Toro Powervac Gas-Powered Blower Manuel utilisateur

Powervac

™

Item No. 51988—315000001 & Up

English (EN), French (FR), and Spanish (ES)

WARNING:

To reduce the risk of injury, the user must read and understand the Operator’s Manual. Save this manual.

Form No. 3389-623 Rev. A

If you have questions concerning

your blower, please call us

at 1-866-574-9242 (US) or

1-866-574-9243 (Canada).

NOTICE

Do not use E15 or E85 fuel in this product.

Only use unleaded gasoline containing up

to 10% ethanol. It is a violation of federal

law and will damage the unit and void your

warranty.

®

2

READ THIS INFORMATION

Before you use your new Powervac

™

, read the following helpful hints to

get you started.

Fueling

WARNING:

Gasoline and its vapors are highly ammable and

explosive. To prevent serious personal injury and

property damage, handle it with care. Keep away

from ignition sources and open ames, handle

outdoors only, do not smoke and wipe up spills

immediately.

1. Obtain a clean container that is approved for use with gasoline.

2. Mix all of the 2-cycle oil provided with 1 US gallon of 87-octane, unleaded

gasoline (50:1).

3. Fill the blower’s fuel tank carefully.

Cold Starting vs. Warm Starting

When you restart the blower and you are not sure whether the engine is still warm, set the choke

lever to RUN, lock the throttle wide open, and pull the starter grip and rope. If the engine does not

start within 5 pulls, refer to “To Start a Cold Engine” later in this manual.

Flooded Engine

Will the engine start? If not, it may be ooded. Relax, this is easy to correct. Set the choke lever to

RUN. Squeeze the trigger and pull the starter grip and rope quickly for 10 to 12 pulls.

If the engine does not start, refer to Troubleshooting later in this manual or call toll-free at

866-574-9242 (US) or 866-574-9243 (Canada).

CALL

1-866-574-9242 (US) or

1-866-574-9243 (Canada)

For questions concerning your blower,

call us toll free at 1-866-574-9242 (US) or

1-866-574-9243 (Canada).

WARNING: This product, its exhaust, and other substances that may become airborne

from its use may contain chemicals, including lead, known to the State of California to cause cancer,

birth defects, or other reproductive harm. Wash hands after handling.

California Proposition 65

STOP

3

Table of Contents

Introduction ................................................................................................................................................................................... 4

General Safety Rules .....................................................................................................................................................................5

Specic Safety Rules ....................................................................................................................................................................6

Symbols.........................................................................................................................................................................................7

Product Labels ..............................................................................................................................................................................8

Features ................................................................................................................................................................................... 9-10

Product Specications ...........................................................................................................................................................9

Know Your Blower/Vacuum ................................................................................................................................................ 10

Assembly................................................................................................................................................................................11-13

Unpacking ............................................................................................................................................................................11

Packing List .........................................................................................................................................................................11

Tools Needed .......................................................................................................................................................................11

Assembling the Blower Tubes ............................................................................................................................................. 11

Installing the Vacuum Bag ................................................................................................................................................... 12

Installing the Vacuum Tubes ................................................................................................................................................ 13

Operation ............................................................................................................................................................................... 14-17

Applications .........................................................................................................................................................................14

Fueling and Refueling ..........................................................................................................................................................14

Oxygenated Fuels ................................................................................................................................................................15

Starting and Stopping ..........................................................................................................................................................15

Operating the Blower ........................................................................................................................................................... 16

Throttle Lock .......................................................................................................................................................................17

Vacuum Operation ...............................................................................................................................................................17

Maintenance .......................................................................................................................................................................... 18-20

General Maintenance ...........................................................................................................................................................18

Cleaning the Product ............................................................................................................................................................18

Servicing the Product ........................................................................................................................................................... 18

Checking the Fuel Cap, Tank and Lines ..............................................................................................................................18

Cleaning the Air Filter .........................................................................................................................................................19

Cleaning the Exhaust Port, Mufer and Spark Arrestor ......................................................................................................19

Vacuum Bag ......................................................................................................................................................................... 19

Spark Plug Replacement ...................................................................................................................................................... 19

Storing the Product ..............................................................................................................................................................20

High Altitude Engine Operation ..........................................................................................................................................20

Maintenance Schedule .........................................................................................................................................................20

Troubleshooting ..........................................................................................................................................................................21

Warranty ...................................................................................................................................................................................... 22

Table of Contents

4

®

Introduction

Thank you for purchasing a Toro product.

We would like for you to be completely satised with your new product, so feel free to contact a qualied service dealer for

help with service, genuine Toro parts, or other information you may require.

Whenever you contact a qualied service dealer, always know the model and serial numbers of the product. These numbers

will help the service representative provide exact information about your specic product. You will nd the model and serial

number data label located on the bottom of the housing.

For your convenience, write the product model and serial numbers in the space below.

Item No.

Serial No.

Manufactuing No.

Read this manual carefully to learn how to operate and maintain your product correctly. Reading this manual will help you

and others avoid personal injury and damage to the product. Although Toro designs, produces, and markets safe, state-of-the-

art products, you are responsible for using the product properly and safely. You are also responsible for training persons you

allow to use the product about safe operation.

The Toro warning system in this manual identies potential hazards and has special safety messages that help you and others

avoid personal injury, even death. DANGER, WARNING, and CAUTION are signal words that identify the level of hazard.

However, regardless of the hazard, be extremely careful. Two other words, “Important” and “Note,” highlight information.

Introduction

Data

Label

Bottom View

5

Read All Instructions



Do not allow children or untrained individuals to use

this unit.

 Do not start or operate the engine in a conned space,

building, near open windows, or in other unventilated

space where dangerous carbon monoxide fumes can

collect. Carbon monoxide, a colorless, odorless, and

extremely dangerous gas, can cause unconsciousness or

death.



Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protec-

tion. Failure to do so could result in objects being

thrown into your eyes and other possible serious inju-

ries.



Keep all bystanders, children, and pets at least 50 ft.

away.



Wear heavy long pants, long sleeves, boots, and gloves.

Do not wear loose tting clothing, short pants, sandals,

jewelry of any kind, or go barefoot.



To reduce the risk of injury associated with objects

being drawn into rotating parts, do not wear loose cloth-

ing, scarves, neck chains, etc.



Secure long hair so it is above shoulder level to prevent

entanglement in any rotating parts.



Do not operate this unit when you are tired, ill, upset, or

under the inuence of alcohol, drugs, or medication.



Do not operate in poor lighting.



Keep all parts of your body away from any moving

parts and all hot surfaces of the unit.



Wear a face lter mask in dusty conditions to reduce the

risk of injury associated with the inhalation of dust.



Check the work area before each use. Remove all

objects such as rocks, broken glass, nails, wire, or

string which can be thrown or become entangled in the

machine.



Keep rm footing and balance. Do not overreach. Over-

reaching can result in loss of balance or exposure to hot

surfaces.



Before storing, allow the engine to cool.



Empty fuel tank into a container approved for gasoline

and restrain the unit from moving before transporting in

a vehicle.



To reduce the risk of re and burn injury, handle fuel

with care. It is highly ammable.



Do not smoke while handling fuel.



Mix and store fuel in a container approved for gasoline.



Mix fuel outdoors where there are no sparks or ames.



Select bare ground, stop engine, and allow to cool

before refueling.



Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.



Tighten the fuel cap securely after refueling.



Wipe spilled fuel from the unit. Move 30 ft. away from

refueling site before starting engine.



Never attempt to burn off spilled fuel under any circum-

stances.



Maintain the unit per maintenance instructions in this

Operator’s Manual.



Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace damaged parts.



Do not use on a ladder, rooftop, tree, or other unstable

support. Stable footing on a solid surface enables better

control of the blower in unexpected situations.

Service



Before cleaning, repairing, or inspecting, shut off the

engine and make certain all moving parts have stopped.

Disconnect the spark plug wire, and keep the wire away

from the plug to prevent starting.



We recommend taking your equipment to a qualied

service center for repair, as service performed by

inexperienced or unqualied persons may damage the

equipment, create unsafe conditions, injury to user and/

or void your warranty.



Use only recommended or equivalent replacement parts

and accessories. Use of any other parts may create a

hazard or cause product damage.

General Safety Rules

WARNING:

Read and understand all instructions. Failure to follow all instructions listed below may result in electric

shock, re and/or carbon monoxide poisoning which will cause death or serious personal injury.

6

Specific Safety Rules



Always hold the blower/vacuum in your right hand dur-

ing blower operation. Refer to the Operation instruc-

tions later in this manual for proper position during

vacuum operation and additional information.



Never place objects inside the blower tubes.



Use only as directed in this operator’s manual.



Do not operate vacuum without vacuum bag installed;

ying debris could cause serious injury. Always close

vacuum bag completely before operating.



Rotating impeller blades can cause severe injury. Stop

the engine and ensure impeller blades have stopped

rotating before opening the vacuum door or installing/

changing tubes. Do not put hands or any other object

into the vacuum tubes while they are installed on the

unit.



Never run the unit without the proper equipment

attached. When used as a blower, always install the

blower tubes. When used as a vacuum, always install

the vacuum tubes and vacuum bag. Make sure the

vacuum bag is completely zipped when the unit is run-

ning to avoid ying debris.



Avoid situations that could catch the vacuum bag on

re. Do not operate near an open ame. Do not vacuum

warm ash from replaces, barbecue pits, brush piles,

etc. Do not vacuum discarded cigars or cigarettes unless

the cinders are completely cool.



Never place blower on any surface, except a hard, clean

surface when engine is running. Gravel, sand, and other

debris can be picked up by the air inlet and thrown at

the operator or bystanders, causing possible serious

injuries.



To reduce the risk of hearing loss associated with sound

level(s), hearing protection is required.



To reduce the risk of injury associated with contact-

ing rotating parts, stop the engine before installing or

removing attachments. Always disconnect the spark

plug before performing maintenance or accessing any

movable parts.



Never use blower near res, replaces, hot ashes, bar-

becue pits, etc., which may cause re to spread.



Do not point the blower nozzle in the direction of

people or pets.



Never run the unit without the proper equipment at-

tached. Always ensure the blower tubes are installed.



This product is intended for infrequent use by home-

owners and other occasional users for such general ap-

plications as blowing leaves and lawn clippings, etc. It

is not intended for prolonged use. Prolonged periods of

operation can cause circulatory problems in the user’s

hands due to vibration. For such use, it may be appro-

priate to use a product having an anti-vibration feature.

Fueling



Fuel is highly ammable. Take precautions when using

to reduce the chance of serious personal injury.



Store fuel in a cool, well-ventilated area, safely away

from spark and/or ame-producing equipment.



Store fuel in containers specically designed for this

purpose.



Only refuel outdoors and do not smoke while refueling.



Add fuel before starting the engine. Never remove the

cap of the fuel tank or add fuel while the engine is run-

ning or when the engine is hot.



Do not smoke while handling fuel.



Mix and store fuel in a container approved for gasoline.



Mix fuel outdoors where there are no sparks or ames.



Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.



Tighten the fuel cap securely after refueling.



Wipe spilled fuel from the unit. Move 30 feet away

from refueling site before starting engine.



Never attempt to burn off spilled fuel under any circum-

stances.



To reduce the risk of re and burn injury, handle fuel

with care. It is highly ammable.



If fuel is spilled, do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until fuel vapors

have dissipated.



Replace all fuel tank and container caps securely.



Empty fuel tank into a container approved for gasoline

and restrain the unit from moving before transporting in

a vehicle.



When draining the fuel tank, use an approved fuel stor-

age container in a well-ventilated area.



Select bare ground, stop engine, and allow to cool

before refueling.



Save these instructions. Refer to them frequently and

use them to instruct others who may use this tool. If

you loan someone this tool, loan them these instructions

also.

7

Symbols

The following signal words and meanings are intended to explain the levels of risk associated with this

product.

SYMBOL SIGNAL MEANING

DANGER: Indicates an imminently hazardous situation, which, if not avoided, will

result in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could

result in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may

result in minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates important information not related

to an injury hazard, such as a situation that may result in property damage.

Symbols

Some of the following symbols may be used on this product. Please study them and learn their meaning for safe

operation of this product.

SYMBOL NAME EXPLANATION

Safety Alert Symbol Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand opera-

tor’s manual before using this product.

Wear Eye and Hearing

Protection

Always wear eye protection with side shields marked to comply

with ANSI Z87.1 as well as hearing protection when operating

this equipment.

Keep Bystanders Away Keep all bystanders at least 50 ft. away.

Ricochet

Thrown objects can ricochet and result in personal injury or

property damage.

Vacuum Door Do not run unit while vacuum door is unsecured.

Long Hair Risk of long hair being drawn into air inlet.

Blower Tubes Do not run unit without tubes in place.

Loose Clothing Risk of loose clothing being drawn into air intake.

Gasoline and Lubricant

Use unleaded gasoline intended for motor vehicle use with an oc-

tane rating of 87 [(R + M) / 2] or higher. This product is powered

by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle

lubricant.

Stop Symbol

To stop the engine, press and hold the stop switch in the stop

position

8

Product Labels

Product labels and instructions are easily visible to the operator and are located near any area of potential danger.

Replace damaged or lost labels.

Product Labels

Part No. 941727005 Part No. 940908003

Part No. 940907028

Part No. 940835008

Part No. 940654088

Part No. 940907027

Part No. 940907029

Part No. 941727006 Part No. 940991054

Part No. 527990001

Part No. 941727009

9

®

Figure 1

Features

Product Specifications

Name Specification

Engine 25.4cc Full Crank

Air Velocity

MPH Up to 150 (241.39 kph)

CFM Up to 460 (13 m

3

/min)

Features

Upper

Vacuum Tube

Vacuum Bag

Raised Slot

Lower

Vacuum Tube

Vacuum Bag

Shoulder Strap

Vacuum Tube

Screw

Main

Housing

®

Primer Bulb

Muffler

Starter Grip

and Rope

Vacuum Handle

Fuel Cap

Air Filter

Cover Tab

Upper Handle

Throttle

Lock

Throttle

Trigger

Spark Plug

Choke Lever

RUN

HALF

FULL

Stop Switch

Vacuum Bag

Adaptor

10

®

Know Your Blower/Vacuum

See Figures 1 - 2.

The safe use of this product requires an understanding of the

information on the tool and in this operator’s manual as well

as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

Blower Tube and Sweeper Nozzle

The blower tubes and sweeper nozzle can be assembled and

installed on the main housing using no tools.

Engine

The blower has a powerful 25.4cc engine with sufcient

power to handle tough blowing and vacuuming jobs.

Mulcher

The blower is equipped with a metal mulching blade that

efciently reduces leaves at a 10:1 ratio.

Sweeper Nozzle

The sweeper nozzle allows for more area to be covered

during blower operation.

Throttle Lock

The throttle lock feature allows the user to operate the

blower without holding the throttle trigger. To slow the

engine speed, simply push the throttle lock forward.

Throttle Trigger

The blower can be operated at any speed between idle and

full throttle.

Vacuum/Mulcher

Converting the blower to a vacuum/mulcher is simple and

can be done using a straight screwdriver.

Vacuum Bag

The vacuum bag attaches to the main housing easily by

using the vacuum bag adaptor.

Vacuum Handle

This feature allows user to perform vacuuming duties

comfortably.

Vacuum Tubes

The vacuum tubes can be installed on the main housing

using a at head screw driver.

Features

Figure 2

Upper

Handle

Upper

Blower Tube

Muffler

Vacuum

Inlet Door

Throttle

Lock

Throttle

Trigger

Sweeper Nozzle

Stop Switch

Main

Housing

11

Assembly

Flat Head Screwdriver

WARNING:

Do not attempt to modify this product or create

accessories not recommended for use with this

product. Any such alteration or modication is

misuse and could result in a hazardous condition

leading to possible serious personal injury.

WARNING:

To prevent accidental starting that could cause

serious personal injury, always disconnect the

engine spark plug wire from the spark plug

when assembling parts.

Tools Needed

The following tool (not included or drawn to scale) is

needed for assembly:

Unpacking

This product requires assembly.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing

list are included.

WARNING:

Do not use this product if any parts on the Pack-

ing List are already assembled to your product

when you unpack it. Parts on this list are not as-

sembled to the product by the manufacturer and

require customer installation. Use of a product

that may have been improperly assembled could

result in serious personal injury.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have

carefully inspected and satisfactorily operated the

product.

 If any parts are damaged or missing, please call

1-866-574-9242 (US) or 1-866-574-9243 (Canada) for

assistance.

Packing List

Blower

Upper Blower Tube

Sweeper Nozzle

Upper and Lower Vacuum Tubes

Vacuum Tube Screws (2)

Vacuum Bag Assembly

Vacuum Bag Adaptor

2-Cycle Engine Lubricant

Operator’s Manual

Note: Read and remove all hang tags and store with your

Operator’s Manual.

WARNING:

If any parts are damaged or missing do not

operate this product until the parts are replaced.

Use of this product with damaged or missing

parts could result in serious personal injury.

Figure 3

Sweeper

Nozzle

Upper

Blower Tube

Main Housing

Outlet

Raised

Locking Tab

Assembling and Disassembling the

Upper Blower Tube and Sweeper

Nozzle

See Figure 3 - 4.

1. Align raised tabs on main housing to the slots on upper

tube; slide together and tighten securely by twisting.

Check tightness after initial run and retighten if needed.

2. Secure the sweeper nozzle and upper blower tube

together by aligning the raised locking tab on the upper

blower tube with the raised slot on the sweeper nozzle.

3. To disassemble, raise the locking tab with a at head

screwdriver, rotate the tube and nozzle to unlock them

and remove from the main housing outlet.

12

Installing the Vacuum Bag

See Figures 5 - 6.

1. Remove the sweeper nozzle and upper blower tube

from the main housing by twisting and removing from

main housing outlet.

2. Unzip the vacuum bag and place the adaptor inside

as shown. Push the vacuum bag adaptor through the

opening opposite the zipper. The wider end of the adap-

tor will remain on the inside of the vacuum bag when

installed properly.

3. Align the raised slots on the vacuum bag adaptor with

the raised locking tabs on the main housing outlet; push

the bag adaptor onto the housing. Twist to lock into

place.

4. Rotate the vacuum bag until the shoulder strap is up-

right.

5. Make sure the vacuum bag is zipped and closed before

starting the unit.

Assembly

To remove the vacuum bag:

1. Remove the vacuum bag by using a at head screw-

driver to lift the locking tab.

2. Rotate counterclockwise to unlock the adaptor and

remove.

Figure 5

Vacuum Bag Adaptor

Vacuum Bag

Figure 6

Vacuum Bag

Adaptor Installed

to housing

Raised

Locking

Tab

Main

Housing

Outlet

Figure 7

Vacuum

Inlet Door

Vacuum

Door

Hinge

Door Tab

Vacuum Bag

Assembly

Raised

Tab

Figure 4

®

Tab

Blower /

Vacuum Tube

13

®

Assembly

Figure 9

Upper

Vacuum Tube

Lower

Vacuum Tube

Screws

Slots

Tabs

Upper

Vacuum Tube

Slot

Vacuum

Inlet Door

Lock

Unlock

Installing the Vacuum Tubes

See Figures 7 - 9

WARNING:

Rotating impeller blades can cause severe injury.

Always stop the engine and ensure impeller

blades have stopped rotating before opening the

vacuum door or installing/changing tubes. Do

not put hands or any other object into the vacuum

tubes while they are installed on the unit.

Tab

Vacuum Tube

Figure 8

To install the vacuum tubes:

1. Secure the upper and lower vacuum tubes together by

aligning the raised locking tabs with the raised slots.

2. Tap tube assembly on ground until the screw holes

in lower tube are in the raised slot of the upper tube.

Secure with supplied screws.

3. Depress door tabs using a straight screwdriver and open

vacuum inlet door.

4. Align the slots on the vacuum tube housing with the

tabs on the main housing.

5. Turn the vacuum tube housing clockwise to to the

locked position and secure to the main housing.

To remove the vacuum tubes:

1. Using a screwdriver, depress the tab on the blower/

vacuum tube to unlock.

2. Turn the upper vacuum tube housing counterclockwise.

3. Remove the vacuum tube assembly from the main

housing.

4. Close the inlet cover door securely.

Vacuum

Tube Housing

Tabs

Vacuum

Opening

14

Operation

WARNING:

Do not allow familiarity with tools to make you

careless. Remember that a careless fraction of a

second is sufcient to inict serious injury.

WARNING:

Always wear eye protection with side shields

marked to comply with ANSI Z87.1, along with

hearing protection. Failure to do so could result

in objects being thrown into your eyes and other

possible serious injuries.

NOTICE:

The spark arrestor on this product has not been

evaluated by the USDA Forest Service and

cannot be used on U.S. forest lands. In addition,

product users must comply with Federal, State,

and local re prevention regulations. Check

with appropriate authorities. Contact customer

service or a qualied service center to purchase

a replacement spark arrestor.

NOTICE:

Before each use, inspect the entire product for

damaged, missing, or loose parts such as screws,

nuts, bolts, caps, etc. Tighten securely all fasten-

ers and caps and do not operate this product until

all missing or damaged parts are replaced. Please

contact customer service or a qualied service

center for assistance.

Applications

You may use this tool for the purposes listed below:

 Clear leaves and other debris from your lawn

 Keep decks and driveways free from leaves and pine

needles

 Vacuuming leaves from your lawn

Fueling and Refueling

WARNING:

Gasoline is extremely ammable and explosive.

A re or explosion from gasoline will burn you

and others. Always shut off engine before fuel-

ing. Never add fuel to a machine with a running

or hot engine. Move at least 30 ft. from refuel-

ing site before starting engine. Do not smoke

and stay away from open ames and sparks.

Failure to safely handle fuel could result in seri-

ous personal injury.

Fuel Mixture

This product is powered by a 2-cycle engine and requires

pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded

gasoline and 2-cycle engine lubricant in a clean container

approved for gasoline. DO NOT mix quantities larger than

usable in a 30-day period.

Recommended fuel: This engine is certied to operate on

unleaded gasoline intended for automotive use.

Ethanol. Gasoline containing up to 10% ethanol by volume

(commonly referred to as E10) is acceptable. E15 and E85

are not.

Note: We recommend you use high-quality synthetic 2-cycle

lubricant in this product. Mix at 2.6 oz. per gallon US (76 ml

par 3,8 L ).

Do not use automotive lubricant or 2-cycle outboard

lubricant.

HIGH QUALITY 2-CYCLE ENGINE LUBRICANT

GASOLINE LUBRICANT

1.0 gal. (US) (3.8 liter) 2.6 oz. (76 ml)

2.5 gal. (US) (9.5 liter) 6.4 oz. (189 ml)

Filling the Tank

1. Clean the surface around the fuel cap to prevent con-

tamination.

2. Loosen the fuel cap slowly, by turning it counterclock-

wise.

3. Pour the fuel mixture carefully into the tank.

4. Clean and inspect the fuel cap gasket before replacing

the fuel cap.

5. Replace the fuel cap and tighten it by turning it clock-

wise.

6. Wipe spilled fuel from the product.

7. Move at least 30 ft. (9 m) away from refueling area

before starting the product.

Note: It is normal for smoke to be emitted from a new

engine during rst use.

Operation

15

Operation

WARNING:

Always shut off engine before fueling. Never

add fuel to a machine with a running or hot

engine. Move at least 30 ft (9 m). from refueling

site before starting engine. Do not smoke and

stay away from open ames and sparks. Fail-

ure to safely handle fuel could result in serious

personal injury.

Oxygenated Fuels

NOTICE:

Do not use E15 or E85 fuel in this product.

Only use unleaded gasoline containing up to

10% ethanol. It is a violation of federal law

and will damage the unit and void your war-

ranty.

Fuel system damage or performance problems resulting

from the use of an oxygenated fuel containing more than

the percentage of oxygenates stated below are not covered

under warranty.

Starting and Stopping

See Figures 10 - 11.

To start a cold engine:

1. Set the blower on a at, bare surface.

2. Slowly press the primer bulb 8 times.

Note: After the 8th press, fuel should be visible in the

primer bulb. If it is not, continue to press the primer

until you see fuel in the bulb.

®

Primer Bulb

Stop

Switch

Starter

Grip and

Rope

Figure 10

STOP

Choke

Lever

Throttle

Trigger

B

RUN

HALF

FULL

RUN

HALF

FULL

RUN

HALF

FULL

B

RUN

HALF

FULL

RUN

HALF

FULL

RUN

HALF

FULL

Figure 11

Half

Choke

Full

Choke

Run

Position

B

RUN

HALF

FULL

RUN

HALF

FULL

RUN

HALF

FULL

3. Place the choke lever in the FULL CHOKE position.

4. Pull throttle lock back to lock the throttle wide open.

5. Pull the starter grip and rope sharply until engine at-

tempts to run. Do not pull the starter grip more than

four (4) times.

6. Set the choke lever in the HALF CHOKE position.

7. Pull the starter grip and rope until the engine runs. Do

not pull the starter grip more than six (6) times.

Note: If the engine does not start, return to the FULL

CHOKE position and repeat steps 3 through 6 again.

8. Allow the engine to run for 20 seconds, then place the

choke lever in the RUN position.

Note: In cooler environments, additional pulls of the

starter handle may be required with the choke lever in

the FULL CHOKE position.

To start warm engine:

1. Place the choke lever in the RUN position.

2. Pull throttle lock back to lock the throttle wide open.

3. Pull the starter grip and rope until the engine runs.

Note: If the engine does not start, repeat steps 3

through 7 again.

To stop the engine:

1. Press the stop switch to the stop (

STOP

) position, the

engine will stop. The switch will automatically return to

the on (I) position when released.

16

Proper Operating Position

Figure 12

Sweeper Nozzle

Figure 13

Operating the Blower

See Figures 12 - 13.

WARNING:

Never run the unit without the blower tubes

installed or the vacuum door securely closed.

Failure to follow these steps could result in pos-

sible serious injuries.

WARNING:

Always wear eye protection with side shields

marked to comply with ANSI Z87.1, along with

hearing protection. Failure to do so could result

in objects being thrown into your eyes and other

possible serious injuries.

1. Start the blower. Refer to “Starting and Stopping”

earlier in this manual. Hold the blower with the upper

handle in your right hand.

WARNING:

Always hold the blower away from your body

with the handle in your right hand when operat-

ing as a blower, keeping clearance between your

body and the product. The mufer side of the

blower should be away from your body. Any

contact with the housing can result in burns and/

or other serious personal injury.

Operation

WARNING:

Do not place blower on top of or near loose

debris or gravel. Debris may be sucked into

blower intake vent resulting in possible damage

to the unit and could result in serious personal

injury.

2. To keep from scattering debris, blow around the outer

edges of a debris pile. Never blow directly into the

center of a pile.

3. Operate power equipment at reasonable hours only - not

early in the morning or late at night when people might

be disturbed. Comply with the times listed in local

ordinances.

4. To reduce sound levels, limit the number of pieces of

equipment used at any one time.

5. Conserve water by using power blowers instead of

hoses for many lawn and garden applications, including

areas such as gutters, screens, patios, grills, porches,

and gardens.

6. Operate blower at the lowest possible throttle speed to

do the job.

7. Check your equipment before operation, especially the

mufer, air intakes, and air lters.

8. Use rakes and brooms to loosen debris before blowing.

9. In dusty conditions, slightly dampen surfaces when

water is available.

10. Watch out for children, pets, open windows, or freshly

washed cars, and blow debris safely away.

11. Use the sweeper nozzle so the air stream can work close

to the ground.

12. After using blowers or other equipment, CLEAN UP!

Dispose of debris properly.

13. Use the sweeper nozzle for the everyday blowing op-

eration. This nozzle allows for more area to be covered

during the blowing operation.

17

Operation

Throttle Lock

See Figure 14

The throttle lock can be used to operate the blower without

holding the throttle trigger.

To engage the throttle lock:

1. Pull throttle lock back towards user, and stop at the

desired throttle setting.

2. To release the throttle lock, push throttle lock all the

way towards the front of unit.

Figure 15

Proper Operating Position

Hold Muffler Away From Body And Clothing

®

Figure 14

®

Throttle

Lock

Throttle

Trigger

Vacuum Operation

See Figure 15.

WARNING:

Never run the unit without the vacuum tubes

and vacuum bag installed. Failure to do so could

result in serious personal injury.

WARNING:

Always wear eye protection with side shields

marked to comply with ANSI Z87.1, along with

hearing protection. Failure to do so could result

in objects being thrown into your eyes and other

possible serious injuries.

WARNING:

Keep the mufer and all hot surfaces of the

blower/vacuum away from your body. Failure

to do so could result in possible serious personal

injury.

1. Install the vacuum tubes and bag. Refer to the Assem-

bly section earlier in this manual.

2. Start the engine. Refer to Starting and Stopping earlier

in this manual.

3. Place the vacuum bag strap over your left shoulder.

Hold the upper handle in your right hand and the

vacuum handle in your left hand.

4. Move the vacuum from side to side along outer edge of

the debris. To avoid clogging, do not place the vacuum

tube directly into the debris pile.

5. Hold the engine higher than the inlet end of the vacuum

tube.

6. Always point vacuum tube downhill when working on a

hillside.

7. To avoid injury to the operator or unit, do not pick up

rocks, broken glass, bottles, or other similar objects.

8. If the vacuum tubes should clog, stop the engine and

disconnect the spark plug wire before cleaning out the

obstruction.

9. Remove the vacuum tubes and clear the debris from

the blower fan housing. Remove the bag and clear the

adaptor. A small rod or stick may be required to clear

the entire tube length. Ensure that all debris has been

cleared before reassembling the vacuum tubes.

18

Maintenance

WARNING:

Do not at any time let brake uids, gasoline,

petroleum-based products, penetrating lubricants,

etc., come in contact with plastic parts. Chemi-

cals can damage, weaken or destroy plastic which

can result in serious personal injury.

Cleaning the Product

1.Stop the product before cleaning.

2.Clean the exterior of the product with a damp cloth.

3.Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use.

4.Scrape debris away from air intake vents on both sides

of the motor housing.

NOTICE:

Keeping air intake vents free of grass and debris

prevents motor overheating and possible failure.

Servicing the Product

Check and tighten all fasteners. If any part is damaged or

lost, repair it or replace it.

Checking the Fuel Cap, Tank, and

Lines

WARNING:

Check for fuel leaks. A leaking fuel cap, tank,

or lines are a re hazard and must be replaced

immediately. If you nd any leaks, correct the

problem before using the product. Failure to do

so could result in a re that could cause serious

personal injury.

The fuel cap contains a non-serviceable lter and check

valve. A clogged fuel lter causes poor engine performance.

If performance improves when the fuel cap is loosened,

the check valve may be faulty or the lter may be clogged.

Replace the fuel cap if necessary.

Maintenance

Normal maintenance, replacement or repair of emission con-

trol devices and systems may be performed by any qualied

repair establishment or individual with original or equiva-

lent parts. Warranty and recall repairs must be performed

by an authorized service center; please contact customer

service for assistance

WARNING:

Use only Toro replacement parts when servicing

this product. Use of any other parts could create

a hazard or cause product damage.

WARNING:

Always wear eye protection with side shields

marked to comply with ANSI Z87.1, along with

hearing protection. Failure to do so could result

in objects being thrown into your eyes and other

possible serious injuries.

WARNING:

Before inspecting, cleaning, or servicing the

machine, shut off engine, wait for all moving

parts to stop, and disconnect spark plug wire

and move it away from spark plug. Failure to

follow these instructions can result in serious

personal injury or property damage.

NOTICE:

Periodically inspect the entire product for dam-

aged, missing, or loose parts such as screws,

nuts, bolts, caps, etc. Tighten securely all fasten-

ers and caps and do not operate this product

until all missing or damaged parts are replaced.

Please contact customer service or a qualied

service center for assistance.

General Maintenance

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use

clean cloths to remove dirt, dust, lubricant, grease, etc.

19

Maintenance

Cleaning Air Filter

See Figure 16.

A wet or dirty air lter can affect the way the engine starts,

performs, and wears. The air lter should be checked and

cleaned after 5 hours of operation. Inspect and clean more

frequently if used in dusty dirty conditions.

For best performance, the air lter should be replaced every

25 hours or yearly.

To clean the air filter:

1. Depress air lter cover tab using a straight screwdriver

to open the air lter cover.

2. Remove the cover.

3. Lift the edge of the air lter carefully and peel it out.

4. Wash the air lter with warm, soapy water.

5. Rinse and squeeze to dry.

6. To reinstall the air lter cover, insert the tabs into the

notches and lock into place.

Note: Make sure the lter is seated properly inside the

cover. Installing the lter incorrectly will allow dirt to

enter the engine, causing rapid engine wear.

Air Filter

Cover

Figure 16

Air Filter

CoverTab

Figure 17

Spark

Plug Boot

Spark

Plug

Note: Depending on the type of fuel used, the type and

amount of lubricant used, and/or your operating conditions,

the exhaust port, mufer, and/or spark arrestor screen may

become blocked with carbon deposits. If you notice a power

loss with your gas powered tool, you may need to remove

these deposits to restore performance. We highly recom-

mend that only qualied service technicians perform this

service.

Vacuum Bag

A dirty bag will reduce performance. To clean the bag, turn it

inside out and shake. Wash the bag in soapy water at least once

a year. Replacement parts available online at www.toro.com.

Spark Plug Replacement

See Figure 17.

This engine uses a Champion RCJ6Y spark plug. Use a

recommended or equivalent replacement every 25 hours or

annually.

1. Remove the spark plug boot.

2. Loosen the spark plug by turning it counterclockwise

with a socket.

Cleaning the Exhaust Port, Muffler

and Spark Arrestor

NOTICE:

The spark arrestor on this product has not been

evaluated by the USDA Forest Service and

cannot be used on U.S. forest lands. In addition,

product users must comply with Federal, State,

and local re prevention regulations. Check

with appropriate authorities. Contact customer

service or a qualied service center to purchase

a replacement spark arrestor.

20

Maintenance

This Product Was Manufactured With A Catalyst Muffler

Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s origi-

nal emission level, please refer to the maintenance section below.

MAINTENANCE SCHEDULE

Inspect for Clean Clean or Replace Replace

Maintenance Damage Before Every Every 25 Hours Every

Part Each Use 5 Hours or Yearly 125 Hours

* CATALYTIC MUFFLER ASSEMBLY .................................................................................................................X

* AIR FILTER ASSY

includes:

Filter .......................................................................................X

* CARBURETOR ASSY

includes:

Gaskets .......................................... X

* FUEL TANK ASSY

includes:

Fuel Lines ...................................... X

Fuel Cap ........................................ X

Fuel Filter ...................................................................................................................... X

* IGNITION ASSY

includes:

Spark Plug ..................................................................................................................... X

*NOTICE: THE USE OF EMISSION CONTROL COMPONENTS OTHER THAN THOSE DESIGNED FOR THIS

UNIT IS A VIOLATION OF FEDERAL LAW.

3. Remove the spark plug.

4. Inspect the new spark plug. The spark plug must

be properly gapped and free of deposits in order to

ensure proper engine operation. The correct gap is

approximately 0.025 in. (0.64 mm). To widen gap, if

necessary, carefully bend the ground (top) electrode.

To lessen gap, gently tap ground electrode on a hard

surface.

5. Hand thread the new spark plug into the cylinder , turn-

ing it clockwise.

6. Tighten with a socket. (torque to 216 in.lb. [24.40 Nm]

minimum, 264 in.lb. [29.82 Nm] maximum.) Do not

over-tighten.

NOTICE:

Be careful not to cross-thread the spark plug.

Cross-threading will seriously damage the

product.

Storing the Product

1. Clean all foreign material from the product. Store unit

indoors in a dry, well-ventilated area that is inaccessible

to children. Keep away from corrosive agents such as

garden chemicals, fertilizer, and de-icing salts.

2. Abide by all ISO and local regulations for the safe stor-

age and handling of gasoline.

When storing 1 month or longer:

1. Drain all fuel from tank into a container approved for

gasoline.

2. Run engine until it stops.

3. Place choke lever in the FULL CHOKE position.

4. Pull throttle lock back to lock the throttle.

5. Attempt to start the engine ve (5) more times.

High Altitude Engine Operation:

Your engine is congured for operation below 2000 feet

altitude at the factory. Your engine must be re-congured

for operation above 2000 feet altitude. Operating the engine

with the wrong engine conguration at a given altitude may

increase its emissions, decrease fuel efciency, degrade

performance and cause irreversible damage. Engines

congured for high altitude operation cannot be operated

in standard altitude conditions. A qualied service center

should ensure that your engine is properly congured for

your location.

La page charge ...

Toro Powervac Gas-Powered Blower Manuel utilisateur

Toro Powervac Gas-Powered Blower Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents