DCS BGB30-BQRN-70004A Le manuel du propriétaire

A MESSAGE TO OUR CUSTOMERS

Thank you for selecting this DCS Professional "BGB" Series Grill. Because of this appliance's unique features we

have developed this Use & Care Guide. It contains valuable information on how to properly install, operate and

maintain your new appliance for years of safe and enjoyable cooking.

To help serve you better, please fill out and submit your Product Registration by visiting our website at

www.dcsappliances.com and selecting "Customer Care" on the home page and then select "Product

Registration". In addition, keep this guide handy, as it will help answer questions that may arise as you use your

new appliance.

For your convenience, product questions can be answered by a DCS Customer Care Representative at

1-888-936-7872, or emaih [email protected].

NOTE: Please write the Model, Code, and Serial Numbers on this page for reference (can be found on the inside,

right side panel behind the drip pan handle. See page 21.)

MODEL NUMBER CODE SERIAL NUMBER

NOTE: Inspect the product to verify that there is no shipping damage. If any damage is detected, call the shipper

and initiate a damage claim. DCS by Fisher & Paykel is not responsible for shipping damage.

DO NOT discard any packing material (box, pallet, straps) until the unit has been inspected.

WARNING!

Do not try lighting this appliance without reading the "Lighting Instructions" section of this manual.

Improper installation, adjustment, alteration, service or maintenance can cause property damage,

injury or death. Read the installation, operating and maintenance instructions thoroughly before use,

installing or servicing this equipment.This outdoor cooking gas appliance is not intended to be

installed in or on recreational vehicles, boats or in a non-ventilated room. For outdoor use only.

WARNING

1. Do Not store or use gasoline or any other flammable vapors and liquids in the vicinity of

this or any other appliance.

2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other

appliance.

DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flames.

3. Open lid.

4. If odor continues, keep away from the appliance and immediately call your gas supplier or

your fire department.

PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.

CONTENTS

SAFETY PRACTICES & PRECAUTIONS

GRILL MODELS

INSTALLATION

Locating Grill/Built-in Clearances

Built-in Construction Details

Cart Assembly Instructions

Gas Hook-up

Leak Testing

Burner Adjustment

Radiant Assembly

Installer Checklist

USING THE GRILL

Lighting Instructions

Grilling

USING THE ROTISSERIE

CARE & MAINTENANCE

TROUBLESHOOTING

SERVICE

WARRANTY

3-5

6

7-9

10-11

12-15

16-19

20

21

22

23

24

25-26

27-30

31-32

33

34

35-36

SAFETY PRACTICES & PRECAUTIONS

1.

2.

IMPORTANT SAFETY NOTICE!

Certain Liquid Propane dealers may fill liquid propane cylinders for usein the grill beyond cylinder filling capacity.

This"Overfilling" may create adangerous condition.

"Overfilled"tanks can build up excess pressure. As a safety device, the tank pressure relief valve will vent

propane gas vapor to relieve this excess pressure. This vapor is combustible and therefore can be ignited. To

reduce this danger, you should take the following safety precautions:

When you have your tank filled, be sure you tell the supplier to fill it to no more than 3/4 (75%) of its total

capacity.

If you own or use a spare tank, or have a disconnected tank, you should NEVER

store it near or under the grill/cart unit or heat box, or near any other ignition or

heat source. A metallic sticker with this warning is provided with the grill to

remind you, your family and all others who may use your grill of these safety

precautions. Install this sticker close to your barbeque grill.

3. Do not store a full tank in direct sunlight.

WARNING!

Do not try lighting this appliance without reading the "LIGHTING INSTRUCTIONS"

section of this manual. This grill isfor outdoor use only.

WARNING!

Push and hold the igniter button, turn the selected burner knob to "HI". If burner does

not light in 4 to S seconds turn knob"OFF"and wait S minutes before trying again for

any accumulated gas to dissipate.

STICKER

Begin by insuring proper installation and

servicing. Follow the installation instructions

within this manual. Have your grill installed

by a qualified installer. Have the installer

show you where the gas supply shut-off valve

is located so that you know where and how to

shut off the gas to the grill. If you smell gas,

your installer has not done a proper job of

checking for leaks. If the connections are not

perfectly sealed, you can have a small leak

and therefore a faint gas smell. Finding a leak

is not a "do-it-yourself" procedure. Some

leaks can only be found with the burner

control in the "ON" position and this must be

done by a qualified technician.

Children should not be left alone or unattended in an area where the grill is being used. Never allow them to sit,

stand or play on or around the grill at any time. When in use, portions of the grill get hot enough to cause

severe burns.

Do not store items of interest to children around or below the grill, in the cart or masonry enclosure. Never

allow children to crawl inside a cart or enclosure.

Never attach or disconnect an LP cylinder, or move or alter gas fittings when the grill is in operation or is hot.

Clean and perform general maintenance on the grill twice a year. Watch for corrosion, cracks, or insect activity.

Check the regulator, hoses, burner ports, air shutter, and venturi/valve section carefully. Always turn off gas at

the source (tank or supply line) prior to inspecting parts.

SAFETY PRACTICES & PRECAUTIONS

• After a period of storage or non-use (such as over the winter), the gas grill should be checked for gas leaks,

deterioration, proper assembly, and burner obstructions before using.

• Never let clothing, pot holders or other flammable materials come in contact with or get too close to any grate,

burner or hot surface until it has cooled. Fabric may ignite and result in personal injury.

• Do not heat unopened food containers as a build-up of pressure may cause the container to burst.

• Always use a covered hand when opening the grill lid and only do so slowly to allow heat and steam to escape.

• Never lean over an open grill. When lighting a burner, always pay close attention to what you are doing. Be

certain you are pushing the ignition button when you attempt to light the grill.

• After lighting burners, make sure burners are operating normally (see page 19).

• When using the grill, do not touch the grill burner, grate or immediate surrounding area as these areas become

extremely hot and could cause burns.

• Grease is flammable. Let hot grease cool before attempting to handle it. Avoid letting grease deposits collect in

the drip pan. Clean often.

• Do not use aluminum foil to line drip pans, grill grates or radiants. This can severely upset combustion air flow or

trap excessive heat in the control area. The result of this can be melted knobs or damaged ignition components.

• Do not operate with a damaged cord or plug.

For personal safety, wear proper apparel. Loose fitting garments or sleeves should never be worn while using

this appliance. Some synthetic fabrics are highly flammable and should not be worn while cooking. Only certain

types of glass, heat-proof glass ceramic, earthenware, or other glazed utensils are suitable for grill use. Use of

these types of materials may break with sudden temperature changes. Use only on low or medium heat settings

according to the manufacturer's directions.

WARNING!

Spiders and insects can nest in the grill burners, causing the gas not to flow through the burner. The gas will flow

from the front of the burner into the control panel. This is a very dangerous condition which can cause a fire to occur

behind the valve panel, thereby damaging the grill components and making it unsafe to operate.

WARNING!

Keep the area surrounding the grill free from combustible materials, trash, or combustible fluids and vapors such as

gasoline or charcoal lighter fluid. Do not obstruct the flow of combustion and ventilation air.

WARNING!

Never use the grill in windy conditions. If located in a consistently windy area (oceanfront, mountaintop, etc.) a wind

break will be required. Always adhere to the specified clearances listed.

GRILL PLACEMENT

PREFERRED

AIR FLOW

--9

GRILL EXHAUST EXHAUSTVENT FLOW

Wind hitting the grill A

WIND while in use, eL w\_D

especially winds :, i --A

blowing into or across T

this hood gap, can _/j

causepoor ._-___r *_?

performance and in

somecasescancaose _--

FLAME the control panelanddangerouslyknObsto get hot. _-- _ 3n_j_'in

4

If wind is an

issue, a wind

screen should

be added. The

wind screen

should be

higher than

the top of the

opening in the

back of the

grill and

minimum of 3"

clearance from

the back of the

grill for the lid.

SAFETY PRACTICES & PRECAUTIONS

When using the side burners always use flat bottomed pans which are large enough to cover the side burner.

Adjust the flame so that it heats only the bottom of the pan to avoid ignition of clothing. Position handles inward

away from open edges of the unit to avoid burns associated with unintentionalspillovers. Hold the handle of the

pan to prevent movement of it when turning or stirring food. For proper lighting and performance of the burners

keep the ports clean. It is necessary to clean periodically for optimum performance.

Clean the grill with caution. Avoid steam burns; do not use a wet sponge or cloth to clean the grill while it is hot.

Some cleaners produce noxious fumes or can ignite if applied to a hot surface.

Be sure all grill controls are turned off and the grill is cool before using any type of aerosol cleaner on or around

the grill. The chemical that produces the spraying action could, in the presence of heat, ignite or cause metal

parts to corrode.

Do not use the grill for cooking excessively fatty meats or products which promote flare-ups.

Never grill without the drip pan and grease tray in place and pushed all the way to the back of the grill. Without it

hot grease could leak downward and produce a fire or explosion hazard.

Do not operate the grill under unprotected combustible construction. Use only in well ventilated areas. Do not

use in buildings, garages, sheds, breezeway, covered structure or other such enclosed areas. This unit is for

outdoor use only.

If a cart unit is stored indoors, ensure that it is cool, fold the side shelf down, then push, never pull, the grill and

never push or pull on the side shelves. IfLP, the cylinder must be unhooked and the LP cylinder stored outside in

a well ventilated area, out of reach of children.

• Never use the grill in a windy area.

• Do not use charcoal or lighter fluid in the grill.

• Keep any electrical supply cord, or the rotisserie motor cord away from the heated areas of the grill and water

(pools, fountains, puddles).

• Never use a dented or rusty LP tank. Keep the ventilation openings of the cylinder enclosure free and clear from

debris.

• Use only dry potholders; moist or damp potholders on hot surfaces may cause burns from steam. Do not usea

towel or bulky cloth in place ofpotholders. Do not let potholders touch hot portions of the grill or burner grate.

• Have an ABC rated Fire Extinguisher accessible - never attempt to extinguish a grease fire with water or other

liquids.

• To avoid burns when cooking, use long handled BBQ tools.

• Do not move the appliance during its use.

• This unit is for outdoor use only! Do not operate in enclosed areas. This could result in carbon monoxide build-up

which would result in injury or death.

• When using the grill, be sure that all parts of the unit are firmly in place and that the grill is stable (can't be tipped

over).

To put out flare-ups, adjust the controls to lower the temperature

CALIFORNIA PROPOSITION 6S-WARNING: The Burning of gas cooking fuel generates some by-products which are

on the list of substances which are known by the State of California to cause cancer or reproductive harm.

California law requires businesses to warn customers of potential exposure to such substances. To minimize

exposure to these substances, always operate this unit according to the Use and Care Guide, ensuring you

provide good ventilation when cooking with gas.

This outdoor cooking gas appliance is not intended to be installed in or on recreational vehicles, trailers and/or

boats.

Note:

This product must be installed by a licensed plumber or gas fitter when installed within the Commonwealth of

Massachusetts.

5

GRILL MODELS

BGB30-BQR

6

INSTALLATION

LOCATING GRILL/BUILT-IN CLEARANCES

LOCATION:

When determining a suitable location take into account concerns such as exposure to wind, proximity to traffic

paths and keeping any gas or electrical supply lines as short as possible and away from heat sources. Locate the

grill only in a well ventilated area. Do not build the grill under overhead unprotected combustible construction.

Never locate the grill ina building, garage, breezeway, shed or other such enclosed areas. During heavy use, the

grill will produce a lot of heat and smoke. Ensure there is adequate area for it to dissipate.

If locating the grill in a windy area, try to locate the grill so the prevailing wind will blow air at the front of the

grill as shown in Fig. 01.This will assist the grill in venting hot air thru the back of the grill. In addition, this will

help keep any smoke from blowing at someone who is cooking on the grill. If you have to locate the grill in a

windy area where the prevailing wind is at the rear of the grill, a windbreak must be installed. The windbreak

should be made such that it will block wind from entering the exhaust vent in the rear of the unit as shown in

Fig. 01.

As high-performance gas appliance, your grill requires significant amounts of air to support the combustion

process. Your grill is designed to take air in through the valve panel area, and send the exhaust products out

through the exhaust gap at the rear of the hood. Using your grill in windy conditions can disrupt the proper flow

of air though your grill, leading to reduced performance, or in certain severe cases, causing heat buildup in the

valve panel area. This can lead to problems such as having the knobs melt, or burn hazards when the valve

panel surfaces become too hot to touch.

During high wind conditions, it is best if you don't use your grill. If you live in an area that is subject to frequent

high winds, or a steady directional wind, then the installation of a suitable windbreak may be advised. If you

have a grilling cart, it is best to position the unit so the prevailing wind blows into the valve panel, thus

supporting the proper airflow. Winds hitting the back of the grill directly are the most likely to cause problems,

although wind blowing along the exhaust gap in the rear can also be problematic.

Please note that damage to your grill resulting from use in windy conditions, such as melted knobs or igniter

wires, or valve panel discoloration from heat build-up, are excluded from warranty coverage.

GRILL PLACEMENT

PREFERRED

AIR FLOW

0000000

GRILL EXHAUST

WIND

EXHAUSTVENT FLOW

Wind hitting the grill

while in use, W\ND

especially winds

T

blowing into or across /

this hood gap, can 15"min.

cause poor |

performance and in £

some cases can cause

the control panel and _ I_/"

knobs to get _'in.

dangerously hot.

C_

z

FIG. 01

Important!

Gas fittings, regulator, and installer supplied shut-off valves must be easily accessible.

If wind is an

issue, a wind

screen should

be added. The

wind screen

should be

higher than

the top of the

opening in the

back of the

grill and

minimum of 3"

clearance from

the backof the

grill for the lid.

INSTALLATION

LOCATING GRILL/BUILT-IN CLEARANCES

Clearances to Non-Combustible Construction*:

A minimum of 3" clearance from the back of the grill to non-combustible construction is required for the purpose

of allowing the lid to open fully. It is desirable to allow at least 6" rear and side clearance to non-combustible

construction above the cooking surface for counter space. If you'll be using the rotisserie option, the space is

essential for motor and skewer clearance. The grill can be placed directly adjacent to non-combustible

construction below the cooking surface. (Fig. 02).

Clearances to Non-Combustible Construction*

......... [ 30" MOdels =39"(withrotisserie motor mounted) ] .........................................

26-1/2"

9rill

exnau

- 25-1/2

non-combustible

construction /

minimum

lid clearance)

10-1/16"

FIG. 02

WARNING!

Failure to maintain required clearances creates a fire hazard that may result in property damage or serious personal

injury.

WARNING!

The BGB Grill is designed to function in an open area. Recommended minimum clearances should be maintained to

all surfaces (combustible and noncombustible) for optimum performance. Noncombustible material within the mini-

mum clearance area could result in discoloration or deterioration.

WARNING!

If a noncombustible material such as stucco is covering a combustible material such as wood, the minimum clear-

ance distance needs to be held to the wood. The presence of a noncombustible material inside the clearance zone

does not eliminate the minimum clearance zone to combustible material.

* DEFINITIONOF NONCOMBUSTIBLEMATERIAL- Material which is not capable of being ignited and burned, such as

materials consisting entirely of, or a combination of, steel, iron, brick tile, concrete, slate,and plaster.

Clearances to Combustible Construction**:

Minimum of 12" from the sides and rear of grill must be maintained to adjacent vertical combustible

construction, above the counter top level. You should take in account that there is a large volume of heat, and

smoke will exhaust from the rear of the grill. This may discolor or damage unprotected areas (Fig. 03). Do not

install under unprotected combustible construction without using a fire safe ventilation system.

A 12" minimum clearance must be maintained under the counter top to combustible construction. The clearance

can be modified by a use of an insulated jacket.

8

INSTALLATION

LOCATING GRILL/BUILT-IN CLEARANCES

Clearances to Combustible Construction _

12" min.

12"min. _--

rol sserie

m( tot

J

grill

exhaust

................................................2G1/2" ..............................................A

"_ Bottom of

support flange

0000000

/2"

Maintain12" rain.

from combustible

construction

FIG. 03

_ DEFINITION OF COMBUSTIBLE MATERIAL-Any materials of a building structure or decorative structure made of

wood, compressed paper, plant fibers, vinyl/plastic or other materials that are capable of transferring heat or

being ignited and burned. Such material shall be considered combustible even though flame-proofed, fire-

retardant treated, or painted surface or plastered.

Important!

It is required that a minimum of (3)10 sq. inches of ventilation opening be provided for both the left and right

sides, as well as the back of enclosure (Fig. 04), in order to safely dissipate unburned gas vapors in the event of

a gas supply leak.

WARNING!

Note specific built-in enclosure ventilation requirements. See text and Fig. 05.

GENERAL

The grill is designed for easy placement into built-in masonry enclosures. For non-combustible applications the

grill drops into the opening shown in Fig. 04 and hangs from its side flanges. A deck is not required to support

it from the bottom. When using the insulated jacket in a combustible enclosure application, see the bottom of

Fig. 04. The insulation jacket assembly must be supported from the bottom by a ledge on each side and back or

a solid deck.

A carpenter's "spirit level" should be used to assure that the unit is level both front-to-back and side-to-side. If it

is not level, burner combustion may be erratic or the unit may not function efficiently for grease flow. If the floor

is uneven or has a decided slope, re-leveling may be required after each moving of a freestanding unit.

INSULATED JACKET:

WARNING!

Installing this product into a combustible enclosure without an insulated jacket could result in fire, property

damage and personal injury.

If the grill is to be placed into a combustible enclosure, an approved insulated jacket is necessary. Insulated

jackets are available from your dealer. Use only the DCS insulated jacket which has specifically been designed

and tested for this purpose. Review the detail drawing shown (Fig. 04) and take into account the provisions

shown for gas line hook-up clearance in the right rear corner. It is required that ventilation holes are provided in

the enclosure to eliminate the potential build-up of gas in the event of a gas leak. The supporting ledges or

deck must be level and flat and strong enough to support the grill and insulated jacket. The counter should also

be level.

INSTALLATION

BUILT-IN CONSTRUCTION DETAILS

grill

exhaust

q 3" (to non-combustible

/

/ construction /

minimum lid clearance)

/ 1 2" (to combustible

construct on)

support flange 10-1/16"

22-3/4 .... 3/4"

25-1/2 .......................................................

Standard layout for non-combustible enclosure:

NOTE: If using a backguard

apron or rear wall, locate

/ electrical service on the right

hand side for rotisserie motor

28-1/2"

connection

3" Min. for Lid Clearance

22-3/4"

Max.

4" x4"

opening

for gas

supply line

NOTE: See Fig.05

for ventilation notes.

opening for access

doors/drawers

(see Fig.05 and 06 for

ordering information)

Z_ WARNING!

If installing the grill into a non-combustible

enclosure, all combustible construction must still be

outside the 12 inch clearance zone. If your island is

made of stucco over the top of wooden studs, the

wood can not be inside the 12 inch clearance zone to

combustible, even though the stucco is what is

touching the grill area.

Layout for insulated jacket only - combustible enclosure:

NOTE: If using a backguard apron or rear

wall, locate electrical service on the right

hand side for rotisserie motor connection

34-7/8"

3" Min. for Lid

INSULATED JACKET

Size Part No.

30 70 8

4" x 4" opening

for gas supply line

k

35-1

Max. opening for access doors/drawers

(see Fig.05 and 06 for ordering

fl--J f information)

FIG.04

10

INSTALLATION

BUILT-IN CONSTRUCTION DETAILS

Access Drawers

Cutout dimensions

..... Vent

Optimal support

locations _

FIG. O5

NOTE: The cutout of each corner should be 90°angle in order for the access drawers

to fit properly.

_ Island installation to use minimum of 3 vents, 10 square inches per vent (typical).

×× For proper support and drawer operation, insure that support boards are installed

per Installation Guide instructions

MODEL NUMBER

ADR48 24-1/2"

ADR36 (Min,

ADR30 All

ADR24 Models)

A

(+O,-118)

46"

34"

28"

22"

B

(+118,-O)

20"

Access Doors

Cutout dimensions

Vent*

Cutout for Access Doors

FIG. 06

NOTE: The cutout of each corner should be 90°angle in order

for the access drawers to fit properly.

× Island installation to use minimum of 3 vents,

10 square inches per vent (typical).

MODEL NUMBER A B

(+O,-I18) (+I 18,-O)

ADN20x48 46" 20"

ADN20x36 34" 20"

ADN20x30 28" 20"

ADN20x24 22" 20"

Vent*

11

INSTALLATION

CART ASSEMBLY INSTRUCTIONS

IMPORTANT!

Read all instructions before you begin. Do not jump ahead or skip any step.

CAUTION!

Some parts have sharp edges; care must be taken when handling the various components to avoid injury. Please

read safety information provided in these instructions before beginning assembly. Wear gloves when handling.

Two or more people should work together to assemble the cart and grill head.

Note:

Avoid using side shelf to move cart. Pushor pull cart by grasping cornersofgrill head.

GETTING STARTED

Remove packaging.

Remove side shelf and side tray from inside and discard packing.

Contents Included:

Your cart is packaged in one box. The box contains your

30" grill cart and a universal hardware kit to be used for

BGB30-BQR grill installation and may contain extra

hardware for your convenience.

Contents Qty.

%j

30" Grill Cart

Side Shelf

Side Shelf Tray

Instruction

Contents Qty.

(_ Machine

philip screws 5

10-24Xl/2"

Bolt

1/4-20X 1/2"

I/4202 t

5

Keps Nut

1/4-20

Rubber 5

Bumper

Tools Required:

EyeGoggles

Work Gloves

Power Screwdriver or

Variable Speed Drill with

Phillips -tip #2 Attachment

10 mm Wrench or Socket

3/32"Allen Wrench

12

INSTALLATION

CART ASSEMBLY INSTRUCTIONS

1.

2.

3.

STEP I

Attach Side Shelf on the Right Side (left side is optional side burner location)

Attach shelf to right side of the cart using 1/4-20 nuts and bolts provided [leave out (1) bolt front side as shown

below].

Do not tighten bolts (finger tight only) until completing Step 4.

Install bumpers to the sides of the cart as shown below.

Install all 3bolts

(1/4-20Xl/2" bolts &

1/4-20 keps nut) in the

rear brackets asshown.

1.

2.

3.

4.

//

Install 2 bumpers on //"

each side. _ _ _" _/

®

Install 2 bolts (1/4-20X1/2" bolts &

1/4-20 keps nut) in the front

brackets as shown.

STEP 2

Grill Placement onto Cart (2 persons required)

Remove drip tray/pan for easier

handling. Place grill head on cart.

Slide back.

Ease over rear flange.

Secure with screws.

FIG. 07

FIG. 08 After drip tray/pan is removed, carefully

place grill head on cart (2 person minimum).

I

13

FIG. 09 Once grill rests on cart, slide grill to

rear of cart as shown.

INSTALLATION

CART ASSEMBLY INSTRUCTIONS

FIG. 10 Lift grill over rear flange of cart (be

aware of pinch points).

STEP 3

Front End Screw Installation

FIG. 11 Grill head should rest over rear cart

flange as shown above.

1. Install remaining (3) screws (10-24X1/2") in front of head to cart.

2. Slide drip tray/pan back into place. Move side shelf bars up and set

trays into place.

STEP 4

Bolt Installation

After head is in place, install the bolt (I/4-20 x 2") omitted from Step

I, and tighten all bolts on bracket. Tighten until sides are flush with

the trim only.

Note:

This bolt securesside bracket to grill head assembly for added side shelf

strength. Apply Loctite 242 (blue) to the first 3-4 threads prior to instal-

lation of this bolt

14

FIG. 12 Secure grill to rear of cart with (2)

phillips-head screws provided (10-24 x I/2").

FIG. 13 Secure grill to the front of the cart with Phillips-

head screws (provided).

FIG. 14 Front right side

INSTALLATION

CART ASSEMBLY INSTRUCTIONS

STEP 5

Side tray adjustment

1. Take the tray and place it onto the handle at a upright position. Make sure the tray sits snugly around the handle.

2. Then tighten the rest of the loose bolts that were not tightened in Step 1.

1.

2.

Side shelf adjustment

With extended use, the shelves may

become unleveled and need to be

readjusted.

In between the bracket where the handle

slides in is a 3/8" adjustment screw.

Grasping the handle as shown, raise up the

shelf and hold while with other hand using

a 3/32 allen wrench turn to the desired

level.

Adjustment

FIG.1S FIG. 16

FIG. 17

FIG. 18 FIG. 19

3. Slide drip tray/pan back into place.

4. Move side shelf bars up and set trays into place.

STEP 6

Gas Hookup- LP

Attach LP gas line connector hose

assembly (as shown in "LP Gas Hookup"

section - Use/Care Guide) and then

connect to LP tank as shown below.

FIG. 20 FIG. 21

15

INSTALLATION

GAS HOOK-UP

GAS REQUIREMENT

Verify the type of gas supply to be used, either natural or LP, and make sure the marking on the appliance rating

plate agrees with that of the supply. The rating plate is located underneath the unit bottom. Never connect an

unregulated gas line to the appliance. You must use the gas regulator provided with the unit, even if the supply

is controlled.

An installer-supplied gas shut-off valve must be installed in an easily accessible location. All installer supplied

parts must conform to local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA

70 or the Canadian Electrical Code, CSA C22.1, and the National Fuel Gas Code, ANSI Z223.1 or CAN/CGA-B149.1

Natural Gas Installation Code or CAN/CGA-B149.2 Propane Installation Code.

All pipe sealants must be an approved type and resistant to the actions of LPgases. Never use pipe sealant on

flare fittings. All gas connections should be made by a qualified technician and in accordance with local codes

and ordinances. In the absence of local codes, the installation must comply with the National Fuel Gas Code,

ANSIZ223.1. Gas conversion kits are available from the factory. When ordering gas conversion kits, have the

model number, and the type of gas (natural or LP) from your grill.

TOTAL GAS CONSUMPTION OF THE GRILL WITH ALL BURNERS ON HI:

BGB30-BQR - 64,000 Btu/hr

The appliance and its individual shut-off valve must be disconnected from the gas supply piping system during

any pressure testing of that system at test pressures in excess of 1/2 PSIG (3.5 kPa.) The appliance must be

isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure

testing of the gas supply piping system at test pressures equal to or less than 1/2 PSIG (3.5 kPa.). The installation

of this appliance must conform with local codes or, in the absence of local codes, with the National Fuel Gas

Code, ANSIZ223.1. Installation in Canada must be in accordance with the Standard Canl-b149.1 and/or .2

(installation code for gas burning appliances and

equipment) and local codes.

NATURAL GAS HOOK UP: (THIS TYPE OF

CONNECTION SHOULD BE PERFORMED BY A

CERTIFIED OR LICENSED TECHNICIAN ONLY.)

Connection: 1/2" NPT male with 3/8" flare adapter.

Operating pressure: 4.0" W.C. Supply pressure: 5" to

14" water column. If in excess of 14" W.C., a step down

regulator is required. Check with your local gas utility

company or local codes for instructions on installing

gas supply lines. Be sure to check on type and size of

run, and how deep to bury the line. If the gas line is

too small, the grill will not function properly. Any joint

sealant used must be an approved type and be

resistive to the actions of LP gases.

TO HOOK-UP THE FITTINGS SUPPLIED

WITH THE GRILL:

Assemble as shown (Fig. 22). Use threading compound

on male threads only. Do not use threading

compound on the male end of the 1/2" NPT to 3/8 flare

adapter. Use a second pipe wrench to hold the grill inlet

o O

\ Botomofunt/

Coup,n9

Threading compound "/_

mustb .... istanttoLP gas _ £_/_ 12!02,:'NPTx

_ -_/ Nipple

\ _ __ Regulator

1/2"NPTxS.O"\ tS_/_// 4.o,,w.c.

CloseNipple _/_

_../ Adapter 1/2" NPT

j to 3/8"flare fitting

Installer

supplied

shut-off

__ _ Do not put threading

valve must be easily

accessible _

compound on these

threads

_lnstallation must conform with local

codes or with the National Fuel Gas Code

ANSI Z223.1 or the CAN/CGA-B149.2

Propane Installation Code

FIG. 22 Natural Gas

pipe to avoid shifting any internal gas lines of the grill. Ensure that the regulator arrow points in the direction of

gas flow towards the unit, away from the supply. Do not forget to place the installer-supplied gas valve in an

accessible location.

LP GAS HOOK UP (TYPE 1 OR QCCl REGULATOR):

Grills orificed for use with LP gas come equipped with a high capacity hose/regulator assembly for connection to

a standard 20 lb. LP cylinder (Type 1). The LP tank is not included.

16

INSTALLATION

GAS HOOK-UP

Connection: I/2" NPT male with a 3/8" Flare adapter (included). LP Hose with a quick disconnect and fittings are

included. Operating pressure: 11.0" W.C.

CAUTION!

Before connecting LP tank to regulator, check that all grill burners, side burners, and rotisserie valves are in the OFF

position and open grill lid.

1.

2.

3.

4.

To connect the LP regulator/hose assembly to the tank/valve assembly, first make sure the main valve on the

tank is completely closed. Although the flow of gas is stopped when the Type 1 system is disconnected as part

of its safety feature, you should always turn off the LP tank main valve (Fig.23) after each use and during

transport of the tank or unit. Insert the regulator inlet into the tank valve and turn the black coupler clockwise

until the coupler tightens up. Do not overtighten the coupler. Turn the main tank valve on and turn the burner

control valves on the unit to the "HI" position for about 20 seconds to allow the air in the system to purge, turn

valves off and wait 5 minutes before attempting to light the burners.

To disconnect the coupler, first make sure the main tank valve is turned off. Grasp the coupler and turn counter

clockwise. The inlet will then disengage. Remove the inlet from the tank valve opening if it has not already

done so when it disengaged. Your local LP filling station should be equipped with the proper equipment to fill

your tank.

LP TANK REQUIREMENTS:

A dented or rusty LP tank may be hazardous and should be checked by your LP supplier. The cylinder that is

used must have a collar to protect the cylinder valve. Never use a cylinder with a damaged valve. Always

check for leaks after every LP tank change. The LP gas cylinder must be constructed and marked in accordance

with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT or CAN/CSA-B339) and

designed for use with a Type I system only. Do not change the regulator/hose assembly from that supplied with

the unit or attempt to use a Type I equipped regulator/hose assembly with a standard 510 POL tank/valve

assembly. The cylinder must be provided with a shut-off valve terminating in a LP gas supply cylinder valve

outlet specified, as applicable, for connection Type I. If the appliance is stored indoors, the cylinder must be

disconnected and removed from the appliance. Cylinders must be stored outdoors in a well-ventilated area

out of the reach of children.

Note:

When an LP unit is being directly connected to an LP house sys-

tem, you must follow the natural gas hook up guidelines. The

installer must provide the proper gas regulator to reduce the gas

flowto 11"W.C.

Note:

The Grill comes with the LP Regulator/Hose assembly installed at

the factory. The assembly, along with the entire Grill system, is

leak tested. Do not remove the Regulator/Hose assembly from

the Grill during installation.

WARNING :

Do not remove the Grill from the pallet until you are ready

to install.

ZZ

...........................ZZCZZIIT "---'=_'=' ..............................Z::::...........

\ 0 oo uoit

Type I Regulat ..............

\ / f Elbow 45°

Main Tank Valve _ _ tl 1/2" female

-_ _ I_ NPT x 3/8"male flare

_ _ (installed on the unit

20 lb. LP Tank I ..... - ..... [

........ I [ *Installation must conform with

_ local codes or with the National

j Fuel Gas Code ANSI Z223.1 or the

CAN/CGA-B149.2 Propane

Installation Code

FIG. 23 LP Gas

Do not place the Grill directly on the ground or any other flat surface without support. This will prevent

damaging the regulatorlhose assembly by the weight of the grill.

Check the hose, regulator and connectors for damage. Look for cracks, abrasions, brittleness, holes, dents

and nicks.

Do not attempt to remove, repair, or replace the Regulator/Hose assembly by yourself. It must be done by a

qualified licensed technician only.

17

INSTALLATION

GAS HOOK-UP

LP TANK RESTRAINT FOR BUILT-IN INSTALLATION

If the grill is to be installed in a Built-in application, then the grill must be installed in accordance with the

Built-in installation guidelines.

If you intend to operate your Built-in grill on LP gas utilizing a 201b Type cylinder, then the Built-in LPtank

restraint must be installed prior to initial use of the grill. If you do not have one please contact DCS Customer

Care at (888) 936-7872 for information on obtaining one.

The following steps will illustrate how to properly locate and install the LP tank restraint within the Built-in

enclosure.

NOTE:

The grill comes with the LP Regulator/Hose assembly installed at the factory. The assembly, along with the entire grill

system, is leak tested.

Do not remove the Regulator/Hose assembly from the grill during installation.

The maximum distance from the center

of the manifold cut out to the center of

the tank restraint is 18 inches.

Center of Tank Restraint must be

placed within this area to avoid

causing stress on the LP regulator

hose connection.

Center of manifold

cut out projected to

floor of the island.

FIG. 24

18

INSTALLATION

GAS HOOK-UP

STEP I

Place the tank restraint in the island (Fig. 25).

STEP 2

Locate the tank restraint in the island within the recommended area

(Fig. 24 and 26).

STEP 3

Once located, secure to the bottom of the island using all eight hole

locations provided on the restraint. Wood screws can be used for

wooden floors or I/4 inch diameter anchor screws or bolts may be

used if the floor is concrete or masonry (Fig. 27).

STEP 4

When secure, place the LP cylinder into the tank restraint making

sure to seat the tank all the way down, securely affixing the tank in

the restraint (Fig. 28).

STEP 5

Attach the regulator hose assembly and operate the grill normally as

described in the Use and Care manual (Fig. 29).

FIG. 25

FIG. 26

FIG. 27

FIG. 28

19

FIG. 29

La page charge ...

DCS BGB30-BQRN-70004A Le manuel du propriétaire

Ce manuel convient également à

DCS BGB30-BQRN-70004A Le manuel du propriétaire

dans d''autres langues

Documents connexes