Yes AK7436AS Manuel utilisateur

WWW.ZEPHYRONLINE.COM

NOV20.0101

Airﬂow Control Technology

TM

C

Tidal II

AK7400AS, AK7436AS, AK7448AS

EN Use, Care, and Installation Guide

FR Guide d’utilisation, d’entretien et d’installation

2

Tidal II Use, Care, and Installation Guide

TIDAL II

WALL

PRO

3

Tidal II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Contents

Page

Safety Information ............................................................................ 4-6

Types of Safety Warnings ................................................................... 4

General Safety ..................................................................................4-5

Operation ........................................................................................... 6

Electrical Requirements ...................................................................... 6

Federal Communication Commission Interface Statement ................. 6

List of Materials ................................................................................... 7

Installation Instructions .................................................................... 8-20

Ducting Calculation Sheet .................................................................. 8

Mounting Height, Clearance, & Ducting ...........................................9-10

Ducting Options .................................................................................11

Hood Speciﬁcations ............................................................................12

Electrical Supply .................................................................................13

Cable Lock .........................................................................................13

Horizontal Ducting Conversion ........................................................ 14-16

PBD-1300B Dual Blower Installation ..................................................17-19

Mounting the Hood ............................................................................ 20

Features & Controls ..........................................................................21-27

Proximity Controls ...........................................................................21-23

Zephyr Connect ..............................................................................24-25

Optional RF Remote Control ............................................................26-27

Maintenance ................................................................................... 28-30

Hood & Filter Cleaning .....................................................................28-29

LumiLight LED ................................................................................... 30

ACT™ Conversion .............................................................................31-33

Airﬂow Control Technology (ACT™) ....................................................31

Enabling ACT™ ................................................................................ 32-33

Wiring Diagram ............................................................................... 34-35

Troubleshooting............................................................................... 36-38

List of Parts & Accessories .................................................................. 39

Notes ..................................................................................................40

Limited Warranty ............................................................................... 41

Product Registration ...........................................................................42

4

Tidal II Use, Care, and Installation Guide

TIDAL II

WALL

PRO

Safety Information

Your safety and the safety of others are very important.

We have provided many important safety messages in this

manual for your appliance. Always read and obey all safety

messages.

This is the Safety Alert Symbol. This symbol alerts you to

potential hazards that can cause severe bodily injury or death.

All safety messages will follow the Safety Alert Symbol and either

the words “DANGER” “WARNING” or “CAUTION”

DANGER

Danger means that failure to heed this safety statement may

result in severe injury or death.

READ AND SAVE THESE INSTRUCTIONS

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a) Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the manufacturer.

b) Before servicing or cleaning unit, switch power o at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

General Safety

WARNING

Warning means that failure to heed this safety statement

may result in extensive product damage, serious personal

injury, or death.

CAUTION

Caution means that failure to heed this safety statement

may result in minor or moderate personal injury, property or

equipment damage.

WARNING

To reduce the risk of ﬁre or electric shock, do not use this fan

with any solid-state control device.

WARNING

CAUTION

For General Ventilating Use Only. Do Not Use To Exhaust

Hazardous Or Explosive Materials And Vapors. Take care

when using cleaning agents or detergents. Suitable for use in

household cooking area.

WARNING

WARNING - TO REDUCE THE RISK OF A RANGE TOP GREASE

FIRE:

a) Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may ignite.

Heat oils slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or

when ﬂambeing food. (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flambe’).

c) Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or ﬁlter.

d) Use proper pan size. Always use cookware appropriate for

the size of the surface element.

5

Tidal II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Safety Information

WARNING

READ AND SAVE THESE INSTRUCTIONS

WARNING - TO REDUCE THE RISK OF INJURY TO PERSONS

IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWING:

a) SMOTHER FLAMES with a close-ﬁtting lid, cookie sheet, or

metal tray, then turn o the burner. BE CAREFUL TO PREVENT

BURNS. If the ﬂames do not go out immediately, EVACUATE AND

CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN – You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels – a

violent steam explosion will result.

d) Use an extinguisher ONLY if:

1) You know you have a Class ABC extinguisher, and you

already know how to operate it.

2) The ﬁre is small and contained in the area where it

started.

3) The ﬁre department is being called.

4) You can ﬁght the ﬁre with your back to an exit

Based on “Kitchen Firesafety Tips” published by NFPA.

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

CAUTION

To reduce risk of ﬁre and to properly exhaust air outside, do

not vent exhaust air into spaces within walls, ceilings, attics,

crawl spaces, or garages.

WARNING

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a) Installation work and electrical wiring must be done by

qualiﬁed person(s) in accordance with all applicable codes and

standards, including ﬁre-rated construction.

b) Sucient air is needed for proper combustion and

exhausting of gases through the ﬂue (chimney) of fuel burning

equipment to prevent back drafting. Follow the heating

equipment manufacturer’s guideline and safety standards such

as those published by the National Fire Protection Association

(NFPA), and the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE), and the local code

authorities.

c) When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

d) Ducted fans must always be vented to the outdoors.

e) If this unit is to be installed over a tub or shower, it must be

marked as appropriate for the application and be connected

to a GFCI (Ground Fault Circuit Interrupter) - protected branch

circuit.

WARNING

Prop. 65 Warning for California Residents: This product may

contain chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

6

Tidal II Use, Care, and Installation Guide

TIDAL II

WALL

PRO

Safety Information

Operation

Ź Always leave safety grilles and ﬁlters in place. Without these components, operating blowers could catch onto hair, ﬁngers and

loose clothing.

Ź The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,

maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to negligence and

the warranty of the unit automatically expires due to improper maintenance.

NOTE: Please check www.zephyronline.com for revisions before doing any custom work.

Electrical Requirements

Important:

Ź Observe all governing codes and ordinances.

Ź It is the customer’s responsibility to be aware of these below:

Ź To contact a qualiﬁed electrical installer.

Ź To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 latest

edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local codes

and ordinances.

Ź If codes permit and a separate ground wire is used, it is recommended that a qualiﬁed electrician determine that the ground path

is adequate.

Ź Do not ground to a gas pipe.

Ź Check with a qualiﬁed electrician if you are not sure the range hood is properly grounded.

Ź Do not have a fuse in the neutral or ground circuit.

Ź This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit protected

by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to Electrical Diagram

on product.

Ź A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase and

install appropriate connector if necessary.

* National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269

** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

Federal Communication Commission Interface Statement

Ź This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

Ź This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following

measures:

Ź Reorient or relocate the receiving antenna.

Ź Increase the separation between the equipment and receiver.

Ź Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

Ź Consult the dealer or an experienced radio/TV technician for help.

READ AND SAVE THESE INSTRUCTIONS

7

Tidal II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

List of Materials

Parts Not Supplied

Ducting, conduit and all installation tools

Cable locking connector (if required by local codes)

Duct cover extension kit

Recirculating kit

RF remote control

Dual blower motor

Wood board to hang hood (WxDxH)

AK7400AS: 27” x 1/2” x 4”

AK7436AS: 33” x 1/2” x 4”

AK7448AS : 45” x 1/2” x 4”

Parts Supplied

Quantity Part

1Hood

2 Pro bae ﬁlters (AK7400AS, AK7436AS)

3 Pro bae ﬁlters (AK7448AS)

2 LumiLight LED, 6W (pre-installed) (AK7400AS, AK7436AS)

4 LumiLight LED, 6W (pre-installed) (AK7448AS)

1 8” round backdraft damper (pre-installed)

1 3-1/4” x 10” rectangular collar with damper

1 Single blower motor (pre-installed)

1 Top cover plate (for horizontal ducting)

1 Hardware package

#6 x 1” (4 )

#6 x 1-1/2” (4 )

#6 x 2” (4 )

M3.5 x 8 (8)

Wire Caps (3)

3/16 x 3/8 (4)

8

Tidal II Use, Care, and Installation Guide

TIDAL II

WALL

PRO

Installation Instructions

Duct pieces

To t al

Equivalent number

length x used =

3- 1/ 4” x 10”

Rect.,

straight

1 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

5 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

90

0

elbow

20 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

90

0

15 Ft.

x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

45

0

9 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

straight

1 Ft. x ( ) =

Ft.

Subtotal column 1 =

Duct pieces

To t al

Equivalent number

length x used =

6”, 7”, 8”, 10”

Round, wall

cap with

damper

30 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round

roof cap

30 Ft. x ( ) =

Ft.

Subtotal column 2 =

Subtotal column 1 =

Total ductwork =

Maximum Duct Length: For satisfactory air movement,

the total duct length

should not exceed 150 equivalent feet.

6” round to

3- 1/ 4” x 10”

rect.

transition

1 Ft. x ( ) =

Ft.

6” round to

3- 1/ 4” x 10”

rect.

transition

90

0

elbow

16 Ft. x ( ) =

Ft.

7” round to

3 1/ 4” x 10”

rect.

transition

8 Ft. x ( ) =

Ft.

7” round to

3- 1/ 4” x 10”

rect.

transition

90

0

elbow

23 Ft. x ( ) =

Ft.

elbow

7” to 6” or

8” to 7” Round

tapered

reducer

25 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 90

0

elbow

15 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 45

0

elbow

9 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 90

0

ﬂat elbow

24 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect.

wall cap

with damper

30 Ft. x ( ) =

Ft.

Ft. x ( ) =

Ft.

15

6”, 7“, 8”

Round

in-line

damper

Ducting Calculation Sheet

9

Tidal II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Mounting Height, Clearance, & Ducting

24” min.

34” max.

36”

10

Tidal II Use, Care, and Installation Guide

TIDAL II

WALL

PRO

Installation Instructions

Mounting Height, Clearance, & Ducting

A minimum of 8” round duct or 3-1/4” x 10” rectangular duct is recommended to maintain maximum

air ﬂow eciency for single blower and 10” round duct for dual internal blower for both vertical and

horizontal ducting.

Always use rigid type metal ducts only. Flexible ducts could restrict air ﬂow by up to 50%.

Also use the ducting calculation sheet (on page 11) to compute total available duct run when using

elbows, transitions and caps.

ALWAYS, when possible, reduce the number or transitions and turns. If long duct run is required,

increase duct size from 8” to 10”.

If turns or transitions are required; install as far away from hood duct output and as far apart,

between the two as possible.

Minimum mount height between range top to hood bottom should be no less than 24”.

Maximum mount height should be no higher than 34”.

It is important to install the hood at the proper mounting height. Hoods mounted too low could result

in heat damage and ﬁre hazard; while hoods mounted too high will be hard to reach and will lose its

performance and eciency.

If available, also refer range manufacturer’s height clearance requirements and recommended hood

mounting height above range. Always check your local codes for any dierences.

Duct cover extension kit available for ceiling heights up to 12 feet. Turn to the list of parts and

accessories section for part number and ordering information.

For shipment and installation damages:

Ź Please fully inspect unit for damage before installation.

Ź If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or

replacement.

Ź If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.

Ź If the unit is damaged by the installer (if other than the customer), repair of replacement must be

made by arrangement between customer and installer.

11

Tidal II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Ducting Options

Ź Use single wall rigid metal ductwork only.

Ź Fasten all connections with sheet metal screws and tape all joints w/ certiﬁed Silver Tape or Duct

Tape.

Fire Hazard: NEVER exhaust air or terminate ductwork into

spaces between walls, crawl spaces, ceilings, attics, or garages.

All exhaust must be ducted to the outside, unless using the

recirculating option.

WARNING

Sot or crawl space

Roof Pitch w/

Flashing & Cap

Rear Ducting

Side wall cap

w/ gravity damper

ductless

recirculating

12

Tidal II Use, Care, and Installation Guide

TIDAL II

WALL

PRO

Installation Instructions

Ů

27-7/8” (30“)

33-7/8” (36”)

45-13/16” (48”)

1-1/8”

8-9/16”

1”

6”

11-9/16”

2-5/8”

*7-3/4”

**9-15/16”

29-15/16” (30“)

35-7/8” (36”)

47-7/8” (48”)

3-3/8” (30“)

6-3/8” (36”)

12-3/8” (48”)

1-11/16”

12”

18”

12-9/16”

24”

4”

Top

Back

Side

*9-1/2”

**14-3/16”

*7-7/8”

**10-3/8”

*7-7/8”

**10-3/8”

***3-3/16”

*9-1/2”

**14-3/16”

***9-7/8”

* 8” round ducting

** 10” round ducting

*** Rectangular ducting

27-3/8” (30“, 36”)

35-1/4” (48”)

18”

5-1/4”

21-1/4”

13-9/16”

16-1/8”

3-1/4”

1-11/16”

Back

13

Tidal II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Electrical Supply

Electrical wiring must be done by qualiﬁed person(s) in

accordance with all applicable codes and standards. Turn o

electrical power at service entrance before wiring.

WARNING

For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not

use extension cord or adapter plug with this appliance.

Follow national electrical codes or prevailing local codes and ordinances.

This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly

grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring

must be 2 wire w/ ground. Please also refer to the Electrical Diagram labeled on product.

Cable Lock

A cable locking connector (not supplied) might be required by local codes. Check with local

requirements and codes, purchase and install appropriate connector if necessary. (FIG. A)

Cable Lock

FIG. A

14

Tidal II Use, Care, and Installation Guide

TIDAL II

WALL

PRO

Installation Instructions

Horizontal Ducting Conversion

By default the Tidal II is pre-conﬁgured for 8” round vertical ducting. These steps are for 8” round

and 3-1/4”x10” rectangular horizontal ducting. If you are continuing with vertical ducting, please skip

these steps.

3. Using a ﬂat-head screwdriver,

remove the smaller rectangular

knock-out plate (A) for 3-1/4” x

10” rectangular ducting or the

larger knock-out plate (B) for 8”

round ducting located on the

back of hood.

1. Disconnect blower plug.

2. Remove (4) screws from interior

of hood body attaching single

blower plate to top of hood body.

Remove single blower and single

blower plate.

A

B

15

Tidal II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Horizontal Ducting Conversion

4. Remove (4) screws attaching

blower to blower plate. Turn

blower 180 degrees and reattach

to blower plate.

5. Position single blower with single

blower plate as shown. Be sure to

tuck back of single blower plate

into tabs at back of hood. Secure

single blower plate to back of

hood using (4) screws removed

from step 2.

6. Attach 8” round duct collar or

3-1/4” x 10” rectangular duct

collar to back of hood body using

(4) M3.5 x 8 screws.

16

Tidal II Use, Care, and Installation Guide

TIDAL II

WALL

PRO

Installation Instructions

Horizontal Ducting Conversion

7. From inside hood body, position

top cover plate to top of hood

body. From outside hood body,

attach top cover plate to top of

hood body using (4) 3/16 x 3/8

screws.

8. Connect blower plug.

17

Tidal II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

PBD-1300B Dual Blower Installation

This range hood is equipped standard with a single blower vertical duct option. To convert from

single blower vertical ducting to dual blower vertical ducting please following the instructions below.

PBD-1300B dual blower kit is compatible with all Tidal II sizes.

1. Remove the bae ﬁlters and

if applicable, remove the side

panels. Disconnect blower plug.

2. Remove (4) screws at top of

hood body attaching blower to

blower plate. Remove blower from

interior of hood body.

3. Remove (4) screws from interior

of hood body attaching blower

plate to hood body. Remove

blower plate.

4. Install dual blower plate from

PBD-1300B kit into hood body.

Attach by (4) screws previously

removed from step 3.

18

Tidal II Use, Care, and Installation Guide

TIDAL II

WALL

PRO

Installation Instructions

PBD-1300B Dual Blower Installation

5. Install previously removed blower

onto one side of dual blower plate

and attach by (4) previously

removed screws from step 2.

6. Install blower from PBD-1300B

kit onto other side of dual blower

plate by (4) 3/16 x 3/8 screws.

7. Dual blower screw mount

locations.

8. Remove (4) screws to remove the

light panel. Install dual blower

PCB inside the hood body.

19

Tidal II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

PBD-1300B Dual Blower Installation

9. Refer to page 32-33 section for

this step. Connect the wiring

from the dual blower including

both blower plugs, blower cable

6 pin connector (E), dual blower

switch cable (H), black single pin

power cord from dual blower (K),

and white single pin power cord

(F) to dual blower PCB.

NOTE: To secure the 10” transition adapter to top of hood a cut out of 14-1/2” width x 10-1/2” depth

will need to be made in the cabinet bottom.

If internal cabinet dimensions prevent this size of a cut out then the 10” transition adapter may be

mounted to the cabinet bottom rather than the top of the hood. Cut out dimensions for this type of

installation are 13-1/4” width x 6-1/4” depth.

10. Place 10” round adapter

(included with PBD-1300B) on top

of hood and secure with (4) M3.5

x 8 screws.

20

Tidal II Use, Care, and Installation Guide

TIDAL II

WALL

PRO

Installation Instructions

Mounting the Hood

If recirculating range hood refer to the manual included with ZRC-70xxC recirculating kit or on our

website prior to installing hood.

1. Select preferred ducting application (vertical

or horizontal) and prepare hood. Remove the

safety screw on top of hood body.

2. Choose desired height above cooking surface

(24” min). Level and mark hood bottom, line A

(FIG. B)

3. Plum and mark center line on wall.

4. Level and mark top of wood board, line B (FIG.

B) 16-7/8” from line A.

5. Mark center line of wood board. Center and

align top of board with line B. Secure wood

board to studs using (4) #6 wood screws. Wood

Board Dimensions: (W x D x H)

30”: 27” x 1/2” x 4”

36”: 33” x 1/2” x 4”

48”: 45” x 1/2” x 4”

FIG. B

C/L

A

B

16-7/8”

min

24”

4”

wood board

At least two installers are required due to the

weight and size of the hood.

CAUTION

6. Prepare duct pipe and duct cut outs in upper cabinet if needed or wall if horizontally ducting

hood. Prepare electrical wiring and electrical cut outs in upper cabinet if needed or wall if

horizontal electrical hook up is required. Refer to hood speciﬁcations on page 15 for dimensions.

7. Mount hood onto wood board and secure using (4) #6 wood screws. Further secure hood onto wall

through lower body screw holes by (2) #6 wood screws.

8. Install electrical and duct work and seal with certiﬁed aluminum duct tape.

9. If using RF remote control, remove bae ﬁlters and remove the light panel by (4) screws and

extend the blue antenna wire. There is no need to secure it. Reinstall light panel and bae ﬁlters.

10. Power up hood and check for leaks around duct tape.

La page charge ...

Yes AK7436AS Manuel utilisateur

Yes AK7436AS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents