Candy CI 62 TP Manuel utilisateur

Catégorie
Plaques de cuisson
Taper
Manuel utilisateur
UK
Thank you for purchasing the CANDY induction hob. Please read this instruction manual
carefully before using the hob and keep it in a safe place for future reference.
ENGLISH
ITALIAN
SPANISH
POLISH
PORTUGUESE
Instruction Manual For Induction Hob
Manuale di istruzioni per piano cottura a
induzione
Manual de instrucciones para encimera de
inducción
Instrukcja uĪytkowania indukcyjnej páyty
grzejnej
Manual de Instruções da placa de indução
CI 62 TP
FRENCH
Table De Cuisson Induction
GERMAN
Gebrauchsanleitung für Induktions-Kochfeld
DUTCH
Gebruiksa
anwijzing inductiekookplaat
Safety Warnings
Your safety is important to us. Please read this
information before using your cooktop.
Installation
Electrical Shock Hazard
• Disconnect the appliance from the mains
electricity supply before carrying out any
work or maintenance on it.
• Connection to a good earth wiring system is
essential and mandatory.
• Alterations to the domestic wiring system
must only be made by a qualified electrician.
• Failure to follow this advice may result in
electrical shock or death.
Cut Hazard
• Take care - panel edges are sharp.
• Failure to use caution could result in injury or
cuts.
Important safety instructions
• Read these instructions carefully before
installing or using this appliance.
• No combustible material or products should be
placed on this appliance at any time.
• Please make this information available to the
person responsible for installing the appliance
EN-2
By placing the CE mark on this product, we are
confirming compliance to all relevant European safety, health
and environmental requirements which are applicable in
legislation for this product.
as it could reduce your installation costs.
• In order to avoid a hazard, this appliance must
be installed according to these instructions for
installation.
• This appliance is to be properly installed and
earthed only by a suitably qualified person.
• This appliance should be connected to a circuit
which incorporates an isolating switch
providing full disconnection from the power
supply.
• Failure to install the appliance correctly could
invalidate any warranty or liability claims.
Operation and maintenance
Electrical Shock Hazard
• Do not cook on a broken or cracked cooktop. If
the cooktop surface should break or
crack,switch the appliance off immediately at
the mains power supply (wall switch) and
contact a qualified technician.
• Switch the cooktop off at the wall before
cleaning or maintenance.
• Failure to follow this advice may result in
electrical shock or death.
Health Hazard
• This appliance complies with electromagnetic
safety standards.
• However, persons with cardiac pacemakers or
other electrical implants (such as insulin
EN-3
pumps) must consult with their doctor or
implant manufacturer before using this
appliance to make sure that their implants will
not be affected by the electromagnetic field.
• Failure to follow this advice may result in
death.
Hot Surface Hazard
• During use, accessible parts of this appliance
will become hot enough to cause burns.
• Do not let your body, clothing or any item
other than suitable cookware contact the
Induction glass until the surface is cool.
• Metallic objects such as knives, forks, spoons
and lids should not be placed on the hob surface
since they can get hot
• Keep children away.
• Handles of saucepans may be hot to touch.
Check saucepan handles do not overhang
other cooking zones that are on. Keep handles
out of reach of children.
• Failure to follow this advice could result in
burns and scalds.
Cut Hazard
• The razor-sharp blade of a cooktop scraper is
exposed when the safety cover is retracted.Use
with extreme care and always store safely and
out of reach of children.
• Failure to use caution could result in injury or
cuts.
Important safety instructions
• Never leave the appliance unattended when in
EN-4
use. Boilover causes smoking and greasy
spillovers that may ignite.
• Never use your appliance as a work or storage
surface.
• Never leave any objects or utensils on the
appliance.
• Do not place or leave any magnetisable
objects (e.g. credit cards, memory cards)or
electronic devices (e.g. computers, MP3 players)
near the appliance, as they may be affected by
its electromagnetic field.
• Never use your appliance for warming or
heating the room.
• After use, always turn off the cooking zones
and the cooktop as described in this manual (i.e.
by using the touch controls). Do not rely on the
pan detection feature to turn off the cooking
zones when you remove the pans.
• Do not allow children to play with the
appliance or sit, stand, or climb on it.
• Do not store items of interest to children in
cabinets above the appliance. Children climbing
on the cooktop could be seriously injured.
• Do not leave children alone or unattended in
the area where the appliance is in use.
• Children or persons with a disability which
limits their ability to use the appliance should
have a responsible and competent person to
instruct them in its use. The instructor should be
EN-5
satisfied that they can use the appliance without
danger to themselves or their surroundings.
• Do not repair or replace any part of the
appliance unless specifically recommended in
the manual. All other servicing should be done
by a qualified technician.
• Do not use a steam cleaner to clean your
cooktop.
• Do not place or drop heavy objects on your
cooktop.
• Do not stand on your cooktop.
• Do not use pans with jagged edges or drag
pans across the Induction glass surface as
this can scratch the glass.
• Do not use scourers or any other harsh
abrasive cleaning agents to clean your
cooktop, as these can scratch the Induction
glass.
• If the supply cord is damaged, it must be
replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a
hazard.
•This appliance is intended to be used in
household and similar applications such as:
-staff kitchen areas in shops, offices and other
working environments; -farm houses; -by
clients in hotels, motels and other residential
type environments ; -bed and breakfast type
environments.
•WARNING: The appliance and its accessible
parts become hot during use.
EN-6
Care should be taken to avoid touching heating
elements.
Children less than 8 years of age shall be kept
away unless continuously supervised.
•This appliance can be used by children aged
from 8 years and above and persons with
reduced physical,sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved.
•Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
•WARNING: Unattended cooking on a hob with
fat or oil can be dangerous and may result in
fire.NEVER try to extinguish a fire with water,
but switch off the appliance
and then cover flame e.g. with a lid or a fire
blanket.
•WARNING: Danger of fire: do not store items
on the cooking surfaces.
• Warning: If the surface is cracked, switch off
the appliance to avoid
the possibility of electric shock, for hob surfaces
of glass-ceramic or similar material which
protect live parts
•A steam cleaner is not to be used.
EN-7
8
•The appliance is not intended to be operated
by means of an external timer or separate
remote-control system.
Congratulations
on the purchase of your new Induction Hob.
We recommend that you spend some time to read this Instruction / Installation
Manual in order to fully understand how to install correctly and operate it.
For installation, please read the installation section.
Read all the safety instructions carefully before use and keep this Instruction /
Installation Manual for future reference.
Product Overview
Top View
Control Panel
1. max. 1800/2300 W zone
2. max. 1800/2300 W zone
3. max. 1200/1500 W zone
4. max. 2300/2600 W zone
5. max. 3000/3600 W zone
6. Glass plate
7. Control panel
1. Heating zone selection controls
2. Special function
3. Timer control
4. Power slider touch control
EN-8
7
4
6
1
5
2
3
9
A Word on Induction Cooking
Induction cooking is a safe, advanced, efficient, and economical cooking
technology. It works by electromagnetic vibrations generating heat directly in
the pan, rather than indirectly through heating the glass surface. The glass
becomes hot only because the pan eventually warms it up.
Before using your New Induction Hob
• Read this guide, taking special note of the ‘Safety Warnings’ section.
• Remove any protective film that may still be on your Induction hob.
Using the Touch Controls
• The controls respond to touch, so you don’t need to apply any pressure.
• Use the ball of your finger, not its tip.
• You will hear a beep each time a touch is registered.
• Make sure the controls are always clean, dry, and that there is no object (e.g.
a utensil or a cloth) covering them. Even a thin film of water may make the
controls difficult to operate.
iron pot
magnetic circuit
ceramic glass plate
induction coil
induced currents
EN-9
Choosing the right Cookware
• Only use cookware with a base suitable for induction
cooking. Look for the induction symbol on the
packaging or on the bottom of the pan.
• You can check whether your cookware is suitable by carrying out
a magnet test. Move a magnet towards the base of the pan. If it
is attracted, the pan is suitable for induction.
• If you do not have a magnet:
1. Put some water in the pan you want to check.
2. Follow the steps under ‘To start cooking’.
3. If does not flash in the display and the water is heating, the pan is suitable.
• Cookware made from the following materials is not suitable: pure stainless steel, aluminium or
copper without a magnetic base, glass, wood, porcelain, ceramic, and earthenware.
Do not use cookware with jagged edges or a curved base.
Make sure that the base of your pan is smooth, sits flat against the glass, and is
the same size as the cooking zone. Use pans whose diameter is as large as the
graphic of the zone selected.Using a pot a slightly wider energy will be used at
its maximum efficiency.If you use smaller pot efficiency could be less than
expected.Pot less than 140 mm could be undetected by the hob. Always centre
your pan on the cooking zone.
EN-10
Always lift pans off the Induction hob – do not slide, or they may scratch the
glass.
Using your Induction Hob
To start cooking
1. Touch the ON/OFF control.
After power on, the buzzer beeps once, all displays
show “ – “ or “ – – “, indicating that the induction
hob has entered the state of standby mode.
2. Place a suitable pan on the cooking zone that
you wish to use.
• Make sure the bottom of the pan and the surface
Of the cooking zone are clean and dry.
3. Touching the heating zone selection control ,
and a indicator next to the key will flash
4. Ajust heat setting by touching the the
slider control.
• If you don’t choose a heat setting within
EN-11
1 minute, the Induction hob will
automatically switch off. You will need to
start again at step 1.
• You can modify the heat setting at any time
during cooking.
If the display flashes alternately with the heat
setting
• you have not placed a pan on the correct cooking zone or,
• the pan you’re using is not suitable for induction cooking or,
• the pan is too small or not properly centered on the cooking zone.
No heating takes place unless there is a suitable pan on the cooking zone.
The display will automatically turn off after 2 minutes if no suitable pan is
placed on it.
When you have finished cooking
1. Touching the heating zone selection
control that you wish to switch off.
2. Turn the cooking zone off by touching the slider
to ” ”. Make sure the displayshows”0”.
3. Turn the whole cooktop off by touching the
ON/OFF control.
EN-12
4. Beware of hot surfaces
H will show which cooking zone is hot to touch. It will disappear when the
surface has cooled down to a safe temperature. It can also be used as an
energy saving function if you want to heat further pans, use the hotplate
that is still hot.
Using the Boost function
Actived the boost function
1. Touching the heating zone selection control
2. Touching the boost control “ ”,the zone indicator show “b” and the power
reach Max.
Cancel the Boost function
1. Touching the heating zone selection control
that you wish to cancel the boost function
EN-13
2. Touching the "Boost" control to cancel
the Boost function, then the cooking zone will
revert to its original setting.
• The cooking zone returns to its original setting after 5 minutes.
• If the original heat setting equals 0, it will return to 9 after 5 minutes.
• The 1
st
(2
nd
) heating zone can only reach the max power of 2 when the 2
nd
(1
st
) heating zone is Boost.
• The 3
nd
(4
st
) heating zone can only reach the max power of 2 when the 4
st
(3
nd
)
heating zone is Boost.
FLEXIBLE AREA
• This area can be used as a single zone or as two different zones, accordingly
to the cooking needs anytime.
• Free area is made of two independent inductors that can be controlled
separately.
As big zone
1. To activate the free area as a single big zone, simply press the
dedicated key.
2. Adjust heat setting by touching the slider control.
3. As a big zone, we suggest the used as the follow:
EN-14
Cookware: 250mm or 280mm diameter cookware (Square or Oval
cookware are acceptable)
We don’t recommend other operations except for above mentioned three
operations because it might effect the heating of appliance
As two independent zones
To use the flexible area as two different zones, you can have two choices of
heating.
(a) Put a pan on the right up side or the right down side of the flexible zone.
(b)Put two pans on both sides of the flexible zone.
Notice: Make sure the pan is bigger than 14cm.
EN-15
Locking the Controls
• You can lock the controls to prevent unintended use (for example children
accidentally turning the cooking zones on).
• When the controls are locked, all the controls except the ON/OFF control are
disabled.
To lock the controls
Touch the keylock control. The timer indicator will show “Lo“.
To unlock the controls
1. Make sure the Induction hob is turned on.
2. Touch and hold the keylock control for a while.
3. You can now start using your Induction hob.
When the hob is in the lock mode,all the controls are disable except the
ON/OFF
, you can always turn the induction hob off with the ON/OFF
control in an emergency,but you shall unlock the hob first in the next
operation
Special function
Keep Warm Function
You can use the function to keep the food warm.
The function can work in any cooking zone.
1. Touching the heating zone selection control
that you wish to use the warm function
2. Touching the "Warm function” control,
the indicator shows " ", then the
cooking zone starts warm function.
Keep Warm Function
EN-16
Over-Temperature Protection
A temperature sensor equipped can monitor the temperature inside the
Induction hob. When an excessive temperature is monitored, the Induction hob
will stop operation automatically.
Detection of Small Articles
When an unsuitable size or non-magnetic pan (e.g. aluminium), or some other
small item (e.g. knife, fork, key) has been left on the hob, the hob automatically
go on to standby in 1 minute. The fan will keep cooking down the induction hob
for a further 1 minute.
Auto Shutdown Protection
Auto shut down is a safety protection function for your induction hob. It shut
down automatically if ever you forget to turn off your cooking. The default
working times for various power levels are shown in the below table: .
Power level 1 2 3 4 5 6 7 8 9
Default working timer (hour)
8 8 8 4 4 4 2 2 2
When the pot is removed, the induction hob can stop heating immediately and
the hob automatically switch off after 2 minutes.
People with a heart pace maker should consult with their doctor before
using this unit.
Using the Timer
You can use the timer in two different ways:
• You can use it as a minute minder. In this case, it will not turn any cooking
zone off when the set time is up.
• You can set it to turn one or more cooking zones off after the set time is up.
• You can set the timer up to 99 minutes.
Using the Timer as a Minute Minder
If you are not selecting any cooking zone
1. Make sure the cooktop is turned on.
Note: you can use the minute minder even if you’re not selecting any
cooking zone.
Touch timer control or , the 10 will
show in the timer display.
EN-17
2. Set the time by touching the or control.
Hint: Touch the or control of the timer
once to decrease or increase by 1 minute.
Hold the or control of the timer to
decrease or increase by 10 minutes.
3. Set the time by touching the or control , now the timer you set is 95
minutes.
4. When the time is set, it will begin to count down immediately. The display will
show the remaining time
5.Buzzer will beep for 30 seconds and the timer
indicator shows “- - “ when the setting time finished.
Setting the timer to turn one or more cooking zones
off
If the timer is set on one zone:
1. Touching the heating zone selection control
that you want to set the timer for.
EN-18
2.Touch timer control or , the “10” will show in the
timer display.
3. Set the time by touching the or control.
Hint: Touch the or control of the timer
once to decrease or increase by 1 minute.
Hold the or control of the timer to
decrease or increase by 10 minutes.
4. set the time by touching the or control , now the timer you set is 95
minutes.
5. When the time is set, it will begin to count down immediately. The display will
show the remaining time
NOTE: The red dot next to power level indicator
will illuminate indicating that zone is selected.
6. When cooking timer expires, the corresponding
cooking zone will be switch off automatically.
Other cooking zone will keep operating if they are turned on previously.
EN-19
If the timer is set on more than one zone:
1. When you set the time for several cooking zones simultaneously, decimal
dots of the relevant cooking zones are on. The minute display shows the min.
timer. The dot of the corresponding zone flashes.
(set to 15 minutes)
(set to 30 minutes)
2. Once the countdown timer expires, the corresponding zone will switch off.
Then it will show the new min. timer and the dot of corresponding zone will flash.
• Touch the heating zone selection control, the corresponding timer will be
shown in the timer indicator.
Cancelled the timer
1. Touching the heating zone selection control
that you want to cancel the timer
2. Touch the and together to set the timer to ”00”, the timer is
cancelled,then the timer indicator shows “- - “ .
EN-20
1 / 1

Candy CI 62 TP Manuel utilisateur

Catégorie
Plaques de cuisson
Taper
Manuel utilisateur