HeatStar HS45GSP Le manuel du propriétaire

Marque: HeatStar

Modèle: HS45GSP

Catégorie: Chauffe-eau

Taper: Le manuel du propriétaire

READ INSTRUCTIONS CAREFULLY: YOUR SAFETY IS IMPORTANT TO YOU AND TO OTHERS.

Read and follow all instructions. Place instructions in a safe place for future reference. Do not allow

anyone who has not read these instructions to assemble, light, adjust or operate the heater.

OPERATING INSTRUCTIONS

AND OWNER’S MANUAL

MODEL#

45GSP

FOR YOUR SAFETY:

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WARNING: If the information in these instructions are not followed exactly, a fire or explosion may result

causing property damage, personal injury or loss of life.

ENERCO Group, Inc., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 866-447-2194

— WHAT TO DO IF YOU SMELL GAS

• Open Windows

• DO NOT try to light any appliance.

• DO NOT use electrical switches.

• DO NOT use any telephone in your house. Immediately call your local gas supplier from a telephone remote

from the area of the leak. Follow the gas supplier’s instructions.

• Do not touch any electrical switch; do not use any phone in your building.

• Installation and service must be performed by a qualified installer, service agency or the gas supplier.

• If you cannot reach your gas supplier, call the Fire Department.

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause

property damage, injury, or death. Read the installation, operating and maintenance instructions

thoroughly before installing or servicing this equipment.

LANGUAGES INCLUDED

•ENGLISH

•FRENCH

•SPANISH

Gas-Fired Low-Intensity Infrared Heater

Approved For Residential Garage/Commercial Applications

Installer: Leave this manual with the appliance. Consumer: Retain this manual for future reference.

2Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater

HAZARD WARNINGS

CONTACT INFORMATION

RETAIN THIS MANUAL FOR FUTURE REFERENCE.

FOR QUESTIONS, PROBLEMS, MISSING PARTS

BEFORE RETURNING TO RETAILER PLEASE CALL

WITH MODEL NUMBER AND SERIAL NUMBER OF

HEATER:

866-447-2194

CONTENTS

HAZARD WARNINGS ............................................... 2

INTRODUCTION ...................................................... 3

PLANNING ............................................................... 6

INSTALLATION ........................................................ 8

VENTING ................................................................. 11

OPERATION ............................................................ 17

MAINTENANCE ....................................................... 17

TROUBLESHOOTING .............................................. 18

ILLUSTRATED PARTS .............................................. 19

LIMITED WARRANTY ............................................. 20

WARNING:

YOUR SAFETY IS IMPORTANT TO YOU AND TO

OTHERS, SO PLEASE READ THESE INSTRUCTIONS

BEFORE YOU OPERATE THIS HEATER.

GENERAL HAZARD WARNING:

FAILURE TO COMPLY WITH THE PRECAUTIONS AND

INSTRUCTIONS PROVIDED WITH THIS HEATER CAN

RESULT IN DEATH, SERIOUS BODILY INJURY AND

PROPERTY LOSS OR DAMAGE FROM HAZARDS OF

FIRE, EXPLOSION, BURN, ASPHYXIATION, CARBON

MONOXIDE POISONING, AND/OR ELECTRICAL

SHOCK.

ONLY PERSONS WHO CAN UNDERSTAND AND

FOLLOW THE INSTRUCTIONS SHOULD USE OR

SERVICE THIS HEATER.

IF YOU NEED ASSISTANCE OR HEATER INFORMATION

SUCH AS AN INSTRUCTIONS MANUAL, LABELS, ETC.

CONTACT THE MANUFACTURER.

WARNING:

FIRE, BURN, INHALATION, AND EXPLOSION

HAZARD. KEEP SOLID COMBUSTIBLES, SUCH AS

BUILDING MATERIALS, PAPER, OR CARDBOARD,

A SAFE DISTANCE AWAY FROM THE HEATER.

AS RECOMMENDED BY THE INSTRUCTIONS

NEVER USE THE HEATER IN SPACES WHICH DO

OR MAY CONTAIN VOLATILE OR AIRBORNE

COMBUSTIBLES, OR PRODUCTS SUCH AS

GASOLINE, SOLVENTS, PAINT THINNER, DUST

PARTICLES OR UNKNOWN CHEMICALS.

WARNING:

THIS PRODUCT CAN EXPOSE YOU TO CHEMICALS

INCLUDING LEAD AND LEAD COMPOUNDS,

WHICH ARE KNOWN TO THE STATE OF

CALIFORNIA TO CAUSE CANCER AND BIRTH

DEFECTS OR OTHER REPRODUCTIVE HARM. FOR

MORE INFORMATION VISIT

WWW.P65WARNINGS.CA.GOV

MONDAY-FRIDAY 8-5 EASTERN TIME

OR E-MAIL USING THE HEATSTAR WEBSITE:

WWW.HEATSTARBYENERCO.COM

SOCIAL MEDIA

In order to provide the best service possible

Heatstar is now giving you more ways to get in

touch with us:

WEBSITE: Heatstar’s full line of product are now at:

WWW.HEATSTARBYENERCO.COM

FACEBOOK: Find us on Facebook

TWITTER: Find us on twitter

YouTube: There are now informational

videos on YouTube.

WARNING: Fuels used in liquefied propane

gas appliances, and the products of combustion of such

fuel, can expose you to chemicals including benzene,

which is known to the state of California to cause cancer

and cause birth defects or other reproductive harm, for

more information go to www.P65Warnings.ca.gov

Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater 3

BEFORE YOU BEGIN

Read this manual carefully before installing or

servicing this equipment. Improper installation,

servicing, or maintenance will cause death,

injury, or property damage. Check the minimum

required safe distances from combustibles given

on the outside of each burner box to make sure

that the product is suitable for your application.

The minimum required safe distances from

combustibles is also found on page 8 of this

manual. Installer must be a licensed contractor or

representative. After the installation is complete,

check product operation as provided in these

instructions.

INTRODUCTION

UNPACKING THE HEATER

Manpower Requirements

To prevent personal injury and damage to the

heater, two persons will be required to remove

the heater from the carton. Both ends of the

heater should be lifted from the carton at the

same time. The burner box should be lifted by

gripping the bottom of the box. The reflector

end of the heater should be lifted using the rear

moveable hanger.

Safety

Thin sheet metal parts, such as the reflector

portion of the heater and the various venting

components, have sharp edges. To prevent

injury, the use of work gloves is recommended.

The use of gloves will also prevent the transfer

of body oils from the hands to the surface of the

reflector.

About The Heater

The 45GSP is a factory-assembled, gas fired, low-

intensity heating system. The system has been

designed for easy installation and will provide

years of economical operation and trouble-free

service. Not only is infrared heat efficient, it also

provides the most comfortable conditions in open

areas, such as workshops.

Gas-Fired means it uses clean-burning Natural

or LP gas. Low-Intensity means that the radiant

surface of the hear exchanger tube does

not glow red. Instead, it operates at a lower

temperature (less than 1000°F) and radiates

energy at a lower intensity per square foot of

radiating surface. The lower temperature and

intensity levels are within a range that is most

effective in establishing and maintaining personal

comfort levels. An aluminum reflector directs the

radiant energy downward to the occupied area.

Radiant refers to the energy radiated by the

tube heater. Because the energy is in the form

of infrared rays, it does not directly heat the air.

Instead, the rays heat objects such as the floor,

cars, machines and people. The warm objects,

in turn, heat the air. These combined features

are the key to the exceptional comfort and fuel

efficiency provided by the tube heater.

Available Accessories

F102848 Category I Vertical Vent Kit

F102860 Category III Horizontal Stainless

Steel Vent Kit

F102859 Decorative Egg Crate Kit

F102834 Install Kit

10371 24V Thermostat

4Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater

Burner Box

Front Fixed Hanger

Reflector

Heat Exchanger

Rear Movable Hanger

Service Door

Burner Box Contains the electrical components (i.e. blower motor, power transformer, etc.)

and gas distribution components (i.e. gas valve, etc.) that make the heater work.

There are no owner serviceable items contained in this box.

Front Fixed

Hanger

Provides rigid support and mounting surface for the reflector. Holes are provided in

the upper corners and center of the bulk

Reflector The reflector is made from formed aluminum and reflects the radiant energy

downward to the space to be heated.

Heat Exchanger A U-shaped tube through which the heated products of combustion pass.

Rear Movable

Hanger

Provides support for the heat exchanger and reflector at the end that is furthest

from the burner box. The support may be moved (within limits) to accommodate

hanging of the unit.

Service Door To be removed only by a licensed contractor. Removal of this service door provides

access to the electrical and gas distribution components.

Intake Vent Accommodates a 3” diameter combustion air inlet duct that delivers fresh air to

the burner.

Exhaust Vent Accommodates the air-venting duct that carries the products of combustion to be

vented outdoors.

Nipple - ½” NPT Point at which the gas supply is connected to the heater.

Power Cord Includes a three prong plug that must be connected to a dedicated and properly

grounded three prong ceiling outlet.

Air Intake

Vent

Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater 5

Leading Particulars

Model No. BTU/hr Weight Length

GSP45 45,000 (13.2 kW) 91 lbs (41.3 kg) 10’ 3” (3.12 m)

HEATER SPECIFICATIONS

Electrical Voltage 120 V

Connection 3 pin molded plug

Gas Inlet

Connection ½Male NPT

Pressure for

Natural Gas

Minimum 5.0” W.C. (1.25 kPa)

Maximum 11.0” W.C. (2.74 kPa)

Pressure for LP

Gas (Propane)

Minimum 11.0” W.C.(2.74 kPa)

Maximum 13.0” W.C. (3.24 kPa)

Manifold Pressure Natural Gas 4.0” W.C. (1 kPa)

LP Gas (Propane) 10.0” W.C. (2.49 kPa)

VENTING SPECIFICATIONS

Air Intake/Venting

Pipe Requirements

Length Minimum 3’ (0.9144 m)

Length Maximum 25’ (7.62 m)

Intake Pipe Diameter 3.0” (7.62 cm)

Vent Pipe Diameter 4.0” (10.16 cm)

6Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater

Where can the heater be installed?

The GSP tube heater is intended for installation for light

industrial/commercial applications such as the following

areas:

• entrance ways

• lobby areas

• aircraft hangars (see page 7 for restrictions)

• public garages (see page 7 for restrictions)

• greenhouses

• workshops

Where can’t the heater be installed?

The GSP tube heater is not intended for installation

in the following areas:

• Residential living or sleeping areas

• Basements

Installer’s responsibility

The GSP tube heater, as well as the gas and electrical

supply, and the venting of the heater must be installed in

accordance with the applicable specifications and codes.

Only firms (or individuals) well qualified in this type of work

should install the system. Consult local Building Inspectors,

Fire Marshals for further guidance.

Use the information given in this manual together with

the cited codes and regulations to perform the installation.

The installer must furnish all needed materials that are not

furnished as standard equipment. It is also the installers

responsibility to see that the materials and installation

methods used result in a job that is workmanlike in

appearance and is in compliance with all applicable codes

and requirements to this manual. The installer must give

this manual to the owner.

The stated clearances to combustibles (page 8)

represents a surface temperature of 90°F (32°C) above

room temperature. Building material with low heat

tolerance (such as plastics, vinyl siding, canvas, tri-ply, etc.)

may be subject to degradation at lower temperatures.

It is the installer’s responsibility to assure that adjacent

materials are protected from degradation.

PLANNING

General

This section provides the following information:

• Defines the gas, electric and venting requirements for

the GSP tube heater.

• Specifies the national standards and applicable

codes that apply to the gas, electric and venting

requirements.

• Specifies the national standards and applicable codes

that apply to non-residential installations.

Gas Service Requirements:

Type of Gas

The type of gas appearing on the nameplate must be the

type of gas used. Installation must comply with local codes

and recommendations of the local gas company. United

States: Refer to National Fuel Gas Code, ANSI Z223.1 -

latest revision, (same as NFPA Bulletin 54). In Canada:

Refer to Can 1-B149.1: Installation Codes for Gas Burning

Appliances.

Gas Supply Lines

The size of the gas supply lines must comply with local

codes and recommendations of the local gas company.

United States: Refer to National Fuel Gas Code, ANSI

Z223.1 - latest revision, (same as NFPA Bulletin 54). In

Canada: Refer to CAN 1-B149.1: Installation Codes for

Gas Burning Appliances. A 1/8” NPT plugged tap must be

installed in the gas line connection immediately upstream

of the heater that is farthest from the gas supply meter.

The tap is required to check system gas pressure.

Meter and Service

Meter and service must be large enough to handle all the

heaters being installed plus any other connected load. The

gas line which feeds the system must be large enough to

supply the required gas with a maximum pressure drop of

½”W.C. (0.125 kPa) When gas piping is not included in the

layout drawing, the local gas supplier will usually help in

planning the gas piping.

Electrical Service Requirements:

System Requirements

The GSP tube heater requires a grounded three-prong

electrical outlet to be installed within 36 inches of the rear

surface of the heater’s burner box. It is recommended that

the outlet for the heater be ceiling-mounted and should be

on a dedicated circuit. DO NOT use an electrical extension

cord to operate the heater.

Heater Rating: 120VAC, 60Hz, Single Phase, 1 Amp

WARNING:

Electrical Shock Hazard

Plug heater into grounded three-prong ceiling

receptacle. Do not cut or remove the grounding prong

from this plug. Do not use with an extension cord.

Failure to follow these instructions will result in death

or electrical shock.

Grounding

The heater must be electrically grounded in accordance

with the following codes: United States: Refer to National

Electrical Code ANSI/NFPA-70 latest revision. Wiring must

conform to the most current National Electrical Code and

local ordinances. In Canada: Refer to Canadian Electrical

Code, CSA C22.1 Part 1 - latest revision.

Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater 7

Air Intake/Venting

Pipe Requirements

Length Minimum 3’ (0.9144 m)

Length Maximum 25’ (7.62 m)

Venting Codes

The location, size, installation and termination of vents,

as well as the minimum required safe distances when

penetrating combustible walls, must comply with local

codes and recommendations of the local gas company.

United States: Refer to National Fuel Gas Code, ANSI

Z223.1 - latest revision, (same as NFPA Bulletin 54). In

Canada: Refer to Can 1-B149.1: Installation Codes for Gas

Burning Appliance.

WARNING:

Carbon Monoxide Hazard

Heater must be exhausted outside.

Use materials supplied.

Failure to follow these instructions will result in death

or injury.

Non-residential Installations:

Aircraft Hangars

The GSP tube heater may be used in certain areas of

aircraft hangars. Installation in aircraft hangars must be in

accordance with the following codes: United States: Refer

to Standard for Aircraft Hangars, ANSI/NFPA-409 - latest

revision. Canada: Refer to Standard CGA B149-1M91.

Heaters in aircraft storage or service areas must be installed

a minimum of 10 feet (3.048 m) above the upper surface

of wings or engine enclosures of the highest aircraft which

may be housed in the hangar. (This should be measured

from the bottom of the heater to the top of the wing, or

engine enclosure, whichever is highest from the floor).

In other sections of aircraft hangars, such as shops or

office, heaters must be installed a minimum of 8 feet (2.44

m) above the floor.

Heaters installed in aircraft hangars shall be located so as

not to be subject to damage by aircraft, cranes, movable

scaffolding or other objects.

When installed over hoists, the minimum required safe

distances to combustibles must be maintained from the

uppermost point of the combustible materials placed on

the hoist.

Public Garages

The GSP tube heater may be used in public garages.

Installation in public garages must be in accordance with

the following codes: United States: Standard for Parking

Structures NFPA-88A-Latest revision, or the Standard

for Repair Garages, NFPA-88B-Latest revision. Canada:

Refer to Can 1-B149.1: Installation Codes for Gas Burning

Appliances.

Heaters must be installed a minimum of eight feet (2.43

meters) above the floor. Minimum required safe distances

to combustibles must be maintained from vehicles parked

below the heater.

When installed over hoists, the minimum required safe

distances to combustible must be maintained from the

uppermost point of the combustible materials placed on

the hoist.

Hazardous Locations

Where there is the possibility of exposure to combustible

airborne material or vapor, consult the local Fire Marshal,

the Fire Insurance Carrier or other authorities for approval

of the proposed installation.

Venting Requirements:

System Requirements

The GSP tube heater must be installed with venting or with

one of the optional venting kits available from Enerco.

DO NOT connect this heater to a separate chimney. Gas

appliances must not be connected to a chimney flue

serving a separate solid-fuel burning appliance. DO NOT

common vent with any other fuel burning appliance.

8Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater

INSTALLATION

Safety Equipment

Use of the following safety equipment is recommended for

installation of the GSP tube heater:

• Work gloves

• Safety glasses

Installation Tools

Tools required for the installation of the GSP tube heater

may include the following:

• Tape measure

• Electrical drill (with an assortment of drill bits)

• Pipe wrenches - 2 required

• Screwdriver

• Staple gun

• Level

• Pliers

Installation Materials

Materials required for the installation of the GSP tube

heater include the following:

• High temperature silicone sealant

• Suspension hooks (capable of supporting 150 pounds

[68 kg] each)

• Sheet metal screws

The following items may be required for your particular

installation:

• Plastic drain hose

• Additional vent pipe

• Roof flashing

• Rain collar

• Chain - 2/0, or equivalent

• S-hooks (as required)

WARNING:

Several steps are involved in the installation of the

heater. DO NOT attempt to operate the heater

until ALL steps of the installation have been

accomplished. Failure to follow this warning will

cause death, injury or property damage.

Choose Location for Heater

When selecting a suitable mounting location for the GSP

tube heater it is important to consider the following:

1. The heater must meet the minimum mounting height

requirement of 7 feet (2.13 m) above the floor. For

aircraft hangars and public garages, the heater must

meet the minimum mounting height requirement of 8

feet (2.43 m) above the floor.

2. The proposed mounting location allows for the

minimum required safe distances from combustibles

(combustibles include vehicles, wood, gasoline and

flammable objects, liquids, and vapors).

3. The proposed mounting location of the heater will not

restrict motion of passageway doors or windows.

4. The proposed mounting location of the heater will not

interfere with operation of the overhead garage door.

5. The proposed location will provide the best coverage

of the total area to be heated.

6. The proposed location must provide for adequate

combustion and ventilation air.

7. The proposed location must provide for adequate

accessibility clearance for service and proper operation.

8. Consideration be given to the types of vehicles that will

be parked in the garage (cars, vans, boats, RV’s etc.).

9. The proposed location will allow for the minimum

required safe distances from combustibles with respect

to the vehicles parked in the garage.

10. The proposed location will allow the required utilities

(i.e.: gas and electric) and venting to be installed

(maximum vent length is 25 feet [7.62 m]).

11. Sufficient clearances will exist to allow for

maintenance.

12. Overhead structural members (rafters, beams, etc.) are

accessible for attaching the heater.

13. Location must allow for adequate clearance around air

openings into the combustion chamber.

In all situations, the minimum required safe distances

from combustibles must be maintained. Combustibles

are materials which may catch on fire and include many

common items such as wood, paper, rubber, fabrics, etc.

Combustible materials such as those noted, and any other

combustible materials must not be placed closer to any

base or side of the GSP tube heater than the distances

noted in the diagrams on the following page. If you have

any questions about the minimum required safe distances

from combustibles, or the associated diagrams, please

contact your installer, Enerco representative or distributor,

of Enerco Technical Products during normal business hours

which are Monday through Friday, 8:15 a.m. to 4:45 p.m.,

Eastern Time.

Telephone: 866-466-2194

It is important to keep the minimum required safe

distances from combustibles at all times to avoid death,

personal injury or property damage. Clearances from

vehicles parked beneath heaters must be maintained.

Signs should be posted to identify any possible violation

of the clearance distances from the heater in the vehicle

areas. Maximum allowable stacking height in storage areas

should be identified with signs or appropriate markings.

The illustrations and tables on the adjoining page specify

the minimum required safe distances from combustibles.

Minimum Required Safe Distances from Combustibles

Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater 9

Horizontal Installations

45 ° Tilted Installations

Note: Dimension “B” indicates the minimum required safe distances from combustibles, it DOES NOT

indicate the required mounting height. The minimum mounting height is 7 feet, except for aircraft

hangars and public garages.

A B C D E F

6”

(15.24 cm )

54”

(137.16 cm)

24”

(60.96 cm)

24”

(60.96 cm)

24”

(60.96 cm)

6”

(15.24 cm )

A B C D E F

6”

(15.24 cm )

36”

(91.44 cm)

36”

(91.44 cm)

6”

(15.24 cm )

24”

(60.96 cm)

6”

(15.24 cm )

10 Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater

Hang the Heater

Installation locations come in a variety of sizes, shapes,

styles and methods of construction. Because of all these

variables, it is not possible to include mounting hardware

with the GSP heater. Although wooden rafters and joists

are the most common overhead structural members

in residential garage applications, other structural

configurations are also illustrated below.

In the typical suspension methods shown below, lengths

of chain are shown as a means of lowering the heater.

However, for most installation applications it may not be

necessary to lower the heater. Instead, it may be possible

to screw hook-type hardware into the underside of a beam.

The exposed hook could directly engage one of the three

mounting holes in the front fixed hanger, while another

hook could engage in one of the three suspension loops of

the rear movable hanger.

Whichever method of suspension is selected, the two

required suspension points must be capable of supporting

a minimum of 150 pounds (68 kg) each.

Heater Orientation

The GSP tube heater may be installed in any of the three

orientations indicated below. Select the heater orientation

that is best suited for the location that you have chosen for

your heater.

• Horizontally

• Tilted 45° Right

• Tilted 45° Left

Wood Beam

As Required

S-Hook

Anchor

Wood Beam

Washer

Locknut

Washer

Screw Hook

min. 3/8” (10mm)

Most common

installation applications

Threaded Hook

Concrete Beam

Bar Joist Clip

Truss

Beam Clamp

I-Beam

Most common for non-residential applications

NOTE: If the heater is going to be vented through the

roof, be sure to carefully review the roof option

installation portion of this section. Ensure that the

selected mounting site will satisfy the measurement

parameters (vent length not to exceed 25 feet

[7.62 m]) described in that section.

Horizontal Installation

1. Using S-hooks, attach two equal lengths of 2/0 chain,

or equivalent, to the two uppermost holes in the front

fixed hanger.

2. Slip the free end of both chains onto another S-hook,

as shown.

3. The uppermost S-hook can now be installed on the

suspension hardware that you have installed for

suspension of the unit. An additional length of chain

may also now be installed, if required, to lower the

heater.

NOTE: The hook portion of hook-type suspension

hardware may directly engage the two holes in the front

fixed hanger and the center loop of the rear moveable

hanger.

Front Fixed Hanger

Rear Movable

Hanger

45 ° Tilted Installations

1. Determine if the heater is going to be tilted left, or

tilted right. The front and rear suspension points

selected must be on the same side (left or right) of the

heater as shown below.

2. Attach suspension hooks and/or chains to the selected

suspension points of the heater.

Tilted Left

Use these two suspension points for Tilted

45° Left Installation

Tilted Right

Use these two suspension points for Tilted

45° Right Installation

Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater 11

Typical Installation

The Illustration below shows a typical installation of the

GSP tube heater. The installation drawing shown has a

straight horizontal venting arrangement and specifies the

minimum space required for maintenance, as well as the

allowable range of distances between the two suspension

points.

Detailed venting arrangements are illustrated in following

portions of this section.

X Dimension

Min. Max.

72”

(1.82 m)

95”

(2.44 m)

Air Intake

Exterior

Wall

Outside wall thickness

10” max. ½” min.

(25.4 cm max) (1.27 cm min)

Burner Box Reflector

6” Min

(15.24 cm)

Suspension

Points

1” Max

(2.54 cm)

15 ”

(38.1 cm)

24”

(60.96 cm)

Minimum

Recommended

for servicing X

Minimum Mounting

Height 7 feet*

(2.13 m)

(*) For minimum mounting height in aircraft hangars and public garages.

VENTING

• Venting must be in compliance with the latest edition

of the National Fuel Gas Code (ANSI Z223.1 latest

edition: or the authority having jurisdiction.)

• Uninsulated single-wall metal pipe shall not be used

outdoors in cold climates for venting of these heaters

as specified by Section 7.8 of the ANSI Z223.1NFPA 54

National Fuel Gas Code-latest edition.

• For the installation of a single-wall metal pipe through

an exterior combustible wall, refer to the latest edition

of the National Fuel Gas Code or the authority having

jurisdiction.

• In regions of the country where prevailing winds are

consistently higher than 40 mph (64.4 kmh), it may be

necessary to terminate the vent system above the roof

level.

Other venting references can be found in equipment

volume of the ASHRAE Handbook.

General Guidelines

Regardless of the venting arrangement that will be

connected to the heater, the following general guidelines

for venting must be followed:

1. The installation must conform with local codes or in

the absence of local codes with the National Fuel Gas

Codes, ANSI Z223.1/NFPA 54, Natural Gas and Propane

Installation Code, CSA B149.1 for Canada.

2. Appliance input ratings are based on sea level operation

need not be changed for operating up to 2,000 feet

(609.9m) elevation. For operation at elevations above

2,000 feet (609.9m) contact manufacturer for specified

deration condition for Canada and the United States.

A. VERTICAL VENTING THROUGH THE ROOF

This heater, when vertically vented, must be installed with

the approved venting system. For vertical vent installations

the GSP45 tube heater is certified as a category I appliance.

NOTE: For applications where the heater must not be

connected to a separate chimney, it must be

installed using the venting system as specified

below.

1. When venting the heater to outside of building through

a roof, use 4 inch (10.16 cm) O.D. single-wall metal

pipe. This is to be constructed of galvanized sheet metal

or other approved noncombustible, corrosion-resistant

material as indicated by state and/or local codes.

2. A vent passing through a combustible roof shall extend

through a 2-inch (5.08 cm) clearance roof thimble.

Double-wall, Type B vent must be used for the portion

of the vent system which passes through the roof. An

approved vent cap (such as Leslie “VeraCap” Type B)

must be attached to the end of the flue.

3. The appliance and its main gas valve must be

disconnected from the gas supply piping system during

any pressure testing of that system at test pressures in

excess of ½psi (3.5kPa).

The appliance must be isolated from the gas piping

system by closing equipment shutoff valve during

pressure testing of the gas supply piping system at test

pressures equal to or less than ½psi (3.5kPa).

(WARNING) Materials and items, when stored under

this heater, will be subjected to radiant heat and could

be seriously damaged.

4. All horizontal venting sections must slope away from

the heater at a rate of ¼” per foot (0.635 cm per 0.3m)

5. The total length of vent pipe (horizontal and vertical

runs combined, plus the length of the exterior

termination) must not exceed 25 feet (7.62 m), and

must not be less than 3 feet (0.9144 m).

6. The vent terminal, mounted outside of the building,

should not be located above walkways. Condensate

produced during operation of the heater could drip

onto the walkway and could form ice during cold

weather.

7. Be sure that the venting installation is in accordance

with all applicable local codes and recommendations of

the local gas company.

8. DO NO connect this heater to a separate chimney, and

DO NOT common vent with any other fuel burning

appliance. Gas appliances must not be connected to

a chimney flue serving a separate solid-fuel burning

appliance.

9. Maintain a minimum of 1-inch (2.54 cm) clearance from

combustibles around all vent pipes.

10. Seal all vent pipe connections with high temperature

silicone sealant and secure each connection with three

sheet metal screws.

12 Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater

B. VENT TERMINATION

1. The vent terminal shall terminate above the roof

line so that no discharge opening is less than 2 feet

(0.6m) horizontally from the roof surface. The lowest

discharge opening will be no closer than the minimum

height specified in the following table. These minimum

heights may be used provided the vent is not less

than 8 feet (2.4m) from any vertical wall or similar

obstruction.

Not less then 8ft (2.44 M)

2ft (0.61M) min

vertical wall

H (Min.)

MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE

OPENING

Roof Pitch H Minimum

Flat to 6/12 (22.62°) 1.0 Feet (0.3m)

Over 6/12 (22.62°) to 8/12 (33.68°) 1.5 Feet (0.46m)

Over 8/12 (33.68°) to 10/12 (39.81°) 2.5 Feet (0.76m)

Over 10/12 (39.81°) to 12/12 (45°) 4.0 Feet (1.22m)

Over 12/12 (45°) to 16/12 (53.13°) 6.0 Feet (1.83m)

Over 16/12 (53.13°) to 20/12 (59.03°) 7.5 Feet (2.29m)

2. All other gas vents shall terminate not less than 2

feet (0.6m) above the highest point where they pass

through the roof and at least 2 feet (0.6m) higher than

any portion of a building located within 10 feet (3.1m)

as shown in the following illustration.

10 feet (3 m) or less

2 feet (0.61m) minimum

Vent Cap

Type B

Vent Pipe

Type B

(Double Wall)

Storm Collar

Boot Flashing

Vent Pipe

(Single Wall)

2” (5.1 cm)Clearance

Seal joint &

annular space

C. HORIZONTAL THROUGH THE SIDEWALL

This heater, when horizontally vented, must be installed

with the approved venting system. For horizontal vent

installations the GSP45 tube heater is certified as a

category III appliance.

1. When venting the heater to the outside of the building

through a sidewall, use 4 inch (10.16 cm) O.D. single-

wall metal pipe. This is to be constructed of stainless

steel.

3. The maximum equivalent length of vent pipe should

be carefully observed. A safety switch in the heater is

designed to shut the heater off before excessive flue

restriction causes bad combustion. In addition to the

length restrictions stated below, use no more than two

elbows in your vent system.`

Minimum Equivalent Length = 3 feet (0.9144 m) of Pipe

Maximum Equivalent Length = 25 feet (7.62 m) of Pipe

4. Joints between sections of piping shall be fastened

by sheet metal screws or other approved means. The

seams along the length of the piping and the joints

between sections of piping should be sealed to prevent

a potential leakage of flue gas into building. Use 100%

RTV Silicone Rubber Adhesive sealant suitable for 500°F.

(260°C)

5. All portions of the vent pipe shall be supported to

prevent from sagging.

6. When the vent pipe passes through areas where the

ambient temperature is likely to induce condensation of

the flue gasses, the vent pipe should be insulated and a

condensation drain should be provided.

7. The minimum clearance to combustible materials for

single-wall flue pipe shall be 6 inches (15.24 cm). This

may be reduced when the combustible material is

protected as specified in the National Fuel Gas Code or

the authority having jurisdiction.

8. Single-wall metal pipe shall not originate in any

unoccupied attic or concealed space and shall not pass

through any attic, inside wall or concealed space, or

through any floor.

9. A venting system shall terminate at least 3 feet (0.9m)

above any forced air inlet located within 10 feet (3.1m).

Vent Cap (Leslie VersaCap) Type B

2’ Min

(.61 m Min)

10’

(3m)

less

2’ Min (when no wall or parapet exist)

(.61 m Min when no wall or parapet exist)

Flashing

2” (5.1 cm)

Clearance Thimble

Seal joint &

annular space

VERTICAL

THROUGH THE ROOF

4”

(10.16 cm)

Vent Dia.

Total Vent

Height

(3’ Min.)

(0.91 m Min)

Lateral

SINGLE HEATER VENTING

Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater 13

NOTE: To minimize problems associated with

condensation in long runs, vent pipe can be

insulated.

3. The horizontal venting system approved with this heater

is the Horizontal Stainless Steel Vent Kit mentioned on

page 3 .

4. Limit the quantity of 90° elbows to two. When vent

pipe is in a horizontal run, it must be pitched upward

¼“ per foot (0.635 cm per 0.3m) towards the vent

terminal. The heater must be installed level.

5. The horizontal venting system shall not terminate:

Venting/Ducting

For Commercial and Industrial Installations Only

General Requirements

Use aluminum or teflon tape suitable for 550°F (3M

Company tapes #433 or #363) or RTV silicone sealant.

Heater must be vented in accordance with specification

ANSI Z223.1 - latest revision. Partial information relating

to this specification is provided in this section with regard

to size and configurations for venting arrangements. For

complete information consult ANSI Z223.1 - latest revision

and applicable local codes. Use the following guidelines to

help insure an adequate, safe venting arrangement.

a) Be sure that method selected for venting heater

complied with all codes are required for each particular

location.

b) Exhaust end of heater will accept a four (4”) inch

[10.16 cm] flue pipe using the flue pipe adapter.

c) Heater may be vented to the outdoors either vertically

or horizontally, provided that it follow category

guidelines.

d) If the heater is to be vented horizontally:

1. Vent must exit buidling not less than seven (7’) [2.13

m] feet above grade when located adjacent to public

walkways.

2. Vent must terminate at least one (1’) foot [0.3m]

above any forced air inlet located within ten feet

(10’) [3 m].

3. Vent must terminate at least four (4’) feet [1.22 m]

below, four (4’) feet [1.22 m] horizontally from, or

one (1’) foot [0.3m] above any door, window, or

gravity inlet into any building.

4. Vent terminal shall be located at least twelve (12”)

inches [0.3m] from any opening through which vent

gases could enter the building.

e) Vent terminal opening must be beyond any

combustible overhang.

f) If condensation in the flue is a problem, the flue length

should be shortened or insulated.

g) For vent specifications all of the following conditions

must be met:

The maximum equivalent length of vent pipe should

be carefully observed. A safety switch in the heater is

designed to shut the heater off before excessive flue

restriction causes bad combustion.

Minimum Equivalent Length = 3 feet (0.9144 m) of Pipe

Maximum Equivalent Length = 25 feet (7.62 m) of Pipe

Limit the quantity of 90° elbows to two. When vent

pipe is in a horizontal run, it must rise not less than ¼

inch per foot from the start of the vent system towards

the vent terminal.

2. For horizontal venting, the vent lengths may be as

follows:

Minimum Equivalent Length = 3 feet (0.9144 m) of Pipe

Maximum Equivalent Length = 25 feet (7.62 m) of Pipe

Vent Cap

24”

(0.61 m)

Wall Wall Thimble

CAT III

Vent Pipe

a) Less than 4 feet (1.2m) below, 4 feet (1.2m)

horizontally from, or 1 foot (30cm) above any

door, window or gravity air inlet into any building.

The bottom of the vent terminal shall be located

at least 7 feet (2.1m) above grade or above snow

accumulation levels as determined by local codes.

b) Less than 1 foot (0.3m) from a combustion air inlet.

c) Less than 3 feet (0.9m) from any other building

opening or any gas service regulator.

d) Directly over areas where condensate or vapor could

create a nuisance or hazard or be harmful to the

operation of gas utility meters, regulators, relief

valves, or other equipment. Building materials should

be protected from flue gases and condensate.

6. In regions of the country where prevailing winds are

consistently higher than 40 mph (64.4 kmh), it may be

necessary to terminate the vent system above the roof

level.

14 Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater

Alternative Arrangements / Optional Equipment for

Venting

Horizontal Venting

This heater, when horizontally vented, must be installed

with the approved venting system. For horizontal vent

installations the GSP45 tube heater is certified as a

category III appliance.

a) In combustible or noncombustible walls, use vent kits

on page 3. Follow vent manufacturer’s instructions

for proper installation.

b) Four (4”) inch [10.16 cm] O.D. flue pipe is required.

Twenty five (25’) feet [7.62 m] maximum length is

recommended.

c) All flue joints should be sealed using suitable product

such as General Electric RTV 106 or Permatex Form-

A-Gasket Red High Temperature Silicone Adhesive

Sealant.

d) Vent terminal should be installed at a height

sufficient to prevent blockage by snow.

e) Building materials should be protected from

degradation by flue gases.

Wall

2” (5.08 cm) clearance

thimble required when

flue pipe extends through

combustible materials

2” (5.08 cm)

clearance thimble

Roof or Building Overhang

24” Min.

(0.61 m)

3’-0” Min.

(0.91 m to 0 m Min)

6’-0” Min

(1.82 m to 0 m Min)

Parapet or Adjoining Building

Pitch flue pipe down

toward outlet ¼ per foot

for condensate drainage.

Note position of vent cap

openings.

Single Wall

Single wall vent run

Single wall terminal end

Vertical Venting

This heater, when vertically vented, must be installed with

the approved venting system. For vertical vent installations

the GSP45 tube heater is certified as a category I appliance.

a) Four (4”) inch [(10.16 cm) ] O.D. flue pipe, maximum

twenty five (25’) [7.62 M] feet in length may be

used as shown with approved vent cap.

b) An insulated thimble may be required to pass

through combustible structures (check local codes)

Type “B” Vent

(required outdoors)

Vent Cap

24 Inches

(0.61 m)

Roof Flashing

Approved Thimble

(if Applicable)

Single Wall Pipe

Secure all joints with 3 (minimum) #8 x 3/8”

sheet metal screws and seal all joints

Heater

Heater Exhaust Vent

Air For Combustion

If indoor combustion air is to be supplied for a tightly

enclosed area, one square inch of free area opening shall

be provided below the heater for each 1,000 BTU/hr of

heater input (6.45 square cm per 0.293 kW).

When outside air is used, the opening below the heater

shall be one square inch of free area for each 4,000 BTU/

hr of heater input (6.45 square cm per 1.172kW). In

contaminated atmospheres or high humidity areas, optional

outside air for combustion is recommended.

Adequate clearances around the perforated fresh air plate

must be maintained at all times. In larger open areas of

buildings, infiltration normally is adequate to provide air for

combustion.

Direct Outside Air For Combustion

Outside combustion air should be supplied directly to the

heater when the building is subject to negative pressure

or contaminants are present in the building air. These

contaminates include paints, solvents, corrosive vapors or

any other foreign particles that may cause damage to the

heater or result in poor combustion.

Outside combustion air can be brought directly to the

heater by a 3 inch (7.62 cm) diameter duct less than 25

feet (7.62 m) long or equivalent. This is attached to a 3

inch (7.62 cm) starting collar that is fitted on inlet side of

the control cabinet. An approved vent cap must be placed

directly to the end of the outside combustion air inlet

pipe. The combustion air inlet should be a minimum of 1

foot (0.3 m), either vertically or horizontally from the flue

vent termination. The air intake terminal must be located

not less than one foot (0.3 m) above grade. It is good

installation practice to supply combustion air from the

same pressure zone as the vent outlet.

In colder climates, where necessary, insult the fresh air

duct. Avoid location the fresh air duct directly above the

control box. Provide a capped clean out T as necessary.

The GSP tube heater is approved for installation with

an outside air supply system. Some compounds such as

halogenated hydrocarbons or other corrosive chemicals

c) All flue joints should be sealed using suitable products

(see recommendation for horizontal venting).

Clearance to be as

specified on type “B”

vent pipe.

Roof or Building Overhang

Wall

Pitch flue pipe down toward

outlet ¼” per foot

[0.635 cm per 0.3m]

for condensate drainage.

Note position of vent cap

openings.

Parapet or Adjoining Building

24” Min.

(0.61 m)

8” to 10” Max

(20.32 cm to 25.4 cm Max)

Double Wall

Double wall vent run

Double wall terminal end

3’-0” Min.

(0.91 m to 0 m Min)

6’-0” Min

(1.82 m to 0 m Min)

Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater 15

in the air can be drawn into the equipment and cause

an accelerated rate of corrosion of some of the heater

components. The use of such chemical compounds near

the enclosure should be avoided.

IMPORTANT: If the building has a slight negative

pressure or contaminants are present in the air, an

outside combustion air supply to the heater is strong

recommended.

For an outside air supply a three (3”) inch (7.62 cm) O.D.

single wall pipe may be attached to the heater. The duct

may be up to twenty five (25’) feet (7.62 m) maximum

length or three (3’) feet (0.91 m) minimum length with no

more than two (2) elbows.

The air supply duct may have to be insulated to prevent

condensation on the outer surface. The outside air terminal

should be securely fastened to the outside wall by drilling

four (4) holes in the outside flange; wood screws or bolts

and expansion sleeves may be used to fasten terminal.

Wall

Outside Air

Terminal

3” (7.62 cm)

Flue Pipe

Seal All Joints

Outside Air

Terminal

Horizontal Outside

Air

Vertical Outside Air

NOTE:

Flue pipe requires

additional support. Flex

pipe will not support riser

and outside air terminal.

Roof

Flex Pipe

6” to 12” long

(15.24 cm to 0.3 m)

Flex Pipe

6” to 12” long

(15.24 cm to 0.3 m)

Electrical Service Installation:

System Requirements

The GSP tube heater requires a grounded three-prong

electrical outlet to be installed within 36” (0.91 m) of the

rear surface of the heater’s burner box. It is recommended

that the outlet for the heater be ceiling-mounted and

should be on a dedicated circuit. DO NOT use an electrical

extension cord to operate the heater.

In order to control the heater thermostatically, it is

necessary the grounded three-prong electrical outlet

be controlled with a on/off switch or a line voltage

thermostat. Please consult with an electrician or follow all

local electrical codes.

Heater Rating: 120VAC, 60Hz, Single Phase, 1 Amp

Low Voltage Thermostat Wiring Diagram

Heaters are normally controlled by thermostat. The

recommended 24V thermostat connects to the unit as

shown in the diagram below.

Heater

Low Voltage

Thermostat

Stock # 10367

120V-60Hz

Supply Circuit

Heater (maximum 1-per thermostat)

WARNING Electrical Shock Hazard:

Plug heater into grounded three prong ceiling

receptacle. Do not cut or remove the grounding

prong from this plug. Do not use with an extension

cord. Failure to follow these instructions will result in

death or electrical shock.

CAUTION: Label all wires prior to disconnection when

servicing controls. Wiring errors can cause improper

and dangerous operation. Verify proper operation

after servicing.

Grounding

The heater must be electrically grounded in accordance

with the following codes: United Stats: Refer to National

Electrical Code, ANSI/NFPA-70-latest revision. Wiring must

conform to the most current National Electrical Code and

local ordinances. Canada: Refer to Canadian Electrical

Code, CSA C22.1 Part 1-latest revision.

The appliance, when installed, must be electrically

grounded in accordance with local code, or in the absence

of local codes, with the National Electrical Code (ANSI/

NFPA 70) or Canadian Electrical Code (CSA 22.1), if an

external electrical source is utilized.

Electrical Grounding Instructions

This heater is equipped with a three-prong

(grounded) plug for your protection against shock

hazard and should be plugged directly into a

properly grounded three-prong receptacle. Do not

cut or remove the grounding prong from this plug.

L’Instruction Mettre A Eletrique

Cet appareil de chaffage est equipe ave une trios

(mettre a terre) le bouchon pour votre protedtion

contre le danger da choc et devrait etre directement

plugged dans un convenablement a mis a terre

receptacle de trios broche. N’ pas couper ou enlever

la broche metrre a terre de ce bouchon.

Vent Cap

(Leslie VersaCap)

4” (10.16 cm) Dia.

Single-Wall Pipe

6” Min.

(15.24 cm)

Intake

Vent

3” (7.62 cm)

Starting Collar

Flashing

3’ (0.91 m)

Min.

VERTICAL THROUGH THE ROOF

3” (7.62 cm)

Flue Pipe

Seal All Joints

16 Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater

WIRING DIAGRAM

Gas Service Installation

Install Gas Supply Lines

A ½” (1.27 cm) gas supply connection is required as shown

below. To check system pressure, a plugged 1/8” NPT

tapping is required upstream of the manual gas shut-off

valve supplied with the heater.

Before connecting the heater to the supply system, verify

that all high pressure testing of the gas piping has been

completed.

DO NOT HIGH PRESSURE TEST THE GAS PIPING WITH THE

BURNER CONNECTED.

Follow these instructions to ensure a safe gas supply

system installation:

1. Support all gas piping with suitable pipe hanging

materials.

2. Use wrought iron or wrought steel pipe and malleable

iron fittings. The use of copper tube and brass fittings

is acceptable when such use is in compliance with local

codes. All pipe, tube, and fittings should be new and free

from defects. Carefully ream the pipe and tube ends to

remove obstructions and burrs.

3. Use LP-resistant joint compound on all threads.

4. Check the pipe and tube connections for leaks before

placing heating equipment into service. When checking

for gas leaks, use a soap and water solution; never use

an open flame.

5. The connector must be certified for use on a radiant

heater per “Standard for Connectors for Gas Appliances,

ANSI Z21.24 /CSA 6.10”

NOTE: A plugged 1/8” NPT tapping must be provided

upstream of the gas supply to the heater. The gas

supply line connecting to the heater appliance

should be such that it allows for some movement

of the unit. The appliance will go through

expansion and contraction during a heating cycle.

CORRECT POSITIONS

INCORRECT POSITIONS

WRONG

HEATER MOVEMENT

HEATER MOVEMENT HEATER MOVEMENT

END VIEW

ALTERNATE

POSITIONS

O K AY

VERTICAL

(AS SHOWN AT LEFT)

12”

(30 cm)

3” (7.62 cm) MAX

DISPLACEMENT

GND

24 VAC

IND

PSW

IGN

FC-

FC+

LED

Earth Ground

CONTROL BOARD

Chassis Wiring Is 18 AWG / 105 Degrees C / @ 600 Volts

Igniter Wire Is 16 AWG / 25 KVDC / 10 KVDC

Crimp Caps Are # CE5 / 105 Degrees C

SECONDARY - 24V

PRIMARY - 120V

PCB

IND

PCB

IGN

IGNITER/FLAME SENSOR

BURNER

PCB

PSW

PCB

T'STAT (Optional)

JUMPER (Optional)

24 VAC

PCB

PRESSURE SWITCH

PCBPCB

V1 V2

GND

Earth &

Chassis Ground

Replace Any Wiring With Same Ratings

All Quick Connects Are Fully Insulated (Except Igniter)

Line

Load

Blower Motor Cavity

Thermostat

Pressure Switch

Igniter & Flame Sense

BLACK

WHITE

GREEN

WHITE

PURPLE PURPLE

RED

BLACK

GRN/YELLOW

YELLOW

GREEN

RED

GREEN

GND

24 VAC

IND

PSW

IGN

FC-

FC+

LED

Earth Ground

CONTROL BOARD

Chassis Wiring Is 18 AWG / 105 Degrees C / @ 600 Volts

Igniter Wire Is 16 AWG / 25 KVDC / 10 KVDC

Crimp Caps Are # CE5 / 105 Degrees C

SECONDARY - 24V

PRIMARY - 120V

PCB

IND

PCB

IGN

IGNITER/FLAME SENSOR

BURNER

PCB

PSW

PCB

T'STAT (Optional)

JUMPER (Optional)

24 VAC

PCB

PRESSURE SWITCH

PCBPCB

V1 V2

GND

Earth &

Chassis Ground

Replace Any Wiring With Same Ratings

All Quick Connects Are Fully Insulated (Except Igniter)

Line

Load

Blower Motor Cavity

Thermostat

Pressure Switch

Igniter & Flame Sense

BLACK

WHITE

GREEN

WHITE

PURPLE PURPLE

RED

BLACK

GRN/YELLOW

YELLOW

GREEN

RED

GREEN

Above: Connection Diagram

Right: Ladder Diagram

Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater 17

OPERATION

Operation of the Heater

CHILDREN AND ADULTS SHOULD BE ALERTED TO THE

HAZARDS OF HIGH SURFACE TEMPERATURES AND

SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING

IGNITION.

YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED

WHEN THEY ARE IN THE SAME SPACE AS THE HEATER.

CLOTHING OR OTHER FLAMMABLE MATERIALS SHOULD

NOT BE HUNG FROM THE HEATER, OR PLACED ON OR

NEAR THE HEATER.

ANY GUARD OR OTHER PROTECTIVE DEVICE REMOVED

FOR SERVICING THE HEATER MUST BE REPLACED PRIOR

TO OPERATING THE HEATER.

INSTALLATION AND REPAIR SHOULD BE DONE BY A

QUALIFIED SERVICE PERSON. THE HEATERS SHOULD

BE INSPECTED BEFORE USE AT LEAST ANNUALLY BY A

QUALIFIED SERVICE PERSON. MORE FREQUENT CLEANING

MAY BE REQUIRED AS NECESSARY. IT IS IMPERATIVE

THAT THE CONTROL COMPARTMENT, AIR PASSAGEWAYS

AND BURNER(S) OF THE HEATER ARE KEPT CLEAN.

1. Turn the thermostat up. When the thermostat calls for

heat, the blower motor will energize.

2. When the motor approaches nominal running speed,

the air proving switch closes and activates the ignition

module which in turn initiates the 15 second long

purge.

3. The ignition module then energizes the spark igniter.

4. When sparking begins, the gas valve is energized.

5. If a flame is detected, the gas valve remains open.

When the call for heat is satisfied, and the system

control mechanism de-energizes, the burner line

voltage supply and the gas valve are turned off.

6. If no flame is detected, the gas valve is closed, and

a purge period begins. After the purge period, the

ignition module energizes the spark igniter and the

gas valve. If a flame is still not established, a third and

final purge/ignition sequence is begun. After three

failed attempts, the system control mechanism will lock

out for a period of one hour, or until the unit is reset.

Reset is accomplished by removing power from the

heater for at least five seconds.

7. Periodically visually check of burner flame while unit is

in operation through sight glass in the side of unit.

MAINTENANCE

Pre-Season Maintenance

Heater area to be kept clear and free from combustible

materials, gasoline, and other flammable vapors and

liquids.

Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect the

appliance and replace any part of the control system and

any gas control which has been under water.

(CAUTION) Label all wires prior to disconnection when

servicing controls. Wiring errors can cause improper and

dangerous operation.

For best performance, the following maintenance

procedures should be performed by a qualified service

agency before each heating season:

1. A qualified service agency should be contacted for

service other than routine maintenance.

2. Check condition of blower scroll and motor. Dirt and

dust may be blown out with compressed air, or a

vacuum cleaner may be used.

3. Check the condition of the burner. Carefully remove

any dust or debris from inside burner.

4. Inspect the igniter. Replace igniter if there is excessive

carbon residue, erosion of electrodes or other defects.

5. Check to see that the burner observation window is

clean and free of cracks or holes. Clean or replace as

required.

6. Check the flue pipe for soot, dirt, or obstructions. The

flow of combustion and ventilation air should not be

obstructed. After cleaning as necessary, re-attach the

flue pipe to the heater.

7. Outside surfaces of heater reflector may be cleaned by

wiping with a damp cloth.

8. Check vent terminal and outside air inlet to see that

they have not become blocked during the non-heating

season If either pipe is restricted, the air switch won’t

close, resulting in a non-heat situation.

9. Verify proper operation after service.

Proper Operating Flame

IGNITER

TUBE SET

BURNER FLAME SHOULD BE

A STRONG BLUE FLAME WITH

LITTLE TO NO YELLOW

BURNER CUP

18 Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater

TROUBLESHOOTING

This troubleshooting guide has been designed to assist you in locating and correcting minor problems that may occur with

the GSP tube heater.

BLOWER DOES NOT COME ON

Possible Cause Try This...

Power cord is not plugged in Plug power cord into a grounded three prong Outlet.

Thermostat setting is too low Increase thermostat temperature setting

DSI module needs to be reset Unplug heater power cord from the electrical Outlet: wait for a minimum of five seconds.

Plug heater cord back into outlet.

No power at electrical outlet Replace fuse or reset circuit breaker

Faulty blower motor Replace blower motor

IGNITER DOES NOT SPARK

Possible Cause Try This...

DSI module needs to be

reset

Unplug heater power cord from the electrical outlet: wait for a minimum of five seconds. Plug

heater cord back into outlet

Faulty igniter or ignition

wire

Unplug heater power cord from the electrical outlet; check igniter and ignition wire for dam-

age. If damaged, replace igniter and/or ignition cable.

Air switch does not oper-

ate

Check flue/air supply duct for obstructions; remove obstructions as required. Check for loose/

leaky air hoses to the air switch; repair/replace/tighten hoses as required. Check for 24V

across the secondary terminals of the transformer.

IF NO: Check for 120V across the primary terminals 1 and 3 (black and white wires) of the

transformer. If 120V is present, replace transformer. If 120 is not present, check wiring

between power cord, blower motor and transformer.

IF YES: Connect a jumper wire across air switch terminals; if jumper wire allows blower to

operate, replace pressure switch (see replacement parts list for part number that applies to

your unit rating).

Igniter spark gap incorrect Reset spark gap to 1/8” (0.125 inches, 0.3175 cm).

BURNER DOES NOT LIGHT

Possible Cause Try This...

Air in the gas line Purge gas lines

Improper gas inlet pres-

sure

Check gas inlet pressure at the 1/8” NPT plugged tap. Gas inlet pressure should be as follows:

Natural GAS: 5.0” w.c. (1.25 kPa) min; 11.0” W.C. (2.74 kPa) max

LP Gas: 11”w.c. (2.74 kPa) min; 13.0” (3.24 kPa) max

If gas inlet pressure does not meet inlet pressure requirements contact the gas company.

Gas valve does not open Check for 24V across valve terminals.

Check shutoff on valve

IF NO: check wiring between the ignition module and the valve. Repair/replace wires as

required. If wiring is OK, replace ignition module.

IF YES: Replace gas valve.

Low gas outlet pressure Check gas manifold pressure. Measure manifold pressure at the pressure tap on the gas valve.

Check gas manifold pressure. Measure manifold pressure at the pressure tap on the gas valve.

Natural Gas: 4.0” w.c. LP Gas 10.0” w.c. If manifold pressure does not meet requirements,

adjust valve outlet pressure with the adjustment screw on the valve. NOTE: Proper inlet gas

pressure must be verified before performing outlet pressure testing.

BURNER DOES NOT STAY LIT

Possible Cause Try This...

Damaged wires between DSI module and electrode Replace wires as required

Faulty DSI module Replace DSI module

Damaged Electrode Replace Electrode

Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater 19

ILLUSTRATED PARTS

This section provides the part numbers and pictorials for components of the GSP tube heater. Callout letters on the

illustrations are keyed to the associated parts list.

# P/N PART DESCRIPTION QTY

16 0128 NG GAS VALVE 1

6 0129 LP GAS VALVE

203808 GAS VALVE EXTENSION FLANGE 1

302590 VENTURI BURNER 1

460729 SPARK IGNITER 1

505795 NG ORIFICE 1

05747 LP ORIFICE

602970 IGNITION MODULE 1

708364A TRANSFORMER 1

802822 PRESSURE SWITCH 1

902575 MOTOR ADAPTER 1

10 02579 BLOWER MOTOR 1

REF ITEM DESCRIPTION

A02591 GSP45NG (burner Box for (F208850)

02592 GSP45LP (burner Box for (F208851)

B02598 GSP45 tube set

C06014 Hanger

D06016 Hanger Clamp

E06008-9 GSP45 Reflector

F06009 Reflector End Cap

ALL WARRANTY CLAIMS REQUIRE PROOF OF PURCHASE

20 Operating Instructions and Owner’s Manual

Gas-Fired Low-Intensity Infrared Heater

WARNING:

USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS

COULD CAUSE INJURY OR DEATH. REPLACEMENT PARTS ARE ONLY AVAILABLE DIRECT

FROM THE FACTORY AND MUST BE INSTALLED BY A QUALIFIED SERVICE AGENCY.

REPLACEMENT PARTS ORDERING INFORMATION:

PURCHASING: Accessories may be purchased at any HEATSTAR by Enerco local dealer

or direct from the factory

FOR INFORMATION REGARDING SERVICE

Please call Toll-Free 866-447-2194

WWW.HEATSTARBYENERCO.COM

Our office hours are 8:00 AM – 5:00 PM, EST, Monday through Friday.

Please include the model number, date of purchase, and description of problem in all

communication.

LIMITED WARRANTY

The company warrants this product to be free from imperfections in material or

workmanship, under normal and proper use in accordance with instructions of The

Company. Limited 3-Year Warranty on Parts & Burner. Limited 10-Year Warranty on

Tube. The Company, at its option, will repair or replace products returned by the buyer

to the factory, transportation prepaid within said one year period and found by the

Company to have imperfections in material or workmanship.

If a part is damaged or missing, call our Technical Support Department at 866-447-

2194.

Address any Warranty Claims to the Service Department, Enerco Group, Inc., 4560 W.

160TH ST., Cleveland, Ohio 44135. Include your name, address, telephone number,

serial number off heater and include details concerning the claim. Also, supply us with

the purchase date and the name and address of the dealer from whom you purchased

our product.

The foregoing is the full extent of the responsibility of the Company. There are no other

warranties, express or implied. Specifically there is no warranty of fitness for a particular

purpose and there is no warranty of merchantability. In no event shall the Company be

liable for delay caused by imperfections, for consequential damages, or for any charges

of the expense of any nature incurred without its written consent. The cost of repair

or replacement shall be the exclusive remedy for any breach of warranty. There is no

warranty against infringement of the like and no implied warranty arising from course

of dealing or usage of trade. This warranty will not apply to any product which has been

repaired or altered outside of the factory in any respect which in our judgment affects

its condition or operation.

Some states do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you. This Warranty gives

you specific legal rights, and you may have other rights which vary from state to state.

ANSI Z83.20-2016

CSA 2.34-2016

OPERATING INSTRUCTIONS

AND OWNER’S MANUAL

MODEL#

45GSP

ENERCO Technical Products, Inc., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 866-447-2194

HEATSTAR is a registered trademarks of ENERCO Technical Products, Inc.

Enerco Group, Inc. reserves the right to make changes at any time, without notice or

obligation, in colors, specifications, accessories, materials and models.

La page charge ...

HeatStar HS45GSP Le manuel du propriétaire

Marque: HeatStar

Modèle: HS45GSP

Catégorie: Chauffe-eau

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: HeatStar HS45GSP Owner's manual
español: HeatStar HS45GSP El manual del propietario

HeatStar HS45GSP Le manuel du propriétaire

HeatStar HS45GSP Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents