Develco WISZB-137 Manuel utilisateur

Marque: Develco

Modèle: WISZB-137

Taper: Manuel utilisateur

Bed Frame

Frame Window/

Door

Pipe

eng

Mounting

1. Clean the surface before mounting.

2. The Vibration Sensor should be mounted

on the surface using the double stick tape,

already applied on the back of the sensor.

Press rmly to secure sensor.

MOUNTING EXAMPLE 1: WINDOW

1. Clean the surface before mounting.

2. The Vibration Sensor should be mounted

on the window frame using the double

stick tape, already applied on the back of

the sensor. Press rmly to secure sensor.

Placement

• Place the sensor indoors at a temperature

between 0-50°C.

• In case of a weak or a bad signal, change

the location of the Vibration Sensor or

strengthen the signal with a smart plug.

• The Vibration Sensor can be placed on

dierent surfaces indoors such as windows,

cabinets, chairs, tables, beds, pipes, a

compressor or anywhere else where

vibrations can give valuable insights.

• When removing cover for battery change -

electrostatic discharge can harm electronic

components inside.

• Always mount indoors as sensor is not

waterproof.

Getting started

1. Open the casing of the device by pushing

the fastening on top of the device to remove

the front panel from the back cover.

Product description

The Vibration Sensor detects and reports

vibration. Attached to windows, the Vibration

Sensor can detect breaking glass and warn

about break-ins. It can be mounted underneath

beds to monitor patients* sleep or on piping to

identify blockages and other abnormalities.

Vibration Sensor

2. Insert the enclosed batteries into the device,

respecting the polarities.

3. Close the casing.

4. The Vibration Sensor will now start

searching (up to 15 minutes) for a Zigbee

network to join.

5. Make sure that the Zigbee network is open

for joining devices and will accept the

Vibration Sensor.

6. While the Vibration Sensor is searching for

a Zigbee network to join, the red LED is

ashing.

Precautions 7. When the red LED stops ashing, the

Vibration Sensor has successfully joined the

Zigbee network.

INSTALLATION MANUAL

Version 1.2

Resetting

Resetting is needed if you want to connect your

Vibration Sensor to another gateway or if you

need to perform a factory reset to eliminate

abnormal behavior.

The reset button is marked with the small ring

on the front of the sensor.

STEPS FOR RESETTING

1. Press and hold down the reset button until

the LED rst ashes once, then two times in

a row, and nally numerous times in a row.

2. Release the button while the LED is ashing

numerous times in a row.

Modes

SEARCHING GATEWAY MODE

Red ashes every second for a longer period,

means that the device is searching for a

gateway.

LOST CONNECTION MODE

When the red LED ashes 3 times, it means that

the device has failed to connect to a gateway.

LOW-BATTERY MODE

Two consecutive red LED ashes every 60

seconds, means that the battery should be

replaced.

Fault nding

• In case of a bad or weak signal, change

the location of the Vibration Sensor.

Otherwise you can relocate your gateway

or strengthen the signal with a smart plug.

• If the search for a gateway has timed out, a

short press on the button will restart it.

Battery replacement

CAUTION:

• Do not attempt to recharge or open the

batteries.

• Risk of explosion if batteries are replaced by

an incorrect type.

• Dispose of a battery into re or a hot oven, or

mechanically crushing or cutting of a battery

can result in an explosion

• Leaving a battery in an extremely high

temperature surrounding environment can

result in an explosion or the leakage of

ammable liquid or gas.

• A battery subjected to extremely low air

pressure may result in an explosion or the

leakage of ammable liquid or gas

• Maximum operation temperature is 50°C /

122°F

• If you experience leakage from the batteries,

immediately wash your hands and/or any

aected area of your body thoroughly!

CAUTION: When removing cover for battery

change - Electrostatic Discharge (ESD) can

harm electronic components inside.

1. Open the casing of the device by pushing

the fastening on top of the device to remove

the front panel from the back cover.

2. Replace the batteries respecting the

polarities. The Vibration Sensor uses 2xAAA

batteries.

3. Close the casing.

4. Test the Vibration Sensor.

Other information

Note local regulations about information to

your insurance company regarding installed

Vibration Sensors.

Disclaimers

CAUTION:

• Choking hazard! Keep away from children.

Contains small parts.

• Please follow the guidelines thoroughly. The

Vibration Sensor is a preventive, informing

device, not a guarantee or insurance that

sucient warning or protection will be

provided, or that no property damage,

theft, injury, or any similar situation will

take place. Develco Products cannot be

held responsible in case any of the above-

mentioned situations occur.

3. After you release the button, the LED shows

one long ash, and the reset is completed.

MOUNTING EXAMPLE 3: PIPINGS

1. Clean the surface before mounting.

2. The Vibration Sensor should be mounted

on the pipe using the double stick tape,

already applied on the back of the sensor.

Press rmly to secure sensor.

MOUNTING EXAMPLE 2: BED

1. Clean the surface before mounting.

2. The Vibration Sensor should be mounted

on the frame underneath the bed using the

double stick tape, already applied on the

back of the sensor. Press rmly to secure

sensor.

H6500187 Vibration Sensor installation manual v1.2.indd 1H6500187 Vibration Sensor installation manual v1.2.indd 1 10/7/2021 12:11:50 PM10/7/2021 12:11:50 PM

Other certications

Zigbee 3.0 certied

Develco Products assumes no responsibility for

any errors, which may appear in this manual.

Furthermore, Develco Products reserves the

right to alter the hardware, software, and/

or specications detailed herein at any time

without notice, and Develco Products does

not make any commitment to update the

information contained herein. All the trademarks

listed herein are owned by their respective

owners.

Distributed by Develco Products A/S

Tangen 6

8200 Aarhus

Denmark

IN ACCORDANCE WITH THE DIRECTIVES

• Radio Equipment Directive (RED) 2014/53/

• RoHS Directive 2015/863/EU amending

2011/65/EU

• REACH 1907/2006/EU + 2016/1688

CE certication

The CE mark axed to this product conrms

its compliance with the European Directives

which apply to the product and, in particular, its

compliance with the harmonized standards and

specications.

FCC statement

Changes or modications to the equipment not

expressly approved by the party responsible for

compliance could void the user’s authority to

operate the equipment.

NOTE: This equipment has been tested and

found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is no

guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful

interference to radio or television reception,

which can be determined by turning the

equipment o and on, the user is encouraged

to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on

a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/

TV technician for help.

This device complies with FCC RF radiation

exposure limits set forth for an uncontrolled

environment. The antenna used for this

transmitter must be installed to provide a

separation distance of at least 20 cm from

all persons and must not be co-located or

operating in conjunction with any other antenna

or transmitter.

FCC statement

Français

L’émetteur/récepteur exempt de licence

contenu dans le présent appareil est

conforme aux CNR d’Innovation, Sciences

et Développement économique Canada

applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux

conditions suivantes :

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le

fonctionnement.

Cet équipement est conforme aux limites

d’exposition aux radiations IC CNR-102 établies

pour un environnement non contrôlé. Cet

équipement doit être installé et utilisé avec une

distance minimale de 20 cm entre le radiateur

et votre corps.

English

This device contains licence-exempt

transmitter(s)/receiver(s) that comply

with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two

conditions:

1. This device may not cause interference.

2. This device must accept any interference,

including interference that may cause

undesired operation of the device.

This equipment complies with IC RSS-102

radiation exposure limits set forth for an

uncontrolled environment. This equipment

should be installed and operated with minimum

distance 20 cm between the radiator and your

body.

IC statement

ISED statement

Innovation, Science and Economic

Development Canada ICES-003 Compliance

Label: CAN ICES-3 (B)/NMB-3(B).

ISED statement

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference, and

2. this device must accept any interference

received, including interference that may

cause undesired operation.

Disposal

Dispose the product and battery properly at the

end of life. This is electronic waste which should

be recycled.

H6500187 Vibration Sensor installation manual v1.2.indd 2H6500187 Vibration Sensor installation manual v1.2.indd 2 10/7/2021 12:11:50 PM10/7/2021 12:11:50 PM