Ryobi ZRRYAC130 Manuel utilisateur

Ryobi
Marque
Ryobi
Modèle
ZRRYAC130
Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur

Ce manuel convient également à

Your lawn mower has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
Ce tondeuse a été conçu et fabriqué conformément à nos
strictes normes de fiabilité, simplicité d’emploi et sécurité
d’utilisation. Correctement entretenu, cet outil vous donnera
des années de fonctionnement robuste et sans problème.
AVERTISSEMENT : Pour réduire les risques de
blessures, l’utilisateur doit lire et veiller à bien comprendre
le manuel d’utilisation avant d’employer ce produit.
Merci de votre achat.
Su podadora ha sido diseñado y fabricado de conformidad con
nuestras estrictas normas para brindar fiabilidad, facilidad de
uso y seguridad para el operador. Con el debido cuidado, le
brindará muchos años de sólido funcionamiento y sin problemas.
ADVERTENCIA: Para reducir el riesgo de
lesiones, el usuario debe leer y comprender el manual del
operador antes de usar este producto.
Le agradecemos su compra.
CONSERVER CE MANUEL POUR
FUTURE RÉFÉRENCE
GUARDE ESTE MANUAL PARA
FUTURAS CONSULTAS
SAVE THIS MANUAL FOR FUTURE REFERENCE
OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
13 in. LAWN MOWER
TONDEUSE DE 330,2 mm (13 po)
PODADORA DE 330,2 mm (13 pulg.)
RYAC130
ii
See this fold-out section for all of the figures
referenced in the operator’s manual.
Consulter l’encart à volets afin d’examiner toutes les
figures mentionnées dans le manuel d’utilisation.
Consulte esta sección desplegable para ver todas
las figuras a las que se hace referencia en el manual
del operador.
iii
Fig. 2
Fig. 4
Fig. 3
A
A - Lower handle (poignée inférieure, mango
inferior)
B - Upper handle assembly (ensemble de
poignée supérieure, conjunto del mango
superior)
C - Lock bolt (boulon de verrouillage, perno de
fijación)
D - Upper handle lock knob (bouton de verrou
de la poignée supérieure, perilla del seguro
del mango superior)
A - Rear discharge door (couvercle d’éjection
arrière, puerta de descarga posterior)
B - Rear discharge opening (ouverture d’éjection
arrière, abertura de descarga posterio)
C - Mulching plug (insert broyeur, tapón para
trituración)
A - Lower handle (poignée inférieure, mango
inferior)
B - Lower handle lock button (bouton de verrou
de la poignée inférieure, botón del seguro
del mango inferior)
A - Motor/blade control assembly (dispositif de
commande du moteur/de la lame, conjunto
de control del motor/hoja)
B - Start button (bouton « Start » [démarrer],
botón de arranque)
C - Upper handle (poignée supérieure, mango
superior)
D - Blade control lever (levier de commande de
la lame, palanca de control de la hoja)
E - Upper handle lock knob (bouton de verrou
de la poignée supérieure, perilla del seguro
del mango superior)
C
B
B
F - Lower handle (poignée inférieure, mango
inferior)
G - Height adjustment lever (levier de réglage de
la hauteur, palanca de ajuste de altura)
H - Mulching plug (insert broyeur, tapón para
trituración)
I - Grass catcher (collecteur d’herbe, receptor
de hierba)
J - Carrying handle (poignée de transport,
mango de acarreo)
K - Power cord (cordon d’alimentation, cable de
alimentación)
C - Power cord (cordon d’alimentation, cable de
alimentación)
D - Notches (encoches, muescas)
Fig. 1
A
C
D
E
K
F
G
H
I
J
B
D
A
C
A
B
D
C
C
iv
15° MAXIMUM
15° MAXIMAL
15° MÁXIMA
Fig. 10
A - Extension cord (cordon prolongateurs,
cordón de extensión)
B - Cord retainer (retenue de cordon, retén
para el cable)
C - Extension cord receptacle (prise du cordon
prolongateurs, receptáculo del cordón de
extensión)
Fig. 7
A - Height adjustment lever (levier de réglage de
la hauteur, palanca de ajuste de altura)
B - Lowest blade setting (le plus bas réglage de
la lame, ajuste más bajo de la hoja)
C - Highest blade setting (le plus haut réglage de
la lame, ajustes de hoja más alto)
Fig. 6
Fig. 5
A - Grass catcher handle (poignée de collecteur
d’herbe, mango del receptor de hierba)
B - Slots (fentes, ranuras)
C - Rear discharge door (couvercle d’éjection
arrière, puerta de descarga posterior)
A
B
C
D
Fig. 8
A
A
B
C
A
B
D - Rear discharge opening (ouverture
d’éjection arrière, abertura de descarga
posterio)
E - Hooks (crochets, ganchos)
A - Slots (fentes, ranuras)
B - Hooks (crochets, ganchos)
E
B
Fig. 9
A - Start button (bouton démarrer, botón de
arranque)
B - Blade control lever (levier de commande de
la lame, palanca de control de la hoja)
C
A
B
B
v
Fig. 12
A - Blade (lame, hoja)
B - Wrench (clé, llave)
C - Block of wood (pièce de bois, bloque de
madera)
A
A
B
C
D
F
E
C
B
Fig. 13 Fig. 14
A - Shaft (arbre, eje)
B - Blade (lame, hoja)
C - Blade lock nut (écrou de blocage de lame,
tuerca de seguridad de la hoja)
D - Blade post (half circle) [tige pour
lame (demi-cercle), puerto de la hoja
(semicircular)]
E - Blade bolt hole (trou du boulon de lame,
orificio del perno de la hoja)
F - Blade hole (half circle) [trou pour
lame (demi-cercle), orificio de la hoja
(semicircular)]
TO STORE THE MACHINE
POUR REMISER L’ÉQUIPEMENT
PARA GUARDAR LA MÁQUINA
Fig. 11
F
2 — English
Introduction ...................................................................................................................................................................... 2
Introduction / Introducción
Important Safety Instructions ........................................................................................................................................3-5
Instructions importantes concernant la sécurité / Instrucciones de seguridad importantes
Symbols .........................................................................................................................................................................6-7
Symboles / Símbolos
Electrical ........................................................................................................................................................................... 8
Caractéristiques électriques / Aspectos eléctricos
Features ............................................................................................................................................................................ 9
Caractéristiques / Características
 Assembly ...................................................................................................................................................................10-11
Assemblage / Armado
Operation ...................................................................................................................................................................12-13
Utilisation / Funcionamiento
Maintenance ..............................................................................................................................................................14-15
Entretien / Mantenimiento
Troubleshooting .............................................................................................................................................................. 15
Dépannage / Solución de problemas
Warranty ......................................................................................................................................................................... 16
Garantie / Garantía
Parts Ordering and Service ...............................................................................................................................Back Page
Commande de pièces et réparation / Pedidos de piezas y servicio .......................................................... Page arrière / Pág. posterior
TABLE OF CONTENTS
TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO
INTRODUCTION
INTRODUCTION / INTRODUCCIÓN
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
* * *
Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la
conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à
utiliser et à entretenir.
* * *
Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto
se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.
3 — English
WARNING:
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below and on the
machine may result in electric shock, fire, and/or serious
personal injury.
READ ALL INSTRUCTIONS
This cutting machine is capable of amputating hands and
feet and throwing objects. Failure to observe all safety
instructions could result in serious injury or death.
Avoid dangerous environment — Do not use the lawn
mower in damp or wet conditions or operate in the rain.
Keep children away — Keep all bystanders, children, and
pets at least 100 ft. away. Stop machine if anyone enters
the area.
Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity. Never assume that
children will remain where you last saw them.
• Keep children out of the mowing area and under the
watchful care of a responsible adult other than the
operator.
• Be alert and turn mower off if a child enters the area.
• Never allow children to operate the machine.
• Use extra care when approaching blind corners, shrubs,
trees, or other objects that may block your view of a
child.
Dress properly — Wear heavy, long pants, long sleeves,
boots, and gloves. Do not wear loose fitting clothing,
short pants, sandals, or go barefoot. Do not wear jewelry
of any kind. They can be caught in moving parts.
Don’t overreach — Keep proper footing and balance at
all times. Overreaching can result in loss of balance.
Do not operate the equipment while barefoot or when
wearing sandals or similar lightweight footwear. Wear
protective footwear that will protect your feet and improve
your footing on slippery surfaces.
Do not leave the mower unattended while running.
Keep hands and feet away from cutting area. Keep clear
of the discharge opening at all times.
Operate the lawn mower only in daylight or good artificial
light.
Always wear safety glasses with side shields. Everyday
glasses have only impact resistant lenses. They are NOT
safety glasses. Following this rule will reduce the risk of
eye injury. Use face mask if operation is dusty.
Use safety glasses — Always wear eye protection with
side shields marked to comply with ANSI Z87.1. Use face
mask if operation is dusty.
Use the right appliance — Do not use the lawn mower
for any job except that for which it is intended.
Do not force the lawn mower — It will do the job better
and safer at the rate for which it was designed.
Stay alert — Watch what you are doing and use common
sense when operating the lawn mower. Do not operate
the mower while tired, upset or under the influence of
drugs, alcohol, or medication. A moment of inattention
while operating the lawn mower may result in serious
personal injury.
Maintain lawn mower with care — Keep machine in good
working condition. Keep blades sharp and guards in place
and in working order. Replace damaged or unevenly worn
blades before using mower for best performance.
Check all nuts, bolts, and screws at frequent intervals for
proper tightness to be sure the equipment is in safe work-
ing condition. Mower blades are sharp. Wrap the blade or
wear gloves, and use extra caution when servicing them.
Stop the motor, wait until the blade comes to a complete
stop, and disconnect from power supply before cleaning
the lawn mower, removing the grass catcher, or removing
the mulching plug.
Replace blade if it is bent or cracked. An unbalanced
blade causes vibration that could damage the motor
drive unit or cause personal injury. Sharpen a dull blade
equally at each end to maintain the balance. Clean the
blade thoroughly and check its balance by supporting it
horizontally on a thin nail through its center hole. The nail
should be in a horizontal position. If either end of the blade
rotates downward, remove some metal from the heavy
of lower end until the blade is balanced. It is balanced
when neither end drops.
When not in use, mower should be stored indoors in a
dry, locked up place—out of the reach of children. The
extension cord should also be removed and stored in a
separate location out of the reach of children.
Always use safety protective devices. Do not operate the
mower without the entire grass catcher, mulching plug
and rear discharge door in place and working properly.
Follow manufacturer’s instructions for proper operation
and installation of accessories. Only use accessories
approved by the manufacturer.
To reduce the risk of electric shock, this appliance has
a polarized plug (one blade is wider than the other) and
will require the use of a polarized extension cord. The
appliance plug will fit into a polarized extension cord only
one way. If the plug does not fit fully into the extension
cord, reverse the plug. If the plug still does not fit, obtain
a correct polarized extension cord. A polarized extension
cord will require the use of a polarized wall outlet. This
plug will fit into the polarized wall outlet only one way.
If the plug does not fit fully into the wall outlet, reverse
the plug. If the plug still does not fit, contact a qualified
IMPORTANT SAFETY INSTRUCTIONS
4 — English
IMPORTANT SAFETY INSTRUCTIONS
electrician to install the proper wall outlet. Do not change
the equipment plug, extension cord receptacle, or exten-
sion cord plug in any way.
Ground Fault Circuit Interrupter (GFCI) protection should
be provided on the circuit(s) or outlet(s) to be used for
the lawn mower. Receptacles are available having built-
in GFCI protection and may be used for this measure of
safety.
Inspect lawn mower cord periodically and if damaged,
have it repaired by an authorized service facility. Inspect
extension cords periodically and replace if damaged.
Keep handles dry, clean, and free from oil and grease.
Warning — To prevent electric shock use only with an
extension cord suitable for outdoor use, such as SW,
SOW, STW, STOW, SJW, SJOW, SJTW, or SJTOW.
Extension Cord - Make sure your extension cord set is in
good condition. When using an extension cord, be sure
to use one heavy enough to carry the current your prod-
uct will draw. For lengths less than 50 feet, No. 14 AWG
extension cord should be used. An undersized cord will
cause a drop in line voltage resulting in loss of power and
overheating. To reduce the likelihood of disconnection of
lawn mower cord from the cord set during operating use
the cord retainer described in this manual (Figure 8).
Under normal usage the catcher assembly is subject
to deterioration and wear and should, therefore, be
frequently checked for replacement. Only use identical
replacement catcher assemblies.
Don’t Abuse Cord — Never pull lawn mower by cord or
yank it to disconnect from receptacle. Keep cord from
heat, oil, and sharp edges.
Risk of death or serious personal injury if power lines or
electric cords are contacted. Never operate mower over
electrical sources, cords, or wires.
Clear the work area before each use. Remove all objects
such as rocks, tree nuts, sticks, metal, wire, bones, toys,
or other objects which can be thrown by the blade. Stay
behind the handle when the motor is running.
Avoid holes, ruts, bumps, rocks, property stakes, or other
hidden objects. Uneven terrain could cause a slip and fall
accident.
Do not mow near drop-offs, ditches, or embankments.
Mow across the face of slopes, never up and down.
Exercise extreme caution when changing direction on
slopes.
Plan your mowing pattern to avoid discharge of material
toward roads, sidewalks, bystanders and the like. Also,
avoid discharging material against a wall or obstruction,
which may cause the material to ricochet back toward
the operator.
Do not mow on wet grass or excessively steep slopes.
Poor footing could cause a slip and fall accident. Walk,
never run.
Use extra care when approaching blind corners, shrubs,
trees, or other objects that may block your view.
Do not pull the mower backward unless absolutely nec-
essary. If you must back the mower away from a wall or
obstruction, first look down and behind to avoid tripping
or pulling the mower over your feet.
Never direct discharged material toward anyone. Avoid
discharging material against a wall or obstruction. Ma-
terial may ricochet back toward the operator. Stop the
blade when crossing gravel surfaces.
Objects struck by the lawn mower blade can cause severe
injuries to persons. The lawn should always be carefully
examined and cleared of all objects prior to each mowing.
If the lawn mower strikes a foreign object, follow these
steps:
• Stop the lawn mower by releasing the blade control
lever, wait until the blade comes to a complete stop,
and disconnect extension cord from power supply.
• Thoroughly inspect the mower for any damage.
• Replace the blade if it is damaged in any way. Repair
any damage before restarting and continuing to operate
the mower.
Stop the motor, wait until the blade comes to a complete
stop and disconnect extension cord from power supply
before unclogging the chute. The cutting blade continues
to rotate for a few seconds after the motor is shut off.
Never place any part of the body in the blade area until
you are sure the blade has stopped rotating.
If the mower should start to vibrate abnormally, stop the
motor, disconnect the extension cord from the power
supply, and check immediately for the cause. Replace
the blade if it is unevenly worn or damaged in any way.
Vibration is generally a warning of trouble.
Service on the product must be performed by qualified
repair personnel only. Service or maintenance performed
by unqualified personnel could result in injury to the user
or damage to the product.
Use only authorized replacement parts when servicing
the product. Use identical replacement blades only. Use
of unauthorized parts may create a risk of serious injury
to the user, or damage to the product.
Maintain or replace safety instructions labels, as
necessary.
Disconnect from power supply — Disconnect extension
cord from power supply before storing, servicing, or
changing accessories such as blades. Such preventive
safety measures reduce the risk of starting the tool ac-
cidentally.
Stop the unit and disconnect the extension cord from
power supply when not in use. Carry or push the unit with
the motor stopped and the extension cord disconnected
from the power supply.
5 — English
IMPORTANT SAFETY INSTRUCTIONS
Store idle lawn mower indoors — When not in use, mower
should be stored indoors in a dry, locked place out of
the reach of children. The extension cord should also
be removed and stored in a separate location out of the
reach of children.
Follow instructions for lubricating and changing acces-
sories.
Keep guards in place and in working order.
Keep blades sharp.
Keep hands and feet away from cutting area.
Only allow responsible adults, who are familiar with the
instructions, to operate this machine.
Never operate machine in a closed area.
Never tamper with safety devices. Check for proper op-
eration regularly.
Save these instructions. Refer to them frequently and use
them to instruct others who may use this product. If you
loan someone this tool, loan them these instructions also.
6 — English
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye Protection
Always wear eye protection with side shields marked to comply
with ANSI Z87.1.
Do Not Mow Over
Electric Cords
Risk of death or serious personal injury if power lines or electric
cords are contacted. Never operate mower over electrical
sources, cords, or wires.
Wet Conditions Alert Do not expose to rain or use in damp locations.
Electric Shock
Failure to use in dry conditions and to observe safe practices can
result in electric shock.
Keep Hands and Feet Away Keep hands and feet away from blade and cutting area.
No Reach Do not reach hands or feet under mower deck.
MAX 15˚
No Slope
Do not operate on inclines greater than 15º. Mow across the face
of slopes, never up and down.
Keep Children and
Bystanders Away
Keep all children and bystanders at least 100 ft. away.
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
Indicates a hazardous situation, which, if not avoided, will result in death or
serious injury.
WARNING:
Indicates a hazardous situation, which, if not avoided, could result in death or
serious injury.
CAUTION:
Indicates a hazardous situation, that, if not avoided, may result in minor or
moderate injury.
NOTICE:
(Without Safety Alert Symbol) Indicates information considered important, but
not related to a potential injury (e.g. messages relating to property damage).
SYMBOLS
7 — English
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Ricochet
Thrown objects can ricochet and result in personal injury or prop-
erty damage.
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Pow er
hrs Hours Time
Alternating Current Type of current
Class II Tool Double-insulated construction
SYMBOLS
8 — English
Make sure the extension cord is securely attached as shown
in Figure 8, then connect the plug end of the power cord
into the receptacle end of the extension cord. Check that
connection is secure.
**Ampere rating (on product data plate)
0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length Wire Size (A.W.G.)
25´ 16 16 16 16 14 14
50´ 16 16 16 14 14 12
100´ 16 16 14 12 10 —
**Used on 12 gauge - 20 amp circuit
NOTE: AWG = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on lumber,
tools, or other obstructions while you are working with
a power tool. Failure to do so can result in serious per-
sonal injury.
WARNING:
Check extension cords before each use. If damaged
replace immediately. Never use product with a damaged
cord since touching the damaged area could cause elec-
trical shock resulting in serious injury.
To reduce the risk of electric shock, this appliance has a
polarized plug (one blade is wider than the other) and will
require the use of a polarized extension cord. The appliance
plug will fit into a polarized extension cord only one way. If
the plug does not fit fully into the extension cord, reverse
the plug. If the plug still does not fit, obtain a correct polar-
ized extension cord. A polarized extension cord will require
the use of a polarized wall outlet. This plug will fit into the
polarized wall outlet only one way. If the plug does not fit fully
into the wall outlet, reverse the plug. If the plug still does not
fit, contact a qualified electrician to install the proper wall
outlet. Do not change the equipment plug, extension cord
receptacle, or extension cord plug in any way.
WARNING:
To reduce the risk of electric shock, use only with an
extension cord intended for outdoor use, such as an
extension cord of cord type SW-A, SOW-A, STW-A,
STOW-A, SJW-A, SJOW-A, SJTW-A. or SJTOW-A.
ELECTRICAL
DOUBLE INSULATION
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-wire
grounded power cord. All exposed metal parts are isolated
from the internal metal motor components with protecting in-
sulation. Double insulated tools do not need to be grounded.
WARNING:
The double insulated system is intended to protect
the user from shock resulting from a break in the tool’s
internal insulation. Observe all normal safety precautions
to avoid electrical shock.
NOTE: Servicing of a product with double insulation requires
extreme care and knowledge of the system and should be
performed only by a qualified service technician. For service,
we suggest you return the tool to your nearest authorized
service center for repair. Always use original factory replace-
ment parts when servicing.
ELECTRICAL CONNECTION
This product has a precision-built electric motor. It should
be connected to a power supply that is 120 volts, AC only
(normal household current), 60 Hz. A substantial voltage
drop will cause a loss of power and the motor will overheat. If
your product does not operate when plugged into an outlet,
double-check the power supply.
GFCI
Ground Fault Circuit Interrupter (GFCI) protection should be
provided on the circuit(s) or outlet(s) to be used for the prod-
uct. Receptacles are available having built-in GFCI protection
and may be used for this measure of safety.
EXTENSION CORDS
When using a power product at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the product will draw. An
undersized cord will cause a drop in line voltage, resulting in
overheating and loss of power. Use the chart to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter’s Laboratories
(UL) should be used.
When working outdoors with a product, use an extension
cord that is designed for outside use. This type of cord is
designated with “W-A” or “W” on the cord’s jacket such
as an extension cord of cord type SW-A, SOW-A, STW-A,
STOW-A, SJW-A, SJOW-A, SJTW-A. or SJTOW-A..
Before using any extension cord, inspect it for loose or ex-
posed wires and cut or worn insulation.
9 — English
PRODUCT SPECIFICATIONS
Motor .................................120 V, AC only, 60 Hz, 11 Amps
Cutting Path ............................................................... 13 in.
Height Adjustments .................................. .75 in. to 2.25 in.
Wheel Size ............................................6 in. front, 8 in. rear
FEATURES
KNOW YOUR LAWN MOWER
See Figure 1.
The safe use of this product requires an understanding of
the information on the product and in this operator’s manual
as well as a knowledge of the project you are attempting.
Before use of this product, familiarize yourself with all op-
erating features and safety rules.
ADJUSTABLE HANDLE HEIGHT
The height of the handle is easily adjustable with the touch
of a button.
CARRYING HANDLE
The lawn mower has a carrying handle for easy transport.
CORD RETAINER
A convenient cord retainer helps keep the extension cord
connection secure during AC operation.
GRASS CATCHER
The grass catcher collects grass clippings and prevents
them from being discharged across your lawn as you mow.
HEIGHT ADJUSTMENT LEVER
The height adjustment lever provides cutting height
adjustments.
MOTOR/BLADE CONTROL ASSEMBLY
The motor/blade control assembly, located on the upper
handle of the mower, engages and disengages the motor
and blade.
MULCHING PLUG
Your mower is equipped with a mulching plug that covers
the rear discharge opening, which allows the mower blade
to cut and recut for finer clippings.
10 — English
WARNING:
Never operate the mower without the proper safety de-
vices in place and working. Never operate the mower with
damaged safety devices. Operating the mower with miss-
ing or damaged parts can result in serious personal injury.
PACKING LIST
Lawn Mower
Upper Handle Assembly
Lower Handle
Mulching Plug
Grass Catcher
Upper Handle Lock Knobs (2)
Upper Handle Lock Knob Bolts (2)
Operator’s Manual
INSTALLING AND ADJUSTING HANDLE
ASSEMBLY
See Figures 2 - 3.
To install lower handle:
Insert the ends of the lower handle into the mounting
holes on the deck as shown.
NOTE: Make sure to keep the cord on the inside of the
handle when installing.
Depress the lock button at the rear of the mounting hole
to allow the handle to slide into position.
NOTE: There are three height position notches that can
be adjusted by depressing the lock button and raising or
lowering the handle to the desired position.
To install upper handle assembly:
Position the upper handle as shown and insert the lock
bolt through the matching holes at the bottom of the up-
per handle and the top of the lower handle.
NOTE: The lower handle has three hole settings for height
adjustment. Make sure you use the same height setting
for each side.
Thread the upper handle lock knob onto the lock bolt.
Repeat for other side.
Pull up on the upper handle to raise it into operating po-
sition. Make sure that the upper handle is seated in the
grooves at the top of the lower handle.
ASSEMBLY
UNPACKING
This product requires assembly.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
WARNING:
Do not use this product if any parts on the Packing List
are already assembled to your product when you unpack
it. Parts on this list are not assembled to the product by
the manufacturer and require customer installation. Use
of a product that may have been improperly assembled
could result in serious personal injury.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the product.
If any parts are damaged or missing, please call
1-800-860-4050 for assistance.
WARNING:
If any parts are damaged or missing, do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this product or create acces-
sories not recommended for use with this product. Any
such alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
personal injury.
WARNING:
Do not connect to power supply until assembly is com-
plete and you are ready to mow. Failure to comply could
result in accidental starting and possible serious personal
injury.
WARNING:
To prevent accidental starting, do not make any adjust-
ments or installations with the power supply connected.
Accidental starting of the mower during assembly could
result in serious personal injury.
11 — English
DANGER:
Do not allow any part of the power cord on the mower
or extension cord to become pinched or trapped when
assembling or raising the handles. A pinched live power
cord can cause the handles to become electrically ener-
gized. Contact with electrically live conductive parts will
result in death by electrocution, electric shock, and/or
serious personal injury.
To secure the upper handle in place, tighten the upper
handle knobs. Avoid pinching or trapping any power
cords.
NOTE: If the upper handle is loose or separated from
the lower handle, tighten the knobs on the upper handle
locks by turning them clockwise.
To lower the handle assembly:
Loosen the upper handle lock knobs.
NOTE: Loosen the knobs on the upper handle by turning
them counterclockwise.
Lower the upper handle. Avoid pinching or trapping any
power cords.
INSTALLING THE MULCHING PLUG
(FOR MULCHING OPERATION)
See Figure 4.
NOTE: When using the mulching plug, do not install the
grass catcher.
Disconnect power supply.
Lift and hold the rear discharge door.
Grasp the mulching plug by its handle and insert it at a
slight angle, as shown.
Push the mulching plug securely into place.
ASSEMBLY
Lower the rear discharge door.
Connect to power supply when you are ready to mow.
INSTALLING THE GRASS CATCHER
(FOR REAR BAGGING OPERATION)
See Figures 5 - 6.
NOTE: When using the grass catcher, do not install the
mulching plug.
Disconnect power supply.
Lift the rear discharge door.
Lift the grass catcher by its handle and place under the
rear discharge door so that the hooks on the grass catcher
are seated onto the slots on the mower housing.
Release the rear discharge door.
Connect to power supply when you are ready to mow.
SETTING BLADE HEIGHT
See Figure 7.
When shipped, the wheels on the mower are set to a low-
cutting position. Before using the mower for the first time,
raise the cutting position to the height best suited for your
lawn. The average lawn should be between 1-1/2 in. to 2 in.
during cool months and between 2 in. and 3-1/4 in. during
hot months.
To adjust the blade height:
Disconnect power supply.
To raise the blade height, press inward on the height ad-
justment lever and move it toward the back of the mower.
To lower the blade height, press inward on the height
adjustment lever and move it toward the front of the
mower.
Connect to power supply when you are ready to mow.
12 — English
INSTALLING / REMOVING EXTENSION CORD
See Figure 8.
Insert the female end of the extension cord into the
product as shown.
Connect the male end of the extension cord to the power
source.
Make sure the extension cord is secured before beginning
operation.
NOTICE:
Always use cord retainer to properly attach extension
cord to lawn mower. Failure to use cord retainer may
result in damage to lawn mower and/or extension cord.
STARTING / STOPPING THE MOWER
See Figures 8 - 9.
Connect to power supply.
Press and hold the start button. Pull the blade control
lever toward the handle and release the button to start
the mower.
To stop the mower, release the blade control lever.
MOWING TIPS
Make sure the lawn is clear of stones, tree nuts, sticks,
wires, and other objects that could damage the lawn
mower blades or motor. Do not mow over property stakes
or other metal posts. Such objects could damage the
blade or be accidentally thrown by the mower in any di-
rection and cause serious personal injury to the operator
and others.
For a healthy lawn, always cut off one-third or less of the
total length of the grass.
When cutting heavy grass, reduce walking speed to allow
for more effective cutting and a proper discharge of the
clippings.
Do not cut wet grass. It will stick to the underside of the
deck and prevent proper bagging or mulching of grass
clippings.
New or thick grass may require a narrower cut or a higher
cutting height.
Clean the underside of the mower deck after each use
to remove grass clippings, leaves, dirt, and any other
accumulated debris.
NOTE: Always stop mower, allow blades to completely
stop, and disconnect power supply before cleaning un-
derneath the mower.
DANGER:
Risk of death by electrocution or electric shock or seri-
ous personal injury if power lines or electric cords are
contacted. Never operate mower over electrical sources,
cords, or wires.
WARNING:
Do not allow familiarity with products to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use of
attachments or accessories not recommended can result
in serious personal injury.
WARNING:
Always inspect mower for missing or damaged parts
and blade for damage, uneven, or excessive wear prior
to use. Use of the mower with damaged or missing parts
can result in serious personal injury.
WARNING:
Always disconnect from power supply when you are as-
sembling parts, making adjustments, cleaning, or when
not in use. Following these instructions will prevent ac-
cidental starting that could cause serious personal injury.
APPLICATIONS
You may use this product for the purpose listed below:
Mowing your lawn
WARNING:
To avoid accidental starting that could result in serious
personal injury, always disconnect from power supply
when moving or transporting the mower.
OPERATION
13 — English
SLOPE OPERATION
See Figure 10.
WARNING:
Slopes are a major factor related to slip and fall accidents
that can result in severe injury. Operation on slopes
requires extra caution. If you feel uneasy on a slope, do
not mow it. For your safety, do not attempt to mow slopes
greater than 15 degrees.
Mow across the face of slopes, not up and down. Exercise
extreme caution when changing direction on slopes.
Watch for holes, ruts, rocks, hidden objects, or bumps
which can cause you to slip or trip. Tall grass can hide
obstacles. Remove all objects such as rocks, tree limbs,
etc., which could be tripped over or thrown by the blade.
OPERATION
Always be sure of your footing. A slip and fall can cause
serious personal injury. If you feel you are losing your bal-
ance, release the upper blade control lever immediately.
Do not mow near drop-offs, ditches, or embankments;
you could lose your footing or balance.
EMPTYING THE GRASS CATCHER
See Figure 11.
Stop the mower and allow blades to completely stop.
Disconnect power supply.
Lift the rear discharge door.
Lift the grass catcher by its handle to remove from mower.
Empty grass clippings.
Lift the rear discharge door and reinstall the grass catcher
as described earlier in this manual.
Connect to the power supply when you are ready to mow.
14 — English
WARNING:
Before performing any maintenance, make sure the
power supply is disconnected to avoid accidental starting
and possible serious personal injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
When servicing, use only authorized replacement parts.
Use of any other parts can create a hazard or cause
product damage.
NOTICE:
Periodically inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please contact customer service or an
authorized service center for assistance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken, or
destroy plastic which can result in serious personal injury.
Remove any build-up of grass and leaves on or around
the motor cover. Wipe the mower clean with a dry cloth
occasionally. Do not use water.
LUBRICATION
All of the bearings in this product are lubricated with a
sufficient amount of high grade lubricant for the life of the
unit under normal operating conditions. Therefore, no further
bearing lubrication is required.
WARNING:
Always protect hands by wearing heavy gloves and/or
wrapping the cutting edges of the blade with rags and
other material when performing blade maintenance.
Contact with the blade could result in serious personal
injury.
REPLACING THE CUTTING BLADE
See Figures 12 - 13.
NOTE: Only use authorized replacement blades.
Stop the motor. Allow blade to come to a complete stop.
Disconnect the power supply.
Turn the mower on its side.
Wedge a block of wood between the blade and mower
deck to prevent the blade from turning.
Loosen the blade lock nut by turning it counterclockwise
(as viewed from bottom of mower) using a 15 mm wrench
or socket (not provided).
Remove the blade lock nut and blade.
Place the new blade onto the shaft. Ensure blade is
properly seated with the two blade posts inserted into
the holes on the blade. Make sure it is installed with the
curved ends pointing up toward the mower deck and
not down toward the ground. When seated properly, the
blade should be flat against the shaft.
Replace the blade, then thread the blade lock nut onto
the shaft bolt and finger tighten.
NOTE: Make certain all parts are replaced in the exact
order in which they were removed.
Torque the blade lock nut down clockwise using a torque
wrench (not provided) to ensure the bolt is properly
tightened. The recommended torque for the blade bolt
is 350 – 400 in. lbs.
WARNING:
Ensure blade is properly seated and the blade lock nut is
tightened to the torque specifications above. Failure to
properly attach the blade could cause it to come loose
or detach and result in possible serious personal injury.
STORING THE MOWER
See Figure 14.

Disconnect power supply
, and store in a secure location
out of the reach of children.
Before storage, wipe any dirt or debris.
Turn mower on its side and clean grass clippings that
have accumulated on the underside of the mower deck.
Wipe the mower clean with a dry cloth.
Check all nuts, bolts, knobs, screws, fasteners, etc., for
tightness.
MAINTENANCE
15 — English
TROUBLESHOOTING
IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.
PROBLEM POSSIBLE CAUSE SOLUTION
Handle not in position. Handle locks not locked. Lock upper and lower handle locks.
Mower not starting. Power supply not connected. Connect to power supply.
Mower cutting grass unevenly. Lawn is rough or cutting height not set
properly.
Adjust the cutting height.
Mower not mulching properly. Wet grass clippings sticking to the
underside of the deck.
Wait until the grass dries before mowing.
Mower hard to push. High grass, rear of mower housing
and blade dragging in heavy grass, or
cutting height too low.
Raise cutting height.
Mower not bagging properly. Cutting height set too low. Raise cutting height.
Mower vibrating at higher speed. Blade is unbalanced, excessively or
unevenly worn.
Bent motor shaft.
Replace the blade.
Stop the motor and disconnect power
supply. Inspect for damage. Have
repaired by an authorized service
center before restarting.
Motor stops while cutting. Cutting height set too low. Raise the cutting height.
Inspect moving parts for damage, breakage, and wear.
Have repairs made on any damaged or missing parts.
Check blade for damage, uneven, or excessive wear and
replace blade if these conditions exist.
Lower the handle assembly as described earlier in this
manual.
Store mower indoors in a clean, dry place out of the reach
of children.
Do not store near corrosive materials such as fertilizer or
rock salt.
MAINTENANCE
16 — English
WARRANTY
LIMITED WARRANTY STATEMENT
Techtronic Industries North America, Inc., warrants to the
original retail purchaser that this RYOBI® brand outdoor
product is free from defect in material and workmanship
and agrees to repair or replace, at Techtronic Industries
North America, Inc.’s, discretion, any defective product
free of charge within these time periods from the date of
purchase.
Three years if the product is used for personal, family
or household use;
90 days, if used for any other purpose, such as
commercial or rental.
This warranty extends to the original retail purchaser only
and commences on the date of the original retail purchase.
Any part of this product found in the reasonable judgment
of Techtronic Industries North America, Inc. to be defective
in material or workmanship will be repaired or replaced
without charge for parts and labor by an authorized service
center for RYOBI® brand outdoor products (Authorized
Ryobi Service Center).
The product, including any defective part, must be returned
to an authorized Ryobi service center within the warranty
period. The expense of delivering the product to the service
center for warranty work and the expense of returning it
back to the owner after repair or replacement will be paid
by the owner. Techtronic Industries North America, Inc.’s,
responsibility in respect to claims is limited to making the
required repairs or replacements and no claim of breach of
warranty shall be cause for cancellation or rescission of the
contract of sale of any RYOBI® brand outdoor product. Proof
of purchase will be required by the dealer to substantiate
any warranty claim. All warranty work must be performed
by an authorized service dealer.
This warranty is limited to ninety (90) days from the date
of original retail purchase for any RYOBI® brand outdoor
product that is used for rental or commercial purposes, or
any other income-producing purpose.
This warranty does not cover any product that has been
subject to misuse, neglect, negligence, or accident, or that
has been operated in any way contrary to the operating
instructions as specified in this operator’s manual. This
warranty does not apply to any damage to the product that
is the result of improper maintenance or to any product
that has been altered or modified. The warranty does not
extend to repairs made necessary by normal wear or by the
use of parts or accessories which are either incompatible
with the RYOBI® brand outdoor product or adversely affect
its operation, performance, or durability. In addition, this
warranty does not cover:
A. Tune-ups – Spark Plugs, Carburetor, Carburetor
Adjustments, Ignition, Filters
B. Wear items – Bump Knobs, Outer Spools, Cutting
Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive
Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades,
Blower Fans, Blower and Vacuum Tubes, Vacuum Bag
and Straps, Guide Bars, Saw Chains
Techtronic Industries North America, Inc., reserves the
right to change or improve the design of any RYOBI® brand
outdoor product without assuming any obligation to modify
any product previously manufactured.
ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION
TO THE STATED WARRANTY PERIOD. ACCORDINGLY,
ANY SUCH IMPLIED WARRANTIES INCLUDING
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR OTHERWISE, ARE DISCLAIMED
IN THEIR ENTIRETY AFTER THE EXPIRATION OF
THE APPROPRIATE THREE-YEAR OR NINETY-DAY
WARRANTY PERIOD. TECHTRONIC INDUSTRIES
NORTH AMERICA, INC.’S, OBLIGATION UNDER THIS
WARRANTY IS STRICTLY AND EXCLUSIVELY LIMITED TO
THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS
AND TECHTRONIC INDUSTRIES NORTH AMERICA,
INC., DOES NOT ASSUME OR AUTHORIZE ANYONE
TO ASSUME FOR THEM ANY OTHER OBLIGATION.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU. TECHTRONIC
INDUSTRIES NORTH AMERICA, INC., ASSUMES NO
RESPONSIBILITY FOR INCIDENTAL, CONSEQUENTIAL,
OR OTHER DAMAGES INCLUDING, BUT NOT LIMITED
TO, EXPENSE OF RETURNING THE PRODUCT TO AN
AUTHORIZED RYOBI SERVICE CENTER AND EXPENSE
OF DELIVERING IT BACK TO THE OWNER, MECHANIC’S
TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES,
RENTAL OF A LIKE PRODUCT DURING THE TIME
WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,
LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS
OF REVENUE, LOSS OF USE OF THE PRODUCT, LOSS
OF TIME, OR INCONVENIENCE. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
This warranty applies to all RYOBI® brand outdoor products
manufactured by or for Techtronic Industries North America,
Inc., and sold in the United States and Canada.
To locate your nearest Authorized Ryobi Service Center,
dial 1-800-860-4050.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Ryobi ZRRYAC130 Manuel utilisateur

Ryobi
Marque
Ryobi
Modèle
ZRRYAC130
Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents