Maytag MVWC465HW2 Le manuel du propriétaire

Marque: Maytag

Modèle: MVWC465HW2

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Ce manuel convient également à

W11159204A

W11159210A-SP

Designed to use only

HE (High Efﬁciency) detergents.

Conçue pour l’utilisation d’un

détergent haute efﬁcacité seulement.

TOP-LOADING

HIGH EFFICIENCY

WASHER

USE AND CARE GUIDE

Table of Contents

WASHER SAFETY .................................................................. 2

WHAT’S UNDER THE LID ..................................................... 3

CONTROL PANEL AND FEATURES ................................... 4

CYCLE GUIDE ..........................................................................6

USING YOUR WASHER ........................................................ 8

WASHER MAINTENANCE .................................................. 11

TROUBLESHOOTING ..........................................................13

WARRANTY ............................................................................18

ASSISTANCE OR SERVICE .........................BACK COVER

Table des matières

SÉCURITÉ DE LA LAVEUSE ..............................................19

CE QUI EST SOUS LE COUVERCLE ................................ 20

TABLEAU DE COMMANDE

ET CARACTÉRISTIQUES ....................................................21

GUIDE DE PROGRAMMES ...............................................23

UTILISATION DE LA LAVEUSE ..........................................25

ENTRETIEN DE LA LAVEUSE ............................................ 28

DÉPANNAGE ..........................................................................30

GARANTIE ............................................................................... 36

ASSISTANCE OU SERVICE ....COUVERTURE ARRIÈRE

GUIDE D’UTILISATION

ET D’ENTRETIEN

DE LA LAVEUSE

HAUTE EFFICACITÉ

AVEC CHARGEMENT

PAR LE DESSUS

Para una versión de estas instrucciones en español, visite www.maytag.com

WASHER SAFETY

WHAT’S UNDER THE LID

Use only High Efﬁciency (HE) detergent.

IMPORTANT:

■ The lid must be closed before the washer basket ﬁlls with water and for the wash cycle to start. If the lid is opened, the cycle pauses

and all ﬁlling/agitation motion halts. Once the lid is closed, the cycle automatically resumes. However, if the Start/Pause/Cancel button

is pressed prior to opening the lid, the lid must be closed and the Start/Pause/Cancel button pressed again to resume the cycle.

■ Rinse Option must be set to either 1 Rinse with Fabric Softener or 2 Rinses with Fabric Softener when using fabric softener in the

fabric softener dispenser. This ensures that fabric softener is added at the correct time in the rinse phase and is evenly distributed.

Lid Lock

To allow for higher spin speeds, the lid will lock and the Lid

Locked light will turn on. When this light is lit, the lid is locked and

cannot be opened without pausing the cycle. When this light is

blinking, the washer is paused. When this light is off, the lid can

be opened. After the cycle has started, the washer will ﬁll to the

appropriate water level. On select cycles, agitation will occur while

the basket is ﬁlling with water. This is normal. When the washer is

done ﬁlling, it will begin the wash phase. If you need to open the

lid to add a garment after this point, the lid will remain unlocked

during the entire agitation portion of the wash phase. The cycle

will automatically pause when the lid is opened, and the cycle

will resume once the lid is closed. The lid will lock before the spin

phase begins. If you need to pause or stop after this point, you

must press the START/PAUSE/CANCEL button and wait for the

lid to unlock. The lid will only unlock after washer movement has

stopped. Depending on when in the cycle you try to pause, it may

take from several seconds to several minutes for the lid to unlock.

Press START/PAUSE/CANCEL to resume the cycle.

Sensing

This washer automatically senses the load size for most cycles,

and chooses an appropriate water level according to the load size

detected. This washer also performs a series of spins to check

for load balance. During this time, a series of clicks and a whirring

noise signal that sensing technology is determining if there is an

off-balance load.

Water Level Options

Set the Water Level knob to the Auto Sensing setting and

the washer automatically adjusts the water level to the load size.

Set the Water Level knob to the Deep Water Wash setting and

the washer automatically adds more water to any cycle at any time

during the wash process.

Normal Sounds You Can Expect

At different stages of the wash cycle, you may hear sounds

and noises that are different from those of your previous washer.

For example, you may hear a clicking and hum at the beginning

of the spin phase, as the lid lock goes through a self-test. There

will be different kinds of humming sounds as the HE agitator tests

for load balance or moves the load. And sometimes, you may hear

nothing at all, as the washer determines the correct water level

for your load or allows time for clothes to soak.

Spray Rinse

Select cycles default to a spray rinse. During these cycles, you

will hear water enter the washer as the tub spins, allowing the rinse

water to penetrate clothes. Check the “Cycle Guide” for details.

Choosing the Right Detergent

Use only High Efﬁciency detergents. The package will be marked

“HE” or “High Efﬁciency.” Using non-HE detergent will likely result

in longer cycle times and reduced rinsing performance. It may also

result in component malfunction and, over time, buildup of mold or

mildew. HE detergents should be low-sudsing and quick-dispersing

to produce the right amount of suds for the best performance. They

should hold soil in suspension so it is not redeposited onto clean

clothes. Not all detergents labeled as High Efﬁciency are identical

in formulation and their ability to reduce suds. For example, natural,

organic, or homemade HE detergents may generate a high level

of suds. Always follow the detergent manufacturer’s instructions

to determine the amount of detergent to use.

CONTROL PANEL AND FEATURES

WATER LEVEL

Set the Water Level knob to the Auto Sensing setting and the

washer will automatically sense the appropriate water level for

the load size and type.

Set the Water Level knob to the Deep Water Wash setting and

the washer will automatically add more water to any cycle at any

time during the wash process.

NOTE: Expect longer cycle times due to extended ﬁ ll times

when using the Deep Water Wash option.

START/PAUSE/CANCEL BUTTON

Press to start the selected cycle. Press again to pause the

cycle and unlock the lid. Close the lid and press to restart

the cycle. Press and hold to cancel a cycle and pump out

the washer.

NOTE: If the washer is spinning, it may take several minutes

to unlock the lid.

PROGRESS LIGHTS

The Progress Lights show the progress of a cycle. At each

stage of the process, you may notice sounds or pauses that

are different from your previous washer.

SENSING/FILL

When the Start/Pause/Cancel button is pressed and the

Water Level knob is set to Auto Sensing, the washer will

ﬁ ll and begin sensing to determine load size and balance.

A short but noticeable pause in the cycle action occurs

during sensing. This is normal.

Once sensing is complete, the washer will ﬁ ll to the

appropriate level for the detected load size and, on select

cycles, agitation will occur during ﬁ lling. This, too, is normal.

When the washer is done ﬁ lling, it will begin the wash phase

of the cycle. To ensure that the most accurate load size is

detected, avoid opening the lid during the “Sensing” phase.

NOTE: Sensing and wash phases will be paused by opening

the unlocked lid. Close the lid to resume the cycle. If the lid is

left open for more than 10 minutes, the washer will cancel the

cycle and pump out the water.

SOIL LEVEL

Select the setting most suitable for your load. For heavily soiled

and sturdy fabrics, select Heavy soil level for more wash time.

For lightly soiled and delicate fabrics, select Light soil level

for less wash time. A lighter soil level setting will help reduce

tangling and wrinkling.

WASH TEMP

Wash Temp senses and maintains uniform water temperatures

by regulating incoming hot and cold water.

Select a wash temperature based on the type of fabric and

soils being washed. For best results, use the warmest wash

water safe for your fabric, as speciﬁ ed by the garment label

instructions.

• On some models and cycles, warm and hot water may be

cooler than your previous washer.

• Even in a cold- and cool-water wash, some warm water may

be added to the washer to maintain a minimum temperature.

All rinses are cold.

WASH CYCLE KNOB

Use the Wash Cycle knob to select cycles on your washer.

See “Cycle Guide” for detailed descriptions of cycles.

RINSE OPTION

The following options may be added to most cycles.

See “Cycle Guide” for additional details.

1 RINSE

This option is used to limit a cycle to one rinse.

2 RINSES

This option can be used to automatically add a second

rinse to all wash cycles.

1 RINSE WITH FABRIC SOFTENER

This option must be selected if using fabric softener during

a cycle. It ensures that fabric softener is added at the correct

time in the rinse for even distribution.

2 RINSES WITH FABRIC SOFTENER

This option turns on both the Fabric Softener and the

2 Rinses option.

Not all features and options are available on all models.

Appearance may vary.

4 5

WASH

The washer will ﬁ ll to the correct water level based on the

load size and the Water Level selection. Certain cycles may

agitate during the ﬁ ll process to boost cleaning. When the

wash cycle begins, you will hear the HE agitator increase

speed. The motor sounds may change at different stages

in the wash cycle while the washer performs different

wash actions.

NOTE: The lid will automatically lock after the wash phase

completes and before the initial spinout occurs, and will

remain locked for the rest of the cycle.

RINSE

Certain cycles use a spray rinse, which adds water to the

tub while the basket spins. You may hear the motor turning

on brieﬂ y (short hum) to move the basket while ﬁ lling. In

some cases, you may also hear sounds similar to the wash

cycle as the washer ﬁ lls, rinses, and moves the load.

SPIN

The washer spins the load at increasing speeds for proper

water removal based on the selected cycle and spin speed.

DONE

Once the cycle is complete, the lid will unlock and this light

will come on. For best results, promptly remove the load.

LID LOCKED

The Lock feature allows for higher spin

speeds. When lit, the lid is locked and

cannot be opened without pausing the

cycle. When the light is off, the lid can

be opened.

To open the lid after it has been locked, press START/

PAUSE/CANCEL. The lid will unlock once the washer

movement has stopped. This may take several minutes

if the load was spinning at high speed. Press START/

PAUSE/CANCEL while the lid is closed to resume

the cycle.

Sturdy fabrics,

colorfast items,

towels, jeans

PowerWash

Hot

Warm

Cool

Cold

Tap Cold

High Use this cycle for heavily soiled or sturdy items. Water-level

sensing process may take longer for some items than for others

because they will absorb more water than other fabric types.

Heavily soiled

white fabrics

Whites

with Soak

‡

Hot

Warm

Cool

Cold

Tap Cold

High This cycle, when used with chlorine bleach, improves whitening

of soiled white fabrics.

‡

To enhance cleaning, select Whites with Soak, which

automatically adds about 10 minutes of soak time after the

ﬁll phase, and then automatically runs the Whites cycle.

Large items such

as sheets, sleeping

bags, small

comforters, jackets,

small, washable rugs

Bulky Items Hot

Warm

Cool

Cold

Tap Cold

Low Use this cycle to wash large items such as jackets and small

comforters. The washer will ﬁll with enough water to wet down

the load before the wash portion of the cycle begins and uses

a higher water level than other cycles.

Cottons, linens, and

mixed loads

Normal Hot

Warm

Cool

Cold

Tap Cold

High Use this cycle for normally soiled cottons and mixed loads.

Bright and darkly

colored cottons

and mixed loads

Colors

with Soak

Hot

Warm

Cool

Cold

Tap Cold

High Use this cycle to wash darks and colors, including mixed loads

and activewear.

To enhance cleaning, select Colors with Soak, which

automatically adds about 10 minutes of soak time after the

ﬁll phase, and then automatically runs the Colors cycle.

Machine-wash silks,

handwash fabrics

Delicates Hot

Warm

Cool

Cold

Tap Cold

Low Use this cycle to wash lightly soiled items indicating “Machine

Washable Silks” or “Gentle” cycle on the care label. Place small

items in mesh garment bags before washing. This cycle uses a

higher, preset water level.

CYCLE GUIDE

For best fabric care, choose the cycle that best ﬁts the load being washed.

Recommended settings for best performance are shown in Bold.

Not all cycles and options are available on all models. Not all settings and options are available on each cycle.

NOTE: If you are using fabric softener, be sure to select either 1 Rinse with Fabric Softener or 2 Rinses with Fabric Softener.

**All rinses are cold.

**Spin speed is integrated into the cycle and cannot be selected or modiﬁed.

†

Efﬁcient use of resources, such as energy and water.

Items to wash: Cycle: Wash Temp:* Spin

Speed:**

Cycle Details:

Cleaning

Gentleness

Efciency

†

Good

Best

Cleaning

Gentleness

Efciency

†

Good

Best

Cleaning

Gentleness

Efciency

†

Good

Best

Cleaning

Gentleness

Efciency

†

Good

Best

Cleaning

Gentleness

Efciency

†

Good

Best

Cleaning

Gentleness

Efciency

†

Good

Best

Small loads, cottons,

polyester, permanent

press

Quick Wash Hot

Warm

Cool

Cold

Tap Cold

High Use this cycle to wash small, lightly soiled loads of two or three

items that are needed in a hurry.

Swimsuits and items

requiring rinsing

without detergent

Rinse &

Spin

Cold rinse only High Combines a rinse and high-speed spin for loads requiring an

additional rinse cycle. Use this cycle to complete a load after

power interruption or for loads that require rinsing only.

Hand-washed items

or dripping-wet items

Drain &

Spin

N/A High This cycle uses a spin to shorten drying times for heavy fabrics

or special-care items washed by hand. Use this cycle to drain

washer after canceling a cycle or completing a cycle after a

power failure.

No clothes in washer Clean Washer

with affresh

Hot Low Use this cycle every 30 washes to keep the inside of your

washer fresh and clean. This cycle uses a higher water level.

Use with affresh

Washer Cleaner tablet or liquid chlorine

bleach to thoroughly clean the inside of your washer. This cycle

should not be interrupted. See “Washer Care.”

IMPORTANT: Do not place garments or other items in the

washer during the Clean Washer with affresh

cycle. Use this

cycle with an empty wash tub.

Items to wash: Cycle: Wash Temp:* Spin

Speed:**

Cycle Details:

Cleaning

Gentleness

Efciency

†

Good

Best

NOTE: If you are using fabric softener, be sure to select either 1 Rinse with Fabric Softener or 2 Rinses with Fabric Softener.

**All rinses are cold.

**Spin speed is integrated into the cycle and cannot be selected or modiﬁed.

†

Efﬁcient use of resources, such as energy and water.

USING YOUR WASHER

• Empty pockets. Loose change, buttons, or any small object

can pass under the HE agitator and become trapped, causing

unexpected sounds.

• Sort items by recommended cycle, water temperature,

and colorfastness.

• Separate heavily soiled items from lightly soiled.

• Separate delicate items from sturdy fabrics.

• Do not dry items if stains remain after washing, because

heat can set stains into fabric.

• Treat stains promptly.

• Close zippers, fasten hooks, tie strings and sashes, and

remove non-washable trim and ornaments.

• Mend rips and tears to avoid further damage to items during

washing.

Helpful Tips:

• When washing water-proof or water-resistant items,

load evenly.

• Use mesh garment bags to help avoid tangling when washing

delicate or small items.

• Turn knits inside out to avoid pilling. Separate lint-takers from

lint-givers. Synthetics, knits, and corduroy fabrics will pick up

lint from towels, rugs, and chenille fabrics.

NOTE: Always read and follow fabric care label instructions

to avoid damage to your items.

1. Sort and prepare your laundry

Add a measured amount of HE

detergent or single-dose laundry packet

into the basket.

If using Oxi-type boosters, color-safe

bleach, or fabric-softener crystals, add

to the bottom of the washer basket before adding clothes.

IMPORTANT: Use only High Efﬁ ciency detergents. The

package will be marked “HE” or “High Efﬁ ciency.” Using regular

detergent will likely result in longer cycle times and reduced

rinsing performance. It may also result in component failures and

noticeable mold or mildew. HE detergents are made to produce

the right amount of suds for the best performance.

NOTE: Follow the manufacturer’s instructions to determine the

amount of laundry products to use.

2. Add laundry products

5. Add fabric softener

Pour a measured amount of liquid fabric

softener into dispenser; always follow

manufacturer’s directions for correct amount

of fabric softener based on your load size.

Dilute liquid fabric softener by ﬁ lling the

dispenser with warm water until liquid reaches the underside

of the rim. See max ﬁ ll line arrows.

IMPORTANT: The Rinse Option knob must be set to either

1 Rinse with Fabric Softener or 2 Rinses with Fabric Softener

when using fabric softener in the fabric softener dispenser. This

ensures that fabric softener is added at the correct time in the

rinse phase and is evenly distributed.

Adding Liquid Fabric Softener Manually to Wash Load

During the ﬁ nal rinse, wait until the washer has completed ﬁ lling

and press the START/PAUSE/CANCEL button to pause the

washer. Lift the lid and add the measured, recommended amount

of liquid fabric softener. Do not use more than the recommended

amount. Close the lid and press the START/PAUSE/CANCEL

button again to start the washer.

4. Add liquid chlorine bleach

to dispenser

Liquid

Chlorine Bleach

Do not overﬁ ll, dilute, or use more than 1 cup (236 mL). Do not

use color-safe bleach or Oxi products in the same cycle with

liquid chlorine bleach.

Turn cycle knob to choose your wash cycle. For more

information, see “Cycle Guide.”

6. Select cycle

3. Load laundry into washer

Load garments in loose heaps evenly around

basket wall. For best results, do not pack

the load tightly. Do not wrap large items

such as sheets around the HE agitator;

load them in loose piles around the sides

of the basket. Try mixing different-sized

items to reduce tangling.

IMPORTANT: Do not tightly pack or force items into washer.

Items need to move freely for best cleaning and to reduce

wrinkling and tangling.

MAX FILL

Fabric softener

Water

Wash Temp Suggested Fabrics

8. Select wash temperature

Once you select a cycle, select the wash temperature

by turning the Wash Temp knob to the desired setting.

Always read and follow fabric care label instructions to avoid

damage to your items.

9. Select rinse option and water level

Select the number of rinses by turning the Rinse Option knob to

the desired setting.

IMPORTANT: The Rinse Option knob must be set to an option

“with Fabric Softener” when using the fabric softener dispenser.

This ensures that fabric softener is added at the correct time in

the rinse for even distribution.

Set the Water Level knob to the Auto Sensing setting and the

washer will automatically sense the appropriate water level for

the load size and type.

Set the Water Level knob to the Deep Water Wash setting and

the washer will automatically add more water to any cycle at any

time during the wash cycle.

NOTE: The cycle will be longer due to extended ﬁ ll times when

using the Deep Water Wash setting.

10. Press START/PAUSE/CANCEL

to begin wash cycle

Press START/PAUSE/CANCEL to start the wash cycle. When

the cycle has ﬁ nished, the Done progress light will light. Promptly

remove garments after cycle has completed to avoid odor, reduce

wrinkling, and avoid rusting of metal hooks, zippers, and snaps.

Unlocking the lid to add garments

If you need to add one or two missed garments after the wash

has started, simply open the lid and this will pause the cycle.

After adding the garments, simply close the lid and the cycle will

resume. The washer may add some additional water to offset the

added garments.

If, instead, you press Start/Pause/Cancel to pause the cycle

and then open the lid to add garments, you will need to press

Start/Pause/Cancel after closing the lid to resume the cycle.

NOTE: Washer will not ﬁ ll with the lid open.

IMPORTANT: If lid is left open for more than 10 minutes, the

water will pump out automatically.

Manual soak

If you would like to manually soak your garments at any time

during the wash portion of the cycle, press START/PAUSE/

CANCEL and leave the lid closed. Once your desired soak time

has elapsed, press START/PAUSE/CANCEL again to continue

the cycle. As long as the lid remains closed, your soak time can

be longer than 10 minutes. However, if the lid is opened during

the soak and remains open for more than 10 minutes, the water

will pump out automatically.

Cool

Warm water is added to assist in

soil removal and to help dissolve

detergents.

Cool is slightly warmer than Cold.

Dark colors that

bleed or fade

Light soils

Hot

Some cold water is added to save

energy. This may be cooler than your

hot water heater setting.

Warm

Some cold water will be added, so

this may be cooler than what your

previous washer provided.

Cold

Warm water may be added to assist

in soil removal and to help dissolve

detergents.

Whites and pastels

Durable items

Heavy soils

Bright colors

Moderate to light soils

Colors that bleed

or fade

Light soils

Dark colors that

bleed or fade

Light soils

Tap Cold

This is the temperature

from your faucet.

7. Select soil level

Once you select a cycle, select the soil level by turning the Soil

Level knob to the desired setting.

WASHER MAINTENANCE

Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Periodically inspect and replace inlet hoses

if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of replacement

on the label with a permanent marker.

NOTE: This washer does not include inlet hoses. See the

Installation Instructions for more information.

WATER INLET HOSES

WASHER CARE

Recommendations to Help Keep Your Washer

Clean and Performing at its Best

1. Always use High Efﬁ ciency (HE) detergents and follow the

detergent manufacturer’s instructions regarding the amount

of detergent to use. Never use more than the recommended

amount because that may increase the rate at which

detergent and soil residue accumulate inside your washer,

which in turn may result in undesirable odor.

2. Use warm and hot wash water settings sometimes (not

exclusively cold-water washes) because they do a better

job of controlling the rate at which soils and detergent

accumulate.

3. Always leave the washer lid open between uses to help dry

out the washer and prevent the buildup of odor-causing

residue.

Cleaning Your Top Loading Washer

Read these instructions completely before beginning the

routine cleaning processes recommended below. This washer

maintenance procedure should be performed, at a minimum,

once per month or every 30 wash cycles, whichever occurs

sooner, to control the rate at which soils and detergent may

otherwise accumulate in your washer.

Cleaning the Inside of the Washer

To keep your washer odor-free, follow the usage instructions

provided above and use this recommended monthly cleaning

procedure:

Clean Washer Cycle

This washer has a special cycle that uses higher water volumes

in combination with affresh

Washer Cleaner or liquid chlorine

bleach to clean the inside of the washer.

Begin procedure

1. affresh

Washer Cleaner Cycle Procedure

(Recommended for Best Performance):

a. Open the washer lid and remove any clothing or items.

b. Place an affresh

Washer Cleaner tablet in the bottom

of the washer basket.

c. Do not place an affresh

Washer Cleaner tablet in the

detergent dispenser.

d. Do not add any detergent or other chemical to the washer

when following this procedure.

e. Close the washer lid.

f. Select the cycle recommended for cleaning the inside

of the washer.

g. Press the START/PAUSE/CANCEL button to start

the cycle.

NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, press START/PAUSE/CANCEL once. After

the cycle has stopped, run a Rinse & Spin cycle to rinse

cleaner from washer.

WASHER CARE (cont.)

2. Chlorine Bleach Procedure (Alternative):

a. Open the washer lid and remove any clothing or items.

b. Add 1 cup (236 mL) of liquid chlorine bleach to the bleach

compartment.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause washer damage

over time.

c. Close the washer lid.

d. Do not add any detergent or other chemical

to the washer when following this procedure.

e. Select the cycle recommended for cleaning the inside

of the washer.

f. Press the START/PAUSE/CANCEL button to start

the cycle.

NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, press START/PAUSE/CANCEL once. After

the cycle has stopped, run a Rinse & Spin cycle to rinse

bleach from washer.

Description of Clean Washer Cycle Operation:

1. This cycle will ﬁ ll to a water level higher than in normal wash

cycles to provide rinsing at a level above the water line for

normal wash cycle.

2. During this cycle, there will be some agitation and spinning

to increase the removal of soils.

After this cycle is complete, leave the lid open to allow for better

ventilation and drying of the washer interior.

Cleaning the Dispensers

After a period of using your washer, you may ﬁ nd some residue

buildup in the washer’s dispensers. To remove residue from the

dispensers, wipe them with an affresh

Machine Cleaning Wipe

or a damp cloth and towel dry either before or after you run the

Clean Washer cycle. Do not attempt to remove the dispensers

or trim for cleaning. The dispensers and trim are not removable.

If your model has a dispenser drawer, however, remove the

drawer and clean it before or after you run the Clean Washer

cycle. Use an all-purpose surface cleaner, if needed.

Cleaning the Outside of the Washer

Use an affresh

Machine Cleaning Wipe, a soft, damp cloth,

or a sponge to wipe away any spills. Use an affresh

Machine

Cleaning Wipe or only mild soaps or cleaners when cleaning

external washer surfaces.

IMPORTANT: To avoid damaging the washer’s ﬁ nish,

do not use abrasive products.

Operate your washer only when you are home. If moving, or

not using your washer for a period of time, follow these steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer, to avoid ﬂ ooding due

to water-pressure surge.

WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer

where it will not freeze. Some water may stay in hoses, and

freezing can damage washer. If storing or moving during

freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain

water inlet hoses.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run

washer on Rinse & Spin cycle for about 30 seconds to mix

antifreeze and remaining water.

3. Unplug washer or disconnect power.

NON-USE AND VACATION CARE

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain

water inlet hoses.

2. If washer will be moved during freezing weather, follow

“Winter Storage Care” directions before moving.

3. Disconnect drain hose from drain system and drain any

remaining water into a pan or bucket. Disconnect drain

hose from back of washer.

4. Unplug power cord.

5. Place inlet hoses and drain hose inside washer basket.

6. Drape power cord over edge and into washer basket.

7. Place packing tray from original shipping materials back

inside washer. If you do not have packing tray, place heavy

blankets or towels into basket opening. Close lid and place

tape over lid and down front of washer. Keep lid taped

until washer is placed in new location. Transport washer

in upright position.

REINSTALLING/USING WASHER AGAIN

To reinstall washer after non-use, vacation, winter storage,

or moving:

1. Refer to Installation Instructions to locate, level, and

connect washer.

2. Before using again, run washer through the following

recommended procedure:

To use washer again:

1. Flush water pipes and hoses. Reconnect water inlet hoses.

Turn on both water faucets.

2. Plug in washer or reconnect power.

3. Run washer through Bulky Items cycle to clean washer

and remove any antifreeze. Use half the manufacturer’s

recommended amount of detergent for a medium-size load.

TROUBLESHOOTING

If you experience Possible Causes Solution

Vibration or Off-Balance

Check the following for

proper installation or

see “Using Your Washer”

section.

Feet may not be in contact

with the ﬂoor.

Front and rear feet must be in ﬁrm contact with ﬂoor, and

washer must be level to operate properly.

Washer may not be level. Check ﬂoor for ﬂexing or sagging. If ﬂooring is uneven, a 3/4"

(19 mm) piece of plywood under your washer will reduce sound.

See “Level the Washer” in Installation Instructions.

Load could be unbalanced. Load dry items in loose heaps evenly around basket wall.

Adding wet items to washer or adding more water to basket

could unbalance washer.

Wash smaller loads to reduce imbalance.

Do not tightly pack. Avoid washing single items.

Use Bulky Items cycle for oversized, non-absorbent items such as

comforters or poly-ﬁlled jackets.

See “Cycle Guide” and “Using Your Washer” in this Use and

Care Guide.

Noises

Clicking or metallic noises Objects caught in washer drain system. Empty pockets before washing. Loose items such as coins could fall

between basket and tub or may block pump. It may be necessary to

call for service to remove items.

It is normal to hear metal items on clothing such as metal snaps,

buckles, or zippers touch against the basket.

Gurgling or humming Washer may be draining water. It is normal to hear the pump making a continuous humming sound

with periodic gurgling or surging as ﬁnal amounts of water are

removed during the Drain/Spin cycles.

Humming Load sensing may be occurring. You may hear the hum of the sensing spins after you have started

the washer. This is normal.

Whirring Basket deceleration may be occurring. You may hear the whirring sound of the basket decelerating. This is

normal.

Water Leaks

Check the following

for proper installation:

Washer not level. Water may splash off basket if washer is not level.

Fill hoses not attached tightly. Tighten ﬁll hose connection.

Fill hose washers. Make sure all four ﬁll hose ﬂat washers are properly seated.

Drain hose connection. Pull drain hose from washer cabinet and properly secure it to drain

pipe or laundry tub.

Check household plumbing for leaks

or clogged sink or drain.

Water can back up out of a clogged sink or drain pipe. Check all

household plumbing for leaks (laundry tubs, drain pipe, water pipes,

and faucets).

Washer not loaded as recommended. Unbalanced loading can cause basket to be out of alignment

and cause water to splash off tub. See “Using Your Washer”

for loading instructions.

Washer Not Performing As Expected

Not enough water

in washer

Load not completely covered in water. This is normal operation for a high efﬁciency washer. If the Water

Level knob is set to Auto setting, the load will not be completely

under water. The washer senses load sizes and adds correct

amount of water for optimal cleaning.

Use Bulky Items cycle for higher water ﬁll, or set Water Level knob

to Deep Water Wash setting. See “What’s Under the Lid” and

“Cycle Guide” to match your load with the best cycle.

Run Clean Washer with affresh

cycle to optimize the water level

and wash performance due to soil buildup in washer basket.

First try the solutions suggested here or visit our website at www.maytag.com/owners

(in Canada, www.maytag.ca/owners) for assistance and to possibly avoid a service call.

First try the solutions suggested here or visit our website at www.maytag.com/owners

(in Canada, www.maytag.ca/owners) for assistance and to possibly avoid a service call.

TROUBLESHOOTING

Washer won’t run or ﬁll,

washer stops working,

or wash light remains

on (indicating that the

washer was unable to ﬁll

appropriately) (cont.)

Check proper electrical supply. Plug power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Ensure there is power to outlet.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Normal washer operation. Lid must be closed for washer to run.

Washer will pause during certain phases of cycle. Do not

interrupt cycle.

Washer may be tightly packed. Remove several items, rearrange load evenly in basket. Close lid

and press START/PAUSE/CANCEL.

Do not add more than one or two additional items after cycle

has started to avoid tightly packing or unbalancing.

Do not add more water to the washer.

Washer not draining/

spinning, loads are

still wet, or spin light

remains on (indicating that

the washer was

unable to pump out water

within 10 minutes)

Small items may have been caught

in pump or between basket and tub,

which can slow draining.

Empty pockets and use garment bags for small items.

Use a cycle with a low spin speed. Cycles with lower spin speeds remove less water than cycles

with high spin speeds. Use the recommended cycle/spin speed

for your garment. To remove extra water in the load, select

Drain & Spin. Load may need to be rearranged to allow even

distribution of the load in the basket.

The washer may be tightly packed

or unbalanced.

Tightly packed or unbalanced loads may not allow the washer

to spin correctly, leaving the load wetter than normal. Evenly

arrange the wet load for balanced spinning. Select the Drain &

Spin cycle to remove excess water. See “Using Your Washer”

for loading recommendations.

If you experience Possible Causes Solution

Washer Not Performing As Expected (cont.)

Washer won’t run or ﬁll,

washer stops working,

or wash light remains

on (indicating that the

washer was unable to ﬁll

appropriately)

Check for proper water supply. Both hoses must be attached and have water ﬂowing to

inlet valve.

Both hot and cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water ﬂow.

TROUBLESHOOTING

If you experience Possible causes Solution

Washer Not Performing As Expected (cont.)

Washer not draining/

spinning, loads are

still wet, or spin light

remains on (indicating

that the washer was

unable to pump out water

within 10 minutes) (cont.)

Check plumbing for correct drain hose

installation. Drain hose extends into

standpipe further than 4.5" (114 mm).

Check drain hose for proper installation. Use drain hose form

and securely attach to drain pipe or tub. Do not tape over drain

opening. Lower drain hose if the end is higher than 96" (2.4 m)

above the ﬂoor. Remove any clogs from drain hose.

Too much detergent causing suds to

slow or stop draining and spinning.

Always measure and follow detergent directions for your load.

To remove extra suds, select Rinse & Spin. Do not add detergent.

Dry spots on load

after cycle

High speed spins extract more

moisture than your previous washer.

The high spin speeds combined with air ﬂow during the ﬁnal spin

can cause items near the top of the load to develop dry spots

during the ﬁnal spin. This is normal.

Washer may be tightly packed. Use Bulky Items cycle for higher water ﬁll, or set Water Level knob

to Deep Water Wash setting. See “Cycle Guide” to match your load

with the best cycle.

Added extra garments to the load

after the sensing/ﬁll phase.

Add only one or two additional garments after washer has started.

Incorrect or wrong

wash or rinse

temperatures

Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached to both washer and faucet,

and have both hot and cold water ﬂowing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

Energy saving controlled

wash temperatures.

This washer uses cooler wash and rinse water temperatures

than traditional top-load washers. This includes cooler hot and

warm washes.

Load not rinsed Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached and have water ﬂowing to the

inlet valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.

Not using HE detergent or using too

much HE detergent.

The suds from too much detergent can keep washer from

operating correctly. Always measure detergent and follow

detergent directions based on load size and soil level.

Washer not loaded as recommended. The washer is less efﬁcient at rinsing when load is tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Use cycle designed for the fabrics being washed.

Add only one or two additional garments after washer has started.

Use Bulky Items cycle for higher water ﬁll, or set Water Level knob

to Deep Water Wash setting. See “Cycle Guide” to match your load

with the best cycle.

Sand, pet hair, lint,

etc. on load after

washing

Heavy sand, pet hair, lint, and

detergent or bleach residues may

require additional rinsing.

Add 2 Rinses to the selected cycle and/or use PowerWash cycle or

Deep Water Wash option.

Load is tangling Washer not loaded as recommended. See “Using Your Washer” section.

Select a cycle with a slower wash action and spin speed;

however, items will be wetter than those using a higher speed spin.

Use Bulky Items cycle for higher water ﬁll, or set Water Level knob

to Deep Water Wash setting. See the “Cycle Guide” to match your

load with the best cycle.

Load garments in loose heaps evenly around the basket wall.

Reduce tangling by mixing types of load items. Use the

recommended cycle for the type of garments being washed.

First try the solutions suggested here or visit our website at www.maytag.com/owners

(in Canada www.maytag.ca/owners) for assistance and to possibly avoid a service call.

TROUBLESHOOTING

If you experience Possible Causes Solution

Washer Not Performing As Expected (cont.)

Not cleaning or

removing stains

Added more water to washer. Washer senses load size and adds correct amount of water.

This is normal and necessary for clothes to move. It is normal

for the wash load to be not completely covered in water.

Added water results in less effective cleaning.

Washer not loaded as recommended. Washer is less efﬁcient at cleaning when load is tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Add only one or two additional garments after washer has started.

Adding detergent on top of load. Add detergent, oxi products, and color-safe bleach to the

bottom of the basket before adding the load items.

Not using HE detergent or using too

much HE detergent.

The suds from regular detergent can keep washer from operating

correctly.

Use only HE detergent. Be sure to measure correctly.

Always measure detergent and follow manufacturer’s directions

based on load size and soil level.

Not using correct cycle for fabric type. Use a higher soil level cycle option and warmer wash temp

to improve cleaning.

Use PowerWash cycle for tough cleaning. See the “Cycle Guide”

to match your load with the best cycle.

Not using dispensers. Use dispensers to avoid chlorine bleach and fabric softener staining.

Load dispensers before starting a cycle.

Avoid overﬁlling.

Do not add products directly onto load.

Not washing like colors together. Wash like colors together and remove promptly after the cycle

is complete to avoid dye transfer.

Incorrect dispenser

operation

Clogged dispenser. Load dispensers before starting a cycle.

Use only liquid chlorine bleach in the bleach dispenser. Use only

fabric softener in the fabric softener dispenser.

Rinse Option knob not set for fabric

softener option.

Set Rinse Option knob to 1 Rinse with Fabric Softener or 2 Rinses

with Fabric Softener when using fabric softener dispenser.

Fabric damage Sharp items were in pockets during

wash cycle.

Empty pockets, zip zippers, and snap or hook fasteners before

washing to avoid snags and tears.

Strings and straps could have tangled. Tie all strings and straps before starting wash load.

Items may have been damaged

before washing.

Mend rips and broken threads in seams before washing.

Fabric damage can occur if load is

tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Use cycle designed for the fabrics being washed.

Use Bulky Items cycle for higher water ﬁll, or set Water Level knob

to Deep Water Wash setting. See “What’s Under the Lid” and

“Cycle Guide” to match your load with the best cycle.

Add only one or two additional garments after washer has started.

Liquid chlorine bleach may have been

added incorrectly.

Do not pour liquid chlorine bleach directly onto load. Wipe up

bleach spills.

Undiluted bleach will damage fabrics. Do not use more than

recommended by manufacturer.

Do not place load items on top of bleach dispenser when loading

and unloading washer.

Garment care instructions may not

have been followed.

Always read and follow garment manufacturer’s care label

instructions. See the “Cycle Guide” to match your load with the

best cycle.

First try the solutions suggested here or visit our website at www.maytag.com/owners

(in Canada www.maytag.ca/owners) for assistance and to possibly avoid a service call.

If you experience Possible Causes Solution

Washer Not Performing As Expected (cont.)

Odors Monthly maintenance not done

as recommended.

See “Washer Care” in Washer Maintenance.

Unload washer as soon as cycle is complete.

Using too much detergent. Be sure to measure correctly. Always follow the

manufacturer’s directions.

See “Washer Care” section.

Lid Locked light

is ﬂashing

The lid is not closed. Close the lid. The washer will not start or ﬁll with the lid open.

A cycle was stopped or paused using

the Start/Pause/Cancel button.

The washer may still be spinning. The lid will not unlock until the

basket has stopped spinning. This may take several minutes if

washing large loads or heavy fabrics.

Single-dose laundry packet

not dissolving

Adding laundry packet incorrectly. Be sure laundry packet is added to washer basket before adding

clothes. Do not add packet to dispenser. Follow the manufacturer’s

instructions to avoid damage to your garments.

Washer pumps out water

before ﬁnishing cycle

Lid is left open for more than

10 minutes.

Make sure lid is closed before starting a cycle and/or during

prewash (soak).

First try the solutions suggested here or visit our website at www.maytag.com/owners

(in Canada www.maytag.ca/owners) for assistance and to possibly avoid a service call.

TROUBLESHOOTING

MAYTAG

LAUNDRY

LIMITED WARRANTY

1. Commercial, non-residential, multiple-family use, or use inconsistent

with published user, operator, or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation,

installation not in accordance with electrical or plumbing codes, or

correction of household electrical or plumbing (e.g., house wiring, fuses,

or water inlet hoses).

4. Consumable parts (e.g., light bulbs, batteries, air or water ﬁlters,

preservation solutions).

5. Defects or damage caused by the use of non-genuine Maytag parts

or accessories.

6. Conversion of your product from natural gas or propane gas or reversal

of appliance doors.

7. Damage from accident, misuse, abuse, ﬁre, ﬂoods, acts of God, or use

with products not approved by Maytag.

8. Repairs to parts or systems to correct product damage or defects caused

by unauthorized service, alteration, or modiﬁcation of the appliance.

9. Cosmetic damage including scratches, dents, chips, and other damage

to appliance ﬁnishes unless such damage results from defects in

materials and workmanship and is reported to Maytag within 30 days.

10. Discoloration, rust, or oxidation of surfaces resulting from caustic

or corrosive environments, including but not limited to, high salt

concentrations, high moisture or humidity, or exposure to chemicals.

11. Pick-up or delivery. This product is intended for in-home repair.

12. Travel or transportation expenses for service in remote locations where

an authorized Maytag servicer is not available.

13. Removal or reinstallation of inaccessible appliances or built-in ﬁxtures (e.g.,

trim, decorative panels, ﬂooring, cabinetry, islands, countertops, drywall)

that interfere with servicing, removal, or replacement of the product.

14. Service or parts for appliances with original model/serial numbers

removed, altered, or not easily determined.

The cost of repair or replacement under these excluded

circumstances shall be borne by the customer.

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS

REQUIRED TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

Name, address, and telephone number

Model number and serial number

A clear, detailed description of the problem

Proof of purchase including dealer or retailer name and address

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair. Some questions can be addressed

without service. Please take a few minutes to review the Troubleshooting section of the Use and Care Guide or visit the “HOW-TOS

& FAQS” section of https://www.maytag.com/owners.html.

2. All warranty service is provided exclusively by our authorized Maytag Service Providers.

In the U.S. and Canada, direct all requests for warranty service to:

Maytag Customer eXperience Center

In the U.S.A. call 1-800-344-1274. In Canada call 1-800-688-2002.

If outside the 50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies.

FIRST YEAR LIMITED WARRANTY

(PARTS AND LABOR)

For one year from the date of purchase, when this major

appliance is installed, operated, and maintained according to

instructions attached to or furnished with the product, Maytag

brand of Whirlpool Corporation or Whirlpool Canada LP

(hereafter “Maytag”) will pay for factory specified parts and

repair labor to correct defects in materials or workmanship

that existed when this major appliance was purchased, or

at its sole discretion replace the product. In the event of

product replacement, your appliance will be warranted by the

remaining term of the original unit’s warranty period.

SECOND THROUGH TENTH YEAR LIMITED

WARRANTY (DRIVE MOTOR AND WASH BASKET

ONLY - LABOR NOT INCLUDED)

In the second through tenth years from the date of original

purchase, when this major appliance is installed, operated, and

maintained according to instructions attached to or furnished

with the product, Maytag will pay for factory specified parts for

the following components to correct non-cosmetic defects in

materials or workmanship in these parts that prevent function

of this major appliance and that existed when this major

appliance was purchased. This is a limited 10 year warranty on

the below named parts only and does not include repair labor.

n Drive Motor n Wash Basket (Side Walls Only)

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS

LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS

PROVIDED HEREIN. Service must be provided by a Maytag

designated service company. This limited warranty is valid

only in the United States or Canada and applies only when

the major appliance is used in the country in which it was

purchased. This limited warranty is effective from the date of

original consumer purchase. Proof of original purchase date is

required to obtain service under this limited warranty.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS

FOR A PARTICULAR PURPOSE, ARE LIMITED TO TEN YEARS OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and

provinces do not allow limitations on the duration of implied warranties of merchantability or ﬁtness, so this limitation may not apply to you.

This warranty gives you speciﬁc legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the

exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives

you speciﬁc legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Maytag makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Maytag or your retailer about buying an extended warranty.

10/17

TEN YEAR LIMITED WARRANTY

WHAT IS COVERED

WHAT IS NOT COVERED

SÉCURITÉ DE LA LAVEUSE

CE QUI EST SOUS LE COUVERCLE

Utiliser uniquement un détergent haute efﬁcacité (HE).

IMPORTANT :

■ Le couvercle doit être fermé avant que le panier de la laveuse se remplisse et que le programme de lavage se mette en marche. Si le

couvercle est ouvert, le programme s’arrête et tous les mouvements de remplissage/agitation s’arrêtent. Une fois le couvercle fermé,

le programme reprend automatiquement. Toutefois, si le bouton Start/Pause/Cancel (mise en marche/pause/annulation) est pressé

avant d’ouvrir le couvercle, il faut fermer le couvercle et appuyer de nouveau sur le bouton Start/Pause/Cancel (mise en marche/pause/

annulation) pour reprendre le programme.

■ Rinse Option (option de rinçage) doit être réglée sur 1 Rinse with Fabric Softener (rinçage unique avec assouplissant pour tissu)

ou 2 Rinses with Fabric Softener (double rinçage avec assouplissant pour tissu) lors de l’utilisation d’assouplissant pour tissu dans

le distributeur d’assouplissant pour tissu. Cela garantit que l’assouplissant pour tissu est ajouté au bon moment dans la phase de

rinçage et est uniformément répartie.

Verrouillage du couvercle

Pour permettre des essorages à vitesse plus élevée, le couvercle

se verrouille et le témoin de Lid Locked (couvercle verrouillé)

s’allume. Lorsque ce témoin lumineux s’allume, cela signiﬁe que

le couvercle est verrouillé et ne peut être ouvert sans suspendre

le programme. Lorsque ce témoin lumineux clignote, cela signiﬁe

que la laveuse effectue une pause. Lorsque ce témoin lumineux

est éteint, cela signiﬁe qu’on peut ouvrir le couvercle. Une fois

qu’un programme a commencé, la laveuse se remplit au niveau

d’eau approprié. Sur certains programmes, l’agitation se produit

pendant que le panier se remplit d’eau. Ceci est normal. Quand la

laveuse est faite remplir, l’étape de lavage va commencer. Si l’on

doit ouvrir le couvercle pour ajouter un vêtement après cette étape,

le couvercle de la demeurera déverrouillé pendant toute la partie

de l’agitation de l’étape de lavage. Le programme fait une pause

automatiquement quand le couvercle est ouvert, et le programme

recommencera après la fermeture du couvercle. Le couvercle se

verrouille avant le début de l’étape d’essorage. Si l’on doit pauser

ou arrêter après cette étape, il faut appuyer sur START/PAUSE/

CANCEL (mise en marche/pause/annulation) puis attendre que le

couvercle se déverrouille. Le couvercle se déverrouille uniquement

une fois que le mouvement de la laveuse a cessé. Selon le moment

où l’on souhaite suspendre le programme, le couvercle peut mettre

entre quelques secondes et plusieurs minutes à se déverrouiller.

Appuyer sur START/PAUSE/CANCEL (mise en marche/pause/

annulation) pour poursuivre le programme.

Détection

Cette laveuse détecte automatiquement la taille de la charge

pour la plupart des programmes, et sélectionne un niveau d’eau

approprié en fonction de la taille de la charge détectée. Cette

laveuse effectue également une série d’essorages pour contrôler

l’équilibre de la charge. Durant cette période, une série de cliquetis

et un bruit de frottements rythmiques indiquent que la technologie

de détection détermine si la charge est déséquilibrée.

Options de niveau d’eau

Régler le bouton Water Level (niveau d’eau) sur le réglage

Auto Sensing (détection automatique) et la laveuse ajuste

automatiquement le niveau d’eau en fonction de la taille de la

charge. Régler le bouton Water Level (niveau d’eau) sur le réglage

Deep Water Wash (lavage à l’eau profonde) et la laveuse ajoute

automatiquement plus d’eau à n’importe quel programme à tout

moment pendant le processus de lavage.

Sons normaux prévisibles

Au cours des différents stades du programme de lavage, vous

entendrez peut-être des bruits que votre laveuse précédente

ne produisait pas. Par exemple, vous entendrez peut-être un

cliquetis au début de l’étape d’essorage lorsque le système de

verrouillage du couvercle effectue un test automatique. Différents

bourdonnements et bruits de frottements rythmiques se produiront

à mesure que l’agitateur HE évalue l’équilibre de la charge et qu’il

la déplace. Parfois, il est possible que la laveuse soit complètement

silencieuse, lorsqu’elle détermine le niveau d’eau adéquat ou

qu’elle laisse tremper les vêtements.

Rinçage par vaporisation

Certains programmes utilisent l’option rinçage par vaporisation

par défaut. Au cours de ces programmes, on entend l’eau pénétrer

dans la laveuse tandis que la cuve tourne, ce qui permet à l’eau

de rinçage de pénétrer les vêtements. Consulter le “Guide des

programmes” pour plus de détails.

Choix du détergent approprié

Utiliser uniquement des détergents haute efﬁcacité. L’emballage

portera la mention “HE” ou “High Efﬁciency” (haute efﬁcacité). Il

est probable que l’utilisation d’un détergent non HE prolongera

la durée des programmes et réduira la performance de rinçage.

Ceci peut aussi entraîner des malfunctions de composants et,

avec le temps, une accumulation de moisissure. Les détergents

HE devraient produire peu de mousse et se dissoudre rapidement

pour produire une quantité de mousse idéale pour une performance

optimale. Ils devraient retenir les particules de saleté en suspension

aﬁn qu’elles ne se redéposent pas sur les vêtements propres.

Les détergents identiﬁés HE ne comportent pas tous une formule

identique et ne produisent pas tous la même quantité de mousse.

Par exemple, les détergents HE naturels, organiques et faits maison

peuvent produire une plus grande quantité de mousse. Toujours

suivre les instructions du fabricant pour déterminer la quantité de

détergent à utiliser.

La page charge ...

Maytag MVWC465HW2 Le manuel du propriétaire

Marque: Maytag

Modèle: MVWC465HW2

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MVWC465HW2 Owner's manual

Maytag MVWC465HW2 Le manuel du propriétaire

Ce manuel convient également à

Maytag MVWC465HW2 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents