Panasonic PT-L785U Manuel utilisateur

Marque: Panasonic

Modèle: PT-L785U

Catégorie: Projecteurs de données

Taper: Manuel utilisateur

Ce manuel convient également à

PTL785U

ENGLISH

Before operating this product, please read the instructions carefully and save this

manual for future use.

LCD Projector

Operating Instructions

Model No. PT-L785U

TQBJ 0150

Commercial Use

VIDEO

RGB

ALL SET

2-ENGLISH

IMPORTANT SAFETY NOTICE

Dear Panasonic Customer:

This instruction booklet provides all the necessary operating information that you

might require. We hope it will help you to get the most out of your new product,

and that you will be pleased with your Panasonic LCD projector.

The serial number of your product may be found on its bottom. You should note

it in the space provided below and retain this booklet in case service is required.

Model number: PT-L785U

Serial number:

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the product.

Power Supply: This LCD Projector is designed to operate on 100 V – 240 V, 50 Hz/60

Hz AC, house current only.

CAUTION: The AC power cord which is supplied with the projector as an accessory can

only be used for power supplies up to 125 V, 7 A. If you need to use higher

voltages or currents than this, you will need to obtain a separate 250 V

power cord. If you use the accessory cord in such situations, fire may result.

CAUTION:

This equipment is equipped with a three-pin grounding-type power

plug. Do not remove the grounding pin on the power plug. This

plug will only fit a grounding-type power outlet. This is a safety

feature. If you are unable to insert the plug into the outlet, contact

an electrician. Do not defeat the purpose of the grounding plug.

Do not remove

ENGLISH-3

Preparation

WARNING:

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

FCC CAUTION: To assure continued compliance, use only shielded

interface cables when connecting to computers or

peripheral devices.

Any unauthorized changes or modifications to this

equipment will void the users authority to operate.

WARNING:

B Not for use in a computer room as defined in the Standard for the

Protection of Electronic Computer/Data Processing Equipment,

ANSI/NFPA 75.

Declaration of Conformity

Model Number: PT-L785U

Trade Name: Panasonic

Responsible party: Matsushita Electric Corporation of America.

Address: One Panasonic Way Secaucus New Jersey 07094

Telephone number: 1-800-528-8601 or 1-800-222-0741

Email: [email protected]

This device complies with Part 15 of the FCC Rules, Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

4-ENGLISH

Contents

Preparation

IMPORTANT SAFETY NOTICE ...2

Precautions with regard to safety

...5

Accessories .................................9

Before use ..................................10

Location and function of each part

...12

Getting started

Setting-up...................................18

Projection methods, Projector

position, Projection distances

Connections...............................20

Connecting to video equipment,

Connecting to computer

Preparation for the remote

control unit..............................22

Setting the projector ID number

for remote control unit ...........23

Basic operation

Turning on the power................24

Turning off the power................26

Useful functions

Correcting the image position

automatically...........................28

Turning off the picture and sound

momentarily ............................29

Pausing a picture.......................29

Enlarging the picture.................30

Adjusting the volume ................30

Adjusting the zoom and focus ...31

Useful functions of the remote

control unit..............................32

Laser beam pointer, Wireless mouse

Adjustments and settings

On-screen menus ......................34

Menu screens, Menu operation guide,

Returning a setting to the factory default

Adjusting the picture.................39

PICTURE MODE, CONTRAST,

BRIGHT, COLOR, TINT, SHARPNESS,

COLOR TEMP., Noise Reduction (NR),

WHITE BALANCE R/G/B, TV-SYSTEM,

Projecting sRGB-compatible pictures

Adjusting the position...............42

POSITION, DOT CLOCK, CLOCK

PHASE, KEYSTONE, OSD

POSITION, ASPECT, RESIZING,

AUTO SETUP, FRAME LOCK

Audio adjustment ......................46

VOLUME, MUTE

Changing the display language

...46

Option settings ..........................47

OSD, AUTO SEARCH, AUTO SIGNAL, RGB2

SELECT, RGB/YP

BPR, VGA60/480p, BACK

COLOR, CINEMA REALITY, FRONT/REAR,

DESK/CEILING, FAN CONTROL, LAMP

POWER, LAMP RUN TIME, FUNC 1,

CONTROL KEY, AUTO POWER OFF, SET ID

Adjusting the lens .....................50

ZOOM/FOCUS, LENS SELECT

Network setup............................50

Setting up the security function

...51

PASSWORD SETTING, CHANGE

PASSWORD, TEXT DISPLAY,

CHANGE TEXT, LOGO DISPLAY,

LOGO CLEAR, LOGO CAPTURE

Care and maintenance

When the TEMP indicator and the

LAMP indicator are illuminated

...54

Cleaning and replacing the air filter

...56

Replacing the lamp unit ............57

Before calling for service..........60

Cleaning and maintenance .......61

Others

Using the cable cover ...............62

Putting the mains lead and remote

control unit away, Covering the

connector panel

Replacing the projection lens ...64

Projection distance for each

projection lens (sold separately)

Specifications ............................68

Appendix ....................................70

List of compatible signals, Using the

REMOTE connector, Using the SERIAL

connector, Pin assignments, Projection

dimensions calculation methods

Dimensions ................................76

Trademark acknowledgements

...76

NOTES IMPORTANTES

CONCERNANT LA SECURITE

Précautions de sécurité

.............

Avant l’utilisation

.........................

Remplacement du bloc de lampe

...

ENGLISH-5

Preparation

Precautions with regard to safety

WARNING

If you notice smoke, strange smells or noise coming from the projector,

disconnect the power cord plug from the wall outlet.

B Do not continue to use the projector in such cases, otherwise fire or

electric shocks could result.

B Check that no more smoke is coming out, and then contact an Authorized

Service Center for repairs.

B Do not attempt to repair the projector yourself, as this can be dangerous.

Do not install this projector in a place which is not strong enough to

take the full weight of the projector.

B If the installation location is not strong enough, it may fall down or tip over,

and severe injury or damage could result.

Installation work (such as ceiling suspension) should only be carried

out by a qualified technician.

B If installation is not carried out correctly, there is the danger that injury or

electric shocks may occur.

If foreign objects or water get inside the projector, or if the projector is

dropped or the cabinet is broken, disconnect the power cord plug from

the wall outlet.

B Continued use of the projector in this condition may result in fire or electric

shocks.

B Contact an Authorized Service Center for repairs.

Do not overload the wall outlet.

B If the power supply is overloaded (for example, by using too many

adapters), overheating may occur and fire may result.

Do not remove the cover or modify it in any way.

B High voltages can cause fire or electric shocks.

B For any inspection, adjustment and repair work, please contact an

Authorized Service Center.

Clean the power cord plug regularly to prevent it from becoming

covered in dust.

B If dust builds up on the power cord plug, the resulting humidity can

damage the insulation, which could result in fire. Pull the power cord plug

out from the wall outlet and wipe it with a dry cloth.

B If not using the projector for an extended period of time, pull the power

cord plug out from the wall outlet.

6-ENGLISH

Do not do anything that might damage the power cord or the power cord

plug.

B Do not damage the power cord, make any modifications to it, place it near

any hot objects, bend it excessively, twist it, pull it, place heavy objects on

top of it or wrap it into a bundle.

B If the power cord lead is used while damaged, electric shocks, short-

circuits or fire may result.

B Ask an Authorized Service Center to carry out any repairs to the power

cord that might be necessary.

Do not handle the power cord plug with wet hands.

B Failure to observe this may result in electric shocks.

Insert the power cord plug securely into the wall outlet.

B If the plug is not inserted correctly, electric shocks or overheating could

result.

B Do not use plugs which are damaged or wall outlets which are coming

loose from the wall.

Do not place the projector on top of surfaces which are unstable.

B If the projector is placed on top of a surface which is sloped or unstable, it

may fall down or tip over, and injury or damage could result.

Do not place the projector into water or let it become wet.

B Failure to observe this may result in fire or electric shocks.

Do not place liquid containers on top of the projector.

B If water spills onto the projector or gets inside it, fire or electric shocks

could result.

If any water gets inside the projector, contact an Authorized Service Center

Do not insert any foreign objects into the projector.

B Do not insert any metal objects or flammable objects into the projector or

drop them onto the projector, as doing so can result in fire or electric

shocks.

Keep the batteries out of the reach of infants.

B If the batteries are swallowed, death by suffocation may result. If you

believe that the batteries may have been swallowed, seek medical advice

immediately.

Do not allow the + and - terminals of the batteries to come into contact

with metallic objects such as necklaces or hairpins.

B Failure to observe this may cause the batteries to leak, overheat, explode

or catch fire.

B Store the batteries in a plastic bag and keep them away from metallic

objects.

During a thunderstorm, do not touch the projector or the cable.

B Electric shocks can result.

Do not use the projector in a bath or shower.

B Fire or electric shocks can result.

ENGLISH-7

Preparation

Do not look into the lens while the projector is being used.

B Strong light is emitted from the projector’s lens. If you look directly into this

light, it can hurt and damage your eyes.

B Be especially careful not to let young children look into the lens. In

addition, turn off the power and disconnect the power cord plug when you

are away from the projector.

Keep the remote control unit out of the reach of children, and do not

look into the laser beam or point it towards other people.

B If the laser beam which is emitted by the remote control unit transmitter is

pointed directly into the eyes, it may cause visual ability to be impaired.

Do not place your hands or other objects close to the air outlet port.

B Heated air comes out of the air outlet port. Do not place your hands or

face, or objects which cannot withstand heat close to this port, otherwise

burns or damage could result.

Replacement of the lamp unit should only be carried out by a qualified

technician.

B The lamp unit has high internal pressure. If improperly handled, explosion

might result.

B The lamp unit can easily become damaged if struck against hard objects

or dropped, and injury or malfunctions may result.

When replacing the lamp, allow it to cool for at least one hour before

handling it.

B The lamp cover gets very hot, and contact with it can cause burns.

Before replacing the lamp, be sure to disconnect the power cord plug

from the wall outlet.

B Electric shocks or explosions can result if this is not done.

Caution

Do not cover the air inlet port or the air outlet port.

B Doing so may cause the projector to overheat, which can cause fire or

damage to the projector.

B Do not place the projector in narrow, badly ventilated places such as

closets or bookshelves.

Do not set up the projector in humid or dusty places or in places where

the projector may come into contact with smoke or steam.

B Using the projector under such conditions may result in fire or electric shocks.

When disconnecting the power cord, hold the plug, not the lead.

B If the power cord itself is pulled, the lead will become damaged, and fire,

short-circuits or serious electric shocks may result.

Always disconnect all cables before moving the projector.

B Moving the projector with cables still attached can damage the cables,

which could cause fire or electric shocks to occur.

8-ENGLISH

Do not place any heavy objects on top of the projector.

B Failure to observe this may cause the projector to become unbalanced

and fall, which could result in damage or injury.

Do not short-circuit, heat or disassemble the batteries or place them

into water or fire.

B Failure to observe this may cause the batteries to overheat, leak, explode

or catch fire, and burns or other injury may result.

When inserting the batteries, make sure the polarities (+ and -) are

correct.

B If the batteries are inserted incorrectly, they may explode or leak, and fire,

injury or contamination of the battery compartment and surrounding area

may result.

Use only the specified batteries.

B If incorrect batteries are used, they may explode or leak, and fire, injury or

contamination of the battery compartment and surrounding area may

result.

Do not mix old and new batteries.

B If the batteries are inserted incorrectly, they may explode or leak, and fire,

injury or contamination of the battery compartment and surrounding area

may result.

Insulate the battery using tape or similar before disposal.

B If the battery comes into contact with metallic objects or other batteries, it

may catch fire or explode.

Do not put your weight on this projector.

B You could fall or the projector could break, and injury may result.

B Be especially careful not to let young children stand or sit on the projector.

Do not lift up the projector by holding the cable cover.

B Failure to observe this may cause the cable cover to come off and the

projector might fall, which could result in injury.

Disconnect the power cord plug from the wall outlet as a safety

precaution before carrying out any cleaning.

B Electric shocks can result if this is not done.

Ask an Authorized Service Center to clean inside the projector at least

once a year.

B If dust is left to build up inside the projector without being cleaned out, it

can result in fire or problems with operation.

B It is a good idea to clean the inside of the projector before the season for

humid weather arrives. Ask your nearest Authorized Service Center to

clean the projector when required. Please discuss with the Authorized

Service Center regarding cleaning costs.

We are constantly making efforts to preserve and maintain a clean

environment. Please take non repairable units back to your dealer or a

recycling company.

ENGLISH-9

Preparation

Remote control unit

(N2QAEA000022 x1)

AAA batteries for

remote control unit (x2)

RGB signal cable

[3.0 m (9´10˝),

K1HB15FA0001 x1]

Accessories

Check that all of the accessories shown below have been included with your

projector.

VIDEO

RGB

ALL SET

Power cord

(K2CG3FZ00008 x 1)

Cable cover

(TXFKR01VJX7 x1)

NOTICE:

B This product has a High Intensity Discharge (HID) lamp that contains a

small amount of mercury. It also contains lead in some components.

Disposal of these materials may be regulated in your community due to

environmental considerations. For disposal or recycling information

please contact your local authorities, or the Electronics Industries

Alliance: <http://www.eiae.org.>

10-ENGLISH

Before use

Caution when moving the projector

Be sure to attach the lens cover before moving the projector.

The projection lens is extremely susceptible to vibration and shocks. Be

careful not to subject it to excessive vibration and shock when moving the

projector.

Cautions regarding setting-up

Avoid setting up in places which are subject to vibration or shocks.

The internal parts can be damaged, which may cause malfunctions or

accidents.

Do not set up the projector near high-voltage power lines or near

motors.

The projector may be subject to electromagnetic interference.

If installing the projector to the ceiling, ask a qualified technician to

carry out all installation work.

You will need to purchase the separate installation kit (Model No.ET-PK780).

Furthermore, all installation work should only be carried out by a qualified

technician.

If using this projector at high elevations (above 1 400 m), set the “FAN

CONTROL” to “HIGH”. (Refer to page 48.)

Failure to observe this may result in malfunctions.

ENGLISH-11

Preparation

Notes on use

In order to get the best picture quality

Draw curtains or blinds over any windows and turn off any lights near the

screen to prevent outside light or light from indoor lamps from shining onto

the screen.

Do not touch the surfaces of the lens with your bare hands.

If the surface of the lens becomes dirty from fingerprints or anything else, this

will be magnified and projected onto the screen. Moreover, when not using

the projector, retract the lens and then cover it with the lens cover.

Screen

Do not apply any volatile substances which may cause discoloration to the

screen, and do not let it become dirty or damaged.

Lamp

The lamp may need to be replaced earlier due to variables such as individual

lamp characteristics, usage conditions and the installation environment,

especially when the projector is subjected to continuous use for more than

10 hours or the power is frequently turned on and off, as the operations that

prevent blackening of the bulb (the action of the halogen cycle) do not work

enough during short periods of time.

Liquid crystal panel

The liquid crystal panel of the projector is built with very high precision

technology to provide fine picture details. Occasionally, a few non-active

pixels may appear on the screen as fixed points of blue, green or red.

Please note that this does not affect the performance of your LCD.

12-ENGLISH

Location and function of each part

Projector <Top, right and front>

)

,-.

(

# Projector control panel (page 14)

$ Speaker

% Connector panel (page 16)

& MAIN POWER switch (pages 24 and 26)

' Power input socket (AC IN) (page 24)

The accessory power cord is connected here.

Do not use any power cord other than the accessory power cord.

( Air inlet ports

Do not cover these ports.

) Air filter (page 56)

* Front adjustable legs(L/R) (page 25)

+ Leg adjuster buttons(L/R) (page 25)

These buttons are used to unlock the front adjustable legs. Press to adjust

the angle of tilt of the projector.

, Remote control signal receptor (page 22)

- Focus ring (page 25)

. Lens cover

/ Projection lens

0 Lens release button (page 64)

This button is used when using a projection lens that is sold separately.

ENGLISH-13

Preparation

# Remote control signal receptor (page 22)

$ Lamp unit holder (page 57)

% Air outlet port

Do not cover this port.

& Carrying handle

' Security lock

This can be used to connect a commercially-available theft-prevention

cable (manufactured by Kensington). This security lock is compatible with

the Microsaver Security System from Kensington.

WARNING

Do not place your hands or other objects close to the air outlet port.

B Heated air comes out of the air outlet port. Do not place your hands or

face, or objects which cannot withstand heat close to this port, otherwise

burns or damage could result.

Projector <Back and bottom>

NOTE:

B During projection of an image, the cooling fan will operate, emitting a

small noise as it operates. Turning the lamp on or off will cause this

noise to increase a little.

B By using the “OPTION” menu to set “LAMP POWER” to “LOW”, the

operating sound of the fan can be reduced. (Refer to page 48.)

#$%

14-ENGLISH

Remote control unit

RGBVIDEOAUTO SETUP

ON(G)

STANDBY(R)

ENTER

POWER

SHUTTER

INPUT

TEMP

LAMPRGB INPUT

– FOCUS +

–

ZOOM +

VIDEO

RGB

ALL SET

)

(

)

(

;

# Power indicator (pages 24, 26 and 27)

This indicator illuminates red when the MAIN POWER switch is turned on,

and illuminates green when the power is turned on and a picture starts to

be projected.

When the projector is in “WEB STANDBY” mode, this indicator flashes slowly

in red.

$ RGB INPUT indicator (page 27)

This indicator illuminates when a signal is input into the connector that is

selected with the input select buttons.

% LAMP indicator (page 55)

This indicator illuminates when it is time to replace the lamp unit. It flashes

if a circuit abnormality is detected.

& INPUT (RGB, VIDEO) buttons (page 25)

These buttons are used to select the input signals. When “AUTO SEARCH” in the

“OPTION” menu is set to “ON”, the input signal will be detected and selected

automatically by pressing this button for a few seconds. (Refer to page 47.)

' TEMP indicator (page 54)

This indicator illuminates if an abnormally high temperature is detected inside

the projector or around it. If the temperature rises above a certain level, the

power supply will be turned off automatically and the indicator will flash.

( SHUTTER button (page 29)

This button is used to momentarily turn off the picture and sound.

) ENTER button (page 38)

This button is used to accept and to activate items selected in the on-

screen menus.

Projector control panel

ENGLISH-15

Preparation

*When in computer operating mode, this button on the remote control unit

functions differently. (page 33)

* Arrow (

FFGGII

and

) buttons (page 37)

These buttons are used to select and adjust items in the on-screen menus.

*When in computer operating mode, these buttons on the remote control

unit function differently. (page 33)

+ MENU button (pages 34 and 37)

This button is used to display the menu screens. When a menu screen is

being displayed, this button can be used to return to a previous screen or

to clear the screen.

, ZOOM +/- buttons (page 25)

These buttons are used to adjust the size of the projected image.

- FOCUS +/- buttons (page 25)

These buttons are used to adjust the focus of the projected image.

. AUTO SETUP button (pages 25 and 28)

If this button is pressed while a picture is being projected, the projection settings

will be adjusted automatically in accordance with the signal being input.

/ POWER button (pages 24 and 26)

These buttons are used to turn the power on and off when MAIN POWER

is turned on.

(For the remote control unit, the “ ” button is for turning on the power and

the “ ” button is for turning off the power.)

0 Laser emitter (page 32)

1 Infrared emitter (page 22)

2 Click button (page 33)

This button can be used when the operating mode select switch is moved

to the left (Computer).

3 STD (standard) button (page 38)

This button is used to reset the projector adjustment values to the factory

default settings.

4 FUNC1 button (pages 43, 46 and 49)

This button can be used for 1) switching on and off the sound volume and

2) entering into the keystone distortion correction mode. Adjust “FUNC1”

in the “OPTION” menu to select which you wish to use.

5 LENS button (page 31)

This button is used to display the zoom and focus adjustment screen.

6 Operation indicator (page 32)

This indicator illuminates while a laser beam is being emitted (while the LASER

button is being pressed). It flashes when any other buttons are being pressed.

7 LASER button (page 32)

A beam of laser light is emitted while this button is being pressed. This

laser beam can be used as a pointer to point to something on the screen.

8 FREEZE button (page 29)

This button is used to momentarily freeze projection so that a still picture is displayed.

9 D.ZOOM +/- buttons (page 30)

These buttons are used to enlarge the projected image.

(continued on next page)

16-ENGLISH

Connector panel

& ( )%

, - .+

# Wired LAN connector

This connector is used to connect a personal computer to the projector in

order to externally control the projector. (10 Base-T/100 Base-TX)

Refer to the “Network Function Edition” operating instructions for details.

$ SERIAL connector (pages 20, 21 and 72)

This connector is used to connect a personal computer to the projector in

order to externally control the projector. (RS-232C compatible)

% RGB1 IN connector (pages 20 and 21)

This connector is used to input RGB signals and YPBPR signals.

: VOLUME +/- buttons (page 30)

These buttons are used to adjust the volume of the sound that is output

from the projector’s built-in speakers and AUDIO OUT connector. Refer to

page 46 for details on how to adjust the volume using the buttons on the

projector control panel.

; ID SET/ALL button (page 23)

These buttons are used to set the projector ID number into the remote

control unit when using multiple projectors with a single remote control

unit.

< Operating mode (Computer, Projector) select switch (page 33)

Move this switch to the left side to use the remote control unit to operate a

computer, and move it to the right side to operate the projector.

(continued from previous page)

ENGLISH-17

Preparation

& RGB2 IN/RGB OUT connector (pages 20, 21 and 47)

This connector is used to input or output RGB signals and YPBPR signals.

Adjust “RGB2 SELECT” in the “OPTION” menu to select whether you want

input or output with this connector.

' DVI-D IN connector (page 21)

This connector is used to input DVI-D signals.

( AUDIO OUT connector (pages 20 and 21)

This connector is used to output the audio signals which are input to the

projector. If audio equipment is connected to this connector, no sound will

be output from the built-in speakers.

) S-VIDEO IN connector (pages 20 and 45)

This connector is used to input signals from a S-VIDEO-compatible

equipment such as a video deck. The connector is S1 signal compatible,

and it automatically switches between 16:9 and 4:3 aspect ratios in

accordance with the type of signal being input.

* AUDIO IN L-R connectors (for S-VIDEO/VIDEO) (page 20)

Only one system is provided, so connect the appropriate connectors when

using S-VIDEO or VIDEO.

+ REMOTE connector (page 71)

This connector is used to control the projector from the remote control set

up in wired mode.

, RGB3 IN connector (pages 20 and 21)

This connector is used to input RGB signals and YPBPR signals.

- RGB AUDIO IN connector (pages 20 and 21)

Only one system is provided, so connect the appropriate connector when

using RGB1, RGB2 or RGB3.

. VIDEO IN connector (page 20)

This connector is used to input video signals from a video equipment such

as a video deck.

18-ENGLISH

Setting-up

Projection methods

In way of installing projector, any one of the following four projection methods

are used. Select whichever projection method matches the setting-up

method. (The projection method can be set from the “OPTION” menu. Refer

to page 48 for details.)

BFront-desk projection BFront-ceiling projection

BRear-desk projection

(Using a translucent screen)

BRear-ceiling projection

(Using a translucent screen)

Menu items Setting

FRONT

DESK

FRONT/REAR

DESK/CEILING

Menu items Setting

FRONT

CEILING

FRONT/REAR

DESK/CEILING

Menu items Setting

REAR

DESK

FRONT/REAR

DESK/CEILING

Menu items Setting

REAR

CEILING

FRONT/REAR

DESK/CEILING

NOTE:

B You will need to purchase the separate ceiling bracket (ET-PK780)

when using the ceiling installation method.

B If you set up the projector vertically, it may cause

damage to the projector.

B It is recommended that you set up the projector

in a place that is tilted at less than

±30°. Setting

up the projector in places that are tilted at more

than

±30° may cause malfunctions.

ENGLISH-19

Getting started

25 mm

(-31/32˝)

L: Projection distance

SH: Image height

SW:Image width

Top edge of screen

Screen

Bottom edge of screen

Screen

NOTE:

B The dimensions in the table above are approximate.

B If you use the projection distance for the 16:9 screen,

the 4:3 projection image overflows the screen at the top

and bottom.

For details about projected image distances, refer to page 75.

Projector position

1.01 m(40˝) 0.61 m(2´) 0.81 m(2´8˝) 1.6 m(5´2˝) 2.0 m(6´6˝)

1.27 m(50˝) 0.76 m(2´6˝) 1.02 m(3´4˝) 2.0 m(6´6˝) 2.6 m(8´6˝)

1.52 m(60˝) 0.91 m(3´) 1.22 m(4´) 2.4 m(7´10˝) 3.1 m(10´2˝)

1.77 m(70˝) 1.07 m(3´6˝) 1.42 m(4´8˝) 2.8 m(9´2˝) 3.6 m(11´9˝)

2.03 m(80˝) 1.22 m(4´) 1.63 m(5´4˝) 3.2 m(10´5˝) 4.2 m(13´9˝)

2.28 m(90˝) 1.37 m(4´6˝) 1.83 m(6´) 3.6 m(11´9˝) 4.7 m(15´5˝)

2.54 m(100˝) 1.52 m(5´) 2.03 m(6´8˝) 4.0 m(13´1˝) 5.3 m(17´4˝)

3.81 m(150˝) 2.29 m(7´6˝) 3.05 m(10´) 6.1 m(20´) 7.9 m(25´11˝)

5.08 m(200˝) 3.05 m(10´) 4.06 m(13´4˝) 8.1 m(26´6˝) 10.6 m(34´9˝)

6.35 m(250˝) 3.81 m(12´6˝) 5.08 m(16´8˝) 10.1 m(33´1˝) 13.3 m(43´7˝)

7.62 m(300˝) 4.57 m(15´) 6.10 m(20´) 16.0 m(52´5˝)

Projection distances*

Screen size (4:3)

Diagonal

length

Height

(SH)

Width

(SW)

Projection distance (L)

Wide

(LW)

Telephoto

(LT)

12.2 m(40´)

*For standard lens which is supplied with the projector. Refer to pages 65 –

67 for details on the projection distances for the optional lenses.

20-ENGLISH

Connections

Notes on connections

Read the instruction manual for each peripheral device carefully before connecting it.

Turn off the power supply for all peripheral devices before making any connections.

If the cables necessary for connection are not included with the peripheral device or

available as an option, you may need to prepare a proper cable for the device concerned.

If there is a lot of jitter in the video signal, the projected image may flicker. In such

cases, it will be necessary to connect a TBC (time base corrector).

Refer to the list on page 70 for details on compatible signals which can be input to

the projector.

Only one audio system circuit is available for each of the AUDIO IN L-R connectors for

S-VIDEO/VIDEO signals and the RGB AUDIO IN connector, so if you wish to change

the audio input source, you will need to remove and insert the appropriate plugs.

Connecting to video equipment

D-sub 15-pin (male) - BNCx5 (male) adapter cable

Red (connect to PR signal connector)

Blue (connect to PB signal connector)

Green (connect to Y signal connector)

D-sub 9-pin

(male)

DVD player Audio system

Video deck

Computer for

control use

DVD player

Red (connect to PR signal connector)

Blue (connect to PB signal connector)

Green (connect to Y signal connector)

DVD player

(with component

video connectors)

BNC/RCA adapter

NOTE:

B If the signal cables are disconnected or if the power supply for the

computer or video deck is turned off while “D.ZOOM”(digital zoom) is

being used, this function will be cancelled.

La page charge ...

Panasonic PT-L785U Manuel utilisateur

Marque: Panasonic

Modèle: PT-L785U

Catégorie: Projecteurs de données

Taper: Manuel utilisateur

Ce manuel convient également à

PTL785U

Télécharger le PDF

rapport

dans d''autres langues

English: Panasonic PT-L785U User manual

Panasonic PT-L785U Manuel utilisateur

Ce manuel convient également à

Panasonic PT-L785U Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents