Legrand WZ3S3C100 Motion Sensor Manuel utilisateur

Marque: Legrand

Modèle: WZ3S3C100 Motion Sensor

Taper: Manuel utilisateur

Catalog Number: WZ3S3C100

Country of Origin: Made in China

No: 341277 10/20

Motion Sensor – Zigbee 3.0

Installation Instructions

SAFETY INFORMATION

WARNING: Keep batteries away from children at all times. This product

contains a coin/button style cell battery and, if swallowed, can cause severe

internal burns within 2 hours of ingesting and can lead to death. Keep away

from infants and small children at all times. If battery is swallowed or comes

incontact with the inside of the body, immediately seek emergency medical

attention. If the battery is replaced by an incorrect size, there is a risk of the

battery erupting and causing injury. Dispose of used battery promptly, when

it has been removed.

CHOKING HAZARD: Keep batteries and any small parts away from infants

and small children at all times. This item is not a toy and should not be given

to children.

IMPORTANT: Do not expose to wet conditions. Periodically check the

condition and security of the batteries.

WZ3S3C100

Motion Sensor

341277 – 10/20

800-223-4185

1.877.BY.LEGRAND

www.legrand.us

www.legrand.ca

INSTALLATION

IMPORTANT:

• Avoid obstructing the sensor

• Avoid installation near air-conditioners, electric

fans, refrigerators, ovens or other places where

• Install indoors

• Use 3/16” drill bit for drywall anchors

Mount Sensor:

Motion sensor can be mounted on wall or corners.

be 16 feet with a 110° view angle. If mounted at a lower

height, the detection range may be decreased.

For both Wall Mount and Corner Wall Mount

(and drywall anchors, if needed) or double-sided tape.

Set Up Your System

This sensor is designed to work with a Zigbee hub. Loosen

battery cover screw and pull tab to connect the battery,

second to indicate commissioning mode. If not, press and

hold the reset button for 3 seconds. Follow the instructions

from your hub to commission the device. If the sensor is

enrolled successfully, the LED will stop blinking and stay on

Attach sensor to bracket.

For more information on this product please see this link, or

scan the QR code.

https://www.legrand.us/radiant/products/smart-lighting/

wz3s3c100.aspx

TROUBLESHOOTING

they may be too far from the Hub. You can try to put them

closer to the the Hub.

If the sensor is not working, make sure the battery has

power and it is installed with the “+” side facing up to

battery cover. Replace the battery if needed.

False Alarm

The following may cause unintended alarms:

• Heat sources like electric heaters, heat vents and

• Cold sources like drafty windows, air conditioners and

AC vents.

• Curtains near windows that may move while the system is

armed.

• Direct sun exposure: the front of motion sensor should

not be placed in direct sunlight.

Tamper Alarm

When the sensor is removed from the bracket it can trigger

Be sure that the sensor is securely attached to the bracket

MAINTENANCE

Reset to Factory Settings

Press and hold the reset switch for 3 seconds. The LED

indicator will start blinking quickly, the sensor will reset to

second to indicate commissioning mode.

Battery Replacement

The app will notify you when a device’s battery gets low. To

unintended tamper alarm.

Step 1: Disarm the system.

Step 2: Remove the sensor from the bracket.

Step 3: Loosen the screw on the battery cover. Open the

battery cover.

Step 4: Remove the old battery and replace with new

CR2032 battery.

Step 5: Close the battery cover. Tighten the screw for the

battery cover.

Step 6: Hang the sensor on the bracket.

COMPLIANCE INFORMATION

FCC ID: 2AU5D8ASSZAH0

IC: 25764-8ASSZAH0

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

FCC Caution:

the part responsible for compliance could void the user’s authority to

operate the equipment.

FCC Statement: This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth

for an uncontrolled environment. This equipment should be installed

and operated with a minimum distance of 20cm between the radiator

and any part of your body.:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth

for an uncontrolled environment. This equipment should be installed

and operated with minimum distance 20cm between the radiator &

your body.

ISED Statement

This Class [B] digital apparatus complies with Canadian CAN ICES-

3(B).

Cet appareil numérique de la classe [B] est conforme à la norme

NMB-3(B)du Canada.

This device contains licence-exempt transmitter(s)/receiver(s)

that comply with Innovation, Science and Economic Development

Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference

that may cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent

appareil est conforme aux CNR d’Innovation, Sciences et

Développement économique Canada applicables aux appareils

radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes :

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage radioélectrique subi, même

si le brouillage est susceptible d’en compromettre le fonctionnement

This Equipment complies with ISED RSS-102 radiation exposure

limits set forth for an uncontrolled environment. This equipment

should be installed and operated with a minimum distance of 20cm

between the radiator and any part of your body.

Pour se conformer aux exigences de conformité CNR 102 RF

exposition, une distance de séparation d’au moins 20 cm doit être

maintenue entre l’antenne de cet appareil ettoutes les personnes.

Peal back

adhesive

liner

Proper screw locations for wall-mount installation

Corner Flat Surface

8-9 ft.

0 4 6 8 10 12 14 16 ft.

110ْ

0 8 ft.8 ft.16 ft.

Tall Furniture/Cabinet

Wall Mount Corner Wall Mount

LIMITED ONE YEAR WARRANTY

Legrand will remedy any defect in workmanship or material in Legrand products

which may develop under proper and normal use within one year from date of

purchase by a consumer:

(1) by repair or replacement, or, at Legrand’s option, (2) by return of an amount

equal to consumer’s purchase price. Such remedy is IN LIEU OF ANY AND

ALL EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE. Such remedy by Legrand

does not include or cover cost of labor for removal or reinstallation of the

product. ALL OTHER FURTHER ELEMENTS OF DAMAGE (INCIDENTAL

OR CONSEQUENTIAL DAMAGES) FOR BREACH OF ANY AND ALL

EXPRESSED OR IMPLIED WARRANTIES INCLUDING WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE

EXCLUDED HEREBY. (Some states do not allow disclaimers or exclusion or

limitation of incidental or consequential damages, so the above disclaimer and

limitation or exclusion may not apply to you.) ANY IMPLIED WARRANTIES

INCLUDING WHERE REQUIRED WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE ONE

YEAR PERIOD SET FORTH ABOVE. (Some states do not allow limitations on

how long an implied warranty lasts, so the above limitation may not apply to you.)

To ensure safety, all repairs to Legrand products must be made by Legrand, or

obligation is as follows: (1) Contact Legrand, Syracuse, New York 13221, for

instructions concerning return or repair; (2) return the product to Legrand,

postage paid, with your name and address and a written description of the

installation or use of the Legrand product, and the observed defects or failure

to operate, or other claimed basis for dissatisfaction. This warranty gives you

to state.

Legrand WZ3S3C100 Motion Sensor Manuel utilisateur

Marque: Legrand

Modèle: WZ3S3C100 Motion Sensor

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Legrand WZ3S3C100 Motion Sensor User manual

Legrand WZ3S3C100 Motion Sensor Manuel utilisateur

Legrand WZ3S3C100 Motion Sensor Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents