Whirlpool WRS321SDHW Guide d'installation

Marque: Whirlpool

Modèle: WRS321SDHW

Catégorie: Frigos

Taper: Guide d'installation

W11366704A

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

Side by Side Refrigerator

Do Not Throw Away - Additional important safety information included.

Para las instrucciones en español, visite nuestro sitio de internet.

TABLE OF CONTENTS / TABLE DES MATIÈRES

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL ..............................................................1

REFRIGERATOR SAFETY .............................................................. 2

INSTALLATION INSTRUCTIONS ...................................................3

Unpack the Refrigerator ............................................................... 3

Door Removal, Leveling, and Alignment .....................................4

Handle Installation and Removal .................................................6

Location Requirements ................................................................7

Electrical Requirements ...............................................................7

Water Supply Requirements ........................................................7

Connect Water Supply .................................................................8

REFRIGERATOR CARE ...............................................................10

Cleaning .....................................................................................10

Lights ..........................................................................................11

Vacation and Moving Care .........................................................11

TROUBLESHOOTING ..................................................................12

PERFORMANCE DATA SHEET ...................................................17

Notes ..........................................................................................34

INSTRUCTIONS D’INSTALLATION

ET MANUEL DU PROPRIÉTAIRE .................................................1

SÉCURITÉ DU RÉFRIGÉRATEUR...............................................18

INSTRUCTIONS D’INSTALLATION .............................................19

Déballage du réfrigérateur..........................................................19

Retrait, mise au niveau et alignement des portes .....................20

Installation et retrait des poignées .............................................22

Exigences d’emplacement .........................................................23

Spécications électriques ..........................................................23

Spécications de l’alimentation en eau .....................................24

Raccordement à la canalisation d’eau ......................................24

ENTRETIEN DU RÉFRIGÉRATEUR ............................................27

Nettoyage ...................................................................................27

Lampes .......................................................................................27

Précautions à prendre pour lesvacances ou

le déménagement ......................................................................28

Tablette de congeateur (le nombre de tablettes varie selon le

modèle) .......................................................................................28

DÉPANNAGE ................................................................................. 29

FEUILLES DE DONNÉES SUR LA PERFORMANCE ................34

INSTRUCTIONS D’INSTALLATION

ETMANUELDUPROPRIÉTAIRE

Réfrigérateur côte à côte

Ne pas jeter – Autres consignes de sécurité importantes ci-jointes.

Para las instrucciones en español, visite nuestro sitio de internet.

REFRIGERATOR SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

WARNING:

IMPORTANT SAFETY INSTRUCTIONS

PLEASE KEEP THESE INSTRUCTIONS

 Plug into a grounded 3-prong outlet.

 Do not remove the ground prong.

 Do not use an adapter.

 Do not use an extension cord.

 Disconnect power before servicing.

 Replace all parts and panels before operating.

 Remove doors from your old refrigerator.

 Connect only to the potable water supply.

 Use non-flammable cleaner.

 Keep flammable materials and vapors, such as gasoline, well

away from the refrigerator.

 Use two or more people to move and install the refrigerator.

 Disconnect the power before installing the ice maker (on ice

maker kit-ready models only).

 Use a sturdy glass when dispensing ice (on some models).

 Do not hit the refrigerator glass doors (on some models).

 This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

 Children should be supervised to ensure that they do not

play with the appliance.

 If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified

person in order to avoid a hazard.

 Do not store explosive substances such as aerosol cans

with a flammable propellant in this appliance.

 This appliance is intended to be used in household and

similar applications such as:

- Staff kitchen areas in shops, offices and other working

environments;

- Farm houses and by clients in hotels, motels and other

residential type environments;

- Bed and breakfast type environments;

- Catering and similar non-retail applications.

To reduce the risk of fire, electric shock or injury to persons when using the refrigerator,

follow basic precautions, including the following:

Proper Disposal of

Your Old Refrigerator

IMPORTANT: Child entrapment and suffocation are not

problems of the past. Junked or abandoned refrigerators are still

dangerous, even if they will sit for “just a few days.” If you are

getting rid of your old refrigerator, please follow these instructions

to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

Remove packing materials. Do not use sharp instruments,

rubbing alcohol, ammable uids, or abrasive cleaners to remove

tape or glue. These products can damage the surface of your

refrigerator. For more information, see “Refrigerator Safety.”

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the oor with

cardboard or hardboard to avoid oor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

“walk” the refrigerator when trying to move it, as oor

damage could occur.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Door Removal, Leveling, and Alignment

Gather the required tools and parts and read all instructions before starting installation. Save these instructions for future reference.

NOTE: Before moving your product into your home, measure the doorway of your home to see whether you need to remove the

refrigerator and freezer doors. If door removal is necessary, see the instructions below.

IMPORTANT: Before you begin, unplug refrigerator or disconnect power. Remove food, the ice storage bin (on some models), and any

adjustable door or utility bins from doors.

TOOLS NEEDED: Bubble level; at-blade screwdriver; 5/16" and 11/16" wrench; 1/4", 3/8", and 5/16" hex-head socket wrenches,

Phillips screwdriver tip #2 with 4" long as minimum, TORX T30

†

screwdriver.

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

A CB

Top Left Hinge

Door Removal

Top Right Hinge

Left and Right Bottom Hinge

Wiring

Water Dispenser

Tubing

Full Refrigerator

Base Grille

Water Filter Door and Base Grille

Alignment Screw

Locking Nut

Leveling screws

Do not remove A screws

Do not remove B screws

A. Wiring plugs

B. Wiring clip

C. Grommets

A. Face of tting

A. Pull to the right for extraction

B. Twist and pass underneath door

Pull toward you.

Phillips screws

Lower

Raise

5/16"

wrench

Loosen

Tighten

11/16"

wrench

Raise

Lower

Raise

Cabinet

Freezer

door

Adjustable front wheels

Water

lter door

Base

grille

Refrigerator

door

†

TORX and T30 are trademarks of Acument Intellectual Properties, LLC.

Remove the Doors

If your refrigerator does not t through the doorway or you are

getting rid of your old refrigerator, follow the steps below for door

removal.

1. Unplug refrigerator or disconnect power.

2. Fully open both doors. See graphic 1.

3. If your model has water dispensing, please open the water

lter door by pulling it toward you. See graphic 2. It is not

necessary to remove the water lter itself.

4. Pull the base grille toward you from the sides and then from

the center until it dislodges. See graphic 2.

5. To remove the base grille, twist and pull the right side until this

side passes underneath the refrigerator door. See graphic 3.

Then pull the left side of the base grille for complete removal.

6. If your model has water dispensing in the door, disconnect the

water dispenser tubing located below the freezer door.

■ Press the blue outer ring against the face of tting and pull

the dispenser tubing free. See graphic 4.

NOTE: Keep the water tubing connector attached to the tube

that runs underneath the freezer. The door cannot be removed

if the connector is still attached to the tube that runs through

the door hinge.

7. If your model has water dispensing in the door, disconnect the

wiring located below the freezer door. See graphic 5.

■ Remove the wiring clip and the bracket wire using a 1/4"

hexagonal head socket wrench.

■ Disconnect the wiring plugs from the bracket wire.

8. Close the freezer door and use a TORX T30 screwdriver to

remove the top hinge completely. See graphic 6.

IMPORTANT: Do not remove either screw A. Hold the door

while hinge is being removed.

9. Lift the freezer door straight up off from the bottom hinge. See

graphic 7. The water dispenser tubing and wiring will remain

attached to the freezer door.

NOTE: This may require two people, one to lift the door and

another to feed the water tubing and wiring into the bottom

hinge pin.

IMPORTANT: Rest the door on its side on a soft, clean

surface, such as a towel, blanket, or piece of cardboard. This

will help to avoid scratching or damaging the door, water

tubing, and wiring.

10. Close the refrigerator door and use a TORX T30 screwdriver

to remove completely top hinge. See graphic 8.

IMPORTANT: Do not remove either screw A. Hold the door

while hinge is being removed.

11. Lift the refrigerator door straight up off from the bottom hinge.

See graphic 7.

IMPORTANT: Rest the door on its side on a soft, clean

surface, such as a towel, blanket, or piece of cardboard.

This will help to avoid scratching or damaging the door

12. If your refrigerator without doors does not pass through the

doorway, you may remove both bottom hinges. Use a 5/16"

nut driver to remove these. See graphic 9.

IMPORTANT: Do not remove either screw B.

Replacing or Reinstalling Door and Hinges

If your doors and bottom hinges have been removed, please

follow the next instructions for re-installation:

1. Reinstall both bottom hinges using a 5/16" nut driver to

tighten screws. See graphic 9.

2. If your model has water dispensing in the door:

■ Lift the freezer door enough to feed the water dispenser

tubing and wiring through the bottom hinge pin.

NOTE: This may require two people, one to lift the door and

the other to feed the water tubing and wiring into the bottom

hinge pin. See graphic 7.

■ Insert the freezer door into the bottom hinge pin.

IMPORTANT: Hold the door while hinge is being installed

3. Close the freezer door to align and reinstall the top hinge.

Use a TORX T30 screwdriver to tighten the screws. See

graphic 8.

IMPORTANT: Provide additional support for the door while

top hinge is being reinstalled. Do not depend on the door

magnets to assure the door to the cabinet.

4. If your model has water dispensing in the door, connect the

water dispenser tubing. For the connection, push the tubing

into the dispenser tubing until black mark touches the face of

tting. See graphic 4.

5. Connect the wiring. See graphic 5.

6. Reinstall the wiring clip & the bracket wire using a 1/4"

hexagonal head socket wrench.

7. Connect the wiring plugs from the bracket wire.

8. Lift the refrigerator door enough to insert the door into the

bottom hinge pin. See graphic 7.

IMPORTANT: Hold the door while hinge is being installed.

9. Close the refrigerator door to align and reinstall the top hinge.

Use a TORX T30 screwdriver to tighten the screws. See

graphic 6.

IMPORTANT: Provide additional support for the door while

top hinge is being reinstalled. Do not depend on the door

magnets to assure the door to the cabinet.

Leveling and Door Closing

Your refrigerator has two front adjustable wheels. See graphic 1.

These are used to level the refrigerator under uneven oor

conditions or want the doors to close more easily. Please follow

the instructions below:

1. Use a Bubble level to check levelness of oor where the

rear side of the refrigerator will rest. If the refrigerator is not

leveled, adjust or add the shim on ooring to create a leveled

oor for the rear side wheels. A leveled rear side prevents the

refrigerator cabinet from forming a twist.

2. Place the refrigerator into its nal location in the kitchen and

open both doors.

3. Fully open both doors. See graphic 1.

4. If your model has water dispensing in the door, please open

the water lter door by pulling it toward you. See graphic 2. It

is not necessary to remove the water lter itself.

5. Pull the base grille toward you from the sides and then from

the center until it dislodges. See graphic 2.

6. To remove the base grille, twist and pull the right side until this

side passes underneath the refrigerator door. See graphic 3.

Then pull the left side of the base grille for complete removal.

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

7. Raise the wheels while one person pushes on the refrigerator

to lift from front side. Use the bubble level on top of the

refrigerator or on its side to level the refrigerator. Check

bubble level and at the same time observe the gaps and

squareness to the adjacent cabinets, furniture or trim. If

adjacent furnishings are not level, it may not be possible to

achieve even gaps when product is level. Continue adjusting

until all four corners are steady without rock.

8. Use a 3/8" nut driver to turn the leveling screws located in

both sides of the refrigerator. See graphic 10. Depending on

uneven oor conditions, you must turn one or both screws to

the right or left several times to raise or lower the refrigerator.

9. Close both doors and check that they close as easily as

you like. If not, turn both screws to the right to raise the

refrigerator by tiling it more to the back until the doors close

as easily as you like.

10. Check and make sure to the technician sheet is placed in the

base grille cavity before assembling this into the cabinet.

11. Reinstall the base grille into the cabinet, introducing the left

side rst and then the right side of the base grille. See graphic

3. You may accommodate the water dispenser tubing and

wiring into base grille cavity below the left bottom hinge.

12. Attach the base grille pushing into the cabinet clips. See

graphic 2.

Door Alignment

The refrigerator doors are designed to be slightly misaligned

vertically when the refrigerator is empty. Please follow the next

steps to align the refrigerator doors.

1. Use an 11/16" open-ended wrench tool to loosen the locking

nut located below the refrigerator door. See graphic 11.

Accommodate the wrench tool so that it ts in the space.

2. Use a 5/16" open-ended wrench tool to turn the alignment

screw. See picture 12. Depending on how the refrigerator door

is misaligned in relation to the freezer door, you must turn the

screw to the right to raise or to the left to lower the refrigerator

door until both doors have been aligned vertically.

3. Tighten the 11/16" locking nut with the wrench tool.

4. Attach the base grille if it was dislodged.

Handle Installation and Removal

PARTS INCLUDED: Door handles (2), 1/8" hex key, spare

setscrew(s)

To Install the Handles:

NOTE: The handle mounting setscrews are preinstalled in the

handle.

1. Remove the handles, which are packed inside the refrigerator.

NOTE: To avoid scratching the nish, place the handles on a

towel or other soft surface.

2. Open the freezer door. On the refrigerator door, place the

handle on the shoulder screws with the setscrews facing the

freezer.

3. Firmly push the handle toward the door until the handle base

is ush against the door.

4. While holding the handle, insert the short end of the hex key

into the upper hole and slightly rotate the hex key until it is

engaged in the setscrew.

5. Using a clockwise motion, tighten the setscrew until it begins

to contact the shoulder screw.

6. Repeat steps 4 and 5 to begin fastening the lower setscrew.

7. Once both setscrews have been partially tightened as outlined

in the previous steps, fully tighten both the upper and lower

setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed

without this extra tightening.

8. Open the refrigerator door and close the freezer door. Repeat

steps 2 through 7 to install the other handle onto the freezer

door with the setscrews facing the refrigerator.

9. Save the hex key and all instructions.

A. Shoulder screws

B. Setscrews inside the handle

To Remove the Handles:

1. While holding the handle, insert the short end of the hex key

into the lower setscrew hole and slightly rotate the hex key

until it is engaged in the setscrew.

2. Using a counterclockwise motion, loosen the setscrew a

quarter-turn at a time.

3. Repeat steps 1 and 2 for the upper setscrew. Gently pull the

handle away from the door.

4. If necessary, use a Phillips screwdriver to remove the shoulder

screws from the door.

Location Requirements

IMPORTANT: This refrigerator is designed for indoor household

use only.

To ensure proper ventilation for your refrigerator, allow for 1/2"

(1.27 cm) of space on each side and at the top. Allow for 2" (5.08

cm) of space behind the refrigerator. If your refrigerator has an ice

maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a xed wall,

leave a 2" (5.08 cm) minimum space on each side (depending on

your model) to allow the doors to swing open.

NOTES:

■ This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature

range for optimum performance, which reduces electricity

usage and provides superior cooling, is between 60°F (15°C)

and 90°F (32°C). It is recommended that you do not install the

refrigerator near a heat source, such as an oven or radiator.

■ Normal minimum cabinet cut-out width required for product

installation is 36" (91.44 cm). However, if the product is placed

against an extended wall and the ability to remove the crisper

pans is desired, an additional 18" (45.72 cm) of cabinet width

is required, so a total cabinet opening width of 54" (137.16

cm) is recommended.

Electrical Requirements

Before you move your refrigerator into its nal location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 V, 60 Hz, AC only, 15 or 20 A fused, grounded electrical

supply is required. It is recommended that a separate circuit

serving only your refrigerator be provided. Use an outlet that

cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation or cleaning,

or removing a light bulb, disconnect the refrigerator from

the electrical source. When you are nished, reconnect the

refrigerator to the electrical source and reset the control

(Thermostat, Refrigerator or Freezer Control depending on the

model) to the desired setting. See the “Using the Controls”

section in the User Instructions, User Guide, or Use and Care

Guide.

Water Supply Requirements

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

■ Flat-blade screwdriver

■ 7/16" and 1/2" open-end or two adjustable wrenches

■ 1/4" nut driver

■ 1/4" drill bit

■ Cordless drill

NOTE: Your refrigerator dealer has a kit available with a 1/4"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3/16"

(4.76 mm) saddle valve which reduces water ow and clogs more

easily.

WARNING

Explosion Hazard

Keep ammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or re.

2" (1.27 cm)

2" (5.08 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

IMPORTANT:

■ All installations must meet local plumbing code requirements.

■ Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and 120

psi (207 and 827 kPa) is required to operate the water dispenser

and ice maker. If you have questions about your water pressure,

call a licensed, qualied plumber.

■ If your refrigerator has a water dispenser: After installation

is complete, use the water dispenser to check the water

pressure.

■ With the water lter removed, dispense 1 cup (237 mL) of

water. If 1 cup of water is dispensed in 8 seconds or less,

the water pressure to the refrigerator meets the minimum

requirement.

■ If it takes longer than 8 seconds to dispense 1 cup of

water, the water pressure to the refrigerator is lower than

recommended. See “Problem Solver” for suggestions.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of

a reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water ltration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment lter in the reverse

osmosis system is blocked. Replace the lter if necessary.

■ Allow the storage tank on the reverse osmosis system to rell

after heavy usage.

■ If your refrigerator has a water lter, it may further reduce

the water pressure when used in conjunction with a reverse

osmosis system. Remove the water lter. See “Water Filtration

System” in the User Instructions, User Guide, or Use & Care

Guide.

If you have questions about your water pressure, call a licensed,

qualied plumber.

Connect Water Supply

Read all directions before you begin.

IMPORTANT:

■ Connect to potable water supply only.

■ Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

■ The gray water tubing on the back of the refrigerator (which is

used to connect to the household water line) is a plastic

tube. Copper and plastic tubing connections from the

household water line to the refrigerator are acceptable, and

will help avoid off-taste or odor in your ice or water. Check for

leaks.

If plastic tubing is used instead of copper, we recommend the

following Whirlpool Part Numbers:

W10505928RP (7 ft [2.14 m] jacketed plastic),

8212547RP (5 ft [1.52 m] plastic), or

W10267701RP (25 ft [7.62 m] plastic).

■ Install tubing only in areas where temperatures will remain

above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

■ Flat-blade screwdriver

■ 7⁄16" and 1/2" open-end wrenches or two adjustable

wrenches

■ 1/4" nut driver

Connect to Water Line

IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker OFF.

Style 1 (Recommended)

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Use a quarter-turn shutoff valve or the equivalent, served by a

1/2" copper household supply line.

NOTE: To allow sufcient water ow to the refrigerator, a

minimum 1/2" size copper household supply line is

recommended.

4. Now you are ready to connect the copper tubing to the

shutoff valve. Use 1⁄4" (6.35 mm) OD soft copper tubing to

connect the shutoff valve and the refrigerator.

■ Ensure that you have the proper length needed for the job.

Be sure both ends of the copper tubing are cut square.

■ Slip compression sleeve and compression nut onto

copper tubing as shown. Insert end of tubing into outlet

end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not

overtighten.

5. Place the free end of the tubing into a container or sink, and

turn on main water supply to ush out tubing until water is

clear. Turn off shutoff valve on the water pipe.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

A. Bulb

B. Nut

C. Copper tubing (to refrigerator)

D. Household supply line (½" minimum)

B CA

A. Compression sleeve

B. Compression nut

C. Copper tubing

NOTE: Always drain the water line before making the nal

connection to the inlet of the water valve to avoid possible

water valve malfunction.

6. Bend the copper tubing to meet the water line inlet, which

is located on the back of the refrigerator cabinet as shown.

Leave a coil of copper tubing to allow the refrigerator to be

pulled out of the cabinet or away from the wall for service.

Style 2

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a 1/2" (1.27 cm) to 1¼" (3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower rear corner of refrigerator

to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use

1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

5. Using a cordless drill, drill a 1⁄4" (6.35 mm) hole in the cold

water pipe you have selected.

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the ¹⁄4" (6.35 mm)

drilled hole in the water pipe and that the washer is under the

pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so the washer makes a watertight

seal. Do not overtighten, or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on

the copper tubing as shown. Insert the end of the tubing

into the outlet end squarely as far as it will go. Screw the

compression nut onto outlet end with adjustable wrench. Do

not overtighten.

8. Place the free end of the tubing in a container or sink, and

turn ON the main water supply. Flush the tubing until water is

clear. Turn OFF the shutoff valve on the water pipe. Coil the

copper tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the end

of the water line inlet.

3. Thread the nut onto the end of the tubing. Tighten the nut by

hand. Then tighten it with a wrench two more turns. Do not

overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not

touch the cabinet’s side wall or other parts inside the cabinet.

4. Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

5. Turn shutoff valve ON.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the plastic part that is attached to the

inlet of the water valve.

3. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do

not overtighten.

4. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

5. Turn shutoff valve ON.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

7. On some models, the ice maker is equipped with a built-in

water strainer. If your water conditions require a second water

strainer, install it in the 1/4" (6.35 mm) water line at either

tube connection. Obtain a water strainer from your nearest

appliance dealer.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

DEF

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shut-off valve

G. Packing nut

A B C

A. Household water line

B. Nut (purchased)

C. Ferrule (purchased)

D. Refrigerator water tubing

A. Tube clamp

B. Tube clamp screw

C. Copper tubing

D. Compression nut

E. Valve inlet

3. If the gray water tube supplied with the refrigerator is not

long enough, a 1/4" x 1/4" (6.35 mm x 6.35 mm) coupling is

needed in order to connect the water tubing to an existing

household water line. Thread the provided nut onto the

coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Complete the Installation

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See “Water and Ice Dispensers” in

the User Instructions or User Guide.

NOTE: Allow 24 hours to produce the rst batch of ice. Allow 72

hours to completely ll ice container.

REFRIGERATOR CARE

Cleaning

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, ammable uids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water.

4. There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is signicant pet trafc

in the home, the condenser should be cleaned every 2 to 3

months to ensure maximum efciency.

If you need to clean the condenser:

■ Remove the base grille. See the “Door Removal”

instructions, either in the User Instructions or the

Installation Instructions and Owner’s Manual, or in the

separate instruction sheet provided with your refrigerator.

■ Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

■ Replace the base grille when nished.

5. Plug in refrigerator or reconnect power.

A B C D E F G

A. Refrigerator water tubing

B. Nut (provided)

C. Bulb

D. Coupling (purchased)

E. Ferrule (purchased)

F. Nut (purchased)

G. Household water line

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Explosion Hazard

Use nonammable cleaner.

Failure to do so can result in death, explosion, or re.

Lights

IMPORTANT: The lighting system in this appliance may consist

of:

■ Sealed LED modules

■ LED Bulbs

■ Incandescent Bulbs

■ Or a combination of the above.

If a Sealed LED Module(s) do not illuminate when the

refrigerator and/or freezer door is opened, call whirlpool

service for technical support. (See User Guide).

See "Warranty" for contact information.

IF a LED Bulb or incandescent bulb does not turn ON when

the refrigerator and/or freezer door is opened, replace with

a bulb recommended by Whirlpool and following the next

procedure:

1. Unplug refrigerator or disconnect power.

2. Remove light cover (in some models).

NOTE: To clean the light cover, follow the instructions in

REFRIGERATOR CARE section.

3. Remove light bulb and replace with one of the same size,

shape and wattage, recommended by Whirlpool.

4. Reinstall light cover (in some models).

5. Plug in refrigerator or reconnect power.

NOTE: Not all appliance bulbs will t your refrigerator. Be sure to

replace the bulb with one of the same size and shape. On some

models, the interior lights require a 40 W bulb max.

Vacation and Moving Care

Vacations

If You Choose to Leave Refrigerator On While You Are Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker and is

connected to the household water supply, turn off the water

supply to the refrigerator. Property damage can occur if the

water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker.

NOTE: Depending on your model, raise the wire shutoff arm

to OFF (up) position or press the switch to OFF (right).

4. Empty the ice bin.

If You Choose to Turn Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

■ Turn off the water supply to the ice maker at least one day

ahead of time.

■ When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

3. Unplug refrigerator.

4. Clean, wipe, and dry thoroughly.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

■ Turn off the water supply to the ice maker at least one day

ahead of time.

■ Disconnect the water line from the back of the refrigerator.

■ When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Empty the ice bin.

4. Unplug refrigerator.

5. Clean, wipe, and dry thoroughly.

6. Take out all removable parts, wrap them well, and tape them

together so they don’t shift and rattle during the move.

7. Depending on the model, raise the front of the refrigerator so

it rolls more easily OR screw in the leveling legs so they don't

scrape the oor. See “Adjust the Doors” or “Door Removal,

Leveling and Alignment.”

8. Tape the doors closed and tape the power cord to the back of

the refrigerator.

When you get to your new home, put everything back and refer

to the Installation Instructions for preparation instructions. Also,

if your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

FREEZER SHELF

(number of shelves varies by model)

To Remove and Replace the Bottom Shelf:

1. Lift up the front and back of the shelf, and remove from the

cabinet. Be sure not to remove the retaining rods.

2. Replace the shelf aligning the rods with the cabinet ribs.

Apply a little pressure on the shelf to attach the rods to the

ribs of the cabinet.

To Remove and Replace the Mid and Top Shelf:

1. With your hand, push the shelf from bottom to top until it is

released from the holding rod. Pull the shelf until it is released

from the rear rod. Remove from the cabinet.

2. To replace the shelf:

■ Replace rods into the support holes. Push the rods down

so it clicks into the hole.

■ Identify the front and rear trim of the shelf.

■ Place the rear trim on the rear rod and push the shelf so

it clicks the rod into the trim rear. (Keep the front raised

while pushing).

■ Lower the front of the shelf until the front trim is on the rod

and push the shelf down so it clicks the rod into the trim

rear.

NOTE: Be sure that both sides of the shelf are positioned evenly

in the shelf support holes and the shelf is secure.

TROUBLESHOOTING

First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.

GENERAL OPERATION Possible Causes and/or Recommended Solutions

Refrigerator will not operate ■ Not connected to an electrical supply - Plug the power cord into a grounded 3 prong outlet.

Do not use an extension cord.

■ No power to the electrical outlet - Plug in a lamp to see if the outlet is working.

■ Household fuse has blown or circuit breaker has tripped - Replace the fuse or reset the

circuit breaker. If the problem continues, contact a licensed electrician.

■ New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool

completely.

NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either

compartment (refrigerator or freezer) more quickly.

Motor seems to run too much ■ Your new refrigerator has an energy-efcient motor - The refrigerator may run longer than

you’re used to, because the compressor and fans operate at lower speeds that are more energy-

efcient. This is normal.

NOTE: Your refrigerator may run even longer if the room is warm, a large load of food is added,

the doors are opened often, or if a door has been left open.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Refrigerator seems noisy The compressor in your new refrigerator regulates temperature more efciently and uses less energy

than older models. During various stages of operation, you may hear normal operating sounds that

are unfamiliar.

The following noises are normal:

■ Buzzing/Clicking - Heard when the water valve opens and closes to dispense water or ll the

ice maker. If the refrigerator is connected to a water line, this is normal. If the refrigerator is not

connected to a water line, turn off the ice maker.

■ Cracking/Crashing - Heard when ice is ejected from the ice maker mold.

■ Popping - Heard when the inside walls contract/expand, especially during initial cooldown.

■ Pulsating/Whirring - Heard when the fans/compressor adjust to optimize performance during

normal operation.

■ Rattling - Heard when water passes through the water line, or due to the ow of refrigerant.

Rattling may also come from items placed on top of the refrigerator.

■ Water running or gurgling - Heard when ice melts during the defrost cycle and water runs into

the drain pan.

■ Sizzling - Heard when water drips onto the heater during the defrost cycle.

GENERAL OPERATION Possible Causes and/or Recommended Solutions

Temperature

is too warm

■ New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool

completely.

NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either

compartment (refrigerator or freezer) more quickly.

■ Doors are opened often or not closed completely - This allows warm air to enter the

refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors are

properly sealed.

■ Air vents are blocked - Remove items that are immediately in front of the vents.

■ Large amount of warm food recently added - Allow several hours for the refrigerator to return

to its normal temperature.

■ Controls are not set correctly for the surrounding conditions - Adjust the controls to a colder

setting. Check the temperature again in 24 hours.

Temperature is too cold ■ Controls are not set correctly for the surrounding conditions - Adjust the controls to a

warmer setting. Check the temperature again in 24 hours.

■ Top refrigerator shelf is colder than lower shelves - On some models, air from the freezer

enters the refrigerator compartment through vents near the top refrigerator shelf. As a result, the

top shelf can be slightly colder than lower shelves.

■ Air vents are blocked - Remove items that are immediately in front of the vents.

Interior moisture buildup NOTE: Some moisture buildup is normal. Clean with a soft dry cloth.

■ Room is humid - A humid environment contributes to moisture buildup. Use the refrigerator

only in an indoor location, with as little humidity as possible.

■ Doors are opened often or not closed completely - This allows humid air to enter the

refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors are

properly sealed.

Interior lights do not work ■ Doors have been open for an extended period of time - Close the doors to reset the lights.

■ Light bulb is loose in the socket or has burned out - On models with incandescent interior

light bulbs, tighten or replace the bulb. See the “Lights” section.

NOTE: On models with mini LED lights, call for assistance or service if the interior lights do not

illuminate when either door is opened. See the Warranty in the User Instructions or User Guide for

contact information.

Dispenser lights do not work

(on some models)

■ Dispenser light is turned off - On some models, if the dispenser light is set to OFF, the light will

turn on only when a dispenser pad/lever is pressed. If you want the dispenser light to stay on

continuously, select a different setting. See “Water and Ice Dispensers” in the User Instructions

or User Guide.

■ Dispenser light is set to AUTO or NIGHT LIGHT - On some models, if the dispenser light is set

to AUTO or NIGHT LIGHT, make sure the dispenser light sensor is not blocked. See “Water and

Ice Dispensers” in the User Instructions or User Guide.

NOTE: On models with mini LED lights, call for assistance or service if the dispenser lights do not

operate correctly. See the Warranty in the User Instructions or User Guide for contact information.

DOORS AND LEVELING Possible Causes and/or Recommended Solutions

Doors are difcult to open ■ Gaskets are dirty or sticky - Clean the gaskets and contact surfaces with mild soap and

warm water. Rinse and dry with a soft cloth.

Doors will not

close completely

■ Door is blocked open - Move food packages away from the door. Make sure all bins and

shelves are in their correct positions. Make sure all packaging materials have been removed.

Doors appear to be uneven ■ Doors need to be aligned, or refrigerator needs to be leveled - See the leveling and door

alignment instructions.

Refrigerator rocks

and is not stable

■ Refrigerator is not level - To stabilize the refrigerator, remove the base grille and lower the

leveling feet until they touch the oor. See the leveling and door alignment instructions.

ICE AND WATER Possible Causes and/or Recommended Solutions

Ice maker is not

producing ice,

not producing

enough ice,

or producing

small/hollow ice

■ Refrigerator is not connected to a water supply, or the water supply shutoff valve is not fully

turned on - Connect the refrigerator to a water supply and make sure the water shutoff valve is fully

open.

■ Kink in the water source line - A kink in the water line can reduce water ow, resulting in

decreased ice production, small ice cubes, and/or hollow or irregularly-shaped ice. Straighten the

water line.

■ Ice maker is not turned on - Turn on the ice maker. See “Ice Maker and Storage Bin” in the User

Instructions or User Guide.

■ New installation - After connecting the refrigerator to a water source, ush the water system. (See

“Water and Ice Dispensers” in the User Instructions or User Guide.) Wait 24 hours for ice production

to begin. Wait 72 hours for full ice production. Discard the rst three batches of ice produced.

■ Large amount of ice was recently removed - Allow sufcient time for the ice maker to produce

more ice.

■ Ice is jammed in the ice maker ejector arm (on some models) - Remove ice from the ejector arm

using a plastic utensil.

■ Inadequate water pressure - Verify that the household has adequate water pressure. See “Water

Supply Requirements.”

■ Water lter is installed incorrectly - Make sure the lter is properly installed. See “Water Filtration

System” in the User Instructions or User Guide.

■ A reverse osmosis water ltration system is connected to your cold water supply - This can

decrease water pressure. See “Water Supply Requirements.”

NOTE: If questions remain regarding water pressure, contact a licensed, qualied plumber.

WARNING

Explosion Hazard

Use nonammable cleaner.

Failure to do so can result in death, explosion, or re.

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

WARNING

ICE AND WATER Possible Causes and/or Recommended Solutions

Ice dispenser will not

operate properly

■ Doors not closed completely - Make sure both doors are rmly closed. (On some models, only the

freezer door must be closed in order to operate the dispenser.)

■ New installation - After connecting the refrigerator to a water source, ush the water system.

(See “Water and Ice Dispensers” in the User Instructions or User Guide.) Wait 24 hours for ice

production to begin. Wait 72 hours for full ice production. Discard the rst three batches of ice

produced.

■ Ice maker is not turned on, or ice bin is not installed correctly - Turn on the ice maker and make

sure the ice storage bin is rmly in position. See “Ice Maker and Storage Bin” in the User Instructions

or User Guide.

■ Ice is clogged or frozen together in the ice storage bin, or ice is blocking the ice delivery

chute - Remove or separate the clogged ice, using a plastic utensil if necessary. Clean the ice delivery

chute and the bottom of the ice storage bin using a warm damp cloth; then, dry both thoroughly. To

avoid clogging and to maintain a fresh supply of ice, empty the storage bin and clean both the storage

bin and the delivery chute every 2 weeks.

■ Wrong ice has been added to the storage bin - Use only ice cubes produced by the current ice

maker.

■ Dispenser is locked - Unlock the dispenser. See “Water and Ice Dispensers” in the User Instructions

or User Guide.

■ Ice dispenser jams while dispensing crushed ice - For models with the ice storage bin on the door,

temporarily switch from crushed ice to cubed ice to clear the jam.

■ Dispenser pad/lever has been pressed too long - Ice will automatically stop dispensing. Wait a few

minutes for the dispenser to reset, then resume dispensing. Take large amounts of ice directly from the

ice bin, not through the dispenser.

■ Water pressure to the home is not at or above 30 psi (207 kPa) - The water pressure to the home

affects the ow from the dispenser. See “Water Supply Requirements” section.

■ Water lter is clogged or incorrectly installed - Replace lter or reinstall it correctly. See “Water

Filtration System” in the User Instructions or User Guide.

Ice or water has an

off-taste, odor,

or gray color

■ New plumbing connections - New plumbing connections can result in off-avored or discolored ice

or water. This problem should go away over time.

■ Ice has been stored too long - Discard the ice and wash the ice bin. Allow 24 hours for the ice maker

to produce new ice.

■ Odor has transferred from food - Use airtight moisture-proof packaging to store food.

■ Use of non-recommended water supply line - Odors and tastes can transfer from certain materials

used in non-recommended water supply lines. Use only a recommended water supply line. See “Water

Supply Requirements” section.

■ There are minerals (such as sulfur) in the water - A water lter may need to be installed in order to

remove the minerals.

■ Water lter was recently installed or replaced - Gray or dark discoloration in ice or water indicates

that the water ltration system needs additional ushing. See “Water and Ice Dispensers” in the User

Instructions or User Guide.

Water dispenser

will not operate

properly

■ Doors not closed completely - Make sure both doors are rmly closed. (On some models, only the

freezer door must be closed in order to operate the dispenser.)

■ Refrigerator is not connected to a water supply, or the water supply shutoff valve is not turned

on - Connect the refrigerator to a water supply and make sure the water shutoff valve is fully open.

■ Kink in the water source line - A kink in the water line can reduce water ow to the dispenser.

Straighten the water line.

■ Water pressure to the home is not at or above 30 psi (207 kPa) - The water pressure to the home

affects the ow from the dispenser. See “Water Supply Requirements” section.

■ New installation - After connecting the refrigerator to a water source, ush the water system. See

“Water and Ice Dispensers” in the User Instructions or User Guide.

■ Dispenser is locked - Unlock the dispenser. See “Water and Ice Dispensers” in the User Instructions

or User Guide.

■ Water lter is clogged or incorrectly installed - Replace lter or reinstall it correctly. See “Water

Filtration System” in the User Instructions or User Guide.

■ A reverse osmosis water ltration system is connected to your cold water supply - This can

decrease water pressure. See “Water Supply Requirements” section.

NOTE: If questions remain regarding water pressure, contact a licensed, qualied plumber.

ICE AND WATER Possible Causes and/or Recommended Solutions

Water is leaking or dripping

from the dispenser

NOTE: After dispensing, a few additional drops of water are normal.

■ Glass was not held under the dispenser long enough - Hold the glass under the dispenser for

2 to 3 seconds after releasing the dispenser pad/lever.

■ New installation, or water lter was recently installed or replaced - Air in the water lines

causes the water dispenser to drip. Flush the water system to remove the air in the water lines.

See “Water and Ice Dispensers” in the User Instructions or User Guide.

■ Residual ice in the dispenser chute is melting - Make sure the ice chute is free of ice shavings

or pieces.

Water is leaking from the

back of the refrigerator

■ Water line connections are not fully tightened - Make sure all connections are rmly tightened.

See “Connect Water Supply” section.

Water from the dispenser is

not cool enough (on some

models)

NOTE: Water from the dispenser is chilled to 50°F (10°C).

■ New installation - Allow 24 hours after installation for the water supply to cool completely.

■ Recently dispensed a large amount of water - Allow 24 hours for the new water supply to cool

completely.

■ Water has not been recently dispensed - The rst glass of water may not be cool. Discard the

rst glass of water dispensed.

■ Refrigerator is not connected to a cold water pipe - Make sure the refrigerator is connected to

a cold water pipe. See “Water Supply Requirements” section.

PERFORMANCE DATA SHEET

Water Filtration System

Model P5WB2L/P4RFWB Capacity 200 Gallons (757 Liters)

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below.

The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specied in NSF/ANSI Standards 42 and 53.

Substance

Reduction

Aesthetic Effects

NSF Reduction

Requirements

Average

Inuent

Inuent Challenge

Concentration

Maximum

Efuent

Minimum %

Reduction

Average %

Reduction

Chlorine Taste/Odor

Particulate Class I*

50% reduction

85% reduction

2.0 mg/L

7,300,000 #/mL

2.0 mg/L ± 10%

At least 10,000 particles/mL

0.20 mg/L

75,000 #/mL**

97.2

99.4

Contaminant

Reduction

NSF Reduction

Requirements

Average

Inuent

Inuent Challenge

Concentration

Maximum

Efuent

Minimum %

Reduction

Average %

Reduction

Live Cysts

†

99.95% 160,000/L 50,000/L min. 54/L

†

99.97 99.99

Asbestos 99% 87 MFL 10

to 10

bers/L

††

0.17 MFL 99 99

Lead: @ pH 6.5

Lead: @ pH 8.5

0.010 mg/L 0.010

mg/L

0.160 mg/L 0.140

mg/L

0.15 mg/L ± 10%

0.001 mg/L

0.005 mg/L

99.4

98.6

99.4

98.6

Lindane 0.0002 mg/L 0.0019 mg/L 0.002 mg/L ± 10% 0.00002 mg/L 98.9 99

Toxaphene 0.003 mg/L 0.014 mg/L 0.015 mg/L ± 10% 0.001 mg/L 93 93

Atrazine 0.003 mg/L 0.0094 mg/L 0.009 mg/L ± 10% 0.0005 mg/L 94.5 94.7

2,4 - D 0.07 mg/L 0.220 mg/L 0.210 mg/L ± 10% 0.028 mg/L 87.5 96.1

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa).

Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).

■ It is important that operational, maintenance, and lter

replacement requirements be carried out for the product

to perform as advertised. Property damage can occur if all

instructions are not followed.

■ Use replacement lter according you ltration system, see“Ice

and Water” in the User Guide.

Water Filter:

Water Filtration System Style 1 - Order Part # EDR1RXD1

Water Filtration System Style 2 - Order Part # EDR2RXD1

When the water lter status changes from TURN OFF to

RED light on your control panel, it is recommended that you

replace the lter.

■ After changing the water lter, ush the water system. See

“Water and Ice Dispensers” or “Water Dispenser” in the User

Instructions or User Guide.

■ These contaminants are not necessarily in your water supply.

While testing was performed under standard laboratory

conditions, actual performance may vary.

■ The product is for cold water use only.

■ The water system must be installed in compliance with state

and local laws and regulations.

■ Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system. Systems certied for cyst reduction may be used

on disinfected waters that may contain lterable cysts.

■ Refer to the “Warranty” section (in the User Instructions

or User Guide) for the Manufacturer’s name, address and

telephone number.

■ Refer to the “Warranty” section (in the User Instructions or

User Guide) for the Manufacturer’s limited warranty.

Application Guidelines/Water Supply Parameters

Water Supply

Water Pressure

Water Temperature

Service Flow Rate

City or Well

30 - 120 psi (207 - 827 kPa)

33° - 100°F (0.6° - 37.8°C)

0.5 gpm (1.9 Lpm) @ 60 psi

System tested and certied by NSF International against NSF/ANSI

Standard 42 for the reduction of Chlorine Taste and Odor, and Particulate

Class I*; and against NSF/ANSI Standard 53 for the reduction of Live

Cysts, Asbestos, Lead, Lindane, Toxaphene, Atrazine, and 2,4 - D.

*Class I particle size: >0.5 to <1 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

†

Based on the use of Cryptosporidium parvum oocysts

††

Fibers greater than 10 um in length

NSF is a registered trademark of NSF International.

SÉCURITÉ DU RÉFRIGÉRATEUR

Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

Risque possible de décès ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Votre sécurité et celle des autres est très importante.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de

toujours lire tous les messages de sécurité et de vous y conformer.

AVERTISSEMENT

DANGER

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous

et à d’autres.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou

“AVERTISSEMENT”. Ces mots signifient :

AVERTISSEMENT :

Pour réduire le risque d’incendie, de choc électrique ou de blessure dans le cadre de l’utilisation du

réfrigérateur, suivre les consignes de base suivantes :

IMPORTANTES INSTRUCTIONS DE SÉCURITÉ

CONSERVEZ CES INSTRUCTIONS

■

Brancher sur une prise de terre (reliée à la masse).

■

Ne pas retirer la broche de terre.

■

Ne pas utiliser d’adaptateur.

■

Ne pas utiliser de rallonge.

■ Débrancher la source de courant électrique avant l'entretien.

■ Replacer pièces et panneaux avant de faire la remise en marche.

■ Enlever les portes de votre vieux réfrigérateur.

■

Raccorder uniquement à une arrivée d’eau potable.

■ Utiliser un produit de nettoyage ininflammable.

■

Ne pas utiliser ou conserver d’essence ni de liquides ou gaz

inflammables à proximité de cet ou d’autres appareils électriques. Les

fumées peuvent causer des incendies ou des explosions.

■ Utiliser deux ou plus de personnes pour déplacer et installer le

réfrigérateur.

■ Débrancher le réfrigérateur avant l'installation de la machine à

glaçons (seulement pour modèles prêts à recevoir une machine

à glaçons).

■ Utiliser un verre robuste pour prendre des glaçons (sur certains

modèles).

■ Ne pas heurter les portes en verre du réfrigérateur (sur

certains modèles).

■ Cet appareil ne convient pas à une utilisation par des

personnes (y compris des enfants) à capacités physiques,

sensorielles ou mentales réduites, ou possédant un

manque d’expérience et de connaissances, à moins

qu’elles ne soient placées sous supervision ou qu’elles

aient reçu des instructions concernant l’utilisation de

l’appareil par une personne responsable de leur sécurité.

■

Les enfants doivent être placés sous surveillance afin de

s’assurer qu’ils ne jouent pas avec l’appareil.

■

Si le cordon d’alimentation est endommagé, il doit être remplacé

par le fabricant, son agent de réparation ou toute autre personne

qualifiée afin d’éviter tout danger.

■

Ne pas entreposer de substances explosives comme des

aérosols avec agent propulseur inflammable dans cet appareil.

■

Cet appareil est destiné à un usage domestique et à d’autres

usages similaires comme :

– espace de cuisine pour personnel de boutiques, bureaux et

autres environnements professionnels;

– résidences fermières et utilisation par les clients d’hôtels, de

motels et d’autres types de résidences;

– environnements de type chambres d’hôtes;

– Banquets et autres utilisations non commerciales semblables.

Mise au rebut du vieux réfrigérateur

IMPORTANT: Le risque qu’un enfant puisse se retrouver coincé

et suffoquer n’est pas chose du passé. Les réfrigérateurs jetés ou

abandonnés restent dangereux, même s’ils ne restent à l’extérieur

que pour “quelques jours seulement”. Si l’ancien réfrigérateur doit

être mis au rebut, suivre les instructions suivantes an d’éviter les

accidents.

Avant de jeter l’ancien réfrigérateur ou congélateur:

■ Enlever les portes.

■ Laisser les tablettes en place de sorte que les enfants ne

puissent pas y pénétrer facilement.

INSTRUCTIONS D’INSTALLATION

Déballage du réfrigérateur

Enlever les matériaux d’emballage. Ne pas utiliser d’instruments

coupants, d’alcool à friction, de liquides inammables ou de

nettoyants abrasifs pour enlever le ruban adhésif ou la colle.

Ces produits peuvent endommager la surface du réfrigérateur.

Pour plus de renseignements, voir la section “Sécurité du

réfrigérateur”.

AVERTISSEMENT

Risque de suffoquer

Enlever les portes de votre vieux réfrigérateur.

Le non-respect de cette instruction peut causer

un décès ou des lésions cérébrales.

Renseignements importants à propos de la mise au

rebut des fluides réfrigérants :

Mettre le réfrigérateur au rebut conformément à la

réglementation fédérale et locale. Les fluides réfrigérants

doivent être évacués par un technicien certifié et agréé par

l’EPA conformément aux procédures établies.

AVERTISSEMENT

Risque du poids excessif

Utiliser deux ou plus de personnes pour déplacer et

installer le réfrigérateur.

Le non-respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

Déplacement de votre réfrigérateur :

Votre réfrigérateur est lourd. Lors du déplacement de votre

réfrigérateur pour le nettoyage ou un entretien ou réparation,

veiller à recouvrir le plancher avec du carton ou un panneau

de fibres dures pour éviter qu'il ne subisse tout dommage.

Toujours tirer le réfrigérateur tout droit lors de son

déplacement. Ne pas incliner le réfrigérateur d’un côté ou de

l’autre ni le “faire marcher” en essayant de le déplacer car le

plancher pourrait être endommagé.

Importants renseignements à savoir au sujet des tablettes

et des couvercles en verre :

Ne pas nettoyer les tablettes ou couvercles en verre avec de

l’eau tiède quand ils sont froids. Les tablettes et les

couvercles peuvent se briser s'ils sont exposés à des

changements soudains de température ou à un impact tel

que coup brusque. Le verre trempé est conçu pour éclater

en d’innombrables pièces minuscules. Ceci est normal. Les

tablettes et les couvercles en verre sont lourds. Les saisir à

deux mains lors de leur dépose afin d'éviter de les faire

tomber.

Retrait, mise au niveau et alignement des portes

Rassembler les outils et pièces nécessaires et lire toutes les instructions avant de commencer l’installation. Conserver ces instructions

pour référence ultérieure.

REMARQUE: En cas de déménagement, prendre les mesures de l’entrée de l’habitation, avant de déplacer l’appareil, an de

déterminer s’il est nécessaire de démonter la porte du réfrigérateur et celle du congélateur. Si les portes doivent être retirées, voir les

instructions ci-dessous.

IMPORTANT: Avant de commencer, débrancher le réfrigérateur ou déconnecter la source de courant électrique. Retirer les aliments,

lebac d’entreposage des glaçons (sur certains modèles) et tout balconnet ajustable ou compartiment utilitaire des portes.

OUTILS REQUIS: Niveau à bulle, tournevis à lame plate, clés de 5/16 po et 11/16 po, clés à douille à tête hexagonale de 1/4 po, 3/8 po

et 5/16 po, tournevis cruciforme no2 d’une longueur minimum de 4po et tournevis TORXT30

†

AVERTISSEMENT

Risque de choc électrique

Déconnecter la source de courant électrique avant d'enlever les portes.

Le non-respect de cette instruction peut causer un décès ou un choc électrique.

A CB

Charnière supérieure

gauche

Retrait des portes Charnière supérieure

droite

Charnières inférieures gauche

et droite

Câblage

Tuyau du distributeur

d’eau

Réfrigérateur complet

Grille de la base

Porte du ltre à eau et grille de

la base

Vis d’alignement

Écrou de blocage

Vis d’ajustement de l’aplomb

Ne pas retirer les vis A

Ne pas retirer les vis B

A. Fiches de câblage

B. Agrafe de câblage

C. Œillets

A. Avant du raccord

A. Tirer vers la droite pour extraire

B. Tourner et passer sous la porte

Tirer vers soi.

Vis à tête cruciforme

Abaisser

Relever

Clé de

5/16 po

Desserrer

Serrer

Clé de

11/16 po

Relever

Abaisser

Relever

Caisse

Porte du

congélateur

Roulettes avant ajustables

Porte du

ltre à eau

Grille de

la base

Porte du

réfrigérateur

†

TORX et T30 sont des marques déposées de Acument Intellectual Properties, LLC.

La page est en cours de chargement...

Whirlpool WRS321SDHW Guide d'installation

Marque: Whirlpool

Modèle: WRS321SDHW

Catégorie: Frigos

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool WRS321SDHW Installation guide

Whirlpool WRS321SDHW Guide d'installation

Whirlpool WRS321SDHW Guide d'installation

dans d''autres langues

Documents connexes

Autres documents