VTech DM1411 Guide de démarrage rapide

Marque: VTech

Modèle: DM1411

Catégorie: Moniteurs vidéo bébé

Taper: Guide de démarrage rapide

Note

• This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and

should not be used as such.

Test your baby monitor

You may test the baby monitor before initial use, and at regular times thereafter.

Caution

• For hearing protection, make sure the parent

unit is more than 3 feet (1 meter) away from the

baby unit. If you hear any high-pitched noise,

move the parent unit further until the noise

stops. You can also press on the parent unit to

lower or mute the noise.

1. Make sure your soother and parent unit

are on.

2. Speak towards the microphone of the soother

You will hear the sound at the parent unit, and

see the visual sound indicators light up.

Note

• When the POWER/LINK LED light ﬂashes, move the parent unit closer to the soother (observe

the minimum distance of 3 feet / 1 meter). You can also check if the soother is connected to a

live power socket and switched on.

Tip

• Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the

soother.

Positioning the baby monitor

Caution

• Keep the soother out of the reach of your baby. Never place or mount the soother inside the

baby’s crib or playpen.

1. Place the soothers more than 3 feet (1 meter) away from

your baby.

2. Place the parent unit more than 3 feet (1 meter) away from the

soother to avoid screeching noise.

Caution

• The default volume of your parent unit is level 3, and the maximum

volume is level 5. If you experience high-pitched screeching noise from

your baby monitor while positioning:

- Make sure your soothers and parent unit are more than

3 feet (1 meter) apart, OR

- Turn down the volume of your parent unit.

Operating range

The operating range of the baby monitor is up to

1000 feet (300 meters) outdoors or 160 feet (50

meters) indoors. The actual operating range may vary

depending on the environmental conditions and

other interferences such as walls, doors and other

obstructions.

DM1411

Digital Audio Monitor

Go to www.vtechphones.com

to register your product for

enhanced warranty support and

the latest VTech product news.

Congratulations

on purchasing your new VTech product.

Before using this product, please read Important safety instructions.

This manual has all the feature operations and troubleshooting necessary to install and operate

your new VTech product. Please review this manual thoroughly to ensure proper installation and

operation of this innovative and feature-rich VTech product.

For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com.

1 Connect the baby monitor

What’s in the box

Frequency control Crystal controlled PLL synthesizer

Transmit frequency Soother: 1921.536 - 1928.448 MHz

Parent unit: 1921.536 - 1928.448 MHz

Channels 5

Nominal effective range Maximum power allowed by FCC and IC. Actual operating range

may vary according to environmental conditions at the time of use.

Power requirements Soother adapter: Output: 5V DC @ 600mA

Parent unit adapter: Output: 6V DC @ 400mA

Parent unit battery: 2.4V NiMH battery

Technical speciﬁcations

Speciﬁcations are subject to change without notice.

Strangulation

Hazard

Keep this cord out of reach of children.

The cord needs to be at least three feet

away from the child at all times. Do not

use with an extension cord. Do not

remove this tag.

Éloignez ce cordon des enfants. Le

cordon doit se trouver à au moins trois

pieds d’un enfant et ce, en tout temps.

N’utilisez pas de rallonge. Ne retirez pas

cette étiquette.

Mantenga este cable fuera de la alcance

de los niños. Este cable debe estar por

lo menos tres pies fuera de la alcance

del niño en todo momento. No lo use

con una extensión inalámbrica. No quite

esta etiqueta.

Risque

d’étranglement

Riesgo de

estrangulación

Strangulation

Hazard

Keep this cord out of reach of children.

The cord needs to be at least three feet

away from the child at all times. Do not

use with an extension cord. Do not

remove this tag.

Éloignez ce cordon des enfants. Le

cordon doit se trouver à au moins trois

pieds d’un enfant et ce, en tout temps.

N’utilisez pas de rallonge. Ne retirez pas

cette étiquette.

Mantenga este cable fuera de la alcance

de los niños. Este cable debe estar por

lo menos tres pies fuera de la alcance

del niño en todo momento. No lo use

con una extensión inalámbrica. No quite

esta etiqueta.

Risque

d’étranglement

Riesgo de

estrangulación

Power on or off the soother

• Switch to ON

Switch to

on the soother only.

to turn on the soother.

• to use the soothing functions

Switch to OFF• to turn off the soother.

Power on or off the parent unit

• Press and hold to turn on the parent unit. The

POWER / LINK LED light turns on.

• Press and hold again to turn off the parent unit. The

POWER / LINK LED light turns off.

Before use

Using the baby monitor

User’s manual DM1411

For more support information

Important safety instructions

Install the parent unit battery

The parent unit runs on rechargeable battery or AC power. To continuously monitor your

baby, make sure you use both battery and AC power at the same time. With the battery

alone, the parent unit can cordlessly run for a short time only.

NOTESNOTE

• Use only the battery supplied with this product.

• If the parent unit will not be used for a long time, disconnect and remove the battery to prevent

possible leakage.

Replace the battery

To replace the battery, press down on the battery compartment cover and pull it out, then

follow the steps above to install the battery.

Connect the baby monitor

NOTESNOTE

• Use only the power adapters supplied with this product.

• Make sure the baby monitor is not connected to a switch controlled electric outlet.

• Connect the power adapters in a vertical or ﬂoor mount position only. The adapters’ prongs are not

designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table,

or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.

• Make sure the parent unit, the soother and the power adapter cords are out of reach of children.

Charge the parent unit battery

When you have connected and turned on the soother and all the parent units, they will

enter pairing mode automatically. It takes around 10 minutes for the pairing process to

complete. When the parent unit and soother are successfully paired, the parent unit

power LED is on steadily. The baby monitor is ready to use.

NOTESNOTE

Notes

• Before using the baby monitor for the ﬁrst time, charge the parent unit battery for 12 hours.

• It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time,

turn the parent unit off while charging.

• The standby time varies depending on the sensitivity level you set, your actual use and the age of the

battery.

• The parent unit beeps twice every 10 minutes and the light ﬂashes in red when the battery is low.

harge the parent unit battery

without interruption

for at least 30 minutes.

• To keep the battery charged, connect it to AC power when not in use.

1 Connect the baby monitor (Cont’d)

t angulation

aard

Kee p ht is cord u

o tof reach of chidl re.n

The cor d nee s

d ot eb a tleas t ht er e feet

away from h

t e child at all times. Do no

use with an extension cord. oD not

remove this tag.

Éloignez ce cordon des enfants. Le

cordon doit se trouver à au moi s

n rt i

pieds ’

dun enfant et ce, en tout temps.

’

Nutilisez pas de rallonge. Ne retirez pas

cette étiquette.

Mantenga este cable fue a

r de la alca cn e

de o

ls niños. E t

se ca lbe debe estar por

lo menos tres pies fuera de la alcance

del niño en todo momento. No lo use

con una extensión inaá

l mbrica. No uq i e

esta etqi ue at .

Risque

’d t

é ranglement

Rie og

sde

eta

n ulaci nó

rtS alu

n a it on

H z

a a dr

Keep ht i scod

r ou to

freach of child e

r n.

The codr need

sto be a tleast ht e

r e fee t

away rf om h

t e child a tall itme .

s oD not

s i

t an ex etnsion codr. Do no t

er move h

t is atg.

Éloignez ce cod

r on de

senfans

t . Le

cod

r on doi

tse toruve

rà au moins rto s

pied

sd’un enfan te tce, en tou t e

t mps.

’

Nutili es z pas de rallonge. Ne e

rtirez pas

cet

te éitquette.

Mane

tnga e t

se cable fuear de la alcance

de lo

sniño .

s Es e

t cable debe es atr po

lo meno

tes pie s u

fear de la alcance

del niño en ot do momen ot. oN lo ues

con una exe

tn i

són inalámb irca. No quite

esta e itque a

iR e

d’étrange

l em tn

R e g

ets ragn ulacói n

> 3ft (1m)

3ft (1m)

> 3ft (1m)

3ft (1m)

> 3ft (1m)

The applied nameplate is located in the battery compartment of

the baby and parent units.

When using your equipment, basic safety precautions should

always be followed to reduce the risk of ﬁre, electric shock and

injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. CAUTION: Do not install the soother at a height above 2

meters.

4. This product is not a substitute for adult supervision of the

infant. Supervising the infant is the parent’s or caregiver’s

responsibility. This product could cease operating, and

therefore you should not assume it will continue working

properly for any given period of time. Further, this is not a

medical device and should not be used as such. This product

is intended to assist you in supervising your baby.

5. Do not use this product near water. For example, do not use

it next to a bath tub, wash bowl, kitchen sink, laundry tub or

swimming pool, or in a wet basement or shower.

6. CAUTION: Use only the batteries provided. There may be

a risk of explosion if a wrong type of battery is used for the

parent unit. The batteries cannot be subjected to high or low

extreme temperature and low air pressure at high altitude

during use, storage or transportation. Disposal of batteries

into ﬁre or a hot oven, or mechanically crushing or cutting or

the batteries can result in an explosion. Leaving the batteries

in an extremely high temperature surrounding environment

can result in an explosion or the leakage of ﬂammable liquid

of gas. Batteries subjected to extremely low air pressure may

result in an explosion or the leakage of ﬂammable liquid or

gas. Dispose of used battery according to the information

in The RBRC seal.

6. Use only the adapters included with this product. Incorrect

adapter polarity or voltage can seriously damage the

product.

7. Use only adaptors and batteries listed below.

Power adapter information:

Output: 6V DC 400mA /5V DC 600mA

VTECH TELECOMMUNICATIONS LTD.

Model: VT05UUS06040 / VT05EUS05060

Rechargeable battery information:

2.4V NiMH battery

YIYANG CORUN BATTERY CO LTD.

Model: NI-MHAAA400×2-FF/ NI-MHAAA750x2-FF

8. The power adapters are intended to be correctly oriented in a

vertical or ﬂoor mount position. The prongs are not designed

to hold the plug in place if it is plugged into a ceiling, under-

the-table or cabinet outlet.

9. For pluggable equipment, the socket-outlet shall be installed

near the equipment and shall be easily accessible.

10. Unplug this product from the wall outlet before cleaning.

Do not use liquid or aerosol cleaners. Use a damp cloth for

cleaning.

11. Unplug the power cords before replacing batteries.

12. Do not cut off the power adapters to replace them with other

plugs, as this causes a hazardous situation.

13. Do not allow anything to rest on the power cords. Do not

install this product where the cords may be walked on or

crimped.

14. This product should be operated only from the type of power

source indicated on the marking label. If you are not sure of

the type of power supply in your home, consult your dealer

or local power company.

15. Do not overload wall outlets or use an extension cord.

16. Do not place this product on an unstable table, shelf, stand

or other unstable surfaces.

17. This product should not be placed in any area where proper

ventilation is not provided. Slots and openings in the back

or bottom of this product are provided for ventilation.

To protect them from overheating, these openings must not

be blocked by placing the product on a soft surface such as a

bed, sofa or rug. This product should never be placed near

or over a radiator or heat register.

18. Never push objects of any kind into this product through

the slots because they may touch dangerous voltage points

or create a short circuit. Never spill liquid of any kind on the

product.

19. To reduce the risk of electric shock, do not disassemble this

product, but take it to an authorized service facility. Opening

or removing parts of the product other than speciﬁed access

doors may expose you to dangerous voltages or other risks.

Incorrect reassembling can cause electric shock when the

product is subsequently used.

20. You should test the sound reception every time you turn on

the units or move one of the components.

21. Periodically examine all components for damage.

22. There is a very low risk of privacy loss when using certain

electronic devices, such as baby monitors, cordless

telephones, etc. To protect your privacy, make sure the

product has never been used before purchase, reset the baby

monitor periodically by powering off and then powering on

the units, and power off the baby monitor if you will not use

it for some time.

23. Children should be supervised to ensure that they do not

play with the product.

24. The product is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the

appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

1. Use and store the product at a temperature between 32oF

and 104oF.

2. Do not expose the product to extreme cold, heat or direct

sunlight. Do not put the product close to a heating source.

3. Batteries should not be exposed to excessive heat such as

bright sunshine or ﬁre.

4. Warning—Strangulation Hazard—Children

have STRANGLED in cords. Keep this cord out

of the reach of children (more than 3 ft (0.9 m)

away). Do not remove this tag.

5. Never place the soother inside the baby’s crib or p laypen.

Never cover the soother or parent unit with anything such

as a towel or a blanket.

6. Other electronic products may cause interference with your

baby monitor. Try installing your baby monitor as far away

from these electronic devices as possible: wireless routers,

radios, cellular telephones, intercoms, room monitors,

televisions, personal computers, kitchen appliances and

cordless telephones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent

research entity, led a multidisciplinary evaluation of the

interference between portable wireless devices and implanted

cardiac pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the

pacemaker.

• Should NOT place wireless devices directly over the

pacemaker, such as in a breast pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with

pacemakers from other persons using wireless devices.

Electromagnetic ﬁelds (EMF)

This VTech product complies with all standards regarding

electromagnetic ﬁelds (EMF). If handled properly and

according to the instructions in this user’s manual, the product is

safe to be used based on scientiﬁc evidence available today.

User’s

manual

Charge the battery

This portable soother has a built-in

rechargeable battery for cordless usage.

To charge the battery, connect the soother

with the adaptor provided to a power source.

• Make sure the soother and the adaptor

are out of reach of children while charging.

• The soother battery is fully charged after

• 12 hours of continuous charging.

Position the soother

• This is not a toy. Do not let your baby

play with the product.

• Keep the soother out of the reach

of your baby. Never place or attach

the soother inside the baby’s crib or

playpen.

You can use the tail on the soother or the

additional strap provided to hang and attach

the soother to almost anywhere, e.g. stroller

handle, doorknob, diaper bag straps, etc.

Using the tail

Use the tail to hook the soother on a desired

object to keep it in position.

NOTES

Sa lugn a it on

Hazadr

Keep thi sco d

r ou tof erach of child ern.

The co dr needs ot be a

tleas t ht e

re fee

away from ht e child a

tall i

tme .s oD no t

use iw h

t an ex et nsion cod

r. Do not

er move h

t i

s a

tg.

Éloignez ce cod

r on des enfans

t . Le

cod

ron doi tse tor uve rà au moins trosi

pieds d’un enfan

te tce, en tou

tet mps.

’Nutilie

sz pas de rallonge. Ne retirez pas

cette étiquette.

Mantenga et

se cable fuea

r de la alcance

de los niños. Et

se cable debe et

sar por

lo menos tres pies fue ar de la alcance

del niño en todo momento. oN lo use

con una extensión inalámbrica. No qui et

esta etiqueat .

iR e

d’étrangle e

m tn

Riegs oed

estra g

n ulación

* The DC LPS power adapter is not pro -

vided in the package.

CAUTIONS

Adjust parent unit speaker volume

The speaker volume is preset to level 3, and the maximum

volume is level 5. You can adjust it to your preferred volume

level.

• Press or on the parent unit to adjust the speaker volume.

Note

• If you continue to press or when the volume reaches the

minimum or maximum setting, the parent unit will beep twice.

To mute the speaker volume:

• Press repeatedly until the volume reaches the minimum.

Notes

• When the parent unit is in mute, the visual sound indicator will still

indicate the sound detected from the soother.

• To unmute, press repeatedly until it reaches your desired volume.

3 Using the baby monitor (Cont’d)

Parent unit alert tones

Low battery tone • Beeps twice every 10 minutes when the battery is low.

Out of range tone • Beeps three times every 30 seconds when there is no link

between the soother and parent unit, or when the parent

unit is out of range from the soother.

CABLE MANAGEMENT

1 2 3

Soother overview

Lullaby

• Press to play or stop the lullaby.

vol-

• Press to decrease the speaker

volume.

Auto-off timer

• Press to turn on a 60-minute timer

while playing lullaby or soothing

sound. It will automatically stop

the lullaby or soothing sound after

playing for 60 minutes.

Skip

• Press to skip to the next lullaby or

soothing sound.

Tail

• Hook the soother on an object.

Dimmable soft-glow night light

Soothing sound

• Press to play or stop the soothing

sound.

vol +

• Press to increase the speaker

volume.

Dimmable soft-glow night light

•

dim light or bright light mode.

Press to turn on the night light in

ON/ OFF/ power switch

• Slide to power on or off the soother,

or use the soothing functions

on the soother only.

DC jack for battery charging only

Slot for the additional strap

Speaker

Auto-off timer light indicator

• On when the auto-off timer feature

is turned on.

• Off when the auto-off timer feature

is turned off.

Battery status light indicator

• On when the battery is being

charged.

• Flashes when the battery is low and

needs charging.

• Off when the battery is not being

charged; or the battery is fully

charged.

Use the soother

Power on or off the soother

• Slide the power switch on the right-hand side of

the soother to on or off.

NOTE

• Make sure the soother is on before using other

features.

Play the lullaby

The soother has ﬁve lullabies for you to comfort

your baby.

1. Brahms’ Lullaby

2. Rock a Bye Baby

3. Hush Little Baby

5. Twinkle Twinkle

Little Star

4. Minuet in G, Bach

• Press to start playing lullabies.

• Press to skip to the next lullaby.

• While a lullaby is playing, press again to stop

the lullaby.

NOTES

• The soother will play the lullabies continuously

unless you manually stop the lullabies or turn on

the auto-off timer feature.

• When a lullaby ends, the soother automatically

skips to the next lullaby. After the soother plays

the ﬁfth lullaby, it restarts playing from the ﬁrst

lullaby again.

Play the soothing sound

The soother has ﬁve soothing sounds for you to

comfort your baby.

1. White noise

2. Stream

3. Crickets

4. Birds

5. Heartbeat

• Press to start playing soothing sounds.

• Press to skip to the next soothing sound.

• While a soothing sound is playing,

press again to stop the soothing sound.

NOTE

• The soother will play the soothing sounds

continuously unless you manually stop the soothing

sounds or turn on the auto-off timer feature.

• The soother will repeat the same soothing sound

again and again unless you skip to the other

soothing sounds.

Adjust the speaker volume

• Press vol- or vol+ at any time.

NOTES

• The soother beeps to notify you when the

speaker volume is already at the highest or lowest

setting while adjusting.

Turn on or off the auto-off timer

While the soother is playing a lullaby or soothing

sound, the auto-off timer feature helps you

automatically stop the lullaby or soothing sound

after playing for 60 minutes.

1. While a lullaby or soothing sound is playing,

press to turn on the auto-off timer feature.

• The soother starts counting down 60

minutes. The auto-off timer light indicator on

the left-hand side of the soother turns on.

2. After 60 minutes, the soother will automatically

stop any lullaby or soothing sound. The auto-

off timer feature and the corresponding light

indicator will turn off.

NOTE

• You can only turn on the auto-off timer feature

when the soother is playing a lullaby or soothing

sound.

• The auto-off timer feature will not power off the

soother after the 60-minute countdown.

• You can press again to turn off the auto-off

timer feature during the 60-minute countdown.

• If you manually stop the lullaby or soothing sound

while the auto-off timer is counting down, the

auto-off timer will turn off.

Turn on or off the dimmable soft-glow night light

When the soother is on, press repeatedly to

choose from below night light options:

• Turn on the night light in dim light mode, or

• Turn on the night light in bright light mode, or

• Turn off the night light.

NOTES

• The night light will be automatically off after

15 minutes.

This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby

monitor is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install

and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is

paired to soothers, the CEC battery charging testing mode is activated while it is powered off and charging.

To keep this product working well and looking good, follow these guidelines:

• Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or

ﬂuorescent lamps).

• DO NOT expose it to direct sunlight or moisture.

• Avoid dropping the product or treating it roughly.

• Clean with a soft cloth.

• DO NOT immerse the parent unit and the soother in water and do not clean them under the tap.

• DO NOT use cleaning spray or liquid cleaners.

• Make sure the soother and parent unit are dry before you connect them to the mains again.

When you are not going to use the baby monitor for some time, store the parent unit, the soother and the

adapters in a cool and dry place.

Below are the questions most frequently asked about the baby monitor. If you cannot ﬁnd the answer to your question,

visit our website at www.vtechphones.com, or contact 1 (800) 595-9511 for customer service.

Why doesn’t the POWER

light on the soother turn on

when I switch on the units?

Perhaps the soother is not connected to the power supply. Connect the soother to

power supply. The soother turns on.

Why doesn’t the POWER

/ LINK light on the parent

unit turn on when I switch

on the units?

Perhaps the battery of the parent unit is depleted and the parent unit is not connected

to power supply. Connect the parent unit to power supply and charge the parent unit

battery. The parent unit turns on and establishes connection with the soother.

Why does the baby

monitor not respond

normally?

Try the following (in the order listed) for common cure:

1. Disconnect the power to the soothers and the parent unit.

2. Remove the battery from the parent unit.

3. Connect the soother to the power supply again. The soother turns on.

4. Connect the parent unit to the power supply again. The parent unit turns on.

5. Wait for the parent unit to synchronize with the soothers. Allow up to one minute for

this to take place.

6. Press or to adjust the speaker volume on the parent unit.

Why does the baby

monitor produce a

high-pitched noise?

The parent units and soother may be too close to each other.

• Move the parent unit away from the soothers until the noise stops; OR

• Turn down the volume of your parent unit.

Why does the parent unit

beep?

The parent unit beeps three times every 30 seconds when the soother is out of range.

Move the parent units closer to the soother (but not less than 3 feet).

The parent unit may not have enough charge for the parent unit to perform normally.

Charge the battery in the parent unit for at least 30 minutes.

Why don’t I hear a sound/

Why can’t I hear my baby

cry?

Make sure that both soother and parent unit are on. If you see the visual sound indicators

light up, but there is no sound, then you may have muted the volume or set it to a lower

level. Adjust the volume to a higher level.

If the visual sound indicators do not light up, and you cannot hear any sound, it is because

the sound is too low for the soother to detect. This is normal. Place the soother at least

3 feet / 1 meter away from your baby.

Why does the light on

the parent unit ﬂash?

The parent unit beeps twice every 10 minutes and the light ﬂashes in red when the

battery is low. Connect the parent unit to the power supply and charge the battery for at

least 30 minutes.

Why can’t I establish a

connection? Why is the

connection lost every now

and then? Why are there

sound interruptions?

The soother may be out of range. Move the parent units closer to the soother (but not

less than 3 feet).

Other electronic products may cause interference with your baby monitor. Try installing

your baby monitor as far away from these electronic devices as possible.

Frequently asked questions

California Energy Commission battery

charging testing mode

General product care

Storage

Parent unit overview

1Visual sound indicators

The visual sound indicators can show

the sound level detected by the

soother or the volume level during

speaker volume setting.

Sound level detected by the soother

•

One to three green lights indicate a

moderate sound level detected by

the soother .

•

Additional red lights indicate a

higher sound level detected by the

soother (e.g. baby crying loudly).

Speaker volume level

•

One to three green lights indicate

Level 1 to Level 3 of the speaker

volume setting.

•

Additional red lights indicate Level

4 to Level 5 of the speaker volume

setting.

2POWER / LINK

• Lights on steadily in green when

the parent unit is on and linked to

the soother.

• Flashes in green when there is no link

between the soother and parent

unit, or when the parent unit is out of

range from the soother.

• Steady on in red when the parent

unit is charging.

• Flashes in red when the battery is low.

4 (Volume down)

• Press to decrease the parent unit

speaker volume.

5Belt clip

6 (On/off)

• Press and hold to turn on or off the

parent unit.

7Power jack

8 (Volume up)

• Press to increase the parent unit

speaker volume.

9Speaker

The RBRC seal on the Ni-MH battery indicates that VTech Communications, Inc. is voluntarily participating in

an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of

service within the United States and Canada.

The program provides a convenient alternative to placing used Ni-MH batteries into the trash or municipal

waste, which may be illegal in your area.

VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the program or at

authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Ni-MH battery recycling and

disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our

environment and conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.

The RBRC seal

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the

holder of a valid proof of purchase (“Consumer” or “you”)

that the Product and all accessories provided in the sales

package (“Product”) are free from defects in material

and workmanship, pursuant to the following terms and

conditions, when installed and used normally and in

accordance with the Product operating instructions. This

limited warranty extends only to the Consumer for Products

purchased and used in the United States of America and

Canada.

What will VTech do if the Product is not free from defects

in materials and workmanship during the limited warranty

period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized

service representative will replace at VTech’s option, without

charge, a Materially Defective Product. If we choose to

replace the Product, we may replace it with a new or

refurbished Product of the same or similar design. We will

retain defective parts, modules, or equipment. Replacement

of the Product, at VTech’s option, is your exclusive remedy.

VTech will return the replacement Products to you in

working condition. You should expect the replacement to

take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for

ONE (1) YEAR from the date of purchase (90 days on

products purchased as Refurbished*). This limited warranty

also applies to the replacement Product for a period of

either (a) 90 days from the date the replacement Product

is shipped to you or (b) the time remaining on the original

one-year warranty (90-day limited warranty on products

that are purchased as Refurbished*); whichever is longer.

*Refurbished products purchased from our online store

carry a 90-day replacement warranty.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident,

shipping or other physical damage, improper installation,

abnormal operation or handling, neglect, inundation,

ﬁre, water or other liquid intrusion; or

2. Product that has been damaged due to repair, alteration

or modiﬁcation by anyone other than an authorized

service representative of VTech; or

3. Product to the extent that the problem experienced is

caused by signal conditions, network reliability, or cable or

antenna systems; or

4. Product to the extent that the problem is caused by use

with non-VTech accessories; or

5. Product whose warranty/quality stickers, product serial

number plates or electronic serial numbers have been

removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for repair

from outside the United States of America or Canada, or

used for commercial or institutional purposes (including

but not limited to Products used for rental purposes); or

7. Product returned without a valid proof of purchase (see

item 2 below); or

8. Charges for installation or set up, adjustment of customer

controls, and installation or repair of systems outside the

unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit our

website at www.vtechphones.com or call 1 (800) 595-

9511. In Canada, go to www.vtechcanada.com or call

1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s

manual - a check of the Product’s controls and features may

save you a service call.

Except as provided by applicable law, you assume the risk

of loss or damage during transit and transportation and are

responsible for delivery or handling charges incurred in the

transport of the Product(s) to the service location. VTech

will return replaced Product under this limited warranty.

Transportation, delivery or handling charges are prepaid.

VTech assumes no risk for damage or loss of the Product in

transit.

What must you return with the Product to get warranty

service?

1. Return the entire original package and contents

including the Product to the VTech service location along

with a description of the malfunction or difﬁculty; and

2. Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model) and

the date of purchase or receipt; and

3. Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement

between you and VTech. It supersedes all other written or

oral communications related to this Product. VTech provides

no other warranties for this Product. The warranty exclusively

describes all of VTech’s responsibilities regarding the

Product. There are no other express warranties. No one is

authorized to make modiﬁcations to this limited warranty and

you should not rely on any such modiﬁcation. State/Provincial

Law Rights: This warranty gives you speciﬁc legal rights, and

you may also have other rights, which vary from state to state

or province to province.

Limitations: Implied warranties, including those of ﬁtness

for a particular purpose and merchantability (an unwritten

warranty that the Product is ﬁt for ordinary use) are limited

to one year from the date of purchase. Some states/

provinces do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you.

In no event shall VTech be liable for any indirect, special,

incidental, consequential, or similar damages (including,

but not limited to lost proﬁts or revenue, inability to use

the Product or other associated equipment, the cost of

substitute equipment, and claims by third parties) resulting

from the use of this Product. Some states/provinces

do not allow the exclusion or limitation of incidental

or consequential damages, so the above limitation or

exclusion may not apply to you.

Please retain your original sales receipt as proof

of purchase.

Limited warranty

FCC Part 15

This equipment has been tested and found to comply with

the requirements for a Class B digital device under Part 15 of

the Federal Communications Commission (FCC) rules. These

requirements are intended to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio commu-

nications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television recep-

tion, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

WARNING: Changes or modiﬁcations to this equipment not

expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

FCC and IC regulations

Disclaimer and Limitation of Liability

VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the use

of this user’s manual. VTech Communications, Inc. and its suppliers assume no responsibility for any loss or claims by

third parties that may arise through the use of this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States

Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada

This device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

This Class B digital apparatus complies with Canadian require-

ment:

CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s)

that comply with Innovation, Science and Economic Devel-

opment Canada’s licence-exempt RSS(s). Operation is subject

to the following two conditions: (1) This device may not cause

interference. (2) This device must accept any interference,

including interference that may cause undesired operation of

the device.

The term ‘’IC:‘’ before the certiﬁcation/registration number only

signiﬁes that the Industry Canada technical speciﬁcations were

met.

This product meets the applicable Innovation, Science and

Economic Development Canada technical speciﬁcations.

RF radiation exposure statement

The device has been tested and complies with FCC and IC

SAR limits.

Mesures de sécurité importantes

La plaque signalétique appliquée se trouve dans le compartiment à

piles des unités bébé et parents.

Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines

mesures de précaution de base aﬁn de réduire les risques d’incendie,

d’électrocution et de blessures corporelles, dont ceux qui suivent :

1. Observez toutes les instructions et mises en garde inscrites sur

l’appareil.

2. L’installation par un adulte est requise.

3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur

supérieure à 2 mètres.

4. Ce produit ne remplace pas la surveillance adulte du nourrisson.

La supervision du nourrisson est la responsabilité du parent ou

de la personne qui s’occupe de l’enfant. Ce produit pourrait

cesser de fonctionner et, par conséquent, vous ne devriez pas

présumer qu’il continuera de fonctionner correctement pendant

une période de temps donnée. De plus, il ne s’agit pas d’un

instrument médical et ne devrait pas être utilisé comme tel. Ce

produit est destiné à vous aider à superviser votre bébé.

5. N’utilisez pas cet appareil près de l’eau ni de toute autre source

d’humidité, par exemple, près d’une baignoire, cuve à lessive,

évier de cuisine, dans un sous-sol humide ni près d’une piscine,

dans un soussol humide ou une douche.

6. MISE EN GARDE: Utilisez uniquement la pile fournie. Un risque

d’explosion pourrait survenir si un mauvais type de pile est

utilisé pour l’unité du parent. La pile ne peut pas être soumise

à des températures extrêmes élevées ou basses et à une faible

pression d’air à haute altitude pendant l’utilisation, l’entreposage

ou le transport. L’élimination de la pile dans le feu ou dans un

four chaud, ou l’écrasement ou le découpage mécanique de

la pile peuvent entraîner une explosion. Laisser la pile dans

un environnement à température extrêmement élevée peut

entraîner une explosion ou la fuite d’un liquide ou d’un gaz

inﬂammable. Une pile soumise à une pression d’air extrêmement

basse peut provoquer une explosion ou une fuite de liquide ou

de gaz inﬂammable. Éliminer la pile usagée conformément aux

informations du Sceau RBRC.

7. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation

d’un adaptateur dont la polarité ou la tension serait inadéquate

risque d’endommager sérieusement le produit et mettre

Sortie : 6V DC 400mA / 5V DC 400mA

VTECH TELECOMMUNICATIONS LTD.

Modèle : VT05UUS06040 / VT05EUS05040

Informations sur les piles rechargeables :

2.4V NiMH battery

YIYANG CORUN BATTERY CO LTD.

Modèle : NI-MHAAA400×2-FF

8. Lorsqu’ils sont branchés dans une prise de courant, les

adaptateurs secteur ont été conçus pour être orientés

correctement, soit à la verticale ou au plancher. Les broches n’ont

pas été conçues pour supporter le poids du bloc d’alimentation

et le maintenir en place si celuici est branché dans une prise au

plafond, sous une table ou dans un meuble.

9. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la

prise de courant doit être installée près du produit, aﬁn d’assurer

une accessibilité sécuritaire à la prise de courant.

10. Débranchez ce produit de la prise de courant avant de procéder

au nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un

chiffon humide pour le nettoyer.

11. Débranchez les cordons d’alimentation avant de remplacer le

bloc-piles.

12. Ne coupez pas les cordons d’alimentation pour remplacer les

ﬁches, car ceci peut présenter un danger potentiel.

13. Ne laissez aucun objet reposer ni appuyer sur le cordon

d’alimentation. N’installez pas cet appareil dans un endroit où l’on

risque d’écraser le cordon d’alimentation ou de le piétiner.

14. Ne faites fonctionner cet appareil qu’avec le type d’alimentation

indiqué sur l’étiquette. Si vous ne connaissez pas le type

d’alimentation que vous possédez à votre domicile, consultez

votre marchand ou votre compagnie locale d’électricité.

15. Ne surchargez pas les prises de courant murales ni les rallonges

électriques.

16. Ne placez pas cet appareil sur un chariot, meuble, trépied,

support de montage ni table chancelants.

17. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil

ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de

surchauffer, ne bloquez sous aucun prétexte ces ouvertures et

n’empêchez pas l’aération adéquate de l’appareil en le plaçant sur

un lit, divan, tapis ou toute autre surface similaire. De même, ne le

positionnez pas à proximité ni au-dessus d’une source de chaleur

ou d’un calorifère. De plus, ne placez pas l’appareil dans un endroit

avant de vous assurer qu’il y ait une bonne circulation d’air.

18. N’enfoncez jamais d’objets à travers les ouvertures de cet

appareil, car ils pourraient entrer en contact avec des points de

tension dangereux ou causer des courts-circuits qui peuvent

dégénérer en incendies ou en risques d’électrocution. Ne

renversez jamais de liquide dans ce produit.

19. Aﬁn de réduire les risques d’électrocution, ne démontez pas cet

appareil, mais apportez-le dans un centre de service autorisé.

L’ouverture du boîtier ou le retrait de toutes pièces que contient

cet appareil, à l’exception de l’accès autorisé à certaines portes

ou ouvertures, risque de vous exposer à des points de tension

dangereux ou d’autres dangers. Un remontage incorrect peut par

la suite présenter des risques d’électrocution.

20. Vous devriez tester la réception chaque fois que vous mettez

l’appareil en fonction.

21. Examinez les composantes aﬁn de vériﬁer si celles-ci ne sont pas

endommagées.

22. Il existe un très faible risque de perte de conﬁdentialité avec

certains appareils électroniques (autres écoute-bébés, téléphones

sans ﬁls etc.). Pour l’éviter, s’assurer que le produit n’a jamais

été utilisé avant l’achat, réinitialiser l’unité de façon périodique,

éteindre l’écoute-bébé quand il n’est pas en cours d’utilisation.

23. Les enfants devraient être supervisés aﬁn de vous assurer qu’ils ne

jouent pas avec l’appareil.

24. Le produit n’est pas conçu pour être utilisé par des personnes

(incluant des enfants) aux capacités physiques, sensorielles

ou mentales réduites ou qui manquent d’expérience et de

connaissances, à moins qu’on leur ait donné sufﬁsamment

de supervision ou d’instructions relativement à l’utilisation de

l’appareil par une personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

1. Utilisez et entreposez le produit à une température entre 0˚ C

(32˚F) et 40˚C (104˚ F).

2. N’exposez pas cet appareil à des froids ou des chaleurs extrêmes,

ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une

source de chauffage.

3. Le bloc-piles ne doit pas être exposé à la chaleur excessive telle

que la lumière du soleil ou au feu.

4. Avertissement - Risque de strangulation -

Les enfants se sont ÉTRANGLÉS dans des cordons.

Gardez ce cordon hors de portée des enfants (à

plus de 0,9 m). N’enlevez pas cette étiquette.

5. Ne jamais placer le moniteur à l’intérieur du

berceau ou du parc de bébé. Ne jamais couvrir le moniteur

ou l’unité (s) portative avec un article tel une serviette ou une

couverture.

6. D’autres équipements électroniques peuvent produire des

interférences sur votre moniteur vidéo et audio. Tentez

d’installer votre moniteur vidéo ou audio à l’écart des appareils

électroniques tels que des routeurs sans ﬁl, radios, téléphones

cellulaires, interphones, moniteurs, téléphones, ordinateurs

personnels, électroménagers et téléphones sans ﬁl.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs numériques

sans ﬁl) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une ﬁrme de

recherche indépendante, a mené une évaluation pluridisciplinaire des

interférences entre les téléphones sans ﬁl portatifs et les stimulateurs

cardiaques implantés dans l’organisme. Appuyée par l’Administration

des aliments et drogues (FDA) des États-Unis, la ﬁrme WTR

recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Vous devriez maintenir les dispositifs sans ﬁl à au moins six pouces

du simulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl directement sur

le stimulateur cardiaque, tel que dans une poche de chemise,

lorsque celui-ci est en marche.

L’étude effectuée par l’organisme WRS n’a pas identiﬁé de risque

pour les détenteurs de simulateurs cardiaques causés par les gens qui

utilisent dispositifs sans ﬁl à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes les normes se rapportant

aux champs électromagnétiques (EMF) standard. Si vous le manipulez

correctement en suivant les instructions de ce guide, son utilisation

sera sécuritaire pendant de nombreuses années, selon les meilleures

évidences scientiﬁques dont nous disposons aujourd’hui.

For cETL compliance only

VTech DM1411 Guide de démarrage rapide

Marque: VTech

Modèle: DM1411

Catégorie: Moniteurs vidéo bébé

Taper: Guide de démarrage rapide

Télécharger le PDF

rapport

dans d''autres langues

English: VTech DM1411 Quick start guide

VTech DM1411 Guide de démarrage rapide

VTech DM1411 Guide de démarrage rapide

dans d''autres langues

Documents connexes