Sharp LL-T2015 Le manuel du propriétaire

LCD Monitor

LCD Farbmonitor

Moniteur LCD

Monitor LCD

LL-T2015

OPERATION MANUAL

BEDIENUNGSANLEITUNG

MODE D'EMPLOI

MANUALE D'USO

MANUAL DE FUNCIONAMIENTO

Table of Contents/Inhaltsverzeichnis/Table des matières/Indice/Índice

Notice for Users in the USA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Notice for Users in Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Notice for Users in the UK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Notice for Users in Australia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

TCO'03 (LL-T2015-H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

TCO'99 (LL-T2015-B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Español. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

3

EnglishDeutschFrançaisItalianoEspañolEnglish

Notice for Users in the USA

FCC Statement

WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment

not expressly approved by the manufacturer could void the user's authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the distance between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

Use nothing but the included cables and AC cord to insure compliance with FCC regulation for Class B

computing equipment.

Declaration of Conformity

SHARP LCD Color Monitor LL-T2015-H/LL-T2015-B

This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1)

this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Responsible Party: SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430

TEL: 1-800-BE-SHARP

* As an ENERGY STAR

®

Partner, SHARP has determined that this product meets the ENERGY

STA R

®

guidelines for energy efficiency.

This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury.

Disposal of these materials may be regulated due to environmental considerations. For disposal or

recycling information, please contact your local authorities or the Electronics Industries

Alliance: www.eiae.org

IMPORTANT:

To aid in reporting in case of loss or theft, please

record the monitor's model and serial numbers in

the space provided. The numbers are located on

the rear of the monitor.

Model No.:

Serial No.:

4

Notice for Users in Europe

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended

by 93/68/EEC.

Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit

Änderung 93/68/EWG.

Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées

par la directive 93/68/CEE.

Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/

EEG.

Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.

Quest' apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata

dalla direttiva 93/68/EEC.

        ï   

 ó     ó   

Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão

corrigida pela directiva 93/68/CEE.

Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por

medio de la 93/68/CEE.

Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som komplette ras

av 93/68/EEC.

Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.

Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/

68/EEC.

CAUTION:

TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD BEFORE SERVICING.

CAUTION:

FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN PLUG.

VORSICHT:

UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER HERAUSZIEHEN

ENTFERNEN.

ATTENTION :

POUR UN ARRET TOTAL DE L'APPAREIL, DEBRANCHEZ LA PRISE DU COURANT SECTEUR.

VARNING:

FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH.

PRECAUCION:

PARA UNA COMPLETA DESCONEXION ELECTRICA DESENCHUFE LA CLAVIJA DE LA RED.

PRECAUCION:

A FIN DE EVITAR DESCARGAS ELÉCTRICAS, DESCONECTE EL ENCHUFE DE LA RED ANTES DE

REALIZAR CUALQUIER OPERACIÓN DE SERVICIO.

ATTENZIONE:

PER EVITARE FOLGORAZIONI, SCOLLEGATE IL CAVO DI COLLEGAMENTO ALLA RETE IN

ALTERNATA PRIMA DI EFFETTUARE UN INTERVENTO DI SERVIZIO TECNICO.

ATTENZIONE:

PER UNO SCOLLEGAMENTO ELETTRICO COMPLETO, TIRATE FUORI LA SPINA PRINCIPALE.

5

EnglishDeutschFrançaisItalianoEspañolEnglish

Notice for Users in the UK

Notice for Users in Australia

Service Inquiries

Please contact your dealer for service if required or contact Sharp Corporation of Australia on

1 300 13 50 22 for referral to your nearest Sharp authorized Service Center.

FOR CUSTOMERS IN U.K.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:

GREEN-AND-YELLOW : Earth

BLUE : Neutral

BROWN : Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured

markings identifying the terminals in your plug proceed as follows:

• The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug

which is marked by the letter E or by the safety earth or coloured green or green-and-yellow.

• The wire which is coloured BLUE must be connected to the terminal which is marked with the

letter N or coloured black.

• The wire which is coloured BROWN must be connected to the terminal which is marked with the

letter L or coloured red.

Ensure that your equipment is connected correctly. If you are in any doubt consult a qualified

electrician.

"WARNING: THIS APPARATUS MUST BE EARTHED."

6

Congratulations!

The display you have just purchased carries the TCO'03 Displays

label. This means that your display is designed, manufactured and

tested according to some of the strictest quality and environmental

requirements in the world. This makes for a high performance product,

designed with the user in focus that also minimizes the impact on our

natural environment.

Some of the features of the TCO'03 Display requirements:

Ergonomics

• Good visual ergonomics and image quality in order to improve the working environment for the user

and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution,

reflectance, colour rendition and image stability.

Energy

• Energy-saving mode after a certain time – beneficial both for the user and the environment

• Electrical safety

Emissions

• Electromagnetic fields

• Noise emissions

Ecology

• The product must be prepared for recycling and the manufacturer must have a certified environmental

management system such as EMAS or ISO 14 001

• Restrictions on

- chlorinated and brominated flame retardants and polymers

- heavy metals such as cadmium, mercury and lead.

The requirements included in this label have been developed by TCO Development in cooperation with

scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO

has been involved in influencing the development of IT equipment in a more user-friendly direction. Our

labelling system started with displays in 1992 and is now requested by users and IT-manufacturers all

over the world.

For more information, please visit

www.tcodevelopment.com

LL-T2015-H

7

EnglishDeutschFrançaisItalianoEspañolEnglish

LL-T2015-B

Congratulations!

You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a

product developed for professional use. Your purchase has also contributed to reducing the burden on

the environment and also to the further development of environmentally adapted electronics products.

Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an established method for encouraging the

adaptation of goods and services to the environment. The main problem, as far as computers and other

electronics equipment are concerned, is that environmentally harmful substances are used both in the

products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority

of electronics equipment, most of these potentially damaging substances sooner or later enter nature.

There are also other characteristics of a computer, such as energy consumption levels, that are important

from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of

electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing

emissions, radioactive waste), it is vital to save energy. Electronics equipment in offices is often left

running continuously and thereby consumes a lot of energy.

What does labelling involve?

This product meets the requirements for the TCO'99 scheme which provides for international and

environmental labelling of personal computers. The labelling scheme was developed as a joint effort by

the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen

(The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National

Energy Administration).

Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of

electric and magnetic fields, energy consumption and electrical and fire safety.

The environmental demands impose restrictions on the presence and use of heavy metals, brominated

and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The

product must be prepared for recycling and the manufacturer is obliged to have an environmental policy

which must be adhered to in each country where the company implements its operational policy.

The energy requirements include a demand that the computer and/or display, after a certain period of

inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to

reactivate the computer shall be reasonable for the user.

Labelled products must meet strict environmental demands, for example, in respect of the reduction of

electric and magnetic fields, physical and visual ergonomics and good usability.

Below you will find a brief summary of the environmental requirements met by this product. The complete

environmental criteria document may be ordered from:

TCO Development

SE-114 94 Stockholm, Sweden

Fax: +46 8 782 92 07

Email (Internet): [email protected]

Current information regarding TCO'99 approved and labelled products may also be

obtained via the Internet, using the address: http://www.tco-info.com/

8

Environmental requirements

Flame retardants

Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their

purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing

can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those

flame retardants are chemically related to another group of environmental toxins, PCBs. Both the flame

retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health

effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative*

processes. Flame retardants have been found in human blood and researchers fear that disturbances in

foetus development may occur.

The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not

contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the

printed circuit boards since no substitutes are available.

Cadmium**

Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer

displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99

requirement states that batteries, the colour-generating layers of display screens and the electrical or

electronics components must not contain any cadmium.

Mercury**

Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic

in high doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It

also demands that mercury is not present in any of the electrical or electronics components associated

with the labelled unit. There is however one exception. Mercury is, for the time being, permitted in the

back light system of flat panel monitors as there today is no commercially available alternative. TCO

aims on removing this exception when a mercury free alternative is available.

CFCs (freons)

The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the

manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit

boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing

increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant

melanoma) as a consequence.

Lead**

Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous

system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement permits the

inclusion of lead since no replacement has yet been developed.

*

Bio-accumulative is defined as substances which accumulate within living organisms.

**

Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.

9

EnglishDeutschFrançaisItalianoEspañolEnglish

Table of Contents

Tips and safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Height adjustment, angle adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connecting the monitor and turning the monitor on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connecting the monitor to a computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connecting the monitor to a power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Turning the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Changing between input terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Turning the power off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Adjusting the screen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Adjustment value reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Adjustment lock function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Adjusting the backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Setting display mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Checking product information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Adjusting the screen display (With analog connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Automatic screen adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Manual screen adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Adjusting the screen display (With digital connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Monitor care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Monitor care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Information for customers on environmentally friendly disposal of this SHARP product . . . . . . . . . 29

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Installing set-up information and the ICC profile (For Windows) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Information about the ColorSync profile (For MacOS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Instructions for attaching a VESA-compliant arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

10

Tips and safety precautions

The Power Cord

- Do not damage the power cord nor place heavy

objects on it, stretch it or over bend it. Also, do

not add extension cords. Damage to the cord

may result in fire or electric shock.

- Use only the power cord supplied with the monitor.

- Insert the power plug directly into the AC outlet.

Adding an extension cord may lead to fire as a

result of overheating.

- Do not remove or insert the power plug with wet

hands. Doing so could result in electric shock.

Monitor and accessory checklist

- Please check that the following items are

included in the package:

- LCD monitor (1)

- Analog signal cable (1)

(model name: QCNW-1041MPZZ)

- Digital signal cable (1)

(model name: QCNW-1088MPZZ)

- CD-ROM (1)

- Operation manual (1)

Notes:

- The analog signal cable (DVI-I29 pin - mini D-

sub15 pin) is to be purchased separately.

(model name: NL-C02E)

- The 2-input cable (DVI-I29 pin - DVI-D24 pin/

mini

D-sub15 pin) is to be purchased separately.

(model name: NL-C03J)

- Be sure to use cables that are less than 3 m in

length.

- You are advised to retain the carton in case the

monitor needs to be transported.

- Sharp Corporation holds authorship rights to the

Utility Disk program. Do not reproduce it without

permission.

- The shape of the supplied accessories may not

be exactly same as shown in this manual.

Manual Scope

- In this manual, Microsoft Windows XP will be

referred to as "Windows XP", Microsoft Windows

Millennium as "Windows Me", Microsoft

Windows 2000 as "Windows 2000", Microsoft

Windows 98 as "Windows 98", Microsoft

Windows 95 as "Windows 95", and Microsoft

Windows Version 3.1 as "Windows 3.1". When

there is no need to distinguish between

programs, the term "Windows" will be used.

- Microsoft and Windows are registered

trademarks of Microsoft Corporation.

- Macintosh is a registered trademark of Apple

Computer, Inc.

- All other brand and product names are

trademarks or registered trademarks of their

respective holders.

- The TFT color LCD panel used in this monitor is

made with the application of high precision

technology. However, there may be minute

points on the screen where pixels never light or

are permanently lit. Also, if the screen is viewed

from an acute angle there may be uneven colors

or brightness. Please note that these are not

malfunctions but common phenomena of LCDs

and will not affect the performance of the

monitor.

- Do not display a still picture for a long time, as

this could cause an afterimage to remain.

- If the brightness is adjusted to the minimum

setting it may be difficult to see the screen.

- The quality of the computer signal may influence

the quality of the display. We recommend using

a computer able to emit high quality video

signals.

- Never rub or tap the monitor with hard objects.

- Please understand that Sharp Corporation bears

no responsibility for errors made during use by

the customer or a third party, nor for any other

malfunctions or damage to this product arising

during use, except where indemnity liability is

recognized under law.

- This monitor and its accessories may be

upgraded without advance notice.

Location

- Do not use the monitor where ventilation is poor,

where there is a lot of dust, where humidity is high,

or where the monitor may come into contact with

oil or steam, as this could lead to fire.

- Ensure that the monitor does not come into

contact with water or other fluids. Ensure that no

objects such as paper clips or pins enter the

monitor as this could lead to fire or electric

shock.

- Do not place the monitor on top of unstable

objects or in unsafe places. Do not allow the

monitor to come into contact with strong shocks

or vibrations. Causing the monitor to fall or

topple over may damage it.

- Do not use in places where the monitor will be

subject to direct sunlight, near heating

equipment or anywhere else where there is

likelihood of high temperature, as this may lead

to generation of excessive heat and outbreak of

fire.

- When carrying the monitor, firmly grasp both the

display and stand section. If the monitor is lifted

by the display only, the stand may abruptly pop

out or move, and this could lead to injury. If the

monitor is inclined, the stand may move and

cause injury.

- Be careful not to allow your fingers to be

pinched between the display and stand.

(Especially in the area of attachment.)

11

EnglishDeutschFrançaisItalianoEspañolEnglish

Product description

1

2 3 4 5 6

7

11

12

10

8

9

1. INPUT button .............................. To switch between the signal's input terminals.

2. MENU button .............................. This button is used to pop-up, select and close the OSD (On Screen

Display) Menu.

3.

/ MODE button ........................ When the OSD Menu is displayed:

This button is used to select menu options.

When the OSD Menu is not displayed:

This button is used to set DISPLAY MODE.

4. buttons ................................ When the OSD Menu is displayed:

These buttons are used to select an option or adjust the value of

the selected option.

When the OSD Menu is not displayed:

These buttons are used to adjust backlight brightness.

5. Power button ............................... Pressing this button turns the power on.

Press the button again to turn the power off.

6. Power LED.................................. This LED is lit green when in use and orange when in power-saving

mode.

7.

DVI-I input terminal (INPUT-2) ......

The computer's digital RGB output terminal or analog RGB output

terminal can be connected here.

For a digital signal input: It can be connected to a computer with a

DVI-compatible output terminal (DVI-D24 pin or DVI-I29 pin) and

which has UXGA output ability. Depending on the computer to be

connected, correct display may or may not be possible.

8.

Analog RGB input terminal (INPUT-1)

.... The analog signal cable is connected here. The analog signal cable

included should be used.

9. Security lock anchor ................... By connecting a security lock (commercially available) to the

security lock anchor, the monitor is fixed so that it cannot be

transported.

The security slot works in conjunction with Kensington Micro Saver

Security Systems.

10. Power terminal

11. Main power switch

12. Ventilation openings .................. Note: Never block the ventilation openings as this may lead to

overheating inside the monitor and result in malfunction.

12

Height adjustment, angle adjustment

CAUTION!

- Be sure to hold both sides of the monitor when

adjusting the viewing angle. The LCD panel

used in this monitor is made of glass. Pressure

from hands on the LCD panel could cause

damage.

- Be careful not to allow your fingers to be

pinched.

Height adjustment

Adjust to an easy to view height.

approx. 60 mm

Angle adjustment

Adjust to an easy to view angle.

Note:

- Tilt of the display can be finely adjusted.

approx. 1.0°

approx. 30°

approx. 45°

approx. 5°

approx. 45°

13

EnglishDeutschFrançaisItalianoEspañolEnglish

Connecting the monitor and turning the monitor on and off

CAUTION!

- When connecting, ensure that both the monitor

and computer are switched off.

- Be careful not to over bend the cable or add

extension cords as this could lead to a

malfunction.

Cable storage

If necessary, excess cable can be housed in the

stand.

1.Remove the cover.

Gently pull the top of the cover towards yourself.

2.Run cable along the back of the stand.

3.Refit the cover.

Be careful not to pinch the cable.

- If the cover is hard to refit, do not force it.

Check whether cables are trapped.

14

Connecting the monitor and turning the monitor on and off

Digital connection

Connect the accessory digital signal cable to the

digital RGB output terminal of the computer.

- The monitor has an input for connecting to a

computer with a DVI-compatible output

connector (DVI-D24 pin or DVI-I29 pin) and

UXGA output capability. (Depending on the type

of computer to be connected, the display may

not work correctly.)

- Use the accessory digital signal cable.

If using other commercially available digital

signal cables, correct display may not be

achieved.

- Paying attention to connector direction, firmly

insert the signal cable to terminal, and then

tighten the screws at both sides.

Set the monitor as follows when establishing a

digital connection with a Power Mac using an ADC-

DVI adapter made by Belkin. (Operation has been

checked with the Power Mac G4 M7627J/A.)

- Perform settings with the Power Mac power

supply off.

1.After connecting the power cord, turn on the

monitor's main power.

2.Press the button and button simultaneously,

and while doing this press the power button (i.e.

turn the power on).

MAC DIGITAL

INPUT-2 OFF ON

3.Set to [ON] with the buttons.

- Do not set to [ON] if you are not using a Belkin

ADC-DVI adapter, as this may result in

incorrect display.

4.Press the MENU button.

This completes setting.

Digital signal cable

Digital RGB output

terminal

DVI-I input terminal

(INPUT-2)

Connecting the monitor to a computer

The accessory signal cable enables connection of

two computers.

(One analog and one digital connection.)

-

The separately sold 2-input cable enables connection of

two computers to the DVI-I input terminal.

- When using the 2-input cable, set the

connecting input terminal [INPUT-2] to [2LINES]

under the MODE SELECT-2 Menu. (p.24, 27)

Analog connection

Connect the accessory analog signal cable, or

separately-sold analog signal cable (model name:

NL-C02E) to the analog RGB output terminal of

the computer.

- Connect the accessory analog signal cable to

the analog RGB input terminal (INPUT-1).

- Connect the separately-sold analog signal cable

(model name: NL-C02E) to the DVI-I input

terminal (INPUT-2).

- Paying attention to connector direction, firmly

insert the signal cable to terminal, and then

tighten the screws at both sides.

If connecting to a D-sub15 pin 2 row Apple Power

Macintosh, attach a Macintosh conversion adapter

(commercially available) to the analog signal cable.

Note:

- If connecting to the Sun Ultra series, a

conversion adapter (commercially available)

may be required.

Analog signal cable

Analog RGB output

terminal

DVI-I input terminal

(INPUT-2)

Analog RGB

input terminal

(INPUT-1)

Macintosh conversion adapter

15

EnglishDeutschFrançaisItalianoEspañolEnglish

Connecting the monitor and turning the monitor on and off

Connecting the monitor to a power

source

When connecting using a separately sold 2-

input cable

The separately sold 2-input cable (model name:

NL-C03J) enables connection between the DVI-I

input terminal on the monitor and the two PCs.

(One analog and one digital connection.)

1.Connect the 2-input cable to the DVI-I input

terminal of the monitor.

2.Connect the accessory or commercially

available analog signal cable and the accessory

digital signal cable to the 2-input cable.

- When using commercially available analog

signal cable, both ends should be mini D-sub

15 pin.

3.Connect each signal cable to the computers.

- Paying attention to connector orientation,

firmly insert the signal cable into the PC, and

then tighten the screws at both sides.

Notes:

- When using the 2-input cable, set the

connecting input terminal [INPUT-2] to [2LINES]

under the MODE SELECT-2 Menu. (p.24, 27)

- The monitor connected to the 2-input cable by

analog connection may not be automatically

recognized and setup under Plug & Play.

Perform storage of setup information manually.

(p.33)

DVI-D24 pin

2-input cable

(purchased separately)

mini D-sub15 pin

DVI-I input terminal

(INPUT-2)

Digital RGB output terminal

Digital signal cable

Analog signal cable

Analog RGB

output terminal

Power terminal

Power cord

AC outlet

16

Turning the power on

1.Turn on the main power of the monitor.

- When switching the main power switch on and

off, always wait for an interval of at least 5

seconds. Rapid switching may result in

malfunction.

2.Press the monitor's power button.

The power LED will light up orange.

3.Turn on the computer.

ON

When a signal is input from the computer, the

power LED lights up green, and the screen is

displayed. (After power is turned on, it may take

a little time until the screen is displayed.)

- If the input terminal to which the computer is

connected has not been selected, the screen

will not be displayed. If necessary, perform

input terminal switching. (right column)

Notes:

- When using an analog signal, perform an

automatic screen adjustment under the following

conditions (p.20):

- Using the monitor for the first time.

- After having changed the system settings

during use.

- Depending on the type of computer or OS, you

may need to install the monitor set-up

information on your system. (p.33)

- When connecting to a notebook, if the notebook

computer's screen is set to display at the same

time, the MS-DOS screen may not display

properly. In this case, change the setting to

display only the LCD monitor.

Turn on the

computer power

supply.

Press power button.

Changing between input terminals

Use the INPUT button to switch between signal

input terminals.

When not using a 2-input cable

Analog RGB input terminal

DVI-I input terminal

INPUT-1

INPUT-2

< >

INPUT

When using a 2-input cable

Analog RGB input terminal

INPUT2-A

INPUT2-D

INPUT

INPUT-1

INPUT

Note:

- When there is no input signal, [NO SIGNAL] is

displayed.

Connecting the monitor and turning the monitor on and off

Main power switch

DVI-I input terminal

(analog)

DVI-I input terminal

(digital)

17

EnglishDeutschFrançaisItalianoEspañolEnglish

Turning the power off

1. Turn the computer off.

2.Press the monitor's power button.

The power LED will disappear.

OFF

If the monitor will not be used for a long time, turn

off the main power switch of the monitor, and

remove the power plug from the outlet.

Press power button.

Turn the computer

off.

Connecting the monitor and turning the monitor on and off

18

Adjusting the screen display

For analog signal

1.First perform an automatic adjustment. (p.20)

2.Perform manual adjustment where necessary.

(p.21)

For digital signal

The monitor can generally be used without

adjustment. If necessary perform manual

adjustment. (p.25)

Note:

- All adjustments will be saved even after turning

the power off.

Adjustment value reset

Resetting all adjustment values

All adjustment values can be returned to their

original ex-factory values in one command.

1. Turn off the monitor power.

2.Press the MENU button and the / MODE

button simultaneously, and while doing this

press the power button (i.e. turn the power on).

Continue to press the buttons until [ALL RESET]

appears on the screen. Reset is complete when

the displayed message disappears.

Notes:

- While [ALL RESET] is displayed, the control

buttons are disabled.

- It is not possible to reset values when the

adjustment lock is in place. Remove the

adjustment lock before attempting to operate

control buttons.

ADJUSTMENT Menu reset

Settings of items in the ADJUSTMENT Menu

(CLOCK, PHASE, H-POS, V-POS) can be returned

to their original ex-factory values.

1.Turn on the monitor power.

2. Press the MENU button and the button

simultaneously. When [RESET] appears on the

screen, the reset is complete.

Notes:

- While [RESET] is displayed, the control buttons

are disabled.

- It is not possible to reset values when the

adjustment lock is in place. Remove the

adjustment lock before attempting to operate

control buttons.

Adjustment lock function

By disabling the control buttons (i.e. setting the

lock) any attempted changes to adjusted values will

be voided.

1. Turn off the monitor power.

2.While pressing the MENU button, press the

power button (i.e. turn the power on).

Continue to press the buttons until

[

ADJUSTMENT LOCKED

] appears on the

screen. The lock is set when the message is

displayed.

Note:

- When the lock is in place, all buttons other than

the power button are disabled.

Adjustment lock release

1. Turn off the monitor power.

2.While pressing the MENU button, press the

power button (i.e. turn the power on).

Continue to press the buttons until

[

ADJUSTMENT UNLOCKED

] appears on the

screen. The lock is released when the message

is displayed.

Adjusting the backlight

1.Without the OSD Menu being displayed, press

the or the button.

BR

I

GHT 31

+

-

2.Adjust by pressing the button (darker) or

button (lighter).

Note:

- On Screen display for adjustment disappears

several seconds after the last operation.

19

EnglishDeutschFrançaisItalianoEspañolEnglish

Setting display mode

Color tone or brightness can be changed with one

command.

STD

Displays image with the color tone results from

original scheme of liquid crystal panel.

OFFICE

Display brightness is lowered. (This mode saves

power.)

sRGB

sRGB is international standard of color

representation specified by IEC (International

Electrotechnical Commission).

Color conversion is made in taking account of

liquid crystal's characteristics and represents

color tone close to its original image.

VIVID

Displays an image with dynamic and vivid

primary colors.

- If [DISPLAY MODE] is set to [sRGB] or [VIVID],

[WHITE BALANCE] is set to [STD].

How to set

Press the / MODE button when the OSD Menu is

not displayed.

Each time the button is pressed the next menu

item appears. (STD  OFFICE  sRGB  VIVID

 STD)

On Screen display for adjustment disappears

several seconds after the last operation.

Checking product information

A model name (MODEL), a serial no. (S/N), and

usage time (USAGE TIME) of the monitor can be

checked.

1.Turn the power off.

2.While pressing the / MODE button, press the

monitor's power button (i.e. turn the power on).

3.Checking done: MENU button

Note:

- Please note that the indication of usage time at

purchase may not be 0 (zero), as a result of

factory inspection and other activities during

manufacture.

Adjusting the screen display

20

Adjusting the screen display (With analog connection)

Automatic screen adjustment

Options in the ADJUSTMENT Menu can be

adjusted automatically (CLOCK, PHASE, H-POS,

V-POS).

Note:

- When setting up this monitor for the first time or

after having changed an aspect of the current

system, perform an automatic screen adjustment

before use.

On Screen Display for the automatic adjustment

First display an image that makes the entire

screen light.

If you are using Windows, you can use the

Adjustment Pattern on the accompanying CD-ROM.

Opening the Adjustment Pattern (for Windows)

This explanation is for Windows 95/98/2000/Me/

XP, and assumes that the CD-ROM drive is "D"

drive.

1.Load the accessory CD-ROM into the CD-ROM

drive of the computer.

2.Open [My Computer] and select CD-ROM. If

using Windows 3.1, open [File Manager] and

choose "D" drive.

3.Double click on [Adj_uty.exe] to run the

Adjustment Program. The Adjustment Pattern

will appear.

Adjustment Pattern

After completing the adjustments, press the

computer's [Esc] key to exit the Adjustment

Program.

Note:

- If your computer's display mode is set to 65K

colors, you may see the different color levels in

each color pattern or the gray scale may look

colored. (This is due to the specification of the

input signal and is not a malfunction.)

Adjusting the screen automatically

1.Press the MENU button.

The ADJUSTMENT Menu will be displayed.

ADJUSTMENT

MANUAL AUTO

CLOCK 127

PHASE 0

H-POS 250

V-POS 48

INPUT-1 ANALOG

1600 x 1200 V:60Hz H:75.0kHz

+

-

+

-

+

-

+

-

2.Press the button.

The screen will become dark and [ADJUSTING]

will be displayed. After a few seconds the

ADJUSTMENT Menu will return. (The automatic

adjustment is now complete.)

3.Press the MENU button 5 times to make the OSD

(On Screen Display) Menu disappear.

Notes:

- In most cases automatic adjustment is sufficient.

- It may not be possible to achieve correct

adjustment with the first automatic adjustment. In

such a case, try repeating the automatic

adjustment 2 or 3 times.

- If necessary due to any of the following, manual

adjustments (p.21) can be performed after the

automatic adjustment:

- When further fine adjustment is needed.

- When [OUT OF ADJUST] is displayed. (When

the screen displays an entirely dark image, the

automatic screen adjustment may be disabled.

When making an automatic adjustment, be

sure to either use the Adjustment Pattern or try

displaying an image that makes the entire

screen very bright.)

- When the computer's video input signals are

Composite Sync or Sync on Green. (Automatic

adjustments may not be possible.)

- Automatic adjustment may not be achieved

correctly depending on what is displayed on the

screen - moving pictures or the MS-DOS prompt

etc.

La page charge ...

Sharp LL-T2015 Le manuel du propriétaire

Sharp LL-T2015 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents