Amana NTW4516FW NTW4516FW Use and Care EN

Marque: Amana

Modèle: NTW4516FW

Catégorie: Machines à laver

Taper: NTW4516FW Use and Care EN

W11099666A

W11099667A-SP

TOP-LOADING WASHER

USE AND CARE GUIDE

Table of Contents

WASHER SAFETY ...................................................................... 2

WHAT’S NEW UNDER THE LID? .............................................. 3

CONTROL PANEL AND FEATURES ......................................... 4

CYCLE GUIDE ............................................................................ 6

USING YOUR WASHER ............................................................. 7

WASHER MAINTENANCE ....................................................... 10

TROUBLESHOOTING .............................................................. 12

WARRANTY .............................................................................. 17

ASSISTANCE OR SERVICE ..................................BACK COVER

Table des matières

SÉCURITÉ DE LA LAVEUSE ................................................... 18

QUOI DE NEUF SOUS LE COUVERCLE? .............................. 19

TABLEAU DE COMMANDE ET CARACTÉRISTIQUES .......... 20

GUIDE DE PROGRAMMES ..................................................... 22

UTILISATION DE LA LAVEUSE ............................................... 23

ENTRETIEN DE LA LAVEUSE ................................................. 26

DÉPANNAGE ............................................................................ 28

GARANTIE ................................................................................ 35

ASSISTANCE OU SERVICE ............... COUVERTURE ARRIÈRE

LAVEUSE À CHARGEMENT PAR LE DESSUS

GUIDE D’UTILISATION ET D’ENTRETIEN

Para una versión de estas instrucciones en español, visite www.amana.com.

Designed to use only HE High Efciency

detergents.

Conçue pour l’utilisation d’un détergent

haute efcacité seulement.

WASHER SAFETY

WHAT’S NEW UNDER THE LID?

Your new washer will operate differently than your past agitator-style washer.

Use only High Efciency (HE) detergent.

Lid Lock

To allow for higher spin speeds, the lid will lock and the Lid

Locked light will turn on. When this light is lit, the lid is locked

and cannot be opened. When this light is blinking, the washer

is paused. When this light is off, the lid can be opened. After

a cycle is started, the washer will ll to the appropriate water

level. When the washer is done lling, it will start to agitate. If

you need to open the lid to add a garment after this point, the

lid will remain unlocked during the entire agitation portion of the

wash phase. The cycle will automatically pause when the lid is

opened, and the cycle will resume once the lid is closed. The lid

will lock before the spin phase begins. If you need to pause or

stop after this point, you must press START/PAUSE/UNLOCK

LID and wait for the lid to unlock. The lid will only unlock after

washer movement has stopped. Depending on when in the

cycle you try to pause, it may take several seconds to several

minutes for the lid to unlock. Press START/PAUSE/UNLOCK

LID to resume the cycle.

Water Level Options

Set the Water Level knob to the Auto Sensing setting and

the washer will ll to a level that ensures the load engages

the agitator. From this point, the electronic control will sense

the load and determine if additional water is needed.

Set the Water Level knob to the Deep Water Wash setting

and the washer will ll to the maximum water level.

NOTE: Deep Water Wash is not available in the Normal cycle

mode. Selecting the Normal cycle with the Deep Water Wash

setting will result in auto sensing of the water level.

Sensing

This washer will perform a series of spins to check for load

balance. During this time, a series of clicks and a whirring

noise signal that sensing technology is determining if there

is an off-balance load.

Normal Sounds You Can Expect

At different stages of the wash cycle, you may hear sounds

and noises that are different from those of your previous washer.

For example, you may hear a clicking and hum at the beginning

of the spin phase as the lid lock goes through a self-test. There

will be different kinds of humming sounds as the agitator tests

for load balance or moves the load. And sometimes, you may

hear nothing at all as the washer determines the correct water

level for your load or allows time for clothes to soak.

Spray Rinse

Select cycles default to a spray rinse. During these cycles,

you will hear water enter the washer as the tub spins, allowing

the rinse water to penetrate clothes. Check the “Cycle Guide”

for details.

Choosing the Right Detergent

Use only High Efciency detergents. The package will be marked

“HE” or “High Efciency.” Using non-HE detergent will likely

result in longer cycle times and reduced rinsing performance. It

may also result in component malfunction and, over time, buildup

of mold or mildew. HE detergents should be low-sudsing and

quick-dispersing to produce the right amount of suds for the

best performance. They should hold soil in suspension so it

is not redeposited onto clean clothes. Not all detergents labeled

as High Efciency are identical in formulation and their ability to

reduce suds. For example, natural, organic, or homemade HE

detergents may generate a high level of suds. Always follow the

detergent manufacturer’s instructions to determine the amount

of detergent to use.

IMPORTANT: The lid must be closed before the washer basket lls with water and for the wash cycle to start. If the lid is open and

lling stops, close the lid and press START/PAUSE/UNLOCK LID to complete the cycle.

Accessories

Enhance your new washer with the following genuine

Whirlpool Accessories. For more information on options

and ordering, call 1-800-901-2042 or visit us at:

www.whirlpool.com/accessories. In Canada, call

1-800-807-6777 or visit us at www.whirlpoolparts.ca.

Fabric Softener Dispenser

This convenient fabric

softener dispenser connects

to the agitator and saves you

from manually adding fabric

softener during the rinse cycle.

CONTROL PANEL AND FEATURES

WATER LEVEL

Set the Water Level knob to the Auto Sensing setting and

the washer will ll to a level that ensures the load engages

the agitator. From this point, the electronic control will sense

the load and determine if additional water is needed.

Set the Water Level knob to the Deep Water Wash setting

and the washer will ll to the maximum water level.

NOTES:

■ Cycle times will be longer due to extended ll times when

using the Deep Water Wash setting.

■ Deep Water Wash is not available in the Normal cycle

mode. Selecting the Normal cycle with the Deep Water

Wash setting will result in auto sensing of the water level.

WASH TEMPERATURE

Wash Temperature senses and maintains uniform water

temperatures by regulating incoming hot and cold water.

Select a wash temperature based on the type of fabric

and soils being washed. For best results and following

the garment label instructions, use the warmest wash

water safe for your fabric.

■ On some models and cycles, warm and hot water may

be cooler than your previous washer.

■ Even in a cold and cool water wash, some warm water

may be added to the washer to maintain a minimum

temperature. All rinses are cold.

WASH CYCLE KNOB

Use the Wash Cycle knob to select cycles on your washer.

See “Cycle Guide” for detailed descriptions of cycles.

START/PAUSE/UNLOCK LID BUTTON

Press to start the selected cycle; press again to pause

the cycle and unlock the lid.

NOTE: If the washer is spinning, it may take several

minutes to unlock the lid. Press and hold for 3 seconds

to cancel a cycle.

Not all features and options are available on all models.

Appearance may vary.

CYCLE STATUS LIGHTS INDICATOR

The Cycle Status lights show the progress of a cycle.

At each stage of the process, you may notice sounds

or pauses that are different from your previous washer.

SENSING/FILL

When the Start/Pause/Unlock Lid button is pressed, and

the Water Level knob is set to Auto Sensing, the washer

will ll and begin sensing to determine load size and

balance.

Once sensing is complete, the washer will ll to the

appropriate level for the detected load size and then

begin the wash phase of the cycle.

NOTE: Sensing and wash phases will be paused by

opening the unlocked lid. Close the lid to resume the

cycle. If the lid is left open for more than 10 minutes,

the washer will cancel the cycle and pump out the water.

The lid will lock after the wash phase to begin the initial

spinout and remain locked for the remainder of the cycle.

WASH

The washer will ll to the correct water level based on

the load size and the Water Level selection. Certain cycles

may agitate during the ll process to boost cleaning. You

will hear the agitator rotate, followed by a pause lasting

several seconds. When the wash cycle begins, you will

hear the agitator increase speed. The motor sounds may

change at different stages in the wash cycle while the

washer performs different wash actions.

RINSE

Certain cycles use a spray rinse, which adds water to

the tub while the basket spins. You may hear the motor

turning on briey (short hum) to move the basket while

lling.

FINAL SPIN

The washer spins the load at increasing speeds for

proper water removal, based on the selected cycle.

CYCLE COMPLETE

Once the cycle is complete, this light will come on.

Remove the load promptly for best results.

LID LOCKED

The Lock feature allows for higher spin

speeds. When the Lid Locked light is

lit, the lid is locked and cannot be

opened without pausing the cycle.

When the light is off, the lid can be

opened.

To open the lid after it has been

locked, press START/PAUSE/UNLOCK

LID. The lid will unlock once the washer

movement has stopped. This may take

several minutes if the load was spinning

at high speed. Press START/PAUSE/

UNLOCK LID again to resume the cycle.

Appearance

may vary.

Appearance

may vary.

CYCLE GUIDE

For best fabric care, choose the cycle that best ts the load being washed. Recommended settings for best performance are shown

in Bold. Each cycle listing also includes a performance chart rating its cleaning power, gentleness on items, and resource efciency.

Not all cycles and options are available on all models. Not all settings and options are available on each cycle.

*All rinses are cold.

†Efcient use of resources, such as energy and water.

Items to wash: Cycle:

Wash

Temperature:* Cycle Details:

Large items such

as sheets, sleeping

bags, small

comforters, jackets,

small washable rugs

Bulky Items

& Sheets

Hot

Warm

Cool

Cold

Tap Cold

Use this cycle to wash large items such as jackets and small

comforters. The washer will ll with enough water to wet down the load

before the wash portion of the cycle begins, and uses a higher water

level than other cycles.

Sturdy fabrics,

colorfast items,

towels, sheets,

jeans

Normal Heavy Hot

Warm

Cool

Cold

Tap Cold

Use this cycle for heavily soiled or sturdy fabrics.

Cleaning

Gentleness

Efciency

†

Good

Best

Cottons, linens,

and mixed garment

loads

Normal

Regular

Hot

Warm

Cool

Cold

Tap Cold

Use this cycle for normally soiled cottons and mixed-fabric loads.

NOTE: Deep Water Wash is not available in the Normal cycle mode.

Selecting the Normal cycle with the Deep Water Wash setting will result

in auto sensing of the water level.

Cleaning

Gentleness

Efciency

†

Good

Best

No-iron fabrics,

cottons, permanent

press, linens,

synthetics

Casual Hot

Warm

Cool

Cold

Tap Cold

Use this cycle to wash loads of no-iron fabrics such as sport shirts,

blouses, casual business clothes, permanent press, and blends.

Cleaning

Gentleness

Efciency

†

Good

Best

Machine-wash silks,

lingerie, washable

wools

Delicate Hot

Warm

Cool

Cold

Tap Cold

Use this cycle to wash lightly soiled garments indicating “Machine

Washable Silks” or “Gentle” cycle on the care label. Place small items

in mesh garment bags before washing.

Cleaning

Gentleness

Efciency

†

Good

Best

Swimsuits and

items requiring

rinsing without

detergent

Rinse &

Spin

Cold rinse only Combines a rinse and high-speed spin for loads requiring an additional

rinse cycle or to complete a load after power interruption. Also use for

loads that require rinsing only.

No clothes in

washer

Clean Washer

with affresh

Hot

Warm

Cool

Cold

Tap Cold

Use this cycle every 30 washes to keep the inside of your washer

fresh and clean. This cycle uses a higher water level. Use with affresh

Washer Cleaner tablet or liquid chlorine bleach to thoroughly clean

the inside of your washer. This cycle should not be interrupted.

See “Washer Care.”

IMPORTANT: Do not place garments or other items in the washer

during the Clean Washer with affresh

cycle. Use this cycle with an

empty washtub.

Hand-washed

garments or

dripping wet items

Drain &

Spin

N/A This cycle uses a spin to shorten drying times for heavy fabrics or

special-care items washed by hand. Use this cycle to drain washer

after cancelling a cycle or completing a cycle after a power failure.

Cleaning

Gentleness

Efciency

†

Good

Best

■ Empty pockets. Loose change, buttons, or any small

object can pass under the agitator and become trapped,

causing unexpected sounds.

■ Sort items by recommended cycle, water temperature,

and colorfastness.

■ Separate heavily soiled items from lightly soiled.

■ Separate delicate items from sturdy fabrics.

■ Do not dry garments if stains remain after washing,

because heat can set stains into fabric.

■ Treat stains promptly.

■ Close zippers, fasten hooks, tie strings and sashes, and

remove non-washable trim and ornaments.

■ Mend rips and tears to avoid further damage to items

during washing.

Helpful Tips:

■ When washing waterproof or water-resistant items,

load evenly.

■ Use mesh garment bags to help avoid tangling when

washing delicate or small items.

■ Turn knits inside-out to avoid pilling. Separate lint-takers

from lint-givers. Synthetics, knits, and corduroy fabrics

will pick up lint from towels, rugs, and chenille fabrics.

NOTE: Always read and follow fabric care label instructions

to avoid damage to your garments.

1. Sort and prepare your laundry

Add a measured amount of HE

detergent or single-dose laundry

packet into the basket.

If using Oxi-type boosters, color-safe

bleach, or fabric softener crystals, add

to the bottom of the washer basket before adding clothes.

IMPORTANT: Use only High Efciency detergents. The

package will be marked “HE” or “High Efciency.” Using

non-HE detergent will likely result in longer cycle times and

reduced rinsing performance. It may also result in component

malfunction and, over time, buildup of mold or mildew. HE

detergents should be low-sudsing and quick-dispersing to

produce the right amount of suds for the best performance.

They should hold soil in suspension so it is not redeposited

onto clean clothes. Not all detergents labeled as High

Efciency are identical in formulation and their ability to

reduce suds. For example, natural, organic, or homemade

HE detergents may generate a high level of suds.

NOTE: Follow the manufacturer’s instructions to determine

the amount of laundry products to use.

2. Add laundry products

USING YOUR WASHER

Liquid

Chlorine Bleach

4. Add liquid chlorine bleach

to dispenser

Do not overll, dilute, or use more than 1 cup (236 mL).

Do not use color-safe bleach or Oxi products in the same

cycle with liquid chlorine bleach.

Load garments in loose heaps evenly

around basket wall. For best results, do

not pack the load tightly. Do not wrap

large items such as sheets around the

agitator; load them in loose piles around

the sides of the basket. Try mixing

different-sized items to reduce tangling.

IMPORTANT: Do not tightly pack or force

items into washer. Items need to move freely for best cleaning

and to reduce wrinkling and tangling.

3. Load laundry into washer

Turn cycle knob to choose your wash cycle. For more

information, see “Cycle Guide.”

5. Select cycle

6. Select WATER LEVEL

Set the Water Level knob to the Auto Sensing setting and

the washer will ll to a level that ensures the load engages

the agitator. From this point, the electronic control will sense

the load and determine if additional water is needed. Select

Extra Rinse for enhanced rinsing performance.

Set the Water Level knob to the Deep Water Wash setting

and the washer will ll to the maximum water level. Select

Extra Rinse for enhanced rinsing performance.

NOTES:

■ Cycle times will be longer due to extended ll times when

using the Deep Water Wash setting.

■ Deep Water Wash is not available in the Normal cycle mode.

Selecting the Normal cycle with the Deep Water Wash

setting will result in auto sensing of the water level.

IMPORTANT: Always select Extra Rinse when manually

adding fabric softener. The Extra Rinse option uses additional

water and agitation for proper fabric softener distribution.

Appearance may vary.

7. Select WASH TEMPERATURE

Select the wash temperature by turning the Wash Temperature

knob to the desired setting. All rinses are tap cold.

NOTE: Always read and follow fabric care label instructions

to avoid damage to your items.

Wash Temp Suggested Fabrics

Hot

Some cold water is added to save

energy. This may be cooler than

your hot water heater setting.

Whites and pastels

Durable items

Heavy soils

Warm

Some cold water may be added,

so this will be cooler than what

your previous washer provided.

Bright colors

Moderate to light soils

Cool

Warm water may be added to

assist in soil removal and to

help dissolve detergents. Cool

is slightly warmer than cold.

Colors that bleed or fade

Light soils

Cold

This is the temperature from your

faucet. If your tap cold water is

very cold, warm water may be

added to assist in soil removal

and help dissolve detergent.

Dark colors that bleed or fade

Light soils

Tap Cold

This is the temperature from your

faucet.

Dark colors that bleed or fade

Light soils

8. Press START/PAUSE/UNLOCK LID

to begin wash cycle

Press START/PAUSE/UNLOCK LID to start the wash cycle.

When the cycle has nished, the Cycle Complete indicator

will light. Promptly remove items after cycle has completed

to avoid odor, reduce wrinkling, and rusting of metal hooks,

zippers, and snaps.

Unlocking the lid to add garments

If you need to open the lid to add one or two missed

garments:

Press START/PAUSE/UNLOCK LID; the lid will unlock once

the washer movement has stopped. This may take several

minutes if the load was spinning at high speed. Then close lid

and press START/PAUSE/UNLOCK LID again to restart the

cycle.

NOTE: Washer will not ll with the lid open.

IMPORTANT: If lid is left open for more than 10 minutes,

the water will pump out automatically.

Manual soak

If you would like to manually soak your garments at any time

during the wash portion of the cycle, press START/PAUSE/

UNLOCK LID and leave the lid closed. Once your desired

soak time has elapsed, press START/PAUSE/UNLOCK LID

again to continue the cycle. As long as the lid remains closed,

your soak time can be longer than 10 minutes. However, if the

lid is opened during the soak and remains open for more than

10 minutes, the water will pump out automatically.

9. Manually add fabric softener

During the nal rinse, wait until the washer has completed

lling, then press START/PAUSE/UNLOCK LID to pause the

washer. Lift the lid and add the measured recommended

amount of liquid fabric softener. Do not use more than the

recommended amount. Close the lid and press START/

PAUSE/UNLOCK LID again to start the washer.

IMPORTANT: Always select Extra Rinse when manually

adding fabric softener. The Extra Rinse option uses

additional water and agitation for proper fabric softener

distribution.

Appearance may vary.

WASHER CARE

Recommendations to Help Keep Your Washer Clean and

Performing at Its Best

1. Always follow the detergent manufacturer’s instructions

regarding the amount of detergent to use. Never use more

than the recommended amount because that may increase

the rate at which detergent and soil residue accumulate

inside your washer which, in turn, may result in undesirable

odor.

2. Use warm and hot wash water settings sometimes (not

exclusively cold water washes) because they do a better

job of controlling the rate at which soils and detergent

accumulate.

3. Always leave the washer lid open between uses to help

dry out the washer and prevent the buildup of odor-causing

residue.

Cleaning Your Top Loading Washer

Read these instructions completely before beginning the

routine cleaning processes recommended below. This Washer

Maintenance Procedure should be performed, at a minimum,

once per month or every 30 wash cycles, whichever occurs

sooner, to control the rate at which soils and detergent may

otherwise accumulate in your washer.

Cleaning the Inside of the Washer

To keep your washer odor-free, follow the usage instructions

provided above and use this recommended monthly cleaning

procedure:

Recommended Cycle for Cleaning the Washer

Refer to the “Cycle Guide” for the optimal cycle for cleaning

the inside of the washer. Use this cycle with affresh

Washer

Cleaner or liquid chlorine bleach as described below.

Begin procedure

1. affresh

Washer Cleaner Cycle Procedure

(Recommended for Best Performance):

a. Open the washer lid and remove any clothing or items.

b. Place an affresh

Washer Cleaner tablet in the bottom

of the washer basket.

c. Do not place an affresh

Washer Cleaner tablet in the

detergent dispenser.

d. Do not add any detergent or other chemical to the

washer when following this procedure.

e. Close the washer lid.

f. Select the cycle recommended for cleaning the inside

of the washer.

g. Press START/PAUSE/UNLOCK LID to start the cycle.

NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, press START/PAUSE/UNLOCK LID once.

After the cycle has stopped, run a Rinse & Spin cycle to rinse

cleaner from washer.

Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Periodically inspect and replace inlet hoses

if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of replacement

on the label with a permanent marker.

NOTE: This washer does not include inlet hoses. See the

Installation Instructions for more information.

WATER INLET HOSES

WASHER MAINTENANCE

Operate your washer only when you are home. If moving or

not using your washer for a period of time, follow these steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer to avoid ooding due

to water pressure surge.

WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer

where it will not freeze. Because some water may stay in

hoses, freezing can damage washer. If storing or moving

during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain water

inlet hoses.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run

washer on Rinse & Spin cycle for about 30 seconds

to mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

NON-USE AND VACATION CARE

WASHER CARE (cont.)

2. Chlorine Bleach Procedure (Alternative):

a. Open the washer lid and remove any clothing or items.

b. Add 1 cup (236 mL) of liquid chlorine bleach to the bleach

compartment.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause washer damage

over time.

c. Close the washer lid.

d. Do not add any detergent or other chemical to the washer

when following this procedure.

e. Select the cycle recommended for cleaning the inside

of the washer.

f. Press START/PAUSE/UNLOCK LID to start the cycle.

NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, press START/PAUSE/UNLOCK LID once.

After the cycle has stopped, run a Rinse & Spin cycle to

rinse cleaner from washer.

Cleaning the Dispensers

After a period of using your washer, you may nd some residue

buildup in the washer’s dispensers. To remove residue from

the dispensers, wipe them with an affresh

Machine Cleaning

Wipe or a damp cloth and towel dry, either before or after you

run the Clean Washer cycle. Do not attempt to remove the

dispensers or trim for cleaning. The dispensers and trim are

not removable. If your model has a dispenser drawer, however,

remove the drawer and clean it before or after you run the

Clean Washer cycle. Use an all-purpose surface cleaner,

if needed.

Cleaning the Outside of the Washer

Use an affresh

Machine Cleaning Wipe or a soft, damp

cloth or sponge to wipe away any spills. Use only an affresh

Machine Cleaning Wipe or mild soaps or cleaners when

cleaning external washer surfaces.

IMPORTANT: To avoid damaging the washer’s nish, do not

use abrasive products.

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water

inlet hoses.

2. If washer will be moved during freezing weather, follow

“Winter Storage Care” directions before moving.

3. Disconnect drain hose from drain system and drain any

remaining water into a pan or bucket. Disconnect drain

hose from back of washer.

4. Unplug power cord.

5. Place inlet hoses and drain hose inside washer basket.

6. Drape power cord over edge and into washer basket.

7. Place packing tray from original shipping materials back

inside washer. If you do not have packing tray, place heavy

blankets or towels into basket opening. Close lid and place

tape over lid and down front of washer. Keep lid taped

until washer is placed in new location. Transport washer

in upright position.

REINSTALLING/USING WASHER AGAIN

To reinstall washer after non-use, vacation, winter storage,

or moving:

1. Refer to the Installation Instructions to locate, level, and

connect washer.

2. Before using again, run washer through the following

recommended procedure:

To use washer again:

1. Flush water pipes and hoses. Reconnect water inlet hoses.

Turn on both water faucets.

2. Plug in washer or reconnect power.

3. Run washer through Bulky Items & Sheets cycle to clean

washer and remove antifreeze, if used. Use only HE

High Efciency detergent. Use 1/2 the manufacturer’s

recommended amount for a medium-size load.

TROUBLESHOOTING

If you experience Possible Causes Solution

Vibration or Off-Balance

Check the following for

proper installation or

see “Using Your

Washer” section.

Feet may not be in contact with the

oor and locked.

Front and rear feet must be in rm contact with oor, and

washer must be level to operate properly.

Washer may not be level. Check oor for exing or sagging. If ooring is uneven, a 3/4"

(19 mm) piece of plywood under your washer will reduce sound.

See “Level the Washer” in Installation Instructions.

Load could be unbalanced. Load dry items in loose heaps evenly around basket wall.

Adding wet items to washer or adding more water to basket

could unbalance washer.

Wash smaller loads to reduce imbalance.

Do not tightly pack. Avoid washing single items.

Use Bulky Items & Sheets cycle for oversized, non-absorbent

items such as jackets and small comforters. See “Cycle Guide.”

See “Cycle Guide” and “Using Your Washer” in this Use and

Care Guide.

Noises

Clicking or metallic

noises

Objects caught in washer drain

system.

Empty pockets before washing. Loose items such as coins

could fall between basket and tub or may block pump.

It may be necessary to call for service to remove items.

It is normal to hear metal items on clothing such as metal snaps,

buckles, or zippers touch against the basket.

Gurgling or humming Washer may be draining water. It is normal to hear the pump making a continuous humming

sound with periodic gurgling or surging as nal amounts of

water are removed during the Drain & Spin cycle.

Humming Load sensing may be occurring. You may hear the hum of the sensing spins after you have

started the washer. This is normal.

Water Leaks

Check the following for

proper installation:

Washer not level. Water may splash off basket if washer is not level. Check that

load is not unbalanced or tightly packed.

Fill hoses not attached tightly. Tighten ll-hose connection.

Fill hose washers. Make sure all four ll hose at washers are properly seated.

Drain hose connection. Pull drain hose from washer cabinet and properly secure it to

drainpipe or laundry tub.

Check household plumbing for leaks

or clogged sink or drain.

Water can back up out of a clogged sink or drainpipe. Check all

household plumbing for leaks (laundry tubs, drain pipe, water

pipes, and faucets).

Washer not loaded as recommended. Improper loading can cause basket to be out of alignment

and cause water to splash off tub. See “Using Your Washer”

for loading instructions.

Washer not performing as expected

Not enough water

in washer

Load not completely covered

in water.

This is normal operation for an HE low-water washer. If the Water

Level knob is set to the Auto Sensing setting, the load will not be

completely under water. The washer senses load sizes and adds

the correct amount of water for optimal cleaning.

IMPORTANT: Do not add more water to washer. Adding water

lifts the items off the washplate, resulting in less effective

cleaning.

Use the Bulky Items & Sheets cycle or set the Water Level knob

to the Deep Water Wash setting. See “What’s New under the

Lid” and “Cycle Guide” to match your load with the best cycle.

NOTE: Deep Water Wash is not available in the Normal cycle

mode. Selecting the Normal cycle with the Deep Water Wash

setting will result in auto sensing of the water level.

Run Clean Washer with affresh

cycle to optimize the water level

and wash performance due to soil buildup in washer basket.

First try the solutions suggested here to possibly avoid a service call.

TROUBLESHOOTING

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Washer won’t run or ll,

washer stops working,

or wash light remains

on (indicating that the

washer was unable

to ll appropriately)

Check for proper water supply. Both hoses must be attached and have water owing to

inlet valve.

Both hot and cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water ow.

First try the solutions suggested here to possibly avoid a service call.

Washer won’t run or ll,

washer stops working,

or wash light remains

on (indicating that the

washer was unable to ll

appropriately) (cont.)

Check proper electrical supply. Plug power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Ensure there is power to outlet.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Normal washer operation. Lid must be closed for washer to run.

Washer will pause during certain phases of cycle. Do not

interrupt cycle.

Washer may be tightly packed. Remove several items, rearrange load evenly in basket. Close lid

and press START/PAUSE/UNLOCK LID.

Do not add more than one or two additional items after cycle has

started to avoid tightly packing or unbalancing.

Do not add more water to the washer.

Washer not draining/

spinning, loads are still

wet, or spin light remains

on (indicating that the

washer was unable to

pump out water within

10 minutes)

Small items may have been caught

in pump or between basket and tub,

which can slow draining.

Empty pockets and use garment bags for small items.

Use a cycle with a low spin speed. Cycles with lower spin speeds remove less water than cycles

with high spin speeds. Use the recommended cycle/spin speed

for your garment. To remove extra water in the load, select

Drain & Spin. Load may need to be rearranged to allow even

distribution of the load in the basket.

The washer may be tightly packed

or unbalanced.

Tightly packed or unbalanced loads may not allow the washer

to spin correctly, leaving the load wetter than normal. Evenly

arrange the wet load for balanced spinning. Select the Drain &

Spin cycle to remove excess water. See “Using Your Washer”

for loading recommendations.

Check plumbing for correct drain

hose installation. Drain hose

extends into standpipe farther

than 4.5" (114 mm).

Check drain hose for proper installation. Use drain hose form

and securely attach to drainpipe or tub. Do not tape over drain

opening. Lower drain hose if the end is higher than 96" (2.4 m)

above the oor. Remove any clogs from drain hose.

Too much detergent causing suds to

slow or stop draining and spinning.

Always measure and follow detergent directions for your load.

To remove extra suds, select Rinse & Spin. Do not add detergent.

TROUBLESHOOTING

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Dry spots on load

after cycle

High spin speeds extract more

moisture than your previous washer.

The high spin speeds combined with airow during the nal

spin can cause items near the top of the load to develop dry

spots during the nal spin. This is normal.

Washer may be tightly packed. Use the Bulky Items & Sheets cycle or set the Water Level knob

to the Deep Water Wash setting. See “Cycle Guide” to match

your load with the best cycle.

NOTE: Deep Water Wash is not available in the Normal cycle

mode. Selecting the Normal cycle with the Deep Water Wash

setting will result in auto sensing of the water level.

Added extra garments to the load

after the sensing/ll phase.

Add only one or two additional garments after washer has

started.

Incorrect or wrong

wash or rinse

temperatures

Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached to both washer and faucet,

and have both hot and cold water owing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

Energy-saving controlled

wash temperatures.

This washer uses cooler wash and rinse water temperatures

than your previous washer. This includes cooler hot and warm

washes.

Load not rinsed Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached and have water owing to the

inlet valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.

Not using HE detergent or using too

much HE detergent.

The suds from too much detergent can keep washer from

operating correctly. Always measure detergent and follow

detergent directions based on load size and soil level.

Washer not loaded as recommended. The washer is less efcient at rinsing when tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Use cycle designed for the fabrics being washed.

Add only one or two additional garments after washer has

started.

Use the Bulky Items & Sheets cycle or set the Water Level knob

to the Deep Water Wash setting. See “Cycle Guide” to match

your load with the best cycle.

NOTE: Deep Water Wash is not available in the Normal cycle

mode. Selecting the Normal cycle with the Deep Water Wash

setting will result in auto sensing of the water level.

Sand, pet hair, lint,

etc., on load after

washing

Heavy sand, pet hair, lint, and

detergent or bleach residues may

require additional rinsing.

Select Rinse & Spin.

Load is tangling Washer not loaded as recommended. See the “Using Your Washer” section.

Select a cycle with a slower wash action and spin speed;

however, items will be wetter than those using a higher speed

spin.

Use the Bulky Items & Sheets cycle or set the Water Level

knob to the Deep Water Wash setting.

See the “Cycle Guide”

to match your load with the best cycle.

NOTE: Deep Water Wash is not available in the Normal cycle

mode. Selecting the Normal cycle with the Deep Water Wash

setting will result in auto sensing of the water level.

Load garments in loose heaps evenly around the basket wall.

Reduce tangling by mixing types of load items. Use the

recommended cycle for the type of garments being washed.

First try the solutions suggested here to possibly avoid a service call.

TROUBLESHOOTING

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Not cleaning or

removing stains

Added more water to washer. Washer senses load size and adds correct amount of water.

This is normal and necessary for clothes to move. It is normal

for the wash load to be not completely covered in water. Added

water lifts the laundry off the washplate, resulting in less effective

cleaning.

Washer not loaded as recommended. Washer is less efcient at cleaning when load is tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Add only one or two additional garments after washer has started.

Adding detergent on top of load. Add detergent, Oxi products, and color-safe bleach to the

bottom of the basket before adding the load items.

Not using HE detergent or using too

much HE detergent.

The suds from regular detergent can keep washer from

operating correctly.

Use only HE detergent. Be sure to measure correctly.

Always measure detergent and follow manufacturer’s directions

based on load size and soil level.

Not using correct cycle for fabric

type.

Use a higher soil level cycle option and warmer wash

temperature to improve cleaning.

Use Heavy cycle for tough cleaning. See the “Cycle Guide”

to match your load with the best cycle.

Not using dispenser.

Use dispenser to avoid chlorine bleach staining.

Load dispenser before starting a cycle.

Avoid overlling.

Do not add chlorine bleach directly onto load.

Not washing like colors together. Wash like colors together and remove promptly after the cycle

is complete to avoid dye transfer.

Not selecting Extra Rinse when using

fabric softener.

Always select Extra Rinse when using fabric softener. Cycles that

have a spray rinse require this option for proper fabric softener

distribution.

Incorrect dispenser

operation

Clogged dispenser. Load dispenser before starting a cycle.

Use only liquid chlorine bleach in the bleach dispenser.

Fabric damage Sharp items were in pockets during

wash cycle.

Empty pockets, zip zippers, and snap or hook fasteners before

washing to avoid snags and tears.

Strings and straps could have tangled.

Tie all strings and straps before starting wash load.

Items may have been damaged

before washing.

Mend rips and broken threads in seams before washing.

Fabric damage can occur if load is

tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Use cycle designed for the fabrics being washed.

Use the Bulky Items & Sheets cycle or set the Water Level knob

to the Deep Water Wash setting. See “What’s New under the

Lid” and “Cycle Guide” to match your load with the best cycle.

NOTE: Deep Water Wash is not available in the Normal cycle

mode. Selecting the Normal cycle with the Deep Water Wash

setting will result in auto sensing of the water level.

Add only one or two additional garments after washer has

started.

Liquid chlorine bleach may have

been added incorrectly.

Do not pour liquid chlorine bleach directly onto load. Wipe up

bleach spills.

Undiluted bleach will damage fabrics. Do not use more than

recommended by manufacturer.

Do not place load items on top of bleach dispenser when

loading and unloading washer.

First try the solutions suggested here to possibly avoid a service call.

TROUBLESHOOTING

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Fabric damage (cont.) Garment care instructions may not

have been followed.

Always read and follow garment manufacturer’s care label

instructions. See the “Cycle Guide” to match your load with

the best cycle.

Odors Monthly maintenance not done as

recommended.

See “Washer Care” in the “Washer Maintenance” section.

Unload washer as soon as cycle is complete.

Using too much detergent. Be sure to measure correctly. Always follow the manufacturer’s

directions.

See the “Washer Care” section.

Lid Locked light is

ashing

The lid is not closed. Close the lid. The washer will not start or ll with the lid open.

A cycle was stopped or paused

using Start/Pause/Unlock Lid.

The washer may still be spinning. The lid will not unlock until

the basket has stopped spinning. This may take several minutes

if washing large loads or heavy fabrics.

Single-dose laundry

packet not dissolving

Adding laundry packet incorrectly. Be sure laundry packet is added to washer basket before

adding clothes. Do not add packet to dispenser. Follow the

manufacturer’s instructions to avoid damage to your garments.

Washer pumps out water

before nishing cycle

Lid is left open for more than

10 minutes.

Make sure lid is closed before starting a cycle and/or during

prewash (soak).

First try the solutions suggested here to possibly avoid a service call.

11/14

AMANA

MAJOR APPLIANCE

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED

TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

■ Name, address and telephone number

■ Model number and serial number

■ A clear, detailed description of the problem

■ Proof of purchase including dealer or retailer name and address

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair. Some

questions can be addressed without service. Please take a few minutes to review the Troubleshooting or

Problem Solver section of the Use and Care Guide, scan the QR code on the right to access additional

resources, or visit http://amana.custhelp.com.

2. All warranty service is provided exclusively by our authorized Amana Service Providers

. In the U.S. and Canada,

direct all requests for warranty service to:

Amana Customer eXperience Center

In the U.S.A., call 1-800-843-0304. In Canada, call 1-800-807-6777.

If outside the 50 United States or Canada, contact your authorized Amana dealer to determine whether another warranty applies.

http://amana.c

usthelp.com

ONE YEAR LIMITED WARRANTY

WHAT IS COVERED WHAT IS NOT COVERED

For one year from the date of purchase, when

this major appliance is installed, operated and

maintained according to instructions attached to

or furnished with the product, Amana brand of

Whirlpool Corporation or Whirlpool Canada LP

(hereafter “Amana”) will pay for Factory Specified

Replacement Parts and repair labor to correct

defects in materials or workmanship that existed

when this major appliance was purchased, or at

its sole discretion replace the product. In the

event of product replacement, your appliance will

be warranted for the remaining term of the

original unit's warranty period.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER

THIS LIMITED WARRANTY SHALL BE

PRODUCT REPAIR AS PROVIDED HEREIN.

Service must be provided by a Amana

designated service company. This limited

warranty is valid only in the United States or

Canada and applies only when the major

appliance is used in the country in which it was

purchased. This limited warranty is effective from

the date of original consumer purchase. Proof of

original purchase date is required to obtain

service under this limited warranty.

1. Commercial, non-residential, multiple-family use, or use inconsistent with published user,

operator or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation, installation not in

accordance with electrical or plumbing codes or correction of household electrical or

plumbing (i.e. house wiring, fuses or water inlet hoses).

4. Consumable parts (i.e. light bulbs, batteries, air or water filters, preservation solutions, etc.).

5. Defects or damage caused by the use of non-genuine Amana parts or accessories.

6. Conversion of products from natural gas or L.P. gas.

7. Damage from accident, misuse, abuse, fire, floods, acts of God or use with products not

approved by Amana.

8. Repairs to parts or systems to correct product damage or defects caused by unauthorized

service, alteration or modification of the appliance.

9. Cosmetic damage including scratches, dents, chips, and other damage to the appliance

finishes unless such damage results from defects in materials and workmanship and is

reported to Amana within 30 days.

10. Discoloration, rust or oxidation of surfaces resulting from caustic or corrosive environments

including but not limited to high salt concentrations, high moisture or humidity or exposure

to chemicals.

11. Food or medicine loss due to product failure.

12. Pick-up or delivery. This product is intended for in-home repair.

13. Travel or transportation expenses for service in remote locations where an authorized

Amana servicer is not available.

14. Removal or reinstallation of inaccessible appliances or built-in fixtures (i.e. trim, decorative

panels, flooring, cabinetry, islands, countertops, drywall, etc.) that interfere with servicing,

removal or replacement of the product.

15. Service or parts for appliances with original model/serial numbers removed, altered or not

easily determined.

The cost of repair or replacement under these excluded circumstances shall be borne by

the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow

limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you

specific legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Amana makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations

contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance,

you should ask Amana or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. AMANA

SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation

of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and

you also may have other rights that vary from state to state or province to province.

SÉCURITÉ DE LA LAVEUSE

QUOI DE NEUF SOUS LE COUVERCLE?

Votre nouvelle laveuse fonctionne différemment de votre précédente laveuse de type agitateur.

Utiliser uniquement un détergent haute efcacité (HE).

Verrouillage du couvercle

Pour permettre des essorages à vitesse plus élevée, le

couvercle se verrouille et le témoin de couvercle verrouillé

s’allume. Lorsque ce témoin lumineux s’allume, cela signie

que le couvercle est verrouillé et ne peut être ouvert. Lorsque

ce témoin lumineux clignote, cela signie que la laveuse

effectue une pause. Lorsque ce témoin lumineux est éteint,

cela signie qu’on peut ouvrir le couvercle. Une fois qu’un

programme a commencé, la laveuse se remplit au niveau

d’eau approprié. Quand la laveuse est faite remplir, l’agitation

va commencer. Si l’on doit ouvrir le couvercle pour ajouter

un vêtement après cette étape, le couvercle de la demeurera

déverrouillé pendant toute la partie de l’agitation de l’étape de

lavage. Le programme fait une pause automatiquement quand

le couvercle est ouvert, et le programme recommencera après

la fermeture du couvercle. Le couvercle se verrouille avant

le début de l’étape d’essorage. Si l’on doit pauser ou arrêter

après cette étape, il faut appuyer sur START/PAUSE/UNLOCK

LID (mise en marche/pause/déverrouillage du couvercle)

puis attendre que le couvercle se déverrouille. Le couvercle

se déverrouille uniquement une fois que le mouvement de la

laveuse a cessé. Selon le moment où l’on souhaite suspendre

le programme, le couvercle peut mettre entre quelques

secondes et plusieurs minutes à se déverrouiller. Appuyer

sur START/PAUSE/UNLOCK LID (mise en marche/pause/

déverrouillage du couvercle) pour poursuivre le programme.

Options de niveau d’eau

Régler le bouton de niveau d’eau sur Auto Sensing (détection

automatique) pour que la laveuse se remplisse d’eau à

un niveau qui assure que la charge déclenche l’agitateur.

À ce stade, la commande électronique détecte la charge

et détermine si de l’eau supplémentaire est nécessaire.

Régler le bouton Water Level (niveau d’eau) sur le réglage

Deep Water Wash (lavage à niveau d’eau élevé) et la laveuse

se remplit jusqu’au niveau d’eau maximal.

REMARQUE : L’option Deep Water Wash (lavage à niveau

d’eau élevé) n’est pas disponible avec le programme Normal

(normal). Un programme Normal (normal) avec option Deep

Water Wash (lavage à niveau d’eau élevé) utilisera la détection

automatique du niveau de l’eau.

Détection

Cette laveuse effectue une série d’essorages pour contrôler

l’équilibre de la charge. Durant cette période, une série de

cliquetis et un bruit de frottements rythmiques indiquent

que la technologie de détection détermine si la charge

est déséquilibrée.

Sons normaux prévisibles

Au cours des différents stades du programme de lavage, vous

entendrez peut-être des bruits que votre laveuse précédente

ne produisait pas. Par exemple, vous entendrez peut-être un

cliquetis et un bourdonnement au début de l’étape d’essorage

lorsque le système de verrouillage du couvercle effectue un

test automatique. Différents bourdonnements et bruits de

frottements rythmiques se produiront à mesure que l’agitateur

évalue l’équilibre de la charge et qu’il la déplace. Parfois, il

est possible que la laveuse soit complètement silencieuse,

lorsqu’elle détermine le niveau d’eau adéquat ou qu’elle laisse

tremper les vêtements.

Rinçage par vaporisation

Certains programmes utilisent l’option rinçage par vaporisation

par défaut. Au cours de ces programmes, on entend l’eau

pénétrer dans la laveuse tandis que la cuve tourne, ce qui

permet à l’eau de rinçage de pénétrer les vêtements. Consulter

le “Guide de programmes” pour plus de détails.

Choix du détergent approprié

Utiliser uniquement des détergents haute efcacité. L’emballage

portera la mention “HE” ou “High Efciency” (haute efcacité). Il

est probable que l’utilisation d’un détergent non HE prolongera

la durée des programmes et réduira la performance de rinçage.

Ceci peut aussi entraîner des malfunctions de composants et,

avec le temps, une accumulation de moisissure. Les détergents

HE devraient produire peu de mousse et se dissoudre

rapidement pour produire une quantité de mousse idéale pour

une performance optimale. Ils devraient retenir les particules de

saleté en suspension an qu’elles ne se redéposent pas sur les

vêtements propres. Les détergents identiés HE ne comportent

pas tous une formule identique et ne produisent pas tous la

même quantité de mousse. Par exemple, les détergents HE

naturels, organiques et faits maison peuvent produire une plus

grande quantité de mousse. Toujours suivre les instructions

du fabricant pour déterminer la quantité de détergent à utiliser.

IMPORTANT : Le couvercle doit être fermé avant que le panier de la laveuse se remplisse et que le programme de lavage se mette

en marche. Si le couvercle est ouvert et que le remplissage s’arrête, fermer le couvercle et appuyer sur START/PAUSE/UNLOCK LID

(mise en marche/pause/déverrouillage du couvercle) pour terminer le programme.

Accessoires

Améliorer votre nouvelle laveuse grâce aux authentiques

accessoires Whirlpool suivants. Pour plus d’informations sur

les options et pour commander, composer le 1-800-901-2042,

ou visiter notre site Web à : www.whirlpool.com/accessories.

Au Canada, composer le 1-800-807-6777 ou visiter notre site

Web à www.whirlpoolparts.ca.

Distributeur d’assouplissant

pour tissu

Ce distributeur d’assouplissant

pour tissu pratique est relié

à l’agitateur et vous évite

d’ajouter manuellement

l’assouplissant pour tissu

durant le programme

de rinçage.

TABLEAU DE COMMANDE ET CARACTÉRISTIQUES

WATER LEVEL (niveau d’eau)

Régler le bouton de niveau d’eau sur Auto Sensing

(détection automatique) pour que la laveuse se remplisse

d’eau à un niveau qui assure que la charge déclenche

l’agitateur. À ce stade, la commande électronique détecte

la charge et détermine si de l’eau supplémentaire est

nécessaire.

Régler le bouton Water Level (niveau d’eau) sur le réglage

Deep Water Wash (lavage à niveau d’eau élevé) et la laveuse

se remplit jusqu’au niveau d’eau maximal.

REMARQUES :

■ La durée du programme sera plus grande

en raison du temps de remplissage plus long que

demande le réglage Deep Water Wash (lavage à niveau

d’eau élevé).

■ L’option Deep Water Wash (lavage à niveau d’eau élevé)

est disponible avec le programme Normal (normal).

Un programme Normal (normal) avec option Deep Water

Wash (lavage à niveau d’eau élevé) utilisera la détection

automatique du niveau de l’eau.

WASH TEMPERATURE (température de lavage)

La fonction Wash Temperature (température de lavage)

détecte et maintient une température uniforme de l’eau

en régulant le débit d’arrivée d’eau chaude et d’eau froide.

Sélectionner une température de lavage en fonction du type

de tissu et de saleté à laver. Pour des résultats optimaux,

suivre les instructions sur l’étiquette du vêtement et utiliser

la température d’eau de lavage la plus chaude possible qui

reste sans danger pour le tissu.

■ Sur certains modèles et pour certains programmes, les

températures utilisées pour l’eau chaude et l’eau tiède

peuvent être inférieures aux températures utilisées par

votre précédente laveuse.

■ Même pour les lavages dont la température a été réglée

sur Cool (frais) ou Cold (froid), il est possible que de

l’eau tiède soit ajoutée à la laveuse pour maintenir

une température minimale. Tous les rinçages se font

à l’eau froide.

Certains programms et options ne sont pas disponibles sur certains modèles.

L’apparence des appareils peut varier.

BOUTON DE PROGRAMME DE LAVAGE

Utiliser le bouton du programme de lavage pour sélectionner

les programmes disponibles sur la laveuse. Voir “Guide

de programmes” pour des descriptions de programmes

détaillées.

BOUTON START/PAUSE/UNLOCK LID

(mise en marche/pause/déverrouillage

du couvercle

)

Appuyer sur ce bouton pour démarrer le programme

sélectionné, puis appuyer de nouveau pour suspendre

le programme et déverrouiller le couvercle.

REMARQUE : Si la laveuse tourne, le couvercle peut

mettre quelques minutes à se déverrouiller. Appuyer

pendant 3 secondes pour annuler un programme.

CYCLE STATUS LIGHTS INDICATOR

(TÉMOINS LUMINEUX DES PROGRAMMES)

Les témoins lumineux indiquent la progression du

programme. À chaque étape du processus, il est possible

que l’on remarque des pauses ou des sons que la

précédente ne produisait pas.

SENSING/FILL (détection/remplissage)

Lorsqu’on appuie sur Start/Pause/Unlock Lid

(mise en marche/pause/déverrouillage du couvercle),

et que le bouton Water Level (niveau d’eau) est réglé

sur Auto Sensing (détection automatique), la laveuse

se remplit et lance la détection pour déterminer la taille

et l’équilibre de la charge.

Une fois la détection terminée, la laveuse se remplit

jusqu’au niveau d’eau approprié en fonction de la taille

de la charge détectée et commence l’étape de lavage

du programme.

La page charge ...

Amana NTW4516FW NTW4516FW Use and Care EN

Marque: Amana

Modèle: NTW4516FW

Catégorie: Machines à laver

Taper: NTW4516FW Use and Care EN

Télécharger le PDF

rapport

dans d''autres langues

English: Amana NTW4516FW

Amana NTW4516FW NTW4516FW Use and Care EN

Amana NTW4516FW NTW4516FW Use and Care EN

dans d''autres langues

Documents connexes

Autres documents