Danby DAC060EB7WDB Le manuel du propriétaire

Marque: Danby

Modèle: DAC060EB7WDB

Taper: Le manuel du propriétaire

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE

MANUAL DEL PROPIETARIO

www.Danby.com

2019.12.05

MODEL • MODÈLE • MODELO

DAC060EB7WDB

AIR CONDITIONER

Owner’s Manual.............................1 - 16

CLIMATISEUR

Manual du propriétaire.................17 - 32

AIRE ACONDICIONADO

Manual del propietario..................33 - 48

Welcome

Welcome to the Danby family. We are proud of our quality products and we believe in

dependable service. We suggest that you read this owner’s manual before plugging in your new

appliance as it contains important operation information, safety information, troubleshooting and

maintenance tips to ensure the reliability and longevity of your appliance.

Visit www.Danby.com to access self service tools, FAQs and much more. For additional assistance

call 1-800-263-2629.

Note the information below; you will need this information to obtain service under warranty.

You must provide the original purchase receipt to validate your warranty and receive service.

Model Number: _________________________________________________

Serial Number: _________________________________________________

Date of Purchase: _______________________________________________

Need Help?

Before you call for service, here are a few things you can do to help us serve you better.

Read this owner’s manual:

It contains instructions to help you use and maintain your appliance properly.

If you receive a damaged appliance:

Immediately contact the retailer or builder that sold you the appliance.

Save time and money:

Check the troubleshooting section at the end of this manual before calling. This section

will help you solve common problems that may occur.

1-800-26- Danby

(1-800-263-2629)

SAVE THESE INSTRUCTIONS!

CAUTION: RISK OF FIRE

Flammable refrigerant used. When maintaining

or disposing of the air conditioner, the refrigerant

must not be allowed to vent into the open air.

SAFETY REQUIREMENTS

DANGER: Risk of ﬁ re or explosion. Flammable

refrigerant used. Do not damage the refrigerant

circuit.

• Ensure that servicing is done by factory

authorized service personnel, to minimize

product damage or safety issues.

• Consult repair manual or owner’s guide before

attempting to service this product. All safety

precautions must be followed.

• Dispose of properly in accordance with federal

or local regulations.

• Follow handling instructions carefully.

• Keep ventilation openings, in the appliance clear

of obstruction.

• Do not use mechanical devices or other means

to accelerate the defrosting process.

• Children should be supervised to ensure that

they do not play with the appliance.

• Do not store or install the appliance near

continuously operating ignition sources such as

open ﬂ ames or a gas stove.

• Do not operate near water or in a wet room.

• Do not pierce or burn.

• Be aware that refrigerants may not contain an

odor.

• The appliance must be stored so as to prevent

mechanical damage from occurring.

All wiring must comply with local and national

codes and must be installed by a qualiﬁ ed

electrician. Check the available power supply and

resolve any wiring problems before installing and

operating this appliance.

The rating plate located on the right side of the

appliance just above the power cord contains

electrical and other technical data.

This appliance is not intended for use by persons

(including children) whose physical, sensory or

mental capabilities may be different or reduced,

or who lack experience or knowledge, unless such

persons receive supervision or training to operate

the appliance by a person responsible for their

safety.

GROUNDING INSTRUCTIONS

This appliance must be grounded. Grounding

reduces the risk of electrical shock by providing an

escape wire for the electrical current.

This appliance has a cord that has a grounding

wire with a 3-prong plug. The power cord must be

plugged into an outlet that is properly grounded.

If the outlet is a 2-prong wall outlet, it must be

replaced with a properly grounded 3-prong wall

outlet. The serial rating plate indicates the voltage

and frequency the appliance is designed for.

WARNING - Improper use of the grounding

plug can result in a risk of electric shock.

Consult a qualiﬁ ed electrician or service agent

if the grounding instructions are not completely

understood, or if doubt exists as to whether the

appliance is properly grounded.

Do not connect your appliance to extension

cords or together with another appliance in the

same wall outlet. Do not splice the power cord.

Do not under any circumstances cut or remove the

third ground prong from the power cord. Do not

use extension cords or ungrounded (two prongs)

adapters.

If the power supply cord is damaged, it must be

replaced by the manufacturer, its service agent or

similar qualiﬁ ed person in order to avoid hazard.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Any person involved with working on the refrigerant

circuit should hold a current, valid certiﬁ cate from

an industry accredited assessment authority which

authorizes their competence to handle refrigerants

safely in accordance with an industry recognized

assessment speciﬁ cation.

Servicing shall only be performed as recommended

by the manufacturer. Maintenance and repair

requiring the assistance of other skilled personnel

shall be carried out under the supervision of

the person competent in the use of ﬂ ammable

refrigerants.

When maintaining or disposing of the appliance the

refrigerant must be recovered properly and should

not be allowed to discharge to the air directly.

Information on servicing

1. Checks to the area: Prior to beginning work

on systems containing ﬂ ammable refrigerants,

safety checks are necessary to ensure that the

risk of ignition is minimized. For repair to the

refrigerating system, the following precautions

shall be complied with prior to conducting work

on the system.

2. Work procedure: Work shall be undertaken

under a controlled procedure so as to minimize

the risk of a ﬂ ammable gas or vapour being

present while the work is being performed.

3. General work area: All maintenance staff

and others working in the local area shall

be instructed on the nature of work being

carried out. Work in conﬁ ned spaces shall be

avoided. The area around the work space shall

be sectioned off. Ensure that the conditions

within the work area have been made safe by

removing all ﬂ ammable material.

4. Checking for the presence of refrigerant:

The are shall be checked with an appropriate

refrigerant detector prior to and during work

to ensure the technician is aware of potentially

ﬂ ammable atmospheres. Ensure that the leak

detection equipment being used is suitable

for use with ﬂ ammable refrigerants, i.e. non-

sparking, adequately sealed and intrinsically

safe.

5. Presence of ﬁ re extinguisher: If any hot work is

to be conducted on the refrigeration equipment

or any associated parts, appropriate ﬁ re

extinguishing equipment shall be available

to hand. Have a dry powder or C0

ﬁ re

extinguisher adjacent to the work area.

6. No ignition sources: No person carrying out

work in relation to a refrigeration system which

involves exposing any pipe work that contains

or has contained ﬂ ammable refrigerant shall use

any sources of ignition in such a manner that it

may lead to risk of ﬁ re or explosion. All possible

ignition sources including cigarette smoking,

should be kept sufﬁ ciently far away from the

site of installation, repairing, removing and

disposal during which ﬂ ammable refrigerant can

possibly be released to the surrounding space.

Prior to work taking place, the area around the

equipment is to be surveyed to make sure there

are no ﬂ ammable hazards or ignition risks. No

smoking signs shall be displayed.

7. Ventilated area: Ensure that the area is in the

open or that it is adequately ventilated before

breaking into the system or conducting any hot

work. A degree of ventilation shall continue

during the period that the work is carried out.

The ventilation should safely disperse any

released refrigerant and preferable expel it

externally into the atmosphere.

8. Checks to the refrigeration equipment: Where

electrical components are being changed, they

shall be ﬁ t for the purpose and to the correct

speciﬁ cation. At all times the manufacturer’s

maintenance and service guidelines shall be

followed. If in doubt consult the manufacturer’s

technical department for assistance.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

The following checks shall be applied to installations

using ﬂ ammable refrigerants:

• The charge size is in accordance with the room

size within which the refrigerant containing

parts are installed.

• The ventilation machinery and outlets are

operating adequately and are not obstructed.

• If an indirect refrigerating circuit is being used,

the secondary circuit shall be checked for the

presence of refrigerant.

• Marking to the equipment continues to be visible

and legible. Markings and signs that become

illegible must be corrected.

• Refrigeration pipe or components are installed in

a position where they are unlikely to be exposed

to any substance which may corrode refrigerant

containing components, unless the components

are constructed of materials which are inherently

resistant to being corroded or are suitable

protected against being corroded.

9. Checks to electrical devices: Repair and

maintenance to electrical components shall

include initial safety checks and component

inspection procedures. If a fault exists that

could compromise safety, then no electrical

supply shall be connected to the circuit until it

is satisfactorily dealt with. If the fault cannot

be corrected immediately but it is necessary to

continue operation, an adequate temporary

solution shall be used. This shall be reported to

the owner of the equipment so all parties are

advised.

Initial safety checks shall include:

• That capacitors are discharged. This shall be

done in a safe manner to avoid possibility of

sparking.

• That no live electrical components and wiring

are exposed while charging, recovering or

purging the system.

• That there is continuity of earth bonding.

Repairs to sealed components

1. During repairs to sealed components, all

electrical supplies shall be disconnected from

the equipment being worked upon prior to any

removal of sealed covers, etc. If it is absolutely

necessary to have an electrical supply to

equipment during servicing then a permanently

operating form of leak detection shall be located

at the most critical point to warn of a potentially

hazardous situation.

2. To ensure that by working on electrical

components the casing is not altered in such

a way that the level of protection is affected,

particular attention shall be paid to the

following:

• Damage to cables, excessive number of

connections, terminals not made to original

speciﬁ cation, damage to seals, incorrect ﬁ tting

of glands, etc.

• Ensure the apparatus is mounted securely.

• Ensure that seals or sealing materials have

not degraded such that they no longer serve

the purpose of preventing the ingress of

ﬂ ammable atmospheres. Replacement parts

shall be in accordance with the manufacturer’s

speciﬁ cations.

Note: The use of silicon sealant may inhibit the

effectiveness of some types of leak detection

equipment. Intrinsically safe components do not

have to be isolated prior to working on them.

Repair to intrinsically safe components

Do not apply any permanent inductive or

capacitance loads to the circuit without ensuring

that this will not exceed the permissible voltage

and current permitted for the equipment in use.

Intrinsically safe components are the only types that

can be worked on while live in the presence of a

ﬂ ammable atmosphere. The test apparatus shall

be at the correct rating. Replace components only

with parts speciﬁ ed by the manufacturer. Other

parts may result in the ignition of refrigerant in the

atmosphere from a leak.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Removal and evacuation

When breaking into the refrigerant circuit to make

repairs or for any other purpose conventional

procedures shall be used. However, it is important

that the best practice is followed since ﬂ ammability

is a consideration. The following procedures shall

be adhered to:

• Remove refrigerant.

• Purge the circuit with inert gas.

• Evacuate.

• Purge again with inert gas.

• Open the circuit by cutting or brazing.

• The refrigerant charge shall be recovered into

the correct recovery cylinders. The system shall

be ﬂ ushed with OFN to render the unit safe. This

process may need to be repeated several times.

Compressed air or oxygen shall not be used for

this task.

• Flushing shall be achieved by breaking the

vacuum in the system with OFN and continuing

to ﬁ ll until the working pressure is achieved, then

venting to atmosphere and ﬁ nally pulling down

to a vacuum. This process shall be repeated until

no refrigerant is within the system. When the

ﬁ nal OFN charge is used, the system shall be

vented down to atmospheric pressure to enable

work to take place. This operation is absolutely

vital is brazing operations on the pipe-work are

to take place.

• Ensure that the outlet for the vacuum pump is

not close to any ignition sources and there is

ventilation available.

Charging procedures

In addition to conventional charging procedures, the

following requirements shall be followed:

• Ensure that contamination of different

refrigerants does not occur when using charging

equipment. Hoses or lines shall be as short as

possible to minimize the amount of refrigerant

contained in them.

• Cylinders shall be kept upright.

• Ensure that the refrigeration system is earthed

prior to charging the system with refrigerant.

• Label the system when charging is complete, if

not already labeled.

• Extreme care shall be taken not to overﬁ ll the

refrigeration system.

• Prior to recharging the system it shall be

pressure tested with OFN. The system shall be

leak tested on completion of charging but prior

to commissioning. A follow up leak test shall be

carried out prior to leaving the site.

Cabling

Check that cabling will not be subject to wear,

corrosion, excessive pressure, vibration, sharp

edges or any other adverse environmental effects.

The check shall also take into account the effects of

aging or continual vibration from sources such as

compressors or fans.

Detection of ﬂ ammable refrigerants

Under no circumstances shall potential sources of

ignition be used in the searching for or detection

of refrigerant leaks. A halide torch or any other

detector using a naked ﬂ ame shall not be used.

Leak detection methods

The following leak detection methods are deemed

acceptable for systems containing ﬂ ammable

refrigerants:

• Electronic leak detectors shall be used to detect

ﬂ ammable refrigerants but the sensitivity may

not be adequate or may need recalibration.

Detection equipment shall be calibrated in a

refrigerant-free area. Ensure that the detector is

not a potential source of ignition and is suitable

for the refrigerant used.

• Leak detection equipment shall be set at a

percentage of the LFL of the refrigerant and

shall be calibrated to the refrigerant employed

and the appropriate percentage of gas (25%

maximum) is conﬁ rmed.

• Leak detection ﬂ uids are suitable for use with

most refrigerants but the use of detergents

containing chlorine shall be avoided as the

chlorine may react with the refrigerant and

corrode the copper or pipe-work.

• If a leak is suspected, all naked ﬂ ames shall be

removed or extinguished.

• If a leakage of refrigerant is found which

requires brazing, all of the refrigerant shall be

recovered from the system or isolated by means

of shut off valves in a part of the system remote

from the leak. Oxygen free nitrogen (OFN) shall

then be purged through the system both before

and during the brazing process.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Decommissioning

Before carrying out this procedure, it is essential

that the technician is completely familiar with the

equipment in all its detail. It is recommended good

practice that all refrigerants are recovered safely.

Prior to the task being carried out, an oil and

refrigerant sample shall be taken in case analysis is

required prior to re-use of reclaimed refrigerant. It

is essential that electrical power is available before

the task is commenced.

A. Become familiar with the equipment and its

operation.

B. Isolate system electrically.

C. Before attempting the procedure ensure that:

• Mechanical handling equipment is available

if required for handling refrigerant cylinders.

• All personal protective equipment is

available and being used correctly.

• The recovery process is supervised at all

times by a competent person.

• Recovery equipment and cylinders conform

to the appropriate standards.

D. Pump down refrigerant system, if possible.

E. If a vacuum is not possible, make a manifold so

that refrigerant can be removed from various

parts of the system.

F. Make sure that cylinder is situated on the scales

before recovery takes place.

G. Start the recovery machine and operate in

accordance with the manufacturer’s instructions.

H. Do not overﬁ ll cylinders. No more than 80%

volume liquid charge.

I. Do not exceed the maximum working pressure

of the cylinder, even temporarily.

J. When the cylinders have been ﬁ lled correctly

and the process is completed, make sure that the

cylinders and the equipment are removed from

the site promptly and all isolation valves on the

equipment are closed off.

K. Recovered refrigerant shall not be charged into

another refrigeration system unless it has been

cleaned and checked.

Labeling

Equipment shall be labeled stating that it has been

decommissioned and emptied of refrigerant. The

label shall be dated and signed. Ensure that there

are labels on the equipment stating the equipment

contains ﬂ ammable refrigerant.

Recovery

When removing refrigerant from a system, either for

servicing or decommissioning, it is recommended

good practice that all refrigerants are removed

safely.

When transferring refrigerant into cylinders, ensure

that only appropriate refrigerant recovers cylinders

are employed. Ensure that the correct number of

cylinders for holding the total system charge are

available. All cylinders to be used are designed

for the recovered refrigerant and labeled for that

refrigerant, i.e. special cylinders for the recovery

of refrigerant. Cylinders shall be complete with

pressure relief valve and associated shut-off valves

in good working order. Empty recovery cylinders

are evacuated and, if possible, cooled before

recovery occurs.

The recovery equipment shall be in good working

order with a set of instructions concerning the

equipment that is at hand and shall be suitable for

the recovery of ﬂ ammable refrigerants. In addition,

a set of calibrated weighing scales shall be

available and in good working order. Hoses shall

be complete with leak-free disconnect couplings

and in good condition. Before using the recovery

machine, check that is it in satisfactory working

order, has been properly maintained and that any

associated electrical components are sealed to

prevent ignition in the event of a refrigerant leak.

Consult the manufacturer if in doubt.

The recovered refrigerant shall be returned to the

refrigerant supplier in the correct recovery cylinder

and the relevant waste transfer note shall be

arranged. Do not mix refrigerants in recovery units

and especially not in cylinders. If compressors or

compressor oils are to be removed, ensure that they

have been evacuated to an acceptable level to make

certain that ﬂ ammable refrigerant does not remain

within the lubricant. The evacuation process shall be

carried out prior to returning the compressor to the

suppliers. Only electric heating to the compressor

body shall be employed to accelerate this process.

When oil is drained form a system, it shall be

carried out safely.

LOCATION

This air conditioner is designed for single or double

hung windows. Since window designs vary, it may

be necessary to make some modiﬁ cations for safe

installation.

This air conditioner is not designed for vertical,

slider type windows or “through the wall”

installation.

Ensure that the window and frame are structurally

sound and free from dry or rotted wood.

Install the air conditioner in a window on a side

of the building which favors more shade than

sunlight. If the appliance must be in direct sunlight,

it is advisable to provide a shade awning over the

appliance to ensure efﬁ cient functioning.

Do not install the appliance where leakage of

combustible gas is suspected.

This appliance is designed to evaporate

condensation under normal conditions. Under

extremely hot or humid conditions, excess

condensation may overﬂ ow to the outside. The

appliance should be installed where condensation

cannot drip on pedestrians or neighboring

properties.

Provide sufﬁ cient clearance around the appliance

to allow ample air circulation. The rear of the

appliance should be outdoors, it should not be in

a garage or another room. Keep the appliance

away from obstacles and at least 76 cm (30 inches)

above the ground. Ensure that curtains and other

obstructions do not block air ﬂ ow to the appliance.

76.2 cm

(30 inches)

50.8 cm

(20 inches)

50.8 cm

(20 inches)

12 cm

(30.5 in)

INSTALLATION INSTRUCTIONS

REQUIRED TOOLS

• Screwdrivers: Phillips and ﬂ at head.

• Power Drill: 3.2mm (1/8”) diameter drill bit

• Pencil

• Measuring Tape

• Scissors

• Carpenter’s Level

ACCESSORIES

The following accessories are included with

the appliance and should be used during the

installation.

1. 13 mm (1/2 inch) screws (x7)

2. 9.5 mm (3/8 inch) screws (x4) (Factory installed

on some models.)

3. Safety Lock

4. Adhesive foam seal

5. Regular foam seal

6. “L” shaped mounting bracket (Factory installed

on some models.)

7. Bracket for wood windows (x2)

8. Bracket for vinyl windows (x2)

9. Weather stripping (x5)

10. Side curtains (x2)

2 3

INSTALLATION INSTRUCTIONS

L BRACKET

The “L” shaped bracket may come factory installed

on some models.

If the “L” shaped bracket is not pre-installed, attach

it to the top of the cabinet as shown below using the

provided 9.5 mm (3/8”) screws (x4).

INSTALLATION

Attach the side curtains to the appliance by sliding

the curtain frame into the side channel of the

cabinet. The curtains are labeled “left” and “right

on the frames. This refers to the left and right

sides of the appliance when facing the front of the

appliance.

Cut the regular foam seal to ﬁ t the area of the

window sill that the air conditioner will rest on.

Place the air conditioner into the window with the

“L” shaped mounting bracket positioned in front of

the upper sash. The bottom of the cabinet should be

positioned on the recessed portion of the window

frame. Pull the upper window sash down until it

rests just behind the front ﬂ ange of the “L” shaped

mounting bracket.

Expand the side curtains on each side and secure

the top of the frames to the window sash using one

13 mm (1/2”) screw on each side of the “L” shaped

mounting bracket.

Attach the clamps on the lower part of each curtain

to the window sill using one 13 mm (1/2”) screw on

each side of the cabinet.

Place the adhesive foam seal into the opening

between the inside and outside windows and

attached the safety lock to the outside window frame

using two 13 mm (1/2”) screws.

Check the Tilt Angle

The air conditioner should be tilted downward

towards the outside approximately 3° to 4°. This

tilt will encourage any condensed water to drain

to the outside. If any condensed water leaks to the

inside of the house, check the tilt angle and adjust

as necessary.

Measure the tilt angle from the front of the cabinet’s

edge. The difference in height between the front and

the back of the appliance, labeled “A” on the image

below, should be approximately 19 mm - 2.5 cm

(3/4” - 1”).

CONTROL PANEL

1. Remote Control Receiver: Ensure this receiver is not obscured by curtains or other items as it could

impact remote control functioning.

2. Follow Me Indicator Light: Illuminates when the Follow Me function is active. Follow Me can only be set

from the remote control.

3. Power Button: Used to turn the appliance on or off.

4. Mode Button: Used to choose the operating mode.

5. Up and Down Arrows: Used to adjust the set temperature in 1° increments and the timer function in 30

minute increments up to 10 hours and then in 1 hour increments up to 24 hours.

6. Display Panel: Displays the set temperature, the ambient temperature and the timer settings. To change

the temperature scale being displayed, press the up and down buttons at the same time.

7. Fan Button: Used to set the fan speed. The fan can be set to Low, Medium, High and Auto.

8. Wireless connect button: Used to connect to a wireless network.

9. Energy Saver Button: Used to set the energy saver function.

10. Filter Button: The indicator light will illuminate as a reminder to check the ﬁ lter. Once the ﬁ lter has been

cleaned, use this button to resume operation.

11. Sleep Button: Used to set the Sleep function.

12. Timer Button: Used to set the auto on and auto off timer.

4 5

11 12

OPERATING INSTRUCTIONS

REMOTE CONTROL

1. Display Panel: Displays the set temperature, the

ambient temperature and the timer settings. To

change the temperature scale being displayed,

press the °C/°F button.

2. Up and Down Arrows: Used to adjust the set

temperature in 1° increments and the timer

function in 30 minute increments up to 10 hours

and then in 1 hour increments up to 24 hours.

3. Mode Button: Used to choose the operating

mode.

4. Follow Me Button: Used to set the follow me

function.

5. °C/°F button: Use to change the temperature

scale.

6. LED Button: Press to turn the LED back light on

or off.

7. Power Button: Used to turn the appliance on or

off.

8. Sleep Button: Used to set the sleep function.

9. Fan Button: Used to set the fan speed. The fan

can be set to low, medium, high and auto.

10. Timer On Button: Used to set the auto on timer.

11. Timer Off Button: Used to set the auto off timer.

12. Energy Saver Button: Used to set the energy

saver function.

13. Lock Button: Press the °C/°F button and the

timer button at the same time to lock the remote

control and prevent the settings from being

inadvertently changed.

TEMP

OPERATING INSTRUCTIONS

REMOTE CONTROL BATTERIES

The remote control requires two AAA alkaline

batteries (included). Batteries should be replaced

when:

a) No sound is heard when attempting to program

the appliance.

b) The appliance does not respond to a command

issued by the remote control.

Battery replacement:

1. Slide the rear cover on the remote in the

direction of the arrow.

2. Insert two AAA batteries following the same

orientation depicted inside the battery chamber

(+/-).

3. Reinstall the rear cover.

4. If the remote control will not be used for

extended periods of time, the batteries should be

removed.

Notes:

• Protect the remote control from high

temperatures, and keep it away from radiation

exposure.

• Keep the control panel receiver out of direct

sunlight.

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc), or

rechargeable (ni-cad, ni-mh,etc) batteries.

• The remote operates within a range of 8 meters

(26 ft.) from the receiver located inside the main

appliance. Any obstruction between the receiver

and remote may cause signal interference,

limiting the ability to program the main unit.

OPERATING MODES

There are four operating modes to choose from.

Press the mode button repeatedly to choose the

desired mode. The adjacent indicator light will

illuminate to show which mode has been selected.

• Cool Mode

Choose cool mode to set the cooling function. Use

the up and down arrows to choose the desired

temperature. When cool mode is selected, the fan

speed can be adjusted by pressing the fan button.

• Dry Mode

Choose dry mode to remove excess moisture

from the air during periods of high humidity. All

water pulled from the air will condense inside the

appliance and drain out the back. The fan speed

will be automatically set and cannot be modiﬁ ed in

dry mode.

• Fan Mode

Choose fan mode to run the internal fan without

engaging the cooling function. Press the fan button

repeatedly to choose the fan speed.

• Auto Mode

Auto mode is a pre-set factory program that

automatically deﬁ nes the mode and fan speed

based on the set temperature, the ambient

temperature and the ambient humidity.

UP AND DOWN ARROWS

The up and down arrows will modify the set

temperature in 1° increments.

The up and down arrows will modify the set time of

the timer function in 0.5 hour increments up to 10

hours and then in 1 hour increments up to 24 hours

maximum.

OPERATING INSTRUCTIONS

SLEEP

The sleep function can be used to conserve energy

during sleeping hours.

When selected, the set temperature will increase

by 1°C/2°F every half hour for one full hour. The

appliance will hold the new set temperature for

6 hours before automatically returning to normal

operation.

The Sleep Function can be canceled at any time by

pressing the Sleep Button.

ENERGY SAVER

The energy saver function will automatically cycle

the fan on and off when the compressor is not in use

to minimize how often the compressor needs to turn

on.

When selected, the fan will continue to run for 3

minutes after the compressor turns off. The fan will

then cycle on for 2 minutes in 10 minute intervals

until the ambient temperature is above the set

temperature, at which point the compressor will turn

on and cooling will resume.

FOLLOW ME

There is a temperature sensor built into the remote

control that will monitor the room temperature. Keep

the remote control with you and the appliance will

automatically adjust the set temperature based on

the temperature where you are located.

The remote will display the temperature at its

location. The remote will send a signal to the air

conditioner every 3 minutes, so long as you remain

within range of the appliance.

The follow me light on the control panel will

illuminate for 5 seconds every 3 minutes to indicate

that it has received a signal from the remote. If the

appliance does not receive a signal from the remote

during any 7 minute interval it will beep to indicate

that the follow me mode has ended.

The maximum distance for the follow me feature is

8 meters (26 feet). This feature is available in cool

and auto modes.

WIRELESS CONNECTION

This appliance can be controlled with a wireless

application on your wireless device.

Visit https://www.danby.com/support/#apps

to download the application and learn about its

operation.

OPERATING INSTRUCTIONS

TIMER

The timer can be used to turn the appliance on or

off after a set period of time.

The control panel has one timer button. Press once

to set the auto off timer and twice to set the auto off

timer. The remote control has separate timer on and

timer off buttons.

Auto On Timer

1. Press the timer on button on the remote or press

the timer button on the control panel twice.

2. Use the up and down arrows to select the

desired amount of time before the appliance

should turn on.

3. Use the mode button to select the desired mode.

4. Use the fan button to select the desired fan

speed.

5. The time selected will appear on the display

panel and will count down until the appliance

turns on.

Auto Off Timer

1. Press the timer off button on the remote or press

the timer button on the control panel once.

2. Use the up and down arrows to select the

desired amount of time before the appliance

should turn off. The appliance will run in the

currently selected mode.

3. The time selected will appear on the display

panel and will count down until the appliance

turns off.

Using On and Off Timers Simultaneously

The on and off timers can be used at the same time.

To set the appliance to turn on, run for a set period

of time and then turn off, set the auto on timer ﬁ rst

and then set the auto off timer.

To set the appliance to run for a period of time, turn

off for a period of time and then turn back on, set

the auto off timer ﬁ rst and then set the auto on timer.

Both indicator lights will illuminate and the display

will count down to the appliance either turning off

or on, whichever function was set ﬁ rst.

The timer will not cycle the appliance on and off

indeﬁ nitely. The on and off timers will function one

time and then the appliance will return to regular

functioning.

Turning the appliance off or unplugging the

appliance will clear all memory settings, including

the timer.

CARE & MAINTENANCE

AIR FILTER

The air ﬁ lter should be cleaned approximately every

2 weeks. The air ﬁ lter may require more frequent

cleaning if there is signiﬁ cant dander or fur in the

air.

Approximately every two weeks, the ﬁ lter indicator

light on the control panel will illuminate as a

reminder to clean the ﬁ lter. Follow the steps below

to clean the ﬁ lter and return the appliance to normal

functioning.

1. The air ﬁ lter is located behind the front intake

grill. To remove the air ﬁ lter, grasp the ﬁ lter tab

on the right side of the grill and slide it out to the

right. If the front intake grill has two indents, pull

the grill forward to remove the air ﬁ lter.

2. Use a vacuum cleaner with a soft brush

attachment to remove any large debris or dust

build up from the air ﬁ lter.

3. Wash the ﬁ lter in lukewarm, soapy water, below

40°C (104°F), or use a neutral cleaning agent.

4. Rinse the ﬁ lter with clean water and dry

thoroughly before reinstalling in the appliance.

5. Press the ﬁ lter button on the control panel to

resume normal functioning.

Note: Do not operate the appliance without the air

ﬁ lter installed.

ERROR CODES

If the display panel shows any of the below error

codes, unplug the appliance, let it stand for 5-10

minutes and then plug it back in. If the error

persists, call for service.

AS - Room temperature sensor error

HS - Electric heating sensor error

. - Evaporator temperature sensor error

CLEANING

To avoid possible electric shock, ensure that the

appliance is unplugged before performing any

cleaning or maintenance.

The outside of the appliance can be wiped clean

with a soft cloth or with a lukewarm, damp cloth if

necessary.

Do not use gasoline, benzene, thinner or any

other chemicals to clean this appliance as these

substances can cause damage to the ﬁ nish and

deformation of plastic parts.

Never pour water directly onto the appliance as this

will cause deterioration of electrical components

and wiring insulation.

END OF SEASON CARE

Before removing the appliance from service for the

year, operate the appliance on high fan mode for

half a day to ensure the inside of the appliance

is dry. This will help avoid the growth of mold or

mildew inside the appliance. Ensure the ﬁ lter is

clean and dry. Store the appliance covered in a dry

location.

Note: When installing or removing the appliance

from the window, ensure that caution is taken to

prevent it from falling backward. It is recommended

that installation or removal is completed with

assistance to prevent injury to persons or damage to

property or the appliance.

DISPOSAL

Check for local regulatory compliance regarding

approved and safe disposal of this appliance.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE

Appliance will not operate • Plug is not fully inserted into the wall outlet

• Blown fuse or circuit breaker

Insufﬁ cient cooling • Air ﬁ lter is dirty

• Blocked air ﬂ ow

• Appliance size is too small for application

Noise • Inadequate support in window installation

Odors • Formation of mold or mildew on internal wet surfaces

• Place an algaecide tablet in base pan; push the tablet through

the grill on either side of the appliance

Water dripping inside • Appliance is not properly angled to allow water to drain to the

outside

Water dripping outside • On very hot or humid days dripping water from the back of the

appliance is normal

Frost build up • When outdoor temperatures are below 18.3°C (65°F) frost may

form when the appliance is in cooling mode

• Switch the appliance to fan only mode until the frost melts

Danby Consumer Care: 1-800-263-2629 or consumerservice@danby.com

Hours of operation:

Monday to Thursday 8:30 am - 6:00 pm Eastern Standard Time

Friday 8:30 am - 4:00 pm Eastern Standard Time

Information in this manual is subject to change without notice.

This Class B digital apparatus complies with the

Canadian ICES-003 standard. CAN ICES-3 (B)

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against interference in a residential installation.

This equipment generates, uses and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

interference to radio communications. However,

there is no guarantee that interference will not occur

in a particular installation.

If this equipment does cause interference to radio

or television reception, which can be determined

by turning the equipment off and on, the user is

encouraged to try to correct the interference by one

or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment

and receiver.

3. Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

4. Consult the dealer or an experienced radio/TV

technician for help.

Changes or modiﬁ cations not approved by the

party responsible for FCC compliance could void

the user’s authority to operate the equipment.

This appliance complies with Part 15 of the FCC

Rules.

Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference

received, including interference that may cause

undesired operation.

LIMITED IN-HOME APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating

conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter

“Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.

First Year

During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s

option, at no charge to the ORIGINAL purchaser.

To obtain

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance

Service

requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at

their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.

Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service

must be performed by a qualied service technician.

If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all

obligations of Danby under this warranty shall be void.

Boundaries of

If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be

In Home Service

delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for

warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he

responsibility of the purchaser.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due

to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its

authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees

under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages

to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of

the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions

(extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).

Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our

AUTHORIZED SERVICE DEPOT.

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

04/09

1-800-263-2629

Warranty Service

In-home

Transportation charges to and from the service location are not protected by this warranty and are the responsibility of the purchaser.

During the ﬁrst twenty four (24) months, any functional parts of this product found to be defective, will be repaired

or replaced, at warrantor’s option, at no charge to the original purchaser.

Contact the dealer where the unit was purchased, or contact the nearest authorized Danby service depot, where

service must be performed by a qualiﬁed service technician. If service is performed on the unit by anyone other

than an authorized service depot, all obligations of Danby under this warranty shall be void.

It is the responsibility of the purchaser to transport the appliance to the nearest authorized service depot.

First 24 months

To obtain service

LIMITED “CARRY IN” WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used

under the normal operating conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby

Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts are warranted for thirty (30) days from the date of purchase, with no extensions provided.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other

contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or implied, made

or intended by Danby or its authorized distributors and all other warranties, conditions, representations or guarantees, including any

warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation or statute is hereby expressly

excluded. Save as herein provided, Danby shall not be responsible for any damages to persons or property, including the unit itself,

howsoever caused or any consequential damages arising from the malfunction of the unit and by the purchase of the unit, the

purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or property caused by

the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating

conditions (ie. extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, ﬂoods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for outdoor

application, including but not limited to: garages, patios, porches or anywhere that is not properly insulated or climate controlled).

Proof of purchase date will be required for warranty claims; retain bills of sale. In the event that warranty service is required, present

the proof of purchase to our authorized service depot.

Warranty Service

Carry In

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

1-800-263-2629

04/17

Bienvenue

Bienvenue à la famille Danby. Nous sommes ﬁ ers de la qualité de nos produits et nous croyons

en le service ﬁ able. Nous vous suggérons de lire ce manual d’utilisation avant de brancher

votre nouvel appareil car il contient des informations inportantes sur l’utilisation, la sécurité, le

dépannage et la maintenance, aﬁ n d’assurer la ﬁ abilité et la longévité de votre appareil.

Visitez www.Danby.com pour accéder aux outils d’autoservice, aux FAQ et bien plus encore. Pour

obtenir de l’aide supplémentaire, composez 1-800-263-2629.

Notez les informations ci-dessous; Vous aurez besoin de cette information pour obtenir un

service sous garantie.

Vous devez fournir le reçu d’achat original pour valider votre garantie et recevoir le service.

Numéro de modèle: _____________________________________________

Numéro de serie: _______________________________________________

Date d’achat: __________________________________________________

Besoin d’assistance?

Avant d’appeler pour service, voici quelques choses que vous pouvez faire pour nous

aider à mieux vous servir.

Lire ce manuel du propriétaire:

Il contient des instructions pour vous aider à utiliser et à maintenir votre appareil

correctement.

Si vous recevez un appareil endommagé:

Contactez immédiatement le revendeur ou l’entrepreneur qui vous a vendu l’appareil.

Gagnez du temps et de l’argent:

Avant d’appeler pour service, consultez la section de dépannage à la ﬁ n de ce manuel.

Cette section vous aidera à résoudre les problèmes courants pouvant survenir.

1-800-26- Danby

(1-800-263-2629)

GARDEZ CES INSTRUCTIONS!

ATTENTION: RISQUE D’INCENDIE

Fluide frigorigène inﬂ ammable utilisé. Lors

de l’entretien ou de la mise au rebut du

climatiseur, le réfrigérant ne doit pas pouvoir

s’échapper à l’air libre.

INSTRUCTIONS DE MISE À LA TERRE

Cet appareil doit être mis à la terre. La mise à

la terre réduit le risque de choc électrique en

fournissant un ﬁ l d’échappement pour le courant

électrique.

Cet appareil possède un cordon doté d’un ﬁ l de

mise à la terre avec une ﬁ che à 3 broches. Le

cordon d’alimentation doit être branché sur une

prise correctement mise à la terre. Si la sortie

est une prise murale à 2 broches, elle doit être

remplacée par une prise murale à 3 broches

correctement mise à la terre. La plaque signalétique

en série indique la tension et la fréquence

auxquelles l’appareil est conçu.

AVERTISSEMENT - Une utilisation incorrecte de la

ﬁ che de mise à la terre peut entraîner un risque

d’électrocution. Consultez un électricien qualiﬁ é

ou un agent de service si les instructions de mise

à la terre ne sont pas complètement comprises ou

s’il existe un doute quant à savoir si l’appareil est

correctement mis à la terre.

Ne branchez pas votre appareil à des rallonges

ou avec un autre appareil dans la même prise

murale. Ne pas épisser le cordon d’alimentation.

Ne coupez ou retirez en aucun cas la troisième

broche du cordon d’alimentation. N’utilisez pas de

cordons de prolongement ou d’adaptateurs sans

mise à la terre (deux broches).

Si le cordon d’alimentation est endommagé, il doit

être remplacé par le fabricant, son agent de service

ou une personne qualiﬁ ée similaire aﬁ n d’éviter tout

risque.

Consignes de sécurité importantes

LIRE ET SUIVRE TOUTES LES INSTRUCTIONS DE SÉCURITÉ

EXIGENCES DE SÉCURITÉ

DANGER: Risque d’incendie ou d’explosion.

Fluide frigorigène inﬂ ammable utilisé. Ne pas

endommager le circuit de réfrigérant.

• Assurez-vous que les réparations sont effectuées

par du personnel autorisé par l’usine, aﬁ n de

minimiser les dommages au produit ou les

problèmes de sécurité.

• Consultez le manuel de réparation ou le guide

du propriétaire avant de tenter de réparer

ce produit. Toutes les précautions de sécurité

doivent être suivies.

• Éliminer correctement conformément aux

réglementations fédérales ou locales.

• Suivez attentivement les instructions de

manipulation.

• Veillez à ce que les ouvertures de ventilation de

l’appareil ne soient pas obstruées.

• N’utilisez pas d’appareils mécaniques ou

d’autres moyens pour accélérer le processus de

dégivrage.

• Les enfants doivent être surveillés pour s’assurer

qu’ils ne jouent pas avec l’appareil.

• Ne rangez pas et n’installez pas l’appareil à

proximité de sources d’allumage fonctionnant

en continu, telles que des ﬂ ammes nues ou une

cuisinière à gaz.

• Ne pas utiliser près de l’eau ou dans une pièce

humide.

• Ne pas percer ou brûler.

• Sachez que les réfrigérants peuvent ne pas

contenir d’odeur.

• L’appareil doit être rangé de manière à éviter

tout dommage mécanique.

Tout le câblage doit être conforme aux codes locaux

et nationaux et doit être installé par un électricien

qualiﬁ é. Vériﬁ ez l’alimentation disponible et

résolvez tout problème de câblage avant d’installer

et d’utiliser cet appareil.

La plaque signalétique située sur le côté droit

de l’appareil, juste au-dessus du cordon

d’alimentation, contient des données électriques et

techniques.

Cet appareil n’est pas destiné à être utilisé par des

personnes (y compris des enfants) dont les capacités

physiques, sensorielles ou mentales peuvent

être différentes ou réduites, ou qui manquent

d’expérience ou de connaissances, à moins que

ces personnes ne soient supervisées ou formées

pour faire fonctionner l’appareil par une personne

responsable de leur utilisation. sécurité.

Toute personne impliquée dans le travail sur le

circuit de ﬂ uide frigorigène doit détenir un certiﬁ cat

en cours de validité, délivré par une autorité

d’évaluation accréditée du secteur, attestant de sa

compétence pour manipuler les ﬂ uides frigorigènes

en toute sécurité, conformément à une spéciﬁ cation

d’évaluation reconnue par l’industrie.

L’entretien ne doit être effectué que selon les

recommandations du fabricant. L’entretien et les

réparations nécessitant l’assistance d’un autre

personnel qualiﬁ é doivent être effectués sous

la supervision de la personne compétente pour

l’utilisation de réfrigérants inﬂ ammables.

Lors de l’entretien ou de la mise au rebut de

l’appareil, le réfrigérant doit être récupéré

correctement et ne doit pas être autorisé à se

décharger directement dans l’air.

Informations sur le service

1. Chèques à la région: Avant de commencer

à travailler sur des systèmes contenant des

frigorigènes inﬂ ammables, des contrôles de

sécurité sont nécessaires pour réduire au

minimum le risque d’inﬂ ammation. Pour réparer

le système de réfrigération, les précautions

suivantes doivent être respectées avant de

procéder à des travaux sur le système.

2. Procédure de travail: Les travaux doivent être

effectués selon une procédure contrôlée, de

manière à minimiser le risque de présence

de gaz ou de vapeurs inﬂ ammables pendant

l’exécution des travaux.

3. Zone de travail générale: Tout le personnel de

maintenance et les autres personnes travaillant

dans la zone locale doivent être informés de la

nature des travaux effectués. Les travaux dans

des espaces conﬁ nés doivent être évités. La zone

autour de l’espace de travail doit être divisée.

Assurez-vous que les conditions dans la zone

de travail ont été sécurisées en retirant tout

matériau inﬂ ammable.

4. Vériﬁ cation de la présence de réfrigérant: Le

sont doivent être vériﬁ és avec un détecteur de

réfrigérant approprié avant et pendant le travail

pour s’assurer que le technicien est conscient

des atmosphères potentiellement inﬂ ammables.

Assurez-vous que l’équipement de détection des

fuites utilisé convient aux ﬂ uides frigorigènes

inﬂ ammables, c’est-à-dire qu’il ne produit pas

d’étincelles, est correctement scellé et de sécurité

intrinsèque.

5. Présence d’extincteur: Si des travaux à chaud

doivent être effectués sur l’équipement de

réfrigération ou sur toute pièce associée, un

équipement d’extinction d’incendie approprié

doit être disponible. Avoir un extincteur à

poudre sèche ou au C02 adjacent à la zone de

travail.

6. Aucune source d’inﬂ ammation: Aucune

personne effectuant des travaux en rapport

avec un système de réfrigération impliquant

l’exposition de tuyauteries contenant ou ayant

contenu un réfrigérant inﬂ ammable ne doit

utiliser une source d’inﬂ ammation de manière à

entraîner un risque d’incendie ou d’explosion.

Toutes les sources d’inﬂ ammation possibles, y

compris le tabagisme, doivent être sufﬁ samment

éloignées du lieu d’installation, de réparation,

de retrait et d’élimination, pendant lesquelles un

réfrigérant inﬂ ammable peut éventuellement être

rejeté dans l’espace environnant. Avant le début

des travaux, la zone autour de l’équipement

doit être inspectée pour s’assurer qu’il n’y a

pas de danger d’inﬂ ammabilité ou de risque

d’inﬂ ammation. Aucun signe de fumer ne doit

être afﬁ ché.

7. Zone ventilée: Assurez-vous que la zone

est à l’air libre ou qu’elle est correctement

ventilée avant de pénétrer dans le système ou

d’effectuer des travaux à chaud. Une certaine

ventilation doit être maintenue pendant la

durée des travaux. La ventilation doit disperser

en toute sécurité tout ﬂ uide réfrigérant libéré

et de préférence l’expulser de l’extérieur vers

l’atmosphère.

8. Contrôles à l’équipement de réfrigération:

Lorsque des composants électriques sont

remplacés, ils doivent être adaptés à l’usage

prévu et aux spéciﬁ cations appropriées.

Respectez à tout moment les directives

du fabricant en matière d’entretien et de

maintenance. En cas de doute, consultez le

service technique du fabricant.

Consignes de sécurité importantes

LIRE ET SUIVRE TOUTES LES INSTRUCTIONS DE SÉCURITÉ

La page charge ...

Danby DAC060EB7WDB Le manuel du propriétaire

Marque: Danby

Modèle: DAC060EB7WDB

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Danby DAC060EB7WDB Owner's manual
español: Danby DAC060EB7WDB El manual del propietario

Danby DAC060EB7WDB Le manuel du propriétaire

Danby DAC060EB7WDB Le manuel du propriétaire

dans d''autres langues

Documents connexes