ZyXEL NWA1100 Guide de démarrage rapide

www.zyxel.com

QUICK START GUIDE

NWA1100

802.11g Business WLAN

Access Point

Firmware v1.00

Edition 1, 12/2009

DEFAULT LOGIN DETAILS

IP Address: http://192.168.1.2

Password: 1234

CONTENTS

ENGLISH 3

DEUTSCH 19

ESPAÑOL 35

FRANÇAIS 51

ITALIANO 67

РУССКИЙ 83

SVENSKA 99

简体中文

115

繁體中文

129

C

2

Front and Base Panels

ENGLISH

3

Overview

This Quick Start Guide shows how to set up and configure the NWA1100

(marked Z in the figure) to allow wireless clients to securely access your

wired network. See your User’s Guide for more information.

You may need your Internet access information.

To set up your wireless network you need to:

• Connect the Hardware

• Access the Web Configurator

• Configure the NWA1100

• Install the Hardware

• Set Up Power over Ethernet (Optional)

Z

ENGLISH

4

Connect the Hardware

1. Using the grey Ethernet cable, connect the ETHERNET port to a computer

for initial configuration.

2. Connect the POWER 12VDC socket to a power source using only the

included power adaptor.

Connect the NWA1100’s ETHERNET port to an Ethernet jack with

network access after you have completed the initial configuration.

ENGLISH

5

LEDs

• The SYS LED blinks amber, then turns steady green when the power is

connected.

• One of the LEDs by the ETHERNET port turns on if the port is properly

connected, and blinks when there is traffic. The amber light shines if the

connection is at 100 Mbps. The green light shines if the connection is at

10Mbps.

 If neither LED near the ETHERNET port turns on, check the cable

connections to the port. Ensure your computer’s network card is

working properly.

ENGLISH

6

Access the Web Configurator

Use Internet Explorer 6.0 and later or Netscape Navigator 7.0 and later

versions with JavaScript enabled and pop-up blocking disabled.

Set Up Your Computer’s IP Address

Note down your computer’s current IP settings before you change

them.

First, set your computer to use a static IP address in the 192.168.1.3 -

192.168.1.254 range with a subnet mask of 255.255.255.0. This ensures that

your computer can communicate with your NWA1100. See your User’s Guide

for information on setting up your computer’s IP address.

ENGLISH

7

Log Into the Web Configurator

Even though you can connect to the NWA1100 wirelessly, it is

recommended that you connect your computer to the ETHERNET port

for initial configuration.

1. Launch your web browser.

Enter 192.168.1.2 (the

NWA1100’s default IP address)

as the address.

 If you cannot access the Web configurator, make sure the IP

addresses and subnet masks of the NWA1100 and the computer

are in the same IP address range.

2. Enter 1234 (the default

password) in the Password

field and click Login.

ENGLISH

8

3. Change the login password by

entering a new password and

clicking Apply. Be sure to

record the new password and

keep it in a safe place.

 If you change the password and then forget it, you will need to

reset the NWA1100. Refer to the User’s Guide for how to use the

RESET button.

4. The STATUS screen appears.

ENGLISH

9

Configure the NWA1100

Configure System Settings

1. Click SYSTEM in the navigation panel.

2. The SYSTEM > General screen appears.

ENGLISH

10

System Name is for identifying the NWA1100 on your network. Choose a

distinctive name, or leave this at its default.

DNS Server(s): if your ISP gave you specific DNS (Domain Name

System) settings, select User-Defined and enter them here. Otherwise,

leave these fields at their defaults.

3. Click Apply.

ENGLISH

11

Configure Wireless Settings

1. Click WIRELESS

in the navigation

panel. The

Wireless

Settings screen

displays.

The wireless stations and the NWA1100 must use the same SSID,

channel ID and encryption settings for wireless communication.

Operation Mode: Ensure that AP mode is selected.

Wireless Mode: Select the wireless standard you want your network to

use. If you are not sure which to select, select 802.11b+g.

Channel: Select the wireless channel you want your network to use.

2. Click Apply to save your settings.

ENGLISH

12

3. Click the

Security tab. If

you don’t

configure

wireless security,

anyone can

access your

network.

This is where you can enter the security settings for your wireless

network. The fields you fill in differ according to the type of security you

select in the Security Mode field. Select None if you do not wish to use

wireless security.

This example uses WPA2-PSK security, in which all wireless clients must

use the same pre-shared key to join the network.

Ensure that all your wireless clients support the type of security you set.

Click Apply when you have finished.

 If the wireless clients cannot communicate with the network,

ensure that the clients and the NWA1100 are using the same

wireless security settings.

ENGLISH

13

Configure IP Settings

1. You need to set your

NWA1100’s IP address to

be in the same subnet as

your network. Click IP in

the navigation panel.

Select Get automatically

from DHCP if you want to

have a DHCP server on

your network assign an IP

address to the NWA1100.

If you have a specific IP

address to use, select

Use fixed IP address

and enter it along with the

subnet mask and gateway

IP address.

Click Apply. The

NWA1100 now uses the

new IP settings; you can

no longer connect to the

NWA1100 using the

default IP address.

ENGLISH

14

The NWA1100 is now ready to connect to your switch or router. You can do

this now, or once you have attached the antennas and mounted the

NWA1100.

 If the NWA1100 cannot communicate with the network, ensure

that the NWA1100 is using an IP address on the same subnet as

the switch / router.

If you change the NWA1100’s IP address, you must use the new IP

address when you next access the web configurator. If you select Get

automatically from DHCP, check your DHCP server to determine the IP

address it assigns to the NWA1100. Refer to your DHCP server’s

documentation for more information.

2. If you changed your computer’s IP address, return it to its previous

setting.

3. Change the wireless settings in the wireless stations to match those of

the NWA1100, if necessary. Refer to your wireless adapter’s

documentation.

ENGLISH

15

Install the Hardware

Figures in this section use generic icons. The ZyXEL Device in the picture is

not an exact representation of your device.

Attaching Antennas

Hardware Mounting

In general, the best location for the access point is at the center of your

intended wireless coverage area. For better performance, mount the

NWA1100 high up in an area that is free of obstructions.

Wall-mounting

Do the following to attach your NWA1100 to a wall.

Screw the antennas clockwise onto the antenna

connectors on the sides of your NWA1100. The

antennas should be perpendicular to the ground and

parallel to each other.

Make sure the antennas are securely screwed onto the

antenna connectors.

ENGLISH

16

1. Screw the two screws provided with your NWA1100 into the wall 60mm

apart (see the figure in step 3). Use screws with 6mm ~ 8mm (0.24" ~

0.31") wide heads. Do not screw the screws all the way in to the wall;

leave a small gap between the head of the screw and the wall.

The gap must be big enough for the screw heads to slide into the screw

slots and the connection cables to run down the back of the NWA1100.

Make sure the screws are securely fixed to the wall and strong enough

to hold the weight of the NWA1100 with the connection cables.

ENGLISH

17

2. Adjust the cables.

Run the connection cables down the back of the NWA1100 as shown in

the following figure.

OR:

Run the connection cables upward and along the edge of the ceiling.

3. Align the holes on the

back of the NWA1100

with the screws on the

wall. Hang the

NWA1100 on the

screws.

6

0

m

ENGLISH

18

Set Up Power over Ethernet

(Optional)

Power over Ethernet (PoE) is the ability to provide power to your NWA1100

via an 8-pin CAT 5 Ethernet cable, eliminating the need for a nearby power

source.

A PoE injector (not included) is also needed to supply the Ethernet cable with

power. This feature allows increased flexibility in the location of your

NWA1100.

In the following figure, Z is your NWA1100, A is the CAT 5 Ethernet cable, B

is the PoE injector and C is the power cable.

ENGLISH

DEUTSCH

19

Übersicht

In dieser Kurzanleitung erfahren Sie, wie das NWA-1100 (im Beispiel unten

mit einem Z gekennzeichnet) installiert und konfiguriert wird, damit Wireless-

Clients sicher auf Ihr kabelgebundenes Netzwerk zugreifen können. Weitere

Informationen finden Sie im Benutzerhandbuch.

Halten Sie die Daten für Ihren Internetzugang bereit.

Um das Drahtlosnetzwerk einzurichten, müssen Sie:

• Anschließen der Hardware.

• Zugreifen auf den Web-Konfigurator.

• Konfigurieren des NWA-1100s.

• Installieren der Hardware.

• Power-over-Ethernet (PoE) Einrichten (Optional).

Z

DEUTSCH

ENGLISH

20

Anschließen der Hardware

1. Verbinden Sie für die Erstkonfiguration den ETHERNET-Anschluss mit

dem grauen Ethernet-Kabel mit dem Computer.

2. Verbinden Sie die 12VDC-Netzanschlussbuchse POWER des Geräts mit

dem mitgelieferten Netzadapter mit dem Stromnetz.

Nachdem Sie die Erstkonfiguration durchgeführt haben, verbinden Sie

den ETHERNET-Anschluss des NWA-1100s mit einem

Ethernetanschluss mit Netzwerkverbindung.

La page charge ...

ZyXEL NWA1100 Guide de démarrage rapide

Ce manuel convient également à

ZyXEL NWA1100 Guide de démarrage rapide

dans d''autres langues

Documents connexes