LG ABUW12GL5S1.ENWTMEA Guide d'installation

P/NO.:MFL68065213

REV.00_190117

2

TIPS FOR SAVING ENERGY

ENGLISH

• Do not cool excessively indoors. This may be harmful to your health and may consume more elec-

tricity.

• Block sunlight with blinds or curtains while you are operating the air conditioner.

• Keep doors or windows closed tightly while you are operating the air conditioner.

• Adjust the direction of the air flow vertically or horizontally to circulate indoor air.

• Speed up the fan to cool or warm indoor air quickly, in a short period of time.

• Open windows regularly for ventilation as the indoor air quality may deteriorate if the air condition-

er is used for many hours.

• Clean the air filter once every 2 weeks. Dust and impurities collected in the air filter may block the

air flow or weaken the cooling / dehumidifying functions.

For your records

Staple your receipt to this page in case you need it to prove the date of purchase or for warranty

purposes. Write the model number and the serial number here:

Model number :

Serial number :

You can find them labeled on the side of each unit.

Dealer’s name :

Date of purchase :

Here are some tips that will help you minimize the power consumption when you use the air

conditioner. You can use your air conditioner more efficiently by referring to the instructions

below:

TIPS FOR SAVING ENERGY

1,MFL68500211,영어 2017. 6. 27. 오후 2:02 페이지 2

IMPORTANT SAFETY INSTRUCTIONS

3

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

Always comply with the following precautions to avoid dangerous situations and ensure peak

performance of your product

WARNING

It can result in serious injury or death when the directions are ignored

CAUTION

It can result in minor injury or product damage when the directions are ignored

WARNING

• Installation or repairs made by unqualified persons can result in hazards to you and others.

• Installation work must be performed in accordance with the National Electric Code by quali-

fied and authorized personnel only.

• The information contained in the manual is intended for use by a qualified service technician

familiar with safety procedures and equipped with the proper tools and test instruments.

• Failure to carefully read and follow all instructions in this manual can result in equipment mal-

function, property damage, personal injury and/or death.

Installation

• Always perform grounding. Otherwise, it may cause electrical shock.

• Don’t use a damaged power cable. Otherwise, it may cause a fire or electrical shock.

• For installation of the product, always contact the service center or a professional installation

agency. Otherwise, it may cause a fire, electrical shock, explosion or injury.

• Securely attach the electrical part cover to the indoor unit and the service panel to the outdoor

unit. If the electrical part cover of the indoor unit and the service panel of the outdoor unit are

not attached securely, it could result in a fire or electric shock due to dust, water, etc.

• Always install an earth leakage circuit breaker and a dedicated switching board. No installation

may cause a fire and electrical shock.

• Do not keep or use flammable gases or combustibles near the air conditioner. Otherwise, it

may cause a fire or the failure of product.

• Ensure that an installation frame of the outdoor unit is not damaged due to use for a long

time. It may cause injury or an accident.

• Do not disassemble or repair the product randomly. It will cause a fire or electrical shock.

• Use a vacuum pump or Inert (nitrogen) gas when doing leakage test or air purge. Do not com-

press air or Oxygen and do not use Flammable gases. Otherwise, it may cause fire or explo-

sion. There is the risk of death, injury, fire or explosion.

• Do not install the product at a place that there is concern of falling down. Otherwise, it may

result in personal injury.

• Use caution when unpacking and installing. Sharp edges may cause injury.

• Do not turn on the breaker or power under condition that front panel, cabinet, top cover, con-

trol box cover are removed or opened. Otherwise, it may cause fire, electric shock, explosion

or death.

!

1,MFL68500211,영어 2017. 6. 27. 오후 2:02 페이지 3

4

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

Operation

• Do not share the outlet with other appliances. It will cause an electric shock or a fire due to

heat generation.

• Do not use the damaged power cable. Otherwise, it may cause a fire or electrical shock.

• Do not modify or extend the power cable randomly. Otherwise, it may cause a fire or electri-

cal shock.

• Take care so that the power cable may not be pulled during operation. Otherwise, it may

cause a fire or electrical shock.

• Turn off the unit if strange sounds, smell, or smoke comes from it. Otherwise, it may cause

electrical shock or a fire.

• Keep the flames away. Otherwise, it may cause a fire.

• Do not use the power cable near the heating tools. Otherwise, it may cause a fire and electri-

cal shock.

• Do not open the suction inlet of the indoor/outdoor unit during operation. Otherwise, it may

electrical shock and failure.

• Do not allow water to run into electrical parts. Otherwise, it may cause the failure of machine

or electrical shock.

• Do not touch the power cable with wet hands. It may cause electric shock and damage.

• Never touch the metal parts of the unit when removing the filter. They are sharp and may

cause injury.

• Do not step on the indoor/outdoor unit and do not put anything on it. It may cause an injury

through dropping of the unit or falling down.

• Do not place a heavy object on the power cable. Otherwise, it may cause a fire or electrical

shock.

• When the product is submerged into water, always contact the service center. Otherwise, it

may cause a fire or electrical shock.

• Take care so that children may not step on the outdoor unit. Otherwise, children may be seri-

ously injured due to falling down.

1,MFL68500211,영어 2017. 6. 27. 오후 2:02 페이지 4

IMPORTANT SAFETY INSTRUCTIONS

5

ENGLISH

CAUTION

Installation

• Install the drain hose to ensure that drain can be securely done. Otherwise, it may cause

water leakage.

• Install the product so that the noise or hot wind from the outdoor unit may not cause any

damage to the neighbors. Otherwise, it may cause dispute with the neighbors.

• Always inspect gas leakage after the installation and repair of product. Otherwise, it may

cause the failure of product.

• Keep level parallel in installing the product. Otherwise, it may cause vibration or water leak-

age.

Operation

• Avoid excessive cooling and perform ventilation sometimes. Otherwise, it may do harm to

your health.

• Use a soft cloth to clean. Do not use wax, thinner, or a strong detergent. The appearance of

the air conditioner may deteriorate, change color, or develop surface flaws.

• Do not use an appliance for special purposes such as preserving animals vegetables, preci-

sion machine, or art articles. Otherwise, it may damage your properties.

• Do not place obstacles around the flow inlet or outlet. Otherwise, it may cause the failure of

appliance or an accident.

!

1,MFL68500211,영어 2017. 6. 27. 오후 2:02 페이지 5

1,MFL68500211,영어 2017. 6. 27. 오후 2:02 페이지 6

6

TABLE OF CONTENTS

ENGLISH

2 TIPS FOR SAVING ENER-

GY

3 IMPORTANT SAFETY

INSTRUCTIONS

7 INSTALLATION OF OUT-

DOOR UNIT

9 WIRING CONNECTION

9 Electrical Wiring

10 Connecting Cables between Indoor Unit

and Outdoor Unit

13 Connecting the cable to Outdoor Unit

14 CONNECTING PIPES

14 Preparation of Piping

15 Connecting the pipes to the Outdoor

unit

16 Forming the Piping

17 LEAKAGE TEST AND

EVACUATION

17 Preparation

17 Leakage test

18 Evacuation

19 TEST RUNNING

21 INSTALLATION GUIDE AT

THE SEASIDE

TABLE OF CONTENTS

INSTALLATION OF OUTDOOR UNIT

7

ENGLISH

- If an awning is built over the unit to prevent direct sunlight or rain exposure, make sure that

heat radiation from the condenser is not restricted.

- Ensure that the spaces indicated by arrows around front, back and side of the unit.

- Do not place animals and plants in the path of the warm air.

- Take the air conditioner weight into account and select a place where noise and vibration are

minimum.

- Select a place so that the warm air and noise from the air conditioner do not disturb neighbors.

More than

300 mm

Fence or

obstacles

More than 700 mm

More than 600 mm

More thanMore than

300mm300mm

More than

300 mm

Sunroof

Unit : mm

Installation Places

INSTALLATION OF OUTDOOR UNIT

1,MFL68500211,영어 2017. 6. 27. 오후 2:02 페이지 7

1,MFL68500211,영어 2017. 6. 27. 오후 2:02 페이지 8

8

INSTALLATION OF OUTDOOR UNIT

ENGLISH

MODEL

Pipe Size Length A (m) Elevation B (m)

Additional

Refrigerant (g/m)

Gas Liquid

Standard

Max.

Standard

Max.

Ø9.52(3/8) Ø6.35(1/4)ABUW12GL5S1

Free Joint Single Outdoor

Piping length and the elevation

Outdoor unit

Indoor unit

A

B

Outdoor unit

Indoor unit

A

B

If installed tube is shorter than Standard length, additional charging is not necessary.

Additional Refrigerant = (Max. Length - Standard Length) x Additional refrigerant (g)

7.5 15 5

7.5 20

1,MFL68500211,영어 2017. 6. 27. 오후 2:02 페이지 9

WIRING CONNECTION

9

ENGLISH

Electrical Wiring

Perform the electrical wiring work according

to the electrical wiring connection.

- All wiring must comply with local require-

ments.

- Select a power source that is capable of sup-

plying the current required by the air condi-

tioner.

- Use a recognized ELCB(Electric Leakage

Circuit Breaker) between the power source

and the unit. A disconnection device to ade-

quately disconnect all supply lines must be

ﬁtted.

- Model of circuit breaker recommended by

authorized personnel only

Outdoor

Indoor

Main

power source

Switch box

ELCB

WIRING CONNECTION

Model Phase(Ø) ELCB

ABUW12GL5S1 1 15

10

WIRING CONNECTION

ENGLISH

Connecting Cables between Indoor Unit and Outdoor Unit

Outdoor

unit

Indoor

unit

1

2

3

1

2

3

The power cable connected to the outdoor unit should be complied with IEC 60245 or HD 22.4 S4

(This equipment shall be provided with a cable set complying with the national regulation.)

NORMAL CROSS-SECTIONAL AREA

CAUTION

!

1 Phase(Ø)

GN/YL

20 mm

35±5 mm

10±3 mm

Model Phase(Ø) Area(mm²)

ABUW12GL5S1

1 2.5

1,MFL68500211,영어 2017. 6. 27. 오후 2:02 페이지 10

WIRING CONNECTION

11

ENGLISH

The connecting cable connected to the outdoor unit should be complied with IEC 60245 or

HD 22.4 S4 (This equipment shall be provided with a cable set complying with the national

regulation.)

If the supply cable is damaged, it must be replaced by a special cable or assembly availible

from the manufacturer of its service agent.

When the connection

line between the

indoor unit and out-

dooor unit is over 40

m, connect the

telecommunication

line and power line

separately.

20 mm

GN/YL

35±5 mm

10±3 mm

NORMAL CROSS-SECTIONAL AREA

Model Phase(Ø) Area(mm²)

ABUW12GL5S1

1 0.75

CAUTION

!

1,MFL68500211,영어 2017. 6. 27. 오후 2:02 페이지 11

12

WIRING CONNECTION

ENGLISH

Use round pressure terminals for connections to the power terminal block.

When none are available, follow the instructions below.

- Do not connect wiring of different thicknesses to the power terminal block. (Slack in the power

wiring may cause abnormal heat.)

- When connecting wiring which is the same thickness, do as shown in the figure below.

- For wiring, use the designated power wire and connect firmly, then secure to prevent outside

pressure being exerted on the terminal block.

- Use an appropriate screwdriver for tightening the terinal screws. A screwdriver with a small

head will strip the head and make proper tighterning impossible.

- Over-tightening the terminal screws may break them.

Round pressure terminal

Power wire

Connect same thickness

wiring to both sides.

It is forbidden to connect

two to one side.

It is forbidden to

connect wiring of

different thicknesses.

Precautions when laying power wiring

1,MFL68500211,영어 2017. 6. 27. 오후 2:02 페이지 12

1,MFL68500211,영어 2017. 6. 27. 오후 2:02 페이지 13

WIRING CONNECTION

13

ENGLISH

Connecting the cable to Outdoor Unit

Remove the side panel for wiring connection.

Use the cord clamp to ﬁx the cable.

Earthing work

- Connect the cable of diameter more to the earthing terminal provided in the control box and do

earthing.

Tubing Cover

Power cord

Power

connecting cable

Power cord

Power

connecting cable

Tubing cover

• The circuit diagram is not subject to change without notice.

• Be sure to connect wires according to the wiring diagram.

• Connect the wires ﬁrmly, so that not to be pulled out easily.

• Connect the wires according to color codes by referring the wiring diagram.

• The Power cable connected to the unit should be selected according to the following

speciﬁcations.

CAUTION

!

14

CONNECTING PIPES

ENGLISH

Preparation of Piping

Main cause of gas leakage is defect in flaring work. Carry out correct flaring work in the following

procedure.

Cut the pipes and the cable

- Use the piping kit accessory or the pipes pur-

chased locally.

- Measure the distance between the indoor

and the outdoor unit.

- Cut the pipes a little longer than measured

distance.

- Cut the cable 1.5 m longer than the pipe

length.

Burrs removal

- Completely remove all burrs from the cut

cross section of pipe/tube.

- Put the end of the copper tube/pipe in a

downward direction as you remove burrs in

order to avoid dropping burrs into the tubing.

Putting nut on

- Remove flare nuts attached to indoor and

outdoor unit, then put them on pipe/tube

having completed burr removal.

(not possible to put them on after flaring

work)

Flaring work

- Carry out flaring work using flaring tool as

shown below.

Firmly hold copper pipe in a bar in the

dimension shown in the table below.

Check

- Compare the flared work with figure below.

- If flare is noted to be defective, cut off the

flared section and do flaring work again.

Copper

tube

90

Slanted Uneven Rough

Pipe

Reamer

Point down

Flare nut

Copper tube

Bar

Copper pipe

Clamp handle

Red arrow mark

Cone

Yoke

Handle

Bar

"A"

Inclined

Inside is shining without scratches.

Smooth all round

Even length

all round

Surface

damaged

Cracked Uneven

thickness

= Improper ﬂaring =

Outside diameter

A

mm inch mm

Ø 6.35 1/4 1.1~1.3

Ø 9.52 3/8 1.5~1.7

Ø 12.7 1/2 1.6~1.8

Ø 15.88 5/8 1.6~1.8

Ø 19.05 3/4 1.9~2.1

CONNECTING PIPES

1,MFL68500211,영어 2017. 6. 27. 오후 2:02 페이지 14

CONNECTING PIPES

15

ENGLISH

Connecting the pipes to the Outdoor unit

Align the center of the piping and sufficiently

tighten the flare nut by hand.

Finally, tighten the flare nut with torque

wrench until the wrench clicks.

- When tightening the flare nut with torque

wrench, ensure the direction for tightening

follows the arrow on the wrench.

Torque

wrench

Contin

-uous

Torque

wrench

Gas side piping

Liquid side piping

Drain hose

Connecting wire

h When tighten the pipe, hold the haxago-

nal body.

Continuous

TorqueTorque

wrenchwrench

Torque

wrench

h When tighten the pipe, hold the haxago-

nal body.

Torque

wrench

h When tighten the pipe, hold the haxago-

nal body.

Outside diameter

Torque

mm inch N·m

Ø 6.35 1/4 16±2

Ø 9.52 3/8 38±4

Ø 12.7 1/2 55±6

Ø 15.88 5/8 75±7

Ø 19.05 3/4 110±10

Preventing foreign objects from entering

- Plug the pipe through-holes with putty or

insulation material(procured locally)to stop up

all gaps.

Torque

wrench

Torque wrech

Liquid side piping

(Smaller diameter)

Gas side piping

(Bigger diameter)

h When tighten the pipe, hold the haxago-

nal body.

1,MFL68500211,영어 2017. 6. 27. 오후 2:03 페이지 15

16

CONNECTING PIPES

ENGLISH

Forming the Piping

Form the piping by wrapping the connecting

portion of the indoor unit with insulation mate-

rial and secure it with two kinds of vinyl tape.

- If you want to connect an additional drain

hose, the end of the drain outlet should be

routed above the ground. Secure the drain

hose appropriately.

In cases where the outdoor unit is installed

below the indoor unit perform the following.

1 Tape the piping, drain hose and connecting

cable from down to up.

2 Secure the tapped piping along the exterior

wall using saddle or equivalent.

In cases where the Outdoor unit is installed

above the Indoor unit perform the following.

1 Tape the piping and connecting cable from

down to up.

2 Secure the taped piping along the exterior

wall. Form a trap to prevent water entering

the room.

3 Fix the piping onto the wall by saddle or

equivalent.

• Trap is required to prevent water from entering

into electrical parts.

Taping

Drain hose

Pipings

Connecting

cable

Power supply

cord

Plastic

band

Plastic

band

Seal a small

opening around

the pipings with

gum type sealer.

Seal a small

opening around

the pipings with

gum type sealant.

Trap

TrapTrapTrap

Seal a small opening Seal a small opening

around the pipings around the pipings

with gum type sealer.with gum type sealer.

Seal a small opening

around the pipings

with gum type sealant.

1,MFL68500211,영어 2017. 6. 27. 오후 2:03 페이지 16

LEAKAGE TEST AND EVACUATION

17

ENGLISH

Preparation

Check that each tube(both liquid and gas side

tubes) between the indoor and outdoor units

have been properly connected and all wiring

for the test run has been completed. Remove

the service valve caps from both the gas and

the liquid side on the outdoor unit. Check that

both the liquid and the gas side service valves

on the outdoor unit are kept closed at this

stage.

Leakage test

Connect the manifold valve(with pressure

gauges) and dry nitrogen gas cylinder to this

service port with charge hoses.

CAUTION

Be sure to use a manifold valve for leakage

test. If it is not available, use a stop valve for

this purpose. The "Hi" knob of the manifold

valve must always be kept close.

- Pressurize the system to no more than

3.8 Mpa with dry nitrogen gas and close

the cylinder valve when the gauge read-

ing reached 3.8 MPa Next, test for leaks

with liquid soap.

!

CAUTION

To avoid nitrogen entering the refrigerant

system in a liquid state, the top of the

cylinder must be higher than its bottom

when you pressurize the system. Usually,

the cylinder is used in a vertical standing

position.

!

- Do a leakage test of all joints of the

tubing(both indoor and outdoor) and both gas

and liquid side service valves.

Bubbles indicate a leak. Be sure to wipe off

the soap with a clean cloth.

- After the system is found to be free of leaks,

relieve the nitrogen pressure by loosening

the charge hose connector at the nitrogen

cylinder. When the system pressure is

reduced to normal, disconnect the hose from

the cylinder.

Air and moisture remaining in the refrigerant

system have undesirable effects as indicated

below.

- Pressure in the system rises.

- Operating current rises.

- Cooling(or heating) efficiency drops.

- Moisture in the refrigerant circuit may freeze

and block capillary tubing.

- Water may lead to corrosion of parts in the

refrigeration system.

Therefore, the indoor/outdoor unit and con-

necting tube must be checked for leak tight,

and vacuumed to remove incondensible gas

and moisture in the system.

Charge hose

Indoor unit

Outdoor unit

Manifold valve

Pressure

gauge

Nitrogen gas

cylinder(in vertical

standing position)

Lo Hi

LEAKAGE TEST AND EVACUATION

1,MFL68500211,영어 2017. 6. 27. 오후 2:03 페이지 17

18

LEAKAGE TEST AND EVACUATION

ENGLISH

- When the desired vacuum is reached, close

the "Lo and Hi" knob of the manifold valve

and stop the vacuum pump.

Required time for evacuation when 30 gal/h

vacuum pump is used

If tubing length is

less than 10 m(33 ft)

If tubing length is

longer than 10 m(33

ft)

30 min. or more 60 min. or more

0.07 kPa or less

- Replace the valve caps at both gas and liquid

side service valves and fasten them tight.

This completes air purging with a vacuum pump.

The air conditioner is now ready to test run.

- With a service valve wrench, turn the valve

stem of liquid side valve counter-clockwise to

fully open the valve.

- Turn the valve stem of gas side valve counter-

clockwise to fully open the valve.

- Loosen the charge hose connected to the gas

side service port slightly to release the pressure,

then remove the hose.

- Replace the flare nut and its bonnet on the gas

side service port and fasten the flare nut secure-

ly with an adjustable wrench. This process is

very important to prevent leakage from the sys-

tem.

Indoor unit

Outdoor unit

Lo Hi

Manifold valve

Vacuum pump

Open

Pressure

gauge

Finishing the Job

Evacuation

- Connect the charge hose end described in

the preceding steps to the vacuum pump to

evacuate the tubing and indoor unit.

Confirm the "Lo and Hi" knob of the manifold

valve is open. Then, run the vacuum pump.

The operation time for evacuation varies with

tubing length and capacity of the pump. The

following table shows the time required for

evacuation.

1,MFL68500211,영어 2017. 6. 27. 오후 2:03 페이지 18

TEST RUNNING

19

ENGLISH

- The initial power supply must provide at least 90 % of the rated voltage.

Otherwise, the air conditioner should not be operated.

- The test run is started by pressing the room temperature checking button and down timer but-

ton for 3 seconds at the same time.

- To cancel the test run, press any button.

CHECK THE FOLLOWING ITEMS WHEN INSTALLATION IS COMPLETE

- After completing work, be sure to measure and record trial run properties, and store measured

data, etc.

- Measuring items are room temperature, outside temperature, suction temperature, blow out

temperature, wind velocity, wind volume, voltage, current, presence of abnormal vibration and

noise, operating pressure, piping temperature, compressive pressure.

- As to the structure and appearance, check following items.

• Connect the power supply cable to the independent power supply.

- Circuit breaker is required.

• Operate the unit for fifteen minutes or more.

Precautions In Test Running

Connection of power supply

Evaluation of the performance

CAUTION

For test run, carry out the cooling operation firstly even during heating season. If heating operation

is carried out firstly, it leads to the trouble of compressor. Then attention must be paid.

Carry out the test run more than 5 minutes without fail.

(Test run will be cancelled 18 minutes later automatically)

!

□Is the circulation of air adequate?

□Is the draining smooth?

□Is the heat insulation complete

(refrigerant and drain piping)?

□Is there any leakage of refrigerant?

□Is the remote controller switch operated?

□Is there any faulty wiring?

□Are not terminal screws loosened?

M4......118 N·cm {12 kgf·cm}

M5......196 N·cm {20 kgf·cm}

M6......245 N·cm {25 kgf·cm}

M8......588 N·cm {60 kgf·cm}

- Measure the temperature of the intake and

discharge air.

- Ensure the difference between the intake

temperature and the discharge one is more

than 8 °C (Cooling) or reversely (Heating).

Thermometer

TEST RUNNING

1,MFL68500211,영어 2017. 6. 27. 오후 2:03 페이지 19

20

TEST RUNNING

ENGLISH

CAUTION

After the confirmation of the above conditions, prepare the wiring as follows:

1 Never fail to have an individual power specialized for the air conditioner. As for the

method of wiring, be guided by the circuit diagram pasted on the inside of control box

cover.

2 Provide a circuit breaker switch between power source and the unit.

3 The screw which fasten the wiring in the casing of electrical fittings are liable to come

loose from vibrations to which the unit is subjected during the course of transportation.

Check them and make sure that they are all tightly fastened. (If they are loose, it could

give rise to burn-out of the wires.)

4 Specification of power source

5 Confirm that electrical capacity is sufficient.

6 Be sure that the starting voltage is maintained at more than 90 percent of the rated volt-

age marked on the name plate.

7 Confirm that the cable thickness is as specified in the power sources specification.

(Particularly note the relation between cable length and thickness.)

8 Never fail to equip a leakage breaker where it is wet or moist.

9 The following troubles would be caused by voltage drop-down.

- Vibration of a magnetic switch, damage on the contact point there of fuse breaking, dis-

turbance to the normal function of a overload protection device.

- Proper starting power is not given to the compressor.

!

1,MFL68500211,영어 2017. 6. 27. 오후 2:03 페이지 20

La page charge ...

LG ABUW12GL5S1.ENWTMEA Guide d'installation

Ce manuel convient également à

LG ABUW12GL5S1.ENWTMEA Guide d'installation

dans d''autres langues

Documents connexes

Autres documents