KitchenAid KUIS15PRHB4 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KUIS15PRHB4

Catégorie: Fabricants de glaçons

Taper: Le manuel du propriétaire

Ce manuel convient également à

Kitchen_kid +

ICE MAKER

For questions about features, operation/performance, parts accessories or service, call: 1-800-422-1230

In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at...

www.kitchenaid.com or www.kitchenaid.com/canada

MACHINE A GLA( ONS

J: /_ !' +_; + . ; 1

(:+,I. _i)I++._:_.I o+._iI i7, [+9 _i)I]

Au Canada, pour assistance composez le 1-800-461-5681, pour installation ou service composez le 1-800-867-6777 ou visitez notre site web &...

www.kitchenaid.com/canada

Table of Contents/Table des matieres ............................................................................. 2

2217246

TABLE OF CONTENTS

ICE MAKER SAFETY .................................................................. 3

ICE MAKER INSTALLATION ......................................................... 4

Unpacking .................................................................................... 4

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 4

Leveling ........................................................................................ 5

Water Supply Connection ............................................................ 5

Reversing the Door Swing ........................................................... 7

Normal Sounds ............................................................................ 8

ICE MAKER USE ............................................................................ 8

How Your Ice Maker Works ......................................................... 8

Using the Controls ....................................................................... 9

ICE MAKER CARE .......................................................................... g

Cleaning ........................................................................................ 9

Changing the Light Bulb ............................................................ 11

Vacation and Moving Care ......................................................... 12

TROUBLESHOOTING .................................................................. 12

ASSISTANCE OR SERVICE ......................................................... 13

In the U.S.A ................................................................................ 13

In Canada ................................................................................... 13

WARRANTY .............................................................................. 14

TABLE DES MATIERES

S¢:CURIT¢ DE LA MACHINE A GLAQONS ............................. 15

INSTALLATION DE LA MACHINE A GLAQONS ........................ 16

Deballage .................................................................................... 16

Emplacement d'installation ........................................................ 16

Specifications electriques .......................................................... 16

Nivellement ................................................................................. 17

Raccordement a I'alimentation en eau ...................................... 17

Inversion du sens d'ouverture de la porte ................................. 19

Sons normaux ............................................................................ 20

UTILISATION DE LA MACHINE A GLAQONS ............................ 21

Fonctionnement de la machine a gla(_ons................................ 21

Utilisation des commandes ........................................................ 21

ENTRETIEN BE LA MACHINE ._,GLA(_ONS .............................. 21

Nettoyage ................................................................................... 21

Changement de I'ampoule d'eclairage ...................................... 24

Precautions a prendre pour les vacances

ou le demenagement .................................................................. 24

DCPANNAGE ................................................................................. 25

ASSISTANCE OU SERVICE ......................................................... 26

Aux letats-Unis ............................................................................ 26

Au Canada .................................................................................. 26

GARANTIE ................................................................................. 27

ICE MAKER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING." These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages willtell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before cleaning.

• Disconnect power before servicing.

• Replace all panels before operating.

• Use two or more people to move and install ice maker.

SAVE THESE INSTRUCTIONS

ICE MAKER

INSTALLATION

Excessive Weight Hazard

Use two or more people to move and install

ice maker.

Failure to do so can result in back or other injury.

Removing packaging materials

Remove tape and glue from your ice maker before using.

• To remove any remaining tape or glue, rub the area briskly

with your thumb. Tape or glue residue can also be easily

removed by rubbing a small amount of liquid dish soap over

the adhesive with your fingers. Wipe with warm water and

dry.

• Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your ice maker.

Cleaning before use

After you remove all of the packaging materials, clean the inside

of your ice maker before using it. See the cleaning instructions in

the "Ice Maker Care" section.

To ensure proper ventilation for your ice maker, the front side

must be completely unobstructed. The unit may be closed-in

on the top and three sides, but the installation should allow

the ice maker to be pulled forward for servicing if necessary.

Installation of the ice maker requires a cold water supply inlet

of 1/4in. (6.35 mm) OD soft copper tubing with a shut-off valve

and either a gravity-drain system or condensate pump to

carry the water to an existing drain.

Choose a well ventilated area with temperatures above 55°F

(13°C) and below 100°F (38°C). Best results are obtained

between 70°F (21°C) and 90°F (32°C). This unit MUST be

installed in an area protected from the elements, such as

wind, rain, water spray, or drip.

When installing the ice maker under a counter, follow the

recommended opening dimensions shown. Place electrical

and plumbing fixtures in the recommended location as

shown.

NOTE: Do not kink or pinch the power supply cord between

the ice maker and cabinet.

34"

(86.4 cm)

Min.

341/2"

(87.6 cm)

Max.

28112,,

(72.4 cm)

(38.1 crn)

1.Recommended Location for Electrical and Plumbing Fixtures.

2. Floor Level

You should choose a location where the floor is even. It is

important for the ice maker to be level in order to work

properly. If needed, you can adjust the height of the ice maker

by changing the position of the rear wheels. See the

"Leveling" section.

ElectricaJ Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can resuJt in

death, fire, or etectricaJ shock.

Before you move your ice maker into its final location, it is

important to make sure you have the proper electrical

connection:

A 115 Volt, 60 Hz., AC only 15 ampere electrical supply, properly

grounded in accordance with the National Electrical Code and

local codes and ordinances, is required.

It is recommended that a separate circuit, serving only your ice

maker, be provided. Use a receptacle which cannot be turned off

by a switch or pull chain.

Recommended grounding method

For your personal safety, this appliance must be grounded. This

appliance is equipped with a power supply cord having a 3 prong

grounding plug, To minimize possible shock hazard, the cord

must be plugged into a mating, 3 prong, grounding-type wall

receptacle, grounded in accordance with the National Electrical

Code and local codes and ordinances, If a mating wall receptacle

is not available, it is the personal responsibility of the customer to

have a properly grounded, 3 prong wall receptacle installed by a

qualified electrician.

It is important for the ice maker to be level in order to work

properly. Depending upon where you install the ice maker, you

may need to make several adjustments to level it.

Tools required

• Carpenter's level

• Adjustable wrench

• ¼in. sock_wrench

Undercounter installation

If you are installing the ice maker under a countertop, then you

may need to adjust the height of the ice maker. The adjustable

rear wheels are preset to position 1 for a cabinet opening height

of 34 in. (86.4 cm).

1. For cutout height of 34 in. (86.4 cm)

2. For cutout height of 34V8 in. (86.7 cm)

3. For cutout height of 34s/_Gin. (87.2 cm)

4. For cutout height of 34V2 in. (87.6 cm)

To adjust the rear wheel height

1. Using a 1/4in. socket wrench, remove the five screws from the

rear access panel and carefully pull the panel away from the

drain hose.

2. Using a % in. or adjustable wrench, remove the screw that

holds the rear wheel.

NOTE: Push up against the top back of the ice maker to take

some weight off of the wheels and make it easier to remove

the screws.

3. Move the rear wheel and screw to a new position as needed

for your cabinet opening height. Tighten the screw

completely.

4. Repeat Steps 2 and 3 to change the position of the wheel on

the other side.

5. Replace the rear panel and screws. Be sure that the drain

tube is positioned in the opening provided,

6. Use the front leveling legs to make sure the product is level.

To adjust the front leveling legs

Your ice maker has two adjustable leveling legs to help you

steady the product and make sure it is level.

NOTE: It is easier to adjust the leveling legs if you have another

person to assist you,

1. Place a carpenter's level on top of the product to see if the ice

maker is level from front to back and side to side.

2. Push up on the top front of the ice maker, and then locate the

leveling screws that are on the bottom front of the product.

3. Using an adjustable wrench, change the height of the legs as

follows:

• Turn the leveling leg to the right to lower that side of the

ice maker.

• Turn the leveling leg to the left to raise that side of the ice

maker.

NOTE: The ice maker should not wobble. Use shims to add

stability when needed.

Use a carpenter's level to re-check the ice maker to see that it

is even from front to back and side to side. If the ice maker is

not level, repeat Steps 2 and 3. If the ice maker is level, go to

the "Water Supply Connection" section.

Freestanding installation

If you are not installing your ice maker under a countertop, you

will probably not need to adjust the rear wheel height. Follow the

steps outlined in "To adjust the front leveling legs" earlier in this

section.

NOTE: The ice maker should not wobble, Use shims to add

stability when needed.

Read all directions carefully before you begin.

IMPORTANT:

• All installations must be in accordance with local plumbing

codes requirements.

• Use copper tubing and check for leaks.

• Install copper tubing only in areas where temperatures will

remain above freezing.

Tools required

• Standard screwdriver

• 7/16in. and 1/2in. open-end wrenches or two adjustable

wrenches

• ¼in. nut driver

• ¼in. drill bit

• Hand drill or electric drill properly grounded

NOTE: Your ice maker dealer has a kit available with a 1/4in.

(6.35 mm) saddle-type shut-off valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3_6in.

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

REAR VIEW

Connecting the water line

Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

Find a 1/2in. (12.70 mm) to 11/4in. (3.18 cm) vertical cold water

pipe near the ice maker.

NOTE: Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

3. Using a grounded drill, drill a 1/4in. (6.35 mm) hole in the cold

water pipe you have selected.

4. Fasten shut-off valve to cold water pipe with pipe clamp. Be

sure outlet end is solidly in the 1/4in. (6.35 mm) drilled hole in

the water pipe and that washer is under the pipe clamp.

Tighten packing nut. Tighten the pipe clamp screws carefully

and evenly so washer makes a watertight seal. Do not

overtighten the pipe clamp or you may crush cold water pipe

if it is soft copper tubing. Do not use a piercing-type or 3_6in.

(4.76 mm) saddle-type valve which reduces water flow and

clogs more easily.

5. Now you are ready to connect the copper tubing. Use 1/4in.

(6.35 mm) OD soft copper tubing for the cold water supply.

• Measure from the connection at the front of the ice maker

to the cold water pipe. Add 3 ft (91.4 cm) to ensure that

you have the proper length. This is the length of 1/4in.

(6.35 mm) OD soft copper tubing you need for the job. Be

sure both ends of the copper tubing are cut square.

• Slip compression sleeve and compression nut on copper

tubing as shown. Insert end of tubing into outlet end

squarely as far as it will go. Screw compression nut onto

outlet end with adjustable wrench. Do not overtighten.

8 ......... ...................2

......43 5

1.Cold WaterPipe 5. Compression Nut

2. Pipe Clamp 6. Compression Sleeve

3. Copper Tubing 7.Shut-Off Valve

4. Coupling (purchased) 8. Packing Nut

Place the free end of the tubing into a container or sink, and

turn on main water supply and flush out tubing until water is

clear. Turn off shut-off valve on the water pipe.

NOTE: Always drain the water line before making the final

connection to the inlet of the water valve to prevent possible

water valve malfunction.

Bend the copper tubing to meet the water line inlet which is

located on the back of the ice maker cabinet as shown.

!. Drain Hose (Drain Pump models only)

2. Vent Hose (Drain Pump models only)

3. Water Supply Line

Thread the nut onto the coupling on the end of the copper

tubing. Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

1 2

1.Line to ice maker

2. Nut (purchased)

4 3 2

3. Ferrule (purchased)

4. Coupling (purchased)

Remove the two screws in the lower access panel and the

two screws in the base grille area of the front panel support.

Pull forward to remove the lower access panel.

NOTE: To prevent rattling, be sure the copper tubing does not

touch the cabinet's side wall or other parts inside the cabinet.

FRONT VIEW

(14.5 cm)

1. Water Pan Drain

2. Water Valve

10. Turn shut-off valve ON.

11. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

12. Replace the lower access panel and screws.

Connecting the drain

Gravity drain system

Connect the ice maker drain to your drain in accordance with all

state and local codes and ordinances. Ifthe ice maker is

provided with a gravity drain system, follow these guidelines

when installing drain lines. This will prevent water from flowing

back into the ice maker storage bin and potentially flowing onto

the floor causing water damage.

• Drain lines must have a minimum of % in. (15.88 mm) inside

diameter.

Drain lines must have a 1in. drop per48 in. (2.54 cm drop per

122 cm) of run or 1/4in. drop per 12 in. (6.35 mm per

30.48 cm) and must not have low points where water can

settle.

The floor drains must be large enough to accommodate

drainage from all drains.

The ideal installation has a standpipe with a 11/2in. (3.81 cm)

to 2 in. (5.08 cm) PVC drain reducer installed directly below

the outlet of the drain tube as shown. You must maintain a

1 in. (2.54 cm) air gap between the drain pump hose and the

standpipe.

It may be desirable to insulate the drain line thoroughly up to

the drain inlet.

After ensuring that the drain system is adequate, follow these

steps to properly place the ice maker:

1. Plug in ice maker or reconnect power.

2. Re-check the ice maker to be sure that it is level. See the

"Leveling" section.

3. Push the ice maker into position so that the ice maker drain

tube is positioned over the PVC drain reducer.

SIDE VIEW

23"

(58.4 cm)

2" - 1 1/2,,

(5 cm - 3.8 cm)

(2.5cm)

1. Drain Hose

2. 1in. (2.54 cm) Air Gap

3. PVC Drain Reducer

4. Center of drain should be 23 in. (58.4 cm) from front of

door (with or without the 3/4in. (1.91 cm) panel on the door).

4. If it is required by your local sanitation code, seal the cabinet

to the floor with an approved caulking compound after all

water and electrical connections have been made.

Drain pump system (on some models}

Connect the drain pump hose (provided with the product) to your

drain in accordance with all state and local codes and

ordinances.

NOTE: If the drain hose becomes twisted and water cannot

drain, your ice maker will not work.

TOOLS NEEDED: %6 in. wrench, 1/4in. wrench, flat putty knife,

Phillips screwdriver

Hinge Pin

5/16in. Hex Head Hinge Screw

Handle Screw

Endcap Screw

To remove door from hinges:

1. Unplug ice maker or disconnect power.

2. Remove the handle screws and handle (on some models).

Keep the parts together and set them aside.

3. Remove the hinge pin from the top hinge.

4. Remove the door from the hinges and screw the top hinge pin

back into the top hinge.

5. Reverse the door endcaps as follows:

• Remove both the screws and endcaps (top and bottom).

• Place the top endcap on the bottom of the opposite side

of the door with the long flat side facing the door front.

• Place the bottom endcap on the top of the opposite side

of the door with the long flat side facing the door front.

6. Set the door aside.

To reverse the hinges:

1. Unscrew and remove the top hinge. Replace the screws in

the empty hinge holes.

2. Remove the screws from the bottom of the opposite side of

the ice maker cabinet. Turn the top hinge upside down so that

the hinge pin points up. Place the hinge on the bottom

opposite side of the ice maker and tighten screws.

3. Remove the plastic hinge pin sleeve from the "old" bottom

hinge and replace it on the new bottom hinge pin.

4. Remove the "old" bottom hinge screws and hinge. Replace

the screws in the empty hinge holes.

5. Remove the screws from the top of the opposite side of the

ice maker cabinet. Turn the hinge upside down so that the

hinge pin points down. Place the hinge on the top opposite

side of the ice maker and tighten the screws.

6. Remove the top hinge pin.

To replace door on hinges:

1. Place plastic hinge pin sleeve in the top hinge hole on the

door. Align the door with the top hinge hole and replace the

top hinge pin.

2. Replace the handle and handle screws.

TopHinge

1.Hinge Pin

2. Hinge Pin Sleeve

Bottom Hinge

.....................................

3. Hinge

4. Hex-Head Hinge Screw

...................................................4

1.Hex-Head Hinge Screw 3. Hinge

2. Hinge Pin Sleeve 4. Hinge Pin

To reverse the door catch:

1. Remove the hole plugs from the opposite side of the door

and set aside.

2. Remove the screws from the magnetic door catch and

replace it on the opposite side of the door.

3. Push the hole plugs into place on the opposite side of the

door.

4. Plug in ice maker or reconnect power.

Your new ice maker may make sounds that are not familiar to

you. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard

surfaces like the floor, walls and cabinets can make the sounds

seem louder than they actually are. The following describes the

kinds of sounds that might be new to you and what may be

making them.

• You will hear a buzzing sound when the water valve opens to

fill the water reservoir for each cycle.

Rattling noises may come from the flow of the refrigerant or

the water line. Items stored on top of the ice maker can also

make noises.

The high efficiency compressor may make a pulsating or high

pitched sound.

Water running over the evaporator plate may make a

splashing sound.

Water running from the evaporator plate to the water reservoir

may make a splashing sound.

As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your ice maker.

You may hear air being forced over the condenser by the

condenser fan.

During the harvest cycle, you may hear a "thud" when the ice

sheet slides from the evaporator onto the cutter grid.

When you first start the ice maker, you may hear water

running continuously. The ice maker is programmed to run a

rinse cycle before it begins to make ice.

ICE MAKER USE

_,_,,_"_ _'_," __ _ 's_ ,_s¸-°_As¸¸_ _'_

When you first start your ice maker, the water pan will fill and the

system will rinse itself before starting to make ice. The rinsing

process takes about five minutes.

Under normal operating conditions, the ice maker will cycle at

preset temperatures. The ice level sensor located in the ice

storage bin will monitor the ice levels.

IMPORTANT:

• If the water supply to the ice maker is turned off, be sure to

set the ice maker control to OFR

• The ice maker is designed to make clear ice from the majority

of water sources on a daily basis. If your results are

unsatisfactory, your water may need to be filtered or treated.

The Ice Making Process

1. Water is constantly circulated over afreezing plate. As the

water freezes into ice, the minerals in the water are rejected.

This produces a clear sheet of ice with a low mineral content.

2. When the desired thickness is reached, the ice sheet is

released and slides onto a cutter grid. The grid divides the

sheet into individual cubes.

3. The water containing the rejected minerals is drained after

each freezing cycle.

4. Fresh water enters the machine for the next ice making cycle.

5. Cubes fall into the storage bin. When the bin is full, the ice

maker shuts off automatically and restarts when more ice is

needed. The ice bin is not refrigerated and some melting will

occur. The amount of melting varies with room temperature.

NOTE: As the room and water temperatures vary, so will the

amount of ice produced and stored. This means that higher

operating temperatures result in reduced ice production.

1. To start the normal ice making cycle, select ON.

2. To stop ice maker operation, select OFR

CLEANING

NOTE: The CLEAN setting is used whenever solutions are

circulated through the ice maker for cleaning. Only the water

pump and compressor operate at this setting. See the "Cleaning"

section.

ICE MAKER CARE

The ice making system and the air cooled condenser need to be

cleaned regularly for the ice maker to operate at peak efficiency

and to prevent premature failure of system components. See the

"Ice Maker System" and the "Condenser" sections.

Exterior Surfaces

Wash the exterior enamel surfaces and gaskets with warm water

and mild soap or detergent. Wipe and dry. Regular use of a good

household appliance cleaner and wax will help protect the finish.

Do not use abrasive cleaners on enamel surfaces as they may

scratch the finish.

For products with a stainless steel exterior, use a clean sponge or

soft cloth and a mild detergent in warm water. Do not use

abrasive or harsh cleaners.

Ice Maker System

Minerals that are removed from water during the freezing cycle

will eventually form a hard scaly deposit in the water system.

Cleaning the system regularly helps remove the mineral scale

buildup. How often you need to clean the system depends upon

how hard your water is. With hard water of 15 to 20 grains/gal. (4

to 5 grains/liter), you may need to clean the system as often as

every 6 months.

NOTE: Use one 16 oz (473 mL) bottle of NU-CALGON* Nickel

Safe Ice Machine Cleaner. To order, call 1-800-442-9991 and ask

for Part Number 8171307. In Canada, call 1-800-807-6777.

1. Push the selector switch to OFF.

2. Wait 5 to 10 minutes for the ice to fall into the storage bin.

Remove all ice from the storage bin.

3. Unscrew the drain cap from the bottom of the water pan

located inside the storage bin as shown. Allow the water to

drain completely.

4. Replace the drain cap securely on the water pan. If the drain

cap is loose, water will empty from the water pan and you will

have either thin ice or no ice.

5. Read and follow all handling information on the cleaner bottle

before completing the steps below. Use one 16 oz (473 mL)

bottle of NU-CALGON* Nickel Safe Ice Machine Cleaner.

*Nu-Calgon is a trademark of Calgon Corporation.

6. Pouronebottleofsolutionintothewaterpan.Fillthebottle

twicewithtapwaterandpouritintothewaterpan.

1. Water Pan

2. Drain Cap

7. Push the selector switch to CLEAN. (See the "Using the

Controls" section.) The light will turn on, indicating that the

cleaning cycle is in process. When the indicator light turns off

(approximately 45 minutes), the cleaning cycle is complete.

During the cleaning cycle, the system will both clean and

rinse itself.

8. After the cleaning cycle is complete, remove the drain cap

from the water pan to see if any cleaning solution is left in the

water pan. If cleaning solution drains from the water pan, you

should run the clean cycle again. Be sure to replace the drain

cap securely on the water pan. Ifthe drain cap is loose, water

will empty from the water pan and you will have either thin ice

or no ice.

NOTE: Severe scale buildup may require repeated cleaning with

a fresh quantity of cleaning solution.

9. Push the selector switch to ON to resume ice production.

Condenser

A dirty or clogged condenser:

• Prevents proper airflow.

• Reduces ice making capacity.

• Causes higher than recommended operating temperatures

which may lead to component failure.

EJectrical Shock Hazard

Disconnect power before cJeaning.

Replace all panels before operating.

Failure to do so can result in death or

etectricaJ shock.

1. Unplug ice maker or disconnect power.

2. Remove the two screws in the lower access panel and the

two screws from the base grille area of the front panel

support. Pull forward to remove the lower access panel.

3. Pull the bottom forward and then pull down to remove the

lower access panel.

1. Lower Access Panel Screws

2. Base Grille Screws

Remove dirt and lint from the condenser fins and the unit

compartment with a brush attachment on a vacuum cleaner.

5. Replace the lower access panel using the four screws.

6. Plug in ice maker or reconnect power.

Interior Components

1. Unplug ice maker or disconnect power.

2. Open the storage bin door and remove any ice that is in the

bin.

3. Remove the drain cap from the water pan and drain

thoroughly. Replace the drain cap securely on the water pan.

If the drain cap is loose, water will empty from the water pan,

and you will have either thin ice or no ice.

4. Remove the three screws that hold the cutter grid cover in

place.

Unplug the wiring harness from the left side of the cutter grid.

1. Cutter Grid Cover

2. Screws

6. Unplug the ice level sensor from the right side of the cutter

grid. Pull the ice level sensor down and forward away from

the cutter grid.

7. Remove the right-hand and left-hand screws. Lift the cutter

grid up and out.

NOTE: Make sure the plastic spacer from the right-hand side

of the cutter grid bracket stays with the cutter grid.

1.Cutter Grid Harness 4. Ice Level SensorHarness

2. Screw 5. Plastic Spacer

3. Cutter Grid 6. Screw

Remove the two thumb screws that hold the water pan in

place. Push down with one hand on the front of the pan while

pulling forward on the bottom back side.

T° \ J

J J- •.........

.......... 1

• •3

1. Water Pan

2. Water Pan Thumb Screws

3. Drain Cap

Remove, clean and replace the ice scoop and ice scoop

holder.

• After removing the ice scoop, remove the holder by lifting

the front free from the cutter grid cover. Then lift the back

of the holder slightly to release the rear hook and pull

forward.

• Wash the ice scoop holder along with the other interior

components using the following instructions.

Replace the ice scoop holder by aligning the rear hook

with the opening (the holder angles down slightly). Slide

the holder back fully until the front rests securely on the

cutter grid cover.

10.

!. Ice Scoop Holder

Wash the interior components (cutter grid, exterior of hoses,

and water pan) and the storage bin, door gasket, ice scoop,

and ice scoop holder with mild soap or detergent and warm

water. Rinse in clean water. Then clean the same parts with a

solution of 1 tablespoon (15 mL) of household bleach in 1

gallon (3.8 L) warm water. Rinse again thoroughly in clean

water.

NOTE: Do not remove hoses. Do not wash plastic parts in

dishwasher. They cannot withstand temperatures above

145°F (63°0).

11. Replace water pan by pushing back on the bottom with one

hand while pushing up and back on the top. Secure the water

pan by replacing both screws.

12. Check the following:

• Drain cap from the water pan is securely in place. If the

drain cap is loose, water will empty from the water pan,

and you will have either thin ice or no ice.

• Hose from water pan is inserted into storage bin drain

opening.

13. Slide the cutter grid back into place and secure it by

replacing the right-hand screw and plastic spacer. Then

tighten the left-hand screw. Reconnect the cutter grid

harness and the ice level sensor harness.

14. Plug in ice maker or reconnect power.

The ice maker has a light bulb in the top of the storage bin. To

replace it, open the bin door and follow these instructions:

1. Unplug ice maker or disconnect powe£

2. Remove the three screws that hold the cutter grid cover in

place. Reach behind the control panel and pull the light bulb

down from the ceiling.

3. Replace with a 12-volt wedge base-type bulb (automotive

#917). Locate the light bulb receptacle in the ceiling behind

the control panel. Align the flat edge of the light bulb with the

receptacle and snap the bulb into place.

4. Replace the cutter grid cover with three screws.

5. Plug in ice maker or reconnect power.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all paneJs before operating.

Failure to do so can result in death or

eJectricaJ shock.

To shut down the ice maker:

1. Unplug ice maker or disconnect power.

2. Remove all ice from storage bin.

3. Shut off the water supply,

4. Remove the two screws in the lower access panel and the

two screws from the base grille area of the front panel

support. Pull forward to remove the lower access panel.

5. Disconnect the inlet and outlet lines to water valve. Allow

these lines to drain and then reconnect to the valve.

6. Replace lower access panel and screws.

7. Drain water from water pan by removing the drain cap,

8. If the room temperature will drop below 32°F (0°C), remove

water from the drain line,

For ice makers with a drain pump installed:

• Plug in ice maker or reconnect power.

• Turn ice maker off and remove all remaining ice from ice

bin.

• Pour 1 quart (0.95 L) of water into the ice bin near the

drain and let the unit stand for approximately five

minutes, This will allow the water in the bin to drain into

the drain pump so that the pump will remove the

remaining water from the ice bin and the drain pump,

• Unplug ice maker or disconnect power.

9. Before using again, clean the ice maker and storage bin.

10. Plug into a grounded 3 prong outlet.

NOTE: All components of the ice maker are permanently

lubricated at the factory. They should not require any additional

oiling throughout the normal life of the machine.

TROUBLESHOOTING

Trythe solutions suggested here first in order to avoid the

cost of an unnecessary service call.

Unit does not run

• Is the control set to ON? Be sure that the control is set to

ON.

• Is the power cord plugged in? Plug into a grounded 3 prong

outlet.

• Has a household fuse or circuit breaker tripped? Replace

the fuse or reset the circuit.

Is the room temperature cooler than normal? Room

temperature must be above 55°F (13°C). Otherwise, bin

thermostat may sense cold room temperature and shut off

even though bin is not full of ice. Also, unit may not restart

once it does shut off.

Unit runs but produces no ice

• Is the control set to ON? Be sure that the control is set to

ON.

• Is the water supply connected? Make sure the water supply

is properly connected and turned on.

Unit runs but produces very little ice

• Is the room temperature hotter than normal? Room

temperatures of more than 90°F (32°C) will normally reduce

ice production.

• Is the condenser dirty? Dirt or lint may be blocking the

airflow through the condenser. See the "Condenser" section.

• Is there scale buildup in the ice maker? If there is white

scale buildup in the ice maker's water or freezing system, you

should clean the ice maker. See the "Ice Maker System" and

the "Interior Components" sections.

• Is the drain cap securely in place? Tighten the drain cap if it

is loose. If the drain cap is loose, water will empty from the

water pan, and you will have either thin ice or no ice.

Grid is not cutting ice sheets

Is the cutter grid securely in place? Unplug the ice maker

or disconnect power. Remove the cutter grid cover and check

the cutter grid harness plug to make sure the connection is

secure,

Taste in ice cubes

• Is there unusually high mineral content in the water

supply? The water may need to be filtered or treated,

Are there food items stored in the ice bin? Do not store any

foods in the ice bin.

Were all the packaging materials removed? Make sure that

all packaging materials were removed at the time of

installation.

ASSISTANCE

OR SERVICE

Before calling for assistance or service, please check

"Troubleshooting." It may save you the cost of a service call. If

you still need help, follow the instructions below.

When calling, please know the purchase date and the complete

model and serial number of your appliance. This information will

help us to better respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

only use factory specified replacement parts. Factory specified

replacement parts will fit right and work right because they are

made with the same precision used to build every new

KITCH ENAID_ appliance.

To locate factory specified replacement parts in your area, call

our Customer Interaction Center telephone number or your

nearest designated service center.

Call the KitchenAid Customer Interaction Center

toll free: 1-800-422-1230.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Installation information.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

• Referrals to local dealers, repair parts distributors, and

service companies. KitchenAid designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in the United States.

To locate the KitchenAid designated service company in your

area, you can also look in your telephone directory Yellow

Pages.

For further assistance

If you need further assistance, you can write to KitchenAid with

any questions or concerns at:

KitchenAid Brand Home Appliances

Customer Interaction Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

Call the KitchenAid Canada Customer Interaction Center toll free:

1-800-461-5681 8:30 a.m. - 5:30 p.m. (EST).

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Referrals to local dealers.

For service in Canada

Call 1-800-807-6777. KitchenAid Canada designated service

technicians are trained to fulfill the product warranty and provide

after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to KitchenAid

Canada with any questions or concerns at:

Customer Interaction Center

KitchenAid Canada

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

KITCHENAID ®ICE MAKER WARRANTY

ONE-YEAR FULL WARRANTY ON ICE MAKER

For one year from the date of purchase when this product is operated in a residential or light commercial setting, and is maintained

according to the instructions furnished with the product, KitchenAid will pay for factory specified replacement parts and repair labor to

correct defects in materials or workmanship. Service must be provided by a KitchenAid designated service company.

SECOND THROUGH FIFrH YEAR FULL WARRANTY SEALED REFRIGERATION SYSTEM PARTS AS LISTED

In second through fifth years from the date of purchase, KitchenAid will pay for replacement parts and repair labor costs to correct

defects in materials or workmanship in the sealed refrigeration system. These parts are compressor, evaporator, condenser, dryer/

strainer, and connecting tubing. Service must be performed by a KitchenAid designated service company.

KitchenAid will not pay for:

1. Service calls to correct the installation of your ice maker, to instruct you how to use your ice maker, to replace house fuses or correct

house wiring or plumbing, to replace light bulbs.

2. Repairs when your ice maker is used in locations where usage exceeds ice making capabilities of unit (about 50 pounds in 24

hours). This ice maker is intended only for residential and/or light commercial use that does not exceed these capabilities.

3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, or installation not in

accordance with local electrical or plumbing codes, or use of product not approved by KitchenAid.

4. Replacement parts or repair labor costs for units operated outside the United States and Canada.

5. Pickup and delivery. This product is designed to be repaired in the home.

6. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

7. In Canada, travel or transportation expenses for customers who reside in remote areas.

KITCHENAID AND KITCHENAID CANADA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or

limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state

to state, province to province.

Outside the 50 United States and Canada, this warranty does not apply. Contact your local KitchenAid dealer to determine if

another warranty applies.

If you need service, first see the "Troubleshooting" section of this book. After checking "Troubleshooting," additional help can be found

by checking the "Assistance or Service" section or by calling the KitchenAid Customer Interaction Center, 1-800-422-1230 (toll-free),

from anywhere in the U.S.A. For service in Canada, call 1-800-807-6777. 4/00

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or

installation date for in-warranty service.

Write down the following information about your ice maker to

better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label, located on the inside left wall of the ice maker.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

SECURITE DE LA MACHINE A GLA( ONS

Votre s6curit6 et celle des autres est tr_s importante.

Nous donnons de nombreux messages de securit6 importants dans ce manuel et sur votre appareil menager.

Assurez-vous de toujours lire tousles messages de securit6 et de vous y conformer.

_ oici le symbole d'alerte de securit&

Ce symbole d'alerte de securit6 vous signale les dangers potentiels de deces et de blessures graves

& vous et & d'autres.

Tousles messages de securit6 suivront le symbole d'alerte de securit6 et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient :

Risque possible de d_c_s ou de blessure grave si

vous ne suivez pas imm_diatement les instructions.

Risque possible de d_c_s ou de blessure grave

si vous ne suivez pas les instructions.

Tousles messages de securit6 vous diront quel est le danger potentiel et vous disent comment reduire le risque de

blessure et ce qui peut se produire en cas de non-respect des instructions.

IMPORTANTES iNSTRUCTiONS DE SECURITE

AVERTUSSEMENT : Pour r_duire le risque dqncendie, de choc 61ectrique ou de blessures Iors de I'utiiisation

de la machine & glagons, it convient d'observer certaines precautions 616mentaJres:

Brancher sur une prise a 3 alv&oles retiee a la terre.

B Ne pas enlever la broche de liaison a la terre.

Ne pas utiliser un adaptateur.

Ne pas utiJiser un c_bte de ra!longe.

Utiliser deux ou plus de personnes pour deplacer et

installer la machine a glaqons.

D6connecter la source de courant electrique avant le

nettoyage.

Deconnecter la source de courant &lectdque avant

I'entretien.

Replacer tous les panneaux avant de faire la remise

en marche.

CONSERVEZ CES iNSTRUCTiONS

'_' REMARQUE : II ne faut pas ecraser ni pincer le cordon

d'alimentation electrique entre I'appareil et I'armoire.

INSTALLATION DE LA

MACHINE A GLA( ONS

Risque du poids excessif

Utiliser deux ou plus de personnes pour d_placer

et installer la machine _ gla£ons.

Le non-respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

34"

(86,4 era)

Min.

341/2,,

(87,6 era)

Max.

28112 "

(72,4 cm)

Enl_vement des mat6riaux d'emballage

Enlever le ruban adhesif et la colle de ia machine a gla(_ons avant

de I'utiliser.

Pour enlever ce qui reste du ruban adhesif ou de la colle,

frotter la surface vivement avec le pouce. La colle ou I'adhesif

qui reste peut _tre facilement enlevee par frottage avec les

doigts et une petite quantite de savon liquide pour ia vaisseiie

sur I'adhesif. Rincer a i'eau tiede et essuyer.

Ne pas utiliser d'instruments ac@es, d'alcool a friction, de

liquides inflammables ou de nettoyants abrasifs pour enlever

le ruban adhesif ou la colle. Ces produits peuvent

endommager la surface de votre machine a glat_ons.

Nettoyage avant I'utilisation

Apres avoir enleve tousles materiaux d'emballage, nettoyer

I'interieur de la machine & gla(_ons avant de I'utiliser. Voir les

instructions de nettoyage dans la section "Entretien de la

machine & glagons".

Pour assurer une bonne a@ation de votre appareil, I'avant

dolt @re completement d_gag& Les autres c6tes et le dessus

de I'appareil peuvent 6tre dissimules, mais I'installation dolt

permettre de tirer la machine a glagons vers I'avant pour y

faire les travaux d'entretien requis.

Pour installer la machine a gla(_ons, il faut avoir un tuyau

d'alimentation en eau froide de V4po (6,35 mm) de dia. ext.

en cuivre mou avec un robinet et un systeme de vidange par

gravite ou une pompe a condensat pour pousser I'eau vers

un drain existant.

• Choisir un endroit bien aere ou la temperature est superieure

55°F (13°C) et inferieure a 100°F (38°C). Pour tirer le

meilleur rendement de I'appareil, la temperature ambiante

dolt se situer entre 70°F (21°C) et 90°F (32°C). Cet appareil

DOlT _tre installe a un endroit protege contre les elements,

comme le vent, la pluie, les embruns ou les egouttures.

• Lorsque I'appareil est installe sous un comptoir, observer les

dimensions d'ouverture recommandees. Placer ies

composants electriques et de piomberie dans ia zone

recommandee a i'illustration.

1.Zone recommand6e

et de plomberie

2. Niveau du plancher

(38,1cm)

_our /es cornposants 61ectriques

II est recommande de choisir un emplacement ou le plancher

est uniforme. II est important que la machine a gla(_ons soit

d'aplomb pour bien fonctionner. Au besoin, il est possible de

regler la hauteur de la machine a gla(_ons en changeant la

position des roulettes arriere. Voir la section "Nivellement".

Risque de choc e_ectrique

Bra_cher sur une prise a 3 a_veo_es retiee

Ja terre.

Ne pas entever Ja broche de liaison a Ja terre.

Ne pas utitiser un adaptateur.

Ne pas utitiser un c_bJe de raHonge.

Le no_-respect de ces instructions peut causer

un deces, un incendie ou un choc etectrique.

Avant de pousser la machine a glagons a sa place definitive, il

faut s'assurer que le raccordement electrique a ete bien fait.

IIfaut un circuit d'alimentation electrique CA de 115 volts, 60 Hz,

de seulement 15 amperes mis a la terre conformement aux

instructions du Code national de i'eiectricit& et des codes et

reglements Iocaux.

II est recommande de reserver un circuit special & la machine

glagons. Utiliser une bofte ou I'alimentation ne peut pas _tre

coupee a I'aide d'un interrupteur ou d'une cha_nette.

M_thode de mise & la terre recommand_e

Pour votre propre securite, cet appareil dolt 6tre mis a la terre.

L'appareil comporte un cordon d'alimentation electrique & trois

broches pour la mise a la terre. Pour minimiser les risques de

choc electrique, le cordon d'alimentation electrique dolt _tre

branche sur une prise de courant murale raise a la terre

correspondante a trois alveoles ou la raise & la terre a ete faite

conformement au Code national de I'electricite et aux codes et

reglements Iocaux. S'il n'y a pas de prise de courant

correspondante, il incombe au client de faire installer une prise

de courant murale a trois alveoles mise a la terre de fagon

appropriee par un electricien qualifie.

IIest important que la machine a glagons soit d'aplomb pour bien

fonctionner. Selon I'endroit ou vous installez la machine

gla(_ons, vous pourrez avoir a effectuer plusieurs ajustements

pour la mettre d'aplomb.

Outillage requis

• Niveau

• Cle& molette

• Cle a douille de 1/4po

Installation sous un comptoir

Si vous installez la machine & glagons sous un comptoir, il vous

faudra peut-_tre ajuster la hauteur de la machine. Les roulettes

arriere reglables sont prer6gl6es a la position 1 pour une

ouverture de 34 po (86,4 cm) de hauteur.

_' ¸.¸¸%

2 • i¸¸¸¸¸¸

1.Pour unehauteur d'encastrement de 34po (86,4cm)

2. Pour unehauteur d'encastrement de 34 V8po (86,7cm)

3. Pour unehauteur d'encastrement de 345Aepo (87,2 cm)

4. Pour une hauteur d'encastrement de 34 V2po (87,6cm)

R_glage de la hauteur des roulettes arri_re

1. Au moyen d'une cle a douille de 1/,po, enlever les cinq vis du

panneau d'acces arriere et retirer soigneusement le panneau

en I'eloignant du tuyau d'evacuation.

2. Au moyen d'une cle de 3/8po ou a molette, 6ter la vis qui

retient la roulette arriere.

REMARQUE : Pousser sur la partie arriere superieure de la

machine a glagons pour reduire une pattie du poids sur les

roulettes arriere. II est ainsi plus facile d'enlever les vis,

3. Deplacer la roulette arriere et la vis & une nouvelle position en

fonction de la hauteur d'encastrement necessaire, Serrer la

vis completement.

4. Rep6ter les etapes 2 et 3 pour changer la position de la

roulette de I'autre c6te.

5. Reinstaller le panneau arriere et les vis. S'assurer que le tuyau

d'evacuation se trouve dans I'ouverture fournie.

6. Utiliser les pieds de nivellement avant pour vous assurer que

le produit est d'aplomb.

Ajustement des pieds de nivellement avant

La machine a glagons comporte 2 pieds de nivellement reglables

pour vous aider a stabiliser le produit eta vous assurer qu'il est

d'aplomb.

REMARQUE : IIest plus facile d'ajuster les pieds de nivellement

si on se fait aider par une autre personne,

1. Placer un niveau sur le dessus du produit pour voir si la

machine a gla(?ons est d'aplomb d'avant en arriere et

transversalement.

2. Pousser vers le haut sur la pattie avant de la machine

glagons pour reperer les vis de nivellement qui se trouvent au

has a I'avant du produit.

3. Au moyen d'une cle a molette, modifier la hauteur des pieds

comme suit :

• Tourner le pied de nivellement vers la droite pour abaisser

ce c6te de la machine a glagons.

• Tourner le pied de nivellement vers la gauche pour

soulever ce c6te de la machine a glagons.

REMARQUE : La machine a glagons ne devrait pas osciller.

Utiliser des cales pour accroltre la stabilite au besoin,

Utiliser un niveau pour reverifier que la machine a gla9ons est

d'aplomb d'avant en arriere et transversalement. Si elle n'est

pas d'aplomb, r_peter les etapes 2 et 3. Si la machine est

d'aplomb, passer a la section "Raccordement aI'alimentation

en eau".

Installation autoportante

Si vous n'installez pas la machine a glagons dans un

encastrement, il ne sera probablement pas necessaire d'ajuster

la hauteur des roulettes arriere. Suivre les etapes decrites

"Ajustement des pieds de nivellement avant" plus haut dans

cette section.

REMARQUE : La machine &glagons ne devrait pas osciller.

Utiliser des cales pour accroitre la stabilite au besoin.

Lire toutes les instructions avec soin avant de commencer.

IMPORTANT :

• Toutes les installations doivent respecter les codes Iocaux de

plomberie.

• Utiliser un tuyau en cuivre et verifier s'il y a des fuites.

• Installer seulement les tuyaux en cuivre la ou les

temperatures resteront au-dessus du point de congelation.

Outils requis

• Tournevis ordinaire

• Cles ouvertes de _A8poet de 1/_po ou deux cles a molette

• Tourne-ecrou de 1/4po

• Meche perceuse de 1/,po

• Perceuse manuelle ou electrique convenablement raise a la

terre

REMARQUE : Votre marchand de machine a glagons a une

trousse de robinet d'arr_t a etrier de 1/,po (6,35 ram), un raccord-

union et tuyau en cuivre. Avant de faire un achat, s'assurer que le

robinet d'arr_t a etrier respecte les codes Iocaux de plomberie,

Ne pas utiliser de robinet d'arr_t a etrier perforant ou de 3/18po

(4,76 mm) qui reduit le debit d'eau et qui se bouche plus

facilement.

Raccordement du tuyau d'eau

Couper I'alimentation principale en eau. Ouvrir le robinet le

plus proche assez Iongtemps pour vider I'eau du tuyau.

Trouver un tuyau vertical d'alimentation en eau froide de 1/2po

(12,70 mm) a 11/4po (3,18 cm) a proximite de la machine

glagons.

REMARQUE : Un conduit horizontal fonctionnera, mais on

doit observer le procede suivant : Percer par le dessus de la

canalisation et non pas par le dessous. Ainsi, I'eau ne

risquera pas d'arroser la perceuse. Ceci emp_che egalement

les sediments qu'on trouve normalement dans I'eau de

s'accumuler dans le robinet d'arr_t.

3. /_,I'aide d'une perceuse electrique reliee a la terre, percer un

trou de 1Apo (6,35 mm) dans le tuyau d'alimentation en eau

froide que vous avez choisi.

4. Fixer le robinet d'arr_t sur le tuyau d'alimentation en eau

I'aide d'une bride pour tuyau. IIfaut s'assurer que I'extremite

de sortie est bien inseree dans le trou de 1Apo (6,35 mm)

perce dans le tuyau en eau et que la rondelle est placee sous

la bride du tuyau. Serrer I'ecrou de garniture. Serrer

soigneusement et uniformement les vis fixant la bride de

tuyau sur le tuyau afin que la rondelle forme un scellement 8.

etanche. Ne pas serrer la bride du tuyau a I'exces sans quoi

le tuyau d'alimentation en eau froide pourrait _tre ecrase s'il

s'agit d'un tuyau en cuivre mou. Ne pas utiliser un robinet

d'arr_t a etrier perforant ou de 3A6po (4,76 mm) qui pourrait

reduire le debit d'eau et qui se bouche plus facilement.

5. On est maintenant pr_t a connecter letuyau en cuivre. Utiliser

un tuyau en cuivre mou de 1/4po (6,35 mm) de dia. ext. pour

I'alimentation en eau froide.

• Mesurer a partir du raccord a I'avant de la machine

gla(_ons jusqu'au tuyau d'eau froide. Ajouter 3 pieds (91,4

cm) pour _tre certain que la Iongueur est suffisante. Cette

mesure represente la Iongueur de tuyau de cuivre mou de

1Apo (6,35 mm) de dia. ext. requise pour faire le

raccordement. IIfaut s'assurer que les deux extremit6s

du tuyau en cuivre sent bien coupees a angle droit.

• Installer le manchon et I'ecrou acompression sur le tuyau

en cuivre (voir I'illustration). Inserer I'extremit6 du tuyau

aussi profondement que possible darts I'extremit6 de

sortie et a I'equerre. Visser I'ecrou a compression sur

I'extremit6 de la sortie a I'aide d'une cle reglable. Ne pas

serrer a I'exces.

................. 1

8 ...........................2

1. Tuyaud'alimentation eneau froide 5. Ecrou de compression

2. Bride 6. Manchon a compression

3. Tuyauen cuivre 7.Robinet d'arr_t

4. Raccord (achet_) 8. Ecrou de lagarniture

Placer I'extremite libre du tuyau dans un contenant ou evier

et retablir I'alimentation principale en eau pour nettoyer le

tuyau jusqu'a ce que I'eau sorte propre. Fermer le robinet

d'arr_t sur le tuyau d'alimentation en eau.

REMAROUE : II faut toujours vidanger le tuyau d'alimentation

en eau avant de faire le raccordement final sur I'entree du

robinet pour prevenir tout mauvais fonctionnement possible

du robinet.

7. Courber le tuyau de cuivre de fa9on a faire un raccordement

sur I'entree du robinet qui se trouve a I'arriere de la machine

glagons (voir I'illustration).

VUE ARRII_RE

1. Tuyau de vidange (modeles avec

pompe de vidange seulement)

2. Tuyau de ventilation (modeles avec

pompe de vidange seulement)

3. Tuyau d'alimentation en eau

Visser I'ecrou dans le raccord a I'extremite du tuyau en

cuivre. Serrer I'ecrou manuellement. Ensuite le serrer deux

tours de plus avec une cle. Ne pas serrer a I'exces.

1 2 3 4 3 2

1. Canalisation jusqu'a la 3. Bague (achet_e)

machine a glaqons 4. Raccord (achet_)

2. Ecrou (achet_)

Retirer les deux vis du panneau d'acces inferieur et les deux

vis de la grille a la base du support du panneau avant. Tirer

vers I'avant pour retirer le panneau d'acces inferieur.

REMARQUE : Pour emp_cher les bruits de tuyau, il faut

s'assurer que les tuyaux en cuivre ne touchent pas le parois

de la machine a glagons ni d'autres composants interieurs.

VUE AVANT

(14,5 cm)

1. Vidange du bacb eau

2. Robinet

10. OUVRIR le robinet d'arr_t.

11. Voir s'il y a des fuites. Serrer tousles raccords (y compris les

raccordements de la valve) ou les ecrous qui coulent.

12. Remettre le panneau d'acces inferieur en place et le fixer &

I'aide des deux vis.

Raccordement de la vidange

Vidange par gravit_

IIfaut raccorder le tuyau de vidange & votre drain de vidange

conformement aux codes et reglements Iocaux et provinciaux. Si

la machine &gla(;ons est fournie avec un drain de vidange par

gravite, il faut suivre les instructions ci-dessous Iors de

I'installation des tuyaux de vidange. Ceci emp_chera que I'eau se

refoule dans le bac d'entreposage de la machine & glagons et

peut-_tre m6me sur le plancher et cause des dommages.

• Les tuyaux de vidange doivent avoir au moins % pc

(15,88 mm) de diametre interieur.

Les tuyaux de vidange doivent avoir une pente de 1 pc pour

chaque 48 po (25,40 mm pour chaque 122 cm) de Iongueur

ou une pente de ¼ pc pour chaque 12 po (6,35 mm/30,48

cm) et ne comporter aucun point bas ou I'eau pourrait

stagner.

• Les drains de vidange de plancher doivent _tre suffisamment

grands pour recevoir I'eau de vidange provenant de toutes

sources.

L'installation ideale a un tuyau de rejet &I'egout avec un

reducteur de vidange PVC de 11/2pc (3,81 cm) a 2 po

(5,08 cm) installe directement sous la sortie du tuyau de

vidange comme a I'illustration. IIfaut maintenir un ecart anti-

retour de 1 po (2,54 cm) entre le tuyau de la pompe de

vidange et le tuyau de rejet a I'egout.

• II sera peut-_tre souhaitable d'isoler le tuyau de vidange

completement jusqu'a I'entree du drain de vidange.

Apres avoir verifi6 que le systeme de vidange est adequat, il faut

preceder tel que decrit ci-dessous pour bien mettre la machine

gla(_ons en place :

1. Brancher la machine a gla9ons ou reconnecter le courant

electrique.

2. Verifier a nouveau la machine a glagons pour s'assurer qu'elle

est bien d'aplomb. Voir la section "Nivellement".

3. Pousser la machine a gla(_ons a sa place de sorte que le

tuyau de vidange de la machine soit place au-dessus du

reducteur du drain de vidange en PVC.

VUELATERALE

(2,5 cm)

23" 3

(58,4 cm) 4

2" - 1 1/2"

(5 cm - 3,8 cm)

1. Tuyau de vidange

2. Ecart anti-retour de 1po (2,54 cm)

3. R_ducteur du drain de vidange PVC

4. Le centre du drain devrait se trouver a 23 pc (58,4 cm) du devant de

la porte (avec ou sans le panneau de ¾ pc (1,91 crn) sur la porte).

4. Si le code sanitaire local I'exige, sceller la machine sur le

plancher a I'aide d'un produit de calfeutrage approuve une

fois que les raccordements d'eau et d'electricit6 ont ete faits.

Syst_me & pompe de vidange (sur certains modules)

Raccorder le tuyau de la pompe de vidange (fournie avec la

machine) au drain de vidange conformement atousles codes et

reglements Iocaux ou provinciaux.

REMARQUE : Si le tuyau de vidange devient tordu et I'eau ne

peut passe vidanger, votre machine a glagons ne fonctionnera

pas.

OUTILLAGE NI_CESSAIRE : cle de ¾e po, cle de 1/4po, couteau

mastic plat, tournevis Phillips

Axe

Vis de charniere a t_te hexagonale 5/16po

Vis de poign_e

Vis d'embout

Pour retirer la porte des charni_res :

1. Debrancher la machine a glat:ons ou deconnecter la source

de courant electrique.

2. Oter les vis de la poignee et la poignee (sur certains

modeles). Garder les pieces ensemble et les mettre de c6t&

3. Retirer I'axe de la charniere superieure.

4. Retirer la porte des charnieres et revisser I'axe superieur dans

la charniere superieure.

5. Inverser les embouts de porte comme suit :

• Oter les deux vis et embouts (superieurs et inferieurs).

• Placer I'embout superieur & la partie inferieure du c6te

oppose de la porte avec le long c6te plat face au devant

de la porte.

• Placer I'embout inferieur a la partie superieure du c6te

oppose de la porte avec le long c6te plat face au devant

de la porte.

6. Mettre la porte de c6t&

Inversion des charni_res :

1. Devisser et enlever la charniere superieure. Remettre les vis

dans les trous de charniere vides.

2. Oter les vis du c6te inferieur oppose de la caisse de la

machine & glagons. Inverser la charniere superieure de telle

sorte que I'axe pointe vers le haut. Placer la charniere du c6te

oppose inferieur de la machine & glagons et serrer les vis.

3. Enlever la douille de plastique de I'axe de la charniere de la

"vieille" charniere inferieure et la replacer sur la nouvelle

charniere inferieure.

4. Oter les vis de la "vieille" charniere inferieure et la charniere.

Remettre les vis darts les trous de charniere vides.

5. Oter les vis du c6te superieur oppose de la caisse de la

machine & glagons. Inverser la charniere de telle sorte que

I'axe pointe vers le bas. Placer la charniere du c6te oppose

superieur de la machine a glagons et serrer les vis.

6. Oter I'axe de la charniere superieure.

R_installation de la porte sur les charni_res :

1. Placer la douille de plastique de la charniere dans le trou de la

charniere superieure sur la porte. Aligner la porte avec le trou

de la charniere superieure et reinstaller I'axe superieur.

2. Reinstaller la poignee et les vis de la poignee.

Charni_re sup_rieure

1.Axe

2.Douille de I'axe de lacharniere

3. Charniere

4. Visde charniere a t_te hexagonale

Charni_re inf_rieure

-.._

"_ t

...................................................4

1. Vis de charniere a t_te hexagonale

2. Douille de I'axe de la charniere

3. Charniere

4. Axe

Inversion du Ioquet de porte :

Oter les bouchons de trous du c6te oppose de la porte.

Oter les vis du Ioquet de porte magnetique et les reinstaller

du c6te oppose de la porte.

Pousser les bouchons de trous en place du c6te oppose de

la porte.

Brancher la machine a glat;ons ou reconnecter la source de

courant electrique.

IIest possible que votre nouvelle machine a glagons emette des

bruits qui ne vous sont pas familiers. Comme ces bruits sont

nouveaux, ils peuvent vous inquieter. La plupart de ces nouveaux

bruits sont normaux. Des surfaces dures comme le plancher, les

murs et les armoires peuvent faire paraftre les bruits plus forts

qu'en r_alit& Les descriptions suivantes indiquent les genres de

bruits qui peuvent _tre nouveaux pour vous et leur cause.

• Vous entendrez un bourdonnement Iorsque la valve d'eau

s'ouvre pour remplir le reservoir d'eau pour chaque

programme.

• Des vibrations sonores peuvent provenir de I'ecoulement du

refrigerant, de la canalisation d'eau ou d'articles places sur la

machine a gla(;ons.

• Le compresseur a haute efficacite peut produire un son aigu

ou de pulsation.

• L'eau coulant sur la plaque d'evaporation peut produire un

son d'eclaboussement.

• L'eau coulant de la plaque d'evaporation au reservoir d'eau

peut produire un son d'eclaboussement.

• ,A,la fin de chaque programme, vous pouvez entendre un

gargouillement attribuable au refrigerant qui circule dans

votre machine a gla(;ons.

• Vous pouvez entendre de I'air qui est transmis au condenseur

par le ventilateur du condenseur.

• Au cours du programme de recolte, vous pouvez entendre un

"bruit sourd" Iorsque la plaque de glace glisse de

I'evaporateur sur la grille de coupe.

Lors de la mise en marche initiale de la machine a gla(;ons, il

est possible que vous entendiez I'eau couler continuellement.

La machine a gla9ons est programmee pour effectuer un

programme de ringage avant de commencer a fabriquer de la

glace.

La page charge ...

KitchenAid KUIS15PRHB4 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KUIS15PRHB4

Catégorie: Fabricants de glaçons

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KUIS15PRHB4 Owner's manual

KitchenAid KUIS15PRHB4 Le manuel du propriétaire

Ce manuel convient également à

KitchenAid KUIS15PRHB4 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents