Positioning Universal FT5000MW Mode d'emploi

FT5000MW
Marque
Positioning Universal
Modèle
FT5000MW
Taper
Mode d'emploi
Key Value Proposition Future Capabilities
Capabilities
In-cab workhorse – Apoc 20 / FT5000MW
•
Versatile, under dash device:
•
cars & trucks in single device
•
most common utility features
•
Internal antennas
•
Driver Behavior
•
ELD
•
Light, Medium, Heavy Duty Diagnostics
•
Leased and Rental Vehicle Recovery
•
Motion Detection
•
High Frequency Tracking
•
Vehicle Diagnostics (ISO-15765, J1939)
•
Ignition Detection
•
Starter Disable (via relay)
•
Operator ID (1-wire)
FLEX CONFIDENTIAL – DO NOT DISCLOSE
Applications
In-cab workhorse - Apoc 20 / FT5000MW
Location
GPS (multi-constellation)
Assisted acquisition: 2s (via cloud)
Acquisition Sensitivity: -160dBm (1)
Tracking Sensitivity: -167dBm (2)
Internal Sensors
6-axis IMU
System temperature
Battery level
Internal Antennas
Cellular
GPS
Bluetooth
External Connectors
Power in (6-48VDC)
1-Wire
Digital Input x4
Digital Output x3
CAN 2.0B x1 (ISO-15765 or J1939)
RS-232
ISO-9141 (K line for Tachometer)
J1708
Battery
Global Cellular Connectivity
4G , Global Bands 2G:
850,900,1800,1900
Local Area Connectivity
BLE: 5.0 (master, slave, LE data packet length)
Operating Temperature
Powered: -40˚C – 70˚C
Battery: -20˚C – 60˚C
Charging: 0˚C – 45˚C
Housing
Industrial grade Polycarbonate (PC)
Ingress Protection (IP): 4X
Security
Secure boot
TLS/SSL
FIPS 140-2 (Optional upgrade)
Certifications
FCC, IC, CE, PTCRB, RCM
Environmental
RoHS, Reach, SAEJ1455 [Thermal Shock (4), Humidity
(5), Mechanical Vibration, Mechanical Shock,
Electrostatic Discharge]
Dimensions
6.33” x 2.6” x 1” (151mm x 66mm x 25mm)
Weight
TBC
FLEX CONFIDENTIAL – DO NOT DISCLOSE
Ah
User Interface
Multi-color LED
Buzzer
(1) (2) Based on GPS chipset specification
(4) (5) Inside operating temperature range
FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiated
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party
responsible for compliance could void the user‘s authority to operate the
equipment.
RF Exposure Information
This device meets the government’s requirements for exposure to radio
waves.
This device is designed and manufactured not to exceed the emission limits
for exposure to radio frequency (RF) energy set by the Federal
Communications Commission of the U.S. Government.
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall
not be less than 20cm (8 inches) during normal operation.
ISED Notice
This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR Innovation, Sciences et Développement économique Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
This device complies with the Canadian ICES-003 Class B specifications. CAN ICES-003(B)/ NMB-003(B)
ISED RF Exposure Statement
This device complies with ISED RSS-102 RF exposure limits set forth for an uncontrolled environment. In order to
avoid the possibility of exceeding the IC RSS-102 RF exposure limits, human proximity to the antenna shall not be
less than 20cm (8 inches) during normal operation.
Cet appareil est conforme aux limites d'exposition aux rayonnements de la CNR-102 définies pour un environnement
non contrôlé. Afin d'éviter la possibilité de dépasser les limites d'exposition aux fréquences radio de la CNR-102, la
proximité humaine à l'antenne ne doit pas être inférieure à 20 cm (8 pouces) pendant le fonctionnement normal.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Positioning Universal FT5000MW Mode d'emploi

FT5000MW
Marque
Positioning Universal
Modèle
FT5000MW
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Autres documents