry

thoroughly.

17. ALWAYS wear eye protection that meets

the requirement of the latest

revision of ANSI Standard

Z87.1.

18. ALWAYS be careful with buried object

such as an underground wiring.

Touching live wiring or electric cable

with this tool may result in electric

shock.

Confirm before use whether hidden

objects are present, such as electric

cables within the wall, floor or ceiling.

19. Definitions for symbols used on this tool

V ............. volts

Hz ........... hertz

A ............. amperes

o ............ no load speed

W ............ watt

............ Class II Construction

---/min .... revolutions or recipocation per

minute

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool,

HITACHI has adopted a double insulation

design. “Double insulation” means that two

physically separated insulation systems

have been used to insulate the electrically

conductive materials connected to the

power supply from the outer frame handled

by the operator. Therefore, either the symbol

“

” or the words “Double insulation”

appear on the power tool or on the

nameplate.

Although this system has no external

grounding, you must still follow the normal

electrical safety precautions given in this

Instruction Manual, including not using the

power tool in wet environments.

To keep the double insulation system

effective, follow these precautions:

䡬 Only Hitachi Authorized Service Center

should disassemble or assemble this

power tool, and only genuine HITACHI

replacement parts should be installed.

䡬 Clean the exterior of the power tool only

with a soft cloth moistened with soapy

water, and dry thoroughly.

Never use solvents, gasoline or thinners

on plastic components; otherwise the

plastic may dissolve.

English

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

FUNCTIONAL DESCRIPTION

NOTE: The information contained in this Instruction Manual is designed to assist you in

the safe operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read

and understood all safey instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that

differ from those on your own power tool

NAME OF PARTS

Fig. 1

Front cover

Lever

Blade holder

Brush cap

Switch trigger

Housing

Handle

Blade

Base

Rubber cap

Base lever

Dial

Push button

Change lever

English

Motor Single-Phase, Series Commutator Motor

Power Source Single-Phase, 120 V AC 60 Hz

Current 11 A

Capacity Mild Steel Pipe: O.D. 5" (130 mm)

Vinyl Chloride Pipe: O.D. 5" (130 mm)

Wood: Depth 5" (130 mm)

No-Load Speed 0 – 2,800/min.

Stroke 1-1/4" (32 mm)

Weight (without cord) 8.8 lbs (4 kg)

SPECIFICATIONS

ASSEMBLY AND OPERATION

APPLICATIONS

䡬 Cutting metal and stainless steel pipe.

䡬 Cutting various lumber.

䡬 Cutting mild steel, aluminum and

copper plate.

䡬 Cutting synthetic resins, such as phenol

resin and vinyl chloride.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be

utilized conforms to the power source

requirements specified on the product

nameplate.

2. Power switch

Ensure that the switch is in the OFF

position. If the plug is connected to a

receptacle while the switch is in the ON

position, the power tool will start

operating immediately and can cause

serious injury.

3. Extension cord

When the work area is far away from the

power source, use an extension cord of

sufficient thickness and rated capacity.

The extension cord should be kept as

short as practicable.

WARNING:

Damaged cord must be

replaced or repaired.

4. Check the receptacle

If the receptacle only loosely accepts the

plug, the receptacle must be repaired.

Contact a licensed electrician to make

appropriate repairs.

If such a fautly receptacle is used, it may

cause overheating, resulting in a serious

hazard.

5. Confirming condition of the

environment:

Confirm that the work site is placed under

appropriate conditions conforming to

prescribed precautions.

6. Mounting the blade

This unit employs a detachable

mechanism that enables mounting and

removal of saw blades without the use

of a wrench or other tools.

(1) Turn on and off the switching trigger

several times so that the lever can

jump out of the front cover

completely. Thereafter, turn off the

switch and unplug the power cord.

(Fig. 2)

English

CAUTION:

Be absolutely sure to keep the

switch turned off and the power

cord unplugged to prevent any

accident.

(2) Push the lever in the direction of the

arrow mark shown in Fig. 3 marked

on the lever.

(3) Insert the saw blade all the way into

the small slit of the plunger tip with

the lever pushing. You can mount

this blade either in the upward or

downward direction. (Fig. 4, Fig. 5)

(4) When you release the lever, the

spring force will return the lever to

the correct position automatically.

(Fig. 6)

(5) Pull the back of the saw blade two

or three times by hand and check

that the blade is securely mounted.

When pulling the blade, you will

know it is properly mounted if it

clicks and the lever moves slightly.

(Fig. 7)

Lever

Front cover

Fig. 2

Lever

Fig. 3

Blade

Fig. 5

Slit of plunger

Lever

Fig. 6

Fig. 7

Blade

Lever

Fig. 4

Slit of plunger

Blade

English

CAUTION:

When pulling the saw blade, be

absolutely sure to pull it from the

back. Pulling other parts of the

blade will result in an injury.

7. Dismounting the blade

(1) Turn on and off the switching trigger

several times so that the lever can

jump out of the front cover

completely. Thereafter, turn off the

switch and unplug the power cord.

(Fig. 2)

CAUTION:

Be absolutely sure to keep the switch

turned off and the power cord

unplugged to prevent any accident.

(2) After you have pushed the lever in

the direction of the arrow mark

shown in Fig. 3, turn the blade so it

faces downward. The blade should

fall out by itself. If the blade doesn’t

fall out, pull it out by hand.

CAUTION:

Never touch the saw blade

immediately after use. The metal is

hot and can easily burn your skin.

WHEN THE BLADE IS BROKEN

Even when the saw blade is broken and

remains inside the small slit of the

plunger, it should fall out if you push the

lever in the direction of the arrow mark,

and face the blade downward. If it doesn’t

fall out itself, take it out using the

procedures explained below.

(1) If a part of the broken saw blade is

sticking out of the small slit of the

plunger, pull out the protruding part

and take the blade out.

(2) If the broken saw blade is hidden

inside the small slit, hook the broken

blade using a tip of another saw

blade and take it out. (Fig. 8)

MAINTENANCE AND INSPECTION

OF SAW BLADE MOUNT

(1) After use, blow away sawdust, earth,

sand, moisture, etc., with air or brush

them away with a brush, etc., to ensure

that the blade mount can function

smoothly.

(2) As shown in Fig. 9, carry out lubrication

around the blade holder on a periodic

basis by use of cutting fluid, etc.

NOTE:

Continued use of the tool without

cleaning and lubricating the area

where the saw blade is installed can

result in some slack movement of

the lever due to accumulated

sawdust and chips. Under the

circumstances, pull a rubber cap

provided on the lever in the

direction of an arrow mark as shown

in Fig. 10 and remove the rubber cap

from the lever. Then, clean up the

inside of the blade holder with air

and the like and carry out sufficient

lubrication.

The rubber cap can be fitted on if it

Another blade

Fig. 8

Lever

Slit of plunger

Blade holder

Machine oil

Fig. 9

Lever

English

is pressed firmly onto the lever. At

this time, make certain that there

exists no clearance between the

blade holder and the rubber cap, and

furthermore ensure that the saw-

blade-installed area can function

smoothly.

CAUTION:

Do not use any saw blade with a

worn-out blade hole. Otherwise, the

saw blade can come off, resulting

in personal injury. (Fig. 11)

8. Adjusting the base

This unit employs a mechanism that can

adjust the base mounting position in three

stages without the use of a wrench or

other tools.

(1) Press a pushbutton. When you do

this, a base lever will jump out to

prepare the base for adjustment

(Fig. 12)

(2) Push up the base tip and jog the base

back and forth. (Fig. 13)

(3) You can adjust the base position in

three stages. Move the base at an

interval of about 15 mm, find the

position where the base hooks, and

press in the base lever with your

fingers. The base is secured when

you hear the clicking sound. (Fig. 14)

9. Adjusting the blade reciprocating

speed

This unit has a built-in electronic control

circuit that makes it possible to adjust the

variable speed of the saw blade either

both by pulling a switching trigger or

turning a dial. (Fig. 15)

Blade hole

Blade

Fig. 11

Push button

Base lever

Fig. 12

Base

Fig. 13

Graduation

Switch

trigger

Dial

Fig. 15

Lever

Rubber cap

Fig. 10

Base lever

Fig. 14

English

(1) If you pull the trigger further in, the

speed of the blade accelerates. Begin

cutting at a low speed to ensure the

accuracy of your target cut position.

Once you’ve obtained a sufficient

cutting depth, increase the cutting

speed.

(2) On the dial scale, “5” is the maximum

speed and “1” the minimum. The

high speed is generally suitable for

soft materials such as wood, and the

low speed is suitable for hard

materials such as metal. We

recommend that you use the following

as a rough guide in selecting the

suitable speed for the materials you

are cutting.

CAUTION:

䡬 When cutting at low speed (scale of 1 –

2), never cut a wooden board more than

25/64" (10 mm) thick or a mild steel plate

more than 5/64" (2 mm) thick. The load

on the motor can result in overheating

and damage.

䡬 Although this unit employs a powerful

motor, prolonged use at a low speed will

increase the load unduly and may lead to

overheating. Properly adjust the saw

blade to allow steady, smooth cutting

operation, avoiding any unreasonable

use such as sudden stops during cutting

operation.

10.

Adjusting the swing cutting operation

Two cutting systems can be selected with

this unit. The first is straight cutting, in

which the saw blade is moved linearly,

and the second is the swing cutting, in

which the saw blade is swung like a

pendulum. (Fig. 16, Fig. 17)

(1) Straight cutting

You can perform straight cutting by

setting the change lever widthwise.

Straight cutting should normally be

performed when cutting hard

materials such as metal, etc. (Fig. 16)

(2) Swing cutting

You can perform swing cutting by

setting the change lever lengthways.

Swing cutting should normally be

performed when cutting soft materials

such as wood, etc.

Swing cutting is efficient since the

saw blade forcibly bites into the

material. (Fig. 17)

CAUTION:

䡬 Even for soft materials, you should

perform straight cutting if you wish

to make curved or clean cuts.

䡬 Dust and dirt accumulated on the

change lever section can degrade the

function of the change lever.

Periodically clean the change lever

section.

Example of materials Recommended

to be cut dial scale

Mild steel pipes /

cast-iron tubes / 2 – 4

L-shaped angle steel

Wood / wood with nails

driven in

Stainless steel 1 – 3

Aluminum / brass / copper 2 – 4

Plaster board 4 – 5

Plastic / fiber board 1 – 3

Change lever

Straight cutting

Fig. 16

Change lever

Swing cutting

Fig. 17

English

HOW TO USE THE

RECIPROCATING SAW

CAUTION:

䡬 Avoid carrying it plugged to the outlet

with your finger on the switch. A

sudden startup can result in an

unexpected injury.

䡬 Be careful not to let sawdust, earth,

moisture, etc., enter the inside of the

machine through the plunger section

during operation. If sawdust and the like

accumulate in the plunger section,

always clean it before use.

䡬 Do not remove the front cover (refer to

Fig. 2).

Hold firmly the front cover by hand to

operate.

But, do not extend your hand or finger

beyond the flange (see Fig.18) of front

cover to avoid an injury.

䡬 During use, press the base against the

material while cutting.

Vibration can damage the saw blade if

the base is not pressed firmly against

the workpiece.

Furthermore, a tip of the saw blade can

sometimes contact the inner wall of the

pipe, damaging the saw blade.

䡬 Select a saw blade of the most

appropriate length. Ideally, the length

protruding from the base of the saw

blade after subtracting the stroke

should be larger than the material (see

Fig. 18 and Fig. 19).

If you cut a large pipe, large block of

wood, etc., that exceeds the cutting

capacity of a blade; there is a risk that

the blade may contact with the inner

wall of the pipe, wood, etc., resulting in

damage. (Fig. 20, Fig. 21)

䡬 To maximize cutting efficiency for the

materials you are using and working

conditions, adjust the speed of the saw

blade and the switching to swing cutting.

1. Cutting metallic materials

CAUTION:

䡬 Press the base firmly against the

workpiece.

䡬 Never apply any unreasonable force to

the saw blade when cutting. Doing so

can easily break the blade.

Stroke

Flange of front cover

Front cover

Fig. 18

Stroke

Fig. 19

Fig. 21

Fig. 20

English

(1) Fasten a workpiece firmly before

operation. (Fig.22)

(2) When cutting metallic materials,

use proper machine oil (turbine oil,

etc.). When not using liquid

machine oil, apply grease over the

workpiece.

CAUTION:

The service life of the saw blade will

be drastically shortened if you don’t

use machine oil.

(3) Use the dial to adjust the speed of the

saw blade to suit your working

conditions and materials.

(4) You can cut smoothly if you set the

change lever position to straight

cutting (Fig. 16).

2. Cutting lumber

(1) When cutting lumber, make sure that

the workpiece is fastened firmly

before beginning. (Fig. 23)

(2) You can cut efficiently if the speed of

the saw blade is set to dial scale “5”.

(3) You can cut efficiently if the change

lever position is set to swing cutting

(Fig. 17). Alternatively, you can cut

cleanly if the change lever position is

set to straight cutting (Fig. 16).

CAUTION:

Never apply any unreasonable force

to the saw blade when cutting. Also

remember to press the base against

the lumber firmly.

3. Sawing curved lines

We recommend that you use the

BIMETAL blade mentioned in Page 18

for the saw blade since it is tough and

hardly breaks.

CAUTION:

Delay the feed speed when cutting

the material into small circular arcs.

An unreasonably fast feed may

break the blade.

4. Plunge cutting

With this tool, you can perform pocket

cutting on plywood panels and thin

board materials. You can carry out

pocket cutting quite easily with the saw

blade installed in reverse as illustrated

in Fig. 25, Fig. 27, and Fig. 29. Use the

saw blade that is as short and thick as

possible. We recommend for this

purpose that you use BI-METAL Blade

No. 132 mentioned in Page 18. Be sure

to use caution during the cutting

operation and observe the following

procedures.

(1) Press the lower part (or the upper

part) of the base against the

material. Pull the switch trigger

while keeping the tip of the saw

blade apart from the material. (Fig.

24, Fig. 25)

Fig. 22

Fig. 23

English

(2) Raise the handle slowly and cut in

with the saw blade little by little. (Fig.

26, Fig. 27)

(3) Hold the body firmly until the saw

blade completely cuts into the

material. (Fig. 28, Fig. 29)

CAUTION:

䡬 Avoid plunge cutting for metallic

materials. This can easily damage

the blade.

䡬 Never pull the switch trigger while

the tip of the saw blade tip is

pressed against the material. If you

do so, the blade can easily be

damaged when it collides with the

material.

䡬 Make absolutely sure that you cut

slowly while holding the body

firmly. If you apply any

unreasonable force to the saw blade

during the cutting operation, the

blade can easily be damaged.

Fig. 26

Fig. 27

Fig. 24

Fig. 25

Fig. 28

Fig. 29

English

1. Inspecting the blade

Continued use of a dull or damaged blade

will result in reduced cutting efficiency

and may cause overloading of the motor.

Replace the blade with a new one as soon

as excessive abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws

and ensure that they are properly

tightened. Should any of the screws be

loosened, retighten them immediately.

WARNING: Using this reciprocating

saw with loosen screws

is extremely dangerous.

3. Maintenance of the motor

The motor unit winding is the very “heart“

of the power tool. Exercise due care to

ensure the winding does noto become

damaged and/or wet with oil or water.

4. Inspecting the carbon brushes (Fig. 30)

The Motor employs carbon brushes which

are consumable parts. When they become

worn to or near the “wear limit”, it could

result in motor trouble. When an auto-stop

carbon brush is equipped, the motor will

stop automatically. At that time, replace

both carbon brushes with new ones which

have the same carbon brush Numbers

shown in the figure. In addition, always

keep carbon brushes clean and ensure that

they slide freely within the brush holders.

MAINTENANCE AND INSPECTION

NOTE: Use HITACHI carbon brush No. 43

indicated in Fig. 30.

5. Replacing carbon brushes

Disassemble the brush caps with a

slotted-head screwdriver. The carbon

brushes can then be easily removed.

6. Service and repairs

All quality power tools will eventually

require servicing or replacement of parts

because of wear from normal use. To

assure that only authorized replacement

parts will be used, all service and repairs

must be performed by a HITACHI

AUTHORIZED SERVICE CENTER, ONLY.

7. Service parts list

CAUTION:

Repair, modification and inspection of

Hitachi Power Tools must be carried out

by an Hitachi Authorized Service Center.

This Parts List will be helpful if presented

with the tool to the Hitachi Authorized

Service Center when requesting repair

or other maintenance. In the operation

and maintenance of power tools, the

safety regulations and standards

prescribed in each country must be

observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being

improved and modified to incorporate

the latest technological advancements.

Accordingly, some parts may be changed

without prior notice.

Fig. 30

WARNING: Be sure to switch power OFF and disconnect the plug from the

receptacle during maintenance and inspection.

0.24" (6 mm)

Wear Limit

No. of Carbon

Brush

0.67” (17 mm)

English

ACCESSORIES

WARNING: ALWAYS use Only authorized HITACHI replacement parts and

accessories. NEVER use replacement parts or accessories which are

not intended for use with this tool. Contact HITACHI if you are not sure

whether it is safe to use a particular replacement part or accessory

with your tool.

The use of any other attachment or accessory can be dangerous and

could cause injury or mechanical damage.

NOTE: Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

(1) Blade (Code No. 725362)..................................................................................................... 1

(2) Case (Code No. 321142) ...................................................................................................... 1

English

OPTIONAL ACCESSORIES.......sold separately

PROG.: NEW PROGRESSIVE TOOTH HCS: HIGHSPEED CARBON STEEL

NOTE: Specifications are subject to change without any obligation on the part of the

HITACHI.

TYPE LENGTH WIDTH TPI

MATERIAL

CODE NO.

BLADES /

POUCH

6" (152 mm) 3/4" (18 mm) 6 HCS 725300 5

WOOD CUTTING 9" (228 mm) 3/4" (18 mm) 5 HCS 725301 5

12" (305 mm) 3/4" (18 mm) 6 HCS 725302 5

6" (152 mm) 3/4" (18 mm) 6 BI-METAL 725310 5

WOOD CUTTING

6" (152 mm) 3/4" (18 mm) 6 BI-METAL 725311 5

NAIL-EMBEDED

6" (152 mm) 5/8" (16 mm) 6 BI-METAL 725312 5

9" (228 mm) 3/4" (18 mm) 6 BI-METAL 725313 5

12" (305 mm) 3/4" (18 mm) 6 BI-METAL 725314 5

6" (152 mm) 3/4" (18 mm) 10 BI-METAL 725320 5

9" (228 mm) 3/4" (18 mm) 10 BI-METAL 725321 5

6" (152 mm) 3/4" (18 mm) 14 BI-METAL 725322 5

METAL CUTTING

9" (228 mm) 3/4" (18 mm) 14 BI-METAL 725323 5

6" (152 mm) 3/4" (18 mm) 18 BI-METAL 725324 5

9" (228 mm) 3/4" (18 mm) 18 BI-METAL 725326 5

6" (152 mm) 3/4" (18 mm) 24 BI-METAL 725325 5

9" (228 mm) 3/4" (18 mm) 24 BI-METAL 725327 5

6" (152 mm) 3/4" (18 mm) 10//14 BI-METAL 725330 5

ALL PURPOSE 9" (228 mm) 3/4" (18 mm) 10//14 BI-METAL 725331 5

12" (305 mm) 3/4" (18 mm) 10//14 BI-METAL 725332 5

CARBIDE GRIT 9" (228 mm) 3/4" (18 mm) GRIT — 725340 3

DEMOLITION

9" (228 mm) 7/8" (22 mm) 6 BI-METAL 725350 3

9" (228 mm) 7/8" (22 mm) 9 BI-METAL 725351 3

NEW WOOD 6" (152 mm) 3/4" (18 mm) PROG. BI-METAL 725360 5

NEW METAL 6" (152 mm) 3/4" (18 mm) PROG. BI-METAL 725361 5

NEW ALL PURPOSE 8" (203 mm) 3/4" (18 mm) PROG. BI-METAL 725362 5

Français

INFORMATIONS IMPORTANTES DE SÉCURITÉ

Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions

de fonctionnement dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé.

La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé

proviennent d’un non respect des règles ou précautions de base de sécurité. Un accident

peut la plupart du temps être évité si l’on reconnaît une situation de danger potentiel avant

qu’elle ne se produise, et en observant les procédures de sécurité appropriées.

Les précautions de base de sécurité sont mises en évidence dans la section “SECURITE” de

ce mode d’emploi et dans les sections qui contiennent les instructions de fonctionnement

et d’entretien.

Les dangers qui doivent être évités pour prévenir des blessures corporelles ou un

endommagement de la machine sont identifiés par AVERTISSEMENTS sur l’outil motorisé

et dans ce mode d’emploi.

NE JAMAIS utiliser cet outil motorisé d’une manière qui n’est pas spécifiquement

recommandée par HITACHI.

SIGNIFICATION DES MOTS D’AVERTISSEMENT

AVERTISSEMENT indique des situations potentiellement dangereuses qui, si elles sont

ignorées, pourraient entraîner la mort ou de sérieuses blessures.

PRECAUTION indique des situations dangereuses potentilles qui, si elles ne sont pas

évitées, peuvent entraîner de mineures et légères blessures ou endommager la machine.

REMARQUE met en relief des informations essentielles.

Français

SECURITE

REGLES GENERALE DE SECURITE

AVERTISSEMENT: Lire et coxmprendre toutes les instructions.

Un non respect de toutes les instructions ci-dessous peut

entraîner une électrocution, un incendie et/ou de sérieuses

blessures personnelles.

CONSERVER CES INSTRUCTIONS

1. Zone de travail

(1) Garder la zone de travail propre et bien

éclairée. Les établis mal rangés et les

zones sombres invitent aux accidents.

(2) Ne pas utiliser les outils motorisés dans

une atmosphère explosive, telle qu’en

présence de liquides inflammables, de

gaz ou de poussières. Les outils

motorisés créent des étincelles qui

risquent d’enflammer la poussière ou les

vapeurs.

(3) Tenir les spectateurs, les enfants et les

visiteurs éloignés, lors de l’utilisation de

l’outil motorisé. Une distraction peut

faire perdre le contrôle de la machine.

2. Sécurité électrique

(1) Les outils à double isolation sont équipés

d’une fiche polarisée (une lame est plus

large que l’autre). Cette fiche ne

pénétrera dans une prise secteur

polarisée que dans un sens. Si la fiche

ne rentre pas complètement dans la

prise, la retourner. Si elle ne rentre

toujours pas, contacter un électricien

qualifié pour installer une prise polarisée.

Ne pas modifier la fiche d’aucune façon.

La double isolation

élimine le besoin

d’un cordon d’alimentation à trois fils et

d’un système d’alimentation avec mises

à la terre.

(2) Eviter tout contact corporel avec les sur-

faces mises à la terre telles que les

canalisations, les radiateurs, les

réchauds et les réfrigérateurs. Il y a un

risque accru d’électrocution si son corps

est mis à la terre.

(3) Ne pas exposer les outils motorisés à la

pluie ou à l’humidité. De l’eau pénétrant

à l’intérieur de l’outil motorisé augmente

le risque d’électrocution.

(4) Ne pas maltraiter le cordon

d’alimentation. Ne jamais utiliser le cor-

don pour porter les outils ou tirer sur la

fiche du réceptacle. Garder le cordon à

l’écart de la chaleur, de l’huile, des arêtes

coupantes ou des pièces en mouvement.

Remplacer les cordons endommagés

immédiatement. Des cordons

endommagés augmentent le risque

d’électrocution.

(5) Lors de l’utilisation d’un outil motorisé,

utiliser un cordon de rallonge extérieur

marqué “W-A” ou “W”. Ces cordons

sont prévus pour une utilisation

extérieure et réduisent les risques

d’électrocution.

3. Sécurité personnelle

(1) Rester sur ses gardes, regarder ce que

l’on fait et utiliser son sens commun lors

de l’utilisation d’un outil motorisé. Ne

pas utiliser un outil en état de fatigue

ou sous l’influence de drogues, d’alcool

ou de médicaments. Un moment

d’inattention lors de l’utilisation de l’outil

motorisé peut entraîner de sérieuses

blessures personnelles.

(2) S’habiller correctement. Ne pas porter

des vêtements larges ou des bijoux.

Attacher les cheveux longs. Tenir ses

cheveux, vêtements et ses gants

éloignés des parties mobiles. Les

vêtements larges, les bijoux et les

cheveux longs peuvent se prendre dans

les parties mobiles.

La page charge ...

Hitachi CR 13VB Instruction Manual And Safety Instructions

Marque: Hitachi

Modèle: CR 13VB

Catégorie: Outils électroportatifs

Taper: Instruction Manual And Safety Instructions

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi CR 13VB
español: Hitachi CR 13VB

Hitachi CR 13VB Instruction Manual And Safety Instructions

Hitachi CR 13VB Instruction Manual And Safety Instructions

dans d''autres langues

Documents connexes