TAIYO YUDEN EYSSSN Manuel utilisateur

Taper
Manuel utilisateur
15-Sep.2020 Ver.0.9
TAIYO YUDEN CO., LTD.
TAIYO YUDEN CO., LTD.
1/4
EYSSSN
User manual
(for EYSSSN)
FCC ID: RYYEYSSSN
IC Number: 4389B-EYSSSN
15-Sep.2020 Ver.0.9
TAIYO YUDEN CO., LTD.
TAIYO YUDEN CO., LTD.
2/4
EYSSSN
Since this module is not sold to general end users directly, there is no user manual of module.
For the details about this module, please refer to the specification sheet of module.
This module should be installed in the host device according to the interface specification
(installation procedure).
The following information must be indicated on the host device of this module;
1) Japan Regulatory Information
a) This Product is a radio system and obtained certification of construction type combined
with the specific antenna.
b) Please ensure that your product has a label with the following certification mark at easily
viewable location. If your product is too small to have the label, please place it in the
instruction manual and package of your product. The mark diameter shall be equal or
greater than 3mm. In case your product does not have the label with the following
certification mark, you or your customer who uses your product may be against the Radio
Law and subjected to criminal punishment. TAIYO YUDEN shall not be liable for any
loss or damage incurred by you or your customer arising from use of your product which
does not have following certification mark.
This product has a radio system which was approved as a radio station in a low
power data communication system based on the Radio Law.
EYSSSN : ***-******
2) Canada Regulatory Information
a) This device complies with Industry Canada’s applicable licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
1) l’appareil ne doit pas produire de brouillage;
2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
b) This product is certified as type of the portable device with Industry Canada Rules. To
maintain compliance with RF Exposure requirement,please use within specification of
this product.
Ce produit est certifié comme type de l'appareil portable avec Industrie Règles de
Canada. Pour maintenir l'acquiescement avec exigence Exposition de RF, veuillez
utiliser dans spécification de ce produit.
- IC: 4389B-EYSSSN
15-Sep.2020 Ver.0.9
TAIYO YUDEN CO., LTD.
TAIYO YUDEN CO., LTD.
3/4
EYSSSN
c) Please notify certified ID by either one of the following method on your product.
-Contains IC : 4389B-EYSSSN
Specifiez ID certifiée dans votre produit par une de méthode suivante.
-Contains IC : 4389B-EYSSSN
3) FCC Regulatory Information
a) This device complies with part 15 of the FCC Rules.
-Part 15 Subpart C
b) Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
c) Please notify certified ID by either one of the following method on your product.
-Contains Transmitter Module FCC ID: RYYEYSSSN
-Contains FCC ID: RYYEYSSSN
d) Since there is no space which indicates FCC ID on this module, FCC ID is indicated in
a manual. If the FCC ID is not visible when the module is installed inside another
device, then the module is installed must also display a label referring to the enclosed
module.
e) CAUTION: Changes or modifications not expressly approved by the party responsible
for compliance could void the use’s authority to operate the equipment.
f) The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC
transmitter rules) listed on the grant, and the host product manufacturer is responsible
for compliance to any other FCC rules that apply to the host not covered by the
modular transmitter grant of certification. The final host product still requires Part 15
Subpart B compliance testing with the modular transmitter installed.
g) This product is certified as type of the portable device with FCC Rules. To maintain
compliance with RF Exposure requirement, please use within specification of this
product.
h) The antenna used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
i) This module can change the output power depending on the circumstances by the
application software which is developed by module installer. Any end user cannot
change the output power. The test software is developed by TAIYO YUDEN, and
during regulatory testing the output power is set to maximum power.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
15-Sep.2020 Ver.0.9
TAIYO YUDEN CO., LTD.
TAIYO YUDEN CO., LTD.
4/4
EYSSSN
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
4) CE Regulatory Information
a) When your end product installs this module, it is required to proceed additional
certification processes before placing on the market in EU member states to make your
products fully comply with relative EU standards.
b) TAIYO YUDEN can provide you the test reports of conducted measurement portion for
the radio module. You can utilize the test reports for the certification processes of your
end product as it requires radio testing.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

TAIYO YUDEN EYSSSN Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues