Parkside 327520 Translation Of The Original Instructions

CORDLESS CHAIN SAW PKSA 20-Li A1

IAN 327523_1904

AKKU-KETTENSÄGE

Originalbetriebsanleitung

VOR GEBRAUCH SORGFÄLTIG LESEN UND FÜR

SPÄTEREN GEBRAUCH SICHER AUFBEWAHREN.

CORDLESS CHAIN SAW

Translation of the original instructions

READ CAREFULLY BEFORE USE AND STORE

SAFELY FOR LATER USE.

TRONÇONNEUSE SANS FIL

Traduction des instructions d’origine

À LIRE ATTENTIVEMENT AVANT L’USAGE ET À

CONSERVER EN VUE D’UN USAGE ULTÉRIEUR.

ACCU-KETTINGZAAG

Vertaling van de originele gebruiksaanwijzing

VOOR GEBRUIK ZORGVULDIG LEZEN EN VEILIG

OPBERGEN VOOR TOEKOMSTIG GEBRUIK.

GB / IE/NI Translation of the original instructions Page 1

FR / BE Traduction des instructions d’origine Page 27

NL / BE Vertaling van de originele gebruiksaanwijzing Pagina 53

DE / AT / CH Originalbetriebsanleitung Seite 79

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the

device.

Avant de lire le mode d'emploi, ouvrez les deux pages contenant les illustrations et familiarisez-vous

ensuite avec toutes les fonctions de l'appareil.

Vouw vóór het lezen de beide pagina‘s met de afbeeldingen open en maak u vertrouwd met alle functies

van het apparaat.

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

.375’’

(9.525mm)

.05’’(1.27mm)

A

B C

D

45° - 60°

1/4 3/4

A

B

C

D

E

F G

1

2

1

2

H

I

CB A

J

20V max.

18V

All Parkside tools and the chargers PLG 20 A1/PLG 20 A2/PLG 20 A3 of the X20V Team series

are compatible with the PAP 20 A1/PAP 20 A2/PAP 20 A3 battery pack.

Charging times

Charging currents

2 Ah

Battery pack

PAP 20 A1

3 Ah

Battery pack

PAP 20 A2

4 Ah

Battery pack

PAP 20 A3

max. 2.4 A

Charger PLG 20 A1

60 min

2,4 A

90 min

2,4 A

120 min

2,4 A

max. 3.5 A

Charger PLG 20 A2

60 min

2,4 A

60 min

3,5 A

80 min

3,5 A

max. 4.5 A

Charger PLG 20 A3

45 min

3,5 A

45 min

4,5 A

60 min

4,5 A

PKSA 20-Li A1

GB

│

IE

│

NI

│

1 ■

Contents

Introduction ......................2

Intended use ............................2

Hazard levels ...........................2

Features ...............................3

Package contents ........................3

Technical speciﬁcations ...................3

General power tool safety warnings . 5

1. Work area safety ......................5

2. Electrical safety .......................5

3. Personal safety ........................6

4. Power tool use and care ................6

5. Use and handling of the cordless

electrical power tool ..................7

6. Service ..............................7

Original accessories/auxiliary equipment .....7

Safety instructions for chainsaws ....8

General power tool safety warnings .........8

Precautions against kickback ...............9

Personal protective equipment (PPE) ....... 10

Storage and transportation .............. 10

Environmental safety. . . . . . . . . . . . . . . . . . . . 11

Vibrations ............................ 11

Safety guidelines for battery chargers ...... 11

Before use ......................12

Charging the battery pack (see ﬁg. A) ...... 13

Attaching/disconnecting the battery

pack to/from the tool ...................13

Checking the battery charge level ......... 13

Adding chain oil ....................... 13

Tightening and checking the saw chain ..... 14

Use ............................14

Switching on and oﬀ ................... 14

Checking and adjusting the chain lubrication 14

Checking the chain brake ................ 15

Basic working procedures when

felling trees .....................15

Preparing the kerf (see fold-out page, ﬁg. E) . 16

Branch removal ....................... 16

Working with wood that is under tension ....16

Kickback (see fold-out page, ﬁg. F) ........ 17

Drawing in (see fold-out page, ﬁg. G) ...... 17

Working safely ........................17

Cleaning and maintenance ........17

Cleaning the tool ...................... 17

Cleaning the chain drive ................ 18

Maintaining the chain lubrication .......... 18

Maintaining the guide rail ...............18

Fitting the guide rail and tensioning

the saw chain .........................18

Sharpening and caring for the saw chain . . . 19

Maintenance intervals ............20

Ordering replacement parts .......20

Storage and transportation ........21

Kompernass Handels GmbH

warranty .......................21

Service .........................22

Importer .......................22

Disposal ........................23

Translation of the original

Conformity Declaration ...........24

Ordering replacement batteries ....25

Telephone ordering .................... 25

PKSA 20-Li A1

■ 2

│

GB

│

IE

│

NI

CORDLESS CHAIN SAW

PKSA 20-Li A1

Introduction

Congratulations on the purchase of your new

tool. You have chosen a high-quality product.

The operating instructions are a part of this product.

They contain important information about safety,

usage and disposal. Before using the product, please

familiarise yourself with all of the operating and safety

instructions. Use the product only as described and

for the range of applications speciﬁed. Please also

pass these operating instructions on to any future

owner.

Intended use

The chainsaw may only be used for sawing wood

and for removing branches up to a max. Ø of

150 mm. The chainsaw may not be used for other

purposes.

Do not make any modiﬁcations to the chainsaw.

This can compromise safety.

The user/operator is liable for any resulting damage

or injuries of any kind and not the manufacturer.

Please note that this tool is not designed for com-

mercial use according to its intended purpose.

We accept no warranty liability if the tool is used

in commercial, manual trade or industrial opera-

tions or equivalent activities.

First-time users must seek training to familiarise

themselves with the characteristics of the tool.

For your safety, attend a state-approved chainsaw

training course.

Unauthorised operators:

People who are not familiar with these operating in-

structions, children, adolescents, and people under

the inﬂuence of alcohol, drugs or medications may

not operate this tool.

Hazard levels

DANGER!

► For an imminently dangerous situation which

will result in serious bodily injury or death.

WARNING!

► For a potentially dangerous situation which

could result in serious bodily injury or death.

CAUTION!

► Indicates a potentially hazardous situation

that can result in minor injury.

ATTENTION!

► Indicates a potentially hazardous situation

that can result in property damage.

PKSA 20-Li A1

GB

│

IE

│

NI

│

3 ■

Features

Front hand guard

Front handle

Chain oil tank cap

Safety lock-out

ON/OFF switch

Rear handle

Bumper spike (pre-assembled)

Guide rail (pre-assembled)

Saw chain (pre-assembled)

Grinder support

Fixing screw

Chain tensioning ring

Sprocket cover

Battery charge level button

Battery display LED

Battery pack*

Release button for the battery pack

Oil dispenser

Chain sprocket

Slotted hole in the guide rail

Blade guide

High-speed battery charger*

Red charge control LED

Green charge control LED

Cover for the guide rail (chain guard)

Organic chain oil

Package contents

1 cordless chain saw

1 Oregon 10" saw chain 91P040X

(pre-assembled)

1 Oregon 10" guide rail 100NDEA041

(pre-assembled)

1 cover for the guide rail (chain guard)

180 ml organic chain oil (Made in Germany)

1 set of operating instructions

Technical speciﬁcations

Cordless chain saw

Nominal voltage: 20 V

(DC)

Idle speed: 2,900rpm

Max. chain speed: 5.6 m/s

Oil tank capacity: approx. 275 ml

Guide rail: Oregon 10"

100NDEA041

Saw chain: Oregon 10" 91P040X

Chain pitch: 0,375" (9,525 mm)

Drive link thickness: 1.27 mm (0.050")

Number of teeth on the

chain sprocket: 6

Length of the guide rail: 305 mm

Usable cut length/guide

rail 230 mm

Battery: PAP 20 A3*

Type: LITHIUM ION

Rated voltage: 20 V

(DC)

Capacity: 4 Ah (80Wh)

Cells: 10

High-speed battery charger: PLG 20 A3*

INPUT:

Rated voltage: 230–240 V

~

, 50 Hz

(AC)

Rated power

consumption: 120 W

Fuse (internal): 3.15 A

T3.15A

OUTPUT:

Rated voltage: 21.5 V

(DC)

Rated current: 4.5 A

Charging time: approx. 60 min

Protection class: II / (double insulation)

*BATTERY AND CHARGER ARE NOT INCLUDED

PKSA 20-Li A1

■ 4

│

GB

│

IE

│

NI

Noise emission value:

Noise measurement value determined in accordance

with EN 60745-2-13. The A-rated noise level of

the power tool is typically:

Sound pressure level: L

pA

= 86.3 dB (A)

(at operator position)

Uncertainty K: K

pA

= 3 dB

Sound power level: L

WA

= 94.7 dB (A)

Uncertainty K: K

WA

= 2.6 dB

Guaranteed sound

power level: L

WA

= 97 dB (A)

(according to 2000/14/EC

amended by 2005/88/EC)

Wear ear muﬀs!

Total vibration value:

Total vibration values (vector total of three directions)

determined in accordance with EN 60745-2-13:

Vibration at the handle:

a

h

= 7.3 m/s

2

, K = 1.5 m/s

2

WARNING!

► The vibration level varies depending on the

use of the power tool and may be higher

than the value speciﬁed in these instructions

in some cases. Regular use of the power tool

in this way may cause the user to underesti-

mate the vibration. Try to keep the vibration

loads as low as possible. Measures to reduce

the vibration load are, e.g. wearing gloves

and limiting the working time. Wherein all

states of operation must be included (e.g.

times when the power tool is switched oﬀ and

times where the power tool is switched on but

running without load).

NOTE

► The vibration level speciﬁed in these instruc-

tions has been measured in accordance

with the standardised measuring procedure

speciﬁed in EN 60745 and can be used to

make equipment comparisons. The speciﬁed

vibration emission value can also be used to

make an initial exposure estimate.

WARNING!

► You can reduce the vibration risk, for example,

the risk of Raynaud's phenomenon (circulatory

problems), by taking regular breaks during

which you rub your hands together.

The following symbols are used in these

operating instructions/on the tool:

Read these operating instructions

thoroughly before using the tool for

the ﬁrst time, and retain them for

future reference.

Warning! Read the operating

instructions before use!

WARNING! Special safety precau-

tions are required when working

with the chainsaw.

Read and observe all warnings!

Wear snugly ﬁtting protective

clothing with a cut-resistant lining.

Wear a hard hat!

Wear safety goggles!

Wear ear muﬀs!

Wear protective gloves!

Wear non-slip safety shoes!

PKSA 20-Li A1

GB

│

IE

│

NI

│

5 ■

WARNING! Risk of kickback.

Protect yourself from kickback from

the chainsaw and avoid all contact

with the rail tip.

WARNING! Risk of kickback!

Do not saw with the tip of the blade.

Always operate the chainsaw with

both hands.

Do not work with the chainsaw in

one hand.

Beware of ﬂying objects!

Attention! Risk of injury from sharp

blades.

Protect the tool from rain and

moisture!

Before performing any maintenance

work, turn oﬀ the tool and discon-

nect the battery!

Guaranteed sound power level of

the tool

Block and unblock the chain brake

Running direction of the chain

Guide rail length

General power tool

safety warnings

WARNING!

► Read all safety warnings and all

instructions. Failure to follow the

warnings and instructions may result

in electric shock, ﬁre and/or serious

injury.

Save all warnings and instructions for future

reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmos-

pheres, such as in the presence of ﬂammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

PKSA 20-Li A1

■ 6

│

GB

│

IE

│

NI

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the inﬂuence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b) Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat,

or hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch

is in the oﬀ-position before connecting to power

source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your

ﬁnger on the switch or energising power tools that

have the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that can-

not be controlled with the switch is dangerous

and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are dan-

gerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may aﬀect the

power tool’s operation. If damaged, have

the power tool repaired before use. Many

accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations diﬀerent from those

intended could result in a hazardous situation.

PKSA 20-Li A1

GB

│

IE

│

NI

│

7 ■

5. Use and handling of the cordless

electrical power tool

a) Charge a rechargeable battery unit using

only the charger recommended by the manu-

facturer. Chargers are often designed for a

particular type of rechargeable battery unit.

There is the danger of ﬁre if other types of re-

chargeable battery units are used.

b) Only the rechargeable battery units supplied

are to be used with an electrical power tool.

The use of other rechargeable battery units may

lead to the danger of injury or ﬁre.

c) When they are not being used, store re-

chargeable battery units away from paper-

clips, coins, keys, nails, screws or other small

metal objects that could cause the contacts

to be bridged. Short-circuiting the contacts of

a rechargeable battery unit may result in heat

damage or ﬁre.

d) Fluids may leak out of rechargeable battery

units if they are misused. If this happens,

avoid contact with the ﬂuid. If contact occurs,

ﬂush the aﬀected area with water. Seek addi-

tional medical help if any of the ﬂuid gets into

your eyes. Escaping battery ﬂuid may cause

skin irritation or burns.

CAUTION! RISK OF EXPLOSION!

Never charge non-rechargeable

batteries.

Protect the rechargeable battery

from heat (for example, from continu-

ous exposure to sunlight), ﬁre, water

and moisture. There is a risk of explo-

sion.

6. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

b) Never try to repair damaged batteries. Batter-

ies should only be maintained by the manufac-

turer or an approved customer service centre.

Original accessories/auxiliary

equipment

■ Use only the accessories and additional equip-

ment speciﬁed in the operating instructions and

which are compatible with the tool.

WARNING!

■ Do not use any accessories that are not

recommended by PARKSIDE. This can lead to

an electric shock and ﬁre.

PKSA 20-Li A1

■ 8

│

GB

│

IE

│

NI

Safety instructions for

chainsaws

IMPORTANT!

READ CAREFULLY BEFORE USE

AND STORE SAFELY FOR LATER

USE.

General power tool safety warnings

WARNING!

► Stay alert, watch what you are doing and

use common sense when operating the

tool. Do not use the tool while you are

ill, tired or under the inﬂuence of drugs,

alcohol or medication.

A moment of inattention while operating the

tool may result in serious personal injury.

► Avoid improper use. Use the machine only

as described under "Intended use".

■ Keep all body parts away from the saw chain

while the saw is running. Before starting the

saw, make sure that the saw chain is not touch-

ing anything. When working with a chainsaw, a

moment of inattentiveness can lead to clothing or

body parts getting caught in the saw chain.

■ Always hold the chainsaw with your right

hand on the rear handle and your left hand

on the front handle. Holding the chainsaw in

an inverted working posture increases the risk

of injuries and is prohibited.

■ Hold the power tool only by the insulated

gripping surfaces because the saw chain can

come into contact with hidden cables. Saw

chains touching a live wire make metal parts of

the power tool live and could cause an electric

shock to the operator.

■ Wear protective goggles and ear muﬀs.

Additional protective equipment for your

head, hands, legs and feet is recommended.

Suitable protective clothing reduces the risk of

injury from ﬂying chips and accidental contact

with the saw chain.

■ Do not use the chainsaw in a tree. When

working in a tree, there is a risk of injury.

■ Make sure you have ﬁrm footing and use the

chainsaw only when standing on ﬁrm, safe

and level ground. Slippery ground or unstable

standing surfaces (e.g. on a step ladder) can

lead to a loss of balance or loss of control of

the chainsaw.

■ When sawing a branch that is under tension,

be prepared for it to spring back. Once the

tension in the wooden ﬁbres is released, the

branch can hit the operator and/or knock the

chainsaw out of his hands.

■ Be extremely careful when cutting brushwood

and young trees. The thin material can catch in

the saw chain and ﬂy in your direction or knock

you oﬀ balance.

■ Carry the chainsaw by the front handle when

switched oﬀ, with the saw chain facing away

from your body. When transporting or storing

the chainsaw, always put on the protective

cover. Careful handling of the chainsaw reduc-

es the probability of accidental contact with the

running saw chain.

■ Follow the instructions for lubrication, chain

tension and changing accessories. An incor-

rectly tensioned or lubricated chain can break

or increase the risk of kickback.

■ Keep the handles dry, clean and free from oil

and grease. Greasy, oily handles are slippery

and result in loss of control.

■ Saw wood only. Do not use the chainsaw for

work for which it is not intended. For example:

do not use the chainsaw to saw plastic,

masonry, or construction materials that are

not made of wood. Using the chainsaw for

work other than that for which it was intended

can lead to hazardous situations.

■ Start the cut using full power and keep the

chainsaw at top speed while sawing.

■ Ensure that there are no objects on the ground

that you can trip over.

■ Before using the tool for the ﬁrst time, read the

operating instructions and pay close attention

to the safety instructions.

PKSA 20-Li A1

GB

│

IE

│

NI

│

9 ■

■ The warning and safety signs on the tool pro-

vide important information for safe operation.

■ In addition to the notices in these operating

instructions, all general safety and accident pre-

vention legislation must also be complied with.

■ Keep plastic wrapping away from children.

There is a risk of suﬀocation!

■ Insuﬃciently informed operators can be a

danger to other people and themselves due to

improper use. The operator is responsible for

third parties.

■ Be very careful when handling the tool. Use

common sense when working and play close

attention to what you are doing.

■ Do not work for longer than 10 minutes in one

session. We recommend taking a break of

10–20 minutes between working sessions.

■ Lend the tool only to users who have experi-

ence with the tool. Hand over the operating

instructions at the same time.

■ Some cutting tasks require special training and

particular skills. If in doubt, please consult an

expert.

■ First-time users must seek training to familiarise

themselves with the characteristics of the tool.

For your safety, attend a state-approved chain-

saw training course.

■ When not in use, the tool must be secured to

ensure that it is not a risk to anyone else.

Secure against unauthorised access.

■ The user of the tool is responsible for all acci-

dents and risks that cause injury or damage to

other people's property.

■ Children, adolescents and people with reduced

physical, sensory or mental capabilities must

not use the chainsaw. The only exception to this

are young people over the age of 16 who are

being trained by a specialist.

■ Note that improper maintenance, the use of

non-approved spare parts, or the removal or

modiﬁcation of the safety equipment can lead

to damage to the tool and severe injuries to the

operator.

Precautions against kickback

WARNING! KICKBACK!

► Be aware of the danger of kickback when

working with the tool. There is a risk of personal

injury. You can avoid kickbacks by being care-

ful and using the correct sawing technique.

■ Contact with the tip of the rail can, in some

cases, lead to an unexpected rearwards reac-

tion resulting in the guide rail ﬂying upwards

towards the operator (see ﬁg. A).

Fig. A

■ Kickbacks can occur if the tip of the guide rail

touches an object or if the wood bends and the

saw chain gets caught in the cut.

■ If the saw chain jams in the upper edge of the

guide rail, the chainsaw can kick back violently

towards the operator (see fold-out page, ﬁg. F).

■ If the saw chain jams in the lower edge of the

guide rail, the chainsaw can jerk violently away

from the operator (see fold-out page, ﬁg. G).

■ Be extremely careful when reapplying the chain

of the chainsaw to a cut you have already

started.

■ Do not saw any branches or pieces of wood

that can move their position during sawing or in

which the cut could close during sawing.

■ Any such reaction can lead to you losing control

over the saw and possibly injuring yourself. Do

not rely solely on the chainsaw's built-in safety

devices. As the user of a chainsaw, you can

take a number of measures to avoid accidents

and injury. A kickback is caused by incorrect

use or misuse. It can be avoided by taking

suitable precautions (as given below):

Bild 1

PKSA 20-Li A1

■ 10

│

GB

│

IE

│

NI

■ Hold the saw ﬁrmly with both hands, with

your thumb and ﬁngers around the handles of

the chainsaw. Position your body and arms so

you can withstand kickback forces. If suitable

measures are taken, the operator can control

the kickback forces. Never let go of the chain-

saw (see fold-out page, ﬁg. C).

■ Avoid an abnormal posture and do not saw

over shoulder height. This will prevent inadvert-

ent contact with the tip of the rail and allows a

better control of the chainsaw in unexpected

situations.

■ Always use the replacement rails and saw

chains speciﬁed by the manufacturer. Incorrect

replacement rails and saw chains can lead to a

breakage of the saw chain and/or kickback.

■ Follow the manufacturer's instructions for

sharpening and maintaining the saw chain.

Setting the depth stop too low can increase the

risk of kickback.

■ Do not saw with the tip of the blade. This can

lead to a kickback.

■ Make sure that are no nails or pieces of metal

in the cutting area. Pay particular attention

to nails or pieces of iron in the area of the cut.

Also be careful when cutting hardwoods in

which the chain could jam. This can lead to a

kickback.

Personal protective equipment (PPE)

DANGER!

► Wear personal protective equipment (PPE)!

–

Wear a hard hat with a visor or safety

goggles and ear muﬀs.

– Wear snugly ﬁtting protective clothing

with a cut-resistant lining.

–

Wear non-slip safety shoes!

–

Wear protective gloves!

■ Avoid loose-ﬁtting clothing that can get caught.

■ Do not wear a scarf, tie or any jewellery!

■ If you have long hair, wear a hairnet!

■ Always wear a helmet when working in wooded

areas. This oﬀers protection from falling branches.

Check the helmet regularly for damage.

Replace it after 5 years at most.

Use only approved protective helmets.

■ The face shield/safety goggles protect the user

from wood chips and splinters.

To prevent eye injuries, always use a face shield

or safety goggles while working with the tool.

■ Always wear ear muﬀs.

The noise produced by the tool can damage

your hearing.

■ Wear robust protective gloves made of a durable

material, e.g. leather.

■ Wear a dust mask when sawing dry wood.

Sawing can generate sawdust.

Storage and transportation

■ Switch oﬀ the chainsaw before moving it any-

where, even short distances.

Engage the chain brake and put on the chain

guard.

■ Always use the chain guard for transportation

and storage (see fold-out page, ﬁg. I).

■ Protect the machine during transport (also in

vehicles) against tipping over to prevent dam-

age or injuries.

■ Carry the tool by the front handle only. Make

sure the guide rail is facing to the rear, away

from your body (see fold-out page, ﬁg. I).

■ Clean and maintain the chainsaw before storage.

■ Store the tool in a secure and dry location.

Secure it against unauthorised access.

PKSA 20-Li A1

GB

│

IE

│

NI

│

11 ■

Environmental safety

■ Work only in daylight.

■ Do not work in inopportune weather conditions,

such as rain or wind.

This will lead to an increased risk of accidents.

■ Keep your work area clean and tidy.

■ Keep children, other people and animals at a

distance before and during the work.

Distractions can cause you to lose control.

■ Before starting work, ensure that no people,

animals or valuable property are inside the

danger zone.

■ Do not work in the vicinity of wire fences or

areas with loose old wire.

Vibrations

WARNING!

► You can reduce the vibration risk, for exam-

ple, the risk of Raynaud's phenomenon (cir-

culatory problems), by taking regular breaks

during which you rub your hands together.

■ Always wear protective gloves and ensure your

hands are warm.

■ Make sure that the chain is always sharp.

■ Take regular work breaks.

Safety guidelines for battery chargers

■ This tool may be used by children

aged 8 years and above and by

persons with limited physical, senso-

ry or mental capabilities or lack of

experience and knowledge, provid-

ed that they are under supervision

or have been told how to use the

tool safely and are aware of the po-

tential risks. Do not allow children

to use the tool as a toy. Cleaning

and user maintenance tasks may

not be carried out by children un-

less they are supervised.

■ To avoid potential risks, damaged

mains cables should be replaced

by the manufacturer, their customer

service department or a similarly

qualiﬁed person.

The charger is suitable for indoor use

only.

WARNING!

■ To avoid potential risks, damaged mains

cables should be replaced by the manufac-

turer, their customer service department or a

similarly qualiﬁed person.

ATTENTION!

♦ This charger can only charge the following bat-

teries: PAP 20 A1 / PAP 20 A2 / PAP 20 A3.

♦ A current list of battery compatibility can be

found at www.Lidl.de/Akku.

PKSA 20-Li A1

■ 12

│

GB

│

IE

│

NI

Before use

RISK OF INJURY!

► Always switch the tool oﬀ and remove the bat-

tery before carrying out any work on the tool.

WARNING!

► Always carry out checks before use and with

the tool switched oﬀ.

► Check that the tool is in good working order

before every use and after it has been

dropped.

► Check whether moving parts work properly.

Many accidents are caused by poorly main-

tained tools.

Have any damage repaired by qualiﬁed

specialists.

► Use the chainsaw and accessories only as

described in these instructions, taking into

account the working conditions and the work

to be performed.

Using machine tools for purposes diﬀerent

from those intended could result in a hazard-

ous situation.

■ Check the chain brake is in good working order

regularly (front hand guard, see fold-out page,

ﬁg. B).

■ Check that the guide rail is correctly ﬁtted.

■ Check that the saw chain is correctly tensioned.

Follow the instructions for lubrication, chain

tension and changing accessories. An incorrectly

tensioned or lubricated chain can break or

increase the risk of kickback.

■ Keep cutting tools sharp and clean. Sharpen

them regularly and replace worn parts prompt-

ly. Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

■ Check the throttle control and the throttle control

lock for freedom of movement. The throttle con-

trol must spring back into the start position.

■ Check whether the handles are clean, dry and

free of oil and dirt.

■ Never carry out the work alone. In case of

emergency, someone should be close by.

■ Use the chainsaw only if you are standing on

ﬁrm, safe and even ground.

Do not overreach.

Slippery ground or unstable standing surfaces

(e.g. on a step ladder) can lead to a loss of

balance or loss of control of the chainsaw.

Keep proper footing and balance at all times.

This enables better control of the chainsaw in

unexpected situations.

■ Do not use the chainsaw in a tree. When working

in a tree there is a risk of injury.

■ Never saw above shoulder height.

■ Always hold the chainsaw with your right hand

on the rear handle and your left hand on the

front handle (see fold-out, page ﬁg. C). Holding

the chainsaw in an inverted working posture

increases the risk of injuries and is prohibited.

■ When the chainsaw is running, keep all body

parts away from the saw chain. Before starting

the chainsaw, make sure that the saw chain is

not touching anything. When working with a

chainsaw, a moment of inattentiveness can lead

to clothing or body parts getting caught in the

saw chain.

■ Switch the chainsaw oﬀ immediately if you no-

tice any changes in the way the tool behaves.

■ If the chainsaw hits a stone, nails or other hard

objects, stop the motor immediately and check

the saw chain and the guide rail for damage.

PKSA 20-Li A1

GB

│

IE

│

NI

│

13 ■

■ Do not drop the chainsaw, knock it against ob-

structions and do not use the guide rail as a lever.

■ Use the chainsaw only for sawing wood.

■ When sawing a branch that is under tension, be

prepared for it to spring back. Once the tension

in the wooden ﬁbres is released, the branch can

hit the operator and/or knock the chainsaw out

of his hands.

■ Be extremely careful when cutting brushwood

and young trees. The thin material can catch in

the saw chain and ﬂy in your direction or knock

you oﬀ balance.

Charging the battery pack (see ﬁg. A)

CAUTION!

► Always unplug the tool before you remove

the battery pack from or connect the battery

pack to the charger.

NOTE

► Never charge the battery pack at an ambient

temperature of below 10°C or above 40°C.

If a lithium-ion battery is to be stored for an

extended period, the charge level should be

checked regularly. The optimum charge level

is between 50% and 80%. The storage

climate should be cool and dry and the

ambient temperature should be between 0°C

and 50°C.

♦ Connect the battery pack

to the high-speed

battery charger

(see ﬁg. A).

♦ Insert the power plug into the socket.

The charge control LED

lights up red.

♦ The green charge control LED

indicates that

the charging process is complete and the bat-

tery pack is ready for use.

ATTENTION!

♦ If the red charge control LED

ﬂashes, this

means that the battery pack has overheat-

ed and cannot be charged.

♦ If the red and green charge control LEDs

both ﬂash, this means that the battery

pack is defective.

♦ Switch oﬀ the charger for at least 15 minutes

between successive charging sessions. Also

disconnect the power plug from the mains

power socket.

Attaching/disconnecting the battery

pack to/from the tool

Attaching the battery pack:

♦ Push the battery pack

into the handle until

it clicks into place.

Removing the battery pack:

♦ Press the release button

and remove the

battery pack.

Checking the battery charge level

♦ Press the battery charge level button to

check the status of the battery (see also main

diagram).

The status/remaining charge will be shown on

the battery display LED

as follows:

♦ RED/ORANGE/GREEN = maximum charge

RED / ORANGE = medium charge

RED = low charge – charge the battery

Adding chain oil

WARNING!

► Always check the chain lubrication before

starting work.

► Never work without chain lubrication!

If the saw chain runs dry, the cutting equip-

ment may become irreparably damaged in a

short time.

NOTE

► Use only saw chain oil, preferably biode-

gradable. Do not use waste oil, motor oil, etc.

► While working, check whether the chain

lubrication is working correctly.

PKSA 20-Li A1

■ 14

│

GB

│

IE

│

NI

♦ Always clean the area around the chain oil tank

cap

before ﬁlling to prevent dirt getting into

the chain oil tank.

Use a dry, lint-free cloth to do this.

♦ Turn the chain oil tank cap

anticlockwise

and remove it.

The chain oil tank cap

is connected to the

chain oil tank with an loss-prevention device

and cannot fall onto the ﬂoor.

♦ Add the supplied organic chain oil

to the

chain oil tank.

Do not spill any chain oil while ﬁlling the chain

oil tank and do not ﬁll the tank to overﬂowing.

♦ Wipe up any spilt chain oil immediately.

♦ Turn the chain oil tank cap

clockwise to

close it.

Tightening and checking the saw chain

WARNING!

► Wear protective gloves! There is a risk of

injury from the sharp cutting teeth!

► Check the chain tension before every use.

♦ Undo the ﬁxing screw

.

♦ Turn the chain tensioning ring

in a clockwise

direction to increase the tension.

♦ The saw chain

must lie against the underside

of the blade.

Check whether the saw chain (with the chain

brake oﬀ, pull the front hand guard to the rear)

can be drawn by hand over the guide rail .

♦ Now tighten the ﬁxing screw completely.

NOTE

► A new saw chain

stretches and must be

tightened more often.

Use

Before starting the tool, always check that:

■ The protective equipment and cutting equipment

is complete and in perfect working order.

■ All screw connections are ﬁrmly tightened.

■ All moving parts can move smoothly and freely.

Switching on and oﬀ

Switching on:

♦ Press the safety lock-out and keep it pressed

and then press the ON/OFF switch

.

♦ After starting, the safety lock-out

can be

released again.

Switching oﬀ:

♦ Release the ON/OFF switch

.

Optimal working procedures

Get to know the chainsaw before you start to use it.

Checking and adjusting the chain

lubrication

ATTENTION!

► Never work without chain lubrication!

If the saw chain runs dry, the cutting equip-

ment may become irreparably damaged in a

short time.

► Always check the chain lubrication before

starting work.

NOTE

► Use only saw chain oil, preferably biode-

gradable. Do not use waste oil, motor oil, etc.

► While working, check whether the chain

lubrication is working correctly.

♦ With the chainsaw running, hold it over a sawn

oﬀ tree stump or a suitable ground sheet.

If the lubrication is adequate, a light ﬁlm of oil

forms on the tree stump or the ground sheet

(see fold-out page, ﬁg. D).

La page charge ...

Parkside 327520 Translation Of The Original Instructions

Ce manuel convient également à

Parkside 327520 Translation Of The Original Instructions

dans d''autres langues

Documents connexes

Autres documents