LG DLEX5175W Le manuel du propriétaire

OWNER’S MANUAL

DRYER

Please read this owner’s manual thoroughly before operating and

keep it handy for reference at all times.

MFL62512878

www.lg.com

ENGLISH FRANÇAIS

DLEX5170*

DLEX5175*

DLGX5171*

DLGX5176*

MFL62512878_en_150603.indd 1 2015.6.3 3:43:4 PM

2

TABLE OF CONTENTS

3

IMPORTANT SAFETY INSTRUCTIONS

3 WHAT TO DO IF YOU SMELL GAS

4 BASIC SAFETY PRECAUTIONS

5 GROUNDING INSTRUCTIONS

5 SAFETY INSTRUCTIONS FOR INSTALLATION

7 SAFETY INSTRUCTIONS FOR CONNECTING

ELECTRICITY

8

PRODUCT FEATURES

9

INTRODUCING YOUR DRYER

9 Parts

9 Accessories

10 Control Panel Features

11 Display

12

INSTALLATION INSTRUCTIONS

12 Preview Installation Order

13 Installation Location Requirements

13 Clearances

14 Leveling the Dryer

15 Reversing the Door

16 Installing the Side Vent Kit

17 Venting the Dryer

19 Connecting Gas Dryers

21 Connecting Electric Dryers

22 Special Requirements for Manufactured or

Mobile Homes

22 Final Installation Check

23 Installation Test (Duct Check)

25

HOW TO USE

25 Operating the Dryer

26 Cycle Guide

27 Sorting Load

27 Loading the Dryer

27 Check the Lint Filter Before Every Load

28 Cycle Settings and Options

28 Special Functions

29 Custom Program

29 Steam Functions

32

MAINTENANCE

32 Regular Cleaning

33

TROUBLESHOOTING

33 Before Calling for Service

36

SPECIFICATIONS

37

USING SMART DIAGNOSIS™

38

WARRANTY

MFL62512878_en_150603.indd 2 2015.6.3 3:43:4 PM

3

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

w

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric

shock, or to prevent property damage, injury to persons, or death.

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word DANGER, WARNING, or CAUTION.

These words mean:

w

DANGER

You will be killed or seriously injured if you don’t immediately follow instructions.

w

WARNING

You can be killed or seriously injured if you don’t follow instructions.

w

CAUTION

You may be slightly injured or cause damage to the product if you do not follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell

you what can happen if the instructions are not followed.

• Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is

installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with

clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These

conditions will obstruct clothes dryer airflow and increase the risk of fire.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this appliance or any

other appliances.

• Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

• Install the clothes dryer according to the manufacturer’s instructions and local codes.

• Save these instructions.

WHAT TO DO IF YOU SMELL GAS:

1. Do not try to light a match or cigarette, or turn on any gas or electrical appliance.

2. Do not touch any electrical switches. Do not use any phone in your building.

3. Clear the room, building, or area of all occupants.

4. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions carefully.

5. If you cannot reach your gas supplier, call the fire department.

IMPORTANT SAFETY INSTRUCTIONS

w

MFL62512878_en_150603.indd 3 2015.6.3 3:43:4 PM

4

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

w

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric

shock, or to prevent property damage, injury to persons, or death.

BASIC SAFETY PRECAUTIONS

w

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,

including the following:

• Read all instructions before using the dryer.

• Before use, the dryer must be properly installed as

described in this manual.

• Do not place items exposed to cooking oils in your

dryer. Items contaminated with cooking oils may

contribute to a chemical reaction that could cause a

load to catch fire.

• Do not dry articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline, dry-

cleaning solvents, or other flammable or explosive

substances as they give off vapors that could ignite or

explode.

• Do not reach into the dryer if the drum or any other

part is moving.

• Do not repair or replace any part of the dryer

or attempt any servicing unless specifically

recommended in this owner’s manual or in published

user-repair instructions that you understand and have

the skills to carry out.

• Do not tamper with controls.

• Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

• Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

• Do not use fabric softeners or products to eliminate

static unless recommended by the manufacturer of

the fabric softener or product.

• Do not use heat to dry articles containing foam rubber

or similarly textured rubber-like materials.

• Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint,

dust, and dirt.

• The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

• Do not install or store the dryer where it will be

exposed to the weather.

• Always check the inside of the dryer for foreign

objects.

• Clean lint screen before or after each load.

• Do not store plastic, paper, or clothing that may

burn or melt on top of the dryer during operation.

IMPORTANT SAFETY INSTRUCTIONS

MFL62512878_en_150603.indd 4 2015.6.3 3:43:4 PM

5

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

w

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric

shock, or to prevent property damage, injury to persons, or death.

GROUNDING INSTRUCTIONS

w

WARNING

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a

qualified electrician or service person if you are in doubt that the appliance is properly grounded.

SAFETY INSTRUCTIONS FOR INSTALLATION

w

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,

including the following:

• Properly ground dryer to conform with all

governing codes and ordinances. Follow details in

the installation instructions. Electric shock can result if

the dryer is not properly grounded.

• Before use, the dryer must be properly installed as

described in this manual. Electric shock can result if

the dryer is not properly grounded.

• Install and store the dryer where it will not be

exposed to temperatures below freezing or

exposed to the weather.

• All repairs and servicing must be performed

by an authorized servicer unless specifically

recommended in this owner’s manual. Use only

authorized factory parts. Failure to follow this

warning can cause serious injury, fire, electric shock, or

death.

• To reduce the risk of electric shock, do not install

the dryer in humid spaces. Failure to follow this

warning can cause serious injury, fire, electric shock, or

death.

• Connect to a properly rated, protected, and sized

power circuit to avoid electrical overload. Improper

power circuit can melt, creating electric shock and/or

fire hazard.

• Remove all packing items and dispose of all

shipping materials properly. Failure to do so can

result in death, explosion, fire, or burns.

• Place dryer at least 18 inches above the floor for

a garage installation. Failure to do so can result in

death, explosion, fire, or burns.

• Keep all packaging from children. Packaging

material can be dangerous for children. There is a risk

of suffocation.

• Do not install near another source of heat such as

a stove, cooking oven. Failure to do so can cause

deform, smoke and fire.

• Do not place candles, smoking materials, or other

flammables on top of the product. Dripping wax,

smoke, or fire can result.

• Remove all protective vinyl film from the product.

Failure to do so can cause product damage, smoke or

fire.

This appliance must be grounded. In the event of

malfunction or breakdown, grounding will reduce

the risk of electric shock by providing a path of least

resistance for electric current. This appliance must be

equipped with a cord having an equipment-grounding

conductor and a grounding plug. The plug must be

plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local

codes and ordinances.

Do not modify the plug provided with the appliance. If

it will not fit the outlet, have a proper outlet installed by

a qualified electrician.

This appliance must be connected to a grounded metal,

permanent wiring system or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or

lead on the appliance.

Electric shock can result if the dryer is not properly

grounded.

IMPORTANT SAFETY INSTRUCTIONS

MFL62512878_en_150603.indd 5 2015.6.3 3:43:5 PM

6

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

w

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric

shock, or to prevent property damage, injury to persons, or death.

SAFETY INSTRUCTIONS FOR INSTALLATION

w

WARNING

To reduce the risk of injury to persons, follow all industry recommended safety procedures including the use of long

sleeved gloves and safety glasses. Failure to follow all of the safety warnings in this manual could result in property

damage, injury to persons, or death.

Exhaust/Ducting:

• Gas dryers MUST be exhausted to the outside.

Failure to follow these instructions can result in fire or

death.

• The dryer exhaust system must be exhausted

to the outside of the dwelling. If the dryer is not

exhausted outdoors, some fine lint and large

amounts of moisture will be expelled into the

laundry area. An accumulation of lint in any area of

the home can create a health and fire hazard.

• Use only rigid metal or flexible metal 4-inch

diameter ductwork inside the dryer cabinet or for

exhausting to the outside. Use of plastic or other

combustible ductwork can cause a fire. Punctured

ductwork can cause a fire if it collapses or becomes

otherwise restricted in use or during installation.

• Ductwork is not provided with the dryer, and you

should obtain the necessary ductwork locally. The

end cap should have hinged dampers to prevent

backdraft when the dryer is not in use. Failure to

follow these instructions can result in fire or death.

• The exhaust duct must be 4 inches (10.2 cm) in

diameter with no obstructions. The exhaust duct

should be kept as short as possible. Make sure

to clean any old ducts before installing your new

dryer. Failure to follow these instructions can result in

fire or death.

• Rigid or semi-rigid metal ducting is recommended

for use between the dryer and the wall. In special

installations when it is impossible to make a

connection with the above recommendations, a UL-

listed flexible metal transition duct may be used

between the dryer and wall connection only. The

use of this ducting will affect drying time. Failure to

follow these instructions can result in fire or death.

• DO NOT use sheet metal screws or other fasteners

which extend into the duct that could catch lint and

reduce the efficiency of the exhaust system. Secure

all joints with duct tape. For complete details, follow

the Installation Instructions. Failure to follow these

instructions can result in fire or death.

IMPORTANT SAFETY INSTRUCTIONS

MFL62512878_en_150603.indd 6 2015.6.3 3:43:5 PM

7

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

w

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric

shock, or to prevent property damage, injury to persons, or death.

SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY

w

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,

including the following:

SAVE THESE INSTRUCTIONS

• Do not, under any circumstances, cut or remove

the ground prong from the power cord. To prevent

injury to persons or damage to the dryer, the electrical

power cord must be plugged into a properly grounded

outlet.

• For personal safety, this dryer must be properly

grounded. Failure to do so can result in electric shock

or injury.

• Refer to the installation instructions in this manual

for specific electrical requirements for your model.

Failure to follow these instructions can create an

electric shock hazard and/or a fire hazard.

• This dryer must be plugged into a properly

grounded outlet. Electric shock can result if the

dryer is not properly grounded. Have the wall

outlet and circuit checked by a qualified electrician

to make sure the outlet is properly grounded.

Failure to follow these instructions can create an

electric shock hazard and/or a fire hazard.

• The dryer should always be plugged into its own

individual electrical outlet which has a voltage

rating that matches the rating plate. This provides

sparkling performance and also prevents overloading

house wiring circuits which could cause a fire hazard

from overheated wires.

• Never unplug your dryer by pulling on the power

cord. Always grip plug firmly and pull straight out

from the outlet. The power cord can be damaged,

resulting in a risk of fire and electric shock.

• Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end. The power cord can

melt, creating an electric shock and/or fire hazard.

• When installing or moving the dryer, be careful not

to pinch, crush, or damage the power cord. This will

prevent injury and prevent damage to the dryer from

fire and electric shock.

IMPORTANT SAFETY INSTRUCTIONS

MFL62512878_en_150603.indd 7 2015.6.3 3:43:5 PM

8

PRODUCT FEATURES

EASY-TO-USE CONTROL PANEL

Rotate the cycle selector knob to select the desired dry cycle. Add cycle options or adjust settings with the touch

of a button.

EASY-ACCESS REVERSIBLE DOOR

The wide-opening door provides easy access for loading and unloading. The door hinge can be reversed to adjust

for installation location.

STEAM FUNCTIONS

LG’s steam technology allows you to inject fabrics with a swirling jet of hot steam to refresh clothes, reduce static,

and make ironing easier. Simply select the Steam Fresh™ cycle, or you can add a Steam option to selected cycles.

FLOW SENSE™ DUCT BLOCKAGE SENSING SYSTEM INDICATOR

The FLOW SENSE™ duct blockage sensing system detects and alerts you to restrictions in the installed household

ductwork that reduce exhaust airflow through the dryer. If you see the alert: Clean or repair the ducts to remove

the restrictions. Keep your ducts clean to help increase efficiency and reduce long drying times caused by blocked

ducts.

SMART DIAGNOSIS™

Should you experience any technical difficulty with your dryer, it has the capability of transmitting data via your

telephone to the Customer Information Center. The call center agent records the data transmitted from your

machine and uses it to analyze the issue, providing a fast and effective diagnosis.

Protocol P154

Sanitization Performance of

Residential Clothes dryer

C

E

R

T

I

F

I

E

D

E

S

I

G

N

PRODUCT FEATURES

MFL62512878_en_150603.indd 8 2015.6.3 3:43:6 PM

9

ENGLISH

INTRODUCING YOUR DRYER

Parts

Accessories

Control

panel

Leveling

feet

Reversible

door

Lint filter

Terminal

block

access panel

(Electric

models)

Gas

connection

location

(Gas models)

Power cord

location

(Gas

models)

Exhaust

duct

outlet

NOTE

• Contact LG Customer Service at 1-800-243-0000 (1-888-542-2623 in Canada) if any accessories are missing.

• For your safety and for extended product life, use only authorized components. The manufacturer is not

responsible for product malfunction or accidents caused by the use of separately purchased unauthorized

components or parts.

• The images in this owner’s manual may be different from the actual components and accessories, and are

subject to change by the manufacturer without prior notice for product improvement purposes.

INTRODUCING YOUR DRYER

Included accessories

Drying rack

MFL62512878_en_150603.indd 9 2015.6.3 3:43:8 PM

10

Control Panel Features

Following are instructions for starting and using your new dryer. Please refer to specific sections of this manual for

more detailed information.

w

WARNING

To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the Important Safety

Instructions, before operating this dryer.

INTRODUCING YOUR DRYER

B

C

H

G

DE

A

F

NOTE

Pressing the ON/OFF button during a cycle will

cancel that cycle and any load settings will be lost.

NOTE

If you do not press the START/PAUSE button to

resume a cycle within 4 minutes, the dryer turns

off automatically.

A

POWER ON/OFF BUTTON

Press to turn the dryer ON. Press again to turn the

dryer OFF.

E

CYCLE SETTING BUTTONS

Use these buttons to select the desired cycle

settings for the selected cycle. The current settings

are shown in the display. Press the button for that

option to view and select other settings.

F

TIME AND STATUS DISPLAY

The display shows the settings, estimated time

remaining, options, and status messages for your

dryer.

G

OPTION BUTTONS

The OPTION buttons allow you to select additional

cycle options. Certain buttons also allow you to

activate special functions by pressing and holding

the button for 3 seconds.

H

STEAM FUNCTIONS

LG’s steam technology allows you to inject fabrics

with a swirling jet of hot steam to refresh clothes,

reduce static, and make ironing easier. Simply select

the steam fresh™ cycle, or you can add a STEAM

option to selected cycles.

B

CYCLE SELECTOR KNOB

Turn this knob to select the desired cycle. Once

the desired cycle has been selected, the standard

presets will be shown in the display. On MANUAL

DRY cycles, these settings can be adjusted using

the cycle setting buttons anytime before starting

the cycle.

C

START/PAUSE BUTTON

Press this button to START the selected cycle. If the

dryer is running, use this button to PAUSE the cycle

without losing the current settings.

D

MORE TIME/LESS TIME BUTTONS

To adjust the drying time, use these buttons with

MANUAL DRY, TIME DRY, and STEAM FRESH™ cycles,

as well as the REDUCE STATIC and EASY IRON

options. Press the MORE TIME button to increase the

selected manual cycle time by a minute; press LESS

TIME to decrease the cycle time by a minute.

MFL62512878_en_150603.indd 10 2015.6.3 3:43:11 PM

11

ENGLISH

Display

The display shows the settings, estimated time remaining, options, and status messages for your dryer. When the

dryer is turned on, the light in the display will illuminate.

w

WARNING

To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the Important Safety

Instructions, before operating this dryer.

INTRODUCING YOUR DRYER

NOTE

The cycle time on SENSOR DRY cycles may

fluctuate as the dryer recalculates drying time for

optimal results.

A

ESTIMATED TIME REMAINING

When the START/PAUSE button is pressed, the dryer

will display the estimated (SENSOR DRY) or set time

(TIME DRY) remaining, and begin tumbling.

E

CHECK FILTER REMINDER

The display will show CHECK FILTER when the dryer

is turned on as a reminder to check the filter. It turns

off when the START/PAUSE button is pressed.

F

CUSTOM PROGRAM

If you have a special combination of settings that

you use frequently, you can save these settings as a

CUSTOM PROGRAM.

G

FLOW SENSE™ DUCT BLOCKAGE

SENSING SYSTEM INDICATOR

The FLOW SENSE™ duct blockage sensing system

detects and alerts you to blockages in the ductwork

that reduce exhaust flow from the dryer. This

improves operating efficiency and helps minimize

service calls, saving your money.

B

CYCLE COMPLETION INDICATOR WITH

CHECK FILTER REMINDER

This portion of the display shows which stage of the

drying cycle is currently underway (CHECK FILTER,

DRYING, COOLING, or WRINKLE CARE).

C

CHILD LOCK INDICATOR

When CHILD LOCK is set, the CHILD LOCK indicator

will appear and all buttons are disabled except

the POWER button. This prevents children from

changing settings while the dryer is operating.

D

ADD WATER INDICATOR

If the steam feeder is low on water, this error may

be displayed. Fill the feeder and restart the cycle.

B

C

H

G

DE

A

F

B

C

H

G

DE

A

F

C A

F

G

B

D

E

MFL62512878_en_150603.indd 11 2015.6.3 3:43:16 PM

12

INSTALLATION INSTRUCTIONS

Preview Installation Order

INSTALLATION INSTRUCTIONS

Checking and choosing the

proper location

Leveling the dryer Venting the dryer

Plugging in the power cord

and grounding

Connecting gas dryers

Test run

Installation test

(Refer to page 23.)

Press and hold

120V 240V(USA)

230V(CANADA)

MFL62512878_en_150603.indd 12 2015.6.3 3:43:18 PM

13

ENGLISH

Installation Location Requirements

w

WARNING

Read all installation instructions completely before installing and operating your dryer! It is important that

you review this entire manual before installing and using your dryer. Detailed instructions concerning electrical

connections, gas connections, and exhaust requirements are provided on the following pages.

Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off

at the end of an automatic cycle. This can result in longer drying times. The dryer must not be installed or stored in

an area where it will be exposed to water and/or weather. Check code requirements. Some codes limit, or do not

permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building

inspector.

Clearances

Installation Spacing For Recessed Area Or Closet Installation

The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of

1 inches(2.54cm) clearance on the sides and rear. Recommended spacing should be considered for the following

reasons:

• A location that allows for proper exhaust installation. A

gas dryer must be exhausted to the outdoors.

See Venting the dryer.

• A grounded electrical outlet located within 2 ft.

(61 cm) of either side of the dryer. See Connecting

electric dryers.

• A sturdy floor to support the total dryer weight of 200

lbs (90.7 kg). The combined weight of a companion

appliance should also be considered.

• No other fuel-burning appliance can be installed in the

same closet as a dryer.

• Additional spacing should be considered for ease of

installation and servicing.

• Additional clearances might be required for wall, door

and floor moldings.

• Additional spacing should be considered on all sides

of the dryer to reduce noise transfer.

For closet installation, with a door, minimum

ventilation openings in the top and bottom of the

door are required. Louvered doors with equivalent

ventilation openings are acceptable.

• Companion appliance spacing should also be

considered.

NOTE

• A level floor with a maximum slope of 1 inch (2.5 cm) under entire dryer. If slope is greater than 1 inch (2.5 cm),

install the Extended Dryer Feet Kit. Clothes may not tumble properly, and automatic sensor cycles may not

operate correctly if dryer is not level.

• For a garage installation, you will need to place the dryer at least 18 inches (46 cm) above the floor. If using a

pedestal, you will need 18 inches (46 cm) to the bottom of the dryer.

NOTE

There should be at least a little space around the dryer (or any other appliance) to eliminate the transfer of

vibration from one to the other. Too much vibration, it could cause them to make noise or touch each other

causing paint damage and making even more noise.

INSTALLATION INSTRUCTIONS

30"

(76,1 cm)

5"**

(12,7 cm)

1"**

(2,5 cm)

1"

(2,5 cm)

1"

(2,5 cm)

27"

(68,6 cm)

9"**

(22,9 cm)

7"* (17,8 cm)

1"* (2,5 cm)

5

"**

(14 cm)

1/2

77

1/2

"

(196,8 cm)

3"* (7,6 cm)

6"*(15,2 cm)

3"* (7,6 cm)

27"

(68,6 cm)

1"

(2,5 cm)

1"

(2,5 cm)

24 in.

2*

(155 cm

2

)

48 in.

2*

(310 cm

2

)

5

"

**

(12.7 cm)

14

"

max.*

(35.6

cm)

50

1

⁄

4

"

(127.5 cm)

28

15

⁄

16

"

(73.4 cm)

21

1

⁄4

"

(54 cm)

45

7

⁄16

"

(115.3 cm)

Closet Door Vent

Requirements

5

"

**

(12,7 cm)

14

"

max.*

(35,6

cm)

50

1

⁄

4

"

(127,5 cm)

28

15

⁄16

"

(73,4 cm)

21

1

⁄4

"

(54 cm)

45

7

⁄16

"

(115,3 cm)

Requisitos de ventilación

de la puerta del armario

(2,54 cm) (2,54 cm)

(7,6 cm)

(7.6 cm)

(68,6 cm)

(2.54 cm) (2.54 cm)(68.6 cm)

28

(73.4 cm)

7"* (17.8 cm)

5"*

(12.7 cm)

1"*

(2.5 cm)

27

"

(68.6 cm)

1"

(2.54 cm)

1"

(2.54 cm)

28

(73,4 cm)

7"* (17,8 cm)

5"*

(12,7 cm)

1"*

(2,5 cm)

27

"

(68,6 cm)

1"

(2,54 cm)

1"

(2,54 cm)

5

"

**

(12,7 cm)

14

"

max.*

(35,6

cm)

50

1

⁄

4

"

(127,5 cm)

28

15

⁄

16

"

(73,4 cm)

21

1

⁄4

"

(54 cm)

45

7

⁄16

"

(115,3 cm)

Exigences d'aération de

la porte du placard

(2,54 cm) (2,54 cm)

(7,6 cm)

(68,6 cm)

MFL62512878_en_150603.indd 13 2015.6.3 3:43:21 PM

14

Clearances (cont.)

Recommended Installation Spacing For Cabinet Installation

• For cabinet installation with a door, minimum ventilation openings in the top of the cabinet are required.

*Required spacing

**For side or bottom venting,

2 inches (5.1 cm) spacing is allowed.

Leveling the Dryer

w

WARNING

• To reduce the risk of injury to persons, adhere to all

industry recommended safety procedures including

the use of long sleeved gloves and safety glasses.

Failure to follow this warning can cause serious injury

or death.

• The appliances are heavy. Two or more people are

required when installing the dryer. Failure to follow

this warning can cause serious injury or death.

To ensure that the dryer provides optimal drying

performance, it must be level. To minimize vibration,

noise, and unwanted movement, the floor must be a

perfectly level, solid surface.

1. Position the dryer in the final location. Place a level

across the top of the dryer.

• All four leveling feet must rest solidly on the floor.

Gently push on the top corners of the dryer to make

sure that the dryer does not rock from corner to corner.

If you are installing the dryer on the optional pedestal,

you must use the leveling feet on the pedestal to

level the dryer. The dryer leveling feet should be fully

retracted.

2. Use an adjustable wrench to turn the leveling feet.

Turn clockwise to raise the dryer or counterclockwise

to lower it. Raise or lower the leveling feet until dryer

is level from side to side and front to back.

Make sure that all 4 leveling feet are in firm contact with

the floor.

Level

Leveling Feet

NOTE

Adjust the leveling feet only as far as necessary to

level the dryer. Extending the leveling feet more than

necessary can cause the dryer to vibrate.

INSTALLATION INSTRUCTIONS

30"

(76,1 cm)

5"**

(12,7 cm)

1"**

(2,5 cm)

1"

(2,5 cm)

1"

(2,5 cm)

27"

(68,6 cm)

9"**

(22,9 cm)

7"* (17,8 cm)

1"* (2,5 cm)

5

"**

(14 cm)

1/2

77

1/2

"

(196,8 cm)

3"* (7,6 cm)

6"*(15,2 cm)

3"* (7,6 cm)

27"

(68,6 cm)

1"

(2,5 cm)

1"

(2,5 cm)

24 in.

2*

(155 cm

2

)

48 in.

2*

(310 cm

2

)

5

"

**

(12.7 cm)

14

"

max.*

(35.6

cm)

50

1

⁄

4

"

(127.5 cm)

28

15

⁄

16

"

(73.4 cm)

21

1

⁄4

"

(54 cm)

45

7

⁄16

"

(115.3 cm)

Closet Door Vent

Requirements

5

"

**

(12,7 cm)

14

"

max.*

(35,6

cm)

50

1

⁄

4

"

(127,5 cm)

28

15

⁄16

"

(73,4 cm)

21

1

⁄4

"

(54 cm)

45

7

⁄

16

"

(115,3 cm)

Requisitos de ventilación

de la puerta del armario

(2,54 cm) (2,54 cm)

(7,6 cm)

(7.6 cm)

(68,6 cm)

(2.54 cm) (2.54 cm)(68.6 cm)

28

(73.4 cm)

7"* (17.8 cm)

5"*

(12.7 cm)

1"*

(2.5 cm)

27

"

(68.6 cm)

1"

(2.54 cm)

1"

(2.54 cm)

28

(73,4 cm)

7"* (17,8 cm)

5"*

(12,7 cm)

1"*

(2,5 cm)

27

"

(68,6 cm)

1"

(2,54 cm)

1"

(2,54 cm)

5

"

**

(12,7 cm)

14

"

max.*

(35,6

cm)

50

1

⁄

4

"

(127,5 cm)

28

15

⁄16

"

(73,4 cm)

21

1

⁄4

"

(54 cm)

45

7

⁄16

"

(115,3 cm)

Exigences d'aération de

la porte du placard

(2,54 cm) (2,54 cm)

(7,6 cm)

(68,6 cm)

MFL62512878_en_150603.indd 14 2015.6.3 3:43:23 PM

15

ENGLISH

4. Remove the 4 screws securing the hinges to the door

frame. Remove the two plastic cover caps. Reinstall

the hinges and cover caps on the opposite sides from

which they were removed.

5. With the hinges and cover caps in the new locations,

remount the inner door frame onto the outer door

frame with the screws removed in step 3 above.

6. Reinstall the door with the screws from steps 1,2.

6. Test the swing of the door to make sure the hinges

and latch are properly aligned and that the door

closes and latches correctly.

w

WARNING

• To avoid damage to the dryer or the door, support

the door with a stool or box that fits under the

door, or have an assistant support the weight of the

door.

• Avoid dropping the door to avoid damage to the

door or the floor.

THE DRYER DOOR IS VERY LARGE AND HEAVY. Failure

to follow the instructions below can result in damage to

the dryer, property damage or injury to persons.

1. Open the door and remove the two plastic hole caps

on the catch side by gently prying up with a flat blade

screwdriver. Save these for step 6.

2. While supporting the door, remove the 4 screws, two

from each hinge. Set the door aside face down on a

protected surface to prevent damage to the door or

the work surface.

3. With the door on a protected surface, remove the 16

screws on each side of the door and lift off the inner

door frame using a flat blade screwdriver. Remove the

latch hook and blank and move them to the opposite

side.

Reversing the Door

Hole cap

Hinge screw

Inner door

frame

Latch hook

Hinge

assembly

Cover cap

Swing Door

INSTALLATION INSTRUCTIONS

MFL62512878_en_150603.indd 15 2015.6.3 3:43:51 PM

16

Installing the Side Vent Kit

w

WARNING

• Use a heavy metal vent.

• Do not use plastic or thin foil duct.

• Clean old ducts before installing this dryer.

• To reduce the risk of injury to persons, adhere to all

industry recommended safety procedures including

the use of long sleeved gloves and safety glasses.

• Failure to follow all of the safety warnings in this

manual could result in property damage, injury to

persons, or death.

Your new dryer is shipped to vent to the rear.

It can also be configured to vent to the bottom or side

(right-side venting is not available on gas models).

An adapter kit, part number 383EEL9001B, may be

purchased from your LG retailer. This kit contains the

necessary duct components to change the dryer vent

location.

1. Remove the rear exhaust duct retaining screw. Pull

out the exhaust duct.

Option 1: Side Venting

2. Press the tabs on the knockout and carefully remove

the knockout for the desired vent opening (right-

side venting is not available on gas models). Press the

adapter duct onto the blower housing and secure to

the base of the dryer as shown.

3. Preassemble a 4 inches (10.2 cm) elbow to the next

4-inches (10.2 cm) duct section, and secure all joints

with duct tape. Be sure that the male end of the elbow

faces AWAY from the dryer. Insert the elbow/duct

assembly through the side opening and press it onto

the adapter duct. Secure in place with duct tape.

Be sure that the male end of the duct protrudes 1½

inches (3.8 cm) to connect the remaining ductwork.

Attach cover plate to the back of the dryer with

included screw.

Option 2: Bottom Venting

2. Press the adapter duct onto the blower housing and

secure to the base of the dryer as shown.

3. Insert the 4 inches (10.2 cm) elbow through the rear

opening and press it onto the adapter duct. Be sure

that the male end of the elbow faces down through

hole in the bottom of the dryer. Secure in place with

duct tape.

Attach the cover plate to the back of the dryer with

included screw.

Rear

Exhaust Duct

Retaining

Screw

Elbow

Cover

Plate

Knockout

Bracket

Adapter

Duct

Bracket

Adapter

Duct

Elbow

Cover

Plate

1

1/2

”

(3.8 cm)

INSTALLATION INSTRUCTIONS

MFL62512878_en_150603.indd 16 2015.6.3 3:43:55 PM

17

ENGLISH

Venting the Dryer

w

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,

including the following:

• Do not crush or collapse ductwork. Failure to follow

these instructions can result in fire or death.

• Do not allow ductwork to rest on or contact sharp

objects. Failure to follow these instructions can result

in fire or death.

• If connecting to existing ductwork, make sure it

is suitable and clean before installing the dryer.

Failure to follow these instructions can result in fire or

death.

• Venting must conform to local building codes.

Failure to follow these instructions can result in fire or

death.

• Gas dryers MUST exhaust to the outdoors.

Failure to follow these instructions can result in fire or

death.

• Use only 4-inch (10.2 cm) rigid or flexible metal

ductwork inside the dryer cabinet and for venting

outside. Failure to follow these instructions can result

in fire or death.

• To reduce the risk of fire, combustion, or

accumulation of combustible gases, DO NOT

exhaust dryer air into an enclosed and unventilated

area, such as an attic, wall, ceiling, crawl space,

chimney, gas vent, or concealed space of a

building. Failure to follow these instructions can result

in fire or death.

• To reduce the risk of fire, DO NOT exhaust the dryer

with plastic or thin foil ducting.

Failure to follow these instructions can result in fire or

death.

• The exhaust duct must be 4 inches (10.2 cm) in

diameter with no obstructions. The exhaust duct

should be kept as short as possible. Make sure

to clean any old ducts before installing your new

dryer. Failure to follow these instructions can result in

fire or death.

• Rigid or semirigid metal ducting is recommended

for use between the dryer and the wall. In special

installations when it is impossible to make a

connection with the above recommendations, a

UL-listed flexible metal transition duct may be used

between the dryer and wall connection only. The

use of this ducting will affect drying time. Failure to

follow these instructions can result in fire or death.

• DO NOT use sheet metal screws or other fasteners

which extend into the duct that could catch lint and

reduce the efficiency of the exhaust system. Secure

all joints with duct tape. Failure to follow these

instructions can result in fire or death.

• To maximize operating results, please observe

the duct length limitations noted in the chart next

page. Failure to follow these instructions can result in

fire or death.

• Ductwork is not provided with the dryer. You

should obtain the necessary ductwork locally. The

end cap should have hinged dampers to prevent

backdraft when the dryer is not in use. Failure to

follow these instructions can result in fire or death.

• The total length of flexible metal duct shall not

exceed 8 ft. (2.4 m)

• In Canada, that only those foil-type flexible ducts,

if any, specifically identified for use with the

appliance by the manufacturer shall be used. In the

United States, that only those foil-type flexible ducts,

if any, specifically identified for use with the appliance

by the manufacturer and that comply with the Outline

for Clothes Dryer Transition Duct, Subject 2158A, shall

be used.

INSTALLATION INSTRUCTIONS

MFL62512878_en_150603.indd 17 2015.6.3 3:43:55 PM

18

Venting the Dryer (cont.)

Routing and Connecting Ductwork

Incorrect Venting

Correct Venting

NOTE

Deduct 6 ft. (1.8 m) for each additional elbow. It is not

recommended to use more than four 90° elbows.

NOTE

Follow the guidelines below to maximize drying

performance and reduce lint buildup and

condensation in the ductwork.

Ductwork and fittings are NOT included and must be

purchased separately.

• Use 4-inch (10.2 cm) diameter rigid or semirigid

metal ductwork.

• The exhaust duct run should be as short as possible.

• Use as few elbow joints as possible.

• The male end of each section of exhaust duct must

point away from the dryer.

• Use duct tape on all duct joints.

• Insulate ductwork that runs through unheated areas

in order to reduce condensation and lint buildup on

duct surfaces.

• Incorrect or inadequate exhaust systems are not

covered by the dryer warranty. Failures or poor

performance caused by such exhaust systems will

not be covered by the dryer warranty.

Ductwork

Wall Cap Type

0

1

2

3

4

0

1

2

3

4

Number Of

90° Elbows

Maximum Length Of

4-inch Diameter

Rigid Metal Duct

65 ft. (19.8 m)

55 ft. (16.8 m)

47 ft. (14.3 m)

36 ft. (11.0 m)

28 ft. (8.5 m)

55 ft. (16.8 m)

47 ft. (14.3 m )

41 ft. (12.5 m)

30 ft. (9.1 m)

22 ft. (6.7 m)

4"

(10.2 cm)

Recommended

Use only for

short run

installations

4"

(10.2 cm)

2

/4"

(6.35 cm)

INSTALLATION INSTRUCTIONS

MFL62512878_en_150603.indd 18 2015.6.3 3:43:57 PM

19

ENGLISH

Connecting Gas Dryers

w

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,

including the following:

Electrical requirements for gas models only

w

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,

including the following:

• Do not, under any circumstances, cut or remove the

third (ground) prong from the power cord. Failure

to follow this warning can result in fire, explosion, or

death.

• For personal safety, this dryer must be properly

grounded. Failure to follow this warning can result in

fire, explosion, or death.

• The power cord of this dryer is equipped with

a 3-prong (grounding) plug which mates with

a standard 3-prong (grounding) wall outlet to

minimize the possibility of electric shock hazard

from this appliance. Failure to follow this warning

can result in fire, explosion, or death.

• This dryer must be plugged into a 60 Hz, 120 VAC,

grounded outlet protected by a 15-ampere fuse

or circuit breaker. Failure to follow this warning can

result in fire, explosion, or death.

• Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility

and obligation to have it replaced with a properly

grounded 3-prong wall outlet. Failure to follow this

warning can result in fire, explosion, or death.

• Gas supply requirements:

As shipped from the factory, this dryer is

configured for use with natural gas. It can be

converted for use with LP (Liquefied Propane) gas.

Gas pressure must not exceed 13 inches of water

column.

• A qualified service or gas company technician must

connect the dryer to the gas service.

Failure to do so can result in fire, explosion, or death.

• Isolate the dryer from the gas supply system by

closing its individual manual shutoff valve during

any pressure testing of the gas supply. Failure to do

so can result in fire, explosion, or death.

• Supply line requirements:

Your laundry room must have a rigid gas

supply line to your dryer. In the United States,

an individual manual shutoff valve MUST be

installed within at least 6 ft. (1.8 m) of the dryer,

in accordance with the National Fuel Gas Code

ANSI Z223.1 or Canadian gas installation code CSA

B149.1. A

1

⁄₈ - inch NPT pipe plug must be installed.

Failure to do so can result in fire, explosion, death.

• If using a rigid pipe, the rigid pipe should be ½

- inch IPS. If acceptable under local codes and

ordinances and when acceptable to your gas

supplier,

3

⁄₈ - inch approved tubing may be used

where lengths are less than 20 ft. (6.1 m). Larger

tubing should be used for lengths in excess of 20 ft.

(6.1 m). Failure to do so can result in fire, explosion, or

death.

• Connect the dryer to the type of gas shown on

the nameplate. Failure to do so can result in fire,

explosion, or death.

• To prevent contamination of the gas valve,

purge the gas supply of air and sediment before

connecting the gas supply to the dryer. Before

tightening the connection between the gas supply

and the dryer, purge remaining air until the odor

of gas is detected. Failure to do so can result in fire,

explosion, or death.

• DO NOT use an open flame to inspect for gas leaks.

Use a noncorrosive leak-detection fluid. Failure to

do so can result in fire, explosion, or death.

• Use only a new AGA- or CSA-certified gas supply

line with flexible stainless steel connectors. Failure

to do so can result in fire, explosion, or death.

• Securely tighten all gas connections. Failure to do

so can result in fire, explosion, or death.

• DO NOT attempt any disassembly of the dryer;

any disassembly requires the attention and tools

of an authorized and qualified service person or

company. Failure to do so can result in fire, explosion,

or death.

• Use a pipe-joint compound that is insoluble in

Liquefied Petroleum (LP) gas on all pipe threads.

Failure to do so can result in fire, explosion, or death.

INSTALLATION INSTRUCTIONS

MFL62512878_en_150603.indd 19 2015.6.3 3:43:57 PM

20

Connecting Gas Dryers (cont.)

w

WARNING

To reduce the risk of fire, electric shock, or injury

to persons when using this appliance, follow basic

precautions, including the following:

• Installation and service must be performed by

a qualified installer, service agency, or the gas

supplier. Failure to do so can result in fire, explosion,

or death.

• Use only a new stainless steel flexible connector

and a new AGA-certified connector. Failure to do so

can result in fire, explosion, or death.

• A gas shutoff valve must be installed within 6 ft.

(1.8 m) of the dryer. Failure to do so can result in fire,

explosion, or death.

• The dryer is configured for Natural Gas when

shipped from the factory. Make sure that the dryer

is equipped with the correct burner orifice for the

type of gas being used (Natural Gas or Liquefied

Petroleum). Failure to do so can result in fire,

explosion, or death.

• If necessary, the correct orifice (For the LP orifice

kit, order part number 383EEL3002D) should be

installed by a qualified technician and the change

should be noted on the dryer. Failure to do so can

result in fire, explosion, or death.

• All connections must be in accordance with local

codes and regulations. Failure to do so can result in

fire, explosion, or death.

• Gas dryers MUST exhaust to the outdoors. Failure to

do so can result in fire, explosion, or death.

Connecting the gas supply

1. Make sure that the gas supply to the laundry room is

turned OFF. Confirm that the type of gas available in

your laundry room is appropriate for the dryer. The

dryer is prepared for Natural Gas with a

3

⁄₈ - inch NPT

gas connection.

2. Remove the shipping cap from the gas connection

at the back of the dryer. Be careful not to damage

the threads of the gas connector when removing the

shipping cap.

3. Connect the dryer to your laundry room’s gas supply

using a new flexible stainless steel connector with a

3

⁄₈

- inch NPT fitting.

4. Securely tighten all connections between the

dryer and your laundry room’s gas supply. Turn on

your laundry room’s gas supply and check all pipe

connections (both internal and external) for gas leaks

with a noncorrosive leak-detection fluid.

Electrical connection

High-altitude installations

The BTU rating of this dryer is AGA-certified for

elevations below 10,000 feet.

If your gas dryer is being installed at an elevation above

10,000 feet, it must be derated by a qualified technician

or gas supplier.

Plug dryer into a 120 VAC,

60 Hz grounded 3-prong

outlet.

Gas Supply

Shutoff Valve

3/8” NPT Gas

Connection

1/8” NPT Pipe

Plug

AGA/CSA-Certified

Stainless Steel Flexible

Connector

INSTALLATION INSTRUCTIONS

MFL62512878_en_150603.indd 20 2015.6.3 3:43:58 PM

La page charge ...

LG DLEX5175W Le manuel du propriétaire

Ce manuel convient également à

LG DLEX5175W Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents