21-Aug.2020 Ver.0.1

TAIYO YUDEN CO., LTD.

TAIYO YUDEN CO., LTD.

1/4

User manual

21-Aug.2020 Ver.0.1

TAIYO YUDEN CO., LTD.

TAIYO YUDEN CO., LTD.

2/4

Since this module is not sold to general end users directly, there is no user manual of module.

For the details about this module, please refer to the specification sheet of module.

This module should be installed in the host device according to the interface specification

(installation procedure).

The following information must be indicated on the host device of this module;

a) This device complies with Industry Canada’s applicable licence-exempt RSSs.

Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause

undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux

appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions

maintain compliance with RF Exposure requirement, please use within specification of

this product and have a separation distance of minimum 10 mm between the user

and/or bystander and the antenna and /or radiating element.

This distance ensures that the output power (e.i.r.p.) of EYSPBN is below the SAR

evaluation Exemption limits defined in RSS-102 issue 5.

Ce produit est certifié comme type de l'appareil portable avec Industrie Règles de

Canada. Pour maintenir l'acquiescement avec exigence Exposition de RF, veuillez

utiliser dans spécification de ce produit et respecter une distance de séparation d'au

moins 15 mm entre l'utilisateur et / ou un tiers et l'antenne et / ou l'élément rayonnant.

21-Aug.2020 Ver.0.1

TAIYO YUDEN CO., LTD.

TAIYO YUDEN CO., LTD.

3/4

c) Please notify certified ID by either one of the following method on your product.

-Contains IC : 4389B-EYSPBN

Specifiez ID certifiée dans votre produit par une de méthode suivante.

-Contains IC : 4389B-EYSPBN

a) This device complies with part 15 of the FCC Rules.

-Part 15 Subpart C

b) Operation is subject to the following two conditions: (1) This device may not cause

for compliance could void the use’s authority to operate the equipment.

e) The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC

transmitter rules) listed on the grant, and the host product manufacturer is responsible

for compliance to any other FCC rules that apply to the host not covered by the

modular transmitter grant of certification. The final host product still requires Part 15

Subpart B compliance testing with the modular transmitter installed.

f) This product is certified as type of the portable device with FCC Rules. To maintain

compliance with RF Exposure requirement, please use within specification of this

product.

g) The antenna used for this transmitter must not be co-located or operating in

NOTE:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation.If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

21-Aug.2020 Ver.0.1

TAIYO YUDEN CO., LTD.

TAIYO YUDEN CO., LTD.

4/4

a) When your end product installs this module, it is required to proceed additional

certification processes before placing on the market in EU member states to make your

products fully comply with relative EU standards.

b) TAIYO YUDEN can provide you the test reports of conducted measurement portion for

the radio module. You can utilize the test reports for the certification processes of your

end product as it requires radio testing.