Amana MED6200KW Manuel utilisateur

Marque: Amana

Modèle: MED6200KW

Catégorie: Sèche-linge électriques

Taper: Manuel utilisateur

Ce manuel convient également à

Electric Dryer [W11364660A, W11364661A-SP]

ELECTRIC DRYER OWNER’S MANUAL

GUIDE D’UTILISATION DE LA SÉCHEUSE ÉLECTRIQUE

Table of Contents

Dryer Safety

...........................................................2

Dryer Safety

.......................................................2

Dryer Maintenance and Care

..................................5

Cleaning the Dryer Location

................................5

Cleaning the Dryer Interior

..................................5

Removing Accumulated Lint

................................5

Cleaning the Lint Screen.....................................5

Changing the Drum Light (on some models) .........6

Check Your Vent System for Good Airflow

............6

Maintain Good Airflow

.........................................6

Nonuse, Storage, and Moving Care

.....................6

Special Instructions for Steam Models

.................7

Installation Instructions

..........................................7

Requirements................................................... ......7

Tools and Parts

..................................................7

Location Requirements.......................................8

Electrical Requirements – U.S.A..........................9

Electric Requirements – Canada ....................... 10

Installation

........................................................... 11

Install Leveling Legs

......................................... 11

Electrical Installation – U.S.A.

............................ 11

Venting Requirements

...................................... 17

Plan Vent System

............................................. 17

Install Vent System........................................... 19

Connect Inlet Hoses ......................................... 19

Connect Vent (Vented Models Only)

.................. 20

Level Dryer ...................................................... 21

Complete Installation Checklist.... ...................... 21

Sécurité de la sécheuse ....................................... 22

Sécurité de la sécheuse

.................................... 22

Entretien et réparation de la sécheuse ................. 25

Nettoyage de l’emplacement de la

sécheuse

......................................................... 25

Nettoyage de l’intérieur de la sécheuse.............. 25

Retrait de la charpie accumulée ........................ 25

Nettoyage du filtre à charpie.............................. 25

Changement de l’ampoule d’éclairage du

tambour (sur certains modèles)

......................... 26

Vérification d’une circulation d’air adéquate

pour le système d’évacuation

............................ 26

Pour maintenir une bonne circulation d’air .......... 26

Précautions à prendre lorsque l’appareil

n’est pas utilisé, est entreposé ou

déménagé

....................................................... 27

Instructions spécifiques pour les modèles

vapeur

............................................................. 27

Instructions d’installation

..................................... 28

Spécifications

...................................................... 28

Outils et pièces ................................................ 28

Exigences d’emplacement ................................ 29

Spécifications électriques – É.-U. ...................... 30

Spécifications électriques – Canada .................. 31

L’installation

......................................................... 32

Installation des pieds de nivellement.................. 32

Installation Électrique - U.S.A............................ 32

Exigences concernant l'évacuation

.................... 38

Planification des circuits de conduits

.................. 39

Installation du conduit d’évacuation

................... 41

Raccordement des tuyaux d’alimentation

........... 41

Raccorder le conduit d’évacuation (sur les

modèles avec conduit seulement)

...................... 42

Réglage de l’aplomb de la sécheuse.................. 43

Liste de vérification pour installation

terminée

.......................................................... 43

W11364660A

W11364661A-SP

Table des matières

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These

words mean:

DANGER

You can be killed or seriously injured if you don't

immediately follow instructions.

WARNING

You can be killed or seriously injured if you don’t follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

WARNING — “Risk of Fire”

− Clothes dryer installation must be performed by a qualified installer.

− Install the clothes dryer according to the manufacturer's instructions and local codes.

− Do not install a clothes dryer with flexible plastic venting materials or flexible metal (foil

type) duct. If flexible metal duct is installed, it must be of a specific type identified by the

appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials

are known to collapse, be easily crushed, and trap lint. These conditions will obstruct

clothes dryer airflow and increase the risk of fire.

− To reduce the risk of severe injury or death, follow all installation instructions.

− Save these instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions,

including the following:

n Read all instructions before using the appliance.

n Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-cleaning

solvents, or other flammable or explosive substances, as

they give off vapors that could ignite or explode.

n Do not allow children to play on or in the appliance. Close

supervision of children is necessary when the appliance is

used near children.

n Before the appliance is removed from service or discarded,

remove the door to the drying compartment.

n Do not reach into the appliance if the drum is moving.

n Do not install or store this appliance where it will be

exposed to the weather.

n Do not tamper with controls.

n Do not repair or replace any part of the appliance or attempt

any servicing unless specifically recommended in the user-

maintenance instructions or in published user-repair

instructions that you understand and have the skills to carry

out.

n Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

n Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

n Clean lint screen before or after each load.

n Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

n The interior of the appliance and exhaust duct should be

cleaned periodically by qualified service personnel.

n Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch fire. To

reduce the risk of fire due to contaminated loads, the final

part of a tumble dryer cycle occurs without heat (cool down

period). Avoid stopping a tumble dryer before the end of the

drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated.

n Do not use replacement parts that have not been

recommended by the manufacturer (e.g. parts made at

home using a 3D printer).

n See the Installation Instructions for grounding requirements

and installation.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

WHEN DISCARDING OR STORING YOUR OLD CLOTHES DRYER, REMOVE THE DOOR.

SAVE THESE INSTRUCTIONS

Internet Connectivity Guide for Connected Appliances Only

IMPORTANT: Proper installation of your appliance prior to use is your responsibility. Be sure to read and follow the installation

instructions that came with your appliance.

Connectivity requires Wi-Fi and account creation. App features and functionality are subject to change. Data rates may apply. Once

installed, launch the app. You will be guided through the steps to set up a user account and to connect your appliance.

You Will Need:

n A home wireless router supporting Wi-Fi, 2.4Ghz with WPA2 security. If you are unsure of your router’s capabilities, refer to the router

manufacturer’s instructions.

n The router to be on and have a live internet connection.

n The 10–character SAID code for your appliance. The SAID code is either printed on a label on the appliance or found on the LCD

screen.

Federal Communications Commission (FCC) Compliance Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

Industry Canada (IC) Compliance Notice

This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain

approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain

should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful

communication.

To comply with FCC and Industry Canada RF radiation exposure limits for general population, antenna(s) used for this transmitter must

be installed such that a minimum separation distance of 20 cm is maintained between the radiator (antenna) and all persons at all times

and must not be co-located or operating in conjunction with any other antenna or transmitter.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one of the following measures:

n Reorient or relocate the receiving antenna.

n Increase the separation between the equipment and receiver.

n Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

n Consult the dealer or an experienced radio/TV technician for help.

DRYER MAINTENANCE AND

CARE

Cleaning the Dryer Location

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline,

away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Place dryer at least 18 inches (460 mm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

Keep dryer area clear and free from items that would block the

airflow for proper dryer operation. This includes clearing piles of

laundry in front of the dryer.

Cleaning the Dryer Interior

To clean dryer drum:

1. Use nonflammable cleaner or a mild hand dish detergent

mixed at a low concentration with very warm water, and rub

with a soft cloth.

n Rinse well with a wet sponge or towel.

n Tumble a load of clean clothes or towels to dry drum.

2. Use a microfiber cloth and hot water in a spray bottle to clean

the drum and a second microfiber towel to dry.

NOTE: Garments that contain unstable dyes, such as denim blue

jeans or brightly colored cotton items, may discolor the rear of the

dryer interior. These stains are not harmful to your dryer and will

not stain future loads of clothes. Dry unstable dye items inside out

to avoid transfer of dye.

Removing Accumulated Lint

From inside the dryer cabinet:

Lint should be removed every 2 years, or more often, depending

on dryer usage. Cleaning should be done by a qualified appliance

service or ventilation system cleaner.

From the exhaust vent:

Lint should be removed every 2 years, or more often, depending

on dryer usage.

Cleaning the Lint Screen

Every load cleaning:

The lint screen may be located either in the door opening or the

top of the dryer depending on model. A screen blocked by lint can

increase drying time.

To clean:

1. Remove the lint screen. If necessary, press the tab to release

and open the lint screen. Roll lint off the screen with your

fingers. Do not rinse or wash screen to remove lint. Wet lint is

hard to remove.

2. Push the lint screen firmly back into place.

IMPORTANT:

n Do not run the dryer with the lint screen loose, damaged,

blocked, or missing. Doing so can cause overheating and

damage to both the dryer and fabrics.

n If lint falls off the screen into the dryer during removal, check

the exhaust hood and remove the lint. See “Venting

Requirements” in the Installation Instructions.

n Clean space where lint screen is located, as needed. Using a

vacuum, gently remove any lint that has accumulated outside

of the lint screen.

As-needed cleaning:

Laundry detergent and fabric softener residue can build up on the

lint screen. This buildup can cause longer drying times for your

clothes, or cause the dryer to stop before your load is completely

dry. The screen is probably clogged if lint falls off while the screen

is in the dryer. Clean the lint screen with a nylon brush every 6

months, or more frequently, if it becomes clogged due to a residue

buildup.

To wash:

1. Roll lint off the screen with your fingers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent. Scrub

lint screen with the brush to remove residue buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel. Reinstall screen

in dryer.

Changing the Drum Light (on some

models)

1. Unplug dryer or disconnect power.

2. Open the dryer door. Locate the light bulb cover on the back

wall of the dryer. Using a Phillips-head screwdriver or 1/4"

(6.35 mm) nut driver or socket wrench, remove the screw

located in the lower right-hand corner of the cover. Remove

the cover.

3. Turn bulb counterclockwise. Replace the bulb with a 10 W

appliance bulb only. Replace the cover and secure with the

screw.

4. Plug in dryer or reconnect power.

Accessories and replacement parts are available for your model.

For ordering and contact information, please reference your Quick

Start Guide.

Check Your Vent System for Good

Airflow

WARNING

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death or

fire.

Good Airflow

Along with heat, dryers require good airflow to efficiently dry

laundry. Proper venting will reduce your drying times and improve

your energy savings. See Installation Instructions.

The venting system attached to the dryer plays a big role in good

airflow. Blocked or crushed vents as well as improper venting

installation will reduce air flow and dryer performance.

Service calls caused by improper venting are not covered by the

warranty and will be paid by the customer, regardless of who

installed the dryer. To clean or repair venting, contact a venting

specialist.

Maintain Good Airflow

n Cleaning your lint screen before each load.

n Replace plastic or foil vent material with 4" (102 mm) diameter

heavy, rigid vent material.

n Use the shortest length of vent possible.

n Use no more than four 90° elbows in a vent system; each bend

and curve reduces airflow.

n Remove lint and debris from the exhaust hood.

n Remove lint from the entire length of the vent system at least

every 2 years. When cleaning is complete, be sure to follow

the Installation Instructions for final product check.

n Clear away items from the front of the dryer.

Nonuse, Storage, and Moving Care

Nonuse or Storage Care

If you will be on vacation or not using your dryer for an extended

period of time, you should:

1. Unplug dryer or disconnect power.

2. Clean lint screen. See “Cleaning the Lint Screen.”

3. Turn off the water supply to the dryer. This helps to avoid

unintended flooding (due to a water pressure surge) while you

are away.

Moving Care

For power supply cord-connected dryers:

1. Unplug the power supply cord.

2. Steam models only: Shut off water faucet. Disconnect the

water inlet hose from faucet; then drain the hose. Transport

hose separately.

3. Make sure leveling legs are secure in dryer base.

4. Use tape to secure dryer door.

For direct-wired dryers:

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1. Turn off power at fuse or breaker box.

2. Disconnect wiring.

3. Steam models only: Shut off water faucet.

4. Steam models only: Disconnect the water inlet hose from

faucet; then drain the hose. Transport hose separately.

5. Make sure leveling legs are secure in dryer base.

6. Use tape to secure dryer door.

Special Instructions for Steam

Models

Install and store your dryer where it will not freeze. Because some

water may stay in the hose, freezing can damage your dryer. If

storing or moving your dryer during freezing weather, winterize it.

Water inlet hose

Replace inlet hose and hose screen after 5 years of use to reduce

the risk of hose failure. Periodically inspect and replace inlet hose

if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hose, record the date of replacement.

To winterize the dryer:

1. Unplug dryer or disconnect power.

2. Shut off water faucet.

3. Disconnect water inlet hose from faucet and drain.

To use the dryer again:

1. Flush water pipes. Reconnect water inlet hose to faucet. Turn

on water faucet.

2. Plug in dryer or reconnect power as described in the

Installation Instructions.

Reinstalling the Dryer

Follow the Installation Instructions to locate, level, and connect the

dryer.

INSTALLATION INSTRUCTIONS

REQUIREMENTS

Tools and Parts

NOTE: Install the clothes dryer according to the manufacturer’s

instructions and local codes.

Gather required tools and parts before starting installation. Read

and follow the instructions provided with any tools listed here.

Tools Needed for All Installations:

Flat-blade screwdriver

#2 Phillips screwdriver

1/4” Nut driver

Level

Pliers

Tape measure

Utility knife

Tin snips

Caulking gun and compound

Adjustable wrench that opens

to 1” (25 mm) or hex-head

socket wrench

Wire stripper

Additional Tools Needed (on some models):

Putty knife

Parts Supplied (all models):

Leveling legs (4) (Length and appearance of legs may vary

according to model)

Parts package is located in dryer drum. Check that all parts are

included.

NOTE: Do not use leveling legs supplied with dryer if installing

with a pedestal or stack kit.

Parts Needed (steam models):

“Y” connector

2' (0.6 m) inlet hose

Rubber washer

5' (1.52 m) inlet hose

Vented Models:

Vent Clamps, elbows, and vent work

Parts Needed (all models):

Additional parts may be required, depending on your installation.

Check local codes. Check existing electrical supply and venting.

Read “Electrical Requirements” and “Venting Requirements”

before purchasing parts.

Mobile home installations require metal exhaust system hardware

available for purchase from the dealer from whom you purchased

your dryer. For further information, please refer to the Quick Start

Guide for service contact information.

Available Accessories:

Refer to your Quick Start Guide for contact and ordering

information.

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline,

away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Place dryer at least 18 inches (460 mm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

Check code requirements. Some codes limit, or do not permit,

installing dryer in garages, closets, mobile homes, or sleeping

quarters. Contact your local building inspector.

You will need:

n For vented models: A location allowing for proper exhaust

installation. See “Venting Requirements.”

n A separate 30 A circuit for electric dryers.

n If you are using power supply cord, a grounded electrical outlet

located within 2 ft. (610 mm) of either side of dryer. See

“Electrical Requirements.”

n A sturdy floor to support dryer weight of 200 lbs. (90.7 kg).

Also, consider the combined weight of the companion

appliance.

n For steam dryers: Cold water faucets located within 4 ft. (1.2

m) of the water fill valves, and water pressure of 20–120 psi

(138–827 kPa). You may use the water supply for your washer

using the necessary parts as noted (which you may need to

purchase).

n Level floor with a maximum slope of 1" (25 mm) under the

entire dryer. If the slope is greater than 1" (25 mm), install

Extended Dryer Feet Kit. If not level, clothes may not tumble

properly and automatic sensor cycles may not operate

correctly.

n For garage installation, place dryer at least 18" (460 mm)

above the floor. If using a pedestal, you will need 18" (460 mm)

to bottom of the dryer.

n The dryer must not be installed or stored in an area where it

will be exposed to water and/or weather.

IMPORTANT: Do not operate dryer at temperatures below 45°F

(7°C). Lower temperatures may cause dryer not to shut off at end

of automatic sensor cycles, resulting in longer drying times.

Installation clearances:

For each arrangement, consider allowing more space for ease of

installation and servicing, spacing for companion appliances, and

clearances for walls, doors, and floor moldings. Space must be

large enough to allow the dryer door to fully open. Add spacing on

all sides of the dryer to reduce noise transfer. If a closet door or

louvered door is installed, top and bottom air openings in the door

are required.

Installation spacing for a recessed area or closet installation

All dimensions show recommended and minimum spacing

allowed.

n Additional spacing should be considered for ease of

installation and servicing.

n Additional clearances might be required for wall, door, floor,

moldings, dryer venting, and drain system.

n Additional spacing should be considered on all sides of the

dryer to reduce noise transfer.

n For closet installation with a door, minimum ventilation

openings in the top and bottom of the door are required for

vented models. Louvered doors with equivalent ventilation

openings are acceptable.

n Companion appliance spacing should also be considered.

Recommended installation clearances (dryer

only):

*Additional spacing recommended.

Minimum installation clearances (dryer only):

Front Sides Rear Top

Recessed NA 0" (0 mm) 0" (0 mm) 0" (0 mm)

Closet NA 0" (0 mm) 0" (0 mm) 0" (0 mm)

Under

Counter

NA 1" (25 mm) 0" (0 mm) 0" (0 mm)

0" (0 mm) rear spacing is allowed for straight-back venting only.

For steam models only, inlet hose must not be kinked.

Mobile Home – Additional installation

requirements

This dryer is suitable for mobile home installations. The

installation must conform to the Manufactured Home Construction

and Safety Standard, Title 24 CFR, Part 3280 (formerly the

Federal Standard for Mobile Home Construction and Safety, Title

24, HUD Part 280) or the Standard for Mobile Homes, CAN/CSA-

Z240 MH.

Mobile home installations require:

n Metal exhaust system hardware, which is available for

purchase from your dealer.

n Special provisions must be made in mobile homes to introduce

outside air into the dryer. The opening (such as a nearby

window) should be at least twice as large as the dryer exhaust

opening.

Electrical Requirements – U.S.A.

It is your responsibility:

n To contact a qualified electrical installer.

n To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/ NFPA

70 – latest edition and all local codes and ordinances. The

National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved in

remodeling after 1996, and all mobile home installations. A

copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02169–7471.

n To supply the required 3- or 4-wire, single-phase, 120/240 V,

60 Hz, AC-only electrical supply (or 3- or 4-wire, 120/208 V

electrical supply, if specified on the serial/rating plate) on a

separate 30 A circuit, fused on both sides of the line. Connect

to an individual branch circuit. Do not have a fuse in the neutral

or grounding circuit.

n Do not use an extension cord.

n If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

n This dryer is manufactured ready to install with a 3-wire

electrical supply connection. The neutral ground conductor is

permanently connected to the neutral conductor (white wire)

within the dryer. If the dryer is installed with a 4-wire electrical

supply connection, the neutral ground conductor must be

removed from the external ground connector (green screw),

and secured under the neutral terminal (center or white wire)

of the terminal block. When the neutral ground conductor is

secured under the neutral terminal (center or white wire) of the

terminal block, the dryer cabinet is isolated from the neutral

conductor. The green ground wire of the 4-wire power cord

must be secured to the dryer cabinet with the green ground

screw

n If local codes do not permit the connection of a neutral ground

wire to the neutral wire, see “Optional 3-Wire Connection.”

n A 4-wire power supply connection must be used when the

appliance is installed in a location where grounding through

the neutral conductor is prohibited. Grounding through the

neutral conductor is prohibited for (1) new branch-circuit

installations after 1996, (2) mobile homes, (3) recreational

vehicles, and (4) areas where local codes prohibit grounding

through the neutral conductors.

If using a power supply cord:

Use a UL-listed power supply cord kit marked for use with clothes

dryers. The kit should contain:

n A UL-listed 30 A power supply cord, rated 120/240 V

minimum. The cord should be type SRD or SRDT and be at

least 4 ft. (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or spade terminals with upturned

ends.

n A UL-listed strain relief.

If your outlet looks like this:

4-wire receptacle

(14-30R)

Then choose a 4-wire power supply cord

with ring or spade terminals and UL-listed

strain relief. The 4-wire power supply cord,

at least 4 ft. (1.22 m) long, must have four

10-gauge copper wires and match a 4-wire

receptacle of NEMA Type 14-30 R. The

ground wire (ground conductor) may be

either green or bare. The neutral

conductor must be identified by a white

cover.

If your outlet looks like this:

3-wire receptacle

(10-30R)

Then choose a 3-wire power supply cord

with ring or spade terminals and UL-listed

strain relief. The 3-wire power supply cord,

at least 4 ft. (1.22 m) long, must have three

10-gauge copper wires and match a 3-wire

receptacle of NEMA Type 10-30R.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

 Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), covered with flexible metallic conduit. All

current-carrying wires must be insulated.

 10-gauge solid copper wire (do not use aluminum) at least 5 ft.

(1.52 m) long.

GROUNDING INSTRUCTIONS

For a grounded, cord-connected appliance:

This appliance must be grounded. In the event of a

malfunction or breakdown, grounding will reduce the risk of

electric shock by providing a path of least resistance for

electric current. This appliance is equipped with a cord having

an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local

codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative if

you are in doubt as to whether the appliance is properly

grounded. Do not modify the plug provided with the

appliance: If it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

For a permanently connected appliance:

This appliance must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the appliance.

SAVE THESE INSTRUCTIONS

Electric Requirements – Canada

WARNING

Electrical Shock Hazard

Plug into a grounded 4 prong outlet.

Failure to do so can result in death or electrical shock.

It is your responsibility:

 To contact a qualified electrical installer.

 To be sure that the electrical connection is adequate and in

conformance with Canadian Electrical Code, C22.1 – latest

edition and all local codes. A copy of above codes standard

may be obtained from: Canadian Standards Association, 178

Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

 To supply the required 4-wire, single-phase, 120/240 V, 60 Hz,

AC-only electrical supply on a separate 30 A circuit, fused on

both sides of the line. A time-delay fuse or circuit breaker is

recommended. Connect to an individual branch circuit.

 This dryer is equipped with a UL-listed and/or CSA

International Certified Power Cord intended to be plugged into

a standard 14-30R wall receptacle. The cord is 5 ft. (1.52 m)

long. Be sure wall receptacle is within reach of dryer’s final

location.

4-wire receptacle (14-30R)

 If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

 Do not use an extension cord.

For further information, or to obtain a Power Supply Cord

Replacement (Part Number W11095079), please reference the

contact information listed on your Quick Start Guide.

GROUNDING INSTRUCTIONS

For a grounded, cord-connected appliance:

This appliance must be grounded. In the event of a

malfunction or breakdown, grounding will reduce the risk of

electric shock by providing a path of least resistance for

electric current. This appliance is equipped with a cord having

an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local

codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative if

you are in doubt as to whether the appliance is properly

grounded. Do not modify the plug provided with the

appliance: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

INSTALLATION

Install Leveling Legs

WARNING

Excessive Weight Hazard

Use two or more people to move and install or uninstall

appliance.

Failure to do so can result in back or other injury.

1. Prepare dryer for leveling legs

To avoid damaging floor, use a large flat piece of cardboard

from dryer carton; place under entire back edge of dryer.

Firmly grasp dryer body (not console panel) and gently lay

dryer down on cardboard.

NOTE: Residual water from factory testing may drain when

dryer is laying on its side.

2. Screw in leveling legs

Leveling leg with diamond

marking.

Leveling leg without diamond

marking

Using a wrench and tape measure, screw leveling legs into

leg holes until bottom of foot is approximately 1/2" (13 mm) to

1 1/2" (38 mm) from bottom of the dryer.

For leveling legs with the diamond marking:

Screw legs into leg holes by hand. Use a wrench to finish

turning legs until diamond marking is no longer visible.

Place a carton corner post from dryer packaging under each

of the two dryer back corners. Stand the dryer up. Slide the

dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent.

Electrical Installation – U.S.A.

WARNING

Fire Hazard

For power supply cord, use a new UL listed 30 A power

supply cord.

For direct wire, use 10 gauge copper wire.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal (silver).

Connect ground wire (green or bare wire) to green

ground connector.

Connect remaining 2 supply wires to remaining 2

terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or electrical

shock.

1. Disconnect power

2. Remove terminal block cover

Remove hold-down screw and terminal block cover.

3. Choose electrical connection type

Power supply cord 4-wire receptacle

(NEMA Type 14-30R): Go to “4-Wire Power

Supply Cord Connection.” Then, go to

“Venting Requirements.”

Power supply cord 3-wire receptacle

(NEMA Type 10-30R): Go to “3-Wire Power

Supply Cord Connection.” Then, go to

“Venting Requirements.”

4-wire direct connection: Go to “Direct Wire

Strain Relief,” then “4-Wire Direct Wire

Connection,” then, go to “Venting

Requirements.”

3-wire direct connection: Go to “Direct Wire

Strain Relief”, then “3-Wire Direct Wire

Connection,” then, go to “Venting

Requirements.”

NOTE: If local codes do not permit connection of a cabinet-

ground conductor to neutral wire, go to “Optional 3-wire

Connection.” This connection may be used with either a

power supply cord or a direct wire connection.

Power Supply Cord Connection

Power Supply Cord Strain Relief

1. Attach power supply cord strain relief

Remove the screws from a 3/4" (19 mm) UL-listed strain relief

(UL marking on strain relief). Put the tabs of the two clamp

sections (C) into the hole below the terminal block opening

(B) so that one tab is pointing up (A) and the other is pointing

down (D), and hold in place. Tighten strain relief screws just

enough to hold the two clamp sections (C) together.

2. Attach power supply cord to strain relief

Put power supply cord through the strain relief. Be sure that

the wire insulation on the power supply cord is inside the

strain relief. The strain relief should have a tight fit with the

dryer cabinet and be in a horizontal position. Do not further

tighten strain relief screws at this point.

4-Wire Power Supply Cord Connection

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire

connections.

A. 4-wire receptacle (NEMA type 14-30R)

B. 4-prong plug

C. Ground prong

D. Neutral prong

E. Spade terminals with upturned ends

F. 3/4" (19 mm) UL-listed strain relief

G. Ring terminals

3. Prepare to connect neutral ground wire and

neutral wire

Remove center terminal block screw (B). Remove neutral

ground wire (E) from green external ground conductor screw

(A).

4. Connect neutral ground wire and neutral wire

Connect neutral ground wire (E) and neutral wire (white or

center) (C) of power supply cord under center terminal block

screw (B). Tighten screw.

5. Connect ground wire

Connect ground wire (F) (green or bare) of power supply cord

under green external ground conductor screw (A). Tighten

screw.

6. Connect remaining wires

Connect remaining wires under outer terminal block screws.

Tighten screws. Insert tab of terminal block cover into slot of

dryer rear panel. Secure cover with hold-down screw. Now,

go to “Venting Requirements.”

3-Wire Power Supply Cord Connection

IMPORTANT: Use where local codes permit connecting cabinet-

ground conductor to neutral wire.

A. 3-wire receptacle (NEMA type 10-30R)

B. 3-wire plug

C. Neutral prong

D. Spade terminals with upturned ends

E. 3/4" (19 mm) UL-listed strain relief

F. Ring terminals

G. Neutral (white or center wire)

3. Remove center screw

Remove center terminal block screw (B).

4. Connect neutral wire

Connect neutral wire (white or center) (C) of power supply

cord under center terminal block screw (B). Tighten screw.

5. Connect remaining wires

Connect remaining wires under outer terminal block screws.

Tighten screws. Insert tab of terminal block cover into slot of

dryer rear panel. Secure cover with hold-down screw. Now,

go to “Venting Requirements.”

Direct Wire Connection

Direct wire strain relief

1. Attach direct wire strain relief

Unscrew the removable conduit connector (A) and any

screws from a 3/4" (19 mm) UL-listed strain relief (UL marking

on strain relief). Put the threaded section of the strain relief

through the hole below the terminal block opening (B).

Reaching inside the terminal block opening, screw the

removable conduit connector (A) onto the strain relief threads

2. Attach direct wire cable to strain relief

Put direct wire cable through the strain relief. The strain relief

should have a tight fit with the dryer cabinet and be in a

horizontal position. Tighten strain relief screw against the

direct wire cable.

For 4-wire Direct Wire Connection, continue to step 3.

4-wire direct wire connection: Go

to “4-Wire Direct Wire

Connection.”

For 3-wire Direct Wire Connection, continue to step 3.

3-wire direct wire connection: Go

to “3-Wire Direct Wire

Connection.”

4-Wire Direct Wire Connection

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit 3-wire connections.

3. Prepare your 4-wire cable for direct

connection

Direct wire cable must have 5 ft. (1.52 m) of extra length so

dryer may be moved if needed.

Strip 5" (127 mm) of outer covering from end of cable, leaving

bare ground wire at 5" (127 mm). Cut 1 1/2" (38 mm) from

remaining 3 wires. Strip insulation back 1" (25 mm). Shape

ends of wires into hooks.

4. Prepare to connect neutral ground wire and

neutral wire

Remove center terminal block screw (B). Remove neutral

ground wire (E) from green external ground conductor screw

(A).

5. Connect neutral ground wire and neutral wire

Connect neutral ground wire (E) and place hooked end (hook

facing right) of neutral wire (white or center wire) (C) of direct

wire cable under center screw of terminal block (B). Squeeze

hooked ends together and tighten screw.

6. Connect ground wire

Connect ground wire (green or bare) (F) of direct wire cable

under green external ground conductor screw (A). Tighten

screw.

7. Connect remaining wires

Place hooked ends of remaining direct wire cable wires under

outer terminal block screws (hooks facing right). Squeeze

hooked ends together and tighten screws. Insert tab of

terminal block cover into slot of dryer rear panel. Secure

cover with hold-down screw. Now, go to “Venting

Requirements.”

3-Wire Direct Wire Connection

IMPORTANT: Use where local codes permit connecting cabinet-

ground conductor to neutral wire.

3. Prepare your 3-wire cable for direct

connection

Direct wire cable must have 5 ft. (1.52 m) of extra length so

dryer may be moved if needed.

Strip 3 1/2" (89 mm) of outer covering from end of cable. Strip

insulation back 1" (25 mm). If using 3-wire cable with ground

wire, cut bare wire even with outer covering. Shape wire ends

into hooks.

4. Remove center screw

Remove center terminal block screw (B).

5. Connect neutral wire

Place hooked end of neutral wire (white or center) (C) of

direct wire cable under center terminal block screw (B).

Squeeze hooked end together. Tighten screw.

6. Connect remaining wires

Place hooked ends of remaining direct wire cable wires under

outer terminal block screws (hooks facing right). Squeeze

hooked ends together and tighten screws. Insert tab of

terminal block cover into slot of dryer rear panel. Secure

cover with hold-down screw. Now, go to “Venting

Requirements.”

Optional 3-Wire Connection (Power Supply Cord

Shown)

IMPORTANT: You must verify with a qualified electrician that this

grounding method is acceptable before connecting.

1. Prepare to connect neutral ground wire and

neutral wire

Install the correct strain relief for your electrical connection

method. Remove center terminal block screw (B). Remove

neutral ground wire (E) from green external ground conductor

screw (A).

2. Connect neutral ground wire and neutral wire

Connect neutral ground wire (E) and neutral wire (white or

center wire) (C) of power supply cord or cable under center

terminal block screw (B). Tighten screw.

3. Connect remaining wires

Place remaining wires under outer terminal block screws.

Tighten screws.

4. Connect external ground wire

Connect a separate copper ground wire (G) from the green

external ground conductor screw (A) to an adequate ground.

Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw. Now, go to “Venting

Requirements.”

Venting Requirements

WARNING

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death or

fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances. Dryer

exhaust must not be connected into any gas vent, chimney, wall,

ceiling, attic, crawlspace, or a concealed space of a building. Only

rigid or flexible metal vent shall be used for exhausting.

n Only a 4" (102 mm) heavy metal exhaust vent and clamps may

be used.

n Do not use plastic or metal foil vent.

Rigid metal vent:

n Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent (acceptable only if accessible to clean):

n Must be fully extended and supported in final dryer location.

n Remove excess to avoid sagging and kinking that may result

in reduced airflow and poor performance.

n Do not install in enclosed walls, ceilings, or floors.

n The total length should not exceed 7 3/4 ft. (2.4 m).

n The length of flexible metal vent used must be included in the

overall vent system design as shown in the “Vent System

Chart.”

NOTE: If using an existing vent system, clean lint from entire

length of the system and make sure exhaust hood is not plugged

with lint. Replace plastic or metal foil vents with rigid metal or

flexible metal vents. Review “Vent System Chart” and, if

necessary, modify existing vent system to achieve best drying

performance.

Exhaust hoods:

n An exhaust hood should cap the vent to keep rodents and

insects from entering the home.

n Must be at least 12" (305 mm) from ground or any object that

may obstruct exhaust (such as flowers, rocks, bushes, or

snow).

n Do not use an exhaust hood with a magnetic latch.

Recommended Styles: Acceptable Style:

Louvered Hood

Box Hood

Angled Hood

Elbows:

n 45° elbows provide better airflow than 90° elbows.

Clamps:

n Use clamps to seal all joints.

n Exhaust vent must not be connected or secured with screws or

other fastening devices that extend into interior of duct and

catch lint. Do not use duct tape.

Vent products can be purchased from your dealer. For contact and

ordering information, refer to your Quick Start Guide.

Plan Vent System

Recommended exhaust installations:

Typical installations vent the dryer from the rear of the dryer. Other

installations are possible.

A. Dryer

B. Elbow

C. Wall

D. Exhaust hood

E. Clamps

F. Rigid metal or flexible metal

vent

G. Vent length necessary to

connect elbows

H. Exhaust outlet

I. Optional side exhaust outlet

Optional exhaust installations:

WARNING

Fire Hazard

Cover unused exhaust holes with a manufacturer’s

exhaust cover kit.

Contact your local dealer.

Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

Some models can be converted to exhaust out the right side, left

side, or through the bottom. If you prefer, you may contact your

local dealer to have the dryer converted.

A. Standard rear offset exhaust installation

B. Left- or right-side exhaust installation (available only on

select 27"-wide models).

C. Bottom exhaust installation (available only on select 27"-

wide models).

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for

your installation. Two close-clearance installations are shown.

NOTE: The following kits for close-clearance alternate

installations are available for purchase. Refer to Quick Start Guide

for contact information.

Over-The-Top installation

(also available with one offset

elbow)

Periscope installation

Special provisions for mobile home installations:

Exhaust vent must be securely fastened to a noncombustible

portion of the mobile home and must not terminate beneath the

mobile home. Terminate exhaust vent outside.

Determine vent path:

n Select route that will provide

straightest and most direct path

outdoors.

n Plan installation to use fewest

number of elbows and turns.

n When using elbows or making

turns, allow as much room as

possible.

n Bend vent gradually to avoid

kinking.

n Use as few 90° turns as

possible.

Determine vent length and elbows needed for best

drying performance:

n Use following “Vent System Chart” to determine type of vent

material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in

“Vent System Chart.” Exhaust systems longer than those

specified will:

n Shorten life of dryer.

n Reduce performance, resulting in longer drying times and

increased energy usage.

The “Vent System Chart” provides venting requirements that will

help achieve best drying performance.

Vent System Chart

Number of 90°

turns or elbows

Type of vent

Box/louvered or

Angled hoods

Rigid metal 64 ft. (20 m)

Rigid metal 54 ft. (16.5 m)

Rigid metal 44 ft. (13.4 m)

Rigid metal 35 ft. (10.7 m)

Rigid metal 27 ft. (8.2 m)

NOTE: Side and bottom exhaust installations have a 90º turn

inside the dryer. To determine maximum exhaust length, add one

90º turn to the chart.

Vent System Chart (Long Vent Models)

Number of 90°

turns or elbows

Type of vent Box/louvered or

Angled hoods

0 Rigid metal 160 ft. (48.8 m)

1 Rigid metal 150 ft. (45.7 m)

2 Rigid metal 140 ft. (42.7 m)

3 Rigid metal 130 ft. (39.6 m)

4 Rigid metal 120 ft. (36.6 m)

5 Rigid metal 110 ft. (33.5 m)

To determine if your model has a long vent system, refer to the

type code located on the serial number plate in the inner door

well. Example: A Long Vent Model would be BJAV-NAT-

XXXXXXX-XXX or BWFB-NAT-XXXXXXX-XXX.

NOTE: For long vent systems, use of box/louvered hoods will

improve venting regardless of length.

Additional Elbows

In cases in which the Installation Instructions do not address the

vent length for the specific number of elbows required for a

particular application, the following calculations may be used.

(The total vent system length includes all straight and curved

portions of the vent system):

n For 90° elbows, reduce the allowable vent system length by

10 Ft. (3.05 m).

n For 45° elbows, reduce the allowable vent system length by

6 Ft. (1.83 m).

For example, if the Installation Instructions state that a dryer is

allowed 40 Ft. (12.2 m) of total vent length with two 90° bends, the

total allowable vent length would be reduced by 10 Ft. (3.0 m)

(from 40 Ft [12.2 m] to 30 Ft. [9.1m]).

Install Vent System

1. Install exhaust hood

Install exhaust hood and use caulking compound to seal

exterior wall opening around exhaust hood.

2. Connect vent to exhaust hood

Vent must fit over the exhaust hood. Secure vent to exhaust

hood with 4" (102 mm) clamp. Run vent to dryer location

using straightest path possible. Avoid 90° turns. Use clamps

to seal all joints. Do not use duct tape, screws, or other

fastening devices that extend into interior of vent to secure

vent, because they can catch lint.

Connect Inlet Hoses

For vented, non-steam models, skip to “Connect Vent.”

The dryer must be connected to the cold water faucet using the

new inlet hoses. Do not use old hoses.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Record hose installation or replacement dates on

the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts, wear,

or leaks are found.

1. Turn cold water off, remove and replace rubber

washer

Turn cold water faucet off and remove washer inlet hose.

Remove old rubber washer from inlet hose and replace with

new rubber washer.

2. Attach short hose and “Y” connector

Attach 2 ft. (0.6 m) inlet hose to cold water faucet. Screw on

coupling by hand until it is seated on faucet. Then attach “Y”

connector to male end of the 2 ft. (0.6 m) inlet hose. Screw on

coupling by hand until it is seated on connector.

3. Tighten couplings

Using pliers, tighten the couplings with additional two-thirds

turn.

NOTE: Do not overtighten. Damage to the coupling can

result.

4. Attach long hose to “Y” connector and tighten

couplings

Attach one of the 5 ft. (1.5 m) inlet hose ends to the “Y”

connector. Attach washer cold inlet hose to other side of “Y”

connector. Screw on coupling by hand until it is seated on

connector. Using pliers, tighten the couplings an additional

two-thirds turn.

NOTE: Do not overtighten. Damage to the coupling can

result.

5. Attach long hose to dryer fill valve and tighten

coupling

If applicable, remove protective cap from water inlet valve.

Attach other end of long hose to fill valve on dryer back panel.

Screw on coupling by hand until it is seated on fill valve

connector. Using pliers, tighten the couplings an additional

two-thirds turn.

NOTE: Do not overtighten. Damage to the coupling can

result.

6. Turn on cold water faucet

Check that the water faucet is turned on.

7. Check for leaks

Check for leaks around “Y” connector, faucets, and hoses.

Connect Vent (Vented Models Only)

1. Connect vent to exhaust outlet

Using a 4" (102 mm) clamp, connect vent to exhaust outlet in

dryer. If connecting to existing vent, make sure vent is clean.

Dryer vent must fit over dryer exhaust outlet and inside

exhaust hood. Check that vent is secured to exhaust hood

with a 4" (102 mm) clamp.

2. Move dryer to final location

Move dryer to final location. Avoid crushing or kinking the

vent.

After dryer is in place, remove corner posts and cardboard

from under dryer.

La page charge ...

Amana MED6200KW Manuel utilisateur

Marque: Amana

Modèle: MED6200KW

Catégorie: Sèche-linge électriques

Taper: Manuel utilisateur

Ce manuel convient également à

Electric Dryer [W11364660A, W11364661A-SP]

Télécharger le PDF

rapport

dans d''autres langues

English: Amana MED6200KW User manual

Amana MED6200KW Manuel utilisateur

Ce manuel convient également à

Amana MED6200KW Manuel utilisateur

dans d''autres langues

Autres documents