GE GTW720BPNDG Guide d'installation

WASHERS

SAFETY INSTRUCTIONS ..........4

USING THE WASHER

Getting Started ...................... 6

Loading .............................16

Appliance Communication .............17

CARE AND CLEANING ............18

INSTALLATION

INSTRUCTIONS

.................... 19

TROUBLESHOOTING TIPS ..... 24

LIMITED WARRANTY ............27

CONSUMER SUPPORT .......... 30

OWNER’S MANUAL &

INSTALLATION

INSTRUCTIONS

Write the model and serial

numbers here:

Model # _________________

Serial # _________________

You can find them under the

lid of the washer.

49-3000187 Rev. 1 03-20 GEA

G016

GE is a trademark of the General Electric Company. Manufactured under trademark license.

GTW845

GTW840

GTW725

GTW720

ENGLISH/FRANÇAIS/

ESPAÑOL

2 49-3000187 Rev. 1

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Register your GE appliance now online. Helpful websites and phone numbers are available in the

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-3000187 Rev. 1 3

WELCOME

Notes

4 49-3000187 Rev. 1

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

To reduce the risk of death, fire, explosion, electric shock, or injury to persons when using

your appliance, follow basic precautions, including the following:

Ŷ

Read all instructions before using the appliance.

Ŷ

Follow all fabric care instructions and warnings to prevent melting of garments or damage to the appliance.

Ŷ

DO NOT wash or dry articles that have been previously cleaned in, washed in, soaked in or spotted with

gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could

ignite or explode.

Ŷ

DO NOT add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water.

These substances give off vapors that could ignite or explode.

Ŷ

Under certain conditions, hydrogen gas may be produced in a hot-water system that has not been used for

2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a

period, before using a washing machine, turn on all hot-water faucets and let the water flow from each for

several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, DO NOT smoke

or use an open flame during this time.

Ŷ

DO NOT allow children to play on or in this appliance. Close supervision of children is necessary when this

appliance is used near children. Before the washer is removed from service or discarded, remove the door or

lid. Failure to follow these instructions may result in death or injury to persons.

Ŷ

DO NOT reach into the appliance if the tub or agitator is moving to prevent accidental entanglement.

Ŷ

For waterproof, water-resistant and bulky items, only use the Bulky Items (or Delicates) cycle. DO NOT use

other cycles for these items. Using other cycles can cause excessive vibration and may result in injury or

damage to the washer, walls, or floor. DO NOT mix waterproof and non-waterproof items.

Ŷ

DO NOT install or store this appliance where it will be exposed to the weather.

Ŷ

DO NOT tamper with controls, repair or replace any part of this appliance or attempt any servicing unless

specifically recommended in the user maintenance instructions or in published user repair instructions that you

understand and have the skills to carry out.

Ŷ

DO NOT operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or

broken parts including a damaged cord or plug.

Ŷ

Unplug the appliance or turn off the circuit breaker before servicing. Pressing the Power button DOES NOT

disconnect power.

Ŷ

See “ELECTRICAL REQUIREMENTS” located in the Installation Instructions for grounding instructions.

WARNING

49-3000187 Rev. 1 5

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

SAFETY INFORMATION

PROPER INSTALLATION

This washer must be properly installed and located in accordance with the Installation Instructions before it is used.

Ŷ

Ensure that the hot water hose is connected to the “H” valve and the cold water hose is connected to the “C”

valve.

Ŷ

Install or store where it will not be exposed to temperatures below freezing or exposed to the weather, which

could cause permanent damage and invalidate the warranty.

Ŷ

Properly ground washer to conform with all governing codes and ordinances. Follow details in the Installation

Instructions.

Ŷ

Ensure washer is properly leveled and washer legs are adjusted such that unit is stable.

Ŷ

Optional drain hose extension recommended for discharging heights from 60” - 96”.

Ŷ

GE Appliances strongly recommends the use of factory specified parts. A list of factory hoses available for

purchase are listed. These hoses are manufactured and tested to meet GE Appliances specifications.

Ŷ

GE Appliances strongly recommends the use of new water supply hoses. Hoses degrade over time and need

to be replaced every 5 years to reduce the risk of hose failures and water damage.

PARTS AND ACCESSORIES

Order on-line at GEApplianceparts.com today,

24 hours a day or by phone at 800.626.2002 during

normal business hours. In Canada, visit your local

GE Appliances parts distributor or call 800.661.1616.

Part Number Accessory

PM14X10002 4 ft rubber water supply hoses

Or

PM14X10005 4 ft braided water supply hoses

WH49X301 Drain hose extension

PM7X1 Washer Floor Tray

START-UP SEQUENCE

Ŷ

Any time the washer is being started or restarts after the washer lid has been opened and closed, the washer

will turn on the cold water valve for two short periods followed by a 10 second pause before continuing. If the

lid is opened during this period, the washer will pause. You will have to push the Start button again to restart

the cycle.

WHEN NOT IN USE

Ŷ

Turn off water faucets to minimize leakage if a break or rupture should occur. Check the condition of the fill

hoses; GE Appliances recommends changing the hoses every 5 years.

AUTOMATIC DRAIN SEQUENCE

Ŷ

Machine will automatically drain any time the lid is left open for more than 15 minutes and water is present.

Ŷ

Machine will automatically drain if left in a paused state with the lid closed for more than 24 hours and water is

present.

Ŷ

Machine will automatically drain after dispensing water in Water Station mode after the cycle knob has been

turned to another cycle.

6 49-3000187 Rev. 1

Getting started

USING THE WASHER

Throughout this manual, features and appearance may vary from your model.

To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY

INSTRUCTIONS before operating this appliance.

WARNING

• Loosely add items around

agitator or Infusor. Overloading

may negatively impact wash

performance. See page 16 for

suggested loading examples.

• If not using a dispenser,

add the manufacturer’s

recommended amount of

detergent to the top of the

load after adding clothes.

We recommend the use of

High Efficiency detergents

such as

Tide HE Turbo

™ in

your energy efficient washer.

Step 2

Step 3

Step 4

Step 1

• Close lid.

NOTE: Unit will not

start with lid open

except on Bulky Items

cycle.

• Select wash cycle.

• Select wash options,

including Deep Rinse

option when using

fabric softener.

• Select options.

•

Press

Start.

• Add fabric softener to the fabric

softener dispenser.

IMPORTANT: For detergent

use, see the specific dispenser

section in this manual for your

model.

• If using detergent packets, add

to the Laundry Pack Dispenser

cup (on some models) or add

to the bottom of the wash

basket before adding clothes.

We recommend the use of

High Efficiency laundry packs

such as Tide PODS™ or Gain

Flings™.

D

C

A

B

G

HI

I

H

I

F

A

Power

Press to “wake up” the display. If the display is active, press to put the washer into idle mode.

NOTE: Pressing Power does not disconnect the appliance from the power supply.

D CA

B

G

I

J

H

E

49-3000187 Rev. 1 7

USING THE WASHER

Getting started

Start/Pause

Press Start to begin the cycle. NOTE: Unless Bulky Items cycle is selected, the lid must be closed for the washer to start cycle.

If the lid is open, “Lid” will scroll across the display. During the load sensing portion of the cycle, the lid will lock and “SEnSing” will

scroll across the display. When load sensing is complete, the lid will unlock.

Pressing Pause will unlock the lid (if locked at that time), pause the cycle and the Start indicator light will blink.

To continue the cycle, press Start again. If water remains in the machine, select the Drain & Spin cycle to drain basket and

spin water out of the washer basket. NOTE: Machine will automatically cancel and drain when water is present and the lid is

left open for 15 minutes or the unit is left in a paused state for 24 hours with the lid closed. Select cycle and press Start to

begin new cycle.

Display and Status Lights

Display: The display shows the approximate time remaining until the end of the cycle. NOTE: The cycle time is affected by

how long it takes the washer to fill. This depends on the water pressure in your home. The size of the load being washed also

significantly impacts cycle time, with larger loads taking longer.

In addition, this display will, “scroll” the washer status:

• bALAnCIN

g

Start of rebalancing cycle to redistribute clothes. Stops after rebalancing is complete.

• dELAY When Delay Wash is initiated. Replaced with estimated time when cycle starts.

• End End of current cycle.

• FILL “FILL” will scroll across display for the first 45 seconds of fill, afterwards the estimated end of cycle time is

displayed.

• H2O SUPPLY Can not sense water level (valves possibly turned off).

• LId Cycle stopped because lid is open. Close the lid.

• SEnSIng Sensing out-of-balance condition, waterproof items, or load size and type before and during fill (normal).

• PAUSE Cycle paused because the Start/Pause button was pressed and the washer was set to Pause. Press Start

button again to restart the cycle.

Cycle status lights: Shows whether the washer is in the Pre-wash, Delay, Fill, Soak, Wash, Rinse or Spin portion of the

cycle. NOTE: Cycle status lights vary by model.

If an out-of-balance condition is detected by the washer, the Spin light will blink during the remaining portion of the cycle

and will stay illuminated for a short time after cycle completion. When this occurs, the washer is taking actions to correct the

out-of-balance condition and complete the cycle normally. In some cases, the washer may not be able to balance the load

and spin up to full speed. If you notice the load is more wet than normal at the end of the cycle, redistribute the load evenly

in the wash basket and run a Drain & Spin cycle.

C

Your washer is equipped with Consumer Help Indicator (CHI). CHI is our way to communicate a simple remedy for some situations

that you can perform without the need to call for service. The chart below describes the helpful messages you may notice scrolling

on your display when you return to start another load. These messages will provide simple remedies you can quickly perform.

Spin light blinking If an out-of-balance condition is detected by the washer, the Spin light will blink during the remaining portion

of the cycle and will stay illuminated for a short time after cycle completion. When this occurs, the washer

is taking actions to correct the out-of-balance condition and complete the cycle normally. In some cases,

the washer may not be able to balance the load and spin up to full speed. If you notice the load is more wet than

normal at the end of the cycle, redistribute the load evenly in the wash basket and run a Drain & Spin cycle.

“H2O SUPPLY”

(Water not

entering washer)

Check your house water supply. Did you forget to turn on one or both supply valves after installation or

coming back from vacation? As soon as the message starts to scroll, the washer will initiate a 4 minute lock-

out period. The washer controls won’t respond/change during this time. After the 4 minutes, you can begin

your cycle again. If you try to bypass the lock-out period by unplugging the washer, the 4 minute timer will

start over again.

“CAnCELEd” “CAnCELEd” may scroll on the display if the machine was paused for longer than 24 hours or if the machine

has stopped itself before the cycle completed due to certain errors. As soon as the message starts to scroll,

the washer will initiate a 4 minute lock-out period. The washer controls won’t respond/change during this time.

After the 4 minute period, you can begin your cycle again. If you try to bypass the lock-out period by unplugging

the washer, the 4 minute timer will start over again. If the problem persists, call GE Appliances at 800.

GE.CARES (800.432.2737) for service.

“Lid” “Lid” will be shown on display if 3 cycles have been started without opening the lid. The washer will not

start another cycle until the lid is opened. Try opening, then closing the lid and starting a new cycle. If the

problem persists, call GE Appliances at 800.GE.CARES (800.432.2737) for service.

Consumer Help Indicator

B

Feature status lights indicate (see sections F and G for more details):

Pause - Will display when washer is paused between cycles.

Controls - The washer is locked - will blink once if you press any button or turn the cycle knob.

Lid Lock - The lid is locked. See the Control Lock description.

WiFi (on some models) - Will display when washer is connected via WiFi. Will blink when you are attempting to connect

your device to your home WiFi.

Spin Stop - Indicates wash basket is coasting to a stop following spin. Lid will not unlock until basket has fully come to a stop.

8 49-3000187 Rev. 1

Getting started

USING THE WASHER

D

Items to Wash Cycle Wash Temp Soil Level Spin

Selection

(Duration)

Options Available Cycle Details

Cycle for normal,

regular, or typical

use for washing

up to a full load

of normally soiled

cotton clothing.

Colors Hot

Warm

Colors

Cool

Cold

Tap Cold

Ex. Heavy

Heavy

Normal

Light

Max

More

Normal

No Spin

Stain Removal Guide

Warm Rinse

Auto Soak

Deep Rinse

Delay Wash

Extra Rinse

Power Pre-Wash

Cycle for normal, regular, or typical

use for washing up to a full load

of normally soiled cotton clothing.

Choose the Heavy or Extra Heavy soil

level selection and Warm or Hot water

temperature selection as appropriate

for your clothes load for a higher

degree of cleaning. Incorporates multi-

stage fills and wash periods to provide

optimal fabric care.

Casual clothes,

lightly soiled

office wear.

Casuals Hot

Warm

Colors

Cool

Cold

Tap Cold

Ex. Heavy

Heavy

Normal

Light

Max

More

Normal

No Spin

Stain Removal Guide

Deep Fill

Warm Rinse

Auto Soak

Deep Rinse

Delay Wash

Extra Rinse

Power Pre-Wash

Wash cycle tailored to care for

casual clothes and office wear

items.

Lingerie and

special care

fabrics with light

soil.

Delicates Hot

Warm

Colors

Cool

Cold

Tap Cold

Ex. Heavy

Heavy

Normal

Light

Max

More

Normal

No Spin

Stain Removal Guide

Deep Fill

Warm Rinse

Auto Soak

Deep Rinse

Delay Wash

Extra Rinse

Power Pre-Wash

Utilizes an extra gentle agitate

profile and a low spin speed to

provide special care to delicate

fabrics. It is recommended to place

small or ultra delicate items in mesh

bags before washing.

Medium to lightly

soiled athletic

wear items of

technical or

synthetic fabrics.

Active

Wear

Hot

Warm

Colors

Cool

Cold

Tap Cold

Ex. Heavy

Heavy

Normal

Light

Max

More

Normal

No Spin

Stain Removal Guide

Deep Fill

Warm Rinse

Auto Soak

Deep Rinse

Delay Wash

Extra Rinse

Power Pre-Wash

Cycle designed for care of medium

to lightly soiled active wear,

athletic wear, and technical fabrics.

Incorporates a dual stage wash

period to effectively treat body soils

and odors. Use the Heavy Duty cycle

for heavily soiled sports clothing

constructed of sturdy fabric.

Small loads of

lightly soiled

items that are

needed in a hurry.

Examples include

one casual wear

outfit or 3 soccer

uniforms.

Quick

Wash

Hot

Warm

Colors

Cool

Ex. Heavy

Heavy

Normal

Light

Max

More

Normal

No Spin

Stain Removal Guide

Deep Fill

Warm Rinse

Auto Soak

Deep Rinse

Delay Wash

Extra Rinse

Power Pre-Wash

Utilizes more intense agitation

profile and expedited wash period

to clean small lightly soiled loads in

the fastest time possible.

Wet load of items.

For items that

need only to be

rinsed, use this

cycle with Deep

Rinse option.

Drain &

Spin

Max

More

Normal

No Spin

Deep Rinse

Extra Rinse

Utilizes a high speed spin to extract

water from wet items. For items that

need to be rinsed, select the Deep

Rinse option when using this cycle.

Wash Cycles-Cycle Selector Knob

The wash cycle controls the type of washing process. The cycle selector knob can be turned in either direction. Turning the

knob after starting a cycle will stop the washer and change the cycle/options to the new selection. Press Start to begin the

new cycle selection.

The chart below will help you match the items to be washed with the best wash cycle settings. For optimal performance,

select the cycle that most closely matches the items being washed.

Selections and options shown in bold are the recommended settings for that cycle.

Some cycles and options may not be available on some models.

49-3000187 Rev. 1 9

USING THE WASHER

Getting started

Items to Wash Cycle Wash Temp Soil Level Spin

Selection

(Duration)

Options Available Cycle Details

Heavily soiled

colorfast items.

Sanitize

with Oxi*

Hot Ex. Heavy Max

More

Warm Rinse

Auto Soak

Deep Rinse

Delay Wash

Extra Rinse

Cycle uses an initial lower water

fill for super concentrated, high

temperature sanitization followed by

a heavy wash step. A pump purge

and deep rinse is incorporated to

remove contaminants. See additional

details and certifications below. Smart

Dispense not available on this cycle.

Jeans with

medium to light

soil. For heavily

soiled work jeans,

use the Heavy

Duty Cycle.

Jeans Hot

Warm

Colors

Cool

Cold

Tap Cold

Ex. Heavy

Heavy

Normal

Light

Max

More

Normal

No Spin

Stain Removal Guide

Deep Fill

Warm Rinse

Auto Soak

Deep Rinse

Delay Wash

Extra Rinse

Power Pre-Wash

Combines higher water levels,

a specially designed agitation

profile, and multi-step wash to

care for jeans with medium to

light soil. Use the Heavy Duty

cycle for heavily soiled work

jeans.

Sturdy fabrics with

heavy to medium

soil.

Deep

Clean

Hot

Warm

Colors

Cool

Cold

Tap Cold

Ex. Heavy

Heavy

Normal

Light

Max

More

Normal

No Spin

Stain Removal Guide

Deep Fill

Warm Rinse

Auto Soak

Deep Rinse

Delay Wash

Extra Rinse

Power Pre-Wash

Incorporates multi-step wash

periods combined with extended

wash periods to effectively clean

heavily to medium soiled sturdy

fabrics.

Water-resistant,

bedding and

bulky items, such

as large coats,

mattress pads,

and bath mats.

Bulky

Items

Hot

Warm

Colors

Cool

Cold

Tap Cold

Ex. Heavy

Heavy

Normal

Light

Max

More

Normal

No Spin

Stain Removal Guide

Deep Fill

Warm Rinse

Auto Soak

Deep Rinse

Delay Wash

Extra Rinse

Power Pre-Wash

Provides a Deep Fill/max fill wash

water level to wash bulky and

waterproof items. Also incorporates

a Deep Fill rinse to effectively rinse

bulky items and a low spin speed

appropriate for these items. Only

use this cycle for water-resistant,

bedding or bulky items.

Towels

Sheets

Towels /

Sheets

Hot

Warm

Colors

Cool

Cold

Tap Cold

Ex. Heavy

Heavy

Normal

Light

Max

More

Normal

No Spin

Stain Removal Guide

Deep Fill

Warm Rinse

Auto Soak

Deep Rinse

Delay Wash

Extra Rinse

Power Pre-Wash

Cycle designed washing towels

or sheets, using a higher water

level to effectively clean these

items. It is recommended that

towels and sheets be washed

separately for best care and washing

performance. For waterproof bed

covers use Bulky Items cycle.

Whites and

household linens

Whites Hot

Warm

Colors

Cool

Cold

Tap Cold

Ex. Heavy

Heavy

Normal

Light

Max

More

Normal

No Spin

Stain Removal Guide

Deep Fill

Warm Rinse

Auto Soak

Deep Rinse

Delay Wash

Extra Rinse

Power Pre-Wash

Cycle tailored to clean and brighten

your whites.

Failure to follow these instructions may result in injury or property damage.

For Waterproof, Water-Resistant, or Bulky Items:

•

Only use the Bulky Items (or Delicates) cycle. NOTE: Some models only have a Delicates cycle

.

•

Using other cycles can cause excessive vibration and may result in injury or damage to the washer, walls, or

floor.

•

Do not mix waterproof and non-waterproof items

.

•

Read the Owner’s Manual for wash cycle details.

CAUTION

10 49-3000187 Rev. 1

Getting started

USING THE WASHER

*Sanitize with Oxi

The Sanitize With Oxi cycle, when using an Oxi additive along with your detergent, is designed to remove 99.9% of bacteria found in

home laundry. Measure the detergent and the Oxi products carefully. Using the amounts appropriate for a large heavily soiled load

in a top load washer, follow the detergent and the Oxi product label instructions. For the Sanitize With Oxi cycle only, add the clothes

first and then place the detergent and Oxi product directly on top of the load. The washer hot water supply connection must provide

a minimum of 120°F to ensure the effectiveness of this cycle.

NOTE: The default Sanitize With Oxi cycle water temperature can NOT be changed.

This feature is for pretreating of garments

only and not intended to serve as an

actual wash cycle. When selected, the

washer will supply either fresh water or

water mixed with detergent from your

SmartDispense system for garment hand

pre-washing or pre-treating use.

The pretreating water will be dispensed

from the area located in the back of

the main opening of the washer. When

selected, any water dispensed into the

wash tub during the pretreat will be drained

from the machine before any subsequently

selected wash cycle can begin.

Alternatively, you can use this feature to

soak your garments in the pretreated water

for up to 24 hours with the lid closed and

the cycle knob remaining on Water Station.

In order to use this feature to soak, keep

dial on Water Station and close the lid.

You can soak for up to 24 hours before

the water in the tub will be automatically

drained. Rotating the dial, holding the

Start button for 3 seconds or leaving the

lid open for more than 15 minutes will all

automatically drain the water from the tub.

Pretreating or Soaking Using Water Station (on some models)

Water Station only

Select this feature:

1. Rotate the cycle selection knob to Water Station.

2. Push the Select button until the LED below Water is

illuminated.

3. Select the desired water temperature using the Temp

button.

4. Press the Start button to initiate the feature.

If the lid is not already open, raise the lid of the washer to

start the flow of fresh water from the dispensing area. Water

will continue to be dispensed until the lid is closed or the

water level in the tub reaches the maximum level.

If the lid is closed before the maximum level in the tub is

reached, additional water can be dispensed by opening

the lid again. Once the lid is closed, water dispensed using

the water on demand feature will remain in the tub until the

cycle selection knob is rotated to an actual wash cycle, or

the Start button is held in for 3 seconds, at which point the

water in the tub will be drained out of the machine.

If the lid is not closed, the water in the tub will automatically

be drained after 15 minutes. With the lid closed, if the cycle

selection knob is not rotated to an actual wash cycle, or the

Start button is not held in for 3 seconds, the water in the

tub will automatically be drained after 24 hours.

Water Station with Detergent

Select this feature:

1.

Rotating the cycle selection knob to the Water Station.

2.

Push the Select button until the LED below Detergent +

Water is illuminated.

3.

Select the desired water temperature using the Temp

button.

4.

Press the Start button to initiate the detergent feature.

If the lid is not already open, raise the lid of the washer

to start the flow of soapy water from the dispensing area.

Soapy water will continue to be dispensed until the lid is

closed or the water level in the tub reaches the maximum

level.

If the lid is closed before the maximum level in the tub

is reached, additional soapy water can be dispensed by

simply opening the lid again. Once the lid is closed, soapy

water dispensed will remain in the tub until the cycle

selection knob is rotated to an actual wash cycle, or the

Start button is held in for 3 seconds, at which point the

soapy water in the tub will be drained out of the machine.

If the lid is not closed, the soapy water in the tub will

automatically be drained after 15 minutes. With the lid

closed, if the cycle selection knob is not rotated to an actual

wash cycle, or the Start button is not held in for 3 seconds,

the soapy water in the tub will automatically be drained

after 24 hours.

E

49-3000187 Rev. 1 11

USING THE WASHER

Getting started

F

Stain Removal Guide (on some models)

The Stain Removal Guide feature allows you to indicate what stains are on the garments in your load. An initial water fill

is performed at a temperature tailored to the stain type selected and to an amount which enables a concentrated cleaning

step. A stain scrubbing period, followed by an active soak, is conducted to effectively treat the stain. Then additional water

is added to the selected temperature and the wash phase is conducted for the cycle selected.

This feature can be applied to most wash cycles as described in the cycle guide.

To use Stain Removal Guide:

1. Select the desired wash cycle.

2. Press the Stain Removal Guide button.

Continue to press to select Tomato stain, Wine stain, Blood stain, Grass stain or Dirt stain. The indicator light will show

the selected stain.

To select a different stain, press the Stain Removal Guide button until desired stain to be removed is lit.

To turn off Stain Removal Guide, press until no indicator lights are illuminated.

NOTE: The Soil and Temperature levels will be changed to match the recommended default setting for each stain type.

Turning off Stain Removal Guide will return the settings to default.

Stain Removal Guide

Category

Recommended

Temperatures

Treatment/Wash

Stain

For best results,

before placing in washer:

Blood Cold/Cool Blood

Sweat

Body Fluids

Urine

Rinse in cold water; pretreat

stain with liquid detergent or

stain remover product.

Grass Cold/Warm Grass

Lipstick

Chocolate

Gravy

Mayonnaise

BBQ Sauce

Pretreat with liquid

detergent or stain remover

product. Brush lightly; rinse

with cold water.

Dirt Cool/Warm Dirt

Clay

Mud

Allow dirt to dry; remove

loose dirt using a brush.

Rinse with cool water.

Tomato Cool/Warm Sauce

Catsup

Salsa

Pretreat with liquid

detergent or stain remover

product; rinse with cool

water.

Wine Cool/Warm Wine

Soda

Kool-Aid

Tea

Coffee

Juice

Beer

Pretreat with mixture of Oxi

product and cool water.

Add Oxi product along with

detergent in the washer.

• Recommended temperatures are optimal for stain removal performance; adjust temperature selection to suit load being

washed.

• Ensure stain is completely removed after wash cycle and before placing in dryer; very tough stains may require a second

treatment.

12 49-3000187 Rev. 1

Getting started

USING THE WASHER

Cycle Options

Deep Fill

Select the Deep Fill feature for loads where extra water is needed. The Deep Fill feature is recommended for special case

loads only, not for typical use.

Press and release the Deep Fill button once before starting the cycle to add 3 addition gallons of water to the wash load. Holding

the Deep Fill button for 3 seconds will provide the deepest fill level possible; this will increase cycle time due to the additional time

it takes to fill the washer.

To cancel the option if desired, press the Deep Fill button again.

NOTE: The Deep Fill button can also be pressed after the washer has completed filling and is in the wash phase if additional

water is desired. To stop the extra fill, press the Deep Fill button again and the water will stop.

Power Pre-wash

Ideal for heavily soiled loads, this cycle option works with SmartDispense™ to add a brief wash, soak and drain cycle to loosen

and remove heavy soil before starting the cycle selected.

Warm Rinse

Provides a warm rinse to your wash load. Note that rinsing operations may be different with this operation selected in order to

effectively apply the warm rinse water to your load.

Auto Soak

This option begins with a brief agitation, soaks for a specified period of time, then moves through the rest of the cycle

automatically. Repeated pressing of the Soak button will scroll through 15 minute, 30 minute, 1 hour and 2 hour selections and

then return back to 0 soak minutes.

Deep Rinse

Set this option to provide a deep rinse or when using fabric softener. It may change other settings (e.g. Spin may go to a higher

setting) to maximize performance.

Delay Wash

When the Delay Wash button is repeatedly pressed, the delay time is set from 1 (01H) to 9 (09H) hours and back to clear (00H)

hours. If you

press and hold the Delay Wash button for 3 seconds, it will immediately reset.

Extra Rinse

When you use extra detergent or bleach to clean heavily soiled clothes, use the Extra Rinse option to better remove additional

residues. NOTE: This option is not allowed for some cycles.

Additional Options

My Cycle Settings

As the cycle selector knob is turned, the Temp, Soil and Spin settings change to automatic pre-set default settings for each

cycle. If you desire different default settings, select the desired options or changes to the cycle settings, then press and hold

the My Cycle button for 3 seconds to store them. The My Cycle button will light when active. In the future, when you

turn the selector knob to that cycle, your settings will be automatically recalled. To restore the factory defaults temporarily

(i.e. for this load), press the My Cycle button for 1/2 second. The My Cycle light will turn off and the factory defaults will

load. However, the next time you select this cycle, your My Cycle settings will load. If you wish to permanently restore the

factory default settings for the cycle; when the My Cycle is active (button light on) press and hold the My Cycle button for 3

seconds. The factory defaults will load for the selected cycle and the My Cycle light will turn off. The default settings will load

when this cycle is selected in the future and the My Cycle light will remain off. NOTE: My Cycle saves the following options:

Temp, Soil, Spin, Extra Rinse, Deep Fill, Warm Rinse, Auto Soak, Deep Rinse and Stain Removal Guide.

Sound (on some models)

Use the Volume button to change the volume of the end of cycle signal and other system tones. Press the button until you reach

the desired volume (high, medium, low) or off.

Control Lock

Use the control lock before or during a cycle to prevent any selections from being made.

To lock/unlock the washer controls, press and hold the Warm Rinse and Auto Soak buttons for 3 seconds. The control lock

icon will light up when it is on. NOTE: The Power button can still be used when the machine is locked.

H

I

Settings

Individual settings for agitation (Soil), water temperature (Temp), and spin (Spin) can be set from the minimum (lowest in

column) to maximum (highest in column). In general, the higher up the column, the more washer energy will be used.

NOTE: Longer Spin times typically reduce dryer time/energy usage (i.e. reduces total energy when using both a washer and

a dryer).

G

49-3000187 Rev. 1 13

USING THE WASHER

Getting started

J

When selected, this feature will automatically add

detergent to the wash, eliminating the need to add

detergent for each load.

The detergent amount selection on the

control panel will default to AUTO when

first powering up the washing machine.

When AUTO is selected, the amount of

detergent needed for each laundry load

will automatically be determined based

on the size of the load the machine

senses.

If it is desired to manually select the

amount of detergent for a given load,

this can be done by pressing the Select

button on the Smart Dispense control panel to choose

between Less or More detergent. Less will provide less

detergent than the Auto selection and More will provide

more detergent than the Auto selection.

The smart dispense feature can be disabled by pressing

the Select button on the Smart Dispense control panel

until Off is selected.

NOTE: Not all cycles will allow the use of the

SmartDispense feature. If the Off LED is illuminated and

pressing the Select button results in a beeping tone, then

SmartDispense is not allowed for the cycle that has been

selected. Detergent will need to be added directly to the

wash basket for these cycles.

This model does not have a dispenser drawer for detergent

since it has a bulk detergent dispensing system.

NOTE: If it is desired to manually add detergent for a

load, that detergent will need to be added directly to

the basket, and the smart dispense set to OFF for that

particular load.

NOTE: The right side of the dispensing area in the rear of

the washer opening does NOT pull out. It is a spout only

for water and detergent to flow from the smart dispense

system.

This machine is equipped with a bulk detergent reservoir

that can hold approximately 75 ounces of liquid detergent

for your convenience. This is enough detergent for about

50 average laundry loads, depending on what dispense

amount is selected.

When the Tank Low or Tank Empty LED is illuminated,

more detergent should be added to the reservoir to ensure

detergent will be available for the next cycle.

The filling port of the detergent reservoir is located on the

front left of the washing machine. To fill the reservoir with

liquid detergent, first open the tank lid by rotating the small

lid clockwise. Then pour LIQUID detergent into the opening

until the level reaches the MAX indicator located inside

the filling port, also indicated with the horizontal line next

to the MAX lettering. Filling to this MAX level will provide

detergent for about 50 average laundry loads.

NOTE: If it is desired to change detergent type in the

detergent tank, it is not required to flush the smart dispense

system. The new detergent type can be added to a partially-

filled tank, however it will not be immediately dispensed

until the original detergent is completely dispensed from the

system.

NOTE: In the event that excessive chlorine bleach is

accidentally spilled or otherwise gets into the detergent

tank, please follow the Detergent Tank Clean-Out

instructions in the Care and Cleaning section in order to

minimize the possibility for clothing damage. If only a few

drops of bleach are spilled into the detergent tank, there is

no need to flush the tank.

Adding Detergent to SmartDispenser™

(

GTW840 and GTW845 models only

)

Conditioner

MAX

Pretreatment

Water On Demand

Bulk Dispensing

Spout Only

Do NOT pull

SmartDispense™

(

GTW840 and GTW845 models only

)

14 49-3000187 Rev. 1

Getting started

USING THE WASHER

Use a measuring cup to pour the bleach into the bleach

dispenser. Measure liquid bleach carefully and DO NOT pour

directly from the bleach bottle into the bleach dispenser.

NOTE: The bleach dispenser is a single use dispenser and is

NOT a bulk dispense system. The maximum amount of bleach

that should be poured into this dispenser for any load should

never exceed 1 cup.

NOTE: In the event that excessive chlorine bleach is

accidentally spilled or otherwise gets into the detergent tank,

please follow the Detergent Tank Clean-Out instructions in the

Care and Cleaning section in order to minimize the possibility

for clothing damage. If only a few drops of bleach are spilled

into the detergent tank, there is no need to flush the tank.

NOTE: In the event that detergent is accidentally spilled or

otherwise gets into the bleach opening, that detergent will

simply be used for the next wash cycle. In this case there is no

need to perform any flushing routine.

Liquid Bleach

(GTW840 and GTW845 models only)

Liquid fabric softener/conditioner should be added to the small

drawer in the rear of the washer opening. Follow the liquid

fabric softener/conditioner manufacturer’s recommendations

for the correct amount of softener/conditioner, based on the

load size. Do not overfill or dilute softener/conditioner as this

can result in additive being dispensed prematurely in the wash

cycle. Your option selections will determine when liquid fabric

softener/conditioner is automatically dispensed at its optimal

time in the rinse cycle.

NOTE: Fabric softener crystals should NOT be added to the

dispenser drawer, as they will not dispense properly.

Liquid Fabric Softener/Conditioner Dispenser

(GTW840 and GTW845 models only)

MAX

Pretreatment

Water On Demand

Conditioner

49-3000187 Rev. 1 15

USING THE WASHER

Getting started

Liquid chlorine bleach should be added through the

bleach dispenser in the front left corner. Follow bleach

manufacturer’s recommendations for the correct amount of

liquid chlorine bleach based on load size, taking care to not

apply or spill it directly on clothing.

NOTE: Do not use liquid chlorine bleach and laundry

pretreatments such as an Oxi product in the same wash load.

Liquid Bleach Dispenser

(GTW720 and GTW725 models only)

HE detergent should be added to the right side of the

dispenser drawer. Follow the detergent manufacturer’s

recommendations for the correct amount of detergent,

based on load size, taking care to add detergent to the right

compartment. Do not overfill or dilute detergent as this can

result in additive being dispensed prematurely in the wash

cycle. Your option selections will determine when detergent is

automatically dispensed at its optimal time in the wash cycle.

For optimal performance, especially when selecting cooler

temperature and in cold weather climates, place powdered HE

detergent directly on top of the load.

NOTE: Single-dose laundry packets should not be added to

the detergent dispenser, as they will not dispense properly. Put

packets in the Laundry Pack Dispenser Cup.

Detergent Dispenser

(GTW720 and GTW725 models only)

Liquid fabric softener/conditioner should be added to the left

side of the dispenser drawer. Follow the liquid fabric softener/

conditioner manufacturer’s recommendations for the correct

amount of softener/conditioner, based on load size, taking care

to add softener/conditioner to the left compartment. Do not

overfill or dilute softener/conditioner as this can result in additive

being dispensed prematurely in the wash cycle. Your option

selections will determine when liquid fabric softener/conditioner

is automatically dispensed at its optimal time in the rinse cycle.

NOTE: Fabric softener crystals should NOT be added to the

dispenser drawer, as they will not dispense properly.

Detergent packets (Laundry Packs) should be added to

the Laundry Pack Dispenser cup. Follow the detergent

manufacturer’s recommendations for the correct number

of detergent packets for your wash load. Do not add more

detergent packets than recommended as this can result in

residual detergent being leftover at the end of the cycle. Your

option selections will determine when detergent is automatically

dispensed at its optimal time in the wash cycle.

NOTE: We recommend the use of High Efficiency

laundry

packs such as Tide PODS™ or Gain Flings™. Some detergent

packs may not dispense completely at very cold temperatures

or in the delicate cycle. In these cases, you may use a warmer

temperature setting or, in rare cases, remove the outer cup

to use the secondary, larger chamber to dispense harder to

dissolve detergent packs.

Liquid Fabric Softener/Conditioner Dispenser

(GTW720 and GTW725 models only)

Laundry Pack Dispenser

(GTW720 and GTW725 models only)

16 49-3000187 Rev. 1

Loading

LOADING

DO NOT wash fabrics soiled with flammable liquids or cleaning solvents.

No washer can completely remove oil.

DO NOT wash or dry anything that has been soaked in or spotted with any type of oil (including cooking oils).

DO NOT reach into the washer until all moving parts have stopped.

Doing so can result in death, explosion, fire or amputation.

Always follow fabric manufacturer’s care label when laundering.

Proper Use of Detergent

Using too little or too much detergent is a common cause of

laundry problems.

Use less detergent if you have soft water, a smaller load or a lightly

soiled load.

For spots, apply pre-treatment to items as recommended on the

product label. Application should be made in the basket to prevent

overspray which may cause the coloring on the lid or graphics to

fade.

Place detergent packets in the Laundry Pack Dispenser (on

some models) or the bottom of the wash basket before adding

clothes.

GE Appliances recommends the use of High Efficiency detergents

such as Tide HE Turbo™ in your energy efficient washer. HE

detergents are formulated to work with low water wash and

rinse systems. HE detergents reduce the oversudsing problems

commonly associated with regular detergents.

When using high efficiency or concentrated detergents, consult

the product label to determine amount required for optimum

performance. Excessive detergent will negatively impact wash

performance.

Sorting Wash Loads

Sort by color (whites, lights, colors), soil level, fabric type (sturdy cottons, easy care, delicates) and whether the fabric produces

lint (terry cloth, chenille) or collects lint (velveteen, corduroy). Wash lint producers such as cotton towels and socks separate from

lint collectors including synthetic garments and dress pants.

Loading the Washer

Load dry items loosely in the washer basket. For best results, load items evenly and loosely around the outside of the basket, filling in

towards the center on larger loads. To add items after washer has started, press Start/Pause if the lid is locked; wait until the Lid Lock

indicator on the display is no longer illuminated before attempting to open the lid. Lift the lid and submerge additional items around the

outside of the basket. Close the lid and press Start to resume. Adjust load size selection and/or use Deep Fill option if necessary.

NOTE: Some cycles use a two stage wash fill. The first stage will have a lower water level than the second stage; this is normal

operation.

WARNING

- Fire Hazard

Average Small Load

Clothes Level

Water Level

Average Medium Load

Clothes Level

Water Level

Clothes Level

Water Level

Average Large Load

Automatic Load Sensing

This determines the correct agitate profile, agitate duration and amount of water suited to the size and type of load placed in the

washer. The washer will not start the wash cycle or fill with water if the lid is open. When the lid is closed the machine is able to

begin filling with water in order to sense the load size.

NOTE: Automatic Load Sensing initiates a spin at the beginning of the cycle; this is normal operation.

NOTE: This is a high efficiency washing machine. This system requires less water while providing effective cleaning action. You

may notice that the water level is lower than on your previous washer. This is normal for a high efficiency washer.

Place laundry pretreatments, such as an Oxi product, directly in the bottom of the wash basket before loading clothes.

NOTE: Do not use liquid chlorine bleach and laundry pretreatments such as an Oxi product in the same wash load.

Pretreatment

Ŷ

Do not place large items such as

sheets, blankets and towels across

the Infusor. Load them around the

outside of the basket.

Ŷ

Do not put lawn or sofa cushions

into the washer as they are too big

to move. Remove outer covers and

ONLY wash them.

49-3000187 Rev. 1 17

Appliance communication

APPLIANCE COMMUNICATION

WiFi Connect (For customers in the United States only - on some models)

Depending on the model, your washer is either GE Appliances

WiFi Connect enabled, or compatible using the optional

GE Appliances U+ Connect module.

If enabled: Visit www.GEAppliances.com/connect and enter

your model number to show you the proper steps to connect

your appliance.

If compatible: To connect this appliance to the internet you

will need to purchase a GE Appliances U+ Connect module

and attach it to your appliance through the communication

port. The GE Appliances U+ Connect module will allow

your appliance to communicate with your smartphone for

remote appliance monitoring, control and notifications.

WiFi Connectivity: For assistance with the appliance

or the GE Appliances U+ Connect network connectivity,

please call GE Appliances Connected Home Support at

800.220.6899.

Please visit www.GEAppliances.com/connect to learn more

about connected appliance features, to learn what connected

appliance apps will work with your smartphone and to learn

where you can purchase a U+ Connect module.

The U+ Connect module has the FCC/IC ID located on the

back of the module.

Part Number Accessory

PBX23W00Y0 WiFi U+ Connect module

18 49-3000187 Rev. 1

Care and Cleaning

CARE AND CLEANING

Hoses connecting washer to faucet should be replaced every 5 years.

Water Supply Hoses

Ask the service technician to remove water

from drain pump and hoses. Do not store the

washer where it will be exposed to the weather.

GTW840 and GTW845 models only: Do not move the washer with a full tank of detergent. If moving the washer with a partially filled

tank of detergent, do not tilt washer forward as detergent could spill from tank. If moving the washer will result in tipping the washer

forward in any way, it is best to flush out your detergent tank. See Detergent Tank Clean-Out in this Care and Cleaning section.

Moving and Storage

Be sure water supply is shut off at faucets. Drain all water from hoses and water filter pump area if weather will be below freezing.

Long Vacations

Exterior of the Washer

Immediately wipe off any spills with a damp cloth.

Interior of the Washer

To clean the interior of the washer, select the Bulky Items

feature on the control panel. This Bulky Items cycle should be

performed, at a minimum, once per month. This cycle will use

more water, in addition to bleach, to control the rate at which

soils and detergents may accumulate in your washer.

NOTE: Read the instructions below completely before starting

the Bulky Items cycle.

1. Remove any garments or objects from the washer and

ensure the washer basket is empty.

2. Open the washer lid and pour one cup or 250 ml

of liquid bleach or other washing machine

cleaner into the basket.

3. Close the lid and select the Bulky Items cycle.

Push the Start button.

4. When the Bulky Items cycle is working, the display will show

the estimated cycle time remaining. Do not interrupt the cycle.

Bulky Items may be interrupted by pressing the Start button

in between cycles. A power outage in the house might also

interrupt the cycle. When the power supply is back, the Bulky

Items cycle resumes where it had stopped. When interrupted,

be sure to run a complete Bulky Items cycle before using the

washer. If the Power button is pressed during Bulky Items, the

cycle will be lost.

IMPORTANT:

Ŷ

Run Bulky Items with 1 Cup (250 ml) of bleach once a month.

Ŷ

After the completion of a Bulky Items cycle, the interior of

your washer may have a bleach smell.

Dispenser Drawer

After some period of use, a small amount of detergent or softener

residue may be present in the dispenser drawer. The drawer can

easily be removed for cleaning. To remove the drawer, pull it out

until the drawer stops and then lift up on the front of the drawer.

The drawer can then be removed from the dispenser box. Wash

the drawer in warm, soapy water using a mild detergent. Rinse

drawer with warm water. If siphon caps are removed for cleaning,

be sure to push siphon caps fully back into place after cleaning.

The dispenser drawer and siphon caps are not dishwasher

safe. The dispenser box is not removable, but it can be wiped

clean using a damp cloth if necessary. Do not attempt to

remove the dispenser box for cleaning.

Detergent Tank Clean-Out

(GTW840 and GTW845 models only)

NOTE: All clothes should be removed from the washer prior to

cleaning out the detergent tank.

To empty out the tank and remove any remaining detergent

from the reservoir:

1. Press and hold both the Detergent Dispense and Select

buttons for three seconds.

2. The empty out routine will begin with the contents of tank,

mixed with water, being dispensed into the basket and

consequently drained from the machine at the same time.

3. The empty out routine will continue for approximately 15

minutes unless it is paused by the pressing of the Start

button. If tank is initially full, routine may need to be run a

second time to empty detergent tank.

NOTE: Optionally, hot water can be added to the tank to aid in

flushing out the system of any residual detergent prior to starting

or during the cleanout routine.

GTW840 and GTW845 models

have a small dispenser drawer

with one compartment for

softener/conditioner only.

GTW720 and GTW725 models

have a large dispenser drawer

with compartments for both

detergent and softener.

MAX

Pretreatment

Water On Demand

Conditioner

Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing.

Service personnel – DO NOT contact the following parts while the appliance is energized: Drive Motor, Lid Lock,

Water Valves, Drain Pump and Recirculation Pump.

- Electrical Shock Hazard

WARNING

49-3000187 Rev. 1 19

Installation

Washer

Instructions

If you have any questions, call GE Appliances at 800.GE.CARES

(800.432.2737)

or visit our Website at: GEAppliances.com

In Canada, call 800.561.3344

or visit GEAppliances.ca

TOOLS REQUIRED FOR

WASHER INSTALLATION

Ŷ

Pliers

Ŷ

Level

PARTS SUPPLIED

PARTS REQUIRED (Sold separately)

GE Appliances Parts and Accessories

Order on-line at GEApplianceparts.com today, 24 hours a

day

or by phone at 800.626.2002 during normal business

hours.

Part Number Accessory

PM14X10002 4 ft Rubber Water Supply Hoses

Or

PM14X10005 4 ft Braided Metal Water Supply Hoses

WH1X2267 Rubber Washer (1) and Screen (1)

WH49X301

Drain Hose Extension (For discharge

heights from 60" - 96"

Ŷ

Drain Hose Extension (For discharge heights from 60" - 96"

NOTE: We strongly recommend the use of new water

supply hoses. Hoses degrade over time and need to

be replaced every 5 years to reduce the risk of hose

failures and water damage.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these

instructions for local inspector’s use.

•

IMPORTANT – Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these

instructions for future reference.

• Skill level – Installation of this appliance requires

basic mechanical and electrical skills.

• Completion time – 1-3 hours

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

Ŷ

Drain Hose

Ŷ

Cable Tie

Ŷ

Clamp

Ŷ

Drain Hose Clip

Ŷ

Owner's Reference Guide

Ŷ

Water Hoses (2)

Ŷ

Rubber Washers (2)

and Strainer Screens (2)

20 49-3000187 Rev. 1

Installation Instructions

LOCATION OF YOUR WASHER

DO NOT Install the Washer:

1. In an area exposed to dripping water or outside

weather conditions. The ambient temperature should

never be freezing or near freezing for proper washer

operation.

2. In an area where it will come in contact with curtains or

drapes.

3. On carpet. The floor MUST be a hard surface with a

PD[LPXPVORSHRIƎSHUIRRWFPSHUFP

To make sure the washer does not vibrate or move,

you may have to reinforce the floor.

NOTE:,IIORRULVLQSRRUFRQGLWLRQXVHƎLPSUHJQDWHG

plywood sheet solidly attached to existing floor covering.

IMPORTANT: Minimum Installation Clearances

- Alcove or Closet

• If your washer is approved for installation in an alcove or

closet, there will be a label on the back of the machine

describing requirements.

• Minimum clearance between washer and adjacent walls

or other surfaces: 0" either side, 2" front, 3" rear.

Vertical space from floor to overhead shelving, cabinets,

ceiling, etc. = 60".

• Closet doors must be louvered or otherwise ventilated

and have at least 60 square inches of open area. If the

closet contains both a washer and a dryer, doors must

contain a minimum of 120 square inches of

open area.

NOTE: The clearances stated on this label are minimums.

Consideration must be given to providing adequate

clearances for installing and servicing.

After the machine is in the home, remove outside

packing material/carton from washer.

Remove bag (containing clamp, cable tie and drain

hose clip), drain hose and Owner's Reference Guide

from tub.

NOTE: Leave foam shipping material inside tub

opening to hold tub in place during the rest of

installation.

1

UNPACKING THE WASHER

WATER SUPPLY REQUIREMENTS

WATER SUPPLY LINES - Purge Hot and Cold water supply lines for 30 seconds prior to installation of hoses and washing

machine. Ensure inlet hose screens are also clean and free of debris.

WATER PRESSURE - Must be 20 psi minimum to 120 psi maximum.

WATER TEMPERATURE - Household water heater should be set to deliver water at 120° to 150°F (50° to 66°C) TO THE

WASHER when hot wash is selected.

SHUTOFF VALVES - Both hot and cold shutoff valves (faucets) should be supplied.

DRAIN - Water should be drained into standpipe. Discharge height MUST NOT BE LESS THAN 30 INCHES, and no

more than 8 feet above the base of the washer. Standpipe must be 1-1/2 inches minimum inside diameter and must

be open to atmosphere.

Bag

Owner's Reference Guide

Leave foam shipping

material inside tub

Drain hose

Remove base from unit by placing foot on side of base

and tipping unit back on corner post. Remove base and

bring the washer back upright.

2

REMOVE THE BASE

Certain internal parts are intentionally not grounded

and may present a risk of electric shock only during

servicing.

Service personnel – DO NOT contact the following

parts while the appliance is energized: Drive Motor,

Lid Lock, Water Valves, Drain Pump and Recirculation

Pump.

- Electrical Shock Hazard

WARNING

La page charge ...

GE GTW720BPNDG Guide d'installation

GE GTW720BPNDG Guide d'installation

dans d''autres langues

Documents connexes

Autres documents