Electrolux GA553IF Manuel utilisateur

user manual

notice d'utilisation

benutzerinformation

istruzioni per l’uso

Dishwasher

Lave-vaisselle

Geschirrspülmaschine

Lavastoviglie

GA553IF

Electrolux. Thinking of you.

Share more of our thinking at www.electrolux.com

Contents

Safety information 2

Product description 3

Control panel 4

Use of the appliance 5

Setting the water softener 6

Use of dishwasher salt 6

Use of rinse aid 7

Loading cutlery and dishes 8

Use of detergent 12

Multitab function 13

Setting and starting a washing programme

14

Washing programmes 15

Care and cleaning 15

What to do if… 17

Technical data 18

Installation 19

Water connection 20

Electrical connection 21

Environment concerns 21

Subject to change without notice

Safety information

For your safety and correct operation of

the appliance, read this manual carefully

before installation and use. Always keep

these instructions with the appliance

even if you move or sell it. Users must

fully know the operation and safety fea-

tures of the appliance.

Correct use

• The appliance is designed exclusively for

domestic use.

• Only use the appliance to clean household

utensils that are applicable for dishwash-

ers.

• Do not put solvents in the appliance. Risk

of explosion.

• Put the knives and all items with sharp

points in the cutlery basket with their

points down. If not, put in a horizontal po-

sition in the upper basket.

• Use only branded products for dishwash-

ers (detergent, salt, rinse aid).

• If you open the door while the appliance is

in operation, hot steam can escape. Risk

of skin burns.

•Do not remove dishes from the dishwasher

before the end of the washing programme.

• When the washing programme is comple-

ted, disconnect the mains plug from the

mains socket and close the water tap.

• Only an authorised service engineer can

repair this appliance. Use only original

spare parts.

• Do not do repairs yourself to prevent injury

and damage to the appliance. Always con-

tact your local Service Force Centre.

General safety

• Persons (including children) with reduced

physical sensory, mental capabilities or

lack of experience and knowledge must

not use the appliance. They must have su-

pervision or instruction for the operation of

the appliance by a person responsible for

their safety.

• Obey the safety instructions from the man-

ufacturer of the dishwasher detergent to

prevent burns to eyes, mouth and throat.

• Do not drink the water from the dishwash-

er. Detergent residues can stay in your ap-

pliance.

• Always close the door when you do not

use the appliance to prevent injury and not

to stumble over the open door.

• Do not sit or stand on the open door.

Child safety

• Only adults can use this appliance. Chil-

dren must get supervision to make sure

that they do not play with the appliance.

• Keep all the packaging away from children.

There is a risk of suffocation.

• Keep all detergents in a safe area. Do not

let children touch the detergents.

• Keep children away from the appliance

when the door is open.

2 electrolux

Installation

• Make sure that the appliance is not dam-

aged because of transport. Do not con-

nect a damaged appliance. If necessary,

contact the supplier.

• Remove all packaging before first use.

• A qualified and competent person must do

the electrical installation.

• A qualified and competent person must do

the plumbing installation.

• Do not change the specifications or modify

this product. Risk of injury and damage to

the appliance.

• Do not use the appliance:

– if the mains cable or water hoses are

damaged,

– if the control panel, worktop or plinth

area are damaged, that you can get ac-

cess to the inner side of the appliance.

Contact your local Service Force Centre.

• Do not drill into the sides of the appliance

to prevent damage to hydraulic and elec-

trical components.

Warning! Carefully obey the

instructions for electrical and water

connections.

Product description

1 Ceiling spray arm

2 Upper basket

3 Upper spray arm

4 Filters

5 Lower spray arm

6 Detergent dispenser

7 Rinse aid dispenser

8 Rating plate

9 Salt container

electrolux 3

Control panel

6

1 On/off button

2 Programme button

3

Multitab button

4

Half-load button

5 Indicator lights

6 Function buttons

Indicator lights

Wash The indicator light comes on when the washing

phase or the rinsing phase operates.

Dry The indicator light comes on when the drying

phase operates.

End-of-programme The indicator light comes on when the washing

programme is completed. Auxiliary functions:

• Level of the water softener.

• Activation/deactivation of the rinse aid dispens-

er.

• An alarm if the appliance has a malfunction.

Rinse aid

1)

The indicator light comes on when it is necessary

to fill the rinse aid. Refer to the chapter 'Use of

rinse aid'.

4 electrolux

Indicator lights

Salt

1)

The indicator light comes on when it is necessary

to fill the salt container. Refer to the chapter 'Use

of dishwasher salt'.

After you fill the container, the salt indicator light

can continue to stay on for some hours. This does

not have an unwanted effect on the operation of

the appliance.

1) When the salt and/or rinse aid containers are empty, the related indicator lights do not come on while

a washing programme operates.

Programme button

With this button you can select the washing

programme. Press the button until the indi-

cator light of the necessary programme

comes on. Refer to 'Washing programmes'

chapter for more data about the washing

programmes.

Multitab button

Press this button to activate/deactivate the

multitab function. Refer to the chapter 'Mul-

titab function'.

Half-load button

Important! Set the Half-load option before

the start of a washing programme. You

cannot set the option when a washing

programme operates. If it is necessary to set

the Half-load option, cancel the washing

programme.

The Half-load option is not available for all

washing programmes. Refer to the chapter

'Washing programmes'.

• Load dishes in the upper and lower bas-

ket.

• Decrease the detergent dosage when you

use the Half-load option.

• Press the Half-load button to set the op-

tion.

– The Half-load indicator light comes on,

when the Half-load option is available.

With the Half-load option the time dura-

tion and the consumption of water and

energy are reduced.

Function buttons

Use the function buttons for these opera-

tions:

• To set the water softener. Refer to the

chapter 'Setting the water softener'.

• To deactivate/activate the rinse aid dis-

penser, when multitab function is active.

Refer to the chapter 'Multitab function'.

• To cancel the washing programme in pro-

gress.

Setting mode

Press the on/off button, if the programme

button indicator light and the end-of-pro-

gramme indicator light are on, the appliance

is in setting mode.

The appliance must be in setting mode for

these operations:

– To set a washing programme.

– To set the water softener level.

– To deactivate/activate the rinse aid dis-

penser.

Press the on/off button, the appliance is not

in setting mode if:

• the programme button indicator light is on,

• a programme indicator light is on,

• 1 or 2 phase indicator lights are on.

Cancel the programme to go back to the

setting mode. Refer to the chapter 'Setting

and starting a washing programme'.

Use of the appliance

Refer to the following instructions for each

step of procedure:

1. Make a check if the water softener level

is correct for the water hardness in your

area. If necessary set the water softener.

2. Fill the salt container with dishwasher salt.

3. Fill the rinse aid dispenser with rinse aid.

4. Load cutlery and dishes into the dish-

washer.

electrolux 5

5. Set the correct washing programme for

the type of load and soil.

6. Fill the detergent dispenser with the cor-

rect quantity of detergent.

7. Start the washing programme.

If you use combi detergent tablets ('3 in

1', '4 in 1', '5 in 1', etc.), refer to the

chapter 'Multitab function'.

Setting the water softener

The water softener removes minerals and

salts from the water supply. Minerals and

salts can have bad effect on the operation of

the appliance.

Water hardness is measured in equivalent

scales:

• German degrees (dH°).

• French degrees (°TH).

• mmol/l (millimol per litre - international unit

for the hardness of water).

•Clarke.

Adjust the water softener to the water hard-

ness in your area. If necessary, contact your

local water authority.

Water hardness

setting

°dH °TH mmol/l Clarke

51 - 70 91 - 125 9,1 - 12,5 64 - 88 10

43 - 50 76 - 90 7,6 - 9,0 53 - 63 9

37 - 42 65 - 75 6,5 - 7,5 46 - 52 8

29 - 36 51 - 64 5,1 - 6,4 36 - 45 7

23 - 28 40 - 50 4,0 - 5,0 28 - 35 6

19 - 22 33 - 39 3,3 - 3,9 23 - 27 5

15 - 18 26 - 32 2,6 - 3,2 18 - 22 4

11 - 14 19 - 25 1,9 - 2,5 13 - 17 3

4 - 10 7 - 18 0,7 - 1,8 5 - 12 2

< 4 < 7 < 0,7 < 5

1

1)

1) No use of salt required.

The water softener is set at the fac-

tory at level 5.

1. Switch on the appliance.

2. Make sure that the appliance is in setting

mode.

3. Press and hold function buttons B and C

until the indicator lights for function but-

tons A, B and C start to flash.

4. Release function buttons B and C.

5. Press function button A.

– The indicator light for function button A

continues to flash.

– The indicator lights for function buttons

B and C go off.

– The end-indicator-light starts to flash.

The setting function of the water softener

is activated.

The end-of-programme indicator light

flashes to show the level of the water

softener. The pause is approximately 5

seconds.

Example: 5 flashes, pause, 5 flashes,

pause, etc. = level 5

6. Press the function button A one time to

increase the water softener level by one

step.

7. Press the on/off button to save the oper-

ation.

Use of dishwasher salt

Caution! Only use dishwashers salt.

Types of salt that are not applicable for

dishwashers cause damage to the water

softener.

Caution! Grains of salt and salty water

on the bottom of the appliance can

cause corrosion. Fill the appliance with

salt before you start a washing

programme to prevent corrosion.

6 electrolux

Do these steps to fill the salt container:

1. Turn the cap anticlockwise to open the

salt container.

2. Fill the salt container with 1 litre of water

(only the first operation).

3. Fill the salt container with salt.

4. Remove the salt around the opening of

the salt container.

5. Turn the cap clockwise to close the salt

container.

It is normal that water overflows from the

salt container when you fill it with salt.

When you set the water softener to level 1,

the salt indicator light does not stay on.

Use of rinse aid

Caution! Only use branded rinse aid for

dishwashers.

Do not fill the rinse aid dispenser with

other products (e.g. dishwasher clean-

ing agent, liquid detergent). This can

cause damage to the appliance.

Rinse aid makes it possible to dry the

dishes without streaks and stains.

Rinse aid is automatically added during

the last rinsing phase.

Do these steps to fill the rinse aid dispenser:

1. Press the release button (A) to open the

rinse aid dispenser.

2. Fill the rinse aid dispenser with rinse aid.

The mark 'max.' shows the maximum

level.

3. Remove the spilled rinse aid with an ab-

sorbent cloth to prevent too much foam

during the subsequent washing pro-

gramme.

4. Close the rinse aid dispenser.

Adjusting the rinse aid dosage

The rinse aid is set at the factory at position

4.

You can set the rinse aid dosage between

position 1 (lowest dosage) and position 6

(highest dosage).

electrolux 7

1. Turn the rinse aid dial to increase or de-

crease the dosage.

– Increase the dosage if there are water

droplets or limescale on the dishes.

– Decrease the dosage if there are

streaks, whitish stains or bluish layers

on the dishes.

Loading cutlery and dishes

Helpful hints and tips

Caution! Only use the appliance for

household utensils that are applicable

for dishwashers.

Do not use the appliance to clean objects

that can absorb water (sponges, household

cloths, etc.).

• Before you load cutlery and dishes, do

these steps:

– Remove all food remainings and debris.

– Make burnt, remaining food in pans soft.

• While you load cutlery and dishes, do

these steps:

– Load hollow items (e.g. cups, glasses

and pans) with the opening down.

– Make sure that water does not collect in

the container or in a deep base.

– Make sure that cutlery and dishes do not

lie inside one another.

– Make sure that cutlery and dishes do not

cover other cutlery and dishes.

– Make sure that glasses do not touch

other glasses.

– Put small objects in the cutlery basket.

• Plastic items and pans with non-stick

coatings can keep water droplets. Plastic

items do not dry as well as porcelain and

steel items.

• Put light items in the upper basket. Make

sure that the items do not move.

Caution! Make sure that the spray arms

can move freely before you start a

washing programme.

Warning! Always close the door after

you load or unload the appliance. An

open door can be dangerous.

Lower basket

Put saucepans, lids, plates, salad bowls and

cutlery in the lower basket. Put service dishes

in the front part of the basket.

The rows of prongs in the rear part of the

basket can be flat to load pots, pans, bowls

and deep dishes.

1. Hold the two rows of prongs on the right

side at the rear part of the basket.

2. Lift the rows of prongs out of the guides.

3. Fold the rows of prongs in.

8 electrolux

1. Hold the two rows of prongs on the left

side at the rear part of the basket.

2. Lift the rows of prongs out of the guides.

3. Fold the rows of prongs in.

You can adjust the width of the left row of

prongs.

1. Hold the row of prongs at the rear part of

the basket.

2. Pull the row of prongs until it disengages.

3. Push the row of prongs out of the guide.

4. Put the row of prongs into the other

guide.

5. Push the row of prongs down until it en-

gages in position.

Cutlery basket

Warning! Do not put long-bladed knives

in a vertical position in the cutlery basket.

Arrange long and sharp cutlery

horizontally in the upper basket. Be

careful with sharp items.

Put forks and spoons with the handles down.

Put knives with the handles up.

If the points of the knives come out from the

bottom of the basket, there is a blockage of

the lower spray arm. Put knives with the han-

dles down.

Mix spoons with other cutlery to prevent

them to bond together.

Lower the handle of the cutlery basket to put

the cutlery in the basket.

Use the cutlery grids. If the dimensions of the

cutlery prevent use of the cutlery grids, you

can easily hide them.

electrolux 9

The cutlery basket has two parts. You can

use these parts separately for more loading

flexibility. To disassemble the parts, move

them horizontally in opposite directions and

pull them apart. To assemble the parts, put

them together and move horizontally to each

other.

Upper basket

The upper basket is for saucers, salad bowls,

cups, glasses, pots and lids. Arrange the

items to let water touch all surfaces.

Adjustable cup racks

For longer items, fold the cup racks up. You

can set the cup racks in a medium position.

Put or hang the glasses with the stems into

the slots in the cup racks.

Glass holder

For glasses with long stems and longer

glasses, fold the glass holder up (fig. 1).

If you do not use the glass holder, put it to

the right side (fig. 2).

10 electrolux

Put the glasses on the prongs.

Adjustment of the height of the upper

basket

If you put large plates in the lower basket, first

move the upper basket to the upper position.

Do these steps to move the upper basket to

the upper or lower position:

1. Pull the basket out until it stops.

2. Lift the upper basket and move it down

until it latches in the upper or lower posi-

tion.

Maximum dimensions for plates with

upper basket in upper position.

18

25

32

Maximum dimensions for plates with

upper basket in lower position

20

25

30

electrolux 11

Arrangement of large plates in lower

basket

Use of detergent

Only use detergents (powder, liquid or

tablet) that are applicable for dishwash-

ers.

Follow the data on the packaging:

• Dosage recommended by the manu-

facturer.

• Storage recommendations.

Do not use more than the correct quan-

tity of detergent to save an environment.

Do these steps to fill the detergent dispenser:

1. Open the lid of the detergent dispenser.

2. Fill the detergent dispenser (A) with de-

tergent. The marking shows the dosage:

20 = approximately 20 g of detergent

30 = approximately 30 g of detergent.

3. If you use a washing programme with

prewash phase, put more detergent in

the prewash detergent compartment (B).

A

B

4. If you use detergent tablets, put the de-

tergent tablet in the detergent dispenser

(A).

12 electrolux

5. Close the lid of the detergent dispenser.

Press the lid until it locks into position.

Use of detergent tablets

Put the detergent tablet in the detergent dis-

penser (A).

Detergent tablets contain:

• detergent

•rinse aid

• other cleaning agents.

Do these steps to use detergent tablets:

1. Make sure that the detergent tablets are

applicable for your water hardness. Refer

to the instructions from the manufacturer.

2. Set the lowest levels of water hardness

and rinse aid dosage.

It is not necessary to fill the salt container

and the rinse aid dispenser.

Do these steps when the drying results

are not satisfactory:

1. Fill the rinse aid dispenser with rinse aid.

2. Set the rinse aid dosage to position 2.

Do these steps to use the detergent

powder again:

1. Fill the salt container and the rinse aid

dispenser.

2. Set the water softener to the highest level.

3. Do a washing programme without

dishes.

4. Adjust the water softener. Refer to the

chapter 'Setting the water softener'.

5. Adjust the rinse aid dosage.

Different brands of detergent dissolve in

different times. Some detergent tablets

do not have the best cleaning results

during short washing programmes. Use

long washing programmes when you

use detergent tablets to fully remove the

detergent.

Multitab function

The multitab function is for combi detergent

tablets.

These tablets contain agents such as deter-

gent, rinse aid and dishwasher salt. Some

types of tablets can contain other agents.

Do a check if these tablets are applicable for

the local water hardness. Refer to the in-

structions from the manufacturer.

When you set the multitab function, it stays

on until you deactivate it.

The multitab function stops automatically the

flow of rinse aid and salt. The rinse aid indi-

cator light and salt indicator light are deacti-

vated.

The programme duration can increase if you

use the multitab function.

Activate or deactivate the multitab func-

tion before the start of a washing pro-

gramme.

You cannot activate or deactivate the

multitab function when the programme

operates. Cancel the washing pro-

gramme, then set the programme again.

To activate the multitab function:

• Press the multitab button. The multitab in-

dicator light comes on.

To deactivate the multitab function:

• Press the multitab button. The multitab in-

dicator light goes off.

Do these steps if the drying results

are not satisfactory:

1. Fill the rinse aid dispenser with rinse

aid.

2. Activate the rinse aid dispenser.

3. Set the rinse aid dosage to position

2.

• You can only activate or deactivate

the rinse aid dispenser when the mul-

titab function is activated.

To activate the rinse aid dispenser

1. Switch on the appliance.

electrolux 13

2. Make sure that the appliance is in setting

mode.

3. Press and hold function buttons B and C.

– The indicator lights for function buttons

A, B, and C start to flash.

4. Press function button B.

– The indicator lights for function buttons

A and C go off.

– The indicator light for function button B

continues to flash.

5. Press function button B again.

– The end-of-programme indicator light

comes on. The rinse aid dispenser is

active.

6. Switch off the appliance to save the op-

eration.

To deactivate the rinse aid dispenser do the

above steps until the end-of-programme in-

dicator light goes off.

To use normal detergent again:

1. Deactivate the multitab function.

2. Fill the salt container and rinse aid

dispenser.

3. Adjust the water hardness setting to

the highest level.

4. Do a washing programme without

dishes.

5. Adjust the water softener to the wa-

ter hardness in your area.

6. Adjust the rinse aid dosage.

Setting and starting a washing programme

Set the washing programme with the

door ajar. The washing programme only

starts after you close the door. Until then

it is possible to modify the settings.

Do these steps to set and start a washing

programme:

1. Switch on the appliance.

2. Make sure that the appliance is in setting

mode.

3. Select a washing programme. Refer to

the chapter 'Washing programmes'.

– The indicator light of the programme

comes on.

– The phase indicator lights for the pro-

gramme start to flash.

– The programme button indicator light

flashes.

4. Close the door. The washing programme

starts automatically.

– The phase indicator lights go off but not

the indicator light of the phase in oper-

ation.

– The programme button indicator light

is on with a static light.

When the washing programme oper-

ates, you cannot change the pro-

gramme. Cancel the washing pro-

gramme.

Warning! Only interrupt or cancel a

washing programme if necessary.

Caution! Open the door carefully. Hot

steam can come free.

Interrupting a washing programme

Open the door.

• The programme stops.

Close the door.

• The programme continues from the point

of interruption.

Cancelling a washing programme

1. Press and hold function buttons B and C.

– The set washing programme light goes

off.

– The phase indicator lights go off.

– The programme button indicator light

comes on.

– The end-of-programme indicator light

comes on.

2. Release function buttons B and C to can-

cel the washing programme.

At this time you can do these steps:

1. Switch off the appliance.

2. Set a new washing programme .

Fill the detergent dispenser with detergent

before you set a new washing programme.

End of the washing programme

Switch off the appliance in these conditions:

• The appliance stops automatically.

• The end-of-programme indicator light

comes on.

• The indicator light of the completed pro-

gramme stays on.

1. Press the on/off button.

2. Open the door.

3. For better drying results, keep the door

ajar for some minutes before you remove

the dishes.

14 electrolux

Let the dishes cool down before you remove

them from the appliance. Hot dishes are

easily damaged.

Removing the load

• First remove items from the lower basket,

then from the upper basket.

• There can be water on the sides and door

of the appliance. Stainless steel becomes

cool more quickly than the dishes.

Washing programmes

Programme Degree of soil Type of load Programme description Half-load op-

tion

Intensive Heavy soil Crockery, cut-

lery, pots and

pans

Prewash

Main wash up to 70°C

2 intermediate rinses

Final rinse

Drying

yes

ECO

1)

Normal soil Crockery and

cutlery

Prewash

Main wash up to 50°C

1 intermediate rinse

Final rinse

Drying

no

Quick Light soil Crockery and

glassware

Main wash up to 45°C

1 intermediate rinse

Final rinse

Drying

no

1) Test programme for test institutes. Please refer to separate leaflet supplied, for test data.

Consumption values

Programme Duration (in minutes) Energy (in kWh) Water (in litres)

Intensive 105 - 126 1,8 - 2,1 22 - 24

ECO 165 - 175 1,0 - 1,1 14 - 15

Quick 65 - 75 0,8 - 0,9 13 - 14

The pressure and temperature of the

water, the variations of power supply

and the quantity of dishes can change

these values.

Care and cleaning

Warning! Switch the appliance off

before you clean the filters.

Cleaning the filters

Caution! Do not use the appliance

without the filters. Make sure that the

installation of the filters is correct.

Incorrect installation will cause

unsatisfactory washing results and

damage to the appliance.

If necessary, clean the filters. Dirty filters de-

crease the washing results.

The dishwasher has two filters:

1. coarse filter (1)

2. fine filter (2)

electrolux 15

Make a check of the coarse filter after

each washing programme.

Make a check of the fine filter at regular

intervals.

Coarse filter (1)

1. Open the door.

2. Remove the lower basket.

3. Remove the coarse filter, clean it fully un-

der running water.

4. Put back in position the coarse filter.

Fine filter (2)

1. Open the door and remove the lower

basket.

2. Hold the fine filter by the handle.

3. To remove the fine filter, turn the handle

to the right.

4. Clean the fine filter fully with a brush under

running water.

5. Put the fine filter back in position.

6. To lock the fine filter system, turn the han-

dle to the left. Make sure that the signs on

the filter agree with each other.

Cleaning the spray arms

At regular intervals make sure that the

nozzles in the spray arms are not

blocked. If necessary, clean the nozzles

with a piece of wire or a needle under

running water.

Caution! To prevent damage to the

nozzle openings, clean them carefully.

Ceiling spray arm

1. Turn the fixing screw (A) counterclock-

wise.

2. Pull the spray arm off the shaft.

3. Clean the spray arm and the fixing screw.

4. Attach the spray arm with the fixing screw

by turn it clockwise.

16 electrolux

Upper basket spray arm

1. To remove the upper basket spray arm,

turn it laterally.

2. Clean the spray arm.

3. To attach again the spray arm, press up-

wards until it goes back into position.

Lower spray arm

1. Turn the fixing screw B) counterclock-

wise.

2. Pull the spray arm off the shaft.

3. Clean the spray arm and the fixing screw.

4. Attach the spray arm with the fixing screw

by turn it clockwise.

External cleaning

Clean the external surfaces of the appliance

and control panel with a damp soft cloth.

Only use neutral detergents. Do not use

abrasive products, scouring pads or solvents

(acetone, trichloroethylene etc...).

Frost precautions

Caution! Do not install the appliance

where the temperature is below 0 °C.

The manufacturer is not responsible for

damage because of frost.

If not possible, empty the appliance and

close the door. Disconnect the water inlet

hose and remove water from the water inlet

hose.

What to do if…

The appliance does not start or stops during

operation.

If there is a fault, first try to find a solution to

the problem yourself. If you cannot find a sol-

ution to the problem yourself, contact the

Service Force Centre.

Caution! Switch off the appliance

before you do the below suggested

corrective actions.

Fault code and malfunction Possible cause and solution

• continuous flash of the light of the

running programme

• 1 flash of the end-of-programme

indicator light

The dishwasher does not fill with wa-

ter

• The water tap is blocked or furred with limescale.

Clean the water tap.

• The water tap is closed.

Open the water tap.

• The filter in the water inlet hose is blocked.

Clean the filter.

• The connection of the water inlet hose is not correct. The

hose can be kinked or squashed.

Make sure that the connection is correct.

electrolux 17

Fault code and malfunction Possible cause and solution

• continuous flash of the light of the

running programme

• 2 flashes of the end-of-pro-

gramme indicator light

The dishwasher will not drain

• There is a blockage in the sink spigot.

Clean the sink spigot.

• The connection of the water drain hose is not correct. The

hose can be kinked or squashed.

Make sure that the connection is correct.

• continuous flash of the light of the

running programme

• 3 flashes of the end-of-pro-

gramme indicator light

The anti-flood device operates

• Close the water tap and contact your local Service Force

Centre.

The programme does not start • The appliance door is not closed.

Close the door.

• Mains plug is not connected in.

Put in the mains.

• The fuse has blown out in the household fuse box.

Replace the fuse.

After the check, switch on the appliance. The

programme continues from the point of in-

terruption. If the malfunction shows again,

contact your Service Force Centre.

These data are necessary to help you quickly

and correctly:

•Model (Mod.)

• Product number (PNC)

• Serial number (S.N.)

For these data, refer to the rating plate.

Write the necessary data here:

Model description : ..........

Product number : ..........

Serial number : ..........

The cleaning results are not satisfactory

The dishes are not clean • The selected washing programme is not applicable for the type of

load and soil.

• The baskets are loaded incorrectly so that water cannot reach all

surfaces.

• Spray arms do not turn freely because of incorrect arrangement of

the load.

• The filters are dirty or not correctly installed.

• The quantity of detergent is too little or missing.

Limescales particles on the

dishes

• The salt container is empty.

• The water softener is adjusted on a wrong level.

• The salt container cap is not closed correctly.

The dishes are wet and dull • No rinse aid has been used.

• The rinse aid dispenser is empty.

There are streaks, milky spots

or a bluish coating on glasses

and dishes

• Decrease the rinse aid dosage.

Dry water drop signs on

glasses and dishes

• Increase rinse aid dosage.

• The detergent can be the cause.

Technical data

Dimensions Width cm 54,6

Height cm 75,9

Depth cm 57,1

Electrical connection - Voltage -

Overall power - Fuse

Information on the electrical connection is given on the rating plate

on the inner edge of the dishwasher door.

18 electrolux

Water supply pressure Minimum 0,5 bar (0,05 MPa)

Maximum 8 bar (0,8 MPa)

Capacity Place settings 11

Installation

Warning! Make sure that mains plug is

disconnected from the mains socket

during installation.

Install the appliance under a counter (kitchen

worktop or sink).

If a repair is necessary, the appliance must

be easily accessible for the engineer.

Put the appliance adjacent to a water tap and

a drain.

For the venting of the dishwasher only water

fill, water drain and power supply cable open-

ings are necessary.

Make sure that the water inlet hose, the drain

hose and the supply cable are not kinked or

squashed, when you insert the machine.

Attaching the appliance to the adjacent

units

Make sure that the counter below which you

attach the appliance is attached to a safe

structure (adjacent kitchen units, cabinets,

wall).

1. Set the appliance in front of the kitchen

unit. Put the mains cable and the hoses

into the recess unit.

2. Push the appliance in and pull the mains

cable and the hoses through. Make sure

that they are not kinked or squashed.

3. Align the appliance and attach it on the

two sides in the upper area of the tub.

Other attaching possibilities

1. On the plinth.

105

50

2. Additional bracket on the top. This is

available as a special accessory. Contact

the Service Force Centre.

electrolux 19

Water connection

Water inlet hose

Connected the appliance to a hot (max. 60°)

or cold water supply.

If the hot water comes from alternative sour-

ces of energy that are more environmentally

friendly (e.g. solar or photovoltaic panels and

aeolian), use a hot water supply to decrease

energy consumption.

Connect the inlet hose to a water tap with an

external thread of 3/4”.

Caution! Do not use connection hoses

from an old appliance.

The water pressure must be in the limits (refer

to 'Technical data'). Make sure that the local

water authority gives you the average mains

pressure in your area.

Make sure that there are no kinks in the water

inlet hose and that the water inlet hose is not

squashed or entangled.

Fit the locknut correctly to prevent water

leaks.

We recommend that you install an IRG filter.

Caution! Do not connect the appliance

to new pipes or pipes that are not used

for a long time. Let the water run for

some minutes, then connect the inlet

hose.

The water inlet hose is double-walled and

has an inner mains cable and a safety valve.

The water inlet hose is under pressure only

while the water is running. If there is a leak in

the water inlet hose, the safety valve inter-

rupts the running water.

Be careful when you connect the water inlet

hose:

• Do not put the water inlet hose or the safe-

ty valve in water.

• If the water inlet hose or the safety valve is

damaged, immediately disconnect the

mains plug from the mains socket.

• Only let the Service Force Centre replace

the water inlet hose with safety valve.

Warning! Dangerous voltage

Water drain hose

Make sure that the drain hose is not bent or

squashed to prevent that the water drains

does not drain correctly.

Remove the sink plug when the appliance

drains the water to prevent that the water

goes back into the appliance.

The drain hose connection must be at a max-

imum height of 70 cm from the ground.

N 762+3105N 600

G 57020

G 759

70

100 180

550

G 546

N 550

50

400

max. 700

600

DD

WKE

A

CC

BB

A - drain outlet

E - socket

G - dimension of the appliance

K - cold water supply

N - dimension of the recess

W - hot water supply

If you connect the water drain hose to a trap

spigot under the sink, remove the plastic

membrane (A). If you do not remove the

membrane, remaining food can cause a

blockage in the drain hose spigot

20 electrolux

La page charge ...

Electrolux GA553IF Manuel utilisateur

Electrolux GA553IF Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents