Develco Products H6500113 Manuel utilisateur

Marque: Develco Products

Modèle: H6500113

Taper: Manuel utilisateur

eng

Getting started

1. Open the casing of the device by removing

the screw at the bottom of the device.

2. Use the included screws to mount the back

plate of the device on the wall

4. Insert batteries into the device respecting

the polarities.

5. When the batteries are inserted, the

Intelligent Keypad will start searching (up

to 15 minutes) for a Zigbee network to join.

While the Intelligent Keypad is searching for

a Zigbee network to join, the yellow LED

ashes.

6. If the scanning has timed out, a short press

on the menu button inside the device will

restart it.

7. After connecting the device to a network,

attach the device to the back plate by

hooking the device to the top of the back

plate and pushing the device against the

back plate.

Battery replacement

CAUTION:

• Do not attempt to recharge or open the

batteries.

• Risk of explosion if batteries are replaced by

an incorrect type.

• Dispose of a battery into re or a hot oven, or

mechanically crushing or cutting of a battery

can result in an explosion

• Leaving a battery in an extremely high

temperature surrounding environment can

result in an explosion or the leakage of

ammable liquid or gas.

• A battery subjected to extremely low air

pressure may result in an explosion or the

leakage of ammable liquid or gas

• Maximum operation temperature is 50°C /

122°F

• If you experience leakage from the batteries,

immediately wash your hands and/or any

aected area of your body thoroughly!

CAUTION: When removing cover for battery

change - Electrostatic Discharge (ESD) can

harm electronic components inside.

1. To replace the batteries, remove the screw

at the bottom of the device and open the

casing.

2. Replace all four batteries inside the device,

respecting the polarities.

3. Reattach the device to the backplate and

reinsert the screw at the bottom of the

device

8. Finally, reinsert the screw at the bottom of

the device

Resetting

Resetting is needed if you want to connect

your Intelligent Keypad to another gateway or

if you need to perform a factory reset to avoid

abnormal behavior.

STEPS FOR RESETTING

1. Open the casing of the device by removing

the screw at the bottom of the device.

2. Press and hold the menu button inside the

device with a thin pin – e.g. a paper clip.

Placement

• You can place the Intelligent Keypad both

indoors and outdoors in 0-50 degrees °C.

• Place the device, so it is easily accessible to

users.

• Avoid placing the device in direct sunlight.

• Avoid placing the device in places exposed

to direct rain.

• Avoid placing moving items 40 cm or less

from the Intelligent Keypad, as they will

activate the presence sensor.

• When mounting the device outdoors, use

screws rather than tape.

Precautions

• Do not remove the product label as it

contains important information.

• Be aware that electronics are sensitive

to static electricity, so aim to discharge

before touching, and avoid touching any

components inside the device.

• Do not paint the device.

• Do not use tape for mounting the device

outdoors.

• Do not use tape for mounting if you will use

the device for security purposes, as the

tamper switch will not function.

• When mounting with tape, make sure the

surfaces are clean and dry.

• When mounting with tape, the room

temperature should ideally be between 21°

C and 38° C and minimum 16° C.

• Avoid mounting with tape on rough, porous

or bered materials such as wood or

cement, as they reduce the tape bond.

Product description

The Intelligent Keypad includes a tag reader

and allows you to enable and disable an alarm

system. The Intelligent Keypad detects when

a person is within operating distance, which

will make it light up in the dark. The Intelligent

Keypad includes a tamper switch, making it

ideal for security purposes.

Version 3.0

INSTALLATION MANUAL

Intelligent Keypad

3. While you are holding the button down, the

LED rst ashes once, then two times in a

row, and nally numerous times in a row.

4. Release the button while the LED is ashing

numerous times in a row.

5. After you release the button, the LED shows

one long ash, and the reset is completed.

3. Alternatively, you can use the double

adhesive tape to mount the backplate. Make

sure to press rmly on the backplate with

the tape to make it stick.

Disclaimers

CAUTION:

• Choking hazard! Keep away from children.

Contains small parts.

• Please follow the guidelines thoroughly. The

Intelligent Keypad is a preventive, informing

device, not a guarantee or insurance that

sucient warning or protection will be

provided, or that no property damage,

theft, injury, or any similar situation will

take place. Develco Products cannot be

held responsible in case any of the above-

mentioned situations occur.

Other certications

Zigbee 3.0 certied

Disposal

Dispose the product and batteries properly at

the end of their lives. This is electronic waste

which should be recycled.

Develco Products assumes no responsibility for

any errors, which may appear in this manual.

Furthermore, Develco Products reserves the

right to alter the hardware, software, and/

or specications detailed herein at any time

without notice, and Develco Products does

not make any commitment to update the

information contained herein. All the trademarks

listed herein are owned by their respective

owners.

Distributed by Develco Products A/S

Tangen 6

8200 Aarhus

Denmark

IN ACCORDANCE WITH THE DIRECTIVES

• Radio Equipment Directive (RED) 2014/53/

• RoHS Directive 2015/863/EU amending

2011/65/EU

• REACH 1907/2006/EU + 2016/1688

CE certication

The CE mark axed to this product conrms

its compliance with the European Directives

which apply to the product and, in particular, its

compliance with the harmonized standards and

specications.

FCC statement

Changes or modications to the equipment not

expressly approved by the party responsible for

compliance could void the user’s authority to

operate the equipment.

NOTE: This equipment has been tested and

found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is no

guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful

interference to radio or television reception,

which can be determined by turning the

equipment o and on, the user is encouraged

to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on

a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/

TV technician for help.

This device complies with FCC RF radiation

exposure limits set forth for an uncontrolled

environment. The antenna used for this

FCC statement

English

This device contains licence-exempt

transmitter(s)/receiver(s) that comply

with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two

conditions:

1. This device may not cause interference.

2. This device must accept any interference,

including interference that may cause

undesired operation of the device.

This equipment complies with IC RSS-102

radiation exposure limits set forth for an

uncontrolled environment. This equipment

should be installed and operated with minimum

distance 20 cm between the radiator and your

body.

Français

L’émetteur/récepteur exempt de licence

contenu dans le présent appareil est

conforme aux CNR d’Innovation, Sciences

et Développement économique Canada

applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux

conditions suivantes :

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le

fonctionnement.

Cet équipement est conforme aux limites

IC statement

ISED statement

Innovation, Science and Economic

Development Canada ICES-003 Compliance

Label: CAN ICES-3 (B)/NMB-3(B).

ISED statement

Fault nding and cleaning

• In case of a bad or wireless weak signal,

change the location of the device. Otherwise

you can relocate your gateway or strengthen

the signal with a range extender.

• If the search for a gateway has timed out, a

short press on the button will restart it.

transmitter must be installed to provide a

separation distance of at least 20 cm from

all persons and must not be co-located or

operating in conjunction with any other antenna

or transmitter.

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interfer-

ence, and

2. this device must accept any interference

received, including interference that may

cause undesired operation.

d’exposition aux radiations IC CNR-102 établies

pour un environnement non contrôlé. Cet

équipement doit être installé et utilisé avec une

distance minimale de 20 cm entre le radiateur

et votre corps.

Develco Products H6500113 Manuel utilisateur

Marque: Develco Products

Modèle: H6500113

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Develco Products H6500113 User manual

Develco Products H6500113 Manuel utilisateur

Develco Products H6500113 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents