Xylem FLXI2102 Mode d'emploi

FLXI2102
Xylem
Marque
Xylem
Modèle
FLXI2102
Taper
Mode d'emploi
FlexNet® SmartPoint® Module
FOR ACLARA i210+c
QUICK GUIDE
EQG-10011-01
The Sensus FlexNet™ SmartPoint® module provides wireless
communication capability to electric utility meters. The Aclara i210+c™
meter is an electronic, single-phase or network, demand and time-
of-use (TOU) electricity meter intended primarily for residential
applications.
Technical Overview
The FlexNet communications network offers a simple, reliable, and
secure system that is economical for mass meter deployments, strategic
deployments, and rural applications while providing a multi-application
solution for all AMI end points. The FlexNet network enhances the
i210+c meter by providing AMI capability.
The FlexNet SmartPoint module is a printed circuit board which
provides wireless communication capability to the Aclara i210+c
electric meter. The SmartPoint module interrogates the meter registers
on a programmable interval from five minutes to daily readings. The
SmartPoint module then transmits the meter consumption and status
information at regular intervals.
The module mounts into the existing i210+c meter and acts as a “third
party AMR board.” It is designed to mount mechanically into the meter
with no additional mechanical modification required.
The module communicates via the FlexNet fixed wireless telemetry
network to provide electric meter readings and diagnostic data from the
meter to the utility provider via radio.
The module contains both a receiver and transmitter to allow for two-
way communications over the FlexNet network.
Specifications
The i210+c meter with the FlexNet module will
have a visible label containing the following
information:
 Contains Model: FLXI2102
 Contains FCC ID: SDBFLXI2102
 Contains IC: 2220A-FLXI2102
Board Location
EQG-10011-01
xylem.com
©2022 Sensus. All products purchased and services performed are subject to Sensus’ terms of sale, available at either sensus.com/TC or 1-800-638-3748. Sensus reserves the right to modify these
terms and conditions in its own discretion without notice to the customer. The Sensus logo is a registered trademark of Sensus.
This document is for informational purposes only, and SENSUS MAKES NO EXPRESS WARRANTIES IN THIS DOCUMENT. FURTHERMORE, THERE ARE NO IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION, WARRANTIES AS TO FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY. ANY USE OF THE PRODUCTS THAT IS NOT SPECIFICALLY PERMITTED HEREIN IS
PROHIBITED.
SENSUS | 637 Davis Drive | Morrisville, NC 27560 | 800.638.3748 | sensus.com
Warnings & Hazards
WARNING
Sensus devices are for professional installation only. They are to be
serviced by professional personnel only. This product is NOT for
consumer installation or servicing.
WARNING
The antenna used for this transmitter must not be co-located in
conjunction with any other antenna or transmitter.
ATTENTION
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different form that
to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
WARNING
If you are not sure of the rated power of your radio, contact your Sensus
representative or dealer and supply the product model number found
on the product label. If you cannot determine the rated power out, then
assure 3-feet separation from the body to the device.
WARNING
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
RADIATION HAZARD
In order to satisfy the FCC RF exposure limit for transmitting devices, a
separation distance of 20cm (7.87 inches) or more should be maintained
while operating the Sensus FLXI2102. To ensure compliance, operation
at closer than this distance is not recommended. This minimum safe
distance is required between personnel and the antenna of this device.
RADIATION HAZARD
In order to satisfy the ISED RF exposure limit for transmitting devices, a
separation distance of 27cm (10.63 inches) or more should be maintained
while operating the Sensus FLXI2102. To ensure compliance, operation
at closer than this distance is not recommended. This minimum safe
distance is required between personnel and the antenna of this device.
Afin de satisfaire à la limite d’exposition RF pour les appareils de
transmission, une distance de séparation de 27cm (10.63 pouces) ou plus
doit être maintenu pendant le fonctionnement du Sensus FLXI2102. Pour
assurer la conformité, un fonctionnement à distance inférieure à celle est
pas recommandée. Cette distance minimale de sécurité est nécessaire
entre le personnel et l’antenne de cet appareil.
ATTENTION
Any modifications made to this device that are not approved by Sensus
may void the authority granted to the user by the FCC to operate
equipment.
ATTENTION
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
ATTENTION
This radio transmitter the Sensus FLXI2102 has been approved by
Industry Canada to operate with the antenna types listed below with the
maximum permissible gain and required antenna impedance for each
antenna type indicated. Antenna types not included in this list, having a
gain greater than the maximum gain indicated for that type, are strictly
prohibited for use with this device.
Le présent émetteur radio (Sensus FLXI2102) a été approuvé par Industrie
Canada pour fonctionner avec les types d’antenne énumérés ci-dessous
et ayant un gain admissible maximal et l’impédance requise pour chaque
type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont
le gain est supérieur au gain maximal indiqué, sont strictement interdits
pour l’exploitation de l’émetteur.
• 1/4 wave printed monopole with peak gain of 2.77dBi
ATTENTION
Under Industry Canada regulations, this radio transmitter may only
operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should be
so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not
more than that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent
émetteur radio peut fonctionner avec une antenne d’un type et d’un
gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie
Canada. Dans le but de réduire les risques de brouillage radioélectrique
à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son
gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne
dépasse pas l’intensité nécessaire à l’établissement d’une communication
satisfaisante.
ATTENTION
ICES-003 Class B Notice—Avis NMB-003, Class B
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numerique de la classe B est conforme à la norme NMB-003
du Canada.
  • Page 1 1
  • Page 2 2

Xylem FLXI2102 Mode d'emploi

FLXI2102
Xylem
Marque
Xylem
Modèle
FLXI2102
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents