Maytag MVWB965HC Le manuel du propriétaire

Marque: Maytag

Modèle: MVWB965HC

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Ce manuel convient également à

W11196460A

W11196468A - SP

If you have any problems or questions, visit us at www.maytag.com

Pour tout problème ou question, consulter www.maytag.ca

USE AND CARE GUIDE

GUIDE D’UTILISATION ET D’ENTRETIEN

Top-Loading High Efﬁciency Low-Water Washer

Laveuse haute efﬁcacité à faible consommation

d’eau avec chargement par le dessus

Para obtener acceso

al Manual de uso y

cuidado en español, o para

obtener información adicional

acerca de su producto, visite:

www.maytag.com.

Designed to use only HE High Efciency

detergents.

Conçue pour l’utilisation d’un détergent haute

efcacité seulement.

Table of Contents

WASHER SAFETY .........................................................2

WHAT’S UNDER THE LID ............................................. 4

CONTROL PANEL AND FEATURES ............................5

Dispensers .......................................................................7

CYCLE GUIDE ............................................................... 8

USING YOUR WASHER ..............................................10

WASHER MAINTENANCE .............................................. 14

TROUBLESHOOTING ...................................................... 16

WARRANTY........................................................................ 21

ASSISTANCE OR SERVICE ...........................Back Cover

Table des matières

SÉCURITÉ DE LA LAVEUSE ......................................22

QUOI SOUS LE COUVERCLE ...................................23

TABLEAU DE COMMANDE

ET CARACTÉRISTIQUES ..........................................24

Distributeurs ................................................................. 26

GUIDE DES PROGRAMMES ......................................27

UTILISATION DE LA LAVEUSE ..................................29

ENTRETIEN DE LA LAVEUSE ........................................ 33

DÉPANNAGE ...................................................................... 35

GARANTIE .......................................................................... 42

ASSISTANCE OU SERVICE ..............Couverture arrière

WASHER SAFETY

WHAT’S UNDER THE LID

Choosing the Right Detergent

Use only High Efciency detergents. The package will be

marked “HE” or “High Efciency.” High Efciency wash

systems create excessive sudsing with a regular non-HE

detergent. Using non-HE detergent will likely result in longer

cycle times and reduced rinsing performance. It may also result

in component malfunction and, over time, buildup of mold

or mildew. HE detergents should be low-sudsing and quick-

dispersing to produce the right amount of suds for the best

performance. They should hold soil in suspension so it is not

redeposited onto clean clothes. Not all detergents labeled as

High Efciency are identical in formulation and their ability to

reduce suds. For example, natural, organic, or homemade HE

detergents may generate a high level of suds. Always follow the

detergent manufacturer’s instructions to determine the amount

of detergent to use.

Normal Sounds You Can Expect

At different stages of the wash cycle, you may hear sounds

and noises that are different from those of your previous washer.

For example, you may hear a clicking and hum at the beginning

of the cycle as the lid lock goes through a self-test. There will

be different kinds of humming and whirring sounds as the

agitator moves the load and as the basket is slowing down

to stop. Sometimes, you may hear nothing at all as the washer

determines the correct water level for your load or allows time

for clothes to soak.

Use only High Efciency (HE) detergent.

Automatic Load Size Sensing

Once you start the cycle, the lid will lock, and the washer will

begin the sensing process to determine the correct water level

for the load. This may take several minutes before water is

added. You will nd a step-by-step description in the “Cycle

Status Lights” section.

The basket will start to spin prior to adding water. This is part

of the sensing process and is normal.

For best performance, it is recommended to load items in loose

heaps evenly around the agitator.

As the washer dampens and moves the load, the level of the

items will settle in the basket. This is normal and does not

indicate that more items should be added.

More Water When You Need It

The most striking difference in your new washer is the Dual

Wash Agitator System. In Auto Sensing Water Level mode,

the washer automatically adjusts the water level to the optimal

amount for a High Efciency wash of the detected load size.

In Deep Fill mode, the washer will ll to a pre-determined water

level independent of load size, allowing for greater exibility

in how you wash your clothes.

NOTE: Deep Fill is not available in the Normal cycle mode.

Traditional Low-Water

Wash System

Low-Water Wash System

With Deep Fill Wash Mode

Washplate

Deep Fill

Wash

Low Water

Wash

Dual Wash

Agitator

System

Auto

Sensing

Water

Level

Deep Fill

Washplate

CONTROL PANEL AND FEATURES

POWER BUTTON

Touch to turn the washer On. Touching once while the

washer is on will cancel the current cycle and turn the

washer Off.

WASH CYCLE KNOB

Use the Wash Cycle knob to select cycles on your washer.

See the “Cycle Guide” for detailed descriptions of cycles.

START/PAUSE BUTTON

Touch and hold the START/PAUSE button to begin the

selected cycle; touch again to pause a cycle.

ESTIMATED CYCLE TIME

The Estimated Cycle Time display shows the time required

for the cycle to complete. Factors such as load size and

water pressure may affect the time shown in the display.

Tightly packed loads, unbalanced loads, or excessive suds

may cause the washer to adjust the cycle time, as well.

If you have set a delay start to the cycle, the Estimated

Cycle Time display will show the delay time adjusted.

When the cycle is complete, the display will show END until

the lid is opened.

CYCLE MODIFIERS

When you select a cycle, its default settings or the previous

cycle selection used will light up.

DELAY START

Touch DELAY START to delay the start of the wash

cycle up to 12 hours (“12h”). Touch DELAY START

until “0h” appears in the status display to turn off,

or touch POWER.

TEMPERATURE

Temperature control senses and maintains uniform

water temperatures by regulating incoming hot and

cold water.

Select a wash temperature based on the type of fabric

and soils being washed. For best results and following

the garment label instructions, use the warmest wash

water that is safe for your fabric.

• On some cycles, warm and hot water may be cooler

than your previous washer.

• Even for cold wash settings, some warm water

may be added to the washer to maintain a minimum

temperature.

SOIL LEVEL

Soil Level (wash time) is preset for each wash cycle.

As you touch the Soil Level pad, the cycle time (minutes)

will increase or decrease in the Estimated Time

Remaining display and a different wash time will appear.

Select the most suitable setting for your load. For heavily

soiled items, select Heavy for more wash time. For lightly

soiled items, select Light for less wash time. A lighter soil

level setting will help reduce tangling and wrinkling.

SPIN SPEED

This washer automatically selects the spin speed

based on the cycle selected. The preset speeds can be

changed. Not all spin speeds are available with all cycles.

• Faster spin speeds mean shorter dry times, but may

increase wrinkling in your load.

• Slower spin speeds mean less wrinkling, but will leave

your load more damp.

AUDIO LEVEL

Use this to turn the button sounds and/or signal

indicating the end of a wash cycle to medium, high, or off.

NOTE: You may also turn off the tones that sound when

a feature, setting, or option is touched.

OPTIONS

You may add or remove options for each cycle. Not all

options can be used with all cycles, and some are preset

to work with certain cycles.

MY CYCLE

If you have a cycle with custom settings that you use

frequently, you can use the My Cycle feature to keep

your preferred settings ready to use. To save the cycle,

touch and hold MY CYCLE (approximately 3 seconds)

until a beep sounds and the My Cycle LED is lit. Once

a conguration has been saved, you may power on the

washer and briey touch MY CYCLE to load your saved

cycle and settings.

FABRIC SOFTENER

Select the Fabric Softener option so that the desired

product is added to the load at the correct time.

OXI

Select the Oxi option so that the desired product is added

to the load at the correct time.

Not all features and cycles are available on all models.

NOTE: The control panel features a sensitive surface that responds to a light touch of your nger. To ensure your selections are

registered, touch the control panel with your nger tip, not your ngernail. When selecting a setting or option, simply touch its name

until the desired section is illuminated.

EXTRA RINSE

This option can be used to automatically add a second

rinse to most cycles.

DEEP CLEAN + STEAM

The Deep Clean + Steam option adds additional soak

and wash time to many cycles to help remove tough

stains, as well as a steam boost for added cleaning

power. Deep Clean + Steam uses a heater within the

washer to maintain the selected temperature setting

throughout the wash period. Deep Clean + Steam may

be selected as an option with other cycles.

NOTE: The Deep Clean + Steam option may increase

the selected temperature.

DEEP FILL

If you would like to add the maximum amount of water

to your wash cycle, select the Deep Fill option.

NOTES:

• Expect longer cycle times due to extended fill times

when using the Deep Fill option.

• Deep Fill is not available in the Normal cycle mode.

CYCLE STATUS LIGHTS

The Cycle Status Lights show the progress of a cycle.

At each stage of the process, you may notice sounds

or pauses that are different from traditional washers.

DELAY

When Delay Start has been selected, the Delay light will

illuminate and remain illuminated until the cycle begins.

LID LOCKED

To allow for proper load sensing and spinning, the lid

will lock and the Lid Locked light will turn on. This light

indicates that the lid is locked and cannot be opened.

If you need to open the lid, touch START/PAUSE. The

lid will unlock once the washer movement has stopped.

This may take several minutes if the load was spinning at

a high speed. Touch and hold the START/PAUSE button

again for up to 3 seconds to restart the cycle.

Avoid opening the lid during sensing. The sensing

process will start over when the washer is restarted.

SENSING

When the Start/Pause button is touched and held,

the washer will rst perform a self-test on the lid lock

mechanism. You will hear a click, the basket will make

a slight turn, and the lid will unlock briey before locking

again.

Once the lid has locked the second time, the washer

will use short, slow spins to estimate the load size.

These sensing spins may take 2 to 3 minutes before

water is added to the load and you may hear the hum of

these spins. If the sensing light is on, then the washer is

working properly. You will hear the motor turn the basket

in short pulses to thoroughly wet the load. The washer

will then move the load briey, pause to allow water to

soak into the load, and resume adding water.

This process may repeat until the correct amount of water

has been added for the load. You may also hear water

owing through the dispenser, adding detergent to the

load.

NOTE: Avoid opening the lid during sensing. The sensing

process will start over when the washer is restarted. The

sensing light may also come on during the Wash portion

of the cycle. This is normal.

WASH

You will hear the motor and agitator moving the load.

Unlike traditional washers, the load is not covered with

water. Rather than diluting detergent as done in an

agitator-style washer, this washer delivers the detergent

directly to the soils. The motor sounds may change at

different stages in the cycle. The wash time is determined

by the selected Soil Level.

RINSE

You will hear sounds similar to the wash cycle as the

washer rinses and moves the load.

SPIN

The washer spins the load at increasing speeds for

proper water removal based on the selected cycle

and spin speed.

DONE

Once the cycle is complete, this light will come on.

Remove the load promptly for best results.

Dispensers

Detergent dispenser

Pour measured amount of liquid HE detergent into the

detergent dispenser. The detergent will dispense at the

optimum time during the wash cycle.

NOTE: Do not place single-dose laundry packets or

powder detergent into the dispenser. Add single-dose

laundry packets or powder detergent directly to the

washer basket.

Liquid fabric softener dispenser

Pour measured liquid fabric softener into the liquid fabric

softener dispenser, if desired. It will dispense automatically

at the optimum time.

•

Use only liquid fabric softener in this dispenser.

Use only High Efciency (HE) liquid detergent.

Liquid chlorine bleach and Oxi dispenser

The bleach will be automatically diluted and dispensed at

the optimum time during the wash cycle. This dispenser

cannot dilute powdered bleach.

NOTE: If a gel bleach is used, the Oxi button must be

touched to assist in dispensing the gel.

This dispenser holds up to 3/4 cup (180 mL) Oxi booster

or other laundry booster, such as powdered or liquid

color-safe bleach. Laundry boosters are automatically

dispensed at the proper time during the wash cycle.

Be sure to select Oxi from the options to ensure proper

dispensing.

NOTE: Fill dispenser with only Oxi. Do not mix with bleach.

IMPORTANT: Even on cold cycles, using the Oxi booster

option will cause the washer to use some warm water to

assist in dispensing the Oxi liquid/powder.

CYCLE GUIDE

For best fabric care, choose the cycle that best ts the load being washed. Recommended settings for best performance

are shown in Bold. Not all settings and options are available on each cycle.

Cottons, linens,

and mixed-garment

loads

Normal Hot

Warm

Cold

High Use this cycle for normally soiled cottons and

mixed-fabric loads.

Cleaning

Gentleness

Efciency

†

Good

Best

Heavily soiled

fabrics

Whites Hot

Warm

Cold

High Use this cycle for heavily soiled white fabrics.

Cleaning

Gentleness

Efciency

†

Good

Best

Large items such

as sheets, sleeping

bags, small

comforters

Bedding Hot

Warm

Cold

Low Use this cycle to wash large items such as small comforters.

The washer will ll with enough water to wet down the load

before the wash portion of the cycle begins and uses a

higher water level than other cycles.

Cleaning

Gentleness

Efciency

†

Good

Best

Heavily soiled,

colorfast fabrics

Sanitize w/ Oxi

& Steam*

Hot

Warm

Cold

High Use this cycle to eliminate 99.9% of bacteria when used in

conjunction with the Oxi option. Preset cycle settings must

be used to achieve the proper sanitization. Be sure to add

an Oxi product to the Oxi dispenser.

Cleaning

Gentleness

Efciency

†

Good

Best

Swimsuits and

items requiring

rinsing without

detergent

Rinse &

Spin

Cold Rinse Only High Combines a rinse and spin for loads requiring an additional

rinse cycle or to complete a load after power interruption.

Also use for loads that require rinsing only. To use a spin

only, turn off the Extra Rinse option.

Sturdy fabrics,

colorfast items,

towels, jeans

PowerWash

Hot

Warm

Cold

High Use this cycle for heavily soiled or sturdy items. Water level

sensing process may take longer for some items than for

others because they will absorb more water than other

fabric types.

Cleaning

Gentleness

Efciency

†

Good

Best

No-iron fabrics,

cottons, permanent

press, linens,

synthetics

Wrinkle

Control

Hot

Warm

Cool

Cold

Low Use this cycle to wash loads of no-iron fabrics such as sport

shirts, blouses, casual business clothes, permanent press,

and blends.

Items to wash: Cycle: Wash

Temp:

Spin

Speed:

Cycle Details:

* Extended hot water cycle intended to help sanitize items such as sheets and towels. This cycle is not recommended for all fabrics.

For best results, this cycle should be run to completion to ensure sanitation and should not be interrupted.

†Efficient use of resources, such as energy and water.

Machine-wash silks,

lingerie, washable

wools

Delicates Hot

Warm

Cold

Low Use this cycle to wash lightly soiled items indicating

“Machine Washable Silks” or “Gentle” cycle on the care

label. Place small items in mesh garment bags before

washing.

Cleaning

Gentleness

Efciency

†

Good

Best

Lightly soiled fabrics Rapid Wash Hot

Warm

Cold

High Use this cycle to quickly clean a small number of lightly

soiled items.

Cleaning

Gentleness

Efciency

†

Good

Best

No clothes

in washer

Clean Washer

with affresh

Hot

Warm

Cold

Low Use this cycle every 30 washes to keep the inside of your

washer fresh and clean. This cycle uses a higher water level.

Use with affresh

Washer Cleaner tablet or liquid chlorine

bleach to thoroughly clean the inside of your washer. This

cycle should not be interrupted. See “Washer Care” in the

“Washer Maintenance” section.

IMPORTANT: Do not place garments or other items in the

washer during the Clean Washer with affresh

cycle. Use

this cycle with an empty wash tub.

Items to wash: Cycle: Wash

Temp:

Spin

Speed:

Cycle Details:

†Efficient use of resources, such as energy and water.

USING YOUR WASHER

• Empty pockets. Loose change, buttons, or any small

object can pass under the washplate and become

trapped, causing unexpected sounds.

• Sort items by recommended cycle, water temperature,

and colorfastness.

• Separate heavily soiled items from lightly soiled.

• Separate delicate items from sturdy fabrics.

• Do not dry items if stains remain after washing; heat

can set stains into fabric.

• Treat stains promptly.

• Close zippers, fasten hooks, tie strings and sashes.

Remove non-washable trim and ornaments.

• Mend rips and tears to avoid further damage to items

during washing.

Helpful Tips:

• For best performance, use HE liquid detergent when washing

bulky items.

• When washing waterproof or water-resistant items, load

evenly.

• Use mesh bags to help avoid tangling when washing

delicate or small items.

• Turn knits inside out to avoid pilling. Separate lint-takers

from lint-givers. Synthetics, knits, and corduroy fabrics will

pick up lint from towels, rugs, and chenille fabrics.

• Wash large, absorbent items with other water absorbent items

or alone. Do not mix water absorbent items with items that do

not absorb water as this can cause imbalance.

NOTE: Always read and follow fabric care labels instructions to

avoid damage to your items.

1. Sort and prepare your laundry

Single-dose laundry packets, powder detergent, or fabric

softener crystals can be added to the basket prior to adding

laundry.

NOTE: Always follow manufacturer’s instructions, and never

add single-dose laundry packets, powder detergent, or fabric

softener crystals to the dispensers. They will not dispense

correctly. Add to the basket prior to adding laundry.

2. Add laundry products

For best performance, load items in loose

heaps evenly around the agitator. Try

mixing different sized items to reduce

tangling.

IMPORTANT: Items need to move freely

for best cleaning and to reduce wrinkling and tangling.

3. Load laundry into washer

Liquid Chlorine

Bleach

5. Add liquid chlorine bleach or Oxi

to dispenser (if desired)

Do not overll, dilute, or use more than 1 cup (236 mL) of

liquid cholorine bleach. Pour a measured amount of Oxi-type

boosters, into dispenser; always follow manufacturer’s

directions for correct amount of Oxi-based boosters based

on your load size. Oxi is added during main wash.

IMPORTANT: Do not use color-safe bleach or Oxi products in

the same cycle with liquid chlorine bleach. Oxi option must be

selected to ensure proper distribution at correct time in cycle.

Single Dose

Detergent

Pour a measured amount of HE detergent into dispenser; always

follow manufacturer’s directions for correct amount of detergent

based on your load size.

6. Add liquid fabric softener

to dispenser (if desired)

Pour a measured amount of liquid fabric softener into

dispenser; always follow manufacturer’s directions for

correct amount of fabric softener based on your load size.

Fabric Softener is added during rinse.

IMPORTANT: Do not overll or dilute. Overlling dispenser

will cause fabric softener to immediately dispense into

washer. Do not put fabric softener crystals into dispenser.

If Extra Rinse option is selected, fabric softener will be

dispensed into the last rinse. It is normal for a small amount

of water to remain in the dispenser at the end of a cycle.

7. Touch POWER to turn on washer

Close the lid and touch POWER to turn on the washer.

4. Add HE liquid detergent

Liquid HE

Detergent

Liquid Chlorine

Bleach

Temperature suggestions

Light soils

Colors that

bleed

or fade

Heavy Soils

Whites

Pastels

Moderate

soils

Bright colors

NOTE: Even for cold wash settings, some warm water may

be added to the washer to maintain a minimum temperature.

Turn the cycle knob to choose your

wash cycle. For more information,

see the “Cycle Guide.”

Estimated Time Remaining will

light up with a cycle time. You

may notice time adjusting during

the cycle. This is normal.

If you do not want to begin a cycle immediately, you may

choose Delay Start option.

To choose a delay time:

1. Touch DELAY START button to select desired delay time.

Time will increase in hour increments up to 12 hours.

2. Touch and hold the START/PAUSE button to start delay

start time.

IMPORTANT: When delaying a cycle, use liquid HE detergent

only in the dispenser. Powdered detergents may absorb

moisture from a previous cycle and clump before the wash

cycle begins.

To cancel Delay Start:

1. Touch POWER to cancel Delay Start.

To pause Delay Start:

1. Touch the START/PAUSE button to pause Delay Start.

2. Touch and hold the START/PAUSE button again to start

Delay Start time.

8. Select cycle

9. Select cycle modiers

Once you select a cycle, the default modiers or the previous

set modiers for that cycle will be lit. Touch the cycle settings

buttons to change the Temperature, Soil Level, and Spin Speed,

if desired. Not all settings are available with all cycles.

NOTE: Always read and follow fabric care labels instructions

to avoid damage to your items. If not sure which temperature

to use, refer to the chart below or select a cooler temperature.

11. Touch and hold START/PAUSE

button to begin wash cycle

Touch and hold the START/PAUSE button to start the wash

cycle. When the cycle has nished, the end of cycle signal

will sound (if set). Promptly remove items when cycle is

done to avoid odor, reduce wrinkling, and rusting of metal

hooks, zippers, and snaps.

Unlocking the lid to add items

If you need to open the lid to add one or two missed items:

Touch START/PAUSE button to pause washer; the lid

will unlock once the washer movement has stopped.

This may take several minutes if the load was spinning

at a high speed. Then close the lid and touch and hold

the START/PAUSE button again to restart the cycle.

IMPORTANT: If lid is left open for more than 10 minutes,

the water will pump out and the F8E6 error code will appear

on the display.

Select any other cycle options you may wish to add, if not

previously set. Some cycles will automatically add certain

options such as Extra Rinse. These may be turned off,

if desired.

NOTE: Not all options are available with all cycles. Touch

control panel to select any other options.

10. Select cycle options

WASHER CARE (cont.)

2. Chlorine Bleach Procedure (Alternative):

a. Open the washer lid and remove any clothing

or items.

b. Add 1 cup (236 mL) of liquid chlorine bleach

to the bleach compartment.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause washer damage

over time.

c. Close the washer lid.

d. Do not add any detergent or other chemical

to the washer when following this procedure.

e. Touch POWER to turn on the washer.

f. Select the Clean Washer cycle.

g. Touch and hold the START/PAUSE button to begin

the cycle. The Clean Washer Cycle Operation is

described below.

NOTE: For best results, do not interrupt cycle. If cycle

must be interrupted, touch POWER. After the Clean

Washer cycle has stopped, run a

Rinse & Spin

cycle

to rinse cleaner from washer.

Description of Clean Washer Cycle Operation:

1. This cycle will ll to a water level higher than in normal

wash cycles to provide rinsing at a level above the water

line for normal wash cycle.

2. During this cycle, there will be some agitation and

spinning to increase the removal of soils.

After this cycle is complete, leave the lid open to allow

for better ventilation and drying of the washer interior.

Cleaning the Outside of the Washer

Use an affresh

Machine Cleaning Wipe or a soft, damp cloth

or sponge to wipe away any spills. Use only mild soaps or

cleaners when cleaning external washer surfaces.

IMPORTANT: To avoid damaging the washer’s nish, do not

use abrasive products.

Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Periodically inspect and replace inlet hoses

if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of

replacement on the label with a permanent marker.

NOTE: This washer does not include inlet hoses.

See the Installation Instructions for more information.

WATER INLET HOSES

WASHER CARE

Recommendations to Help Keep Your Washer Clean

and Performing at its Best

1. Always use High Efciency (HE) detergents and follow the

HE detergent manufacturer’s instructions regarding the

amount of HE detergent to use. Never use more than the

recommended amount because that may increase the

rate at which detergent and soil residue accumulate inside

your washer, which in turn may result in undesirable odor.

2. Use warm and hot wash water settings sometimes (not

exclusively cold water washes), because they do a better

job of controlling the rate at which soils and detergent

accumulate.

3. Always leave the washer lid open between uses to

help dry out the washer and prevent the buildup of

odor-causing residue.

Cleaning Your Top Loading Washer

Read these instructions completely before beginning

the routine cleaning processes recommended below.

This Washer Maintenance Procedure should be performed,

at a minimum, once per month or every 30 wash cycles,

whichever occurs sooner, to control the rate at which soils

and detergent may otherwise accumulate in your washer.

Cleaning the Inside of the Washer

To keep your washer odor-free, follow the usage instructions

provided above, and use this recommended monthly

cleaning procedure:

Clean Washer Cycle

This washer has a special cycle that uses higher water

volumes in combination with affresh

Washer Cleaner

or liquid chlorine bleach to clean the inside of the washer.

Begin procedure

1. affresh

Washer Cleaner Cycle Procedure

(Recommended for Best Performance):

a. Open the washer lid and remove any clothing or items.

b. Place an affresh

Washer Cleaner tablet in the bottom

of the washer basket.

c. Do not place an affresh

Washer Cleaner tablet

in the detergent dispenser.

d. Do not add any detergent or other chemical to the

washer when following this procedure.

e. Close the washer lid.

f. Touch POWER to turn on the washer.

g. Select the Clean Washer cycle.

h. Touch and hold the START/PAUSE button to begin

the cycle. The Clean Washer Cycle Operation is

described below.

NOTE: For best results, do not interrupt cycle. If cycle

must be interrupted, touch POWER. After the Clean

Washer cycle has stopped, run a

Rinse & Spin

cycle

to rinse cleaner from washer.

WASHER MAINTENANCE

Operate your washer only when you are home.

If moving, or not using your washer for a period of time,

follow these steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer, to avoid ooding

due to water pressure surge.

NON-USE AND VACATION CARE

WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer

where it will not freeze. Because some water may stay in

hoses, freezing can damage washer. If storing or moving

during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain water

inlet hoses.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run

washer on Rinse & Spin cycle for about 30 seconds

to mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

REINSTALLING/USING WASHER AGAIN

To reinstall washer after non-use, vacation, winter storage

or moving:

1. Refer to Installation Instructions to locate, level, and

connect washer.

2. Before using again, run washer through the following

recommended procedure:

To use washer again:

1. Flush water pipes and hoses. Reconnect water inlet

hoses. Turn on both water faucets.

2. Plug in washer or reconnect power.

3. Run washer through PowerWash

cycle to clean

washer and remove antifreeze, if used. Use only HE

High Efciency detergent. Use half the manufacturer’s

recommended amount for a medium-size load.

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water

inlet hoses.

2. If washer will be moved during freezing weather, follow

“Winter Storage Care” directions before moving.

3. Disconnect drain from drain system.

4. Unplug power cord.

5. Place inlet hoses inside washer basket.

6. Drape power cord and drain hose over the console

and secure with masking tape.

7. Place foam packing ring from original shipping materials

back inside washer. If you do not have packing ring,

place heavy blankets or towels into basket opening.

Close lid and place tape over lid and down front of

washer. Keep lid taped until washer is placed in

new location. Transport washer in the upright position.

TROUBLESHOOTING

If you experience Possible Causes Solution

Vibration or Off-Balance

Vibration, rocking,

or “walking”

Feet may not be in contact with the

oor and locked.

Front and rear feet must be in rm contact with oor, and washer

must be level to operate properly.

Washer may not be level. Check oor for exing or sagging. If ooring is uneven, a 3/4"

(19 mm) piece of plywood under your washer will reduce sound.

See “Level the Washer” in the Installation Instructions.

Vibration during spinning

or washer stopped

Load could be unbalanced.

Load items in loose heaps evenly around the agitator. Adding wet

items to washer or adding more water to basket could unbalance

washer.

Avoid washing single items. Balance a single item such as a rug or

jeans jacket with a few extra items. Redistribute the load, close the

lid, and touch and hold START/PAUSE.

Use Bedding cycle for oversized, non-absorbent items such as

comforters or poly-lled jackets. Other items are not appropriate

for Bedding cycle. See the “Cycle Guide.”

Item or load not suitable for selected cycle. See “Cycle Guide” and

“Using Your Washer.”

Noises – For normal operating sounds, go to www.maytag.com/owners.

Clicking or metallic noises Objects may be caught in washer drain

system.

Empty pockets before washing. Loose items such as coins could fall

between basket and tub or may block pump. It may be necessary to

call for service to remove items.

It is normal to hear metal items on clothing such as metal snaps,

buckles, or zippers touch against the stainless steel basket.

Gurgling or humming Washer may be draining water. It is normal to hear the pump making a continuous humming sound

with periodic gurgling or surging as nal amounts of water are

removed during the spin/drain cycles.

Humming Load sensing may be occurring. You may hear the hum of the sensing spins after you have started

the washer. This is normal.

Whirring Basket may be slowing down. You may hear the whirring sound of the basket slowing down.

This is normal.

Water Leaks

Check the following for

proper installation:

Washer not level. See Installation Instructions for details on how to level your washer.

Fill hoses not attached tightly. Tighten ll-hose connection.

Fill hose washers. Make sure all four ll hose at washers are properly seated.

Drain hose connection. Pull drain hose from washer cabinet and properly secure it to

drainpipe or laundry tub.

Do not place tape over drain opening.

Check household plumbing for leaks

or clogged sink or drain.

Water can back up out of a clogged sink or drainpipe. Check all

household plumbing for leaks (laundry tubs, drain pipe, water pipes,

and faucets.)

Washer not loaded as recommended. An unbalanced load can cause basket to be out of alignment and

cause water to splash off tub. See “Using Your Washer” for loading

instructions.

Washer Not Performing As Expected

Not enough water

in washer

Load not completely covered

in water.

This is normal operation for an HE low-water washer. The load will

not be completely under water. The washer senses load sizes and

adds correct amount of water for optimal cleaning. See “What’s

Under the Lid.”

Use PowerWash

or Bedding cycle for higher water ll, or select the

Deep Fill setting. See “What’s Under the Lid” and the “Cycle Guide”

chart to match your load with the best cycle.

NOTE: Deep Fill is not available in the Normal cycle mode.

Run Clean Washer cycle to optimize the water level and wash

performance.

First try the solutions suggested here or visit our website at www.maytag.com/owners

(in Canada, www.maytag.ca/owners) for assistance and to possibly avoid a service call.

TROUBLESHOOTING

If you experience Possible Causes Solution

Washer Not Performing As Expected (cont.)

Washer won’t run or ll,

washer stops working

Check for proper water supply.

Both hoses must be attached and have water owing to inlet valve.

Both hot and cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water ow.

First try the solutions suggested here or visit our website at www.maytag.com/owners

(in Canada, www.maytag.ca/owners) for assistance and to possibly avoid a service call.

Washer won’t run or ll,

washer stops working

(cont.)

Check proper electrical supply. Plug power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Ensure there is power to outlet.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Normal washer operation. Lid must be closed for washer to run.

Washer will pause during certain phases of cycle. Do not

interrupt cycle.

Washer may be stopped to reduce suds.

Washer may be tightly packed. Remove several items, rearrange load evenly around the agitator.

Close lid, touch and hold START/PAUSE button.

Add only one or two additional items after washer has started.

Do not add more water to the washer.

Not using HE detergent or using

too much HE detergent.

Only use HE detergent (liquid only in the dispenser). Suds from

regular detergents can slow or stop the washer. Always measure

detergent and following detergent directions based on your

load requirements.

To remove suds, cancel cycle. Select Rinse & Spin. Touch and hold

START/PAUSE button. Do not add more detergent.

Washer not draining/

spinning, loads are

still wet

Small items may have been caught

in pump or between basket and tub,

which can slow draining.

Empty pockets and use garment bags for small items.

Using cycles with a lower spin speed. Cycles with lower spin speeds remove less water than cycles

with high spin speeds. Use the recommended cycle/speed spin

for your item.

TROUBLESHOOTING

If you experience Possible Causes Solution

Washer Not Performing As Expected (cont.)

Washer not draining/

spinning, loads are

still wet (cont.)

Washer may be tightly packed or

unbalanced.

Tightly packed loads may not allow the washer to spin correctly,

leaving the load wetter than normal. Evenly arrange the wet load

for balanced spinning. Select Rinse & Spin to remove excess water.

See “Using Your Washer” for loading recommendations.

Load off-balance. See “Vibration or Off-Balance” in Troubleshooting section for more

information.

Check plumbing for correct drain

hose installation. Drain hose extends

into standpipe farther than 4.5"

(114 mm).

Check drain hose for proper installation. Use drain hose

form and securely attach to drainpipe or tub. Do not tape

over drain opening. Lower drain hose if the end is higher than

96" (2.4 m) above the oor. Remove any clogs from drain hose.

Not using HE detergent or using

too much HE detergent.

Suds from regular or too much detergent can slow/stop draining

or spinning. Use only HE detergent. Always measure and follow

directions for your load. To remove extra suds, Select Rinse & Spin.

Incorrect or wrong wash

or rinse temperatures

Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached to both washer and faucet, and have

both hot and cold water owing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

Energy-saving controlled wash

temperatures.

ENERGY STAR

qualied washers use cooler wash and rinse water

temperatures than traditional top-load washers. This includes cooler

hot and warm washes.

Load not rinsed Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached and have water owing to the

inlet valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.

Not using HE detergent or using too

much HE detergent.

The suds from regular detergent can cause the washer to

operate incorrectly.

Use only HE detergent (liquid only in the dispenser). Be sure to

measure correctly.

Always measure detergent and follow detergent directions based on

load size and soil level.

Washer may be tightly packed. The washer is less efcient at rinsing when load is tightly packed.

Load items in loose heaps evenly around the agitator.

Use cycle designed for the fabrics being washed.

Add only one or two additional items after washer has started.

Sand, pet hair, lint, etc.

on load after washing

Heavy sand, pet hair, lint, and

detergent or bleach residues may

require additional rinsing.

Add an Extra Rinse to the selected cycle.

Load is tangling Washer not loaded as recommended. Load items in loose heaps evenly around the agitator.

Reduce tangling by mixing types of load items. Use the

recommended cycle for the type of items being washed.

Wash action and/or spin speed too fast

for load.

Select a cycle with a slower wash action and slower spin speed.

Note that items will be wetter than when using a higher speed spin.

Not cleaning or

removing stains

Added more water to washer. Washer senses load size and adds correct amount of water. This is

normal and necessary for clothes to move. It is normal for the wash

load to be not completely covered in water. Extra water, added

manually, results in less effective cleaning.

Washer not loaded as recommended. Washer is less efcent at cleaning when load is tightly packed.

Load items in loose heaps evenly around the agitator. Load with dry

items only.

Add only one or two additional items after washer has started.

Adding detergent on top of load. Add detergent, Oxi products, and color-safe bleach to the

bottom of the basket before adding the load items.

First try the solutions suggested here or visit our website at www.maytag.com/owners

(in Canada, www.maytag.ca/owners) for assistance and to possibly avoid a service call.

TROUBLESHOOTING

If you experience Possible Causes Solution

Washer Not Performing As Expected (cont.)

Not cleaning or

removing stains (cont.)

Not using HE detergent or using too

much HE detergent.

The suds from regular detergent can prevent washer from operating

correctly.

Use only HE detergent (liquid only in the dispenser). Be sure to

measure correctly.

Always measure detergent and follow detergent directions based

on load size and soil level.

Not using correct cycle for fabric type. Use a higher soil level cycle option and warmer wash temperature

to improve cleaning.

If using Rapid Wash cycle, wash only a few items.

Use PowerWash

cycle for tough cleaning. See the “Cycle Guide”

to match your load with the best cycle.

Not using dispensers. Use dispensers to avoid chlorine bleach and fabric softener staining.

Load dispensers before starting a cycle.

Avoid overlling.

Do not add products directly onto load.

Not washing like colors together. Wash like colors together and remove promptly after the cycle

is complete to avoid dye transfer.

Odors Monthly maintenance not done as

recommended.

Run the Clean Washer cycle after every 30 washes. See “Washer

Care” in “Washer Maintenance.”

Unload washer as soon as cycle is complete.

Not using HE detergent or using too

much HE detergent.

Use only HE detergent (liquid only in the dispenser). Be sure to

measure correctly.

Always follow the detergent directions.

See “Washer Care” section.

Fabric Damage Sharp items were in pockets during

wash cycle.

Empty pockets, zip zippers, and snap or hook fasteners before

washing to avoid snags and tears.

Strings and straps could have tangled. Tie all strings and straps before starting wash load.

Items may have been damaged

before washing.

Mend rips and broken threads in seams before washing.

Fabric damage can occur if the load is

tightly packed.

Load items in loose heaps evenly around the agitator. Load with dry

items only.

Load items should move freely during wash to avoid damage.

Use cycle designed for the fabrics being washed.

Add only one or two additional items after washer has started.

Use PowerWash

or Bedding cycle for higher water ll, or select the

Deep Fill setting. See “What’s Under the Lid” and the “Cycle Guide”

chart to match your load with the best cycle.

NOTE: Deep Fill is not available in the Normal cycle mode.

Garment care instructions may not have

been followed.

Always read and follow garment manufacturer’s care label

instructions. See the “Cycle Guide” to match your load with

the best cycle.

Liquid chlorine bleach may have been

added incorrectly.

Do not pour liquid chlorine bleach directly onto load. Wipe up

bleach spills.

Undiluted bleach will damage fabrics. Do not use more than

recommended by manufacturer.

Do not place load items on top of bleach dispenser when

loading and unloading washer.

Do not use the liquid chlorine bleach and Oxi products at the

same time.

First try the solutions suggested here or visit our website at www.maytag.com/owners

(in Canada, www.maytag.ca/owners) for assistance and to possibly avoid a service call.

TROUBLESHOOTING

If you experience Possible Causes Solution

Washer Not Performing As Expected (cont.)

Incorrect dispenser

operation

Clogged dispensers or laundry

products dispensing too soon.

Do not overll dispenser. Overlling causes immediate dispensing.

Load dispensers before starting a cycle.

It is normal for small amounts of water to be remain in dispenser

at the end of the cycle.

Homes with low water pressure may result in residual powder

in the dispenser. To avoid, select a warmer wash temperature

if possible, depending on your load.

Single-dose laundry

packet not dissolving

Adding laundry packet incorrectly. Be sure laundry packet is added to washer basket before adding

clothes. Follow the manufacturer’s instructions to avoid damage

to your items.

Error Code Appears in Display

“LF” (F8E1) (too long to ll)

appears in display

Washer taking too long to ll. Drain

extends more than 4.5" (114 mm)

into standpipe.

Check plumbing for correct drain hose installation. Use drain hose

form and attach securely to drainpipe or tub. Do not tape over drain

opening. See Installation Instructions.

F#E# code (F-type error

code) appears in display

System error code. Touch POWER to clear the code and exit cycle. Then touch POWER,

select cycle, and then touch and hold START/PAUSE to start washer.

If code appears again, call for service.

F1E1 ACU (Appliance

control fault)

Internal ACU failure. Call for service.

F2E3 UI/ACU mismatch ACU/UI initialization error. Call for service.

F3E1 Water level sensing

failure

Pressure sensor on ACU failure. Call for service.

F5E2 Lid lock will not lock

is lid lock failure

An item in the load may be keeping

the lid from locking.

Check for items directly under the lid.

F5E3 Lid cannot unlock Objects on washer lid prevent it from

unlocking.

Remove objects, such as baskets of laundry, from top of washer.

F6E2 or F6E3

Communication Error:

UI cannot communicate

ACU or UI synchronization error. Remove power from the washer. Let washer set for 5 minutes for

the washer to completely power down. Apply power to washer and

check for error codes. If the error code persists call for service.

F8E6 (Lid opened)

appears in display

Washer lid left open. Close the lid and touch POWER to clear the display. If the lid is left

open for more than 10 minutes, the cycle will reset and water in the

washer will drain.

“drn” “dr” (F9E1) (drain

pump system problem –

long drain) appears in

display

Washer taking too long to drain

water. Drain extends more than

4.5" (114 mm) into standpipe.

Check plumbing for correct drain hose installation. Use drain hose

form and attach securely to drainpipe or tub. Do not tape over drain

opening.

Lower drain hose if the end is higher than 96" (2.4 m) above the oor.

Remove any clogs from drain hose. See Installation Instructions.

“Ofb” (Off Balance) Load not balanced. Open the lid, redistribute the load, close the lid, and touch and hold

START/PAUSE to resume.

First try the solutions suggested here or visit our website at www.maytag.com/owners

(in Canada, www.maytag.ca/owners) for assistance and to possibly avoid a service call.

La page charge ...

Maytag MVWB965HC Le manuel du propriétaire

Marque: Maytag

Modèle: MVWB965HC

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MVWB965HC Owner's manual

Maytag MVWB965HC Le manuel du propriétaire

Ce manuel convient également à

Maytag MVWB965HC Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents