Maytag MVWC565FW MVWC565FW Use and Care EN

Marque: Maytag

Modèle: MVWC565FW

Catégorie: Machines à laver

Taper: MVWC565FW Use and Care EN

W10871756A

W10878108A-SP

Designed to use only

HE High Efﬁciency detergents.

Conçue pour l’utilisation d’un

détergent haute efﬁcacité seulement.

TOP-LOADING

HIGH EFFICIENCY

WASHER

USE AND CARE GUIDE

Table of Contents

WASHER SAFETY ...................................................................2

WHAT’S NEW UNDER THE LID? .........................................3

CONTROL PANEL AND FEATURES ....................................4

CYCLE GUIDE ...........................................................................6

USING YOUR WASHER ......................................................... 7

WASHER MAINTENANCE ...................................................10

TROUBLESHOOTING ...........................................................12

WARRANTY ............................................................................17

ASSISTANCE OR SERVICE ..........................BACK COVER

Table des matières

SÉCURITÉ DE LA LAVEUSE ...............................................18

QUOI DE NEUF SOUS LE COUVERCLE? .......................19

TABLEAU DE COMMANDE ET

CARACTÉRISTIQUES ...........................................................20

GUIDE DE PROGRAMMES .................................................22

UTILISATION DE LA LAVEUSE ..........................................23

ENTRETIEN DE LA LAVEUSE .............................................26

DÉPANNAGE ..........................................................................28

GARANTIE ...............................................................................34

ASSISTANCE OU SERVICE ......COUVERTURE ARRIÈRE

GUIDE D’UTILISATION

ET D’ENTRETIEN DE

LA LAVEUSE À FAIBLE

CONSOMMATION D’EAU

AVEC CHARGEMENT PAR

LE DESSUS

Para una versión de estas instrucciones en español, visite www.maytag.com

WASHER SAFETY

WHAT’S NEW UNDER THE LID?

Your new washer will operate differently than your past agitator-style washer.

Choosing the Right Detergent

Use only High Efﬁciency detergents. The package will be marked

“HE” or “High Efﬁciency.” Using non-HE detergent will likely result

in longer cycle times and reduced rinsing performance. It may also

result in component malfunction and, over time, buildup of mold or

mildew. HE detergents should be low-sudsing and quick-dispersing

to produce the right amount of suds for the best performance. They

should hold soil in suspension so it is not redeposited onto clean

clothes. Not all detergents labeled as High Efﬁciency are identical

in formulation and their ability to reduce suds. For example, natural,

organic, or homemade HE detergents may generate a high level of

suds. Always follow the detergent manufacturer’s instructions to

determine the amount of detergent to use.

Normal Sounds You Can Expect

At different stages of the wash cycle, you may hear sounds

and noises that are different from those of your previous washer.

For example, you may hear a clicking and hum at the beginning of

the spin phase, as the lid lock goes through a self-test. There will

be different kinds of humming sounds as the agitator tests for load

balance or moves the load. And sometimes, you may hear nothing

at all, as the washer determines the correct water level for your load

or allows time for clothes to soak.

Use only High Efﬁciency (HE) detergent.

Lid Lock

To allow for higher spin speeds, the lid will lock and the Lid

Locked light will turn on. When this light is lit, the lid is locked

and cannot be opened. When this light is blinking, the washer

is paused. When this light is off, the lid can be opened. After a

cycle is started, the washer will ﬁll to the appropriate water level.

When the washer is done ﬁlling, it will start to agitate. If you need

to open the lid to add a garment after this point, the lid will remain

unlocked during the entire agitation portion of the wash phase.

The cycle will automatically pause when the lid is opened, and the

cycle will resume once the lid is closed. The lid will lock before

the spin phase begins. If you need to pause or stop after this

point, you must press the START/PAUSE button and wait for the

lid to unlock. The lid will only unlock after washer movement has

stopped. Depending on when in the cycle you try to pause, it may

take several seconds to several minutes for the lid to unlock. Press

START/PAUSE to resume the cycle.

Water Level Options

Set the Water Level knob to the Auto Sensing setting and the

washer automatically adjusts the water level to the load size. Set

the Water Level knob to the Deep Water Wash setting and the

washer will ﬁll to the maximum water level.

Sensing

This washer will perform a series of spins to check for load balance.

During this time, a series of clicks and a whirring noise signal that

sensing technology is determining if there is an off-balance load.

Spray Rinse

Select cycles default to a spray rinse. During these cycles, you will

hear water enter the washer as the tub spins, allowing the rinse

water to penetrate clothes. Check the “Cycle Guide” for details.

IMPORTANT:

■ The lid must be closed before the washer basket ﬁlls with water and for the wash cycle to start. If the lid is open and ﬁlling stops, close the

lid and press START/PAUSE to complete the cycle.

■ Rinse options must be set to either One Rinse with Fabric Softener or Two Rinses with Fabric Softener when using fabric softener in the

fabric softener dispenser. This ensures that fabric softener is added at the correct time in the rinse phase and is evenly distributed.

CONTROL PANEL AND FEATURES

WATER LEVEL

Set the Water Level knob to the Auto Sensing setting and the

washer will automatically sense the appropriate water level for

the load size and type.

Set the Water Level knob to the Deep Water Wash setting and

the washer will ﬁll to the maximum water level.

NOTE: Expect longer cycles times due to extended ﬁll times

when using the Deep Water Wash option.

START/PAUSE BUTTON

Press to start the selected cycle. Press again to pause the

cycle and unlock the lid. Press and hold 3 sec. to cancel a cycle.

NOTE: If the washer is spinning, it may take several minutes

to unlock the lid.

Press and hold 3 sec to cancel a cycle and drain the water from

the washer.

PROGRESS LIGHTS

The Progress Lights show the progress of a cycle. At each

stage of the process, you may notice sounds or pauses that are

different from your previous washer.

SENSING

When the Start/Pause button is pressed, and the Water

Level knob is set to Auto Sensing, the washer will ﬁll and

begin sensing to determine load size and balance.

Once sensing is complete, the washer will ﬁll to the

appropriate level for the detected load size and then

begin the wash phase of the cycle.

NOTE: Sensing and wash phases will be paused by opening

the unlocked lid. Close the lid to resume the cycle. If the lid

is left open for more than 10 minutes, the washer will cancel

the cycle and pump out the water. The lid will lock after the

wash phase to begin the initial spinout and remain locked for

the remainder of the cycle.

SOIL LEVEL

Select the setting most suitable for your load. For heavily soiled

and sturdy fabrics, select Heavy Soil Level for more wash time.

For lightly soiled and delicate fabrics, select Light Soil Level

for less wash time. A lighter soil-level setting will help reduce

tangling and wrinkling.

WASH TEMP

Wash Temp senses and maintains uniform water temperatures

by regulating incoming hot and cold water.

Select a wash temperature based on the type of fabric and soils

being washed. For best results and following the garment-label

instructions, use the warmest wash water safe for your fabric.

• On some models and cycles, warm and hot water may be

cooler than your previous washer.

• Even in a cold- and cool-water wash, some warm water may

be added to the washer to maintain a minimum temperature.

All rinses are cold.

WASH CYCLE KNOB

Use the Wash Cycle knob to select cycles on your washer. See

“Cycle Guide” for detailed descriptions of cycles.

RINSE OPTIONS

The following options may be added to most cycles. See “Cycle

Guide” for additional details.

1 RINSE

This option is used to limit a cycle to one rinse.

2 RINSES

This option can be used to automatically add a second rinse

to most cycles.

1 RINSE WITH FABRIC SOFTENER

This option must be selected if using fabric softener during a

cycle. It ensures that fabric softener is added at the correct

time in the rinse for even distribution.

TWO RINSES WITH FABRIC SOFTENER

This option turns on both the Fabric Softener and the

2 Rinses option.

Not all features and options are available on all models.

Appearance may vary.

4 5

WASH

The washer will ﬁll to the correct water level based on the

load size and the Water Level selection. Certain cycles may

agitate during the ﬁll process to boost cleaning. You will

hear the agitator rotate followed by a pause lasting several

seconds. When the wash cycle begins, you will hear the

agitator increase speed. The motor sounds may change at

different stages in the wash cycle while the washer performs

different wash actions.

RINSE

Certain cycles use a spray rinse, which adds water to the tub

while the basket spins. You will hear sounds similar to the

wash cycle as the washer rinses and moves the load. You

may hear the motor turning on brieﬂy (short hum) to move the

basket while ﬁlling.

SPIN

The washer spins the load at increasing speeds for proper

water removal based on the selected cycle and spin speed.

DONE

Once the cycle is complete, this light will come on. For best

results, promptly remove the load.

LID LOCKED

The Lock feature allows for higher spin

speeds. When lit, the lid is locked and

cannot be opened without pausing the

cycle. When the light is off, the lid can

be opened.

To open the lid after it has been locked, press START/

PAUSE. The lid will unlock once the washer movement

has stopped. This may take several minutes if the load

was spinning at high speed. Press START/PAUSE while

the lid is closed to resume the cycle.

Sturdy fabrics,

colorfast items,

towels, jeans

Power Wash

Hot

Warm

Cool

Cold

Tap Cold

High Use this cycle for heavily soiled or sturdy items. Water-level

sensing process may take longer for some items than for others

because they will absorb more water than other fabric types.

Heavily soiled

white fabrics

Whites

Hot

Warm

Cool

Cold

Tap Cold

High This cycle, when used with chlorine bleach, improves whitening

of soiled white fabrics.

Large items such

as sheets, sleeping

bags, small

comforters, jackets,

small, washable rugs

Bulky/Sheets Hot

Warm

Cool

Cold

Tap Cold

Low Use this cycle to wash large items such as jackets and small

comforters. The washer will ﬁll with enough water to wet down

the load before the wash portion of the cycle begins and uses a

higher water level than other cycles.

Cottons, linens, and

mixed-garment loads

Normal Hot

Warm

Cool

Cold

Tap Cold

High Use this cycle for normally soiled cottons and mixed-fabric

loads.

No-iron fabrics,

cottons, perm press,

linens, synthetics

Wrinkle Control Hot

Warm

Cool

Cold

Tap Cold

Low Use this cycle to wash loads of no-iron fabrics such as sport

shirts, blouses, casual business clothes, permanent press, and

blends.

Machine-wash silks,

handwash fabrics

Hand Wash Hot

Warm

Cool

Cold

Tap Cold

Low Use this cycle to wash lightly soiled items indicating “Machine

Washable Silks” or “Gentle” cycle on the care label. Place small

items in mesh garment bags before washing. This cycle uses a

higher, preset water level.

Bright or darkly

colored cottons,

linens, casual and

mixed loads

Cold Wash

Cold

High Cold water with an additional wash action gently lifts stains

while caring for fabrics. Settings may be adjusted as desired

but must use only cold water settings.

Heavily soiled fabrics Soak Hot

Warm

Cool

Cold

Tap Cold

No Spin Use this cycle to soak small spots of set in stains on fabrics.

The washer will use intermittent agitation and soaking. After

time has expired, water will drain, but the washer will not spin.

Cycle is complete.

Swimsuits and items

requiring rinsing

without detergent

Rinse &

Spin

Cold rinse only High Combines a rinse and high-speed spin for loads requiring an

additional rinse cycle. Use this cycle to complete a load after

power interruption or for loads that require rinsing only.

Hand-washed items

or dripping-wet items

Drain &

Spin

N/A High This cycle uses a spin to shorten drying times for heavy fabrics

or special-care items washed by hand. Use this cycle to drain

washer after canceling a cycle or completing a cycle after a

power failure.

No clothes in washer Clean Washer

with affresh

Hot

Low Use this cycle every 30 washes to keep the inside of your

washer fresh and clean. This cycle uses a higher water level.

Use with affresh® Washer Cleaner tablet or liquid chlorine

bleach to thoroughly clean the inside of your washer. This cycle

should not be interrupted. See “Washer Care.”

IMPORTANT: Do not place garments or other items in the

washer during the Clean Washer with affresh® cycle. Use this

cycle with an empty wash tub.

CYCLE GUIDE

For best fabric care, choose the cycle that best ﬁts the load being washed.

Recommended settings for best performance are shown in Bold.

Not all cycles and options are available on all models. Not all settings and options are available on each cycle.

NOTE: If you are using fabric softener, be sure to select either 1 Rinse with Fabric Softener or 2 Rinses with Fabric Softener.

*All rinses are cold.

Items to wash: Cycle: Wash Temp*: Spin

Speed:

Cycle Details:

USING YOUR WASHER

• Empty pockets. Loose change, buttons, or any small object

can pass under the agitator and become trapped, causing

unexpected sounds.

• Sort items by recommended cycle, water temperature, and

colorfastness.

• Separate heavily soiled items from lightly soiled.

• Separate delicate items from sturdy fabrics.

• Do not dry items if stains remain after washing, because heat

can set stains into fabric.

• Treat stains promptly.

• Close zippers, fasten hooks, tie strings and sashes, and

remove non-washable trim and ornaments.

• Mend rips and tears to avoid further damage to items during

washing.

Helpful Tips:

• When washing water-proof or water-resistant items, load

evenly.

• Use mesh garment bags to help avoid tangling when washing

delicate or small items.

• Turn knits inside out to avoid pilling. Separate lint-takers from

lint-givers. Synthetics, knits, and corduroy fabrics will pick up

lint from towels, rugs, and chenille fabrics.

NOTE: Always read and follow fabric care label instructions to

avoid damage to your items.

1. Sort and prepare your laundry

Add a measured amount of HE detergent

or single-dose laundry packet into the

basket.

If using Oxi-type boosters, color-safe

bleach, or fabric-softener crystals, add to

the bottom of the washer basket before adding clothes.

IMPORTANT: Use only High Efﬁciency detergents. The

package will be marked “HE” or “High Efﬁciency.” Using regular

detergent will likely result in longer cycle times and reduced

rinsing performance. It may also result in component failures and

noticeable mold or mildew. HE detergents are made to produce

the right amount of suds for the best performance.

NOTE: Follow the manufacturer’s instructions to determine the

amount of laundry products to use.

2. Add laundry products

5. Add fabric softener

Pour a measured amount of liquid fabric

softener into dispenser; always follow

manufacturer’s directions for correct amount

of fabric softener based on your load size.

Dilute liquid fabric softener by ﬁlling the

dispenser with warm water until liquid reaches the underside

of the rim. See max ﬁll line arrows.

IMPORTANT: The Rinse Options knob must be set to either

1 Rinse with Fabric Softener or 2 Rinses with Fabric Softener

when using fabric softener in the fabric softener dispenser. This

ensures that fabric softener is added at the correct time in the

rinse phase and is evenly distributed.

Adding Liquid Fabric Softener Manually to Wash Load

During the ﬁnal rinse, wait until the washer has completed ﬁlling

and press the START/Pause button to pause the washer. Lift the

lid and add the measured, recommended amount of liquid fabric

softener. Do not use more than the recommended amount. Close

the lid and press the START/Pause button again to start the

washer.

4. Add liquid chlorine bleach

to dispenser

Liquid

Chlorine Bleach

Do not overﬁll, dilute, or use more than 1 cup (250mL). Do not

use color-safe bleach or Oxi products in the same cycle with

liquid chlorine bleach.

Turn cycle knob to choose your wash cycle. For more

information, see “Cycle Guide.”

6. Select cycle

3. Load laundry into washer

Load garments in loose heaps evenly

around basket wall. For best results, do

not pack the load tightly. Do not wrap large

items such as sheets around the agitator;

load them in loose piles around the sides of

the basket. Try mixing different-sized items

to reduce tangling.

IMPORTANT: Do not tightly pack or force items into washer.

Items need to move freely for best cleaning and to reduce

wrinkling and tangling.

MAX FILL

Wash Temp Suggested Fabrics

8. Select wash temperature

Once you select a cycle, select the wash temperature

by turning the Wash Temp knob to the desired setting.

Always read and follow fabric care label instructions to avoid

damage to your items.

9. Select RINSE OPTIONS and

WATER LEVEL

Select the number of rinses by turning the Rinse Options knob to

the desired setting.

IMPORTANT: The Rinse Options knob must be set to an option

“with Fabric Softener” when using the fabric softener dispenser.

This ensures that fabric softener is added at the correct time in

the rinse for even distribution.

Set the Water Level knob to the Auto Sensing setting and the

washer will automatically sense the appropriate water level for

the load size and type.

Set the Water Level knob to the Deep Water Wash setting and

the washer will ﬁll to the maximum water level.

Note: The cycle will be longer due to extended ﬁll times when

using the Deep Water Wash setting.

10. Press START/Pause to

begin wash cycle

Press the START/PAUSE button to start the wash cycle. When

the cycle has ﬁnished, the Done status light will light. Promptly

remove garments after cycle has completed to avoid odor,

reduce wrinkling, and avoid rusting of metal hooks, zippers,

and snaps.

Unlocking the lid to add garments

If you need to add 1 or 2 missed garments after the wash has

started, simply open the lid and this will pause the cycle. After

adding the garments, simply close the lid and the cycle will

resume.

If, instead, you press the START/PAUSE button to pause the

cycle and then open the lid to add garments, you will need to

press the START/PAUSE button after closing the lid to resume

the cycle.

NOTE: Washer will not ﬁll with the lid open.

IMPORTANT: If lid is left open for more than 10 minutes, the

water will pump out automatically.

Manual soak

If you would like to manually soak your garments at any time

during the wash portion of the cycle, press START/PAUSE and

leave the lid closed. Once your desired soak time has elapsed,

press START/PAUSE again to continue the cycle. As long as the

lid remains closed, your soak time can be longer than 10 minutes.

However, if the lid is opened during the soak and remains open

for more than 10 minutes, the water will pump out automatically.

Cool

Warm water is added to assist in

soil removal and to help dissolve

detergents.

Cool is slightly warmer than Cold.

Dark colors that

bleed or fade

Light soils

Hot

Some cold water is added to save

energy. This will be cooler than your

hot water heater setting.

Warm

Some cold water will be added, so

this will be cooler than what your

previous washer provided.

Cold

Warm water may be added to assist

in soil removal and to help dissolve

detergents.

Whites and pastels

Durable items

Heavy soils

Bright colors

Moderate to light soils

Colors that bleed

or fade

Light soils

Dark colors that

bleed or fade

Light soils

Tap Cold

This is the temperature from your

faucet.

7. Select SOIL LEVEL

Once you select a cycle, select the soil level by turning the Soil

Level knob to the desired setting.

WASHER MAINTENANCE

Replace inlet hoses after 5 years of use to reduce the risk of

hose failure. Periodically inspect and replace inlet hoses if

bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of replacement

on the label with a permanent marker.

NOTE: This washer does not include inlet hoses. See the

“Installation Instructions” for more information.

WATER INLET HOSES

WASHER CARE

Recommendations to Help Keep Your Washer

Clean and Performing at its Best

1. Always use High Efﬁciency (HE) detergents and follow the

detergent manufacturer’s instructions regarding the amount

of detergent to use. Never use more than the recommended

amount because that may increase the rate at which

detergent and soil residue accumulate inside your washer,

which in turn may result in undesirable odor.

2. Use warm- and hot wash-water settings sometimes (not

exclusively cold-water washes) because they do a better

job of controlling the rate at which soils and detergent

accumulate.

3. Always leave the washer lid open between uses to help dry

out the washer and prevent the buildup of odor-causing

residue.

Cleaning Your Top Loading Washer

Read these instructions completely before beginning the

routine cleaning processes recommended below. This washer

maintenance procedure should be performed, at a minimum,

once per month or every 30 wash cycles, whichever occurs

sooner, to control the rate at which soils and detergent may

otherwise accumulate in your washer.

Cleaning the Inside of the Washer

To keep your washer odor-free, follow the usage instructions

provided above and use this recommended monthly cleaning

procedure:

Clean Washer Cycle

This washer has a special cycle that uses higher water volumes

in combination with affresh

Washer Cleaner or liquid chlorine

bleach to clean the inside of the washer.

Begin procedure

1. affresh

Washer Cleaner Cycle Procedure

(Recommended for Best Performance):

a. Open the washer lid and remove any clothing or items.

b. Place an affresh

Washer Cleaner tablet in the bottom of

the washer basket.

c. Do not place an affresh

Washer Cleaner tablet in the

detergent dispenser.

d. Do not add any detergent or other chemical to the washer

when following this procedure.

e. Close the washer lid.

f. Select the cycle recommended for cleaning the inside of

the washer.

g. Press the START/Pause button to start the cycle.

NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, press START/Pause once. After the cycle

has stopped, run a Rinse & Spin cycle to rinse cleaner from

washer.

WASHER CARE (cont.)

2. Chlorine Bleach Procedure (Alternative):

a. Open the washer lid and remove any clothing or items.

b. Add 1 cup (236 mL) of liquid chlorine bleach to the

bleach compartment.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause washer damage

over time.

c. Close the washer lid.

d. Do not add any detergent or other chemical

to the washer when following this procedure.

e. Select the cycle recommended for cleaning the inside of

the washer.

f. Press the START/Pause button to start the cycle.

NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, press START/Pause once. After the cycle

has stopped, run a Rinse & Spin cycle to rinse cleaner from

washer.

Description of Clean Washer Cycle Operation:

1. This cycle will ﬁll to a water level higher than in normal wash

cycles to provide rinsing at a level above the water line for

normal wash cycle.

2. During this cycle, there will be some agitation and spinning

to increase the removal of soils.

After this cycle is complete, leave the lid open to allow for better

ventilation and drying of the washer interior.

Cleaning the Dispensers

After a period of using your washer, you may ﬁnd some residue

buildup in the washer’s dispensers. To remove residue from

the dispensers, wipe them with a damp cloth and towel dry.

Do not attempt to remove the dispensers or trim for cleaning.

The dispensers and trim are not removable. If your model has

a dispenser drawer, however, remove the drawer and clean it

before or after you run the Clean Washer cycle. Use an

all-purpose surface cleaner if needed.

Cleaning the Outside of the Washer

Use a soft, damp cloth or sponge to wipe away any spills. Use

only mild soaps or cleaners when cleaning external washer

surfaces.

IMPORTANT: To avoid damaging the washer’s ﬁnish, do not

use abrasive products.

Operate your washer only when you are home. If moving, or

not using your washer for a period of time, follow these steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer, to avoid ﬂooding due

to water-pressure surge.

WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer

where it will not freeze. Some water may stay in hoses, and

freezing can damage washer. If storing or moving during

freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain

water-inlet hoses.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run

washer on Rinse & Spin cycle for about 30 seconds to mix

antifreeze and remaining water.

3. Unplug washer or disconnect power.

NON-USE AND VACATION CARE

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain

water-inlet hoses.

2. If washer will be moved during freezing weather, follow

“Winter Storage Care” directions before moving.

3. Disconnect drain hose from drain system and drain any

remaining water into a pan or bucket. Disconnect drain

hose from back of washer.

4. Unplug power cord.

5. Place inlet hoses and drain hose inside washer basket.

6. Drape power cord over edge and into washer basket.

7. Place packing tray from original shipping materials back

inside washer. If you do not have packing tray, place heavy

blankets or towels into basket opening. Close lid and place

tape over lid and down front of washer. Keep lid taped

until washer is placed in new location. Transport washer in

upright position.

REINSTALLING/USING WASHER AGAIN

To reinstall washer after non-use, vacation, winter storage,

or moving:

1. Refer to Installation Instructions to locate, level, and

connect washer.

2. Before using again, run washer through the following

recommended procedure:

To use washer again:

1. Flush water pipes and hoses. Reconnect water-inlet hoses.

Turn on both water faucets.

2. Plug in washer or reconnect power.

3. Run washer through Bulky/Sheets cycle to clean washer

and remove any antifreeze. Use half the manufacturer’s

recommended amount of detergent for a medium-size load.

TROUBLESHOOTING

If you experience Possible Causes Solution

Vibration or Off-Balance

Check the following for

proper installation or

see “Using Your Washer”

section.

Feet may not be in contact with the

ﬂoor and locked.

Front and rear feet must be in ﬁrm contact with ﬂoor, and

washer must be level to operate properly.

Washer may not be level. Check ﬂoor for ﬂexing or sagging. If ﬂooring is uneven, a 3/4"

(19 mm) piece of plywood under your washer will reduce sound.

See “Level the Washer” in Installation Instructions.

Load could be unbalanced. Load dry items in loose heaps evenly around basket wall.

Adding wet items to washer or adding more water to basket

could unbalance washer.

Wash smaller loads to reduce imbalance.

Do not tightly pack. Avoid washing single items.

Use Bulky/Sheets cycle for oversized, non-absorbent items such as

comforters or poly-ﬁlled jackets.

See “Cycle Guide” and “Using Your Washer” in this Use and

Care Guide.

Noises

Clicking or metallic noises Objects caught in washer drain system. Empty pockets before washing. Loose items such as coins could fall

between basket and tub or may block pump. It may be necessary to

call for service to remove items.

It is normal to hear metal items on clothing such as metal snaps,

buckles, or zippers touch against the basket.

Gurgling or humming Washer may be draining water. It is normal to hear the pump making a continuous humming sound

with periodic gurgling or surging as ﬁnal amounts of water are

removed during the Drain/Spin cycles.

Humming Load sensing may be occurring. You may hear the hum of the sensing spins after you have started

the washer. This is normal.

Whirring Basket deceleration may be occurring. You may hear the whirring sound of the basket decelerating. This is

normal.

Water Leaks

Check the following for

proper installation:

Washer not level. Water may splash off basket if washer is not level.

Fill hoses not attached tightly. Tighten ﬁll-hose connection.

Fill hose washers. Make sure all four ﬁll hose ﬂat washers are properly seated.

Drain hose connection. Pull drain hose from washer cabinet and properly secure it to

drainpipe or laundry tub.

Check household plumbing for leaks or

clogged sink or drain.

Water can back up out of a clogged sink or drainpipe. Check all

household plumbing for leaks (laundry tubs, drain pipe, water pipes,

and faucets).

Washer not loaded as recommended. Unbalanced loading can cause basket to be out of alignment

and cause water to splash off tub. See “Using Your Washer”

for loading instructions.

Washer Not Performing As Expected

Not enough water

in washer

Load not completely covered in water. This is normal operation for a high efﬁciency washer. If the Water

Level knob is set to Auto setting, the load will not be completely

under water. The washer senses load sizes and adds correct

amount of water for optimal cleaning.

Use Bulky/Sheets cycle for higher water ﬁll, or set Water Level knob

to Deep Water Wash setting. See “What’s New Under the Lid” and

“Cycle Guide” to match your load with the best cycle.

Run Clean Washer with affresh® cycle to optimize the water level

and wash performance due to soil buildup in washer basket.

First try the solutions suggested here or visit our website at www.maytag.com/product_help -

In Canada www.maytag.ca for assistance and to possibly avoid a service call.

First try the solutions suggested here or visit our website at www.maytag.com/product_help -

In Canada www.maytag.ca for assistance and to possibly avoid a service call.

TROUBLESHOOTING

Washer won’t run or ﬁll,

washer stops working,

or wash light remains

on (indicating that the

washer was unable to ﬁll

appropriately) (cont.)

Check proper electrical supply. Plug power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Ensure there is power to outlet.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Normal washer operation. Lid must be closed for washer to run.

Washer will pause during certain phases of cycle. Do not

interrupt cycle.

Washer may be tightly packed. Remove several items, rearrange load evenly in basket. Close lid and

press START/PAUSE.

Do not add more than 1 or 2 additional items after cycle has started

to avoid tightly packing or unbalancing.

Do not add more water to the washer.

Washer not draining/

spinning, loads are

still wet, or spin light

remains on (indicating that

the washer was

unable to pump out water

within 10 minutes)

Small items may have been caught

in pump or between basket and tub,

which can slow draining.

Empty pockets and use garment bags for small items.

Use a cycle with a low spin speed. Cycles with lower spin speeds remove less water than cycles

with high spin speeds. Use the recommended cycle/spin speed

for your garment. To remove extra water in the load, select

Drain/Spin. Load may need to be rearranged to allow even

distribution of the load in the basket.

The washer may be tightly packed

or unbalanced.

Tightly packed or unbalanced loads may not allow the washer

to spin correctly, leaving the load wetter than normal. Evenly

arrange the wet load for balanced spinning. Select the Drain/

Spin cycle to remove excess water. See “Using Your Washer”

for loading recommendations.

If you experience Possible Causes Solution

Washer Not Performing As Expected (cont.)

Washer won’t run or ﬁll,

washer stops working,

or wash light remains

on (indicating that the

washer was unable to ﬁll

appropriately)

Check for proper water supply. Both hoses must be attached and have water ﬂowing to

inlet valve.

Both hot and cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water ﬂow.

TROUBLESHOOTING

If you experience Possible causes Solution

Washer Not Performing As Expected (cont.)

Washer not draining/

spinning, loads are

still wet or spin light

remains on (indicating that

the washer was

unable to pump out water

within 10 minutes) (cont.)

Check plumbing for correct drain hose

installation. Drain hose extends into

standpipe farther than 4.5" (114 mm).

Check drain hose for proper installation. Use drain hose form

and securely attach to drainpipe or tub. Do not tape over drain

opening. Lower drain hose if the end is higher than 96" (2.4 m)

above the ﬂoor. Remove any clogs from drain hose.

Too much detergent causing suds to

slow or stop draining and spinning.

Always measure and follow detergent directions for your load.

To remove extra suds, select Rinse/Spin. Do not add detergent.

Dry spots on load

after cycle

High speed spins extract more

moisture than your previous washer.

The high spin speeds combined with air ﬂow during the ﬁnal spin

can cause items near the top of the load to develop dry spots

during the ﬁnal spin. This is normal.

Washer may be tightly packed. Use Bulky/Sheets cycle for higher water ﬁll, or set Water Level knob

to Deep Water Wash setting. See “Cycle Guide” to match your load

with the best cycle.

Added extra garments to the load after

the sensing/ﬁll phase.

Add only 1 or 2 additional garments after washer has started.

Incorrect or wrong

wash or rinse

temperatures

Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached to both washer and faucet,

and have both hot and cold water ﬂowing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

Energy saving controlled

wash temperatures.

This washer uses cooler wash and rinse water temperatures

than traditional top-load washers. This includes cooler hot and

warm washes.

Load not rinsed Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached and have water ﬂowing to the

inlet valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.

Not using HE detergent or using too

much HE detergent.

The suds from too much detergent can keep washer from

operating correctly. Always measure detergent and follow

detergent directions based on load size and soil level.

Washer not loaded as recommended. The washer is less efﬁcient at rinsing when load is tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Use cycle designed for the fabrics being washed.

Add only 1 or 2 additional garments after washer has started.

Use Bulky/Sheets cycle for higher water ﬁll, or set Water Level knob

to Deep Water Wash setting. See “Cycle Guide” to match your load

with the best cycle.

Sand, pet hair, lint,

etc. on load after

washing

Heavy sand, pet hair, lint, and

detergent or bleach residues may

require additional rinsing.

Add 2 Rinses to the selected cycle and/or use PowerWash cycle or

Deep Water Wash option.

Load is tangling Washer not loaded as recommended. See “Using Your Washer” section.

Select a cycle with a slower wash action and spin speed;

however, items will be wetter than those using a higher speed spin.

Use Bulky/Sheets cycle for higher water ﬁll, or set Water Level knob

to Deep Water Wash setting. See the “Cycle Guide” to match your

load with the best cycle.

Load garments in loose heaps evenly around the basket wall.

Reduce tangling by mixing types of load items. Use the

recommended cycle for the type of garments being washed.

First try the solutions suggested here or visit our website at www.maytag.com/product_help -

In Canada www.maytag.ca for assistance and to possibly avoid a service call.

TROUBLESHOOTING

If you experience Possible Causes Solution

Washer Not Performing As Expected (cont.)

Not cleaning or

removing stains

Added more water to washer. Washer senses load size and adds correct amount of water.

This is normal and necessary for clothes to move. It is normal

for the wash load to be not completely covered in water.

Added water results in less effective cleaning.

Washer not loaded as recommended. Washer is less efﬁcient at cleaning when load is tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Add only 1 or 2 additional garments after washer has started.

Adding detergent on top of load. Add detergent, oxi products, and color-safe bleach to the

bottom of the basket before adding the load items.

Not using HE detergent or using too

much HE detergent.

The suds from regular detergent can keep washer from operating

correctly.

Use only HE detergent. Be sure to measure correctly.

Always measure detergent and follow manufacturer’s directions

based on load size and soil level.

Not using correct cycle for fabric type. Use a higher soil level cycle option and warmer wash temp

to improve cleaning.

Use PowerWash cycle for tough cleaning. See the “Cycle Guide” to

match your load with the best cycle.

Not using dispensers. Use dispensers to avoid chlorine bleach and fabric

softener staining.

Load dispensers before starting a cycle.

Avoid overﬁlling.

Do not add products directly onto load.

Not washing like colors together. Wash like colors together and remove promptly after the cycle

is complete to avoid dye transfer.

Incorrect dispenser

operation

Clogged dispenser. Load dispensers before starting a cycle.

Use only liquid chlorine bleach in the bleach dispenser. Use only

fabric softener in the fabric softener dispenser.

Fabric Softener knob not set to “Yes”. Set Fabric Softener knob to “Yes” when using fabric softener dispenser.

Fabric damage Sharp items were in pockets during

wash cycle.

Empty pockets, zip zippers, and snap or hook fasteners before

washing to avoid snags and tears.

Strings and straps could have tangled. Tie all strings and straps before starting wash load.

Items may have been damaged

before washing.

Mend rips and broken threads in seams before washing.

Fabric damage can occur if load is

tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Use cycle designed for the fabrics being washed.

Use Bulky/Sheets cycle for higher water ﬁll, or set Water Level knob

to Deep Water Wash setting. See “What’s New Under the Lid” and

“Cycle Guide” to match your load with the best cycle.

Add only 1 or 2 additional garments after washer has started.

Liquid chlorine bleach may have been

added incorrectly.

Do not pour liquid chlorine bleach directly onto load. Wipe up

bleach spills.

Undiluted bleach will damage fabrics. Do not use more than

recommended by manufacturer.

Do not place load items on top of bleach dispenser when loading

and unloading washer.

Garment care instructions may not

have been followed.

Always read and follow garment manufacturer’s care label

instructions. See the “Cycle Guide” to match your load with the

best cycle.

First try the solutions suggested here or visit our website at www.maytag.com/product_help -

In Canada www.maytag.ca for assistance and to possibly avoid a service call.

If you experience Possible Causes Solution

Washer Not Performing As Expected (cont.)

Odors Monthly maintenance not done as

recommended.

See “Washer Care” in Washer Maintenance.

Unload washer as soon as cycle is complete.

Using too much detergent. Be sure to measure correctly. Always follow the

manufacturer’s directions.

See “Washer Care” section.

Lid locked light is

ﬂashing

The lid is not closed. Close the lid. The washer will not start or ﬁll with the lid open.

A cycle was stopped or paused using

the START/PAUSE button.

The washer may still be spinning. The lid will not unlock until the

basket has stopped spinning. This may take several minutes if

washing large loads or heavy fabrics.

Single-dose laundry

packet not dissolving

Adding laundry packet incorrectly. Be sure laundry packet is added to washer basket before adding

clothes. Do not add packet to dispenser. Follow the manufacturer’s

instructions to avoid damage to your garments.

Washer pumps out water

before ﬁnishing cycle

Lid is left open for more than

10 minutes.

Make sure lid is closed before starting a cycle and/or during pre-

wash (soak).

First try the solutions suggested here or visit our website at www.maytag.com/product_help -

In Canada www.maytag.ca for assistance and to possibly avoid a service call.

TROUBLESHOOTING

MAYTAG

LAUNDRY

LIMITED WARRANTY

1. Commercial, non-residential, multiple-family use, or use inconsistent with

published user, operator, or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation,

installation not in accordance with electrical or plumbing codes, or

correction of household electrical or plumbing (i.e. house wiring, fuses,

or water inlet hoses).

4. Consumable parts (i.e. light bulbs, batteries, air or water ﬁlters,

preservation solutions, etc.).

5. Defects or damage caused by the use of non-genuine Maytag parts or

accessories.

6. Conversion of your product from natural gas or L.P. gas or reversal of

appliance doors.

7. Damage from accident, misuse, abuse, ﬁre, ﬂoods, acts of God, or use

with products not approved by Maytag.

8. Repairs to parts or systems to correct product damage or defects caused

by unauthorized service, alteration, or modiﬁcation of the appliance.

9. Cosmetic damage including scratches, dents, chips, and other damage

to appliance ﬁnishes unless such damage results from defects in

materials and workmanship and is reported to Maytag within 30 days.

10. Discoloration, rust, or oxidation of surfaces resulting from caustic

or corrosive environments, including but not limited to, high salt

concentrations, high moisture or humidity, or exposure to chemicals.

11. Pick-up or delivery. This product is intended for in-home repair.

12. Travel or transportation expenses for service in remote locations where an

authorized Maytag servicer is not available.

13. Removal or reinstallation of inaccessible appliances or built-in ﬁxtures (i.e.

trim, decorative panels, ﬂooring, cabinetry, islands, countertops, drywall,

etc.) that interfere with servicing, removal, or replacement of the product.

14. Service or parts for appliances with original model/serial numbers

removed, altered, or not easily determined.

The cost of repair or replacement under these excluded

circumstances shall be borne by the customer.

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS

REQUIRED TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

Name, address, and telephone number

Model number and serial number

A clear, detailed description of the problem

Proof of purchase including dealer or retailer name and address

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair.

Some questions can be addressed without service. Please take a few minutes to review the

Troubleshooting or Problem Solver section of the Use and Care Guide, scan the QR code on

the right to access additional resources, or visit https://www.maytag.com/product_help.

2. All warranty service is provided exclusively by our authorized Maytag Service Providers.

In the U.S. and Canada, direct all requests for warranty service to:

Maytag Customer eXperience Center

In the U.S.A. call 1-800-688-9900. In Canada call 1-800-807-6777.

If outside the 50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies.

FIRST YEAR LIMITED WARRANTY

(PARTS AND LABOR)

For one year from the date of purchase, when this major

appliance is installed, operated, and maintained according to

instructions attached to or furnished with the product, Maytag

brand of Whirlpool Corporation or Whirlpool Canada LP

(hereafter “Maytag”) will pay for factory specified parts and

repair labor to correct defects in materials or workmanship

that existed when this major appliance was purchased, or

at its sole discretion replace the product. In the event of

product replacement, your appliance will be warranted by the

remaining term of the original unit’s warranty period.

SECOND THROUGH TENTH YEAR LIMITED

WARRANTY (DRIVE MOTOR AND WASH BASKET

ONLY - LABOR NOT INCLUDED)

In the second through tenth years from the date of original

purchase, when this major appliance is installed, operated, and

maintained according to instructions attached to or furnished

with the product, Maytag will pay for factory specified parts for

the following components to correct non-cosmetic defects in

materials or workmanship in these parts that prevent function

of this major appliance and that existed when this major

appliance was purchased. This is a limited 10 year warranty on

the below named parts only and does not include repair labor.

n Drive Motor n Wash Basket (Side Walls Only)

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS

LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS

PROVIDED HEREIN. Service must be provided by a Maytag

designated service company. This limited warranty is valid

only in the United States or Canada and applies only when

the major appliance is used in the country in which it was

purchased. This limited warranty is effective from the date of

original consumer purchase. Proof of original purchase date is

required to obtain service under this limited warranty.

https://www.maytag.com/product_help

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces

do not allow limitations on the duration of implied warranties of merchantability or ﬁtness, so this limitation may not apply to you. This warranty

gives you speciﬁc legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the

exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives

you speciﬁc legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Maytag makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Maytag or your retailer about buying an extended warranty.

11/14

TEN YEAR LIMITED WARRANTY

WHAT IS COVERED

WHAT IS NOT COVERED

SÉCURITÉ DE LA LAVEUSE

QUOI DE NEUF SOUS LE COUVERCLE?

Votre nouvelle laveuse fonctionne différemment de votre précédente laveuse de type agitateur.

Choix du détergent approprié

Utiliser uniquement des détergents haute efﬁcacité. L’emballage

portera la mention “HE” ou “High Efﬁciency” (haute efﬁcacité). Il est

probable que l’utilisation d’un détergent non HE prolongera la durée

des programmes et réduira la performance de rinçage. Ceci peut

aussi entraîner des malfunctions de composants et, avec le temps,

une accumulation de moisissure. Les détergents HE devraient

produire peu de mousse et se dissoudre rapidement pour produire

une quantité de mousse idéale pour une performance optimale. Ils

devraient retenir les particules de saleté en suspension aﬁn qu’elles

ne se redéposent pas sur les vêtements propres. Les détergents

identiﬁés HE ne comportent pas tous une formule identique et ne

produisent pas tous la même quantité de mousse. Par exemple, les

détergents HE naturels, organiques et faits maison peuvent produire

une plus grande quantité de mousse. Toujours suivre les instructions

du fabricant pour déterminer la quantité de détergent à utiliser.

Utiliser uniquement un détergent haute efﬁcacité (HE).

Sons normaux prévisibles

Au cours des différents stades du programme de lavage, vous

entendrez peut-être des bruits que votre laveuse précédente

ne produisait pas. Par exemple, vous entendrez peut-être un

cliquetis au début de l’étape d’essorage lorsque le système de

verrouillage du couvercle effectue un test automatique. Différents

bourdonnements et bruits de frottements rythmiques se produiront

à mesure que l’agitateur évalue l’équilibre de la charge et qu’il la

déplace. Parfois, il est possible que la laveuse soit complètement

silencieuse, lorsqu’elle détermine le niveau d’eau adéquat ou

qu’elle laisse tremper les vêtements.

Verrouillage du couvercle

Pour permettre des essorages à vitesse plus élevée, le couvercle

se verrouille et le témoin de couvercle verrouillé s’allume. Lorsque

ce témoin lumineux s’allume, cela signiﬁe que le couvercle est

verrouillé et ne peut être ouvert. Lorsque ce témoin lumineux

clignote, cela signiﬁe que la laveuse effectue une pause. Lorsque

ce témoin lumineux est éteint, cela signiﬁe qu’on peut ouvrir le

couvercle. Une fois qu’un programme a commencé, la laveuse

se remplit au niveau d’eau approprié. Quand la laveuse est faite

remplir, l’agitation va commencer. Si l’on doit ouvrir le couvercle

pour ajouter un vêtement après cette étape, le couvercle de la

demeurera déverrouillé pendant toute la partie de l’agitation de

l’étape de lavage. Le programme fait une pause automatiquement

quand le couvercle est ouvert, et le programme recommencera

après la fermeture du couvercle. Le couvercle se verrouille avant

le début de l’étape d’essorage. Si l’on doit pauser ou arrêter après

cette étape, il faut appuyer sur START/PAUSE (mise en marche/

pause) puis attendre que le couvercle se déverrouille. Le couvercle

se déverrouille uniquement une fois que le mouvement de la

laveuse a cessé. Selon le moment où l’on souhaite suspendre le

programme, le couvercle peut mettre entre quelques secondes et

plusieurs minutes à se déverrouiller. Appuyer sur START/PAUSE

(mise en marche/pause) pour poursuivre le programme.

Options de niveau d’eau

Régler le bouton Water Level (niveau d’eau) sur le réglage

Auto Sensing (détection automatique) et la laveuse ajuste

automatiquement le niveau d’eau en fonction de la taille de la

charge. Régler le bouton Water Level (niveau d’eau) sur le réglage

Deep Water Wash (lavage à l’eau profonde) et la laveuse se remplit

jusqu’au niveau d’eau maximal.

Détection

Cette laveuse effectue une série d’essorages pour contrôler

l’équilibre de la charge. Durant cette période, une série de cliquetis

et un bruit de frottements rythmiques indiquent que la technologie

de détection détermine si la charge est déséquilibrée.

Rinçage par vaporisation

Certains programmes utilisent l’option rinçage par vaporisation par

défaut. Au cours de ces programmes, on entend l’eau pénétrer

dans la laveuse tandis que la cuve tourne, ce qui permet à l’eau

de rinçage de pénétrer les vêtements. Consulter le “Guide de

programmes” pour plus de détails.

IMPORTANT :

■ Le couvercle doit être fermé avant que le panier de la laveuse se remplisse et que le programme de lavage se mette en marche. Si le

couvercle est ouvert et que le remplissage s’arrête, fermer le couvercle et appuyer sur le bouton START/PAUSE (mise en marche/pause)

pour terminer le programme.

■ Options rinçage doivent être réglées sur une rinçage à l’assouplissant ou deux rinçages avec l’assouplissant lors de l’utilisation

d’assouplissant pour tissu dans le distributeur d’assouplissant. Cela garantit que l’assouplissant est ajouté au bon moment

dans la phase de rinçage et est uniformément répartie.

TABLEAU DE COMMANDE ET CARACTÉRISTIQUES

1 RINSE WITH FABRIC SOFTENER

(rinçage unique avec assouplissant)

Cette option doit être sélectionnée si l’on utilise

del’assouplissant pour tissu durant un programme. Ceci

garantit que l’assouplissant pour tissu est ajouté au bon

moment lors du rinçage pour être correctement distribué.

2 RINSES WITH FABRIC SOFTENER

(double rinçage avec assouplissant)

Cette option doit être sélectionnée si l’on utilise

del’assouplissant pour tissu durant un programme et 2

Rinses (double rinçage).

WATER LEVEL (niveau d’eau)

Réglez le bouton de niveau d’eau pour le réglage automatique

de détection et de la laveuse détectera automatiquement le

niveau d’eau approprié pour la taille et le type de charge.

Réglez le bouton de niveau d’eau à Deep Water Wash

(lavage à niveau d’eau élevé) et la laveuse va remplir le

niveau d’eau maximal.

REMARQUE: Attendez-vous à des cycles plus longs dus aux

délais de remplissage étendus lorsque vous utilisez l’option

Deep Water Wash (lavage à niveau d’eau élevé).

START/PAUSE BUTTON

(bouton mise en marche/pause)

Appuyer sur ce bouton pour démarrer le programme

sélectionné, puis appuyer de nouveau pour suspendre le

programme et déverrouiller le couvercle.

REMARQUE : Si la laveuse tourne, cela peut prendre plusieurs

minutes pour déverrouiller le couvercle.

PROGRESS LIGHTS (témoins lumineux de progrés)

Les Progress Lights (témoins lumineux de progrés) indiquent la

progression du programme. À chaque étape du processus, il est

possible que l’on remarque des pauses ou des sons différents

de ceux de votre laveuse précédente.

SENSING (détection)

Lorsque le bouton START/PAUSE (mise en marche/pause)

est enfoncée et le bouton de niveau d’eau est réglé sur

détection automatique, la laveuse se remplir et commencer

détection pour déterminer la taille de la charge et de

l’équilibre. Une seul fois détection est terminée, la laveuse

va remplir le appropriée niveau de la taille de la charge

détectée puis commencent la phase de lavage du cycle.

SOIL LEVEL (niveau de saleté)

Sélectionner le réglage le plus adapté à votre charge. Pour les

tissus très sales, sélectionner Heavy Soil Level (niveau de saleté

important) pour prolonger la durée de lavage. Pour les tissus

peu sales, sélectionner Light Soil Level (niveau de saleté faible)

pour abréger la durée de lavage. Le réglage de niveau de saleté

faible aidera à réduire l’emmêlement et le froissement.

WASH TEMP (température de lavage)

La fonction Wash Temp (température de lavage) détecte et

maintient une température uniforme de l’eau en régulant le débit

d’arrivée d’eau chaude et d’eau froide.

Sélectionner une température de lavage en fonction du type de

tissu et de saleté à laver. Pour des résultats optimaux, suivre les

instructions sur l’étiquette du vêtement et utiliser la température

d’eau de lavage la plus chaude possible qui reste sans danger

pour le tissu.

•Sur certains modèles et pour certains programmes, les

températures utilisées pour l’eau chaude et l’eau tiède peuvent

être inférieures aux températures utilisées par votre précédente

laveuse.

• Même pour les lavages dont la température a été réglée sur

Cool (frais) ou Cold (froid), il est possible que de l’eau tiède soit

ajoutée à la laveuse pour maintenir une température minimale.

Tout les rinçages sont froids.

WASH CYCLE KNOB

(bouton de programme de lavage)

Utiliser le bouton de programme de lavage pour sélectionner

les programmes disponibles sur la laveuse. Tourner le bouton

de programme pour sélectionner un programme correspondant

à la charge de linge. Voir “Guide de programmes” pour des

descriptions détaillées.

RINSE OPTIONS (options de rinçage)

Il est possible d’ajouter les options suivantes à la plupart

des programmes. Voir “Guide de programmes” pour plus

de détails.

1 RINSE (rinçage unique)

Cette option permet de limiter le nombre de rinçages

d’unprogramme à un seul rinçage.

2 RINSES (double rinçage)

On peut utiliser cette option pour ajouter automatiquement

un second rinçage à la plupart des programmes.

Certaines caractéristiques et options ne sont pas disponibles sur certains modèles.

L’apparence des appareils peut varier.

4 5

La page charge ...

Maytag MVWC565FW MVWC565FW Use and Care EN

Marque: Maytag

Modèle: MVWC565FW

Catégorie: Machines à laver

Taper: MVWC565FW Use and Care EN

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MVWC565FW

Maytag MVWC565FW MVWC565FW Use and Care EN

Maytag MVWC565FW MVWC565FW Use and Care EN

dans d''autres langues

Documents connexes

Autres documents