Ryobi RYAC130-S Manuel utilisateur

Marque: Ryobi

Modèle: RYAC130-S

Catégorie: Tondeuses à gazon

Taper: Manuel utilisateur

Ce manuel convient également à

Your lawn mower has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product.

Thank you for your purchase.

Ce tondeuse a été conçu et fabriqué conformément à nos

strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation. Correctement entretenu, cet outil vous donnera

des années de fonctionnement robuste et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre

le manuel d’utilisation avant d’employer ce produit.

Merci de votre achat.

Su podadora ha sido diseñado y fabricado de conformidad con

nuestras estrictas normas para brindar fiabilidad, facilidad de

uso y seguridad para el operador. Con el debido cuidado, le

brindará muchos años de sólido funcionamiento y sin problemas.

ADVERTENCIA: Para reducir el riesgo de

lesiones, el usuario debe leer y comprender el manual del

operador antes de usar este producto.

Le agradecemos su compra.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

SAVE THIS MANUAL FOR FUTURE REFERENCE

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

13 in. LAWN MOWER

TONDEUSE DE 330,2 mm (13 po)

PODADORA DE 330,2 mm (13 pulg.)

RYAC130

See this fold-out section for all of the figures

referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner toutes les

figures mentionnées dans le manuel d’utilisation.

Consulte esta sección desplegable para ver todas

las figuras a las que se hace referencia en el manual

del operador.

iii

Fig. 2

Fig. 4

Fig. 3

A - Lower handle (poignée inférieure, mango

inferior)

B - Upper handle assembly (ensemble de

poignée supérieure, conjunto del mango

superior)

C - Lock bolt (boulon de verrouillage, perno de

fijación)

D - Upper handle lock knob (bouton de verrou

de la poignée supérieure, perilla del seguro

del mango superior)

A - Rear discharge door (couvercle d’éjection

arrière, puerta de descarga posterior)

B - Rear discharge opening (ouverture d’éjection

arrière, abertura de descarga posterio)

C - Mulching plug (insert broyeur, tapón para

trituración)

A - Lower handle (poignée inférieure, mango

inferior)

B - Lower handle lock button (bouton de verrou

de la poignée inférieure, botón del seguro

del mango inferior)

A - Motor/blade control assembly (dispositif de

commande du moteur/de la lame, conjunto

de control del motor/hoja)

B - Start button (bouton « Start » [démarrer],

botón de arranque)

C - Upper handle (poignée supérieure, mango

superior)

D - Blade control lever (levier de commande de

la lame, palanca de control de la hoja)

E - Upper handle lock knob (bouton de verrou

de la poignée supérieure, perilla del seguro

del mango superior)

F - Lower handle (poignée inférieure, mango

inferior)

G - Height adjustment lever (levier de réglage de

la hauteur, palanca de ajuste de altura)

H - Mulching plug (insert broyeur, tapón para

trituración)

I - Grass catcher (collecteur d’herbe, receptor

de hierba)

J - Carrying handle (poignée de transport,

mango de acarreo)

K - Power cord (cordon d’alimentation, cable de

alimentación)

C - Power cord (cordon d’alimentation, cable de

alimentación)

D - Notches (encoches, muescas)

Fig. 1

15° MAXIMUM

15° MAXIMAL

15° MÁXIMA

Fig. 10

A - Extension cord (cordon prolongateurs,

cordón de extensión)

B - Cord retainer (retenue de cordon, retén

para el cable)

C - Extension cord receptacle (prise du cordon

prolongateurs, receptáculo del cordón de

extensión)

Fig. 7

A - Height adjustment lever (levier de réglage de

la hauteur, palanca de ajuste de altura)

B - Lowest blade setting (le plus bas réglage de

la lame, ajuste más bajo de la hoja)

C - Highest blade setting (le plus haut réglage de

la lame, ajustes de hoja más alto)

Fig. 6

Fig. 5

A - Grass catcher handle (poignée de collecteur

d’herbe, mango del receptor de hierba)

B - Slots (fentes, ranuras)

C - Rear discharge door (couvercle d’éjection

arrière, puerta de descarga posterior)

Fig. 8

D - Rear discharge opening (ouverture

d’éjection arrière, abertura de descarga

posterio)

E - Hooks (crochets, ganchos)

A - Slots (fentes, ranuras)

B - Hooks (crochets, ganchos)

Fig. 9

A - Start button (bouton démarrer, botón de

arranque)

B - Blade control lever (levier de commande de

la lame, palanca de control de la hoja)

Fig. 12

A - Blade (lame, hoja)

B - Wrench (clé, llave)

C - Block of wood (pièce de bois, bloque de

madera)

Fig. 13 Fig. 14

A - Shaft (arbre, eje)

B - Blade (lame, hoja)

C - Blade lock nut (écrou de blocage de lame,

tuerca de seguridad de la hoja)

D - Blade post (half circle) [tige pour

lame (demi-cercle), puerto de la hoja

(semicircular)]

E - Blade bolt hole (trou du boulon de lame,

orificio del perno de la hoja)

F - Blade hole (half circle) [trou pour

lame (demi-cercle), orificio de la hoja

(semicircular)]

TO STORE THE MACHINE

POUR REMISER L’ÉQUIPEMENT

PARA GUARDAR LA MÁQUINA

Fig. 11

2 — English

 Introduction ...................................................................................................................................................................... 2

Introduction / Introducción

 Important Safety Instructions ........................................................................................................................................3-5

Instructions importantes concernant la sécurité / Instrucciones de seguridad importantes

Symbols .........................................................................................................................................................................6-7

Symboles / Símbolos

Electrical ........................................................................................................................................................................... 8

Caractéristiques électriques / Aspectos eléctricos

 Features ............................................................................................................................................................................ 9

Caractéristiques / Características

 Assembly ...................................................................................................................................................................10-11

Assemblage / Armado

 Operation ...................................................................................................................................................................12-13

Utilisation / Funcionamiento

 Maintenance ..............................................................................................................................................................14-15

Entretien / Mantenimiento

 Troubleshooting .............................................................................................................................................................. 15

Dépannage / Solución de problemas

 Warranty ......................................................................................................................................................................... 16

Garantie / Garantía

 Parts Ordering and Service ...............................................................................................................................Back Page

Commande de pièces et réparation / Pedidos de piezas y servicio .......................................................... Page arrière / Pág. posterior

TABLE OF CONTENTS

TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO

INTRODUCTION

INTRODUCTION / INTRODUCCIÓN

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product making it easy to maintain and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la

conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à

utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto

se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.

3 — English

WARNING:

READ AND UNDERSTAND ALL INSTRUCTIONS.

Failure to follow all instructions listed below and on the

machine may result in electric shock, fire, and/or serious

personal injury.

READ ALL INSTRUCTIONS

This cutting machine is capable of amputating hands and

feet and throwing objects. Failure to observe all safety

instructions could result in serious injury or death.

Avoid dangerous environment — Do not use the lawn

mower in damp or wet conditions or operate in the rain.

Keep children away — Keep all bystanders, children, and

pets at least 100 ft. away. Stop machine if anyone enters

the area.

Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted to

the machine and the mowing activity. Never assume that

children will remain where you last saw them.

• Keep children out of the mowing area and under the

watchful care of a responsible adult other than the

operator.

• Be alert and turn mower off if a child enters the area.

• Never allow children to operate the machine.

• Use extra care when approaching blind corners, shrubs,

trees, or other objects that may block your view of a

child.

Dress properly — Wear heavy, long pants, long sleeves,

boots, and gloves. Do not wear loose fitting clothing,

short pants, sandals, or go barefoot. Do not wear jewelry

of any kind. They can be caught in moving parts.

Don’t overreach — Keep proper footing and balance at

all times. Overreaching can result in loss of balance.

Do not operate the equipment while barefoot or when

wearing sandals or similar lightweight footwear. Wear

protective footwear that will protect your feet and improve

your footing on slippery surfaces.

Do not leave the mower unattended while running.

Keep hands and feet away from cutting area. Keep clear

of the discharge opening at all times.

Operate the lawn mower only in daylight or good artificial

light.

Always wear safety glasses with side shields. Everyday

glasses have only impact resistant lenses. They are NOT

safety glasses. Following this rule will reduce the risk of

eye injury. Use face mask if operation is dusty.

Use safety glasses — Always wear eye protection with

side shields marked to comply with ANSI Z87.1. Use face

mask if operation is dusty.

Use the right appliance — Do not use the lawn mower

for any job except that for which it is intended.

Do not force the lawn mower — It will do the job better

and safer at the rate for which it was designed.

Stay alert — Watch what you are doing and use common

sense when operating the lawn mower. Do not operate

the mower while tired, upset or under the influence of

drugs, alcohol, or medication. A moment of inattention

while operating the lawn mower may result in serious

personal injury.

Maintain lawn mower with care — Keep machine in good

working condition. Keep blades sharp and guards in place

and in working order. Replace damaged or unevenly worn

blades before using mower for best performance.

Check all nuts, bolts, and screws at frequent intervals for

proper tightness to be sure the equipment is in safe work-

ing condition. Mower blades are sharp. Wrap the blade or

wear gloves, and use extra caution when servicing them.

Stop the motor, wait until the blade comes to a complete

stop, and disconnect from power supply before cleaning

the lawn mower, removing the grass catcher, or removing

the mulching plug.

 Replace blade if it is bent or cracked. An unbalanced

blade causes vibration that could damage the motor

drive unit or cause personal injury. Sharpen a dull blade

equally at each end to maintain the balance. Clean the

blade thoroughly and check its balance by supporting it

horizontally on a thin nail through its center hole. The nail

should be in a horizontal position. If either end of the blade

rotates downward, remove some metal from the heavy

of lower end until the blade is balanced. It is balanced

when neither end drops.

When not in use, mower should be stored indoors in a

dry, locked up place—out of the reach of children. The

extension cord should also be removed and stored in a

separate location out of the reach of children.

Always use safety protective devices. Do not operate the

mower without the entire grass catcher, mulching plug

and rear discharge door in place and working properly.

Follow manufacturer’s instructions for proper operation

and installation of accessories. Only use accessories

approved by the manufacturer.

 To reduce the risk of electric shock, this appliance has

a polarized plug (one blade is wider than the other) and

will require the use of a polarized extension cord. The

appliance plug will fit into a polarized extension cord only

one way. If the plug does not fit fully into the extension

cord, reverse the plug. If the plug still does not fit, obtain

a correct polarized extension cord. A polarized extension

cord will require the use of a polarized wall outlet. This

plug will fit into the polarized wall outlet only one way.

If the plug does not fit fully into the wall outlet, reverse

the plug. If the plug still does not fit, contact a qualified

IMPORTANT SAFETY INSTRUCTIONS

4 — English

IMPORTANT SAFETY INSTRUCTIONS

electrician to install the proper wall outlet. Do not change

the equipment plug, extension cord receptacle, or exten-

sion cord plug in any way.

 Ground Fault Circuit Interrupter (GFCI) protection should

be provided on the circuit(s) or outlet(s) to be used for

the lawn mower. Receptacles are available having built-

in GFCI protection and may be used for this measure of

safety.

 Inspect lawn mower cord periodically and if damaged,

have it repaired by an authorized service facility. Inspect

extension cords periodically and replace if damaged.

Keep handles dry, clean, and free from oil and grease.

 Warning — To prevent electric shock use only with an

extension cord suitable for outdoor use, such as SW,

SOW, STW, STOW, SJW, SJOW, SJTW, or SJTOW.

 Extension Cord - Make sure your extension cord set is in

good condition. When using an extension cord, be sure

to use one heavy enough to carry the current your prod-

uct will draw. For lengths less than 50 feet, No. 14 AWG

extension cord should be used. An undersized cord will

cause a drop in line voltage resulting in loss of power and

overheating. To reduce the likelihood of disconnection of

lawn mower cord from the cord set during operating use

the cord retainer described in this manual (Figure 8).

 Under normal usage the catcher assembly is subject

to deterioration and wear and should, therefore, be

frequently checked for replacement. Only use identical

replacement catcher assemblies.

 Don’t Abuse Cord — Never pull lawn mower by cord or

yank it to disconnect from receptacle. Keep cord from

heat, oil, and sharp edges.

 Risk of death or serious personal injury if power lines or

electric cords are contacted. Never operate mower over

electrical sources, cords, or wires.

Clear the work area before each use. Remove all objects

such as rocks, tree nuts, sticks, metal, wire, bones, toys,

or other objects which can be thrown by the blade. Stay

behind the handle when the motor is running.

Avoid holes, ruts, bumps, rocks, property stakes, or other

hidden objects. Uneven terrain could cause a slip and fall

accident.

Do not mow near drop-offs, ditches, or embankments.

Mow across the face of slopes, never up and down.

Exercise extreme caution when changing direction on

slopes.

Plan your mowing pattern to avoid discharge of material

toward roads, sidewalks, bystanders and the like. Also,

avoid discharging material against a wall or obstruction,

which may cause the material to ricochet back toward

the operator.

Do not mow on wet grass or excessively steep slopes.

Poor footing could cause a slip and fall accident. Walk,

never run.

Use extra care when approaching blind corners, shrubs,

trees, or other objects that may block your view.

Do not pull the mower backward unless absolutely nec-

essary. If you must back the mower away from a wall or

obstruction, first look down and behind to avoid tripping

or pulling the mower over your feet.

Never direct discharged material toward anyone. Avoid

discharging material against a wall or obstruction. Ma-

terial may ricochet back toward the operator. Stop the

blade when crossing gravel surfaces.

Objects struck by the lawn mower blade can cause severe

injuries to persons. The lawn should always be carefully

examined and cleared of all objects prior to each mowing.

If the lawn mower strikes a foreign object, follow these

steps:

• Stop the lawn mower by releasing the blade control

lever, wait until the blade comes to a complete stop,

and disconnect extension cord from power supply.

• Thoroughly inspect the mower for any damage.

• Replace the blade if it is damaged in any way. Repair

any damage before restarting and continuing to operate

the mower.

 Stop the motor, wait until the blade comes to a complete

stop and disconnect extension cord from power supply

before unclogging the chute. The cutting blade continues

to rotate for a few seconds after the motor is shut off.

Never place any part of the body in the blade area until

you are sure the blade has stopped rotating.

If the mower should start to vibrate abnormally, stop the

motor, disconnect the extension cord from the power

supply, and check immediately for the cause. Replace

the blade if it is unevenly worn or damaged in any way.

Vibration is generally a warning of trouble.

Service on the product must be performed by qualified

repair personnel only. Service or maintenance performed

by unqualified personnel could result in injury to the user

or damage to the product.

Use only authorized replacement parts when servicing

the product. Use identical replacement blades only. Use

of unauthorized parts may create a risk of serious injury

to the user, or damage to the product.

Maintain or replace safety instructions labels, as

necessary.

Disconnect from power supply — Disconnect extension

cord from power supply before storing, servicing, or

changing accessories such as blades. Such preventive

safety measures reduce the risk of starting the tool ac-

cidentally.

Stop the unit and disconnect the extension cord from

power supply when not in use. Carry or push the unit with

the motor stopped and the extension cord disconnected

from the power supply.

5 — English

IMPORTANT SAFETY INSTRUCTIONS

 Store idle lawn mower indoors — When not in use, mower

should be stored indoors in a dry, locked place out of

the reach of children. The extension cord should also

be removed and stored in a separate location out of the

reach of children.

Follow instructions for lubricating and changing acces-

sories.

Keep guards in place and in working order.

Keep blades sharp.

Keep hands and feet away from cutting area.

Only allow responsible adults, who are familiar with the

instructions, to operate this machine.

Never operate machine in a closed area.

Never tamper with safety devices. Check for proper op-

eration regularly.

Save these instructions. Refer to them frequently and use

them to instruct others who may use this product. If you

loan someone this tool, loan them these instructions also.

6 — English

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye Protection

Always wear eye protection with side shields marked to comply

with ANSI Z87.1.

Do Not Mow Over

Electric Cords

Risk of death or serious personal injury if power lines or electric

cords are contacted. Never operate mower over electrical

sources, cords, or wires.

Wet Conditions Alert Do not expose to rain or use in damp locations.

Electric Shock

Failure to use in dry conditions and to observe safe practices can

result in electric shock.

Keep Hands and Feet Away Keep hands and feet away from blade and cutting area.

No Reach Do not reach hands or feet under mower deck.

MAX 15˚

No Slope

Do not operate on inclines greater than 15º. Mow across the face

of slopes, never up and down.

Keep Children and

Bystanders Away

Keep all children and bystanders at least 100 ft. away.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or

serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

CAUTION:

Indicates a hazardous situation, that, if not avoided, may result in minor or

moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates information considered important, but

not related to a potential injury (e.g. messages relating to property damage).

SYMBOLS

7 — English

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Ricochet

Thrown objects can ricochet and result in personal injury or prop-

erty damage.

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Pow er

hrs Hours Time

Alternating Current Type of current

Class II Tool Double-insulated construction

SYMBOLS

8 — English

Make sure the extension cord is securely attached as shown

in Figure 8, then connect the plug end of the power cord

into the receptacle end of the extension cord. Check that

connection is secure.

**Ampere rating (on product data plate)

0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0

Cord Length Wire Size (A.W.G.)

25´ 16 16 16 16 14 14

50´ 16 16 16 14 14 12

100´ 16 16 14 12 10 —

**Used on 12 gauge - 20 amp circuit

NOTE: AWG = American Wire Gauge

WARNING:

Keep the extension cord clear of the working area.

Position the cord so that it will not get caught on lumber,

tools, or other obstructions while you are working with

a power tool. Failure to do so can result in serious per-

sonal injury.

WARNING:

Check extension cords before each use. If damaged

replace immediately. Never use product with a damaged

cord since touching the damaged area could cause elec-

trical shock resulting in serious injury.

To reduce the risk of electric shock, this appliance has a

polarized plug (one blade is wider than the other) and will

require the use of a polarized extension cord. The appliance

plug will fit into a polarized extension cord only one way. If

the plug does not fit fully into the extension cord, reverse

the plug. If the plug still does not fit, obtain a correct polar-

ized extension cord. A polarized extension cord will require

the use of a polarized wall outlet. This plug will fit into the

polarized wall outlet only one way. If the plug does not fit fully

into the wall outlet, reverse the plug. If the plug still does not

fit, contact a qualified electrician to install the proper wall

outlet. Do not change the equipment plug, extension cord

receptacle, or extension cord plug in any way.

WARNING:

To reduce the risk of electric shock, use only with an

extension cord intended for outdoor use, such as an

extension cord of cord type SW-A, SOW-A, STW-A,

STOW-A, SJW-A, SJOW-A, SJTW-A. or SJTOW-A.

ELECTRICAL

DOUBLE INSULATION

Double insulation is a concept in safety in electric power

tools, which eliminates the need for the usual three-wire

grounded power cord. All exposed metal parts are isolated

from the internal metal motor components with protecting in-

sulation. Double insulated tools do not need to be grounded.

WARNING:

The double insulated system is intended to protect

the user from shock resulting from a break in the tool’s

internal insulation. Observe all normal safety precautions

to avoid electrical shock.

NOTE: Servicing of a product with double insulation requires

extreme care and knowledge of the system and should be

performed only by a qualified service technician. For service,

we suggest you return the tool to your nearest authorized

service center for repair. Always use original factory replace-

ment parts when servicing.

ELECTRICAL CONNECTION

This product has a precision-built electric motor. It should

be connected to a power supply that is 120 volts, AC only

(normal household current), 60 Hz. A substantial voltage

drop will cause a loss of power and the motor will overheat. If

your product does not operate when plugged into an outlet,

double-check the power supply.

GFCI

Ground Fault Circuit Interrupter (GFCI) protection should be

provided on the circuit(s) or outlet(s) to be used for the prod-

uct. Receptacles are available having built-in GFCI protection

and may be used for this measure of safety.

EXTENSION CORDS

When using a power product at a considerable distance from

a power source, be sure to use an extension cord that has

the capacity to handle the current the product will draw. An

undersized cord will cause a drop in line voltage, resulting in

overheating and loss of power. Use the chart to determine

the minimum wire size required in an extension cord. Only

round jacketed cords listed by Underwriter’s Laboratories

(UL) should be used.

When working outdoors with a product, use an extension

cord that is designed for outside use. This type of cord is

designated with “W-A” or “W” on the cord’s jacket such

as an extension cord of cord type SW-A, SOW-A, STW-A,

STOW-A, SJW-A, SJOW-A, SJTW-A. or SJTOW-A..

Before using any extension cord, inspect it for loose or ex-

posed wires and cut or worn insulation.

9 — English

PRODUCT SPECIFICATIONS

Motor .................................120 V, AC only, 60 Hz, 11 Amps

Cutting Path ............................................................... 13 in.

Height Adjustments .................................. .75 in. to 2.25 in.

Wheel Size ............................................6 in. front, 8 in. rear

FEATURES

KNOW YOUR LAWN MOWER

See Figure 1.

The safe use of this product requires an understanding of

the information on the product and in this operator’s manual

as well as a knowledge of the project you are attempting.

Before use of this product, familiarize yourself with all op-

erating features and safety rules.

ADJUSTABLE HANDLE HEIGHT

The height of the handle is easily adjustable with the touch

of a button.

CARRYING HANDLE

The lawn mower has a carrying handle for easy transport.

CORD RETAINER

A convenient cord retainer helps keep the extension cord

connection secure during AC operation.

GRASS CATCHER

The grass catcher collects grass clippings and prevents

them from being discharged across your lawn as you mow.

HEIGHT ADJUSTMENT LEVER

The height adjustment lever provides cutting height

adjustments.

MOTOR/BLADE CONTROL ASSEMBLY

The motor/blade control assembly, located on the upper

handle of the mower, engages and disengages the motor

and blade.

MULCHING PLUG

Your mower is equipped with a mulching plug that covers

the rear discharge opening, which allows the mower blade

to cut and recut for finer clippings.

10 — English

WARNING:

Never operate the mower without the proper safety de-

vices in place and working. Never operate the mower with

damaged safety devices. Operating the mower with miss-

ing or damaged parts can result in serious personal injury.

PACKING LIST

Lawn Mower

Upper Handle Assembly

Lower Handle

Mulching Plug

Grass Catcher

Upper Handle Lock Knobs (2)

Upper Handle Lock Knob Bolts (2)

Operator’s Manual

INSTALLING AND ADJUSTING HANDLE

ASSEMBLY

See Figures 2 - 3.

To install lower handle:

 Insert the ends of the lower handle into the mounting

holes on the deck as shown.

NOTE: Make sure to keep the cord on the inside of the

handle when installing.

 Depress the lock button at the rear of the mounting hole

to allow the handle to slide into position.

NOTE: There are three height position notches that can

be adjusted by depressing the lock button and raising or

lowering the handle to the desired position.

To install upper handle assembly:

 Position the upper handle as shown and insert the lock

bolt through the matching holes at the bottom of the up-

per handle and the top of the lower handle.

NOTE: The lower handle has three hole settings for height

adjustment. Make sure you use the same height setting

for each side.

 Thread the upper handle lock knob onto the lock bolt.

 Repeat for other side.

 Pull up on the upper handle to raise it into operating po-

sition. Make sure that the upper handle is seated in the

grooves at the top of the lower handle.

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

WARNING:

Do not use this product if any parts on the Packing List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

WARNING:

If any parts are damaged or missing, do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

Do not connect to power supply until assembly is com-

plete and you are ready to mow. Failure to comply could

result in accidental starting and possible serious personal

injury.

WARNING:

To prevent accidental starting, do not make any adjust-

ments or installations with the power supply connected.

Accidental starting of the mower during assembly could

result in serious personal injury.

11 — English

DANGER:

Do not allow any part of the power cord on the mower

or extension cord to become pinched or trapped when

assembling or raising the handles. A pinched live power

cord can cause the handles to become electrically ener-

gized. Contact with electrically live conductive parts will

result in death by electrocution, electric shock, and/or

serious personal injury.

 To secure the upper handle in place, tighten the upper

handle knobs. Avoid pinching or trapping any power

cords.

NOTE: If the upper handle is loose or separated from

the lower handle, tighten the knobs on the upper handle

locks by turning them clockwise.

To lower the handle assembly:

 Loosen the upper handle lock knobs.

NOTE: Loosen the knobs on the upper handle by turning

them counterclockwise.

 Lower the upper handle. Avoid pinching or trapping any

power cords.

INSTALLING THE MULCHING PLUG

(FOR MULCHING OPERATION)

See Figure 4.

NOTE: When using the mulching plug, do not install the

grass catcher.

 Disconnect power supply.

 Lift and hold the rear discharge door.

 Grasp the mulching plug by its handle and insert it at a

slight angle, as shown.

 Push the mulching plug securely into place.

ASSEMBLY

 Lower the rear discharge door.

 Connect to power supply when you are ready to mow.

INSTALLING THE GRASS CATCHER

(FOR REAR BAGGING OPERATION)

See Figures 5 - 6.

NOTE: When using the grass catcher, do not install the

mulching plug.

 Disconnect power supply.

 Lift the rear discharge door.

 Lift the grass catcher by its handle and place under the

rear discharge door so that the hooks on the grass catcher

are seated onto the slots on the mower housing.

 Release the rear discharge door.

 Connect to power supply when you are ready to mow.

SETTING BLADE HEIGHT

See Figure 7.

When shipped, the wheels on the mower are set to a low-

cutting position. Before using the mower for the first time,

raise the cutting position to the height best suited for your

lawn. The average lawn should be between 1-1/2 in. to 2 in.

during cool months and between 2 in. and 3-1/4 in. during

hot months.

To adjust the blade height:

 Disconnect power supply.

 To raise the blade height, press inward on the height ad-

justment lever and move it toward the back of the mower.

 To lower the blade height, press inward on the height

adjustment lever and move it toward the front of the

mower.

 Connect to power supply when you are ready to mow.

12 — English

INSTALLING / REMOVING EXTENSION CORD

See Figure 8.

 Insert the female end of the extension cord into the

product as shown.

 Connect the male end of the extension cord to the power

source.

 Make sure the extension cord is secured before beginning

operation.

NOTICE:

Always use cord retainer to properly attach extension

cord to lawn mower. Failure to use cord retainer may

result in damage to lawn mower and/or extension cord.

STARTING / STOPPING THE MOWER

See Figures 8 - 9.

Connect to power supply.

Press and hold the start button. Pull the blade control

lever toward the handle and release the button to start

the mower.

To stop the mower, release the blade control lever.

MOWING TIPS

Make sure the lawn is clear of stones, tree nuts, sticks,

wires, and other objects that could damage the lawn

mower blades or motor. Do not mow over property stakes

or other metal posts. Such objects could damage the

blade or be accidentally thrown by the mower in any di-

rection and cause serious personal injury to the operator

and others.

For a healthy lawn, always cut off one-third or less of the

total length of the grass.

When cutting heavy grass, reduce walking speed to allow

for more effective cutting and a proper discharge of the

clippings.

Do not cut wet grass. It will stick to the underside of the

deck and prevent proper bagging or mulching of grass

clippings.

New or thick grass may require a narrower cut or a higher

cutting height.

Clean the underside of the mower deck after each use

to remove grass clippings, leaves, dirt, and any other

accumulated debris.

NOTE: Always stop mower, allow blades to completely

stop, and disconnect power supply before cleaning un-

derneath the mower.

DANGER:

Risk of death by electrocution or electric shock or seri-

ous personal injury if power lines or electric cords are

contacted. Never operate mower over electrical sources,

cords, or wires.

WARNING:

Do not allow familiarity with products to make you care-

less. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

Do not use any attachments or accessories not recom-

mended by the manufacturer of this product. The use of

attachments or accessories not recommended can result

in serious personal injury.

WARNING:

Always inspect mower for missing or damaged parts

and blade for damage, uneven, or excessive wear prior

to use. Use of the mower with damaged or missing parts

can result in serious personal injury.

WARNING:

Always disconnect from power supply when you are as-

sembling parts, making adjustments, cleaning, or when

not in use. Following these instructions will prevent ac-

cidental starting that could cause serious personal injury.

APPLICATIONS

You may use this product for the purpose listed below:

Mowing your lawn

WARNING:

To avoid accidental starting that could result in serious

personal injury, always disconnect from power supply

when moving or transporting the mower.

OPERATION

13 — English

SLOPE OPERATION

See Figure 10.

WARNING:

Slopes are a major factor related to slip and fall accidents

that can result in severe injury. Operation on slopes

requires extra caution. If you feel uneasy on a slope, do

not mow it. For your safety, do not attempt to mow slopes

greater than 15 degrees.

Mow across the face of slopes, not up and down. Exercise

extreme caution when changing direction on slopes.

Watch for holes, ruts, rocks, hidden objects, or bumps

which can cause you to slip or trip. Tall grass can hide

obstacles. Remove all objects such as rocks, tree limbs,

etc., which could be tripped over or thrown by the blade.

OPERATION

Always be sure of your footing. A slip and fall can cause

serious personal injury. If you feel you are losing your bal-

ance, release the upper blade control lever immediately.

Do not mow near drop-offs, ditches, or embankments;

you could lose your footing or balance.

EMPTYING THE GRASS CATCHER

See Figure 11.

 Stop the mower and allow blades to completely stop.

 Disconnect power supply.

 Lift the rear discharge door.

 Lift the grass catcher by its handle to remove from mower.

 Empty grass clippings.

 Lift the rear discharge door and reinstall the grass catcher

as described earlier in this manual.

 Connect to the power supply when you are ready to mow.

14 — English

WARNING:

Before performing any maintenance, make sure the

power supply is disconnected to avoid accidental starting

and possible serious personal injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

When servicing, use only authorized replacement parts.

Use of any other parts can create a hazard or cause

product damage.

NOTICE:

Periodically inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts

are replaced. Please contact customer service or an

authorized service center for assistance.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use

clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. Chemicals can damage, weaken, or

destroy plastic which can result in serious personal injury.

Remove any build-up of grass and leaves on or around

the motor cover. Wipe the mower clean with a dry cloth

occasionally. Do not use water.

LUBRICATION

All of the bearings in this product are lubricated with a

sufficient amount of high grade lubricant for the life of the

unit under normal operating conditions. Therefore, no further

bearing lubrication is required.

WARNING:

Always protect hands by wearing heavy gloves and/or

wrapping the cutting edges of the blade with rags and

other material when performing blade maintenance.

Contact with the blade could result in serious personal

injury.

REPLACING THE CUTTING BLADE

See Figures 12 - 13.

NOTE: Only use authorized replacement blades.

Stop the motor. Allow blade to come to a complete stop.

Disconnect the power supply.

Turn the mower on its side.

Wedge a block of wood between the blade and mower

deck to prevent the blade from turning.

Loosen the blade lock nut by turning it counterclockwise

(as viewed from bottom of mower) using a 15 mm wrench

or socket (not provided).

Remove the blade lock nut and blade.

Place the new blade onto the shaft. Ensure blade is

properly seated with the two blade posts inserted into

the holes on the blade. Make sure it is installed with the

curved ends pointing up toward the mower deck and

not down toward the ground. When seated properly, the

blade should be flat against the shaft.

Replace the blade, then thread the blade lock nut onto

the shaft bolt and finger tighten.

NOTE: Make certain all parts are replaced in the exact

order in which they were removed.

Torque the blade lock nut down clockwise using a torque

wrench (not provided) to ensure the bolt is properly

tightened. The recommended torque for the blade bolt

is 350 – 400 in. lbs.

WARNING:

Ensure blade is properly seated and the blade lock nut is

tightened to the torque specifications above. Failure to

properly attach the blade could cause it to come loose

or detach and result in possible serious personal injury.

STORING THE MOWER

See Figure 14.



Disconnect power supply

, and store in a secure location

out of the reach of children.

Before storage, wipe any dirt or debris.

Turn mower on its side and clean grass clippings that

have accumulated on the underside of the mower deck.

Wipe the mower clean with a dry cloth.

Check all nuts, bolts, knobs, screws, fasteners, etc., for

tightness.

MAINTENANCE

15 — English

TROUBLESHOOTING

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.

PROBLEM POSSIBLE CAUSE SOLUTION

Handle not in position. Handle locks not locked. Lock upper and lower handle locks.

Mower not starting. Power supply not connected. Connect to power supply.

Mower cutting grass unevenly. Lawn is rough or cutting height not set

properly.

Adjust the cutting height.

Mower not mulching properly. Wet grass clippings sticking to the

underside of the deck.

Wait until the grass dries before mowing.

Mower hard to push. High grass, rear of mower housing

and blade dragging in heavy grass, or

cutting height too low.

Raise cutting height.

Mower not bagging properly. Cutting height set too low. Raise cutting height.

Mower vibrating at higher speed. Blade is unbalanced, excessively or

unevenly worn.

Bent motor shaft.

Replace the blade.

Stop the motor and disconnect power

supply. Inspect for damage. Have

repaired by an authorized service

center before restarting.

Motor stops while cutting. Cutting height set too low. Raise the cutting height.

Inspect moving parts for damage, breakage, and wear.

Have repairs made on any damaged or missing parts.

Check blade for damage, uneven, or excessive wear and

replace blade if these conditions exist.

Lower the handle assembly as described earlier in this

manual.

Store mower indoors in a clean, dry place out of the reach

of children.

Do not store near corrosive materials such as fertilizer or

rock salt.

MAINTENANCE

16 — English

WARRANTY

LIMITED WARRANTY STATEMENT

Techtronic Industries North America, Inc., warrants to the

original retail purchaser that this RYOBI® brand outdoor

product is free from defect in material and workmanship

and agrees to repair or replace, at Techtronic Industries

North America, Inc.’s, discretion, any defective product

free of charge within these time periods from the date of

purchase.

 Three years if the product is used for personal, family

or household use;

 90 days, if used for any other purpose, such as

commercial or rental.

This warranty extends to the original retail purchaser only

and commences on the date of the original retail purchase.

Any part of this product found in the reasonable judgment

of Techtronic Industries North America, Inc. to be defective

in material or workmanship will be repaired or replaced

without charge for parts and labor by an authorized service

center for RYOBI® brand outdoor products (Authorized

Ryobi Service Center).

The product, including any defective part, must be returned

to an authorized Ryobi service center within the warranty

period. The expense of delivering the product to the service

center for warranty work and the expense of returning it

back to the owner after repair or replacement will be paid

by the owner. Techtronic Industries North America, Inc.’s,

responsibility in respect to claims is limited to making the

required repairs or replacements and no claim of breach of

warranty shall be cause for cancellation or rescission of the

contract of sale of any RYOBI® brand outdoor product. Proof

of purchase will be required by the dealer to substantiate

any warranty claim. All warranty work must be performed

by an authorized service dealer.

This warranty is limited to ninety (90) days from the date

of original retail purchase for any RYOBI® brand outdoor

product that is used for rental or commercial purposes, or

any other income-producing purpose.

This warranty does not cover any product that has been

subject to misuse, neglect, negligence, or accident, or that

has been operated in any way contrary to the operating

instructions as specified in this operator’s manual. This

warranty does not apply to any damage to the product that

is the result of improper maintenance or to any product

that has been altered or modified. The warranty does not

extend to repairs made necessary by normal wear or by the

use of parts or accessories which are either incompatible

with the RYOBI® brand outdoor product or adversely affect

its operation, performance, or durability. In addition, this

warranty does not cover:

A. Tune-ups – Spark Plugs, Carburetor, Carburetor

Adjustments, Ignition, Filters

B. Wear items – Bump Knobs, Outer Spools, Cutting

Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive

Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades,

Blower Fans, Blower and Vacuum Tubes, Vacuum Bag

and Straps, Guide Bars, Saw Chains

Techtronic Industries North America, Inc., reserves the

right to change or improve the design of any RYOBI® brand

outdoor product without assuming any obligation to modify

any product previously manufactured.

ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION

TO THE STATED WARRANTY PERIOD. ACCORDINGLY,

ANY SUCH IMPLIED WARRANTIES INCLUDING

MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR OTHERWISE, ARE DISCLAIMED

IN THEIR ENTIRETY AFTER THE EXPIRATION OF

THE APPROPRIATE THREE-YEAR OR NINETY-DAY

WARRANTY PERIOD. TECHTRONIC INDUSTRIES

NORTH AMERICA, INC.’S, OBLIGATION UNDER THIS

WARRANTY IS STRICTLY AND EXCLUSIVELY LIMITED TO

THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS

AND TECHTRONIC INDUSTRIES NORTH AMERICA,

INC., DOES NOT ASSUME OR AUTHORIZE ANYONE

TO ASSUME FOR THEM ANY OTHER OBLIGATION.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW

LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE

LIMITATION MAY NOT APPLY TO YOU. TECHTRONIC

INDUSTRIES NORTH AMERICA, INC., ASSUMES NO

RESPONSIBILITY FOR INCIDENTAL, CONSEQUENTIAL,

OR OTHER DAMAGES INCLUDING, BUT NOT LIMITED

TO, EXPENSE OF RETURNING THE PRODUCT TO AN

AUTHORIZED RYOBI SERVICE CENTER AND EXPENSE

OF DELIVERING IT BACK TO THE OWNER, MECHANIC’S

TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES,

RENTAL OF A LIKE PRODUCT DURING THE TIME

WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,

LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS

OF REVENUE, LOSS OF USE OF THE PRODUCT, LOSS

OF TIME, OR INCONVENIENCE. SOME STATES DO NOT

ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL

OR CONSEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

This warranty applies to all RYOBI® brand outdoor products

manufactured by or for Techtronic Industries North America,

Inc., and sold in the United States and Canada.

To locate your nearest Authorized Ryobi Service Center,

dial 1-800-860-4050.

La page charge ...

Ryobi RYAC130-S Manuel utilisateur

Marque: Ryobi

Modèle: RYAC130-S

Catégorie: Tondeuses à gazon

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Ryobi RYAC130-S User manual
español: Ryobi RYAC130-S Manual de usuario

Ryobi RYAC130-S Manuel utilisateur

Ce manuel convient également à

Ryobi RYAC130-S Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents