ASROCK P43TWINS Le manuel du propriétaire

11

1

ASRock Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or trans-

lated in any language, in any form or by any means, except duplication of documen-

tation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identifica-

tion or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or omissions

that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any kind,

either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose. In no event shall

ASRock, its directors, officers, employees, or agents be liable for any indirect, special,

incidental, or consequential damages (including damages for loss of profits, loss of

business, loss of data, interruption of business and the like), even if ASRock has been

advised of the possibility of such damages arising from any defect or error in the guide

or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic

substance controlled in Perchlorate Best Management Practices (BMP) regulations

passed by the California Legislature. When you discard the Lithium battery in

California, USA, please follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see

www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

Published May 2008

22

2

ASRock Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

(P43D1600T(P43D1600T

(P43D1600T

winswins

wins

-1394 / P43D1600T-1394 / P43D1600T

-1394 / P43D1600T

wins)wins)

wins)

1 PS2_USB_PWR1 Jumper 21 SPI BIOS Chip

2 CPU Fan Connector (CPU_FAN1) 22 Chassis Fan Connector (CHA_FAN1)

3 775-Pin CPU Socket 23 Front Panel IEEE 1394 Header

4 North Bridge Controller (FRONT_1394)

5 2 x 240-pin DDR2 DIMM Slots 24 Clear CMOS Jumper (CLRCMOS1)

(Dual Channel A: DDRII_A1, DDRII_B1; Yellow) 25 Floppy Connector (FLOPPY1)

6 2 x 240-pin DDR2 DIMM Slots 26 DeskExpress Hot Plug Detection Header

(Dual Channel B: DDRII_A2, DDRII_B2; Orange) (IR1)

7 2 x 240-pin DDR3 DIMM Slots 27 COM Port Header (COM1)

(Dual Channel C: DDR3_A1, DDR3_B1; Green) 28 PCI Slots (PCI1 - 3)

8 IDE1 Connector (IDE1, Blue) 29 Front Panel Audio Header (HD_AUDIO1)

9 FSB2 / FSB3 Jumpers 30 HDMI_SPDIF Header (HDMI_SPDIF1)

10 South Bridge Controller 31 Internal Audio Connector: CD1 (Black)

11 SATAII Connector (SATAII_1 (Port0), Red) 32 WiFi/E Header (WIFI/E)

12 SATAII Connector (SATAII_2 (Port1), Red) 33 PCI Express x1 Slot (PCIE4)

13 SATAII Connector (SATAII_4 (Port3), Red) 34 FSB1 Jumper

14 SATAII Connector (SATAII_3 (Port2), Red) 35 PCI Express x1 Slot (PCIE3)

15 SATAII Connector (SATAII_6 (Port5), Orange) 36 PCI Express 2.0 x16 Slot (PCIE2, Green)

16 SATAII Connector (SATAII_5 (Port4), Red) 37 PCI Express x1 Slot (PCIE1/DE)

17 System Panel Header (PANEL1) 38 ATX Power Connector (ATXPWR1)

18 USB 2.0 Header (USB4_5, Blue) 39 eSATAII Connector (eSATAII_TOP)

19 USB 2.0 Header (USB6_7, Blue) 40 ATX 12V Connector (ATX12V1)

20 Chassis Speaker Header (SPEAKER 1)

33

3

ASRock Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayout (P43Tayout (P43T

ayout (P43T

wins1600)wins1600)

wins1600)

1 PS2_USB_PWR1 Jumper 20 Chassis Speaker Header (SPEAKER 1)

2 CPU Fan Connector (CPU_FAN1) 21 SPI BIOS Chip

3 775-Pin CPU Socket 22 Chassis Fan Connector (CHA_FAN1)

4 North Bridge Controller 23 Clear CMOS Jumper (CLRCMOS1)

5 2 x 240-pin DDR2 DIMM Slots 24 Floppy Connector (FLOPPY1)

(Dual Channel A: DDRII_A1, DDRII_B1; Yellow) 25 DeskExpress Hot Plug Detection Header

6 2 x 240-pin DDR2 DIMM Slots (IR1)

(Dual Channel B: DDRII_A2, DDRII_B2; Orange) 26 COM Port Header (COM1)

7 2 x 240-pin DDR3 DIMM Slots 27 PCI Slots (PCI1 - 3)

(Dual Channel C: DDR3_A1, DDR3_B1; Green) 28 Front Panel Audio Header (HD_AUDIO1)

8 IDE1 Connector (IDE1, Blue) 29 HDMI_SPDIF Header (HDMI_SPDIF1)

9 FSB2 / FSB3 Jumpers 30 Internal Audio Connector: CD1 (Black)

10 South Bridge Controller 31 WiFi/E Header (WIFI/E)

11 SATAII Connector (SATAII_1 (Port0), Red) 32 PCI Express x1 Slot (PCIE4)

12 SATAII Connector (SATAII_2 (Port1), Red) 33 FSB1 Jumper

13 SATAII Connector (SATAII_4 (Port3), Red) 34 PCI Express x1 Slot (PCIE3)

14 SATAII Connector (SATAII_3 (Port2), Red) 35 PCI Express 2.0 x16 Slot (PCIE2, Green)

15 SATAII Connector (SATAII_6 (Port5), Orange) 36 PCI Express x1 Slot (PCIE1/DE)

16 SATAII Connector (SATAII_5 (Port4), Red) 37 ATX Power Connector (ATXPWR1)

17 System Panel Header (PANEL1) 38 eSATAII Connector (eSATAII_TOP)

18 USB 2.0 Header (USB4_5, Blue) 39 ATX 12V Connector (ATX12V1)

19 USB 2.0 Header (USB6_7, Blue)

44

4

ASRock Motherboard

EnglishEnglish

English

ASRASR

ASR

ock 1394_SPDIF I/O (P43D1600Tock 1394_SPDIF I/O (P43D1600T

ock 1394_SPDIF I/O (P43D1600T

winswins

wins

-1394)-1394)

-1394)

To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. After restarting your computer, you will find “Mixer” tool on your system.

Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click

“ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA

Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek

HDA Audio 2nd output” to use front panel audio.

** If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”.

See the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker

(No. 8) (No. 5) (No. 6) (No. 4)

2 V -- -- --

4VV----

6 VVV--

8 VVVV

LAN Port

ACT/LINK

LED

SPEED

LED

1 PS/2 Mouse Port (Green) 9 Microphone (Pink)

2 IEEE 1394 Port 10 USB 2.0 Ports (USB01)

* 3 LAN RJ-45 Port 11 USB 2.0 Ports (USB23)

4 Side Speaker (Gray) 12 USB 2.0 Ports (USB89)

5 Rear Speaker (Black) 13 eSATAII Port

6 Central / Bass (Orange) 14 Optical SPDIF Out Port

7 Line In (Light Blue) 15 Coaxial SPDIF Out Port

**8 Front Speaker (Lime) 16 PS/2 Keyboard Port (Purple)

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED

indications.

LAN Port LED Indications

SPEED LED Activity/Link LED

Status Description Status Description

Off 10Mbps connection Off No link

Orange 100Mbps connection Orange Linked

Green 1Gbps connection Blinking Data Activity

55

5

ASRock Motherboard

EnglishEnglish

English

LAN Port

ACT/LINK

LED

PEED

LED

ASRASR

ASR

ock SPDIF I/O (P43D1600Tock SPDIF I/O (P43D1600T

ock SPDIF I/O (P43D1600T

wins)wins)

wins)

To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. After restarting your computer, you will find “Mixer” tool on your system.

Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click

“ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA

Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek

HDA Audio 2nd output” to use front panel audio.

** If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”.

See the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker

(No. 7) (No. 4) (No. 5) (No. 3)

2 V -- -- --

4VV----

6 VVV--

8 VVVV

LAN Port

ACT/LINK

LED

SPEED

LED

1 PS/2 Mouse Port (Green) 9 USB 2.0 Ports (USB01)

* 2 LAN RJ-45 Port 10 USB 2.0 Ports (USB23)

3 Side Speaker (Gray) 11 USB 2.0 Ports (USB89)

4 Rear Speaker (Black) 12 eSATAII Port

5 Central / Bass (Orange) 13 Optical SPDIF Out Port

6 Line In (Light Blue) 14 Coaxial SPDIF Out Port

**7 Front Speaker (Lime) 15 PS/2 Keyboard Port (Purple)

8 Microphone (Pink)

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED

indications.

LAN Port LED Indications

SPEED LED Activity/Link LED

Status Description Status Description

Off 10Mbps connection Off No link

Orange 100Mbps connection Orange Linked

Green 1Gbps connection Blinking Data Activity

66

6

ASRock Motherboard

EnglishEnglish

English

ASRASR

ASR

ock SPDIF I/O (P43Tock SPDIF I/O (P43T

ock SPDIF I/O (P43T

wins1600)wins1600)

wins1600)

1 PS/2 Mouse Port (Green) 9 USB 2.0 Ports (USB01)

2 LAN RJ-45 Port 10 USB 2.0 Ports (USB23)

3 Side Speaker (Gray) 11 USB 2.0 Ports (USB89)

4 Rear Speaker (Black) 12 eSATAII Port

5 Central / Bass (Orange) 13 Optical SPDIF Out Port

6 Line In (Light Blue) 14 Coaxial SPDIF Out Port

* 7 Front Speaker (Lime) 15 PS/2 Keyboard Port (Purple)

8 Microphone (Pink)

To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. After restarting your computer, you will find “Mixer” tool on your system.

Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click

“ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA

Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek

HDA Audio 2nd output” to use front panel audio.

* If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”.

See the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker

(No. 7) (No. 4) (No. 5) (No. 3)

2 V -- -- --

4VV----

6 VVV--

8 VVVV

77

7

ASRock Motherboard

1. Introduction1. Introduction

1. Introduction

Thank you for purchasing ASRock P43D1600Twins-1394 / P43D1600Twins /

P43Twins1600 motherboard, a reliable motherboard produced under ASRock’s consis-

tently stringent quality control. It delivers excellent performance with robust design con-

forming to ASRock’s commitment to quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-step

installation guide. More detailed information of the motherboard can be found in the user

manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might be

updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest VGA cards and CPU support lists on ASRock website

as well. ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please visit

our website for specific information about the model you are using.

www.asrock.com/support/index.asp

1.1 P1.1 P

1.1 P

ackack

ack

age Contentsage Contents

age Contents

ASRock P43D1600Twins-1394 / P43D1600Twins / P43Twins1600 Motherboard

(ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm)

ASRock P43D1600Twins-1394 / P43D1600Twins / P43Twins1600 Quick

Installation Guide

ASRock P43D1600Twins-1394 / P43D1600Twins / P43Twins1600 Support CD

One 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable

One Ribbon Cable for a 3.5-in Floppy Drive

Four Serial ATA (SATA) Data Cables (Optional) (P43D1600Twins-1394 / P43D1600Twins)

Two Serial ATA (SATA) Data Cables (Optional) (P43Twins1600)

One Serial ATA (SATA) HDD Power Cable (Optional)

One HDMI_SPDIF Cable (Optional)

One “ASRock 1394_SPDIF I/O” I/O Panel Shield (P43D1600Twins-1394)

One “ASRock SPDIF I/O” I/O Panel Shield (P43D1600Twins / P43Twins1600)

EnglishEnglish

English

88

8

ASRock Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform - ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm

- All Solid Capacitor design

(For P43D1600Twins-1394 / P43D1600Twins Only)

CPU - LGA 775 for Intel

®

Core

TM

2 Extreme / Core

TM

2 Quad / Core

TM

2 Duo / Pentium

®

Dual Core / Celeron

®

, supporting Penryn Quad

Core Yorkfield and Dual Core Wolfdale processors

- Supports FSB1600/1333/1066/800 MHz (see CAUTION 1)

- Supports Hyper-Threading Technology (see CAUTION 2)

- Supports Untied Overclocking Technology (see CAUTION 3)

- Supports EM64T CPU

Chipset - Northbridge: Intel

®

P43

- Southbridge: Intel

®

ICH10

Memory - Dual Channel DDR3/DDR2 Memory Technology

(see CAUTION 4)

- 2 x DDR3 DIMM slots

- Support DDR3 1333/1066 non-ECC, un-buffered memory

(see CAUTION 5)

- Max. capacity of system memory: 4GB (see CAUTION 6)

- 4 x DDR2 DIMM slots

- Support DDR2 1066/800/667 non-ECC, un-buffered memory

(see CAUTION 5)

- Max. capacity of system memory: 16GB (see CAUTION 6)

Expansion Slot - 1 x PCI Express 2.0 x16 slot (green @ x16 mode)

- 3 x PCI Express x1 slots

- 3 x PCI slots

Audio - 7.1 CH Windows

®

Vista

TM

Premium Level HD Audio

(ALC888 Audio Codec)

LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111B/RTL8111C

- Supports Wake-On-LAN

Rear Panel I/O P43D1600Twins-1394

ASRock 1394_SPDIF I/O

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x Coaxial SPDIF Out Port

- 1 x Optical SPDIF Out Port

- 6 x Ready-to-Use USB 2.0 Ports

- 1 x eSATAII Port

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)

99

9

ASRock Motherboard

EnglishEnglish

English

- 1 x IEEE 1394 Port

- HD Audio Jack: Side Speaker/Rear Speaker/Central/Bass/

Line in/Front Speaker/Microphone (see CAUTION 7)

P43D1600Twins / P43Twins1600

ASRock SPDIF I/O

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x Coaxial SPDIF Out Port

- 1 x Optical SPDIF Out Port

- 6 x Ready-to-Use USB 2.0 Ports

- 1 x eSATAII Port

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)

(P43D1600Twins)

- 1 x RJ-45 LAN Port (P43Twins1600)

- HD Audio Jack: Side Speaker/Rear Speaker/Central/Bass/

Line in/Front Speaker/Microphone (see CAUTION 7)

Connector - 6 x SATAII 3.0Gb/s connectors, support NCQ, AHCI and

“Hot Plug” functions (see CAUTION 8)

- 1 x eSATAII 3.0Gb/s connector (shared with 1 SATAII port)

(see CAUTION 9)

- 1 x ATA133 IDE connector (supports 2 x IDE devices)

- 1 x Floppy connector

- 1 x DeskExpress Hot Plug Detection header

- 1 x COM port header

- 1 x HDMI_SPDIF header

- 1 x IEEE 1394 header (P43D1600Twins-1394)

- CPU/Chassis FAN connector

- 24 pin ATX power connector

- 8 pin 12V power connector

(P43D1600Twins-1394 / P43D1600Twins)

- 4 pin 12V power connector (P43Twins1600)

- CD in header

- Front panel audio connector

- 2 x USB 2.0 headers (support 4 USB 2.0 ports)

(see CAUTION 10)

- 1 x WiFi/E header (see CAUTION 11)

BIOS Feature - 8Mb AMI BIOS (P43D1600Twins-1394 / P43D1600Twins)

- 4Mb AMI BIOS (P43Twins1600)

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

1010

10

ASRock Motherboard

EnglishEnglish

English

WARNING

Please realize that there is a certain risk involved with overclocking, including

adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using

the third-party overclocking tools. Overclocking may affect your system stability, or

even cause damage to the components and devices of your system. It should be

done at your own risk and expense. We are not responsible for possible damage

caused by overclocking.

- AMBIOS 2.3.1 Support

- CPU, DRAM, NB, SB, VTT Voltage Multi-adjustment

- Supports I. O. T. (Intelligent Overclocking Technology)

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version)

Unique Feature - ASRock OC Tuner (see CAUTION 12)

- Hybrid Booster:

- CPU Frequency Stepless Control (see CAUTION 13)

- ASRock U-COP (see CAUTION 14)

- Boot Failure Guard (B.F.G.)

Hardware - CPU Temperature Sensing

Monitor - Chassis Temperature Sensing

- CPU Fan Tachometer

- Chassis Fan Tachometer

- CPU Quiet Fan

- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore

OS - Microsoft

®

Windows

®

2000 / XP / XP 64-bit / Vista

TM

/

Vista

TM

64-bit compliant (see CAUTION 15)

Certifications - FCC, CE, WHQL

* For detailed product information, please visit our website: http://www.asrock.com

1111

11

ASRock Motherboard

EnglishEnglish

English

CAUTION!

1. This motherboard supports native FSB1600/1333/1066/800 MHz. For

normal operation, you do no need to adjust the jumper settings. For

special overclocking mode, please refer to page 19 for proper jumper

settings.

2. About the setting of “Hyper Threading Technology”, please check page

45 of “User Manual” in the support CD.

3. This motherboard supports Untied Overclocking Technology. Please read

“Untied Overclocking Technology” on page 30 for details.

4. This motherboard supports Dual Channel Memory Technology. Before

you implement Dual Channel Memory Technology, make sure to read

the installation guide of memory modules on page 16 for proper

installation.

5. Please check the table below for the CPU FSB frequency and its

corresponding memory support frequency.

CPU FSB Frequency Memory Support Frequency

1600 DDR2 800, DDR2 1066,

DDR3 1066, DDR3 1333

1333 DDR2 667, DDR2 800, DDR2 1066,

DDR3 1066, DDR3 1333

1066 DDR2 667, DDR2 800, DDR2 1066,

DDR3 1066

800 DDR2 667, DDR2 800

6. Due to the operating system limitation, the actual memory size may be

less than 4GB for the reservation for system usage under Windows

®

XP

and Windows

®

Vista

TM

. For Windows

®

XP 64-bit and Windows

®

Vista

TM

64-bit with 64-bit CPU, there is no such limitation.

7. For microphone input, this motherboard supports both stereo and mono

modes. For audio output, this motherboard supports 2-channel, 4-

channel, 6-channel, and 8-channel modes. Please check the table on

page 4, 5 and 6 for proper connection.

8. Before installing SATAII hard disk to SATAII connector, please read the

“SATAII Hard Disk Setup Guide” on page 34 of “User Manual” in the

support CD to adjust your SATAII hard disk drive to SATAII mode. You can

also connect SATA hard disk to SATAII connector directly.

9. This motherboard supports eSATAII interface, the external SATAII

specification. Please read “eSATAII Interface Introduction” on page 26

for details about eSATAII and eSATAII installation procedures.

10. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

Vista

TM

64-bit / Vista

TM

/ XP 64-bit / XP SP1 or SP2 / 2000 SP4.

11. WiFi/E header supports WiFi+AP function with ASRock WiFi-802.11g or

WiFi-802.11n module, an easy-to-use wireless local area network

(WLAN) adapter. It allows you to create a wireless environment and

enjoy the convenience of wireless network connectivity. Please visit our

website for the availability of ASRock WiFi-802.11g or WiFi-802.11n

module. ASRock website http://www.asrock.com

1212

12

ASRock Motherboard

EnglishEnglish

English

1.31.3

1.3

Minimum Hardware RMinimum Hardware R

Minimum Hardware R

equirement Tequirement T

equirement T

able forable for

able for

WindowsWindows

Windows

® ®

®

VistaVista

Vista

TMTM

TM

Premium 2008 and Basic Logo Premium 2008 and Basic Logo

Premium 2008 and Basic Logo

For system integrators and users who purchase this motherboard and

plan to submit Windows

®

Vista

TM

Premium 2008 and Basic logo, please

follow below table for minimum hardware requirements.

CPU Celeron 420

Memory 1GB system memory (Premium)

512MB Single Channel (Basic)

VGA DX10 with WDDM Driver

with 128bit VGA memory (Premium)

with 64bit VGA memory (Basic)

* After June 1, 2008, all Windows

®

Vista

TM

systems are required to meet above

minimum hardware requirements in order to qualify for Windows

®

Vista

TM

Premium 2008 logo.

12. It is a user-friendly ASRock overclocking tool which allows you to surveil

your system by hardware monitor function and overclock your hardware

devices to get the best system performance under Windows

®

environment. Please visit our website for the operation procedures of

ASRock OC Tuner. ASRock website: http://www.asrock.com

13. Although this motherboard offers stepless control, it is not recom-

mended to perform over-clocking. Frequencies other than the recom-

mended CPU bus frequencies may cause the instability of the system

or damage the CPU.

14. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC

system.

15. AHCI function is not supported under Windows

®

2000 OS. It is recom-

mended to use IDE mode under Windows

®

2000. Please refer to page

51 of “User Manual” in the support CD for detailed setup.

1313

13

ASRock Motherboard

2.2.

2.

InstallationInstallation

Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install mother-

board components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet

or the like. Also remember to use a grounded wrist strap or touch

a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded

antstatic pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the

motherboard to the chassis, please do not over-tighten the

screws! Doing so may damage the motherboard.

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

For the installation of Intel 775-LAND CPU,

please follow the steps below.

Before you insert the 775-LAND CPU into the socket, please check if

the CPU surface is unclean or if there is any bent pin on the socket.

Do not force to insert the CPU into the socket if above situation is

found. Otherwise, the CPU will be seriously damaged.

775-Pin Socket Overview

EnglishEnglish

English

1414

14

ASRock Motherboard

EnglishEnglish

English

Step 1. Open the socket:

Step 1-1. Disengaging the lever by depressing

down and out on the hook to clear

retention tab.

Step 1-2. Rotate the load lever to fully open po-

sition at approximately 135 degrees.

Step 1-3. Rotate the load plate to fully open po-

sition at approximately 100 degrees.

Step 2. Insert the 775-LAND CPU:

Step 2-1. Hold the CPU by the edges where are

marked with black lines.

Step 2-2. Orient the CPU with IHS (Integrated

Heat Sink) up. Locate Pin1 and the two

orientation key notches.

For proper inserting, please ensure to match the two orientation key

notches of the CPU with the two alignment keys of the socket.

Step 2-3. Carefully place the CPU into the socket

by using a purely vertical motion.

Step 2-4. Verify that the CPU is within the socket

and properly mated to the orient keys.

Step 3. Remove PnP Cap (Pick and Place Cap):

Use your left hand index finger and thumb to

support the load plate edge, engage PnP cap

with right hand thumb and peel the cap from the

socket while pressing on center of PnP cap to

assist in removal.

black line

775-Pin Socket

Pin1

alignment key

Pin1

orientation

key notch

orientation

key notch

775-LAND CPU

1515

15

ASRock Motherboard

1. It is recommended to use the cap tab to handle and avoid kicking

off the PnP cap.

2. This cap must be placed if returning the motherboard for after

service.

Step 4. Close the socket:

Step 4-1. Rotate the load plate onto the IHS.

Step 4-2. While pressing down lightly on load

plate, engage the load lever.

Step 4-3. Secure load lever with load plate tab

under retention tab of load lever.

2.22.2

2.2

Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

Installation of CPU Fan and Heatsink

For proper installation, please kindly refer to the instruction manuals of your CPU fan

and heatsink.

Below is an example to illustrate the installation of the heatsink for 775-LAND CPU.

Step 1. Apply thermal interface material onto center

of IHS on the socket surface.

Step 2. Place the heatsink onto the socket. Ensure

fan cables are oriented on side closest to the

CPU fan connector on the motherboard

(CPU_FAN1, see page 2/3, No. 2).

Step 3. Align fasteners with the motherboard

throughholes.

Step 4. Rotate the fastener clockwise, then press

down on fastener caps with thumb to install

and lock. Repeat with remaining fasteners.

If you press down the fasteners without rotating them clockwise,

the heatsink cannot be secured on the motherboard.

Step 5. Connect fan header with the CPU fan

connector on the motherboard.

Step 6. Secure excess cable with tie-wrap to ensure

cable does not interfere with fan operation or

contact other components.

EnglishEnglish

English

1616

16

ASRock Motherboard

EnglishEnglish

English

1. If you want to install two memory modules, for optimal compatibil-

ity and reliability, it is recommended to install them in the slots of

the same color. In other words, install them in the set of green

slots (DDR3_A1 and DDR3_B1), in the set of yellow slots

(DDRII_A1 and DDRII_B1), or in the set of orange slots (DDRII_A2

and DDRII_B2).

2.3 Installation of Memor2.3 Installation of Memor

2.3 Installation of Memor

y Modules (DIMM)y Modules (DIMM)

y Modules (DIMM)

This motherboard provides four 240-pin DDR2 (Double Data Rate 2) DIMM slots and

two 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel

Memory Technology. For dual channel configuration, you always need to install

identical (the same brand, speed, size and chip-type) DDR2/DDR3 DIMM pair in

the slots of the same color. In other words, you have to install identical DDR2

DIMM pair in Dual Channel A (DDRII_A1 and DDRII_B1; Yellow slots; see p.2/3

No.5), identical DDR2 DIMM pair in Dual Channel B (DDRII_A2 and DDRII_B2;

Orange slots; see p.2/3 No.6), or identical DDR3 DIMM pair in Dual Channel C

(DDR3_A1 and DDR3_B1; Green slots; see p.2/3 No.7), so that Dual Channel Memory

Technology can be activated. This motherboard also allows you to install four DDR2

DIMMs for dual channel configuration, and please install identical DDR2 DIMMs in

all four slots. You may refer to the Dual Channel Memory Configuration Table below.

Dual Channel DDR2 Memory Configurations

(DS: Double Side, SS: Single Side)

DDRII_A1 DDRII_A2 DDRII_B1 DDRII_B2

(Yellow Slot) (Orange Slot) (Yellow Slot) (Orange Slot)

2 memory modules SS X SS X

2 memory modules DS X DS X

2 memory modules X SS X SS

2 memory modules X DS X DS

4 memory modules SS SS SS SS

4 memory modules DS DS DS DS

DDR3_A1 DDR3_B1

(Green Slot) (Green Slot)

2 memory modules SS SS

2 memory modules DS DS

Dual Channel DDR3 Memory Configurations

(DS: Double Side, SS: Single Side)

1717

17

ASRock Motherboard

EnglishEnglish

English

Installing a DIMMInstalling a DIMM

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the slot

at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

2. If only one memory module or three memory modules are in-

stalled in the DDR2 DIMM slots on this motherboard, it is unable to

activate the Dual Channel Memory Technology. If only one memory

module is installed in the DDR3 DIMM slots on this motherboard,

it is unable to activate the Dual Channel Memory Technology.

3. If a pair of memory modules is NOT installed in the same Dual

Channel, for example, installing a pair of memory modules in

DDRII_A1 and DDRII_B2, it is unable to activate the Dual Channel

Memory Technology .

4. It is not allowed to install a DDR3 memory module into DDR2 slot

or install a DDR2 memory module into DDR3 slot; otherwise, this

motherboard and DIMM may be damaged.

5. DDR2 and DDR3 memory modules cannot be installed on this

motherboard at the same time.

1818

18

ASRock Motherboard

EnglishEnglish

English

2.4 Expansion Slots (PCI and PCI Express Slots)2.4 Expansion Slots (PCI and PCI Express Slots)

2.4 Expansion Slots (PCI and PCI Express Slots)

There are 3 PCI slots and 4 PCI Express slots on this motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

PCIE slots: PCIE1/DE (PCIE x1 slot; White) is used for PCI Express cards with x1

lane width cards, such as Gigabit LAN card, SATA2 card and ASRock

PCIE_DE card.

PCIE2 (PCIE x16 slot; Green) is used for PCI Express cards with x16

lane width graphics cards.

PCIE3 / PCIE4 (PCIE x1 slot; White) is used for PCI Express cards with

x1 lane width cards, such as Gigabit LAN card, SATA2 card, etc.

If you want to use ASRock DeskExpress function on this motherboard,

please install ASRock PCIE_DE card on PCIE1/DE slot.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power supply

is switched off or the power cord is unplugged. Please read the documentation

of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the bracket facing the slot that you intend to use. Keep the screws

for later use.

Step 3. Align the card connector with the slot and press firmly until the card is com-

pletely seated on the slot.

Step 4. Fasten the card to the chassis with screws.

1919

19

ASRock Motherboard

2.5 Jumpers Setup2.5 Jumpers Setup

2.5 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is

placed on these 2 pins.

Jumper Setting Description

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2/3 No. 1) +5VSB (standby) for PS/2

or USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

Clear CMOS Jumper

(CLRCMOS1)

(see p.2, No. 24 or p.3, No. 23)

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord from the power supply.

After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1

for 5 seconds. However, please do not clear the CMOS right after you update the

BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you

must boot up the system first, and then shut it down before you do the clear-

CMOS action.

Short Open

Clear CMOSDefault

EnglishEnglish

English

FSB1 Jumper

(FSB1, 3-pin jumper, see p.2 No. 34 or p.3, No. 33)

FSB2 Jumper

(FSB2, 5-pin jumper, see p.2/3 No. 9)

FSB3 Jumper

(FSB3, 5-pin jumper, see p.2/3 No. 9)

Default

2020

20

ASRock Motherboard

the red-striped side to

Pin1

EnglishEnglish

English

2.6 Onboard Headers and Connectors2.6 Onboard Headers and Connectors

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper

caps over the headers and connectors will cause permanent dam-

age of the motherboard!

FDD connector

(33-pin FLOPPY1)

(see p.2 No. 25 or p.3 No. 24)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

If you want to overclock the CPU you adopt to FSB1066 on this motherboard, you need

to adjust the jumpers. Please short pin4, pin5 for FSB2 jumper and pin4, pin5 for FSB3

jumper. Otherwise, the CPU may not work properly on this motherboard. Please refer to

below jumper settings.

If you want to overclock the CPU you adopt to FSB1333 on this motherboard, you need

to adjust the jumpers. Please short pin3, pin4 for FSB2 jumper and pin4, pin5 for FSB3

jumper. Otherwise, the CPU may not work properly on this motherboard. Please refer to

below jumper settings.

If you want to overclock the CPU you adopt to FSB1600 on this motherboard, you need

to adjust the jumpers. Please short pin3, pin4 for FSB2 jumper and pin3, pin4 for FSB3

jumper. Otherwise, the CPU may not work properly on this motherboard. Please refer to

below jumper settings.

When you mount a FSB800 or FSB1066 CPU, and try to overclock to FSB1333 or

FSB1600 (by BIOS setting) you may face the problem, that DRAM frequency will be

overclocked very high. Please use jumper to force NB to be strapped at higher

frequency, so the DRAM can work at lower frequency.

La page charge ...

ASROCK P43TWINS Le manuel du propriétaire

Ce manuel convient également à

ASROCK P43TWINS Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents