Ryobi Blower RY09051 Manuel utilisateur

Marque: Ryobi

Modèle: Blower RY09051

Catégorie: Souffleurs / sécheurs d'air

Taper: Manuel utilisateur

Ce manuel convient également à

RY09051

Your blower/vacuum has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this

product. If you do not understand the warnings and instructions in the operator’s manual, do not use this product.

Cette soufflante / aspirateur a été conçue et fabriquée conformément

à nos strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation. Correctement entretenue, elle vous donnera des

années de fonctionnement robuste et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre

le manuel d’utilisation avant d’employer ce produit. Si tous

les avertissements et toutes les consignes de sécurités et

instructions du manuel d’utilisation ne sont pas bien compris,

ne pas utiliser ce produit.

Su sopladora / aspiradora ha sido diseñada y fabricada de

conformidad con las estrictas normas para brindar fiabilidad,

facilidad de uso y seguridad para el operador. Con el debido cuidado,

le brindará muchos años de sólido y eficiente funcionamiento.

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador antes

de usar este producto. Guarde este manual del operador y

estúdielo frecuentemente para lograr un funcionamiento seguro

y continuo de este producto

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

SAVE THIS MANUAL FOR FUTURE REFERENCE

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

BLOWER / VACUUM

SOUFFLANTE / ASPIRATEUR

SOPLADORA / ASPIRADORA

RY09051

ALL VERSIONS

TOUTES LES VERSIONS

TODAS LAS VERSIONES

Fig. 1

Fig. 2

Fig. 3

Fig. 5

Fig. 6

Fig. 4

A - Lower vacuum tube (tube d’aspiration inférieur, tubo inferior de la

aspiradora)

B - Shoulder strap (bandoulière, correa para el hombro)

C - Cruise control (régulateur de vitesse, control de crucero)

D - Upper vacuum tube (tube d’aspiration supérieur, tubo superior de la

aspiradora)

E - Vacuum tube screw (vis de tube d’aspiration, tornillos de los tubos

de la aspiradora)

F - Vacuum bag (sac à débris, saco de la aspiradora)

G - Throttle trigger (gâchette d’accélérateur, gatillo del acelerador)

A - Upper blower tube (tube de soufflante

supérieur, tubo superior de la sopladora)

B - High velocity nozzle with wet leaf scraper

(embout haute vélocité débit avec racloir

à feuilles, boquilla de alta velocidad con

raspador para hojas húmedas)

C - Sweeper nozzle (embout éventail, boquilla

para barrer)

A - Sweeper nozzle (embout éventail, boquilla

para barrer )

B - Upper blower tube (tube de soufflante

supérieur, tubo superior de la sopladora)

C - Blower housing outlet (sortie du logement

de la soufflante,salida del armazón de la

sopladora)

A - Adaptor installed in vacuum bag (adaptateur

installé dans le sac à débris, adaptador

instalado en el saco de la aspiradora)

B - Raised slot (fente en saillie, ranura realzada)

C - Raised locking tab (languette de

verrouillage en saillie, orejeta realzada de

aseguramiento)

A - Vacuum bag assembly (ensemble de sac à

débris, conjunto del saco de la aspiradora)

B - Vacuum inlet door (volet d’entrée d’air,

puerta de la entrada de la aspiradora)

C - Door tab (languette du volet, orejeta de la

puerta)

A - Adaptor (adaptateur, adaptador)

B - Vacuum bag (sac à débris, saco de la

aspiradora)

H - Stop switch (commutateur d’arrêt, interruptor del apagado)

I - Vacuum handle (poignée d’aspirateur , mango de la aspiradora )

J - Fuel cap (bouchon du réservoir, tapa del tanque de combustible)

K - Starter grip and rope (poignée du lanceur, mango del arrancador)

L - Primer bulb (poire d’amorçage, bomba de cebado)

M - Choke lever (levier de volet de départ, palanca del anegador)

N - Upper handle (poignée supérieure, mango superior)

O - Vacuum bag adaptor (adaptateur de sac, adaptador del saco)

P - Muffler (silencieux, silenciador)

Q - Raised slot (fente en saillie, ranura realzada)

See this fold-out section for all the figures referenced in the operator’s manual.

Voir que cette section d’encart pour toutes les figures a adressé dans le manuel d’utilisation.

Vea esta sección de la página desplegable para todas las figuras mencionó

en el manual del operador.

Fig. 7

Fig. 9

Fig. 12

Fig. 13

Fig. 14

Fig. 10

Fig. 11

Fig. 8

A - Vacuum tube assembly (ensemble de tubes

d’aspiration, conjunto de los tubos de la

aspiradora)

B - Vacuum inlet door (volet d’entrée d’air,

puerta de la entrada de la aspiradora)

C - Screw (vis, tornillo)

D - Vacuum opening (ouverture d’aspiration,

abertura de aspiración)

E - Screw mounts (trous de vis, agujeros de

tornillos)

A - Stop switch (commutateur d’arrêt,

interruptor del apagado)

B - Throttle trigger (gâchette d’accélérateur,

gatillo del acelerador)

C - Choke lever (levier de volet de départ,

palanca del anegador)

D - Primer bulb (poire d’amorçage, bomba de

cebado)

E - Starter grip with rope (poignée du lanceur,

mango del arrancador)

A - Sweeper nozzle (embout éventail, boquilla

para barrer)

B - High velocity nozzle (embout haute vélocité,

boquilla de alta velocidad)

A - Turn the dial to open and close (tourner

le cadran pour ouvrir et fermeture, gire el

selector para abrirla y cerrar )

B - Air filter cover (couvercle du filtre à air, tapa

de la cámara de ventilación)

A - Air filter cover (couvercle du filtre à air, tapa

de la cámara de ventilación)

B - Air filter (filtre à air, filtro de aire)

A - Cruise control (régulateur de vitesse,

control de crucero)

B - Throttle trigger (gâchette d’accélérateur,

gatillo del acelerador)

PROPER BLOWER OPERATING POSITION

POSITION D’UTILISATION ADÉQUATE DE LA

SOUFFLANTE

POSICIÓN DE FUNCIONAMIENTO CORRECTA

DE LA SOPLADORA

PROPER VACUUM OPERATING POSITION

POSITION D’UTILISATION ADÉQUATE DE

L’ASPIRATEUR

POSICIÓN DE FUNCIONAMIENTO CORRECTA

DE LA ASPIRADORA

Keep muffler away from the body (garder les

mains à l’écart des silencieux, mantenga las

manos alejadas de las silenciador)

2 - English

INTRODUCTION

INTRODUCTION / INTRODUCCIÓN

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product making it easy to maintain and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la

conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à

utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto

se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.

 Introduction ......................................................................................................................................................................2

Introduction / Introducción

 General Safety Rules ........................................................................................................................................................ 3

Règles de sécurité générales / Reglas de seguridad generales

 Specific Safety Rules ........................................................................................................................................................4

Règles de sécurité particulières / Reglas de seguridad específicas

 Symbols ............................................................................................................................................................................5

Symboles / Símbolos

 Features ............................................................................................................................................................................6

Caractéristiques / Características

 Assembly .......................................................................................................................................................................6-7

Assemblage / Armado

 Operation ..................................................................................................................................................................... 8-10

Utilisation / Funcionamiento

 Maintenance ..............................................................................................................................................................10-11

Entretien / Mantenimiento

 Troubleshooting .............................................................................................................................................................. 11

Dépannage / Solución de problemas

 Warranty ....................................................................................................................................................................12-14

Garantie / Garantía

 Parts Ordering and Service ...............................................................................................................................Back Page

Commande de pièces et réparation / Pedidos de piezas y servicio ......................................................... Page arrière / Pág. posterior

TABLE OF CONTENTS

TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO

3 - English

GENERAL SAFETY RULES

WARNING:

READ AND UNDERSTAND ALL INSTRUCTIONS. Fail-

ure to follow all instructions listed below may result in

electric shock, fire and/or serious personal injury.

READ ALL INSTRUCTIONS

Do not allow children or untrained individuals to use this

unit.

Never start or run the engine inside a closed area;

breathing exhaust fumes can kill.

Wear eye protection with side shields which is marked

to comply with ANSI Z87.1 along with hearing protection

when operating this product.

Keep all bystanders, children, and pets at least 50 ft.

away.

Wear heavy long pants, long sleeves, boots, and gloves.

Do not wear loose fitting clothing, short pants, sandals,

jewelry of any kind, or go barefoot.

To reduce the risk of injury associated with objects being

drawn into rotating parts, do not wear loose clothing,

scarves, neck chains, etc.

Secure long hair so it is above shoulder level to prevent

entanglement in any rotating parts.

Do not operate this unit when you are tired, ill, or under

the influence of alcohol, drugs, or medication.

Do not operate in poor lighting.

Keep all parts of your body away from any moving parts

and all hot surfaces of the unit.

Wear a face filter mask in dusty conditions to reduce the

risk of injury associated with the inhalation of dust.

Check the work area before each use. Remove all objects

such as rocks, broken glass, nails, wire, or string which

can be thrown or become entangled in the machine.

Keep firm footing and balance. Do not overreach.

Overreaching can result in loss of balance or exposure

to hot surfaces.

Never operate the unit without a spark arrestor screen;

this screen is located inside the muffler.

Product users on United States Forest Service land,

and in some states, must comply with fire prevention

regulations. This product is equipped with a spark

arrestor; however, other user requirements may apply.

Check with the federal, state, or local authorities in your

area.

Before storing, allow the engine to cool.

Empty fuel tank into a container approved for gasoline

and restrain the unit from moving before transporting in

a vehicle.

To reduce the risk of fire and burn injury, handle fuel with

care. It is highly flammable.

Do not smoke while handling fuel.

Mix and store fuel in a container approved for gasoline.

Mix fuel outdoors where there are no sparks or flames.

Select bare ground, stop engine, and allow to cool before

refueling.

Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.

Tighten the fuel cap securely after refueling.

Wipe spilled fuel from the unit. Move 30 ft. away from

refueling site before starting engine.

Never attempt to burn off spilled fuel under any

circumstances.

Use only identical manufacturer’s replacement parts and

accessories. Use of any other parts may create a hazard

or cause product damage.

Maintain the unit per maintenance instructions in this

Operator’s Manual.

Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace damaged parts.

Do not use on a ladder, rooftop, tree, or other unstable

support. Stable footing on a solid surface enables better

control of the blower in unexpected situations.



Before cleaning, repairing, or inspecting, shut off the

engine and make certain all moving parts have stopped.

Disconnect the spark plug wire, and keep the wire away

from the plug to prevent starting.



Service on the blower/vacuum must be performed by

qualified repair personnel only. Service or maintenance

performed by unqualified personnel could result in injury

to the user or damage to the product.

4 - English

Always hold the blower/vacuum in your right hand during

blower operation. Refer to the OPERATION instructions

later in this manual for proper position during vacuum

operation and additional information.

Never place objects inside the blower tubes.

Use only as directed in this operator’s manual.

Do not operate vacuum without vacuum bag installed;

flying debris could cause serious injury. Always close

vacuum bag completely before operating.

Rotating impeller blades can cause severe injury. Stop the

engine and ensure impeller blades have stopped rotating

before opening the vacuum door or installing/ changing

tubes. Do not put hands or any other object into the

vacuum tubes while they are installed on the unit.

 Never run the unit without the proper equipment attached.

When used as a blower, always install the blower tubes.

When used as a vacuum, always install the vacuum

tubes and vacuum bag. Make sure the vacuum bag is

completely zipped when the unit is running to avoid flying

debris.

 Avoid situations that could catch the vacuum bag on

fire. Do not operate near an open flame. Do not vacuum

warm ash from fireplaces, barbecue pits, brush piles, etc.

Do not vacuum discarded cigars or cigarettes unless the

cinders are completely cool.

 Never place blower on any surface, except a hard, clean

surface when engine is running. Gravel, sand, and other

debris can be picked up by the air inlet and thrown at

the operator or bystanders, causing possible serious

injuries.

 To reduce the risk of hearing loss associated with sound

level(s), hearing protection is required.

 To reduce the risk of injury associated with contacting

rotating parts, stop the engine before installing or

removing attachments. Always disconnect the spark plug

before performing maintenance or accessing any movable

parts.

 Never use blower near fires, fireplaces, hot ashes,

barbecue pits, etc., which may cause fire to spread.

 Do not point the blower nozzle in the direction of people

or pets.

 Never run the unit without the proper equipment attached.

Always ensure the blower tubes are installed.

SPECIFIC SAFETY RULES

FUELING

 Fuel is highly flammable. Take precautions when using

to reduce the chance of serious personal injury.

 Store fuel in a cool, well-ventilated area, safely away from

spark and/or flame-producing equipment.

 Store fuel in containers specifically designed for this

purpose.

 Only refuel outdoors and do not smoke while refueling.

 Add fuel before starting the engine. Never remove the cap

of the fuel tank or add fuel while the engine is running or

when the engine is hot.

 Do not smoke while handling fuel.

 Mix and store fuel in a container approved for gasoline.

 Mix fuel outdoors where there are no sparks or flames.

 Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.

 Tighten the fuel cap securely after refueling.

 Wipe spilled fuel from the unit. Move 30 feet away from

refueling site before starting engine.

 Never attempt to burn off spilled fuel under any circum-

stances.

 To reduce the risk of fire and burn injury, handle fuel with

care. It is highly flammable.

 If fuel is spilled, do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until fuel vapors

have dissipated.

 Replace all fuel tank and container caps securely.

 Empty fuel tank into a container approved for gasoline

and restrain the unit from moving before transporting in

a vehicle.

 When draining the fuel tank, use an approved fuel storage

container in a well-ventilated area.

 Select bare ground, stop engine, and allow to cool before

refueling.

 Save these instructions. Refer to them frequently and use

them to instruct others who may use this tool. If you loan

someone this tool, loan them these instructions also.

5 - English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME EXPLANATION

Safety Alert Symbol Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Wear Eye and Hearing Protection

Always wear eye protection with side shields marked to

comply with ANSI Z87.1 as well as hearing protection when

operating this equipment.

Vacuum Door Do not run unit while vacuum door is unsecured.

Long Hair Risk of long hair being drawn into air inlet.

Blower Tubes Do run unit without tubes in place.

Loose Clothing Risk of loose clothing being drawn into air intake.

Gasoline and Lubricant

Use unleaded gasoline intended for motor vehicle use with

an octane rating of 87 [(R + M) / 2] or higher. This product is

and 2-cycle lubricant.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

CAUTION:

(Without Safety Alert Symbol) Indicates a situation that may result in property

damage.

6 - English

FEATURES

PRODUCT SPECIFICATIONS

Engine Displacement.......................................................................................................................................................26cc

Air Velocity:

MPH ..................................................................................................................................200 (with high velocity nozzle)

CFM ........................................................................................................................................................400 (at housing)

Weight .........................................................................................................................................................................9.5 lbs.

KNOW YOUR BLOWER/VACUUM

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

BLOWER TUBE AND NOZZLES

The blower tube can be assembled and installed on the

blower without using any tools.

CRUISE CONTROL

The cruise control feature allows the user to operate the

blower without holding the throttle trigger. To slow the engine,

simply push the cruise control lever forward.

ENGINE

The blower has a powerful 26cc engine with sufficient power

to handle tough blowing and vacuuming jobs.

HIGH VELOCITY NOZZLE WITH WET LEAF

SCRAPER

The high velocity nozzle is great for wet sticky leaves. It

allows you to scrape wet leaves or debris while operating

the blower.

SWEEPER NOZZLE

The sweeper nozzle allows for more area to be covered

during blower operation.

THROTTLE TRIGGER

The blower can be operated at any speed between idle and

full throttle.

VACUUM / MULCHER

Converting the blower to a vacuum/mulcher is simple and

can be done using a flat head screwdriver.

VACUUM BAG

The vacuum bag attaches to the blower easily by using the

vacuum bag adaptor.

VACUUM HANDLE

This feature allows user to perform vacuuming duties

comfortably.

VACUUM TUBES

The vacuum tubes can be installed on the blower using a

flat head screw driver.

UNPACKING

This product requires assembly.



Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

WARNING:

Do not use this product if any parts on the Packing List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.



Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

ASSEMBLY



Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the product.



If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

PACKING LIST

Blower

Upper Blower Tube

Sweeper Nozzle

High Velocity Nozzle

Upper and Lower Vacuum Tubes

Vacuum Tube Screws (2)

Vacuum Bag

Vacuum Bag Adaptor

2-Cycle Engine Lubricant

Operator’s Manual

NOTE: Read and remove all hang tags and store with your

operator’s manual.

7 - English

ASSEMBLY

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of the product

with damaged or missing parts could result in possible

serious personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

To prevent accidental starting that could cause serious

personal injury, always disconnect the engine spark plug

wire from the spark plug when assembling parts.

ASSEMBLING THE BLOWER TUBES

See Figures 2 - 3.



Align raised tabs on blower housing outlet to the slots

on upper tube; slide together and tighten securely by

twisting. Check tightness after initial use and retighten if

needed.



Attach desired nozzle (high velocity nozzle or sweeper

nozzle) to upper blower tube by aligning raised tabs on

upper blower tube; slide together and tighten securely by

twisting. Check tightness after initial use and retighten if

needed.



To remove the tubes, rotate the tubes to unlock them and

remove from the blower housing outlet.

INSTALLING THE VACUUM BAG

See Figures 3 - 5.



Remove the nozzle and upper blower tube from the

blower by twisting and removing from blower housing

outlet.



Unzip the vacuum bag and place the vacuum bag adaptor

inside as shown. Push the vacuum bag adaptor through

the opening opposite the zipper. The wider end of the

adaptor will remain on the inside of the vacuum bag when

installed properly.



Align the raised slots on the vacuum bag adaptor with the

raised locking tabs on the blower housing outlet; push

the vacuum bag adaptor onto the housing. Twist to lock

into place.



Rotate the vacuum bag until the shoulder strap is upright.



Make sure the vacuum bag is zipped and closed before

starting the unit.

INSTALLING THE VACUUM TUBES

See Figures 6 - 7.

WARNING:

Contact with rotating impeller blades could result in seri-

ous personal injury. Always stop the engine and ensure

impeller blades have stopped rotating before opening

the vacuum door or installing/changing tubes. Do not put

hands or any other object into the vacuum tubes while

they are installed on the unit.

To install the vacuum tubes:



Secure the upper and lower vacuum tubes together by

aligning the raised locking tabs with the raised slots.



Tap tube assembly on ground until the screw holes in

lower tube are in the raised slot of the upper tube. Secure

with supplied screws.



Depress door tab using a flathead screwdriver and open

vacuum inlet door.



Align screw mounts on vacuum opening with screws on

vacuum tube assembly.



Turning clockwise, tighten screws on upper vacuum tube

to secure to blower housing.

To remove the vacuum tubes:



Loosen screws of the upper vacuum tube by turning

counterclockwise.



Remove the vacuum tube assembly from the blower

housing.



Close the vacuum inlet cover door securely.

8 - English

2-CYCLE FUEL / OIL MIX (50:1)

GASOLINE OIL

1 gallon (US) 2.6 oz.

1 liter 20 cc (20 ml)

OPERATION

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

APPLICATIONS

You may use this product for the purposes listed below:



Clearing leaves and other debris from your lawn



Keeping decks and driveways free from leaves and pine

needles



Vacuuming leaves from your lawn

MIXING THE FUEL

This product is powered by a 2-cycle engine and requires

premixing gasoline and 2-cycle oil. The mixture should be

at a 50:1 ratio.

NOTE: We recommend you use ONLY Ryobi (exact mix)

your product.

To mix the fuel:



Use a clean container that is approved for use with gaso-

line.



Mix the 2-cycle engine oil with unleaded gasoline in the

container, according to the instructions on the oil pack-

age.

This engine is certified to operate on unleaded gasoline

intended for automotive use with an octane rating of 87

[(R + M) / 2] or higher. Do not use automotive oil or 2-cycle

outboard oil.

NOTE: Most fuel mixture will stay fresh up to 30 days. DO

NOT mix quantities larger than usable in a 30 day period.

FILLING THE TANK



Clean the surface around the fuel cap to prevent con-

tamination.



Loosen the fuel cap slowly by turning counterclock-

wise.



Pour the fuel mixture carefully into the tank.



Clean and inspect the fuel cap gasket before replacing

the fuel cap.



Replace the fuel cap and tighten it by turning it clock-

wise.



Wipe spilled fuel from the product.



Move at least 30 ft. away from refueling area before start-

ing the product.

NOTE: It is normal for smoke to be emitted from a new

engine during first use.

WARNING:

Always shut off engine before fueling. Never add fuel to

a machine with a running or hot engine. Move at least

30 ft. from refueling site before starting engine. Do not

smoke and stay away from open flames and sparks.

Failure to safely handle fuel could result in serious per-

sonal injury.

OXYGENATED FUELS

DO NOT USE E85 FUEL. IT WILL VOID YOUR

WARRANTY.

NOTE: Fuel system damage or performance problems

resulting from the use of an oxygenated fuel containing more

than the percentages of oxygenates stated previously are

not covered under warranty.

Ethanol. Gasoline containing up to 10% ethanol by

volume (commonly referred to as E10) or 15% ethanol by

volume (commonly referred to as E15) are acceptable.

Do not use E85 fuel.

STARTING AND STOPPING

See Figure 8.

Blower should be on a flat, bare surface for starting.

 Slowly press the primer bulb 10 times.

NOTE: After the 10th press, fuel should be visible in the

primer bulb. If it is not, continue to press the primer until

you see fuel in the bulb.

 Set the choke lever to the FULL CHOKE position.

 Lock throttle lever.

 Pull starter grip and rope sharply until engine attempts

to run. Do not pull the starter grip more than four (4)

times.

 Set the choke lever to the HALF CHOKE position.

 Pull the starter grip and rope until the engine runs.

NOTE: If the engine does not start, return to the FULL

CHOKE position and repeat the steps that follow.

 Allow the engine to run for 10 seconds, then set the choke

lever to the RUN position.

9 - English

OPERATION

TO STOP THE ENGINE:

 To stop the engine, depress and hold the STOP switch

to the stop position “ ”.

HOT RESTART OF THE ENGINE:

 Set the choke lever to the RUN position.

 Lock throttle lever.

 Pull the starter grip and rope until the engine runs.

IF ASSISTANCE IS REQUIRED STARTING

THIS PRODUCT:

Do not return this product to the retail store where it was

purchased. Please call our Customer Service Department

for any issues you may have.

For Help Call: 1-800-860-4050

OPERATING THE BLOWER

See Figures 9 - 10.

WARNING:

Never run the unit without the blower tubes installed or

the vacuum door securely closed. Use of an improperly

assembled unit could result in serious personal injury.



Start the blower. Refer to Starting and Stopping earlier

in this manual. Hold the blower with the upper handle in

your right hand.

WARNING:

Always hold the blower away from your body with the

handle in your right hand when operating as a blower,

keeping clearance between your body and the product.

The muffler side of the blower should be away from your

body. Any contact with the housing can result in burns

and/or other serious personal injury.

WARNING:

Do not place blower on top of or near loose debris or

gravel. Debris may be sucked into blower intake vent

resulting in possible damage to the unit and could result

in serious personal injury.



To keep from scattering debris, blow around the outer

edges of a debris pile. Never blow directly into the center

of a pile.



Operate power equipment at reasonable hours only - not

early in the morning or late at night when people might

be disturbed. Comply with the times listed in local ordi-

nances.



To reduce sound levels, limit the number of pieces of

equipment used at any one time.



Conserve water by using power blowers instead of hoses

for many lawn and garden applications, including areas

such as gutters, screens, patios, grills, porches, and

gardens.



Operate blower at the lowest possible throttle speed to

do the job.



Check your equipment before operation, especially the

muffler, air intakes, and air filters.



Use rakes and brooms to loosen debris before blowing.



In dusty conditions, slightly dampen surfaces when water

is available.



Watch out for children, pets, open windows, or freshly

washed cars, and blow debris safely away.



Hold blower, as shown in Figure 9, so the air stream can

work close to the ground.



After using blowers or other equipment, CLEAN UP!

Dispose of debris properly.



Use the sweeper nozzle for the everyday blowing opera-

tion. This nozzle allows for more area to be covered during

the blowing operation.



The high velocity nozzle is specifically designed for wet

sticky leaves. It allows you to scrape wet leaves or debris

while operating the blower.

CRUISE CONTROL

See Figure 11.

The cruise control can be used to operate the blower without

holding the throttle trigger.

To engage the cruise control:



Pull cruise control lever back towards user, and stop at

the desired throttle setting.



To release the cruise control, push cruise control lever

all the way towards the front of unit.

VACUUM OPERATION

See Figure 12.

WARNING:

Never run the unit without the vacuum tubes and vacuum

bag installed. Use of an improperly assembled unit could

result in serious personal injury.

WARNING:

Keep the muffler and all hot surfaces of the blower/

vacuum away from your body. Failure to do so could

result in possible serious personal injury.



Install the vacuum tubes and the bag. Refer to the

ASSEMBLY section earlier in this manual.



Start the blower. Refer to Starting and Stopping earlier

in this manual.

10 - English

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

WARNING:

Before inspecting, cleaning, or servicing the machine,

shut off engine, wait for all moving parts to stop, and

disconnect spark plug wire and move it away from spark

plug. Failure to follow these instructions can result in

serious personal injury or property damage.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use

clean cloths to remove dirt, dust, lubricant, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating lubricants, etc., come in con-

tact with plastic parts. Chemicals can damage, weaken or

destroy plastic which may result in serious personal

injury.

OPERATION



Place the vacuum bag strap over your right shoulder.

Hold the upper handle in your left hand and the vacuum

handle in your right hand.



Move the blower/vacuum from side to side along outer

edge of the debris. To avoid clogging, do not place the

vacuum tube directly into the debris pile.



Hold the engine higher than the inlet end of the vacuum

tube.



Always point vacuum tube downhill when working on a

hillside.



To avoid serious injury to the operator or damage to the

unit, do not pick up rocks, metal, broken glass, bottles,

or other similar objects.



If the vacuum tubes should clog, stop the engine , ensure

impeller blades have stopped spinning, and disconnect

the spark plug wire before cleaning out the obstruction.



Remove the vacuum tubes and clear the debris from the

blower fan housing. Remove the bag and clear the tube.

A small rod or stick may be required to clear the entire

tube length. Ensure that all debris has been cleared before

reassembling the vacuum tubes.

MAINTENANCE

You can often make adjustments and repairs described here.

For other repairs, have the blower/vacuum serviced by an

authorized service dealer.

CLEANING THE AIR FILTER

See Figure 13 - 14.

For proper performance and long life, keep air filter clean.

 Remove the air filter cover by turning the dial counter-

clockwise while gently pulling on the cover.

 Rinse filter with clean water.

 Gently squeeze filter until excess water is removed.

Replace filter.

 Place the air filter cover back on the unit. Turn dial clock-

wise until cover is secure.

CLEANING THE EXHAUST PORT, MUFFLER

AND SPARK ARRESTOR

NOTE: Depending on the type of fuel used, the type and

amount of lubricant used, and/or your operating conditions, the

exhaust port, muffler, and/or spark arrestor screen may be-

come blocked with carbon deposits. If you notice a power

loss with your gas powered tool, you may need to remove

these deposits to restore performance. We highly recom-

mend that only qualified service technicians perform this

service.

The spark arrestor must be cleaned or replaced every 50

hours or yearly to ensure proper performance of your prod-

uct. Spark arrestors may be in different locations depending

on the model purchased. Please contact your nearest service

dealer for the location of the spark arrestor for your model.

WARNING:

Never run the blower without the spark arrestor in place.

Failure to do so could result in a fire that could cause

serious personal injury.

11 - English

MAINTENANCE

VACUUM BAG

A dirty bag will reduce performance. To clean the bag, turn it

inside out and shake. Wash the bag in soapy water at least

once a year. To obtain a replacement bag, see How to Order

Replacement Parts on the back page of this manual.

FUEL CAP

WARNING:

Check for fuel leaks. A leaking fuel cap is a fire hazard

and must be replaced immediately. If you find any leaks,

correct the problem before using the product. Failure

to do so could result in a fire that could cause serious

personal injury.

The fuel cap contains a non-serviceable filter and a

check valve. A clogged fuel filter will cause poor engine

performance. If performance improves when the fuel cap

is loosened, check valve may be faulty or filter clogged.

Replace fuel cap if required.

SPARK PLUG REPLACEMENT

This engine uses a Ryobi AC00160, Champion RCJ-6Y or

NGK BPMR7A spark plug with .025 in. electrode gap. Use

an exact replacement and replace annually.

STORING THE PRODUCT

 Clean all foreign material from the product. Store idle unit

indoors in a dry, well-ventilated area that is inaccessible

to children. Keep away from corrosive agents such as

garden chemicals and de-icing salts.

 Abide by all ISO and local regulations for the safe storage

and handling of gasoline.

When storing 1 month or longer:

 Drain all fuel from tank into a container approved for

gasoline. Run engine until it stops.

TROUBLESHOOTING

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM, CONTACT YOUR AUTHORIZED SERVICING DEALER.

PROBLEM CAUSE REMEDY

Engine fails to start. No fuel in tank.

Spark plug shorted or fouled.

Spark plug is broken. (cracked

porcelain or electrodes broken)

Ignition lead wire shorted, broken, or

disconnected from spark plug.

Ignition inoperative.

Fill tank.

Replace spark plug.

Replace lead wire or attach to spark

plug.

Contact authorized service center.

Engine hard to start. Water in gasoline or stale fuel mixture.

Too much lubricant in fuel mixture.

Engine is under or over choked.

Weak spark at spark plug.

Drain entire system and refill with fresh

fuel.

Drain and refill with correct mixture.

Adjust choke as necessary.

Contact authorized service center.

Engine lacks power. Air filter clogged. Clean air filter. Refer to Cleaning the

Air Filter Screen earlier in this manual.

Engine overheats. Insufficient lubricant in fuel mixture. Mix fuel as described in starting

instructions.

12 - English

WARRANTY

LIMITED WARRANTY STATEMENT

Techtronic Industries North America, Inc., warrants to the

original retail purchaser that this RYOBI® brand outdoor

product is free from defect in material and workmanship

and agrees to repair or replace, at Techtronic Industries

North America, Inc.’s, discretion, any defective product

free of charge within these time periods from the date of

purchase.

 Three years if the product is used for personal, family

or household use;

 90 days, if used for any other purpose, such as

commercial or rental.

This warranty extends to the original retail purchaser

only and commences on the date of the original retail

purchase.

Any part of this product found in the reasonable judgment

of Techtronic Industries North America, Inc. to be defective

in material or workmanship will be repaired or replaced

without charge for parts and labor by an authorized service

center for RYOBI® brand outdoor products (Authorized

Ryobi Service Center).

The product, including any defective part, must be returned

to an authorized Ryobi service center within the warranty

period. The expense of delivering the product to the service

center for warranty work and the expense of returning it

back to the owner after repair or replacement will be paid

by the owner. Techtronic Industries North America, Inc.’s,

responsibility in respect to claims is limited to making the

required repairs or replacements and no claim of breach of

warranty shall be cause for cancellation or rescission of the

contract of sale of any RYOBI® brand outdoor product. Proof

of purchase will be required by the dealer to substantiate

any warranty claim. All warranty work must be performed

by an authorized service dealer.

This warranty is limited to ninety (90) days from the date

of original retail purchase for any RYOBI® brand outdoor

product that is used for rental or commercial purposes, or

any other income-producing purpose.

This warranty does not cover any product that has been

subject to misuse, neglect, negligence, or accident, or that

has been operated in any way contrary to the operating

instructions as specified in this operator’s manual. This

warranty does not apply to any damage to the product that

is the result of improper maintenance or to any product

that has been altered or modified. The warranty does not

extend to repairs made necessary by normal wear or by the

use of parts or accessories which are either incompatible

with the RYOBI® brand outdoor product or adversely affect

its operation, performance, or durability. In addition, this

warranty does not cover:

A. Tune-ups – Spark Plugs, Carburetor, Carburetor

Adjustments, Ignition, Filters

B. Wear items – Bump Knobs, Outer Spools, Cutting

Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive

Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades,

Blower Fans, Blower and Vacuum Tubes, Vacuum Bag

and Straps, Guide Bars, Saw Chains

Techtronic Industries North America, Inc., reserves the

right to change or improve the design of any RYOBI® brand

outdoor product without assuming any obligation to modify

any product previously manufactured.

ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION

TO THE STATED WARRANTY PERIOD. ACCORDINGLY,

ANY SUCH IMPLIED WARRANTIES INCLUDING

MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR OTHERWISE, ARE DISCLAIMED IN

THEIR ENTIRETY AFTER THE EXPIRATION OF THE

APPROPRIATE TWO-YEAR, ONE-YEAR, OR NINETY-

DAY WARRANTY PERIOD. TECHTRONIC INDUSTRIES

NORTH AMERICA, INC.’S, OBLIGATION UNDER THIS

WARRANTY IS STRICTLY AND EXCLUSIVELY LIMITED TO

THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS

AND TECHTRONIC INDUSTRIES NORTH AMERICA,

INC., DOES NOT ASSUME OR AUTHORIZE ANYONE

TO ASSUME FOR THEM ANY OTHER OBLIGATION.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW

LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE

LIMITATION MAY NOT APPLY TO YOU. TECHTRONIC

INDUSTRIES NORTH AMERICA, INC., ASSUMES NO

RESPONSIBILITY FOR INCIDENTAL, CONSEQUENTIAL,

OR OTHER DAMAGES INCLUDING, BUT NOT LIMITED

TO, EXPENSE OF RETURNING THE PRODUCT TO AN

AUTHORIZED RYOBI SERVICE CENTER AND EXPENSE

OF DELIVERING IT BACK TO THE OWNER, MECHANIC’S

TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES,

RENTAL OF A LIKE PRODUCT DURING THE TIME

WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,

LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS

OF REVENUE, LOSS OF USE OF THE PRODUCT,

LOSS OF TIME, OR INCONVENIENCE. SOME STATES

DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE

ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY

TO YOU.

This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

This warranty applies to all RYOBI® brand outdoor products

manufactured by or for Techtronic Industries North America,

Inc., and sold in the United States and Canada.

To locate your nearest Authorized Ryobi Service Center,

dial 1-800-860-4050.

13 - English

WARRANTY

THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES TO MODEL NUM-

BERS REQUIRED TO MEET THE CARB REQUIREMENTS.

The U.S. Environmental Protection Agency (EPA), the California Air Resources Board

(CARB), and Techtronic Industries North America, Inc., are pleased to explain the

Emissions Control System Warranty on your 2010 model year non-road or small off-

road engine. In California, new equipment that uses small off-road engines must be

designed, built, and equipped to meet the state’s stringent anti-smog standards. In

other states, new 2000 and later model year non-road engines must be designed,

built, and equipped at the time of sale to meet the U.S. EPA regulations for small

non-road engines. The non-road engine must be free from defects in materials and

workmanship which cause it to fail to conform with U.S. EPA standards for the first

three years of engine use from the date of sale to the ultimate purchaser. Techtronic

Industries North America, Inc., must warrant the emission control system on your

non-road or small off-road engine for the period of time listed above provided there

has been no abuse, neglect, or improper maintenance of your non-road or small

off-road engine.

Your emission control system may include parts such as the carburetor or fuel injection

system, the ignition system, catalytic converters, fuel tanks, valves, filters, clamps,

connectors, and other associated components. Also included may be hoses, belts

and connectors, and other emission-related assemblies.

Where a warrantable condition exists, Techtronic Industries North America, Inc., will

repair your non-road or small off-road engine at no cost to you, including diagno-

sis, parts, and labor performed at an authorized service center for RYOBI® brand

outdoor products.

MANUFACTURER’S WARRANTY COVERAGE:

This product’s emissions control system is warranted for three years. If any emission-

related part on your engine is defective, the part will be repaired or replaced by

Techtronic Industries North America, Inc., free of charge.

OWNER’S WARRANTY RESPONSIBILITIES

(a) As the non-road or small off-road engine owner, you are responsible for

the performance of the required maintenance listed in your operator’s manual.

Techtronic Industries North America, Inc., recommends that you retain all re-

ceipts covering maintenance on your non-road or small off-road engine, but

Techtronic Industries North America, Inc., cannot deny warranty solely for the

lack of receipts or for your failure to ensure the performance of all scheduled

maintenance. Any replacement part or service that is equivalent in performance

and durability may be used in non-warranty maintenance or repairs, and shall

not reduce the warranty obligations of Techtronic Industries North America, Inc.

(b) As the non-road or small off-road engine owner, you should be aware, however,

that Techtronic Industries North America, Inc., may deny you warranty coverage if

your non-road or small off-road engine or a part has failed due to abuse, neglect,

improper maintenance, or unapproved modifications.

authorized service dealer as soon as a problem exists. The warranty repairs should

be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you

should contact a Techtronic Industries North America, Inc., Customer Representa-

tive at 1-800-860-4050.

DEFECT WARRANTY COVERAGE REQUIREMENTS:

(a) The warranty period begins on the date the engine or equipment is delivered to

an ultimate purchaser.

(b) General Emissions Warranty Coverage. Techtronic Industries North America,

Inc., warrants to the ultimate purchaser and each subsequent purchaser that your

non-road or small off-road engine is designed, built, and equipped at the time of sale

to conform with all applicable regulations adopted by the California Air Resources

Board or the United States Environmental Protection Agency; and that it is free from

defects in materials and workmanship which cause the engine to fail to conform with

applicable regulations for a period of three years from the date the non-road or small

off-road engine is purchased by the initial purchaser.

warranted part that is not scheduled for replacement as required in the Emissions

Maintenance Schedule and Warranty Parts List set forth below is warranted for three

years. If any such part (including any part that is scheduled only for regular inspection)

fails during the period of warranty coverage, it will be repaired or replaced at any

RYOBI® Authorized Service Center at no charge. Any such part repaired or replaced

under warranty will be warranted for the remaining warranty period. A statement to

the effect of “repair or replace as necessary” would not reduce the period of war-

ranty coverage. Any warranted part that is scheduled for replacement as required

maintenance in the Emissions Maintenance Schedule and Warranty Parts List is

warranted for the period of time prior to the first scheduled replacement point for

that part. Any such part repaired or replaced under warranty is warranted for the

remainder of the period prior to the first scheduled replacement point, and will be

repaired or replaced at any RYOBI® Authorized Service Center for no charge until

that replacement point is reached.

Techtronic Industries North America, Inc., shall remedy warranty defects at any

authorized RYOBI® Authorized Service Center, including any distribution center

that may be franchised to service the subject engines. Any diagnostic work done

at a RYOBI® Authorized Service Center shall be free of charge to the owner if such

work determines that a warranted part is defective. Any manufacturer-approved or

equivalent replacement part may be used for any warranty maintenance or repairs

on emission-related parts, and must be provided free of charge to the owner if the

part is still under warranty. Techtronic Industries North America, Inc., is liable for

damages to other engine components caused by the failure of a warranted part

still under warranty.

Add-on or modified parts that are not exempted by the California Air Resource Board

may not be used. The use of any non-exempted add-on or modified parts will be

grounds for disallowing a warranty claim. Techtronic Industries North America, Inc.,

will not be liable to warrant failures of warranted parts caused by the use of a non-

exempted add-on or modified part.

The California Air Resources Board’s Emission Warranty Parts List specifically defines

the emission-related warranted parts. (EPA’s regulations do not include a parts list,

but the EPA considers emission-related warranted parts to include all the parts listed

below.) Techtronic Industries North America, Inc., will provide any documents that

describe its warranty procedures or policies within five days upon request by the

California Air Resources Board.

EMISSIONS PARTS LIST

Emissions parts vary from product to product. Your emissions control system warranty

applies to any of the following components that may be included on your product:

(1) Fuel Metering System

(i) Carburetor and internal parts (and/or pressure regulator or fuel injection

system).

(ii) Air/fuel ratio feedback and control system.

(iii) Cold start enrichment system.

(iv) Fuel Tank.

(2) Air Induction System

(i) Controlled hot air intake system.

(ii) Intake manifold.

(iii) Air filter.

(3) Ignition System

(i) Spark Plugs.

(ii) Magneto or electronic ignition system.

(iii) Spark advance/retard system.

(4) Exhaust Gas Recirculation (EGR) System

(i) EGR valve body and carburetor spacer, if applicable.

(ii) EGR rate feedback and control system.

(5) Air Injection System

(i) Air pump or pulse valve.

(ii) Valves affecting distribution of flow.

(iii) Distribution manifold.

(6) Catalyst or Thermal Reactor System

(i) Catalytic converter.

(ii) Thermal reactor.

(iii) Exhaust manifold.

(7) Particulate Controls

(i) Traps, filters, precipitators, and any other device used to capture particulate

emissions.

(8) Miscellaneous Items Used in Above Systems

(i) Electronic controls.

(ii) Vacuum, temperature, and time sensitive valves and switches.

(iii) Hoses, belts, connectors, and assemblies.

Techtronic Industries North America, Inc., will furnish with each new engine written

instructions for its maintenance and use by the owner.

The Emissions Compliance Period referred to on the Emissions Compliance label

indicates the number of operating hours for which the engine has been shown to

meet Federal emission requirements. Category C=50 hours, B=125 hours, and

A=300 hours.

TECHTRONIC INDUSTRIES NORTH AMERICA, INC., LIMITED WARRANTY STATEMENT FOR FEDERAL

AND CALIFORNIA EMISSION CONTROL SYSTEMS NON-ROAD AND SMALL OFF-ROAD ENGINES

YOUR WARRANTY RIGHTS AND OBLIGATIONS

14 - English

EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS LIST

Emissions Parts Inspect Before Clean Every Replace Clean Every Replace Every

Each Use 5 Hours Every 25 Hours 25 Hours 50 Hours

or Yearly or Yearly

CATALYTIC MUFFLER ASSEMBLY ................................................................................................................... X

AIR FILTER ASSY

includes:

Filter Screen ..................................................... X

SPARK SCREEN ................................................................................................................................................X

CARBURETOR ASSY

includes:

Heat Dam ........................ X

Gaskets ........................... X

FUEL TANK ASSY

includes:

Fuel Lines ........................ X

Fuel Cap .......................... X

Fuel Filter

IGNITION ASSY

includes:

Spark Plug ........................................................................................ X

ALL EMISSIONS-RELATED PARTS ARE WARRANTED FOR THREE YEARS OR FOR THE PERIOD OF TIME PRIOR TO

THE PARTS FIRST SCHEDULED REPLACEMENT WHICHEVER COMES FIRST.

THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER

Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s

original emission level, please refer to the maintenance section below.

CALL US FIRST

For any questions about operating or maintaining your product,

call the Ryobi® Help Line!

Your product has been fully tested prior to shipment to ensure

your complete satisfaction.

WARRANTY

15 - English

NOTES

3 - Français

RÈGLES DE SÉCURITÉ GÉNÉRALES

AVERTISSEMENT :

LIRE ET VEILLER À BIEN COMPRENDRE TOUTES LES

INSTRUCTIONS. Le non respect de toutes les instruc-

tions ci-dessous peut entraîner un choc électrique, un

incendie et / ou des blessures graves.

CONSERVER CES INSTRUCTIONS

Ne pas laisser des enfants ou personnes n’ayant pas reçu

une formation adéquate utiliser cet outil.

Ne jamais lancer ou faire tourner le moteur dans un endroit

clos. Les gaz d’échappement peuvent être mortels.

Porter une protection oculaire avec écrans latéraux

certifiée conforme à la norme ANSI Z87.1, ainsi qu’une

protection auditive lors de l’utilisation de ce produit.

Garder tous les badauds, enfants et animaux domestiques

à une distance d’au moins 15 m (50 pi).

Porter des pantalons longs, manches longues, des

chaussures de travail et des gants épais. Ne pas porter

de vêtements amples, shorts, sandales, bijoux quels qu’ils

soient et ne pas travailler pieds nus.

Pour réduire les risques de happement par les pièces en

mouvement, ne pas porter de vêtements amples, foulards,

colliers, etc.

Attacher les cheveux longs pour les maintenir au-dessus

des épaules, afin qu’ils ne se prennent pas dans les pièces

en rotation.

Ne pas utiliser cet outil en état de fatigue, si l’on est

souffrant ou sous l’influence de l’alcool, de drogues ou

de médicaments.

Ne pas travailler sous un éclairage insuffisant.

Garder toutes les parties du corps à l’écart des pièces

en mouvement et des paries brûlantes de l’outil.

Porter un masque facial filtrant dans les milieux

poussiéreux afin de réduire le risque de lésions lié à

l’inhalation de poussière.

Examiner la zone de travail avant chaque utilisation. La

débarrasser de tous les objets tels que cailloux, verre

brisé, clous, fils métalliques, cordes, etc. risquant d’être

projetés ou de se prendre dans la machine.

Se tenir bien campé et en équilibre. Ne pas travailler

hors de portée. Le travail hors de portée risque de faire

perdre l’équilibre ou de causer un contact avec les

pièces brûlantes.

Ne jamais utiliser l’outil sans le pare-étincelles, qui se

trouve dans le silencieux.

Les produits utilisés sur les territoires des services

forestiers des États-Unis et de certains états doivent être

conformes aux réglementations de lutte contre l’incendie.

Cet outil est doté d’un pare-étincelles, toutefois, d’autres

dispositifs peuvent être requis. Consulter les autorités

locales et gouvernementales.

Laisser le moteur refroidir avant de remiser l’outil.

Vider le réservoir de carburant dans un contenant

approuvé pour l’essence et immobiliser l’unité avant de

la transporter dans un véhicule.

Manipuler le carburant avec précaution pour éviter les

risques d’incendies et de brûlures. Le carburant est

extrêmement inflammable.

Ne pas fumer pendant la manipulation du carburant.

Mélanger et conserver le carburant dans un bidon ou

jerrican approuvé pour l’essence.

Mélanger le carburant à l’extérieur, loin de toute flamme

ou source d’étincelles.

Poser la machine sur un sol nu, arrêter le moteur et le

laisser refroidir avant de faire le plein.

Desserrer le bouchon du réservoir lentement pour relâcher

la pression et éviter que le carburant s’échappe.

Une fois le réservoir plein, remettre le bouchon en place

et le serrer fermement.

Essuyer tout le carburant éventuellement répandu.

S’éloigner de 9 m (30 pi) du point d’approvisionnement

avant de lancer le moteur.

N’essayer en aucun cas de brûler le carburant répandu.

Utiliser exclusivement des pièces de rechange et

accessoire d’origine. L’usage de toute autre pièce

pourrait créer une situation dangereuse ou endommager

l’outil.

Entretenir l’outil conformément aux instructions de ce

manuel d’utilisation.

Inspecter l’outil avant chaque utilisation pour s’assurer

qu’il n’y a pas de pièces desserrées, de fuites ce

carburant, etc. Remplacer les pièces endommagées.

Ne pas utiliser l’unité sur une échelle, un toit, un arbre ou

un autre support instable. Le fait de se tenir bien campé

sur une surface solide permet de mieux contrôler la

soufflante dans des situations inattendues.

Avant de nettoyer, réparer ou inspecter, arrêter le mo-

teur et vérifier que toutes les pièces en mouvement sont

immobilisées. Déconnecter le fil de bougie et le garder

à l’écart de la bougie afin d’empêcher un démarrage ac-

cidentel.

Le dépannage de la soufflante / aspirateur doit exclusive-

ment être confié à un personnel qualifié. Les réparations

ou entretiens par des personnes non qualifiées peuvent

entraîner des blessures ou dommages à l’outil.

4 - Français

RÈGLES DE SÉCURITÉ PARTICULIÈRES

Toujours tenir la soufflante/aspirateur avec la main

droite pendant le soufflage. Consulter les instructions

d’UTILISATION présentées ultérieurement dans ce

manuel afin de connaître la position adéquate pour utiliser

l’aspirateur, et obtenir des renseignements supplémen-

taires.

Ne jamais rien insérer dans les tubes.

Utiliser exclusivement selon les instructions de ce man-

uel.

Ne pas utiliser l’aspirateur sans le sac, car des débris

pourraient être projetés et infliger des blessures graves.

Toujours fermer le sac complètement avant d’utiliser

l’aspirateur.

L’aubage de la roue en rotation peut entraîner des bles-

sures graves. Arrêter le moteur et s’assurer que l’aubage

de la roue a cessé de tourner avant d’ouvrir la porte de

l’aspirateur ou d’installer ou de changer les tuyaux. Ne

pas mettre les mains ou quelque objet que ce soit dans

les tubes installés sur la machine.

Ne jamais utiliser la soufflante sans les accessoires appro-

priés installés. Les tubes de soufflante doivent toujours

être installés lorsque la machine est utilisée en soufflante.

Lorsque la machine est utilisée pour aspirer, les tubes

d’aspiration et le sac doivent toujours être installés. Pour

éviter la projection de débris, s’assurer que la fermeture

à glissière de sac est complètement fermée lorsque le

moteur tourne.

Éviter les situations pouvant mettre le feu au sac. Ne pas

utiliser la machine à proximité de flammes vives. Ne pas

aspirer les cendres chaudes de cheminées, barbecues,

feux de bois, etc. Ne pas aspirer de mégots de cigares

ou cigarettes dont les cendres ne sont pas complètement

froides.

 Ne jamais placer la soufflante en marche sur une surface,

sauf si celle-ci est dure et propre. Le gravier, le sable et

les autres débris peuvent être aspirés dans l’entrée d’air

et projetés en direction de l’utilisateur ou des personnes

à proximité, ce qui peut entraîner des blessures graves.

 Pour réduire les risques de perte de l’ouïe causée par le

niveau sonore, porter une protection auditive.

 Pour réduire les risques de blessures infligées par des

pièces en rotation, arrêter le moteur avant d’installer ou

de retirer des accessoires. Toujours débrancher le fil de

bougie avant de procéder à un entretien ou d’accéder à

des pièces en mouvement.

 Ne jamais utiliser la soufflante à proximité d’un feu, d’un

poêle, de cendres chaudes, d’un barbecue, etc., sans

quoi le feu risque de se propager.

 Ne pas diriger la soufflante vers des personnes ou un

animaux.

 Ne jamais utiliser la soufflante sans les accessoires

appropriés installés. Les tubes doivent toujours être en

place.

APPROVISIONNEMENT EN CARBURANT

Le carburant est extrêmement inflammable. Lors de

l’utilisation, prendre les précautions nécessaires pour

réduire le risque de blessures graves.

Conserver le carburant dans une zone froide bien ventilée

à l’écart d’étincelles et / ou de matériels produisant des

flammes.

Conserver le carburant dans des jerrycans spécialement

conçus à cet effet.

Toujours faire le plein à l’extérieur et ne pas fumer pendant

cette opération.

Faire l’appoint de carburant avant de lancer le moteur. Ne

jamais retirer le bouchon du réservoir de carburant ni faire

l’appoint pendant que le moteur tourne ou est chaud.

Ne pas fumer pendant la manipulation du carburant.

Mélanger et conserver le carburant dans un bidon ou

jerrycan approuvé pour l’essence.

Mélanger le carburant à l’extérieur, loin de toute flamme

ou source d’étincelles.

Desserrer le bouchon du réservoir lentement pour relâcher

la pression et éviter que le carburant s’échappe.

Une fois le réservoir plein, remettre le bouchon en place

et le serrer fermement.

Essuyer tout le carburant éventuellement répandu.

S’éloigner de 9 m (30 pi) du point d’approvisionnement

avant de lancer le moteur.

N’essayer en aucun cas de brûler le carburant répandu.

Manipuler le carburant avec précaution pour éviter les

risques d’incendies et de brûlures. Le carburant est ex-

trêmement inflammable.

Si du carburant est répandu, ne pas essayer de lancer le

moteur, mais éloigner la machine et éviter de créer une

source d’inflammation jusqu’à ce que les vapeurs de

carburant se soient dissipées.

Remettre en place les bouchons de jerrycan et de réser-

voir de carburant et les serrer fermement.

Vider le réservoir de carburant dans un contenant ap-

prouvé pour l’essence et empêcher l’unité de bouger

avant de le transporter dans un véhicule.

Lors de la vidange du réservoir de carburant, utiliser

un bidon ou jerrycan approuvé pour la conservation de

carburant et procéder dans un endroit bien aéré.

Poser la machine sur un sol nu, arrêter le moteur et le

laisser refroidir avant de faire le plein.

Conserver ces instructions. Les consulter fréquemment

et les utiliser pour instruire les autres utilisateurs éven-

tuels. Si cet outil est prêté, il doit être accompagné de

ces instructions.

5 - Français

SYMBOLES

Certains des symboles ci-dessous peuvent être présents sur la produit. Veiller à les étudier et à apprendre leur

signification. Une interprétation correcte de ces symboles permettra d’utiliser la produit plus efficacement et de

réduire les risques.

SYMBOLE NOM EXPLICATION

Symbole d’alerte de sécurité Indique un risque de blessure potentiel.

Lire le manuel d’utilisation

Pour réduire les risques de blessures, l’utilisateur doit lire

et veiller à bien comprendre le manuel d’utilisation avant

d’utiliser ce produit.

Porter une protection oculaire et

auditive

Toujours porter une protection oculaire munie d’écrans

latéraux certifiée conforme à la norme ANSI Z87.1, ainsi

qu’une protection auditive et respiration lors de l’utilisation

de cet outil.

Volet d’aspiration

Ne pas actionner lorsque le volet d’aspiration n’est pas

verrouillé.

Cheveux longs Risque d’aspiration des cheveux longs dans l’entrée d’air.

Tubes de soufflante Ne pas utiliser sans les tubes en place.

Vêtements amples

Risque d’aspiration des vêtements amples dans l’entrée

d’air.

Essence et lubrifiant

Utiliser de l’essence sans plomb pour automobiles, avec un

indice d’octane de 87 [(R + M) / 2] ou plus. Cet outil utilise

un moteur deux temps qui nécessite le mélange d’essence

et d’lubrifiant 2 temps.

Les termes de mise en garde suivants et leur signification ont pour but d’expliquer le degré de risques associé à l’utilisation

de ce produit.

SYMBOLE SIGNAL SIGNIFICATION

DANGER :

Indique une situation extrêmement dangereuse qui, si elle n’est pas évitée,

aura pour conséquences des blessures graves ou mortelles.

AVERTISSEMENT :

Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée,

pourrait entraîner des blessures graves ou mortelles.

ATTENTION :

Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée,

pourraît entraîner des blessures légères ou de gravité modérée.

ATTENTION :

(Sans symbole d’alerte de sécurité) Indique une situation pouvant entraîner

des dommages matériels.

La page charge ...

Ryobi Blower RY09051 Manuel utilisateur

Marque: Ryobi

Modèle: Blower RY09051

Catégorie: Souffleurs / sécheurs d'air

Taper: Manuel utilisateur

Ce manuel convient également à

RY09051

Télécharger le PDF

rapport

dans d''autres langues

English: Ryobi Blower RY09051 User manual
español: Ryobi Blower RY09051 Manual de usuario

Ryobi Blower RY09051 Manuel utilisateur

Ce manuel convient également à

Ryobi Blower RY09051 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents