Develco Motion Sensor Manuel utilisateur

Catégorie
Cheminées
Taper
Manuel utilisateur
eng a.
c. g.
k.
l.
b.
d.
e.
f.
i.
j.
h.
MOUNTING FLAT ON CEILING OR WALL
1. Open the casing, and use the sensor part
with oval holes to mark the screw holes on
the ceiling or the wall.
2. Mount the sensor on the wall or the ceiling
by installing one screw from the bag
marked “A” through each oval hole. Using
screws for mounting is the most secure
mounting option, as it prevents sudden,
unwanted removal.
Place the sensor indoors at a temperature
between 16-50°C.
Its angle of detection from above, the sides,
and below must be 45°.
Place the Motion Sensor Mini in a location
with a clear view of the monitored area and
the windows.
The distance from the sensor to a replace
or a stove must be at least four meters.
The Motion Sensor Mini must be reachable
for battery testing and maintenance.
Place the sensor free of curtains and other
obstacles.
Avoid placing the Motion Sensor Mini close
to a heating/cooling source.
Avoid placing the Motion Sensor Mini in
direct sunlight or bright light.
Product description
The compact Motion Sensor Mini allows you to
detect if somebody is in the room or not. With
the Motion Sensor Mini, you can set the light
to turn on and o as people come and go. The
motion sensor is PIR based and is able to sense
movement up to 9 meters from the sensor.
Motion Sensor Mini
Version 3.4
INSTALLATION MANUAL Placement
CORNER OR CEILING MOUNTING WITH
CORNER BRACKET
1. If you have a sensor with a corner bracket
included, you can mount the sensor with
this bracket in a corner or on the ceiling.
2. Use the corner bracket to mark the screw
holes on the two walls in the corner of the
room or on the ceiling.
3. Use the two screws in the bag marked “A
to install the bracket in the marked place.
Using screws for mounting is the most
secure mounting option, as it prevents
unwanted removal, e.g. by intruders.
Alternatively, you can use the two small,
round pieces of double adhesive tape to
mount the bracket in the corner (do not
mount it on the ceiling with tape). Make
sure to press rmly on the bracket with the
tape to make it stick, and then attach the
sensor to the bracket.
Mounting
There are several mounting options for the
Motion Sensor Mini. You can mount it at on
a ceiling or wall, using the screws, adhesive
tape, or magnet. If you have a sensor with a
corner bracket included, you can mount the
bracket in corners or on the ceiling, using
screws or adhesive tape. Afterwards, you can
attach the sensor to the bracket by using the
magnet inside the device or the screws. If you
have a stand included, you can also place the
sensor on the stand.
When mounting with a corner bracket, you
have two options for mounting the sensor on
the bracket: either with the magnet or screws.
MOUNTING THE SENSOR ON THE CORNER
BRACKET WITH THE SCREWS
If you are using the sensor for security
purposes, we recommend using screws to
mount the sensor on the bracket for a more
secure fastening.
1. Open the casing of the sensor.
MOUNTING WITH MAGNET
If your sensor includes a corner bracket, you
can mount the sensor at on the wall or ceiling,
using the magnet from the bracket.
1. Unscrew the small magnet from the
bracket.
2. Screw the magnet on a ceiling or a wall.
MOUNTING THE SENSOR ON THE CORNER
BRACKET WITH THE MAGNET
1. Open the casing of the sensor.
2. Insert batteries.
3. Close the casing of the sensor.
4. Attach the sensor to the corner bracket,
which includes a magnet.
3. Attach the sensor to the magnet.
Precautions
When mounting with tape, make sure the
surfaces are clean and dry.
When mounting with tape, the room
temperature should ideally be between 21°
C and 38° C and minimum 16° C.
Avoid mounting with tape on rough, porous
or bered materials such as wood or
cement, as they reduce the tape bond.
2. Place the part with oval holes against the
already mounted bracket.
Alternatively, you can use the large, round
piece of double adhesive tape to mount
the sensor. Make sure to press rmly on
the sensor with the tape to make it stick.
3. Insert batteries and make sure that the
battery polarity is correct (+/-).
4. Close the casing of the sensor.
Disclaimers
CAUTION:
Choking hazard! Keep away from children.
Contains small parts.
Please follow the guidelines thoroughly.
The Motion Sensor Mini is a preventive,
informing device, not a guarantee or
insurance that sucient warning or
protection will be provided, or that no
property damage, theft, injury, or any
similar situation will take place. Develco
Products cannot be held responsible
in case any of the above-mentioned
situations occur.
T00000059 Motion Sensor Mini installation manual, v3.4.indd 1T00000059 Motion Sensor Mini installation manual, v3.4.indd 1 10/7/2021 12:04:50 PM10/7/2021 12:04:50 PM
o.
p.
n.
q.
m.
Develco Products assumes no responsibility
for any errors, which may appear in this manual.
Furthermore, Develco Products reserves
the right to alter the hardware, software,
and/or specications detailed herein at any
time without notice, and Develco Products
does not make any commitment to update
the information contained herein. All the
trademarks listed herein are owned by their
respective owners.
All rights reserved.
Other certications
Zigbee Home Automation 1.2 certied.
Disposal
Dispose the product and battery properly at
the end of their lives. This is electronic waste,
which should be recycled.
IN ACCORDANCE WITH THE DIRECTIVES
Radio Equipment Directive (RED)
2014/53/EU
RoHS Directive 2015/863/EU amending
2011/65/EU
REACH 1907/2006/EU + 2016/1688
IC statement
Distributed by Develco Products A/S
Tangen 6
8200 Aarhus N
Denmark
www.develcoproducts.com
ISED statement
Innovation, Science and Economic
Development Canada ICES-003 Compliance
Label: CAN ICES-3 (B)/NMB-3(B).
ISED statement
The device will blink twice every minute when
the battery is low.
Battery replacement
Resetting
Resetting is needed if you want to connect
your Motion Sensor Mini to another gateway,
or if you need to perform a factory reset to
eliminate abnormal behaviour.
4. While you are holding the button down, the
LED rst ashes once, then two times in a
row, and nally numerous times in a row.
5. Release the button while the LED is ashing
numerous times in a row.
6. After you release the button, the LED shows
one long ash, and the reset is completed.
Connecting
1. When batteries are inserted, the Motion
Sensor Mini will automatically start
searching (up to 15 minutes) for a Zigbee
network to join.
2. Make sure that the Zigbee network is open
for joining devices and will accept the
Motion Sensor Mini.
3. While the sensor is searching for a Zigbee
network to join, the LED ashes red.
Modes
SEARCHING GATEWAY MODE
Red LED light is ashing every second (up to 15
minutes).
LOW BATTERY MODE
The device will ash red twice every minute
when the battery is low.
STAND
1. If you have a sensor with
a plastic stand included,
you can insert the stand
in the opening on the
back of the sensor as
shown on the drawing.
2. Place the standing sensor
on the shelf or on a desk.
CE certication
The CE mark axed to this product conrms
its compliance with the European Directives
which apply to the product and, in particular,
its compliance with the harmonized standards
and specications.
Fault nding
In case of a bad or weak signal, change
the location of the Motion Sensor Mini.
Otherwise, you can relocate your gateway
or strengthen the signal with a smart plug.
If the search for a gateway has timed out, a
short press on the button will restart it.
FCC statement
Changes or modications to the equipment not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful
STEPS FOR RESETTING
1. Detach the sensor from the bracket and/or
open the casing.
2. Check that the batteries are inserted
correctly.
3. Press and hold the round menu button
inside the device.
4. When the sensor is connected to a network,
it will stop ashing.
3. Take two screws from the bag marked “B”.
Mount one screw through each oval hole
and into two holes on the corner bracket.
4. Insert batteries and make sure that the
battery polarity is correct (+/-).
5. Close the casing of the sensor.
interference to radio or television reception,
which can be determined by turning the
equipment o and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on
a circuit dierent from that to which the
receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
This device complies with FCC RF radiation
exposure limits set forth for an uncontrolled
environment. The antenna used for this
transmitter must be installed to provide a
separation distance of at least 20 cm from
all persons and must not be co-located or
operating in conjunction with any other antenna
or transmitter.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any interference
received, including interference that may
cause undesired operation.
Français
L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences
et Développement économique Canada
applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux
conditions suivantes :
1. L’appareil ne doit pas produire de
brouillage;
English
This device contains licence-exempt
transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the following
two conditions:
1. This device may not cause interference.
2. This device must accept any interference,
including interference that may cause
undesired operation of the device.
This equipment complies with IC RSS-102
radiation exposure limits set forth for an
uncontrolled environment. This equipment
should be installed and operated with
minimum distance 20 cm between the radiator
and your body.
2. L’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le
fonctionnement.
Cet équipement est conforme aux limites
d’exposition aux radiations IC CNR-102 établies
pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec
une distance minimale de 20 cm entre le
radiateur et votre corps.
CAUTION:
Do not attempt to recharge or open the
batteries.
Risk of explosion if batteries are replaced by
an incorrect type.
Dispose of a battery into re or a hot oven,
or mechanically crushing or cutting of a
battery can result in an explosion
Leaving a battery in an extremely high
temperature surrounding environment can
result in an explosion or the leakage of
ammable liquid or gas.
A battery subjected to extremely low air
pressure may result in an explosion or the
leakage of ammable liquid or gas
Maximum operation temperature is 50°C /
122°F
If you experience leakage from the
batteries, immediately wash your hands
and/or any aected area of your body
thoroughly!
CAUTION: When removing cover for battery
change - Electrostatic Discharge (ESD) can
harm electronic components
1. To replace the battery, detach the Motion
Sensor Mini from the bracket and/or open
the casing.
2. Replace the battery respecting the
polarities.
3. Close the casing of the sensor. inside.
ALARM TESTING MODE
The motion sensor will automatically ash
green every time movement is detected by the
Intruder Alarm System (IAS), no matter if the
alarm system is activated or deactivated. The
green ashes can help you determine if the
placement of the sensor is suitable for alarm
purposes.
T00000059 Motion Sensor Mini installation manual, v3.4.indd 2T00000059 Motion Sensor Mini installation manual, v3.4.indd 2 10/7/2021 12:04:52 PM10/7/2021 12:04:52 PM
  • Page 1 1
  • Page 2 2

Develco Motion Sensor Manuel utilisateur

Catégorie
Cheminées
Taper
Manuel utilisateur

dans d''autres langues