Sharp Computer Monitor LL-T1815 Manuel utilisateur

LCD Monitor

LCD Farbmonitor

Moniteur LCD

Monitor LCD

LL-T1815

OPERATION MANUAL

BEDIENUNGSANLEITUNG

MODE D’EMPLOI

MANUALE D’USO

MANUAL DE FUNCIONAMIENTO

Table of Contents / Inhaltsverzeichnis / Table des matières / Indice / Índice

Notice for Users in Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Notice for Users in the UK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Notice for Users in Australia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Notice for Users in the USA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

TCO’95 / TCO’99 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Deutsch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

3

EnglishDeutschFrançaisItalianoEspañolEnglish

Notice for Users in Europe

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended

by 93/68/EEC.

Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit

Änderung 93/68/EWG.

Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées

par la directive 93/68/CEE.

Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/

EEG.

Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.

Quest' apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata

dalla direttiva 93/68/EEC.

Η εγκατασταση ανταποκρινεται στιζ απαιτησειζ των οδηγιων τηζ Ευρωπαïκηζ Ενωσηζ 89/336/ΕΟΚ κατ

73/23/ΕΟΚ, óπωζ οι κανονισµοι αυτοι συµπληρωθηκαν απó την οδηγια 93/68/ΕΟΚ.

Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão

corrigida pela directiva 93/68/CEE.

Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por

medio de la 93/68/CEE.

Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som komplette ras

av 93/68/EEC.

Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.

Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/

68/EEC.

CAUTION :

TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD BEFORE SERVICING.

CAUTION :

FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN PLUG.

VORSICHT :

UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER HERAUSZIEHEN

ENTFERNEN.

ATTENTION :

POUR UN ARRET TOTAL DE L’APPAREIL, DEBRANCHEZ LA PRISE DU COURANT SECTEUR.

VARNING :

FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH.

PRECAUCION :

PARA UNA COMPLETA DESCONEXION ELECTRICA DESENCHUFE LA CLAVIJA DE LA RED.

PRECAUCION :

A FIN DE EVITAR DESCARGAS ELÉCTRICAS, DESCONECTE EL ENCHUFE DE LA RED ANTES DE

REALIZAR CUALQUIER OPERACIÓN DE SERVICIO.

ATTENZIONE:

PER EVITARE FOLGORAZIONI, SCOLLEGATE IL CAVO DI COLLEGAMENTO ALLA RETE IN

ALTERNATA PRIMA DI EFFETTUARE UN INTERVENTO DI SERVIZIO TECNICO.

ATTENZIONE:

PER UNO SCOLLEGAMENTO ELETTRICO COMPLETO, TIRATE FUORI LA SPINA PRINCIPALE.

4

Notice for Users in the UK

FOR CUSTOMERS IN U.K.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code :

GREEN-AND-YELLOW : Earth

BLUE : Neutral

BROWN : Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured

markings identifying the terminals in your plug proceed as follows. The wire which is coloured

GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E

or by the safety earth or coloured green or green-and-yellow.

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N

or coloured black.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter

L or coloured red.

Ensure that your equipment is connected correctly-if you are in any doubt consult a qualified electri-

cian.

"WARNING :THIS APPARATUS MUST BE EARTHED"

Notice for Users in Australia

Service Inquiries

Please contact your dealer for service if required or contact Sharp Corporation of Australia on

1 300 13 50 22 for referral to your nearest Sharp authorized Service Center.

5

EnglishDeutschFrançaisItalianoEspañolEnglish

Notice for Users in the USA

FCC Statement

WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment

not expressly approved by the manufacturer could void the user's authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be deter-

mined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the distance between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

Use nothing but the included cables and AC cord to insure compliance with FCC regulation for Class B

computing equipment.

Declaration of Conformity

SHARP LCD Color Monitor LL-T1815

This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1)

this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undersized operation.

Responsible Party : SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430

TEL :1-800-BE-SHARP

* As an ENERGY STAR Partner, SHARP has determined that this product meets the ENERGY STAR

guidelines for energy efficiency.

This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury.

Disposal of these materials may be regulated due to environmental considerations. For disposal or

recycling information, please contact your local authorities or the Electronics Industries

Alliance:www.eiae.org

6

LL-T1815-B LL-T1815-H

Congratulations!

You have just purchased a TCO’95 or TCO’99 approved and

labelled product! Your choice has provided you with a

product developed for professional use. Your purchase has

also contributed to reducing the burden on the environment

and also to the further development of environmentally

adapted electronics products.

This product meets the requirements for the TCO’95 or

TCO’99 scheme which provides for an international

environmental and quality labelling of personal computers.

The labelling scheme was developed as a joint effort by the

TCO (The Swedish Confederation of Professional Employ-

ees), Svenska Naturskyddsforeningen (The Swedish Society

for Nature Conservation), Statens Energimyndighet (The

Swedish National Energy Administration) and SEMKO AB.

The requirements cover a wide range of issues: environ-

ment, ergonomics, usability, reduction of electric and

magnetic fields, energy consumption and electrical safety.

Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an

established method for encouraging the adaptation of goods

and services to the environment. The main problem, as far

as computers and other electronics equipment are con-

cerned, is that environmentally harmful substances are

used both in the products and during their manufacture.

Since it is not so far possible to satisfactorily recycle the

majority of electronics equipment, most of these potentially

damaging substances sooner or later enter nature.

There are also other characteristics of a computer, such as

energy consumption levels, that are important from the

viewpoints of both the work (internal) and natural (external)

environments. Since all methods of electricity generation

have a negative effect on the environment (e.g. acidic and

climate-influencing emissions, radioactive waste), it is vital

to save energy. Electronics equipment in offices is often left

running continuously and thereby consumes a lot of energy.

What does the environmenal labelling involve?

The environmental demands has been developed by

Svenska Naturskyddsforeningen (The Swedish Society for

Nature Conservation). These demands impose restrictions

on the presence and use of heavy metals, brominated and

chlorinated flame retardants, CFCs (freons) and chlorinated

solvents, among other things. The product must be

prepared for recycling and the manufacturer is obliged to

have an environmental policy which must be adhered to in

each country where the company implements its opera-

tional policy.

The energy requirements include a demand that the

computer and/or display, after a certain period of inactivity,

shall reduce its power consumption to a lower level in one

or more stages. The length of time to reactivate the

computer shall be reasonable for the user.

Below you will find a brief summary of the environmental

requirements met by this product. The complete environ-

mental criteria document may be ordered from:

TCO Development

SE-114 94 Stockholm, Sweden

Fax: +46 8 782 92 07

Email (Internet): development@tco.se

Current information regarding TCO’99 approved and

labelled products may also be obtained via the Internet,

using the address: http://www.tco-info.com/

Environmental requirements

Flame retardants

Flame retardants are present in printed circuit boards,

cables, wires, casings and housings. Their purpose is to

prevent, or at least to delay the spread of fire. Up to 30% of

the plastic in a computer casing can consist of flame

retardant substances. Most flame retardants contain

bromine or chloride, and those flame retardants are

chemically related to another group of environmental toxins,

PCBs. Both the flame retardants containing bromine or

chloride and the PCBs are suspected of giving rise to

severe health effects, including reproductive damage in fish-

eating birds and mammals, due to the bio-accumulative *

processes. Flame retardants have been found in human

blood and researchers fear that disturbances in foetus

development may occur. The relevant TCO´95 and TCO’99

demand require that plastic components weighing more

than 25 grams must not contain flame retardants with

organically bound bromine or chlorine. Flame retardants are

allowed in the printed circuit boards since no substitutes are

available.

Cadmium **

Cadmium is present in rechargeable batteries and in the

colour-generating layers of certain computer displays.

Cadmium damages the nervous system and is toxic in high

doses.

TCO’95 requirement states that batteries may not contain

more than 25 ppm (parts per million) of cadmium. The

colour-generating layers of display screens must not contain

any cadmium.

The relevant TCO’99 requirement states that batteries, the

colour-generating layers of display screens

and the electrical or electronics components must not

contain any cadmium.

Mercury **

Mercury is sometimes found in batteries, relays and

switches. It damages the nervous system and is

toxic in high doses.

TCO’95 requirement states that batteries may not contain

more than 25 ppm (parts per million) of mercury. The

relevant TCO’99 requirement states that batteries may not

contain any mercury.

Both TCO´95 and TCO´99 also demand that mercury is not

present in any of the electrical or electronics components

associated with the labelled unit. There is however one

exception. Mercury is, for the time being, permitted in the

back light system of flat panel monitors as there today is no

commercially available alternative. TCO aims on removing

this exception when a mercury free alternative is available.

CFCs (freons)

The relevant TCO’95 and TCO’99 requirement state that

neither CFCs nor HCFCs may be used during the manufac-

ture and assembly of the product. CFCs (freons) are

sometimes used for washing printed circuit boards. CFCs

break down ozone and thereby damage the ozone layer in

the stratosphere, causing increased reception on earth of

ultraviolet light with e.g. increased risks of skin cancer

(malignant melanoma) as a consequence.

Lead **

Lead can be found in picture tubes, display screens, solders

and capacitors. Lead damages the nervous system and in

higher doses, causes lead poisoning. The relevant TCO’95

and TCO´99 requirement permit the inclusion of lead since

no replacement has yet been developed.

* Bio-accumulative is defined as substances which

accumulate within living organisms

** Lead, Cadmium and Mercury are heavy metals which are

Bio-accumulative.

7

EnglishDeutschFrançaisItalianoEspañolEnglish

Table of Contents

Tips and safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Height adjustment, angle adjustment, rotation (long height/width) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting the monitor and turning the monitor on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connecting the monitor to a computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connect the accessory audio cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connection of headphones (commercially available) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connecting the monitor to a power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Turning the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Changing between input terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Turning the power off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Adjusting the screen display and speaker volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Adjustment value reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Adjustment lock function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Adjusting the backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Adjusting the speaker volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Checking product information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Adjusting the screen display (With analog connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Automatic screen adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Manual screen adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Adjusting the screen display (With digital connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Monitor care and repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Monitor care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Installing set-up information and the ICC profile (For Windows) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Information about the ColorSync profile (For MacOS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Instructions for attaching a VESA compliant arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Information about the Pivot Software (Long height/width display) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

8

Tips and safety precautions

The Power Cord

- Do not damage the power cord nor place heavy

objects on it, stretch it or overly bend it. Also, do

not add extension cords. Damage to the cord

may result in fire or electric shock.

- Insert the power plug directly into the AC outlet.

Adding an extension cord may lead to fire as a

result of overheating.

Monitor and accessory checklist

- Please check that the following items are

included in the package.

- LCD monitor (1)

- Analog signal cable (1)

(model name: QCNW-1041MPZZ)

- Audio cable (1)

(model name: QCNW-1068MPZA)

- CD-ROM (1)

- Cleaning cloth (1)

- Operation manual (1)

Notes:

- The digital signal cable (DVI-D24 pin – DVI-D24

pin) is to be purchased separately.

(model name: NL-C01E)

- The analog signal cable (DVI-I29 pin – mini D-

sub 15 pin) is to be purchased separately.

(model name: NL-C02E)

- The 2-input cable (DVI-I29 pin - DVI-D24 pin/mini

D-sub 15 pin) is to be purchased separately.

(model name: NL-C03J)

- You are advised to retain the carton in case the

monitor needs to be transported.

- Sharp Corporation holds authorship rights to the

Utility Disk program. Do not reproduce it without

permission.

- The shape of the supplied accessaries may not

be exactly same as shown in this booklet.

Manual Scope

- In this booklet, Microsoft Windows XP will be

referred to as [WindowsXP], Microsoft Windows

Millenium as [WindowsMe], Microsoft Windows

2000 as [Windows2000], Microsoft Windows 98

as [Windows98], Microsoft Windows 95 as

[Windows95], and Microsoft Windows Version 3.1

as [Windows3.1]. When there is no need to

distinguish between programs, the term

[Windows] will be used.

- Microsoft and Windows are registered

trademarks of Microsoft Corporation.

- Macintosh is a registered trademark of Apple

Computer, Inc.

- Pivot is a registered trademark of Portrait

Displays, Inc.

- The TFT color LCD panel used in this monitor is

made with the application of high precision

technology. However, there may be minute points

on the screen where pixels never light or are

permanently lit. Also, if the screen is viewed from

an acute angle there may be uneven colors or

brightness. Please note that these are not

malfunctions but common phenomena of LCDs

and will not affect the performance of the

monitor.

- Do not leave the screen displaying idly for long

periods of time, as this could cause afterimage to

remain.

- If the brightness is adjusted to the minimum

setting it may be difficult to see the screen.

- The quality of the computer signal may influence

the quality of the display. We recommend using a

computer able to emit high quality video signals.

- Never rub or tap the monitor with hard objects.

- Please understand that Sharp Corporation bears

no responsibility for errors made during use by

the customer or a third party, nor for any other

malfunctions or damage to this product arising

during use, except where indemnity liability is

recognized under law.

- This monitor and its accessories may be

upgraded without advance notice.

Location

- Do not use the monitor where ventilation is poor,

where there is a lot of dust, where humidity is high,

or where the monitor may come into contact with oil

or steam, as this could lead to fire.

- Ensure that the monitor does not come into

contact with water or other fluids. Ensure that no

objects such as paper clips or pins enter the

monitor as this could lead to fire or electric

shock.

- Do not place the monitor on top of unstable

objects or in unsafe places. Do not allow the

monitor to come into contact with strong shocks

or vibrations. Causing the monitor to fall or topple

over may damage it.

- Do not use in places where the monitor will be

subject to direct sunlight, near heating equipment

or anywhere else where there is likelihood of

high temperature, as this may lead to generation

of excessive heat and outbreak of fire.

- When carrying the monitor, firmly grasp both the

display and stand section.If the monitor is lifted

by the display only, the stand may abruptly pop

out or move, and this could lead to injury. If the

monitor is inclined, the stand may move and

cause injury.

- Be careful not to allow your fingers to be pinched

between the display and stand. (Especially in the

area of attachment.)

9

EnglishDeutschFrançaisItalianoEspañolEnglish

Product description

23 4 56

8 11 13

14

12

7

10

15

7

15

9

1

1. INPUT button .............................. To switch between the signal’s input terminals.

2. MENU button............................... This button is used to pop-up, select and close the OSD (On Screen

Display) Menu.

3. button ...................................... This button is used to select menu options when the OSD Menu is

displayed.

4.

buttons ................................ When the OSD Menu is displayed:

These buttons are used to increase or decrease the value of a

selected option.

When the OSD Menu is not displayed:

These buttons are used to adjust backlight brightness and speaker

volume.

5. Power button

6. Power LED .................................. This LED is lit green when in use and orange when in power-saving

mode.

7. Speakers ..................................... Audio entering via the monitor and the external device connected to

the monitor can be heard.

8. Headphone terminal ................... Headphones (commercially available) can be connected here.

9. Audio input terminal .................... A computer’s audio output terminal can be connected here. The

audio cable included should be used.

10. DVI-I input terminal (INPUT-2) .... The computer’s digital RGB output terminal or analog RGB output

terminal can be connected here.

Separately sold cables are necessary for connection. (p.8)

For a digital signal input: It can be connected to a computer with a

DVI-compatible output terminal (DVI-D24 pin or DVI-I29 pin) and

which has SXGA output ability. Depending on the computer to be

connected, correct display may or may not be possible.

11. Analog RGB input terminal ......... The analog signal cable is connected here.The analog signal cable

included should be used.

12. Security lock anchor ................... By connecting a security lock (commercially available) to the security

lock anchor, the monitor is fixed so that it cannot be transported.

The security slot works in conjunction with Kensington Micro Saver

Security Systems.

13. Power terminal

14. Main power switch

15.Ventilation openings .................... Note: Never block the ventilation openings as this may lead to

overheating inside the monitor and result in malfunction.

(INPUT-1)

10

Height adjustment, angle adjustment, rotation

(long height/width)

CAUTION!

- Pressure from hands on the LCD panel could

cause damage.

- Be careful not to allow your fingers to be

pinched.

Height adjustment

Adjust to an easy to view height.

Angle adjustment

Adjust to an easy to view angle.

Approx.80mm

approx.30°

approx.45°

approx.5°

approx.45°

Rotation (long height/width)

The display can be rotated for a long height or

width to suit the displayed content.

- Before rotating, move the display to its

uppermost position. If the display is rotated while

it is set low, it will contact the stand and could

lead to damage.

- The display can only be rotated through a range

of 90°. Applying excessive force may cause

malfunction.

- Do not apply excessive force when the cable is

connected.

To set to long height

Gently turn in the clockwise direction (to 90°).

To set to long width

Gently turn in the counterclockwise direction (to

90°).

Note:

- The orientation of the display can be changed

using Pivot Software. (p. 35)

11

EnglishDeutschFrançaisItalianoEspañolEnglish

Connecting the monitor and turning the monitor on and off

CAUTION!

- When connecting, ensure that both the monitor

and computer are switched off.

- Be careful not to overly bend the cable or add

extension cords as this could lead to a

malfunction.

Cable storage

If necessary, excess cable can be housed in the

stand.

1.Remove the cover.

Gently pull the top of the cover towards yourself.

2.Run cable along the back of the stand.

Pass cable in front of the stand, and then bring it

through the back.

- If the display is to be rotated, first house the

cables with the display in the long height

position, so there is sufficient length when the

display is turned.

3.Refit the cover.

Be careful not to pinch the cable.

- If the cover is hard to refit, do not force it.

Check whether cables are trapped.

CAUTION!

- If the display is to be rotated, first house the

cable, and then check while gently turning the

display. If it cannot be turned, rehouse the cable

with sufficient slack. (If there is insufficient cable

length, rotation will be impossible. Forcing

rotation may cause cable disconnection.)

Connecting the monitor to a computer

Connecting using accessory analog signal

cable

Connect the accessory analog signal cable to the

analog RGB input terminal of the display, and the

analog RGB output terminal of the computer.

- Paying attention to connector direction, firmly

insert the signal cable to terminal, and then

tighten the screws at both sides.

Analog signal cable

Analog RGB output

terminal

Analog RGB input

terminal

12

If connecting to a D-sub 15 pin 2 row Apple Power

Macintosh, attach a Macintosh conversion adapter

(commercially available) to the analog signal cable.

When connecting using separately sold

digital or analog signal cables

The separately sold display cable enables connec-

tion between the DVI-I input terminal on the display

and the digital or analog RGB output terminal of

the computer.

When connecting to a digital RGB output terminal:

- Use a digital signal cable (model name: NL-

C01E)

- For digital RGB connection, the monitor has an

input for connecting to a computer with a DVI-

compatible output connector (DVI-D 24 pin or

DVI-I 29 pin) and SXGA output capability.

(Depending on the type of computer to be

connected, the display may not work correctly.)

When connecting to an analog RGB output terminal:

- Use an analog signal cable (model name: NL-

C02E).

- Paying attention to connector direction, firmly

insert the signal cable to terminal, and then

tighten the screws at both sides.

Note:

- When using digital or analog signal cables, set

[INPUT-2] to [1 LINE]. (p.21, 24)

Connecting the monitor and turning the monitor on and off

Macintosh conversion adapter

Display cable

(purchased separately)

RGB output terminal

DVI-I input terminal

Set the monitor as follows when establishing a

digital connection with a Power Mac using an ADC-

DVI adapter made by Belkin. (Operation has been

checked with the Power Mac G4 M7627J/A)

- Perform settings with the Power Mac power

supply off.

1.After connecting the power cord, turn on the

monitor’s main power.

2.Press the

button and button simultaneously,

and while doing this press the POWER button

(i.e. turn the power on).

MAC DIGITAL

INPUT-2 OFF ON

3.Set to "ON" with the buttons.

- Do not set to [ON] if you are not using a Belkin

ADC-DVI adapter, as this may result in

incorrect display.

4. Press the power button, and turn off the monitor

power.

This completes setting.

When connecting using a separately sold 2-

input cable

The separately sold 2-input cable (model name:NL-

C03J) enables 2 system connection.

1.Connect a 2-input cable (purchased separately)

to the DVI-I input terminal on the display.

2-input cable

(purchased

separately)

DVI-I input terminal

DVI-D24 pin

mini D-sub 15 pin

13

EnglishDeutschFrançaisItalianoEspañolEnglish

Connecting the monitor and turning the monitor on and off

Connection of headphones

(commercially available)

Headphones (commercially available) can be

connected.

Notes:

- When the headphones are connected, no sound

can be heard from the monitor speakers.

Headphones

Connect the accessory audio cable

When the accessory audio cable is connected to

the audio output terminal of the computer, the

sound of the connected computer is output from

the display speakers. You can also use the

headphone jack of the display.

Audio cable

Audio input

terminal

To audio output terminal

Headphone

terminal

Connecting the monitor to a power

source

Power terminal

Power cord

AC outlet

2.Connect the analog and digital signal cables

(purchased separately) to the 2-input cable, then

connect to a computer.

- Paying attention to connector orientation, firmly

insert the signal cable into the PC, and then

tighten the screws at both sides.

Notes:

- When using a 2-input cable, set [INPUT-2] to [2

LINES]. (p. 21, 24)

- The monitor connected to the mini D-sub

connector of the 2-input cable may not be

automatically recognized and setup under Plug &

Play. Perform storage of setup information

manually. (p. 30)

Analog signal cable

Analog RGB

output terminal

Digital signal cable

( NL-C01E, purchased separately)

Digital RGB output terminal

14

Turning the power on

1.Turn on the main power of the monitor.

- When switching the main power switch on and

off, always wait for an interval of at least 5

seconds. Rapid switching may result in

malfunction.

2.Press the monitor's POWER button.

The power LED will light up orange.

3.Turn on the computer.

ON

When a signal is input from the computer, the

power LED lights up green, and the screen is

displayed (After power is turned on, it may take a

little time until the screen is displayed.)

- If the input terminal to which the computer is

connected has not been selected, the screen

will not be displayed. If necessary, perform

input terminal switching. (right column)

Notes: (when using an analog signal)

- If using the monitor for the first time or after

having changed the system settings during use,

perform an automatic screen adjustment (p. 18).

- When connecting to a notebook, if the notebook

computer's screen is set so that it is displaying at

the same time, the MS-DOS screen may not be

able to display properly. In this case, change the

settings so that only the monitor is displaying.

Turn on the

computer power

supply.

Press power button

Main power switch

Changing between input terminals

Use the INPUT button to switch between signal

input terminals.

When not using a 2-input cable

Select [INPUT-1] Select [INPUT-2]

INPUT-1

INPUT-2

< >

INPUT

The input signal type (ANALOG/DIGITAL) is

displayed within angle brackets < >.

When using a 2-input cable

Select [INPUT-1]

INPUT 2-A

INPUT 2-D

INPUT-1

INPUT

Note:

- When there is no input signal, [NO SIGNAL] is

displayed.

Connecting the monitor and turning the monitor on and off

Select [INPUT-2]

(analog)

Select [INPUT-2]

(digital)

15

EnglishDeutschFrançaisItalianoEspañolEnglish

Turning the power off

1. Turn the computer off.

2. Press the monitor's POWER button.

The Power LED will disappear.

OFF

If the monitor will not be used for a long time, turn

off the main power switch of the monitor, and

remove the power plug from the outlet.

Press power button

Turn the computer

off

Connecting the monitor and turning the monitor on and off

16

Adjusting the screen display and speaker volume

For analog signal

1.First perform an automatic adjustment. (p. 18)

2.Perform manual adjustment where necessary.

(p. 19)

For digital signal

The monitor can generally be used without

adjustment. If necessary perform manual

adjustment. (p. 23)

Note:

- All adjustments will be saved even after turning

the power off.

Adjustment value reset

Resetting all adjustment values

All adjustment values can be returned to their

original ex-factory values in one command.

1. Turn off the monitor power.

2. Press the MENU button and the button

simultaneously, and while doing this press the

power button (i.e. turn the power on). When [ALL

RESET] appears on the screen, the reset is

complete.

Notes:

- While ALL RESET is displayed, the control

buttons are disabled.

- It is not possible to reset values when the

adjustment lock is in place. Remove the

adjustment lock before attempting to operate

control buttons.

ADJUSTMENT menu reset

The adjustment values of the analog signal time’s

ADJUSTMENT menu can be returned to their

original ex-factory values.

1. Turn on the monitor power.

2. Press the MENU button and the

button

simultaneously. When [RESET] appears on the

screen, the reset is complete.

Adjustment lock function

By disabling the control buttons (i.e. setting the

lock) any attempted changes to adjusted values will

be voided.

1. Turn off the monitor power.

2.While pressing the MENU button, press the

power button (i.e. turn the power on).

Continue to press the button until [

ADJUSTMENT

LOCKED

] appears on the screen.The lock is set

when the message is displayed.

Note:

- When the lock is in place, all buttons other than

the power button are disabled.

Adjustment lock release

1. Turn off the monitor power.

2.While pressing the MENU button, press the

power button (i.e. turn the power on).

Continue to press the button until [

ADJUSTMENT

UNLOCKED

] appears on the screen.The lock is

released when the message is displayed.

Adjusting the backlight

Carry out the commands without the On Screen

Display (OSD) Menu displayed. If the OSD Menu is

displayed, press the MENU button (several times

may be required) and begin when the OSD Menu

has disappeared.

1. Without the OSD Menu being displayed, push the

or the button.

VOLUME 11

BRIGHT 31

2.Select [BRIGHT] by pressing the button.

3. Adjust by pressing the

button (darker) or

button (lighter).

Note:

- On Screen display for adjustment disappears

several seconds after the last operation.

17

EnglishDeutschFrançaisItalianoEspañolEnglish

Adjusting the speaker volume

Carry out the commands without the On Screen

Display (OSD) Menu displayed. If the OSD Menu is

displayed, press the MENU button (several times

may be required) and begin when the OSD Menu

has disappeared.

1. Without the OSD Menu being displayed, push the

or the button.

VOLUME 11

BRIGHT 31

2.Select [VLOUME] by pressing the button.

3. Adjust by pressing the

button (decrease) or

button (increase).

Note:

- On Screen display for adjustment disappears

several seconds after the last operation.

Checking product information

A model name (MODEL), a serial no. (S/N), and

usage time (USAGE TIME) of the display can be

checked.

1.Turn the power off.

2.While pressing the button, press the monitor's

power button (i.e. turn the power on).

3.Checking done: MENU button

Note:

- Please note that the indication of usage time at

purchase may not be 0 (zero), as a result of

factory inspection and other activities during

manufacture.

Adjusting the screen display and speaker volume

18

Adjusting the screen display (With analog connection)

Automatic screen adjustment

Options in the ADJUSTMENT Menu can be

adjusted automatically (CLOCK, PHASE, H-POS,

V-POS).

Note:

- When setting up this monitor for the first time or

after having changed an aspect of the current

system, perform an automatic screen adjustment

before use.

On Screen Display for the automatic adjust-

ment

First display an image that makes the entire screen

light.

If you are using Windows, you can use the Adjust-

ment Pattern on the accompanying CD-ROM.

Opening the Adjustment Pattern (for Windows)

This explanation is for Windows 95/98/2000/Me/XP,

and assumes that the CD-ROM drive is "D drive".

1.Load the accessory CD-ROM into the CD-ROM

drive of the computer.

2.Open [My Computer] and select CD-ROM. If

using Windows 3.1, open [File Manager] and

choose "D drive".

3.Double click on [Adj_uty.exe] to run the

Adjustment Program. The Adjustment Pattern will

appear.

Adjustment pattern

After completing the adjustments, press the

computer’s [Esc] key to exit the Adjustment

Program.

Note:

- If your computer’s display mode is set to 65K

colors, you may see the different color levels in

each color pattern or the gray scale may look

colored. (This is due to the specification of the

input signal and is not a malfunction.)

How to Adjust

1. Press the MENU button.

The ADJUSTMENT Menu will be displayed.

ADJUSTMENT

MANUAL AUTO

CLOCK 127

PHASE 16

H-POS 149

V-POS 31

INPUT-1 ANALOG

1280 x 1024 V : 60Hz H : 64kHz

2. Press the button.

The screen will become dark and [ADJUSTING]

will be displayed. After a few seconds the

ADJUSTMENT Menu will return. (The automatic

adjustment is now complete.)

3. Press the MENU button 5 times to make the

OSD Menu disappear.

Notes:

- In most cases automatic adjustment is

sufficient.

- If necessary due to any of the following, manual

adjustments (p. 19) can be performed after the

automatic adjustment.

- When further fine adjustment is needed.

- When the computer’s video input signals

are Composite Sync or Sync On Green.

(Automatic adjustments may not be

possible.)

- When [OUT OF ADJUST] is displayed.

(When the screen displays an entirely dark

image, the automatic screen adjustment

may be disabled. When making an

automatic adjustment, be sure to either use

the Adjustment Pattern or try displaying an

image that makes the entire screen very

bright.)

19

EnglishDeutschFrançaisItalianoEspañolEnglish

Manual screen adjustment

Adjustments can be made using On Screen

Display (OSD) Menu provided.

On Screen Display for adjustment

If you are using Windows, open the Adjustment

Pattern on the accompanying CD-ROM. (p. 18)

If your system is not Windows, you can not use the

Adjustment Pattern. Therefore display an image

that makes the entire screen light and adjust it

through checking visually its actual tone.

This chapter provides the procedure how to adjust

the screen by using Adjustment Pattern (for

Windows)

How to adjust

1.Press the MENU button.

The ADJUSTMENT Menu will be displayed.

ADJUSTMENT

MANUAL AUTO

CLOCK 127

PHASE 16

H-POS 149

V-POS 31

INPUT-1 ANALOG

1280 x 1024 V : 60Hz H : 64kHz

2.Select item to be adjusted by pressing the MENU

button.

Each time the MENU button is pressed the next

menu is selected. (ADJUSTMENT → GAIN

CONTROL → COLOR CONTROL → MODE

SELECT-1 → MODE SELECT-2 → OSD Menu

disappears)

Note:

- The OSD Menu automatically disappears

approximately 30 seconds after the last

command.

ADJUSTMENT Menu

ADJUSTMENT

MANUAL AUTO

CLOCK 127

PHASE 16

H-POS 149

V-POS 31

INPUT-1 ANALOG

1280 x 1024 V : 60Hz H : 64kHz

MANUAL: Individual menu options are manually

adjusted.

AUTO: Every menu option is automatically

adjusted.

Notes:

- Press the

button to select [AUTO].

- To choose a menu option: button

- To go to the next menu: MENU button

CLOCK

The figure below demonstrates how to adjust so

that vertical flicker noise is not emitted. (

buttons)

PHASE

The figure below demonstrates how to adjust so

that horizontal flicker noise is not emitted. (

buttons)

Note:

- Adjustments to PHASE should be made only

after CLOCK has been correctly set.

H-POS (horizontal positioning) and V-POS

(vertical positioning)

To center the screen image within the boundaries

of the screen, adjust the left-right (H-POS) values

and the up-down (V-POS) values. (

buttons)

Vertical flicker noise

Horizontal flicker noise

Screen frame

Adjusting the screen display (With analog connection)

20

Adjusting the screen display (With analog connection)

GAIN CONTROL Menu

GAIN CONTROL

MANUAL AUTO

BLACK LEVEL 88

CONTRAST 73

INPUT-1 ANALOG

1280 x 1024 V : 60Hz H : 64kHz

MANUAL: Individual menu options are manually

adjusted.

AUTO: Every menu option is automatically

adjusted using the Auto Gain Control*

function.

Notes:

- Press the

button to select [AUTO].

- To choose a menu option: button

- To go to the next menu: MENU button

* Auto Gain Control function

- The Auto Gain Control adjusts contrast and black

level based on the brightest color of the image

displayed. If you are not using the Adjustment

Pattern it is necessary to have an area of 5 mm x

5 mm of white displayed, and if not adjustments

may not be possible. (In such case, [OUT OF

ADJUST] will appear and setting values remain

unchanged.)

- If the signal coming from the computer is

composite sync or sync on green, automatic

adjustment cannot be performed. Please perform

manual adjustment instead.

BLACK LEVEL

Total screen brightness can be adjusted while

watching the color pattern. (

buttons)

CONTRAST

While watching the color pattern, adjustments can

be made so that all graduations appear. (

buttons)

Color pattern

COLOR CONTROL Menu

COLOR CONTROL

COLOR MODE sRGB STD VIVID

WHITE BALANCE

GAMMA

INPUT-1 ANALOG

1280 x 1024 V : 60Hz H : 64kHz

Notes:

- To choose a menu option: button

- To go to the next menu: MENU button

COLOR MODE

Color tone can be set as below.

STD ......... Displays image with the color tone

results from original scheme of liquid

crystal panel.

sRGB ....... sRGB is international standard of

color representation specified by IEC

(International Electrotechnical

Commission). Color conversion is

made in taking account of liquid

crystal’s characteristics and repre-

sents color tone close to it original

image.

VIVID ....... Displays an image with dynamic and

VIVID primary colors.

Subsequent items can be set when the [COLOR

MODE] is [STD].

WHITE BALANCE

After selecting [WHITE BALANCE], press the

button and display the adjustment menu.

WHITE BALANCE

COOL STD WARM USER

R-CONTRAST

G-CONTRAST

B-CONTRAST

OK <MENU>

Notes:

- On settings other than [STD] not all graduations

can be displayed. To display all graduations, set

to [STD].

- Use the

buttons to select [COOL], [·], [STD],

[·], [WARM] or [USER].

- Selecting USER will display the setting values for

[R-CONTRAST], [G-CONTRAST] and [B-

CONTRAST], in order to make fine adjustments.

- Use the button to select

[R-CONTRAST], [G-CONTRAST] and

[B-CONTRAST].

- When adjustment complete: MENU button

La page charge ...

Sharp Computer Monitor LL-T1815 Manuel utilisateur

Ce manuel convient également à

Sharp Computer Monitor LL-T1815 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents