Parkside 327520 Translation Of The Original Instructions

Catégorie
Tronçonneuses électriques
Taper
Translation Of The Original Instructions

Ce manuel convient également à

CORDLESS CHAIN SAW PKSA 20-Li A1
IAN 327523_1904
AKKU-KETTENSÄGE
Originalbetriebsanleitung
VOR GEBRAUCH SORGFÄLTIG LESEN UND FÜR
SPÄTEREN GEBRAUCH SICHER AUFBEWAHREN.
CORDLESS CHAIN SAW
Translation of the original instructions
READ CAREFULLY BEFORE USE AND STORE
SAFELY FOR LATER USE.
TRONÇONNEUSE SANS FIL
Traduction des instructions d’origine
À LIRE ATTENTIVEMENT AVANT L’USAGE ET À
CONSERVER EN VUE D’UN USAGE ULTÉRIEUR.
ACCU-KETTINGZAAG
Vertaling van de originele gebruiksaanwijzing
VOOR GEBRUIK ZORGVULDIG LEZEN EN VEILIG
OPBERGEN VOOR TOEKOMSTIG GEBRUIK.
GB / IE/NI Translation of the original instructions Page 1
FR / BE Traduction des instructions d’origine Page 27
NL / BE Vertaling van de originele gebruiksaanwijzing Pagina 53
DE / AT / CH Originalbetriebsanleitung Seite 79
Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the
device.
Avant de lire le mode d'emploi, ouvrez les deux pages contenant les illustrations et familiarisez-vous
ensuite avec toutes les fonctions de l'appareil.
Vouw vóór het lezen de beide pagina‘s met de afbeeldingen open en maak u vertrouwd met alle functies
van het apparaat.
Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend
mit allen Funktionen des Gerätes vertraut.
.375’’
(9.525mm)
.05’’(1.27mm)
A
B C
D
45° - 60°
1/4 3/4
A
B
C
D
E
F G
1
2
1
2
H
I
CB A
J
20V max.
18V
All Parkside tools and the chargers PLG 20 A1/PLG 20 A2/PLG 20 A3 of the X20V Team series
are compatible with the PAP 20 A1/PAP 20 A2/PAP 20 A3 battery pack.
Charging times
Charging currents
2 Ah
Battery pack
PAP 20 A1
3 Ah
Battery pack
PAP 20 A2
4 Ah
Battery pack
PAP 20 A3
max. 2.4 A
Charger PLG 20 A1
60 min
2,4 A
90 min
2,4 A
120 min
2,4 A
max. 3.5 A
Charger PLG 20 A2
60 min
2,4 A
60 min
3,5 A
80 min
3,5 A
max. 4.5 A
Charger PLG 20 A3
45 min
3,5 A
45 min
4,5 A
60 min
4,5 A
PKSA 20-Li A1
GB
IE
NI
 1
Contents
Introduction ......................2
Intended use ............................2
Hazard levels ...........................2
Features ...............................3
Package contents ........................3
Technical specifications ...................3
General power tool safety warnings . 5
1. Work area safety ......................5
2. Electrical safety .......................5
3. Personal safety ........................6
4. Power tool use and care ................6
5. Use and handling of the cordless
electrical power tool ..................7
6. Service ..............................7
Original accessories/auxiliary equipment .....7
Safety instructions for chainsaws ....8
General power tool safety warnings .........8
Precautions against kickback ...............9
Personal protective equipment (PPE) ....... 10
Storage and transportation .............. 10
Environmental safety. . . . . . . . . . . . . . . . . . . . 11
Vibrations ............................ 11
Safety guidelines for battery chargers ...... 11
Before use ......................12
Charging the battery pack (see fig. A) ...... 13
Attaching/disconnecting the battery
pack to/from the tool ...................13
Checking the battery charge level ......... 13
Adding chain oil ....................... 13
Tightening and checking the saw chain ..... 14
Use ............................14
Switching on and off ................... 14
Checking and adjusting the chain lubrication 14
Checking the chain brake ................ 15
Basic working procedures when
felling trees .....................15
Preparing the kerf (see fold-out page, fig. E) . 16
Branch removal ....................... 16
Working with wood that is under tension ....16
Kickback (see fold-out page, fig. F) ........ 17
Drawing in (see fold-out page, fig. G) ...... 17
Working safely ........................17
Cleaning and maintenance ........17
Cleaning the tool ...................... 17
Cleaning the chain drive ................ 18
Maintaining the chain lubrication .......... 18
Maintaining the guide rail ...............18
Fitting the guide rail and tensioning
the saw chain .........................18
Sharpening and caring for the saw chain . . . 19
Maintenance intervals ............20
Ordering replacement parts .......20
Storage and transportation ........21
Kompernass Handels GmbH
warranty .......................21
Service .........................22
Importer .......................22
Disposal ........................23
Translation of the original
Conformity Declaration ...........24
Ordering replacement batteries ....25
Telephone ordering .................... 25
PKSA 20-Li A1
2 
GB
IE
NI
CORDLESS CHAIN SAW
PKSA 20-Li A1
Introduction
Congratulations on the purchase of your new
tool. You have chosen a high-quality product.
The operating instructions are a part of this product.
They contain important information about safety,
usage and disposal. Before using the product, please
familiarise yourself with all of the operating and safety
instructions. Use the product only as described and
for the range of applications specified. Please also
pass these operating instructions on to any future
owner.
Intended use
The chainsaw may only be used for sawing wood
and for removing branches up to a max. Ø of
150 mm. The chainsaw may not be used for other
purposes.
Do not make any modifications to the chainsaw.
This can compromise safety.
The user/operator is liable for any resulting damage
or injuries of any kind and not the manufacturer.
Please note that this tool is not designed for com-
mercial use according to its intended purpose.
We accept no warranty liability if the tool is used
in commercial, manual trade or industrial opera-
tions or equivalent activities.
First-time users must seek training to familiarise
themselves with the characteristics of the tool.
For your safety, attend a state-approved chainsaw
training course.
Unauthorised operators:
People who are not familiar with these operating in-
structions, children, adolescents, and people under
the influence of alcohol, drugs or medications may
not operate this tool.
Hazard levels
DANGER!
For an imminently dangerous situation which
will result in serious bodily injury or death.
WARNING!
For a potentially dangerous situation which
could result in serious bodily injury or death.
CAUTION!
Indicates a potentially hazardous situation
that can result in minor injury.
ATTENTION!
Indicates a potentially hazardous situation
that can result in property damage.
PKSA 20-Li A1
GB
IE
NI
 3
Features
Front hand guard
Front handle
Chain oil tank cap
Safety lock-out
ON/OFF switch
Rear handle
Bumper spike (pre-assembled)
Guide rail (pre-assembled)
Saw chain (pre-assembled)
Grinder support
Fixing screw
Chain tensioning ring
Sprocket cover
Battery charge level button
Battery display LED
Battery pack*
Release button for the battery pack
Oil dispenser
Chain sprocket
Slotted hole in the guide rail
Blade guide
High-speed battery charger*
Red charge control LED
Green charge control LED
Cover for the guide rail (chain guard)
Organic chain oil
Package contents
1 cordless chain saw
1 Oregon 10" saw chain 91P040X
(pre-assembled)
1 Oregon 10" guide rail 100NDEA041
(pre-assembled)
1 cover for the guide rail (chain guard)
180 ml organic chain oil (Made in Germany)
1 set of operating instructions
Technical specifications
Cordless chain saw
Nominal voltage: 20 V
(DC)
Idle speed: 2,900rpm
Max. chain speed: 5.6 m/s
Oil tank capacity: approx. 275 ml
Guide rail: Oregon 10"
100NDEA041
Saw chain: Oregon 10" 91P040X
Chain pitch: 0,375" (9,525 mm)
Drive link thickness: 1.27 mm (0.050")
Number of teeth on the
chain sprocket: 6
Length of the guide rail: 305 mm
Usable cut length/guide
rail 230 mm
Battery: PAP 20 A3*
Type: LITHIUM ION
Rated voltage: 20 V
(DC)
Capacity: 4 Ah (80Wh)
Cells: 10
High-speed battery charger: PLG 20 A3*
INPUT:
Rated voltage: 230–240 V
~
, 50 Hz
(AC)
Rated power
consumption: 120 W
Fuse (internal): 3.15 A
T3.15A
OUTPUT:
Rated voltage: 21.5 V
(DC)
Rated current: 4.5 A
Charging time: approx. 60 min
Protection class: II / (double insulation)
*BATTERY AND CHARGER ARE NOT INCLUDED
PKSA 20-Li A1
4 
GB
IE
NI
Noise emission value:
Noise measurement value determined in accordance
with EN 60745-2-13. The A-rated noise level of
the power tool is typically:
Sound pressure level: L
pA
= 86.3 dB (A)
(at operator position)
Uncertainty K: K
pA
= 3 dB
Sound power level: L
WA
= 94.7 dB (A)
Uncertainty K: K
WA
= 2.6 dB
Guaranteed sound
power level: L
WA
= 97 dB (A)
(according to 2000/14/EC
amended by 2005/88/EC)
Wear ear muffs!
Total vibration value:
Total vibration values (vector total of three directions)
determined in accordance with EN 60745-2-13:
Vibration at the handle:
a
h
= 7.3 m/s
2
, K = 1.5 m/s
2
WARNING!
The vibration level varies depending on the
use of the power tool and may be higher
than the value specified in these instructions
in some cases. Regular use of the power tool
in this way may cause the user to underesti-
mate the vibration. Try to keep the vibration
loads as low as possible. Measures to reduce
the vibration load are, e.g. wearing gloves
and limiting the working time. Wherein all
states of operation must be included (e.g.
times when the power tool is switched off and
times where the power tool is switched on but
running without load).
NOTE
The vibration level specified in these instruc-
tions has been measured in accordance
with the standardised measuring procedure
specified in EN 60745 and can be used to
make equipment comparisons. The specified
vibration emission value can also be used to
make an initial exposure estimate.
WARNING!
You can reduce the vibration risk, for example,
the risk of Raynaud's phenomenon (circulatory
problems), by taking regular breaks during
which you rub your hands together.
The following symbols are used in these
operating instructions/on the tool:
Read these operating instructions
thoroughly before using the tool for
the first time, and retain them for
future reference.
Warning! Read the operating
instructions before use!
WARNING! Special safety precau-
tions are required when working
with the chainsaw.
Read and observe all warnings!
Wear snugly fitting protective
clothing with a cut-resistant lining.
Wear a hard hat!
Wear safety goggles!
Wear ear muffs!
Wear protective gloves!
Wear non-slip safety shoes!
PKSA 20-Li A1
GB
IE
NI
 5
WARNING! Risk of kickback.
Protect yourself from kickback from
the chainsaw and avoid all contact
with the rail tip.
WARNING! Risk of kickback!
Do not saw with the tip of the blade.
Always operate the chainsaw with
both hands.
Do not work with the chainsaw in
one hand.
Beware of flying objects!
Attention! Risk of injury from sharp
blades.
Protect the tool from rain and
moisture!
Before performing any maintenance
work, turn off the tool and discon-
nect the battery!
Guaranteed sound power level of
the tool
Block and unblock the chain brake
Running direction of the chain
Guide rail length
General power tool
safety warnings
WARNING!
Read all safety warnings and all
instructions. Failure to follow the
warnings and instructions may result
in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmos-
pheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
PKSA 20-Li A1
6 
GB
IE
NI
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat,
or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your
finger on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that can-
not be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are dan-
gerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have
the power tool repaired before use. Many
accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
PKSA 20-Li A1
GB
IE
NI
 7
5. Use and handling of the cordless
electrical power tool
a) Charge a rechargeable battery unit using
only the charger recommended by the manu-
facturer. Chargers are often designed for a
particular type of rechargeable battery unit.
There is the danger of fire if other types of re-
chargeable battery units are used.
b) Only the rechargeable battery units supplied
are to be used with an electrical power tool.
The use of other rechargeable battery units may
lead to the danger of injury or fire.
c) When they are not being used, store re-
chargeable battery units away from paper-
clips, coins, keys, nails, screws or other small
metal objects that could cause the contacts
to be bridged. Short-circuiting the contacts of
a rechargeable battery unit may result in heat
damage or fire.
d) Fluids may leak out of rechargeable battery
units if they are misused. If this happens,
avoid contact with the fluid. If contact occurs,
flush the affected area with water. Seek addi-
tional medical help if any of the fluid gets into
your eyes. Escaping battery fluid may cause
skin irritation or burns.
CAUTION! RISK OF EXPLOSION!
Never charge non-rechargeable
batteries.
Protect the rechargeable battery
from heat (for example, from continu-
ous exposure to sunlight), fire, water
and moisture. There is a risk of explo-
sion.
6. Service
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
b) Never try to repair damaged batteries. Batter-
ies should only be maintained by the manufac-
turer or an approved customer service centre.
Original accessories/auxiliary
equipment
Use only the accessories and additional equip-
ment specified in the operating instructions and
which are compatible with the tool.
WARNING!
Do not use any accessories that are not
recommended by PARKSIDE. This can lead to
an electric shock and fire.
PKSA 20-Li A1
8 
GB
IE
NI
Safety instructions for
chainsaws
IMPORTANT!
READ CAREFULLY BEFORE USE
AND STORE SAFELY FOR LATER
USE.
General power tool safety warnings
WARNING!
Stay alert, watch what you are doing and
use common sense when operating the
tool. Do not use the tool while you are
ill, tired or under the influence of drugs,
alcohol or medication.
A moment of inattention while operating the
tool may result in serious personal injury.
Avoid improper use. Use the machine only
as described under "Intended use".
Keep all body parts away from the saw chain
while the saw is running. Before starting the
saw, make sure that the saw chain is not touch-
ing anything. When working with a chainsaw, a
moment of inattentiveness can lead to clothing or
body parts getting caught in the saw chain.
Always hold the chainsaw with your right
hand on the rear handle and your left hand
on the front handle. Holding the chainsaw in
an inverted working posture increases the risk
of injuries and is prohibited.
Hold the power tool only by the insulated
gripping surfaces because the saw chain can
come into contact with hidden cables. Saw
chains touching a live wire make metal parts of
the power tool live and could cause an electric
shock to the operator.
Wear protective goggles and ear muffs.
Additional protective equipment for your
head, hands, legs and feet is recommended.
Suitable protective clothing reduces the risk of
injury from flying chips and accidental contact
with the saw chain.
Do not use the chainsaw in a tree. When
working in a tree, there is a risk of injury.
Make sure you have firm footing and use the
chainsaw only when standing on firm, safe
and level ground. Slippery ground or unstable
standing surfaces (e.g. on a step ladder) can
lead to a loss of balance or loss of control of
the chainsaw.
When sawing a branch that is under tension,
be prepared for it to spring back. Once the
tension in the wooden fibres is released, the
branch can hit the operator and/or knock the
chainsaw out of his hands.
Be extremely careful when cutting brushwood
and young trees. The thin material can catch in
the saw chain and fly in your direction or knock
you off balance.
Carry the chainsaw by the front handle when
switched off, with the saw chain facing away
from your body. When transporting or storing
the chainsaw, always put on the protective
cover. Careful handling of the chainsaw reduc-
es the probability of accidental contact with the
running saw chain.
Follow the instructions for lubrication, chain
tension and changing accessories. An incor-
rectly tensioned or lubricated chain can break
or increase the risk of kickback.
Keep the handles dry, clean and free from oil
and grease. Greasy, oily handles are slippery
and result in loss of control.
Saw wood only. Do not use the chainsaw for
work for which it is not intended. For example:
do not use the chainsaw to saw plastic,
masonry, or construction materials that are
not made of wood. Using the chainsaw for
work other than that for which it was intended
can lead to hazardous situations.
Start the cut using full power and keep the
chainsaw at top speed while sawing.
Ensure that there are no objects on the ground
that you can trip over.
Before using the tool for the first time, read the
operating instructions and pay close attention
to the safety instructions.
PKSA 20-Li A1
GB
IE
NI
 9
The warning and safety signs on the tool pro-
vide important information for safe operation.
In addition to the notices in these operating
instructions, all general safety and accident pre-
vention legislation must also be complied with.
Keep plastic wrapping away from children.
There is a risk of suffocation!
Insufficiently informed operators can be a
danger to other people and themselves due to
improper use. The operator is responsible for
third parties.
Be very careful when handling the tool. Use
common sense when working and play close
attention to what you are doing.
Do not work for longer than 10 minutes in one
session. We recommend taking a break of
10–20 minutes between working sessions.
Lend the tool only to users who have experi-
ence with the tool. Hand over the operating
instructions at the same time.
Some cutting tasks require special training and
particular skills. If in doubt, please consult an
expert.
First-time users must seek training to familiarise
themselves with the characteristics of the tool.
For your safety, attend a state-approved chain-
saw training course.
When not in use, the tool must be secured to
ensure that it is not a risk to anyone else.
Secure against unauthorised access.
The user of the tool is responsible for all acci-
dents and risks that cause injury or damage to
other people's property.
Children, adolescents and people with reduced
physical, sensory or mental capabilities must
not use the chainsaw. The only exception to this
are young people over the age of 16 who are
being trained by a specialist.
Note that improper maintenance, the use of
non-approved spare parts, or the removal or
modification of the safety equipment can lead
to damage to the tool and severe injuries to the
operator.
Precautions against kickback
WARNING! KICKBACK!
Be aware of the danger of kickback when
working with the tool. There is a risk of personal
injury. You can avoid kickbacks by being care-
ful and using the correct sawing technique.
Contact with the tip of the rail can, in some
cases, lead to an unexpected rearwards reac-
tion resulting in the guide rail flying upwards
towards the operator (see fig. A).
Fig. A
Kickbacks can occur if the tip of the guide rail
touches an object or if the wood bends and the
saw chain gets caught in the cut.
If the saw chain jams in the upper edge of the
guide rail, the chainsaw can kick back violently
towards the operator (see fold-out page, fig. F).
If the saw chain jams in the lower edge of the
guide rail, the chainsaw can jerk violently away
from the operator (see fold-out page, fig. G).
Be extremely careful when reapplying the chain
of the chainsaw to a cut you have already
started.
Do not saw any branches or pieces of wood
that can move their position during sawing or in
which the cut could close during sawing.
Any such reaction can lead to you losing control
over the saw and possibly injuring yourself. Do
not rely solely on the chainsaw's built-in safety
devices. As the user of a chainsaw, you can
take a number of measures to avoid accidents
and injury. A kickback is caused by incorrect
use or misuse. It can be avoided by taking
suitable precautions (as given below):
Bild 1
PKSA 20-Li A1
10 
GB
IE
NI
Hold the saw firmly with both hands, with
your thumb and fingers around the handles of
the chainsaw. Position your body and arms so
you can withstand kickback forces. If suitable
measures are taken, the operator can control
the kickback forces. Never let go of the chain-
saw (see fold-out page, fig. C).
Avoid an abnormal posture and do not saw
over shoulder height. This will prevent inadvert-
ent contact with the tip of the rail and allows a
better control of the chainsaw in unexpected
situations.
Always use the replacement rails and saw
chains specified by the manufacturer. Incorrect
replacement rails and saw chains can lead to a
breakage of the saw chain and/or kickback.
Follow the manufacturer's instructions for
sharpening and maintaining the saw chain.
Setting the depth stop too low can increase the
risk of kickback.
Do not saw with the tip of the blade. This can
lead to a kickback.
Make sure that are no nails or pieces of metal
in the cutting area. Pay particular attention
to nails or pieces of iron in the area of the cut.
Also be careful when cutting hardwoods in
which the chain could jam. This can lead to a
kickback.
Personal protective equipment (PPE)
DANGER!
Wear personal protective equipment (PPE)!
Wear a hard hat with a visor or safety
goggles and ear muffs.
Wear snugly fitting protective clothing
with a cut-resistant lining.
Wear non-slip safety shoes!
Wear protective gloves!
Avoid loose-fitting clothing that can get caught.
Do not wear a scarf, tie or any jewellery!
If you have long hair, wear a hairnet!
Always wear a helmet when working in wooded
areas. This offers protection from falling branches.
Check the helmet regularly for damage.
Replace it after 5 years at most.
Use only approved protective helmets.
The face shield/safety goggles protect the user
from wood chips and splinters.
To prevent eye injuries, always use a face shield
or safety goggles while working with the tool.
Always wear ear muffs.
The noise produced by the tool can damage
your hearing.
Wear robust protective gloves made of a durable
material, e.g. leather.
Wear a dust mask when sawing dry wood.
Sawing can generate sawdust.
Storage and transportation
Switch off the chainsaw before moving it any-
where, even short distances.
Engage the chain brake and put on the chain
guard.
Always use the chain guard for transportation
and storage (see fold-out page, fig. I).
Protect the machine during transport (also in
vehicles) against tipping over to prevent dam-
age or injuries.
Carry the tool by the front handle only. Make
sure the guide rail is facing to the rear, away
from your body (see fold-out page, fig. I).
Clean and maintain the chainsaw before storage.
Store the tool in a secure and dry location.
Secure it against unauthorised access.
PKSA 20-Li A1
GB
IE
NI
 11
Environmental safety
Work only in daylight.
Do not work in inopportune weather conditions,
such as rain or wind.
This will lead to an increased risk of accidents.
Keep your work area clean and tidy.
Keep children, other people and animals at a
distance before and during the work.
Distractions can cause you to lose control.
Before starting work, ensure that no people,
animals or valuable property are inside the
danger zone.
Do not work in the vicinity of wire fences or
areas with loose old wire.
Vibrations
WARNING!
You can reduce the vibration risk, for exam-
ple, the risk of Raynaud's phenomenon (cir-
culatory problems), by taking regular breaks
during which you rub your hands together.
Always wear protective gloves and ensure your
hands are warm.
Make sure that the chain is always sharp.
Take regular work breaks.
Safety guidelines for battery chargers
This tool may be used by children
aged 8 years and above and by
persons with limited physical, senso-
ry or mental capabilities or lack of
experience and knowledge, provid-
ed that they are under supervision
or have been told how to use the
tool safely and are aware of the po-
tential risks. Do not allow children
to use the tool as a toy. Cleaning
and user maintenance tasks may
not be carried out by children un-
less they are supervised.
To avoid potential risks, damaged
mains cables should be replaced
by the manufacturer, their customer
service department or a similarly
qualified person.
The charger is suitable for indoor use
only.
WARNING!
To avoid potential risks, damaged mains
cables should be replaced by the manufac-
turer, their customer service department or a
similarly qualified person.
ATTENTION!
This charger can only charge the following bat-
teries: PAP 20 A1 / PAP 20 A2 / PAP 20 A3.
A current list of battery compatibility can be
found at www.Lidl.de/Akku.
PKSA 20-Li A1
12 
GB
IE
NI
Before use
RISK OF INJURY!
Always switch the tool off and remove the bat-
tery before carrying out any work on the tool.
WARNING!
Always carry out checks before use and with
the tool switched off.
Check that the tool is in good working order
before every use and after it has been
dropped.
Check whether moving parts work properly.
Many accidents are caused by poorly main-
tained tools.
Have any damage repaired by qualified
specialists.
Use the chainsaw and accessories only as
described in these instructions, taking into
account the working conditions and the work
to be performed.
Using machine tools for purposes different
from those intended could result in a hazard-
ous situation.
Check the chain brake is in good working order
regularly (front hand guard, see fold-out page,
fig. B).
Check that the guide rail is correctly fitted.
Check that the saw chain is correctly tensioned.
Follow the instructions for lubrication, chain
tension and changing accessories. An incorrectly
tensioned or lubricated chain can break or
increase the risk of kickback.
Keep cutting tools sharp and clean. Sharpen
them regularly and replace worn parts prompt-
ly. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
Check the throttle control and the throttle control
lock for freedom of movement. The throttle con-
trol must spring back into the start position.
Check whether the handles are clean, dry and
free of oil and dirt.
Never carry out the work alone. In case of
emergency, someone should be close by.
Use the chainsaw only if you are standing on
firm, safe and even ground.
Do not overreach.
Slippery ground or unstable standing surfaces
(e.g. on a step ladder) can lead to a loss of
balance or loss of control of the chainsaw.
Keep proper footing and balance at all times.
This enables better control of the chainsaw in
unexpected situations.
Do not use the chainsaw in a tree. When working
in a tree there is a risk of injury.
Never saw above shoulder height.
Always hold the chainsaw with your right hand
on the rear handle and your left hand on the
front handle (see fold-out, page fig. C). Holding
the chainsaw in an inverted working posture
increases the risk of injuries and is prohibited.
When the chainsaw is running, keep all body
parts away from the saw chain. Before starting
the chainsaw, make sure that the saw chain is
not touching anything. When working with a
chainsaw, a moment of inattentiveness can lead
to clothing or body parts getting caught in the
saw chain.
Switch the chainsaw off immediately if you no-
tice any changes in the way the tool behaves.
If the chainsaw hits a stone, nails or other hard
objects, stop the motor immediately and check
the saw chain and the guide rail for damage.
PKSA 20-Li A1
GB
IE
NI
 13
Do not drop the chainsaw, knock it against ob-
structions and do not use the guide rail as a lever.
Use the chainsaw only for sawing wood.
When sawing a branch that is under tension, be
prepared for it to spring back. Once the tension
in the wooden fibres is released, the branch can
hit the operator and/or knock the chainsaw out
of his hands.
Be extremely careful when cutting brushwood
and young trees. The thin material can catch in
the saw chain and fly in your direction or knock
you off balance.
Charging the battery pack (see fig. A)
CAUTION!
Always unplug the tool before you remove
the battery pack from or connect the battery
pack to the charger.
NOTE
Never charge the battery pack at an ambient
temperature of below 10°C or above 40°C.
If a lithium-ion battery is to be stored for an
extended period, the charge level should be
checked regularly. The optimum charge level
is between 50% and 80%. The storage
climate should be cool and dry and the
ambient temperature should be between 0°C
and 50°C.
Connect the battery pack
to the high-speed
battery charger
(see fig. A).
Insert the power plug into the socket.
The charge control LED
lights up red.
The green charge control LED
indicates that
the charging process is complete and the bat-
tery pack is ready for use.
ATTENTION!
If the red charge control LED
flashes, this
means that the battery pack has overheat-
ed and cannot be charged.
If the red and green charge control LEDs
both flash, this means that the battery
pack is defective.
Switch off the charger for at least 15 minutes
between successive charging sessions. Also
disconnect the power plug from the mains
power socket.
Attaching/disconnecting the battery
pack to/from the tool
Attaching the battery pack:
Push the battery pack
into the handle until
it clicks into place.
Removing the battery pack:
Press the release button
and remove the
battery pack.
Checking the battery charge level
Press the battery charge level button to
check the status of the battery (see also main
diagram).
The status/remaining charge will be shown on
the battery display LED
as follows:
RED/ORANGE/GREEN = maximum charge
RED / ORANGE = medium charge
RED = low charge – charge the battery
Adding chain oil
WARNING!
Always check the chain lubrication before
starting work.
Never work without chain lubrication!
If the saw chain runs dry, the cutting equip-
ment may become irreparably damaged in a
short time.
NOTE
Use only saw chain oil, preferably biode-
gradable. Do not use waste oil, motor oil, etc.
While working, check whether the chain
lubrication is working correctly.
PKSA 20-Li A1
14 
GB
IE
NI
Always clean the area around the chain oil tank
cap
before filling to prevent dirt getting into
the chain oil tank.
Use a dry, lint-free cloth to do this.
Turn the chain oil tank cap
anticlockwise
and remove it.
The chain oil tank cap
is connected to the
chain oil tank with an loss-prevention device
and cannot fall onto the floor.
Add the supplied organic chain oil
to the
chain oil tank.
Do not spill any chain oil while filling the chain
oil tank and do not fill the tank to overflowing.
Wipe up any spilt chain oil immediately.
Turn the chain oil tank cap
clockwise to
close it.
Tightening and checking the saw chain
WARNING!
Wear protective gloves! There is a risk of
injury from the sharp cutting teeth!
Check the chain tension before every use.
Undo the fixing screw
.
Turn the chain tensioning ring
in a clockwise
direction to increase the tension.
The saw chain
must lie against the underside
of the blade.
Check whether the saw chain (with the chain
brake off, pull the front hand guard to the rear)
can be drawn by hand over the guide rail .
Now tighten the fixing screw completely.
NOTE
A new saw chain
stretches and must be
tightened more often.
Use
Before starting the tool, always check that:
The protective equipment and cutting equipment
is complete and in perfect working order.
All screw connections are firmly tightened.
All moving parts can move smoothly and freely.
Switching on and off
Switching on:
Press the safety lock-out and keep it pressed
and then press the ON/OFF switch
.
After starting, the safety lock-out
can be
released again.
Switching off:
Release the ON/OFF switch
.
Optimal working procedures
Get to know the chainsaw before you start to use it.
Checking and adjusting the chain
lubrication
ATTENTION!
Never work without chain lubrication!
If the saw chain runs dry, the cutting equip-
ment may become irreparably damaged in a
short time.
Always check the chain lubrication before
starting work.
NOTE
Use only saw chain oil, preferably biode-
gradable. Do not use waste oil, motor oil, etc.
While working, check whether the chain
lubrication is working correctly.
With the chainsaw running, hold it over a sawn
off tree stump or a suitable ground sheet.
If the lubrication is adequate, a light film of oil
forms on the tree stump or the ground sheet
(see fold-out page, fig. D).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111

Parkside 327520 Translation Of The Original Instructions

Catégorie
Tronçonneuses électriques
Taper
Translation Of The Original Instructions
Ce manuel convient également à

dans d''autres langues