Forney 298 Manuel utilisateur

Marque: Forney

Modèle: 298

Catégorie: Système de soudage

Taper: Manuel utilisateur

Ce manuel convient également à

298 100 ST Easy Weld

WWW.FORNEYIND.COM

CAT# 298

REV 12.27.17

INCLUDES:

Welding Machine, Stick Electrode Holder

and Ground Cable and Clamp

100 ST STICK/TIG ARC

WELDER OPERATING MANUAL

ENGLISH

WWW.FORNEYIND.COM

Forney Promise

We are committed to your success regardless of location, size or

needs. We understand it is your goal to get the job done right,

and we are ready to help you do just that.

President's Message

We market the highest quality tools, equipment and accessories

for the do-it-yourselfer and professional. Our passion and

dedication in bringing new products to the industrial and retail

market, combined with our personal service, is unmatched in our

industry. Our ability to listen to our customers’ needs enables us to

create solutions to their problems.

Our dedication to the highest quality customer service within our

corporate headquarters and the service provided in the field is

unequaled. We are committed to creating the best solutions to our

customer’s needs. Above all, our employees will provide the same

respect and caring attitude within the organization as they are

expected to share with every Forney customer. Our goal will be to

exceed our customers’ expectations through empowered people,

guided by shared values and commitments.

We work hard so our customers trust us because of our integrity,

teamwork and innovation of Forney products, and Forney’s

80 years of unmatched product quality and an unwavering

commitment to our customers.

When our customers succeed we succeed.

STEVEN G. ANDERSON, President & CEO

reproduction and/or distribution is

subject to US copyright laws.

U.S. Facilities:

- Fort Collins, CO

- Tipp City, OH

FIVE WAYS TO ORDER

Web: www.forneyind.com

Phone: 800-521-6038

Fax: 970-498-9505

Mail: Forney Industries

2057 Vermont Drive

Fort Collins, CO 80525

Email: sales@forneyind.com

WWW.FORNEYIND.COM

STOP!

PLEASE DO NOT

RETURN TO THE STORE

If you have questions or problems with your new welder,

please contact customer service at 1-800-521-6038

Monday through Friday from 7 a.m. - 5 p.m. (MST) or

www.forneyind.com/about-us/contact-us.

Please take time to register your product at

www.forneyind.com/support/product-registration.

Thank you and enjoy your new welder.

For the most up-to-date

warranty information,

visit www.forneyind.com

WWW.FORNEYIND.COM

WARRANTY ................................................................................................................................................................ 3

TABLE OF CONTENTS .................................................................................................................................................. 4

SYMBOLS LEGEND ...................................................................................................................................................... 5

SAFETY SUMMARY .....................................................................................................................................................5

PRINCIPAL SAFETY STANDARDS............................................................................................................................ 5

CALIFORNIA PROPOSITION 65 WARNING ........................................................................................................... 6

EMF INFORMATION ............................................................................................................................................. 6

PERSONAL PROTECTION ...................................................................................................................................... 6

FIRE PREVENTION ................................................................................................................................................ 7

HIGH FREQUENCY RADIATION ............................................................................................................................ 8

ARC WELDING .................................................................................................................................................... 8

ELECTRIC SHOCK ................................................................................................................................................. 8

NOISE ................................................................................................................................................................. 9

ADDITIONAL SAFETY INFORMATION ................................................................................................................... 9

BOX CONTENTS ......................................................................................................................................................... 9

INSTALLATION .......................................................................................................................................................... 10

WELDER SPECIFICATIONS ................................................................................................................................. 10

SITE SELECTION ................................................................................................................................................ 10

POWER SOURCE CONNECTION ........................................................................................................................ 10

GENERATORS .................................................................................................................................................... 11

EXTENSION CORDS ........................................................................................................................................... 11

VENTILATION ..................................................................................................................................................... 11

ADDITIONAL WARNINGS .................................................................................................................................. 11

GETTING TO KNOW YOUR WELDER .......................................................................................................................... 12

DESCRIPTION ..................................................................................................................................................... 12

WELDER LAYOUT AND CONTROLS ..................................................................................................................... 12

OPERATION .............................................................................................................................................................. 14

PERFORMANCE DATA PLATE & DUTY CYCLE ....................................................................................................... 14

INTERNAL THERMAL PROTECTION ...................................................................................................................... 14

WELDING PREPARATION .................................................................................................................................... 15

SETUP FOR STICK WELDING (SMAW) ................................................................................................................. 15

SETUP FOR TIG WELDING (GTAW) WITH LIFT ARC .............................................................................................. 16

GAS SELECTION ................................................................................................................................................ 16

MAINTENANCE & SERVICING ................................................................................................................................... 17

GENERAL MAINTENANCE ................................................................................................................................. 17

TROUBLESHOOTING ................................................................................................................................................. 17

MACHINE PARTS DIAGRAM & REPLACEMENT PARTS LIST ........................................................................................... 19

TIG TORCH & TIG CONSUMABLES LIST (SOLD SEPARATELY) ........................................................................................ 20

USER NOTES ............................................................................................................................................................ 21

Box ContentsTable of Contents

WWW.FORNEYIND.COM

CAUTION!

BEFORE INSTALLING, OPERATING OR CARRYING OUT MAINTENANCE ON THE MACHINE, READ THE CONTENTS

OF THIS MANUAL CAREFULLY, PAYING PARTICULAR ATTENTION TO THE SAFETY RULES AND HAZARDS.

In the event of these instructions not being clear, please contact your

Forney Authorized Dealer or Forney Customer Service 1-800-521-6038

SYMBOL

MEANING

SYMBOL MEANING SYMBOL MEANING

ARC RAYS HAZARD

FIRE HAZARD NOISE HAZARD

POISON

HAZARD

ELECTRICAL HAZARD WARNING/CAUTION

STICK (SMAW) TIG (GTAW) TEMPERATURE

POSITIVE DINSE INPUT VOLTAGE AMPERAGE

NEGATIVE DINSE

SINGLE PHASE STATIC FREQUENCY

CONVERTER TRANSFORMER RECTIFIER

LINE CONNECTION DIRECT CURRENT (DC)

OFF

SINGLE PHASE ALTERNATING

CURRENT (AC)

SUITABLE FOR WELDING IN AN

ENVIRONMENT WITH INCREASED

RISK OF ELECTRIC SHOCK

The data within this safety summary are highlights of various safety standards. It is recommended

that you familiarize yourself with the standards listed below before beginning welding.

•

ANSI Z49.1: SAFETY IN WELDING AND CUTTING - Obtainable from the American Welding Society, 550 NW Le

Jeune Road, Miami, FL 33126 Telephone (800) 443-9353, Fax (305) 443-7559 - www.amweld.org or www.aws.

org.

• OSHA 29 CFR, Part 1910, Subpart Q.: WELDING, CUTTING AND BRAZING - Obtainable from your state OSHA

office or U.S. Dept. of Labor OSHA, Office of Public Affairs, Room N3647, 200 Constitution Ave., Washington,

DC 20210 - www.osha.gov

• AWS F4.1: SAFE PRACTICES FOR THE PREPARATION FOR WELDING AND CUTTING OF CONTAINERS AND

PIPING FOR WELDING AND CUTTING. - Obtainable from the American Welding Society, 550 NW Le Jeune

Road, Miami, FL 33126 Telephone (800) 443-9353, Fax (305) 443-7559 - www.amweld.org or www.aws.org.

• AWS A6.0. WELDING AND CUTTING CONTAINERS WHICH HAVE HELD COMBUSTIBLES - Obtainable from the

American Welding Society, 550 NW Le Jeune Road, Miami, FL 33126 Telephone (800) 443-9353, Fax (305) 443-

7559 - www.amweld.org or www.aws.org.

• NFPA 70: NATIONAL ELECTRICAL CODE - Obtainable from the National Fire Protection Association, 1

Batterymarch Park, P.O. Box 9101, Quincy, MA 02269-9101 Telephone (617) 770-3000 Fax (617) 770-0700 -

www.nfpa.org

• CGA Publication P-1: SAFE HANDLING OF COMPRESSED GASES IN CONTAINERS - Obtainable from

Compressed Gas Association, 14501 George Carter Way, Suite 103, Chantilly, VA 20151 Telephone (703) 788-

2700 Fax (703) 961-1831 - www.cganet.com

• CSA W117.2 - Code for SAFETY IN WELDING AND CUTTING. - Obtainable from Canadian Standards

Association, 178 Rexdale Blvd., Etobicoke, Ontario M9W 1R3 - www.csa.ca

Symbols Legend

Safety Summary

Principal Safety Standards

WWW.FORNEYIND.COM

• ANSI Z87.1 - SAFE PRACTICE FOR OCCUPATION AND EDUCATIONAL EYE AND FACE PROTECTION -

Obtainable from the American National Standards Institute, 11 West 42nd St., New York, NY 10036 Telephone

(212) 642A900, Fax (212) 398-0023 - www.ansi.org

• NFPA 51B: STANDARD FOR FIRE PREVENTION DURING WELDING, CUTTING, AND OTHER HOT WORK-

Obtainable from the National Fire Protection Association, 1 Batterymarch Park, P.O. Box 9101, Quincy, MA

02269-9101 Telephone (617) 770-3000 Fax (617) 770-0700 - www.nfpa.org

California Proposition 65 Warning

WARNING: This product can expose you to chemicals, including lead, which are known to the State of

California to cause cancer and birth defects or other reproductive harm. For more information go to www.

P65Warnings.ca.gov. P65 details at forneyind.com. Wash hands after use.

EMF Information

Welding current, as it flows through the welding cables, will cause electromagnetic fields. There has been and still

is some concern about such fields. However, after examination, the committee of the National Research Council

concluded that: “The body of evidence, in the committee’s judgment, has not demonstrated that exposure to

power-frequency electric and a magnetic field is a human health hazard.” However, studies are still going forth

and evidence continues to be examined. Until the final conclusions of the research are reached, you may wish to

minimize your exposure to electromagnetic fields when welding.

To reduce magnetic fields in the workplace, use the following procedures:

1. Keep electrode and ground cables close together by twisting or taping them when possible.

2. Arrange cables to one side and away from the operator.

3. Do not coil or drape cables around your body.

4. Keep welding power source and cables as far away from operator as practical.

5. Connect ground clamp to workpiece as close to the cut or weld as possible.

ABOUT PACEMAKERS & HEARING AIDS:

Pacemaker and hearing aid wearers consult your doctor first. If cleared by your doctor, then following the above

procedures is recommended.

Personal Protection

Welding processes of any kind can be dangerous not only to the operator but to any person situated near the

equipment, if safety and operating rules are not strictly observed.

THE WELDING ARC PRODUCES VERY BRIGHT ULTRAVIOLET AND INFRARED

LIGHT. THESE ARC RAYS WILL DAMAGE YOUR EYES AND BURN YOUR SKIN IF

YOU ARE NOT PROPERLY PROTECTED. To reduce the risk of injury from arc rays, read,

understand, and follow the safety instructions. In addition, make certain that anyone else that uses this welding

equipment, or is a bystander in the welding area understands and follows these safety instructions as well.

Helmets and filter should conform to ANSI Z87.1 stan dards.

• Do not look at an electric arc without proper protection. A welding arc is extremely bright and intense and, with

inadequate or no eye protection, the retina can be burned, leaving a permanent dark spot in the field of vision.

A shield or helmet with a #10 shade filter lens (minimum) must be used.

• Provide bystanders with shields or helmets fitted with an appropriate shade filter lens.

• Do not strike a welding arc until all bystanders and you (the welder) have welding shields and/or helmets in

place.

• Do not wear a cracked or broken helmet and replace any cracked or bro ken filter lenses immediately.

• Do not allow the uninsulated portion of the TIG torch to touch the ground clamp or grounded workpiece to

prevent an arc flash from being created on contact.

• Wear protective clothing. The intense light of the welding arc can burn the skin in much the same way as the

sun, even through light-weight clothing. Wear dark clothing of heavy material. The shirt worn should be long

sleeved and the collar kept buttoned to protect chest and neck.

• Protect against reflected arc rays. Arc rays can be reflected off shiny surfaces such as a glossy painted surface,

aluminum, stainless steel, and glass. It is possible for your eyes to be injured by reflected arc rays even when

wearing a protective helmet or shield. If welding with a reflective surface behind you, arc rays can bounce

off the surface and off the filter lens. It can get inside your helmet or shield and into your eyes. If a reflective

background exists in your welding area, either remove it or cover it with something non-flammable and non-

reflective. Reflective arc rays can also cause skin burn in addition to eye injury.

WWW.FORNEYIND.COM

• Flying sparks can injure. Wear proper safety equipment to protect eyes and face. Shape tungsten electrode on

grinder wearing proper protection and in a safe location. Keep flammables away and prevent fire from flying

sparks.

FUMES, GASSES, AND VAPORS CAN CAUSE DISCOMFORT, ILLNESS, AND

DEATH! To reduce the risk, read, understand, and follow the safety instructions. In addition, make certain that

anyone else that uses this welding equipment or is a bystander in the welding area, understands and follows these

safety instructions as well.

• Read and understand manufacturers Safety Data Sheets (SDS) and Material Safety Data Sheets (MSDS).

• Do not weld in an area until it is checked for adequate ventilation as described in ANSI standard Z49.1. If

ventilation is not adequate to exchange all fumes and gasses generated during the welding process with fresh

air, do not weld unless you (the welder) and all bystanders are wearing air-supplied respirators.

• Do not heat metals coated with, or that contain, materials that produce toxic fumes (such as galvanized steel),

unless the coating is removed. Make certain the area is well ventilated, and the operator and all bystanders are

wearing air-supplied respirators.

• Do not weld, cut or heat lead, zinc, cadmium, mercury, beryllium, antimony, cobalt, manganese, selenium,

arsenic, copper, silver, barium, chromium, vanadium, nickel, or similar metals without seeking professional

advice and inspection of the ventilation of the welding area. These metals produce extremely toxic fumes which

can cause discomfort, illness and death.

• Do not weld or cut in areas that are near chlorinated solvents. Vapors from chlorinated hydrocarbons, such

as trichloroethylene and perchloroethylene, can be decomposed by the heat of an electric arc or its ultraviolet

radiation. These actions can cause phosgene, a highly toxic gas to form, along with other lung and eye-

irritating gasses. Do not weld or cut where these solvent vapors can be drawn into the work area or where the

ultraviolet radiation can penetrate to areas containing even very small amounts of these vapors.

• Do not weld in a confined area unless it is being ventilated or the operator (and anyone else in the area) is

wearing an air-supplied respirator.

• Stop welding if you develop momentary eye, nose, or throat irritation as this indicates inadequate ventilation.

Stop work and take necessary steps to improve ventilation in the welding area. Do not resume welding if

physical discomfort persists.

Fire Prevention

FIRE OR EXPLOSION CAN CAUSE DEATH, INJURY, AND PROPERTY DAMAGE!

To reduce these risks, read, understand and follow the safety instructions. In addition, make certain that anyone

else that uses this welding equipment, or is a bystander in the welding area, understands and follows these safety

instructions as well. Remember: arc welding by nature produces sparks, hot spatter, molten metal drops, hot slag

and hot metal parts that can start fires, burn skin and damage eyes.

• Do not wear gloves or other clothing that contains oil, grease, or other flammable substances.

• Do not wear flammable hair preparations.

• Do not touch the hot weld bead or weld puddle until fully cooled.

• Do not weld in an area until it is checked and cleared of combustible and/or flammable materials. Be aware

that sparks and slag can fly 35 feet and can pass through small cracks and openings. If work and combustibles

cannot be separated by a minimum of 35 feet, protect against ignition with suitable, snug-fitting, fire resistant,

covers or shields.

• Do not weld on walls until checking for and removing combustibles touching the other side of the walls.

• Connect the ground cable to the workpiece as close as possible to the welding area. Do not connect ground

cables to building framing or other locations away from the welding area. This increases the possibility of

welding current passing through alternate circuits, creating fire hazards and other safety hazards.

• Do not weld, cut, or perform other such work on used barrels, drums, tanks, or other containers that had a

flammable or toxic substance. The techniques for removing flammable substance and vapors, to make a used

container safe for welding or cutting, are quite complex and require special education and training.

• Do not strike an arc on a compressed gas or air cylinder, and never allow any electrically “hot” parts to touch a

cylinder. Doing so will create a brittle area that can result in a violent rupture immediately or at a later time as a

result of rough handling.

• Ensure any compressed gas cylinders in the work area have properly operating regulators rated for the gas

and pressure used. All hoses, fittings, etc. should be in good condition.

• Do not stand in front of or put your head or face in front of a cylinder valve outlet when opening the valve.

• If a cylinder is not in use or connected for use, keep a valve protection cap in place to protect the valve.

• Keep cylinders upright and securely chain them to a fixed support to prevent tipping.

WWW.FORNEYIND.COM

• Keep cylinders away from areas where they may be subjected to physical damage or accidentally struck. Keep

them a safe distance from any source of flame, sparks, or heat.

• Do not weld or cut in an area where the air may contain flammable dust (such as grain dust), gas, or liquid

vapors (such as gasoline).

• Do not handle hot metal, such as the workpiece or electrode stubs, with bare hands.

• Wear leather gloves, heavy long sleeve shirt, cuff-less pants, high-topped shoes, helmet, and cap. As necessary,

use additional fire-resistant protective clothing to cover and protect the upper and lower body. Hot sparks or

metal can lodge in rolled up sleeves, pant cuffs, or pockets. Sleeves and collars should be kept buttoned and

pockets eliminated from the shirt front.

• Have fire extinguisher equipment handy for immediate use. A portable chemical fire extinguisher, type ABC, is

recommended.

• Wear ear plugs when welding overhead to prevent spatter or slag from falling into ear.

• Make sure welding area has a good, solid, safe floor, preferably concrete or masonry, not tiled, carpeted, or

made of any other flammable material.

• Protect flammable walls, ceilings, and floors with heat resistant covers or shields.

• Check welding area to make sure it is free of sparks, glowing metal or slag, and flames before leaving the

welding area.

• Wear garments free of oil or other flammable substances such as leather gloves, thick cotton shirts with no

synthetic materials, cuff-less trousers, closed toed shoes. Keep long hair pulled back.

• Remove any combustibles such as lighters and matches before doing any welding.

• Follow requirements in OSHA and NFPA for hot work and have an extinguisher nearby.

High Frequency Radiation

• High Frequency (H.F) can interfere with radio navigation, safety services, computers and communication

equipment.

• It is the user’s responsibility to have a qualified electrician promptly correct any interference problem resulting

from the installation. Electrician should regularly check and maintain installation.

• Stop using the equipment if notified by the FCC about interference.

• Keep H.F. source doors and panels tightly shut and keep spark gaps at correct setting.

Arc Welding

• Computers and computer driven equipment can be harmed with electromagnetic energy.

• Be sure all equipment is compatible with electromagnetic energy.

• Keep welding cables short to reduce interference.

• Follow manual to install and ground machine.

• If interference continues, shield the work area or move the welding machine.

WARNING: ELECTRIC SHOCK CAN KILL! To reduce the risk of death or serious injury from shock,

read, understand, and follow the safety instructions. In addition, make certain that anyone else who uses this

welding equipment, or who is a bystander in the welding area understands and follows these safety instructions as

well.

IMPORTANT! TO REDUCE THE RISK OF DEATH, INJURY, OR PROPERTY

DAMAGE, DO NOT ATTEMPT OPERA TION of this welding equipment until you have read and

understand the following safety summary.

• Do not, in any manner, come into physi cal contact with any part of the welding current circuit. The welding

current circuit includes:

a. the workpiece or any conductive material in contact with it,

b. the ground clamp,

c. the electrode or welding wire,

d. any metal parts on the electrode holder, or TIG torch.

• Do not weld in a damp area or come in contact with a moist or wet surface.

• Do not attempt to weld if any part of clothing or body is wet.

• Do not allow the welding equipment to come in contact with water or moisture.

Electric Shock

WWW.FORNEYIND.COM

• Do not drag welding cables, TIG torch, electrode holder or welder INPUT POWER CABLE (8) through or allow

them to come into contact with water or moisture.

• Do not touch welder, attempt to turn welder ON or OFF if any part of the body or clothing is moist or if you are

in physical contact with water or moisture.

• Do not attempt to plug the welder into the power source if any part of body or clothing is moist, or if you are in

physical contact with water or moisture.

• Do not connect ground clamp to electrical conduit, and do not weld on electrical conduit.

• Do not alter INPUT POWER CABLE or plug in any way.

• Do not attempt to plug the welder into the power source if the ground prong on INPUT POWER CABLE plug is

bent over, broken off, or missing.

• Do not allow the welder to be connected to the power source or attempt to weld if the welder, welding cables,

welding site, or welder INPUT POWER CABLE are exposed to any form of atmospheric precipitation, or salt

water spray.

• Do not carry coiled welding cables around shoulders, or any other part of the body, when they are plugged

into the welder.

• Do not modify any wiring, ground connections, switches, or fuses in this welding equipment.

• Wear welding gloves to help insulate hands from welding circuit.

• Keep all liquid containers far enough away from the welder and work area so that if spilled, the liquid cannot

possibly come in contact with any part of the welder or electrical welding circuit.

• Replace any cracked or damaged parts that are insulated or act as insulators such as welding cables, INPUT

POWER CABLE, or electrode holder immediately.

• When not welding, cut wire back to contact tip or remove electrode from electrode holder.

Noise

Noise can cause permanent hearing loss. Welding processes can cause noise levels that exceed safe limits. You

must protect your ears from loud noise to prevent permanent loss of hearing.

• To protect your hearing from loud noise, wear protective ear plugs and/or ear muffs.

• Noise levels should be measured to be sure the decibels (sound) do not exceed safe levels.

Additional Safety Information

For additional information concerning welding safety, refer to the standards listed at the

beginning of this safety summary and comply with them as applicable.

Box Contents

ITEM

DESCRIPTION

ITEM DESCRIPTION ITEM DESCRIPTION

100 ST Forney Easy Weld

™

Welder

Stick Electrode Holder

Ground Cable

and Clamp

(See page 12 for more information)

WWW.FORNEYIND.COM

Primary (input) volts 120VAC

Maximum Output 100A (DC output only)

Phase Single

Frequency 50/60Hz

Recommended Circuit Breaker 20A time-delay (slow-blow) breaker minimum

(30A for maximum performance)

Extension Cord Recommendations 3 conductor #12AWG or larger up to 25 ft.

Generator Requirements Minimum 4,000W continuous output with no low-idle

function (or low-idle off)

CSA Rated Output and Duty Cycle Refer to the data plate of your machine and the DUTY

CYCLE section of this manual, page 14.

Dimensions 12" (304.8mm) X 5.5" (139.7mm) X 10.5" (266.7mm)

Weight 9.65 lbs. (4.38 kg)

Recommended Electrode Diameter Up to 1/8”

BE SURE TO LOCATE THE WELDER ACCORDING TO THE FOLLOWING GUIDELINES:

• In areas free from moisture and dust;

• In areas with ambient temperature between 30° to 90°F;

• In areas free from oil, steam and corrosive gases;

• In areas not subjected to abnormal vibration or shock;

• In areas not exposed to direct sunlight or rain;

• Place at a distance of 12” or more from walls or similar obstructions that could restrict natural air flow for

cooling.

Before you make any electrical connection, make sure that the ON/OFF SWITCH (7) is OFF, power supply voltage

and frequency available at site are those stated in the ratings label of your welder.

The main power supply voltage should be within ±10% of the rated main power supply voltage. Too low a power

supply voltage may cause poor welding performance. Too high a power supply voltage will cause components to

overheat and possibly fail. The welder outlet must be:

• Correctly installed, if necessary, by a qualified electrician;

• Correctly grounded (electrically) in accordance with national and local regulations;

• Connected to an electric circuit that is rated for sufficient amperage per the ratings label of your welder.

If you are unsure of any of the above, have your outlet inspected by a qualified electrician before using the welder.

NOTE:

• Periodically inspect INPUT POWER CABLE (8) for any cracks or exposed wires. If it is not in good condition,

have it repaired by a Service Center.

• Do not cut off the grounding prong or alter the plug in any way and do not use any adapters between the

welder’s INPUT POWER CABLE and the power source receptacle.

• Do not violently pull the INPUT POWER CABLE to disconnect it from power outlet.

• Do not lay material or tools on the INPUT POWER CABLE. The INPUT POWER CABLE may be damaged and

result in electrical shock.

• Keep the INPUT POWER CABLE away from heat sources, oils, solvents or sharp edges.

• Do not use this welder on a circuit with a Ground Fault Circuit Interrupter (GFCI) on it. GFCIs are tripped by

welding arcs and your welding operations will be interrupted regularly.

Installation

Welder Specifications

Site Selection

Power Source Connection

WWW.FORNEYIND.COM

Generators

This welder can be operated from an AC generator. Ensure that the generator can supply a minimum of 4,000

watts of continuous output. The generator must not have an auto-idle fuel saving feature or must have the option to

turn auto-idle off. The generator must run at full speed at all times while your welder is plugged into it or you risk

damaging your welder. Any other power draws on the generator or anything that reduces the generator RPM may

damage your welder.

Extension Cords

For optimum welder performance, an extension cord should not be used unless absolutely necessary. If necessary,

care must be taken in selecting an extension cord appropriate for use with your specific welder.

Select a properly grounded extension cord that will mate directly with the AC power source receptacle and the

welder INPUT POWER CABLE (8) without the use of adapters. Make certain that the extension cord is properly

wired and in good electrical condition. Extension cords must fit the following wire size guidelines:

• #12 AWG or larger wire

• Do not use an extension cord over 25 ft. in length.

Since the inhalation of welding fumes can be harmful, ensure that the welding area is effectively ventilated. See the

“Safety Summary” for more details (pages 5-9).

FOR YOUR SAFETY, BEFORE CONNECTING THE POWER SOURCE TO THE LINE

CLOSELY FOLLOW THESE INSTRUCTIONS:

• An adequate two-pole breaker must be inserted before the main outlet. This breaker must be equipped with

time-delay fuses.

• When working in a confined space, the welder must be kept outside the welding area and the ground cable

should be fixed to the workpiece. Never work in a damp or wet confined space.

• Do not use damaged INPUT POWER CABLE (8) or welding cables.

• The welding torch/electrode should never be pointed at the operator or other people.

• The welder must never be operated without its panels attached. This could cause serious injury to the operator

and could damage the equipment.

Ventilation

Additional Warnings

WWW.FORNEYIND.COM

Description

Your new single phase inverter welder offers Stick and TIG welding processes in the same power source. These

processes can be selected with the process SELECTOR SWITCH (1) on the front panel of the unit.

Stick Welding, “SMAW”

Both rutile and basic electrodes can be welded. Welding current is adjusted using the AMPERAGE ADJUSTMENT

KNOB (4).

TIG Welding, “GTAW”

In the TIG position, a TIG torch with a gas valve in the handle is required. The gas valve must be opened manually

before welding and closed manually when welding is completed. The arc is activated using a lift arc technique.

Using the AMPERAGE ADJUSTMENT KNOB, welding current can be adjusted.

Welder Layout and Controls

1. SELECTOR SWITCH for the welding process selection:

a. STICK (“SMAW”)

STICK

(“SMAW”)

TIG

(“GTAW”)

b. TIG (“GTAW”)

2. INPUT VOLTAGE INDICATOR LED will be illuminated when input voltage to the machine is present

and the ON/OFF SWITCH (11) is in the ON position.

3. FAULT/THERMAL OVERLOAD INDICATOR LED will be illuminated under the following conditions:

a. The duty cycle of the machine has been exceeded or air flow is blocked. The fan will continue to run until

the machine has cooled, but output power will be disabled. Ensure that the cooling fan is running and that

there are 12 inches of clearance around all vents. When the LED turns off, welding power will be enabled

again.

b. The input voltage is outside of the acceptable range. If this indicator remains illuminated for more than 10

minutes, it is likely that there is an input voltage problem.

4. AMPERAGE ADJUSTMENT KNOB is used to adjust the following welding parameters:

a. In STICK (“SMAW”) Mode it adjusts welding current (amperage) from 15A to 80A.

b. In TIG, (“GTAW”) Mode it adjusts welding current (amperage) from 10A to 85A.

5. NEGATIVE (-) DINSE SOCKET

6. POSITIVE (+) DINSE SOCKET

7. ON/OFF SWITCH

8. INPUT POWER CABLE

Getting to Know Your Welder

WWW.FORNEYIND.COM

1 2

—

WWW.FORNEYIND.COM

Performance Data Plate and Duty Cycle

On the machine, there is a plate that includes all the operating specifications for your new unit. The serial number

of the product is also found on this plate.

The duty cycle rating of a welder defines how long the operator can weld and how long the welder must rest and be

cooled. Duty cycle is expressed as a percentage of 10 minutes and represents the maximum welding time allowed.

The balance of the 10-minute cycle is required for cooling.

For example, a welder has a duty cycle rating of 30% at the rated output of 90A. This means with that machine,

you can weld at 90 A output for three (3) minutes out of 10 with the remaining seven (7) minutes required for

cooling. The duty cycle of your new welder can be found on the data plate affixed to the machine. It looks like the

diagram below. Referring to the sample below, the “X” row lists duty cycle percentages while the “I

” row lists the

amp draw corresponding to the duty cycle. Various duty cycles at other amperages are listed on your data plate.

X 100%

##A

##.#V

X 100%

##A

##.#V

min #A/min #V – max #A/max #V

Y% Z%

100 ST SER #:

CSA-C22.2 NO 60-M1990

UL551 (8 Ed.)

o=##.#V

##A ##A

##.#V ##.#V

1=120V I

1max

=##.#A I

1eff

=##.#A

min #A/min #V – max #A/max #V

Y% Z%

o=##.#V

##A ##A

##.#V ##.#V

1=120V I

1max

=##.#A I

1eff

=##.#A

IP21S

(Example Data Plate)

If you exceed the duty cycle of the welder, the thermal protection system will engage, shutting off all welder output.

After cooling, the thermal protector will automatically reset and the welding functions can resume. This is normal

and automatic behavior of the machine, and does not require any user action. However, you should wait at least

ten minutes after the thermal protector engages before resuming welding. You must do this even if the thermal

protector resets itself before the ten minutes is up or you may experience less than specified duty cycle performance.

CAUTION: DO NOT REGULARLY EXCEED THE DUTY CYCLE OR DAMAGE TO THE

WELDER CAN RESULT.

Operation

Internal Thermal Protection

WWW.FORNEYIND.COM

An important factor in making a satisfactory weld is preparation. This includes studying the process and equipment

and practicing welding before attempting to weld finished product. An organized, safe, ergonomic, comfortable,

and well-lit work area should be prepared for the operator. The work area should specifically be free of all

flammables with both a fire extinguisher and a bucket of sand available.

To properly prepare for welding with your new welder, it is necessary to:

• Read the safety precautions at the front of this manual.

• Prepare an organized, well-lit work area.

• Provide protection for the eyes and skin of the operator and bystanders.

• Attach the ground clamp to the bare metal to be welded, making sure of good contact.

• Plug the machine into a suitable outlet.

• Completely open the gas cylinder valve. Adjust the gas pressure regulator to the correct flow rate. (Not

applicable to Stick “SMAW” process.)

EXPOSURE TO A WELDING ARC IS EXTREMELY HARMFUL TO THE EYES AND

SKIN. PROLONGED EXPOSURE TO A WELDING ARC CAN CAUSE BLINDNESS

AND BURNS. NEVER STRIKE AN ARC OR BEGIN WELDING UNLESS YOU ARE

ADEQUATELY PROTECTED. WEAR FIRE RESISTANT WELDING GLOVES, HEAVY

LONG SLEEVED SHIRT, CUFF-LESS PANTS; HIGH TOPPED SHOES AND A

WELDING HELMET.

• Switch the Process SELECTOR SWITCH (1) on the front panel to the left position.

• Check the electrode packaging to determine the recommended polarity and connect the electrode holder and

ground clamp to the POSITIVE (+) and NEGATIVE (-) DINSE SOCKETS (6 and 5) accordingly.

• Direct current electrode positive (DCEP) or direct current reverse polarity (DCRP): electrode holder in POSITIVE

(+) DINSE SOCKET, ground clamp in NEGATIVE (-) DINSE SOCKET. Most electrodes use DCEP.

• Direct current electrode negative (DCEN) or direct current straight polarity (DCSP): electrode holder in

NEGATIVE (-) DINSE SOCKET, ground clamp in POSITIVE (+) DINSE SOCKET

• Ensure the ground clamp has a good connection to the workpiece and is connected on clean, bare metal (not

rusty or painted).

• Secure the bare end of the welding electrode in-to the jaws of the electrode holder.

• Switch the unit ON with the ON/OFF SWITCH (7).

• Set the amperage with the AMPERAGE ADJUSTMENT KNOB (4).

Regulation Knob

Mild Steel

E6010 – – 50-70A 80A

E6011,

E6013,

E6014

30-40A 40-60A 50-70A 70-80A

E7018 – – 70-80A 80A (Difficult)

Stainless Steel

E308L – – 40-70A 50-80A

CANNOT WELD ALUMINUM

MATERIAL

(Wire)

ELECTRODE

TYPE

ELECTRODE DIAMETER

1/16” (1.6 mm) 5/64” (2 mm) 3/32” (2.4 mm) 1/8” (3 mm)

100 ST STICK SET-UP CHART

Welding Preparation

Setup for Stick Welding (SMAW)

WWW.FORNEYIND.COM

Setting up the Equipment for TIG Welding (GTAW):

Lanthanated Tungsten 1/16” or 3/32” (MAX) recommended for use.

WARNING: TIG TORCH IS ALWAYS LIVE (ELECTRICALLY HOT). Use caution and ensure

the TIG torch is not in contact with or near conductive or grounded materials.

• Switch the Process SELECTOR SWITCH (1) on the front panel to the right position.

• Connect the TIG torch cable to the NEGATIVE (-) DINSE SOCKET (5) of the welder.

• Connect the ground cable connector to the POSITIVE (+) DINSE SOCKET (6) of the welder.

• Ensure the ground clamp has a good connection to the workpiece and is connected on clean, bare metal (not

rusty or painted).

• Connect the TIG torch gas line to the gas regulator (argon gas only).

THE GAS FLOW IS MANUALLY CONTROLLED WITH THE KNOB ON THE TIG

TORCH. USE INERT GAS (ARGON) ONLY.

TURN ON GAS AT THE GAS REGULATOR, THEN OPEN THE VALVE ON THE TORCH

HANDLE, CHECK FOR GAS FLOW AND ADJUST FLOW RATE AS NEEDED.

• Fix the tungsten electrode so that it protrudes approximately ¼ inch from the torch nozzle.

• Ensure the TIG torch is safely away from all conductive materials.

• Switch the unit ON with the ON/OFF SWITCH (7).

• Set the amperage with the AMPERAGE ADJUSTMENT KNOB (4).

• Open the gas valve on the torch handle.

• Initiate the weld arc with a lift arc technique.

• Close the gas valve on the torch handle after post-weld flow has been completed.

REMEMBER TO CLOSE THE VALVE ON THE GAS CYLINDER IMMEDIATELY AFTER

ALL WELDING IS COMPLETED.

Regulation Knob

Mild Steel

100% Argon 1/16” (1.6 mm) 10-15A 15-20A 35-50A 60-80A

CANNOT WELD ALUMINUM

MATERIAL

(Wire)

GAS

TUNGSTEN

ELECTRODE

MATERIAL THICKNESS

22 Gauge

.030” (.8 mm)

16 Gauge

1/16” (1.6 mm) 1/8” (3 mm) 3/16” (5 mm)

100 ST TIG SET-UP CHART

Welding Tips:

• Always weld clean, dry and well-prepared material.

• Move the torch smoothly and steadily as you weld.

• Avoid welding in very drafty areas. A weak, pitted and porous weld will result due to drafts blowing away the

protective welding gas.

• Sharp bends or kinks in the welding cable should be avoided.

• The diameter of the welding electrode should be approximately the same as the thickness of the metal to be

welded.

• The packaging of the welding electrode typically gives a recommended range for the welding current. Set the

amperage accordingly.

Use 100% argon gas when TIG welding with mild steel or stainless steel.

NOTE: THIS MACHINE IS NOT AN APPROPRIATE POWER SOURCE FOR WELDING ALUMINUM.

Setup for TIG Welding (GTAW) with Lift Arc

Gas Selection

WWW.FORNEYIND.COM

This welder has been engineered to need minimal service providing that a few very simple steps are taken to properly

maintain it.

1. Replace INPUT POWER CABLE (8), ground cable, ground clamp, or torch/electrode cable when damaged or

worn.

2. Avoid directing grinding particles towards the welder. These conductive particles can build up inside the machine

and cause severe damage.

3. Periodically clean dust, dirt, grease, etc. from your welder. Every six months or as necessary, remove the side

panels from the welder and use compressed air to blow out any dust and dirt that may have accumulated inside

the welder.

WARNING: DISCONNECT FROM POWER SOURCE WHEN CARRYING OUT THIS

OPERATION.

4. Check all cables periodically. They must be in good condition and not cracked.

WARNING: ELECTRIC SHOCK CAN KILL! Be aware that the ON/OFF SWITCH (7), when OFF, does

not remove power from all internal circuitry in the welder. To reduce the risk of electric shock, always unplug the

welder from its AC power source and wait several minutes for electrical energy to discharge before removing side

panels.

The following is a troubleshooting table provided to help you determine a possible remedy when you are

having a problem with your welder.

This table does not provide all possible solutions, only those possibilities considered likely to be common

faults.

PROBLEM

POSSIBLE CAUSE POSSIBLE SOLUTION

Neither INDICATOR LED is

illuminated and nothing works

on the welder.

Machine is not turned ON. Turn machine ON with ON/OFF SWITCH

(7).

No input power present. Make sure machine is plugged in.

Verify that circuit breaker has not been

tripped. Reset if needed.

Verify output power from the outlet.

Do not use the machine on a GFI outlet.

Both INDICATOR LEDS are

illuminated and there is no

output power from the welder.

Exceeded duty cycle; thermal protector

engaged.

Allow welder to cool at least 10 minutes

with machine ON (observe and maintain

proper duty cycle). FAULT/THERMAL

OVERLOAD INDICATOR LED (3) should

turn off after the machine has cooled.

Insufficient air flow causing machine to

overheat before reaching duty cycle.

Check for obstructions blocking air flow

and ensure that there are 12 inches of

clearance between any obstacles and the

vents on all sides of the machine.

Incorrect voltage supplied to welder. Check the voltage of your outlet. If it

is 10% more or less than 120V, call a

qualified electrician.

Maintenance & Servicing

General Maintenance

Troubleshooting

WWW.FORNEYIND.COM

PROBLEM

POSSIBLE CAUSE POSSIBLE SOLUTION

Low output or non-penetrating

weld.

Weld parameters too low. Adjust welding parameters

Too long or improper extension cord. Use a proper extension cord (#12 AWG

wire or heavier, no longer than 25 ft.). See

“Extension Cords”, page 11.

Poor ground connection or torch/electrode

connection.

Reposition clamp and check cable to

clamp connection.

Check connection of ground cable, torch

or electrode holder

Input power too low. Have a qualified electrician verify the

voltage at your outlet. If the voltage is

appropriate, verify that the circuit wiring is

sufficient for 20A.

Ground clamp, ground cable,

and/or welding cable get hot.

Bad ground or loose ground connection. Check connection of ground cable, torch

or electrode holder.

Check connection of the ground cable

to the ground clamp. Tighten cable

connection to ground clamp if needed.

Ensure the connection between the ground

clamp and workpiece is good and on

clean, bare (not painted or rusted) metal.

Frequent circuit breaker trips.

Machine is not the only piece of electrical

equipment on the circuit.

Make sure the welder is on a dedicated

circuit or is the only thing plugged on a

circuit.

Circuit breaker is incorrect/insufficient for

use with this machine.

Verify that the circuit breaker for the circuit

is a 20A time-delay (slow-blow) breaker. If

it is not, have a qualified electrician install

the proper breakers.

Poor quality welds.

Insufficient gas at weld area. Check that the gas is not being blown

away by drafts and, if so, move to a more

sheltered weld area. If not, check gas

cylinder contents, gauge, regulator setting,

and operation of gas valve.

Rusty, painted, oily or greasy workpiece. Ensure workpiece is clean and dry.

Poor ground connection or torch/electrode

connection.

Check ground clamp/workpiece

connection and all connections to the

machine.

Difficult arc start.

Amperage is too low. Increase amperage setting.

Arc is wandering (TIG).

Tungsten is too large. Use a smaller tungsten.

WWW.FORNEYIND.COM

NO. PART NUMBER ITEM DESCRIPTION

85667 Ground (25 Dinse)

85669 Electrode Holder (25 Dinse)

Machine Parts Diagram & Replacement Parts List

WWW.FORNEYIND.COM

NO. PART NUMBER ITEM DESCRIPTION ITEM PHOTO

1 85657 Tig Torch (9FV)

2 85454 Cup (10N48)

3 85455 Collet (10N23 (1/16in))

4 85459 Collet Body (10N31 (1/16in))

5 85465 Back Cap (57Y02 (4in))

6 85450 Electrode (1/16” x 7”)

TIG Torch & TIG Consumables List (SOLD SEPARATELY)

La page charge ...

Forney 298 Manuel utilisateur

Marque: Forney

Modèle: 298

Catégorie: Système de soudage

Taper: Manuel utilisateur

Ce manuel convient également à

298 100 ST Easy Weld

Télécharger le PDF

rapport

dans d''autres langues

English: Forney 298 User manual
español: Forney 298 Manual de usuario

Forney 298 Manuel utilisateur

Ce manuel convient également à

Forney 298 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents