Danby DAC080EE2WDB Le manuel du propriétaire

Marque: Danby

Modèle: DAC080EE2WDB

Taper: Le manuel du propriétaire

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE

MANUAL DEL PROPIETARIO

www.Danby.com

AIR CONDITIONER

Owner’s Manual.............................1 - 14

CLIMATISEUR

Manuel du propriétaire.................15 - 28

AIRE ACONDICIONADO

Manual del propietario.................29 - 42

MODEL * MODÈLE * MODELO

DAC080EE2WDB

2020.10.23

Welcome to the Danby family.

We are proud of our quality products and we believe in dependable service. We suggest

that you read this owner’s manual before plugging in your new appliance as it contains

important operation information, safety information, troubleshooting, and maintenance tips

to ensure the reliability and longevity of your appliance.

You are entitled to the warranty coverage as described in the owner’s manual provided with

your new appliance.

1. Please write down your appliance information below. You must keep the original proof

of purchase receipt to validate and receive warranty services.

2. Register your product online and receive a FREE 2 MONTH WARRANTY EXTENSION

after ﬁ lling out a product survey, at www.danby.com/support/product-registration/

Need Help?

1. Read your Owner’s Manual for installation help, troubleshooting, and maintenance

assistance.

2. Visit www.Danby.com to access self-service tools, FAQs and much more by searching

your model number in the search bar.

3. For the Quickest Customer Service, please ﬁ ll out the web form at www.danby.com/

support. Your submission will go directly to an expert on your particular appliance.

Our average response times are between 20 minutes and 2 hours, during EST business

hours.

4. Call 1-800-263-2629 - please note that during peak hours, hold times can exceed one

hour.

Model Number: ____________________________________________________

Serial Number: ____________________________________________________

Date of Purchase: __________________________________________________

CAUTION: RISK OF FIRE

Flammable refrigerant used. When maintaining

or disposing of the air conditioner, the refrigerant

must not be allowed to vent into the open air.

SAFETY REQUIREMENTS

DANGER: Risk of ﬁ re or explosion. Flammable

refrigerant used. Do not damage the refrigerant

circuit.

• Ensure that servicing is done by factory

authorized service personnel, to minimize

product damage or safety issues.

• Consult repair manual or owner’s guide before

attempting to service this product. All safety

precautions must be followed.

• Dispose of properly in accordance with federal

or local regulations.

• Follow handling instructions carefully.

• Keep ventilation openings, in the appliance clear

of obstruction.

• Do not use mechanical devices or other means

to accelerate the defrosting process.

• Children should be supervised to ensure that

they do not play with the appliance.

• Do not store or install the appliance near

continuously operating ignition sources such as

open ﬂ ames or a gas stove.

• Do not operate near water or in a wet room.

• Do not pierce or burn.

• Be aware that refrigerants may not contain an

odor.

• The appliance must be stored so as to prevent

mechanical damage from occurring.

All wiring must comply with local and national

codes and must be installed by a qualiﬁ ed

electrician. Check the available power supply and

resolve any wiring problems before installing and

operating this appliance.

The rating plate located on the right side of the

appliance just above the power cord contains

electrical and other technical data.

This appliance is not intended for use by persons

(including children) whose physical, sensory or

mental capabilities may be different or reduced,

or who lack experience or knowledge, unless such

persons receive supervision or training to operate

the appliance by a person responsible for their

safety.

GROUNDING INSTRUCTIONS

This appliance must be grounded. Grounding

reduces the risk of electrical shock by providing an

escape wire for the electrical current.

This appliance has a cord that has a grounding

wire with a 3-prong plug. The power cord must be

plugged into an outlet that is properly grounded.

If the outlet is a 2-prong wall outlet, it must be

replaced with a properly grounded 3-prong wall

outlet. The serial rating plate indicates the voltage

and frequency the appliance is designed for.

WARNING - Improper use of the grounding

plug can result in a risk of electric shock.

Consult a qualiﬁ ed electrician or service agent

if the grounding instructions are not completely

understood, or if doubt exists as to whether the

appliance is properly grounded.

Do not connect your appliance to extension

cords or together with another appliance in the

same wall outlet. Do not splice the power cord.

Do not under any circumstances cut or remove the

third ground prong from the power cord. Do not

use extension cords or ungrounded (two prongs)

adapters.

If the power supply cord is damaged, it must be

replaced by the manufacturer, its service agent or

similar qualiﬁ ed person in order to avoid hazard.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Any person involved with working on the refrigerant

circuit should hold a current, valid certiﬁ cate from

an industry accredited assessment authority which

authorizes their competence to handle refrigerants

safely in accordance with an industry recognized

assessment speciﬁ cation.

Servicing shall only be performed as recommended

by the manufacturer. Maintenance and repair

requiring the assistance of other skilled personnel

shall be carried out under the supervision of

the person competent in the use of ﬂ ammable

refrigerants.

When maintaining or disposing of the appliance the

refrigerant must be recovered properly and should

not be allowed to discharge to the air directly.

Information on servicing

1. Checks to the area: Prior to beginning work

on systems containing ﬂ ammable refrigerants,

safety checks are necessary to ensure that the

risk of ignition is minimized. For repair to the

refrigerating system, the following precautions

shall be complied with prior to conducting work

on the system.

2. Work procedure: Work shall be undertaken

under a controlled procedure so as to minimize

the risk of a ﬂ ammable gas or vapour being

present while the work is being performed.

3. General work area: All maintenance staff

and others working in the local area shall

be instructed on the nature of work being

carried out. Work in conﬁ ned spaces shall be

avoided. The area around the work space shall

be sectioned off. Ensure that the conditions

within the work area have been made safe by

removing all ﬂ ammable material.

4. Checking for the presence of refrigerant: The

area shall be checked with an appropriate

refrigerant detector prior to and during work

to ensure the technician is aware of potentially

ﬂ ammable atmospheres. Ensure that the leak

detection equipment being used is suitable

for use with ﬂ ammable refrigerants, i.e. non-

sparking, adequately sealed and intrinsically

safe.

5. Presence of ﬁ re extinguisher: If any hot work is

to be conducted on the refrigeration equipment

or any associated parts, appropriate ﬁ re

extinguishing equipment shall be available

to hand. Have a dry powder or C0

ﬁ re

extinguisher adjacent to the work area.

6. No ignition sources: No person carrying out

work in relation to a refrigeration system which

involves exposing any pipe work that contains

or has contained ﬂ ammable refrigerant shall use

any sources of ignition in such a manner that it

may lead to risk of ﬁ re or explosion. All possible

ignition sources including cigarette smoking,

should be kept sufﬁ ciently far away from the

site of installation, repairing, removing and

disposal during which ﬂ ammable refrigerant can

possibly be released to the surrounding space.

Prior to work taking place, the area around the

equipment is to be surveyed to make sure there

are no ﬂ ammable hazards or ignition risks. No

smoking signs shall be displayed.

7. Ventilated area: Ensure that the area is in the

open or that it is adequately ventilated before

breaking into the system or conducting any hot

work. A degree of ventilation shall continue

during the period that the work is carried out.

The ventilation should safely disperse any

released refrigerant and preferable expel it

externally into the atmosphere.

8. Checks to the refrigeration equipment: Where

electrical components are being changed, they

shall be ﬁ t for the purpose and to the correct

speciﬁ cation. At all times the manufacturer’s

maintenance and service guidelines shall be

followed. If in doubt consult the manufacturer’s

technical department for assistance.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

The following checks shall be applied to installations

using ﬂ ammable refrigerants:

• The charge size is in accordance with the room

size within which the refrigerant containing

parts are installed.

• The ventilation machinery and outlets are

operating adequately and are not obstructed.

• If an indirect refrigerating circuit is being used,

the secondary circuit shall be checked for the

presence of refrigerant.

• Marking to the equipment continues to be visible

and legible. Markings and signs that become

illegible must be corrected.

• Refrigeration pipe or components are installed in

a position where they are unlikely to be exposed

to any substance which may corrode refrigerant

containing components, unless the components

are constructed of materials which are inherently

resistant to being corroded or are suitable

protected against being corroded.

9. Checks to electrical devices: Repair and

maintenance to electrical components shall

include initial safety checks and component

inspection procedures. If a fault exists that

could compromise safety, then no electrical

supply shall be connected to the circuit until it

is satisfactorily dealt with. If the fault cannot

be corrected immediately but it is necessary to

continue operation, an adequate temporary

solution shall be used. This shall be reported to

the owner of the equipment so all parties are

advised.

Initial safety checks shall include:

• That capacitors are discharged. This shall be

done in a safe manner to avoid possibility of

sparking.

• That no live electrical components and wiring

are exposed while charging, recovering or

purging the system.

• That there is continuity of earth bonding.

Repairs to sealed components

1. During repairs to sealed components, all

electrical supplies shall be disconnected from

the equipment being worked upon prior to any

removal of sealed covers, etc. If it is absolutely

necessary to have an electrical supply to

equipment during servicing then a permanently

operating form of leak detection shall be located

at the most critical point to warn of a potentially

hazardous situation.

2. To ensure that by working on electrical

components the casing is not altered in such

a way that the level of protection is affected,

particular attention shall be paid to the

following:

• Damage to cables, excessive number of

connections, terminals not made to original

speciﬁ cation, damage to seals, incorrect ﬁ tting

of glands, etc.

• Ensure the apparatus is mounted securely.

• Ensure that seals or sealing materials have

not degraded such that they no longer serve

the purpose of preventing the ingress of

ﬂ ammable atmospheres. Replacement parts

shall be in accordance with the manufacturer’s

speciﬁ cations.

Note: The use of silicon sealant may inhibit the

effectiveness of some types of leak detection

equipment. Intrinsically safe components do not

have to be isolated prior to working on them.

Repair to intrinsically safe components

Do not apply any permanent inductive or

capacitance loads to the circuit without ensuring

that this will not exceed the permissible voltage

and current permitted for the equipment in use.

Intrinsically safe components are the only types that

can be worked on while live in the presence of a

ﬂ ammable atmosphere. The test apparatus shall

be at the correct rating. Replace components only

with parts speciﬁ ed by the manufacturer. Other

parts may result in the ignition of refrigerant in the

atmosphere from a leak.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Removal and evacuation

When breaking into the refrigerant circuit to make

repairs or for any other purpose conventional

procedures shall be used. However, it is important

that the best practice is followed since ﬂ ammability

is a consideration. The following procedures shall

be adhered to:

• Remove refrigerant.

• Purge the circuit with inert gas.

• Evacuate.

• Purge again with inert gas.

• Open the circuit by cutting or brazing.

• The refrigerant charge shall be recovered into

the correct recovery cylinders. The system shall

be ﬂ ushed with OFN to render the unit safe. This

process may need to be repeated several times.

Compressed air or oxygen shall not be used for

this task.

• Flushing shall be achieved by breaking the

vacuum in the system with OFN and continuing

to ﬁ ll until the working pressure is achieved, then

venting to atmosphere and ﬁ nally pulling down

to a vacuum. This process shall be repeated until

no refrigerant is within the system. When the

ﬁ nal OFN charge is used, the system shall be

vented down to atmospheric pressure to enable

work to take place. This operation is absolutely

vital is brazing operations on the pipe-work are

to take place.

• Ensure that the outlet for the vacuum pump is

not close to any ignition sources and there is

ventilation available.

Charging procedures

In addition to conventional charging procedures, the

following requirements shall be followed:

• Ensure that contamination of different

refrigerants does not occur when using charging

equipment. Hoses or lines shall be as short as

possible to minimize the amount of refrigerant

contained in them.

• Cylinders shall be kept upright.

• Ensure that the refrigeration system is earthed

prior to charging the system with refrigerant.

• Label the system when charging is complete, if

not already labeled.

• Extreme care shall be taken not to overﬁ ll the

refrigeration system.

• Prior to recharging the system it shall be

pressure tested with OFN. The system shall be

leak tested on completion of charging but prior

to commissioning. A follow up leak test shall be

carried out prior to leaving the site.

Cabling

Check that cabling will not be subject to wear,

corrosion, excessive pressure, vibration, sharp

edges or any other adverse environmental effects.

The check shall also take into account the effects of

aging or continual vibration from sources such as

compressors or fans.

Detection of ﬂ ammable refrigerants

Under no circumstances shall potential sources of

ignition be used in the searching for or detection

of refrigerant leaks. A halide torch or any other

detector using a naked ﬂ ame shall not be used.

Leak detection methods

The following leak detection methods are deemed

acceptable for systems containing ﬂ ammable

refrigerants:

• Electronic leak detectors shall be used to detect

ﬂ ammable refrigerants but the sensitivity may

not be adequate or may need recalibration.

Detection equipment shall be calibrated in a

refrigerant-free area. Ensure that the detector is

not a potential source of ignition and is suitable

for the refrigerant used.

• Leak detection equipment shall be set at a

percentage of the LFL of the refrigerant and

shall be calibrated to the refrigerant employed

and the appropriate percentage of gas (25%

maximum) is conﬁ rmed.

• Leak detection ﬂ uids are suitable for use with

most refrigerants but the use of detergents

containing chlorine shall be avoided as the

chlorine may react with the refrigerant and

corrode the copper or pipe-work.

• If a leak is suspected, all naked ﬂ ames shall be

removed or extinguished.

• If a leakage of refrigerant is found which

requires brazing, all of the refrigerant shall be

recovered from the system or isolated by means

of shut off valves in a part of the system remote

from the leak. Oxygen free nitrogen (OFN) shall

then be purged through the system both before

and during the brazing process.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Decommissioning

Before carrying out this procedure, it is essential

that the technician is completely familiar with the

equipment in all its detail. It is recommended good

practice that all refrigerants are recovered safely.

Prior to the task being carried out, an oil and

refrigerant sample shall be taken in case analysis is

required prior to re-use of reclaimed refrigerant. It

is essential that electrical power is available before

the task is commenced.

A. Become familiar with the equipment and its

operation.

B. Isolate system electrically.

C. Before attempting the procedure ensure that:

• Mechanical handling equipment is available

if required for handling refrigerant cylinders.

• All personal protective equipment is

available and being used correctly.

• The recovery process is supervised at all

times by a competent person.

• Recovery equipment and cylinders conform

to the appropriate standards.

D. Pump down refrigerant system, if possible.

E. If a vacuum is not possible, make a manifold so

that refrigerant can be removed from various

parts of the system.

F. Make sure that cylinder is situated on the scales

before recovery takes place.

G. Start the recovery machine and operate in

accordance with the manufacturer’s instructions.

H. Do not overﬁ ll cylinders. No more than 80%

volume liquid charge.

I. Do not exceed the maximum working pressure

of the cylinder, even temporarily.

J. When the cylinders have been ﬁ lled correctly

and the process is completed, make sure that the

cylinders and the equipment are removed from

the site promptly and all isolation valves on the

equipment are closed off.

K. Recovered refrigerant shall not be charged into

another refrigeration system unless it has been

cleaned and checked.

Labeling

Equipment shall be labeled stating that it has been

decommissioned and emptied of refrigerant. The

label shall be dated and signed. Ensure that there

are labels on the equipment stating the equipment

contains ﬂ ammable refrigerant.

Recovery

When removing refrigerant from a system, either for

servicing or decommissioning, it is recommended

good practice that all refrigerants are removed

safely.

When transferring refrigerant into cylinders, ensure

that only appropriate refrigerant recovers cylinders

are employed. Ensure that the correct number of

cylinders for holding the total system charge are

available. All cylinders to be used are designed

for the recovered refrigerant and labeled for that

refrigerant, i.e. special cylinders for the recovery

of refrigerant. Cylinders shall be complete with

pressure relief valve and associated shut-off valves

in good working order. Empty recovery cylinders

are evacuated and, if possible, cooled before

recovery occurs.

The recovery equipment shall be in good working

order with a set of instructions concerning the

equipment that is at hand and shall be suitable for

the recovery of ﬂ ammable refrigerants. In addition,

a set of calibrated weighing scales shall be

available and in good working order. Hoses shall

be complete with leak-free disconnect couplings

and in good condition. Before using the recovery

machine, check that is it in satisfactory working

order, has been properly maintained and that any

associated electrical components are sealed to

prevent ignition in the event of a refrigerant leak.

Consult the manufacturer if in doubt.

The recovered refrigerant shall be returned to the

refrigerant supplier in the correct recovery cylinder

and the relevant waste transfer note shall be

arranged. Do not mix refrigerants in recovery units

and especially not in cylinders. If compressors or

compressor oils are to be removed, ensure that they

have been evacuated to an acceptable level to make

certain that ﬂ ammable refrigerant does not remain

within the lubricant. The evacuation process shall be

carried out prior to returning the compressor to the

suppliers. Only electric heating to the compressor

body shall be employed to accelerate this process.

When oil is drained form a system, it shall be

carried out safely.

INSTALLATION INSTRUCTIONS

REQUIRED TOOLS

• Screwdrivers: Phillips and ﬂ at head.

• Power Drill: 3.2mm (1/8 inch) diameter drill bit

• Pencil

• Measuring Tape

• Scissors

• Carpenter’s Level

Note: Save the shipping carton and packing

materials for future storage or transportation.

Remove the plastic bag from the carton containing

the installation hardware kit necessary for the

installation of your air conditioner. Please check

the contents of the hardware kit against the

corresponding model check list, prior to installation

of the appliance.

INCLUDED ACCESSORIES

1. Top rail

2. Filler panels

3. Remote control

4. Battery (AAA)

5. Sash lock

6. Lock frame x2

7. 3/8” screws x4

8. 1/2” screws x3

9. 3/4” screws x4

10. Window sash seal

11. Foam top window gasket

12. Foam insulation

LOCATION

This air conditioner is designed to ﬁ t inside a

standard double-hung window between the sizes of

23” and 36”. The lower sash must allow for 14.5”

in vertical clearance.

This air conditioner is not designed for vertical,

slider type windows or “through the wall”

installation.

Ensure that the window and frame are structurally

sound and free from dry or rotted wood.

Install the air conditioner on a side of the building

which favors more shade than sunlight. If the

appliance must be in direct sunlight, it is advisable

to provide a shade awning to ensure efﬁ cient

functioning.

Do not install the appliance where leakage of

combustible gas is suspected.

This air conditioner is designed to evaporate

condensation under normal conditions. Under

extremely hot or humid conditions, excess

condensation may overﬂ ow to the outside. The air

conditioner should be installed where condensation

cannot drip on pedestrians or neighboring

properties.

Provide sufﬁ cient clearance around the appliance

to allow ample air circulation. The rear of the

appliance should be outdoors, it should not be in

a garage or another room. Keep the appliance

away from obstacles and at least 76 cm (30 inches)

above the ground. Ensure that curtains and other

obstructions do not block air ﬂ ow to the appliance.

76.2 cm

(30 inches)

50.8 cm

(20 inches)

50.8 cm

(20 inches)

12 cm

(30.5 in)

INSTALLATION INSTRUCTIONS

INSTALLATION

1. Use 4 included 3/8” screws to fasten the top

mounting rail to the air conditioner.

1/4”

2. Fasten the accordion style side panels to the

sides of the air conditioner. They are marked

“right” and “left”. Pull the leading edge to

its maximum width and then slide the panels

downward into the grooved notches on the sides

of the cabinet.

3. Place the air conditioner into the window.

Close the window securely. The upper window

should slide into the top mounting rail. The

air conditioner should be tiled by 1/4” to the

outside to allow water to drain out the back of

the cabinet.

4. Fasten the air conditioner to the window frame

using the 3 included 1/2” screws. Fasten each

of the side panels using the included 3/4”

screws and the lock frames.

5. Attach the sash lock between the top of the

sliding window and the window frame using 1

of the included 3/4” screws. To prevent outside

air from entering the room, insert the foam top

window gasket cut to the size of the window.

OPERATING INSTRUCTIONS

CONTROL PANEL

1. Fan speed: press the fan speed button to set the fan speed. In cool mode the fan can be set to high,

medium, low or auto. In fan mode the fan can be set to high, medium or low.

2. Eco mode: this mode can be used to save electricity. In eco mode, the air conditioner will turn off once

the desired temperature is reached and will not turn on again until the temperature in the room exceeds

the set temperature. While in eco mode the fan may turn on periodically for a few seconds to take an

accurate temperature reading.

3. Modes: press the mode button on the control panel to cycle and select a mode or press the desired

button on the remote.

• Auto mode: in auto mode the air conditioner automatically choose the mode of operation (cool, dry

or fan) based on ambient conditions.

• Cool mode: cool mode allows the air conditioner to cool the room and reduces air humidity. Adjust

the fan speed and air temperature to your desired comfort level. In this mode, if Eco is not enabled,

the fan may continue to run after reaching the desired temperature.

• Fan mode: used to run the fan only. Fan mode only works when the air conditioner is vented.

• Dry mode: only available by pressing the mode button on the control panel. This mode reduces the

humidity in the air. When in use, a function of alternating cooling and fan cycles is activated.

4. Filter button: after the fan motor runs for 500 total hours, the ﬁ lter check light will turn on to remind you

to clean the ﬁ lter. After cleaning the ﬁ lter, turn off the light by pressing the ﬁ lter button.

5. Sleep button: in sleep mode the air conditioner will automatically adjust the temperature and fan

speed. The set temperature will raise every 30-60 minutes and at most will change 6 times until the set

temperature is 81 or 82 degrees.

6. Timer: press the timer button to set the timer.

• Set timer on: with the air conditioner off, press the timer button and use the up and down arrows

to set the desired temperature. Press the timer button again and use the up and down arrows to

set the amount of time before the air conditioner turns on. Press the timer button again to start the

countdown.

• Set timer off: with the air conditioner on, press the timer button and use the up and down arrows to

set the amount of time before the air conditioner turns off. Press the timer button again to start the

countdown.

• The timer can be set from 0.5 - 24 hours. The up and down buttons will change the timer in 0.5

hour increments below 10 hours and in 1 hours increments above 10 hours.

7. Up and down buttons: used to set the desired temperature or the timer function.

8. Power button: used to turn the air conditioner on and off.

2 3

4 5 6

CONTROL PANEL

1. Power button: used to turn the air conditioner on and

off.

2. Cool button: press to activate cool mode.

3. Up and down buttons: used to set the desired

temperature or the timer function.

4. Sleep button: in sleep mode the air conditioner will

automatically adjust the temperature and fan speed. The

set temperature will raise every 30-60 minutes and at

most will change 6 times until the set temperature is 81

or 82 degrees.

5. Timer button: press the timer button to set the timer.

• Set timer on: with the air conditioner off, press the

timer button and use the up and down arrows to set

the desired temperature. Press the timer button again

and use the up and down arrows to set the amount

of time before the air conditioner turns on. Press the

timer button again to start the countdown.

• Set timer off: with the air conditioner on, press the

timer button and use the up and down arrows to

set the amount of time before the air conditioner

turns off. Press the timer button again to start the

countdown.

• The timer can be set from 0.5 - 24 hours. The up

and down buttons will change the timer in 0.5 hour

increments below 10 hours and in 1 hours increments

above 10 hours.

6. Auto mode button: in auto mode the air conditioner

automatically choose the mode of operation (cool, dry or

fan) based on ambient conditions.

7. Fan speed: press the fan speed button to set the fan

speed. In cool mode the fan can be set to high, medium,

low or auto. In fan mode the fan can be set to high,

medium or low.

8. Display button: press the display button to turn all lights

on the display on or off.

9. Eco mode button: this mode can be used to save

electricity. In eco mode, the air conditioner will turn off

once the desired temperature is reached and will not turn

on again until the temperature in the room exceeds the

set temperature. While in eco mode the fan may turn on

periodically for a few seconds to take an accurate.

10. Fan only button: used to run the fan only.

TEMPERATURE SCALE

1. To change the temperature scale between Fahrenheit and

Celsius, ﬁ rst turn off the unit, unplug it and wait for 2

minutes before plugging it back in.

2. Turn on the unit and set it to cool mode and medium fan

speed at a temperature of 30C (86F).

3. Press the display button on the remote control 8 times

within 8 seconds. The unit will beep and the temperature

scale will change.

OPERATING INSTRUCTIONS

CAUTION

The compressor is located on the left side of the

appliance, on the same side as the controls. This

side of the appliance will be heavier and more

awkward to manipulate. Inadequate support on

the control side of the appliance can result in

personal injury and damage to the appliance and

your property. It is recommended that you have

someone assist you during the installation of this

appliance.

CARE & MAINTENANCE

AIR FILTER

The air ﬁ lter should be cleaned approximately every

2 weeks. The air ﬁ lter may require more frequent

cleaning if there is signiﬁ cant dander or fur in the

air.

Follow the steps below to clean the ﬁ lter and return

the appliance to normal functioning. Ensure that the

program selector dial is turned to “OFF” and that

the power cord is unplugged.

1. The air ﬁ lter is located behind the front intake

grill. Pull the grill forward to remove the air ﬁ lter.

2. Use a vacuum cleaner with a soft brush

attachment to remove any large debris or dust

build up from the air ﬁ lter.

3. Wash the ﬁ lter in lukewarm, soapy water, below

40°C (104°F), or use a neutral cleaning agent.

4. Rinse the ﬁ lter with clean water and dry

thoroughly before reinstalling in the appliance.

Note: Do not operate the appliance without the air

ﬁ lter installed.

CLEANING

To avoid possible electric shock, ensure that the

appliance is unplugged before performing any

cleaning or maintenance.

The outside of the appliance can be wiped clean

with a soft cloth or with a lukewarm, damp cloth if

necessary.

Do not use gasoline, benzene, thinner or any

other chemicals to clean this appliance as these

substances can cause damage to the ﬁ nish and

deformation of plastic parts.

Never pour water directly onto the appliance as this

will cause deterioration of electrical components

and wiring insulation.

END OF SEASON CARE

Before removing the appliance from service for the

year, operate the appliance on high fan mode for

half a day to ensure the inside of the appliance

is dry. This will help avoid the growth of mold or

mildew inside the appliance. Ensure the ﬁ lter is

clean and dry. Store the appliance covered in a dry

location.

Note: When installing or removing the appliance

from the window, ensure that caution is taken to

prevent it from falling backward. It is recommended

that installation or removal is completed with

assistance to prevent injury to persons or damage to

property or the appliance.

DISPOSAL

Check for local regulatory compliance regarding

approved and safe disposal of this appliance.

Speciﬁ c electrical requirements are shown in the

diagram below. Follow the requirements below for

the type of plug on the power supply cord.

Wiring Requirements Power Supply Cord

• 115 Volt (103 min - 127

max)

• (0-8 amps)

• (10 amp time-delay fuse

or circuit breaker)

• Use on single outlet

circuit only

FREQUENTLY ASKED QUESTIONS

Can I leave my AC in place through the winter?

This is not recommended. Please bring your AC unit indoors during the winter months.

What are the standard wattage and amps used?

Information pertaining to watts and amps can be found on the rating plate located on the back of the unit.

Can I use an extension cord?

No, an extension cord may not be used.

Is there supposed to be Styrofoam in the unit?

The Styrofoam that is inside the unit acts as insulation. Do not remove it. Only remove loose packaging.

Why do I hear water in the unit?

Water is collected during the air conditioning process. This water will drain out of the unit and onto the

ground and is why the unit should be installed on a slight downward tilt.

How much does it cost to run the unit?

Please refer to the energy guide.

Odors

Odour is caused by the formation of mold or mildew on internal surfaces. This can happen when there is

poor air circulation, a dirty ﬁ lter or the air conditioner was not used for a period of time.

• Ensure the ﬁ lter is clean.

• Run the unit on fan mode to remove any internal moisture.

• Ensure that back of the unit is installed downward slope so the water can drain outside.

If the odour continues, we suggest using an algaecide tablet. Unplug the unit, then place half the tablet

through each side of the unit, through the slots on the side (usually on the portion outside of the window).

Please do not place the tablet through the front grill.

TROUBLESHOOTING

Appliance will not operate

• Plug is not fully inserted into the wall outlet

• Blown fuse or circuit breaker

Insufﬁ cient cooling

• Air ﬁ lter is dirty

• Blocked air ﬂ ow

• Appliance size is too small for application

Noise

• Inadequate support in window installation

Water dripping inside

• Appliance is not properly angled to allow water to drain to the outside

Water dripping outside

• On very hot or humid days dripping water from the back of the appliance is normal

Frost build up

• When outdoor temperatures are below 18.3°C (65°F) frost may form when the appliance is in cooling

mode

• Switch the appliance to fan only mode until the frost melts

LIMITED IN-HOME APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating

conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter

“Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.

First Year

During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s

option, at no charge to the ORIGINAL purchaser.

To obtain

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance

Service

requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at

their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.

Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service

must be performed by a qualied service technician.

If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all

obligations of Danby under this warranty shall be void.

Boundaries of

If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be

In Home Service

delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for

warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he

responsibility of the purchaser.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due

to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its

authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees

under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages

to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of

the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions

(extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).

Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our

AUTHORIZED SERVICE DEPOT.

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

04/09

1-800-263-2629

Warranty Service

In-home

Transportation charges to and from the service location are not protected by this warranty and are the responsibility of the purchaser.

During the ﬁrst twenty four (24) months, any functional parts of this product found to be defective, will be repaired

or replaced, at warrantor’s option, at no charge to the original purchaser.

Contact the dealer where the unit was purchased, or contact the nearest authorized Danby service depot, where

service must be performed by a qualiﬁed service technician. If service is performed on the unit by anyone other

than an authorized service depot, all obligations of Danby under this warranty shall be void.

It is the responsibility of the purchaser to transport the appliance to the nearest authorized service depot.

First 24 months

To obtain service

LIMITED “CARRY IN” WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used

under the normal operating conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby

Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts are warranted for thirty (30) days from the date of purchase, with no extensions provided.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other

contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or implied, made

or intended by Danby or its authorized distributors and all other warranties, conditions, representations or guarantees, including any

warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation or statute is hereby expressly

excluded. Save as herein provided, Danby shall not be responsible for any damages to persons or property, including the unit itself,

howsoever caused or any consequential damages arising from the malfunction of the unit and by the purchase of the unit, the

purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or property caused by

the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating

conditions (ie. extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, ﬂoods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for outdoor

application, including but not limited to: garages, patios, porches or anywhere that is not properly insulated or climate controlled).

Proof of purchase date will be required for warranty claims; retain bills of sale. In the event that warranty service is required, present

the proof of purchase to our authorized service depot.

Warranty Service

Carry In

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

1-800-263-2629

04/17

Bienvenue dans la famille Danby.

Nous sommes ﬁ ers de nos produits de qualité et nous croyons en un service ﬁ able. Nous

vous suggérons de lire ce manuel du propriétaire avant de brancher votre nouvel appareil

car il contient des informations de fonctionnement importantes, des informations de

sécurité, des conseils de dépannage et d’entretien pour assurer la ﬁ abilité et la longévité de

votre appareil.

Vous avez droit à la couverture de la garantie décrite dans le manuel du propriétaire fourni

avec votre nouvel appareil.

1. Veuillez noter ci-dessous les informations relatives à votre appareil. Vous devez

conserver la preuve d’achat originale pour valider et bénéﬁ cier des services de garantie.

2. Enregistrez votre produit en ligne et recevez une PROLONGATION DE GARANTIE

GRATUITE DE 2 MOIS après avoir rempli une enquête sur les produits, à l’adresse

www.danby.com/support/product-registration/

Besoin d’assistance?

1. Lisez votre manuel du propriétaire pour obtenir de l’aide à l’installation, au dépannage

et à la maintenance.

2. Visitez www.Danby.com pour accéder aux outils en libre-service, aux FAQ et bien plus

encore en recherchant votre numéro de modèle dans la barre de recherche.

3. Pour bénéﬁ cier du service client le plus rapide, veuillez remplir le formulaire Web à

l’adresse www.danby.com/support. Votre soumission ira directement à un expert de

votre appareil particulier. Nos temps de réponse moyens sont compris entre 20 minutes

et 2 heures, pendant les heures ouvrables EST.

4. Composez le 1-800-263-2629 - veuillez noter que pendant les heures de pointe, les

temps d’attente peuvent dépasser une heure.

Numéro de modèle : _______________________________________________

Numéro de serie : _________________________________________________

Date d’achat : _____________________________________________________

GARDEZ CES INSTRUCTIONS!

ATTENTION: RISQUE D’INCENDIE

Fluide frigorigène inﬂ ammable utilisé. Lors

de l’entretien ou de la mise au rebut du

climatiseur, le réfrigérant ne doit pas pouvoir

s’échapper à l’air libre.

INSTRUCTIONS DE MISE À LA TERRE

Cet appareil doit être mis à la terre. La mise à

la terre réduit le risque de choc électrique en

fournissant un ﬁ l d’échappement pour le courant

électrique.

Cet appareil possède un cordon doté d’un ﬁ l de

mise à la terre avec une ﬁ che à 3 broches. Le

cordon d’alimentation doit être branché sur une

prise correctement mise à la terre. Si la sortie

est une prise murale à 2 broches, elle doit être

remplacée par une prise murale à 3 broches

correctement mise à la terre. La plaque signalétique

en série indique la tension et la fréquence

auxquelles l’appareil est conçu.

AVERTISSEMENT - Une utilisation incorrecte de la

ﬁ che de mise à la terre peut entraîner un risque

d’électrocution. Consultez un électricien qualiﬁ é

ou un agent de service si les instructions de mise

à la terre ne sont pas complètement comprises ou

s’il existe un doute quant à savoir si l’appareil est

correctement mis à la terre.

Ne branchez pas votre appareil à des rallonges

ou avec un autre appareil dans la même prise

murale. Ne pas épisser le cordon d’alimentation.

Ne coupez ou retirez en aucun cas la troisième

broche du cordon d’alimentation. N’utilisez pas de

cordons de prolongement ou d’adaptateurs sans

mise à la terre (deux broches).

Si le cordon d’alimentation est endommagé, il doit

être remplacé par le fabricant, son agent de service

ou une personne qualiﬁ ée similaire aﬁ n d’éviter tout

risque.

Consignes de sécurité importantes

LIRE ET SUIVRE TOUTES LES INSTRUCTIONS DE SÉCURITÉ

EXIGENCES DE SÉCURITÉ

DANGER: Risque d’incendie ou d’explosion.

Fluide frigorigène inﬂ ammable utilisé. Ne pas

endommager le circuit de réfrigérant.

• Assurez-vous que les réparations sont effectuées

par du personnel autorisé par l’usine, aﬁ n de

minimiser les dommages au produit ou les

problèmes de sécurité.

• Consultez le manuel de réparation ou le guide

du propriétaire avant de tenter de réparer

ce produit. Toutes les précautions de sécurité

doivent être suivies.

• Éliminer correctement conformément aux

réglementations fédérales ou locales.

• Suivez attentivement les instructions de

manipulation.

• Veillez à ce que les ouvertures de ventilation de

l’appareil ne soient pas obstruées.

• N’utilisez pas d’appareils mécaniques ou

d’autres moyens pour accélérer le processus de

dégivrage.

• Les enfants doivent être surveillés pour s’assurer

qu’ils ne jouent pas avec l’appareil.

• Ne rangez pas et n’installez pas l’appareil à

proximité de sources d’allumage fonctionnant

en continu, telles que des ﬂ ammes nues ou une

cuisinière à gaz.

• Ne pas utiliser près de l’eau ou dans une pièce

humide.

• Ne pas percer ou brûler.

• Sachez que les réfrigérants peuvent ne pas

contenir d’odeur.

• L’appareil doit être rangé de manière à éviter

tout dommage mécanique.

Tout le câblage doit être conforme aux codes locaux

et nationaux et doit être installé par un électricien

qualiﬁ é. Vériﬁ ez l’alimentation disponible et

résolvez tout problème de câblage avant d’installer

et d’utiliser cet appareil.

La plaque signalétique située sur le côté droit

de l’appareil, juste au-dessus du cordon

d’alimentation, contient des données électriques et

techniques.

Cet appareil n’est pas destiné à être utilisé par des

personnes (y compris des enfants) dont les capacités

physiques, sensorielles ou mentales peuvent

être différentes ou réduites, ou qui manquent

d’expérience ou de connaissances, à moins que

ces personnes ne soient supervisées ou formées

pour faire fonctionner l’appareil par une personne

responsable de leur utilisation. sécurité.

Toute personne impliquée dans le travail sur le

circuit de ﬂ uide frigorigène doit détenir un certiﬁ cat

en cours de validité, délivré par une autorité

d’évaluation accréditée du secteur, attestant de sa

compétence pour manipuler les ﬂ uides frigorigènes

en toute sécurité, conformément à une spéciﬁ cation

d’évaluation reconnue par l’industrie.

L’entretien ne doit être effectué que selon les

recommandations du fabricant. L’entretien et les

réparations nécessitant l’assistance d’un autre

personnel qualiﬁ é doivent être effectués sous

la supervision de la personne compétente pour

l’utilisation de réfrigérants inﬂ ammables.

Lors de l’entretien ou de la mise au rebut de

l’appareil, le réfrigérant doit être récupéré

correctement et ne doit pas être autorisé à se

décharger directement dans l’air.

Informations sur le service

1. Chèques à la région: Avant de commencer

à travailler sur des systèmes contenant des

frigorigènes inﬂ ammables, des contrôles de

sécurité sont nécessaires pour réduire au

minimum le risque d’inﬂ ammation. Pour réparer

le système de réfrigération, les précautions

suivantes doivent être respectées avant de

procéder à des travaux sur le système.

2. Procédure de travail: Les travaux doivent être

effectués selon une procédure contrôlée, de

manière à minimiser le risque de présence

de gaz ou de vapeurs inﬂ ammables pendant

l’exécution des travaux.

3. Zone de travail générale: Tout le personnel de

maintenance et les autres personnes travaillant

dans la zone locale doivent être informés de la

nature des travaux effectués. Les travaux dans

des espaces conﬁ nés doivent être évités. La zone

autour de l’espace de travail doit être divisée.

Assurez-vous que les conditions dans la zone

de travail ont été sécurisées en retirant tout

matériau inﬂ ammable.

4. Vériﬁ cation de la présence de réfrigérant: La

zone sont doivent être vériﬁ és avec un détecteur

de réfrigérant approprié avant et pendant

le travail pour s’assurer que le technicien est

conscient des atmosphères potentiellement

inﬂ ammables. Assurez-vous que l’équipement

de détection des fuites utilisé convient aux ﬂ uides

frigorigènes inﬂ ammables, c’est-à-dire qu’il ne

produit pas d’étincelles, est correctement scellé

et de sécurité intrinsèque.

5. Présence d’extincteur: Si des travaux à chaud

doivent être effectués sur l’équipement de

réfrigération ou sur toute pièce associée, un

équipement d’extinction d’incendie approprié

doit être disponible. Avoir un extincteur à

poudre sèche ou au C02 adjacent à la zone de

travail.

6. Aucune source d’inﬂ ammation: Aucune

personne effectuant des travaux en rapport

avec un système de réfrigération impliquant

l’exposition de tuyauteries contenant ou ayant

contenu un réfrigérant inﬂ ammable ne doit

utiliser une source d’inﬂ ammation de manière à

entraîner un risque d’incendie ou d’explosion.

Toutes les sources d’inﬂ ammation possibles, y

compris le tabagisme, doivent être sufﬁ samment

éloignées du lieu d’installation, de réparation,

de retrait et d’élimination, pendant lesquelles un

réfrigérant inﬂ ammable peut éventuellement être

rejeté dans l’espace environnant. Avant le début

des travaux, la zone autour de l’équipement

doit être inspectée pour s’assurer qu’il n’y a

pas de danger d’inﬂ ammabilité ou de risque

d’inﬂ ammation. Aucun signe de fumer ne doit

être afﬁ ché.

7. Zone ventilée: Assurez-vous que la zone

est à l’air libre ou qu’elle est correctement

ventilée avant de pénétrer dans le système ou

d’effectuer des travaux à chaud. Une certaine

ventilation doit être maintenue pendant la

durée des travaux. La ventilation doit disperser

en toute sécurité tout ﬂ uide réfrigérant libéré

et de préférence l’expulser de l’extérieur vers

l’atmosphère.

8. Contrôles à l’équipement de réfrigération:

Lorsque des composants électriques sont

remplacés, ils doivent être adaptés à l’usage

prévu et aux spéciﬁ cations appropriées.

Respectez à tout moment les directives

du fabricant en matière d’entretien et de

maintenance. En cas de doute, consultez le

service technique du fabricant.

Consignes de sécurité importantes

LIRE ET SUIVRE TOUTES LES INSTRUCTIONS DE SÉCURITÉ

Les contrôles suivants doivent être appliqués aux

installations utilisant des réfrigérants inﬂ ammables:

• La taille de la charge est conforme à la taille de

la pièce dans laquelle les pièces contenant le

réfrigérant sont installées.

• Les machines de ventilation et les sorties

fonctionnent de manière adéquate et ne sont pas

obstruées.

• Si un circuit de réfrigération indirect est utilisé,

le circuit secondaire doit être vériﬁ é pour la

présence de réfrigérant.

• Le marquage sur l’équipement continue d’être

visible et lisible. Les marques et les signes qui

deviennent illisibles doivent être corrigés.

• Les tuyaux ou composants de réfrigération sont

installés dans une position où ils ne risquent

pas d’être exposés à une substance susceptible

de corroder les composants contenant du

réfrigérant, à moins que les composants

ne soient construits avec des matériaux

intrinsèquement résistants à la corrosion ou

protégés de manière adéquate.

9. Contrôles aux appareils électriques: La

réparation et la maintenance des composants

électriques doivent inclure les contrôles de

sécurité initiaux et les procédures d’inspection

des composants. S’il existe un défaut

susceptible de compromettre la sécurité, aucune

alimentation électrique ne doit être connectée

au circuit jusqu’à ce que le problème soit

résolu. Si le défaut ne peut pas être corrigé

immédiatement mais qu’il est nécessaire de

poursuivre le fonctionnement, une solution

temporaire adéquate doit être utilisée. Cela doit

être signalé au propriétaire de l’équipement aﬁ n

que toutes les parties soient informées.

Les contrôles de sécurité initiaux doivent inclure:

• Que les condensateurs sont déchargés. Ceci

doit être fait de manière sûre pour éviter la

possibilité d’étincelles.

• Qu’aucun composant ni câblage électrique sous

tension ne soit exposé pendant le chargement, la

récupération ou la purge du système.

• Qu’il existe une continuité de la mise à la terre.

Réparation de composants scellés

1. Lors de la réparation de composants scellés,

toutes les alimentations électriques doivent

être débranchées de l’équipement utilisé

avant toute dépose de couvercles scellés,

etc. S’il est absolument nécessaire de prévoir

une alimentation électrique de l’équipement

pendant l’entretien, une détection des fuites

fonctionnant en permanence doit être situé au

point le plus critique pour avertir d’une situation

potentiellement dangereuse.

2. Aﬁ n de garantir qu’en manipulant des

composants électriques, le boîtier ne soit pas

modiﬁ é de telle sorte que le niveau de protection

soit affecté, une attention particulière doit être

accordée aux éléments suivants:

• Dommages aux câbles, nombre excessif

de connexions, bornes non conformes aux

spéciﬁ cations d’origine, dommages aux joints,

mauvais montage des presse-étoupes, etc.

• Assurez-vous que l’appareil est bien monté.

• Assurez-vous que les joints ou les matériaux

d’étanchéité ne se sont pas dégradés de telle

sorte qu’ils ne servent plus à empêcher la

pénétration d’atmosphères inﬂ ammables. Les

pièces de rechange doivent être conformes aux

spéciﬁ cations du fabricant.

Remarque: l’utilisation d’un produit d’étanchéité à

base de silicone peut nuire à l’efﬁ cacité de certains

types d’équipement de détection de fuites. Les

composants de sécurité intrinsèque ne doivent pas

nécessairement être isolés avant de travailler dessus.

Réparation de composants à sécurité intrinsèque

N’appliquez aucune charge inductive ou capacitive

permanente sur le circuit sans vous assurer que cela

ne dépassera pas la tension et le courant autorisés

pour l’équipement utilisé. Les composants à sécurité

intrinsèque sont les seuls types sur lesquels on

peut travailler tout en vivant dans une atmosphère

inﬂ ammable. L’appareil d’essai doit avoir la cote

correcte. Remplacez les composants uniquement

par des pièces spéciﬁ ées par le fabricant. D’autres

pièces peuvent provoquer l’inﬂ ammation de

réfrigérant dans l’atmosphère par une fuite.

Consignes de sécurité importantes

LIRE ET SUIVRE TOUTES LES INSTRUCTIONS DE SÉCURITÉ

Consignes de sécurité importantes

LIRE ET SUIVRE TOUTES LES INSTRUCTIONS DE SÉCURITÉ

Enlèvement et évacuation

Lorsque vous pénétrez dans le circuit de ﬂ uide

frigorigène pour effectuer des réparations ou à

toute autre ﬁ n, vous devez utiliser des procédures

classiques. Cependant, il est important que la

meilleure pratique soit suivie car l’inﬂ ammabilité est

une considération. Les procédures suivantes doivent

être respectées:

• Retirer le réfrigérant.

• Purger le circuit avec du gaz inerte.

• Évacuer.

• Purger à nouveau avec un gaz inerte.

• Ouvrir le circuit en coupant ou en soudant.

• La charge de réfrigérant doit être récupérée

dans les bonnes bouteilles de récupération.

Le système doit être rincé avec OFN pour

sécuriser l’unité. Ce processus peut avoir besoin

d’être répété plusieurs fois. L’air comprimé ou

l’oxygène ne doit pas être utilisé pour cette

tâche.

• Le rinçage doit être réalisé en rompant le vide

dans le système avec OFN et en continuant à se

remplir jusqu’à atteindre la pression de travail,

puis en relâchant dans l’atmosphère et en tirant

ﬁ nalement vers le vide. Ce processus doit être

répété jusqu’à ce qu’il n’y ait plus de réfrigérant

dans le système. Lorsque la dernière charge

OFN est utilisée, le système doit être purgé

à la pression atmosphérique pour permettre

le travail. Cette opération est absolument

essentielle si des opérations de brasage sur la

tuyauterie doivent avoir lieu.

• Assurez-vous que la sortie de la pompe à

vide ne se trouve pas à proximité de sources

d’inﬂ ammation et qu’il existe une ventilation.

Procédures de charge

Outre les procédures de chargement classiques, les

exigences suivantes doivent être respectées:

• Assurez-vous que les différents réfrigérants

ne soient pas contaminés lors de l’utilisation

d’un équipement de charge. Les tuyaux ou les

conduites doivent être aussi courts que possible

pour minimiser la quantité de réfrigérant qu’ils

contiennent.

• Les bouteilles doivent être maintenues debout.

• Assurez-vous que le système de réfrigération

est mis à la terre avant de le charger avec du

réfrigérant.

• Étiquetez le système lorsque le chargement est

terminé, s’il ne l’est pas déjà.

• Un soin extrême doit être pris pour ne pas trop

remplir le système de réfrigération.

• Avant de recharger le système, il doit être

testé sous pression avec OFN. Le système doit

être soumis à un test d’étanchéité à la ﬁ n du

chargement mais avant la mise en service. Un

contrôle d’étanchéité doit être effectué avant de

quitter le site.

Le câblage

Vériﬁ ez que le câblage ne sera pas soumis à

l’usure, à la corrosion, à une pression excessive,

aux vibrations, aux arêtes vives ou à tout autre

effet néfaste sur l’environnement. La vériﬁ cation

doit également prendre en compte les effets

du vieillissement ou des vibrations continuelles

provenant de sources telles que les compresseurs ou

les ventilateurs.

Détection de réfrigérants inﬂ ammables

En aucun cas, des sources d’inﬂ ammation

potentielles ne doivent être utilisées pour rechercher

ou détecter des fuites de réfrigérant. Une lampe à

incandescence ou tout autre détecteur utilisant une

ﬂ amme nue ne doit pas être utilisé.

Méthodes de détection de fuite

Les méthodes de détection des fuites suivantes sont

jugées acceptables pour les systèmes contenant des

réfrigérants inﬂ ammables:

• Des détecteurs de fuites électroniques doivent

être utilisés pour détecter les réfrigérants

inﬂ ammables, mais la sensibilité peut ne pas

être adéquate ou nécessiter un réétalonnage.

L’équipement de détection doit être étalonné

dans une zone sans réfrigérant. Assurez-vous

que le détecteur n’est pas une source potentielle

d’inﬂ ammation et qu’il convient au réfrigérant

utilisé.

• L’équipement de détection de fuites doit être

réglé sur un pourcentage de la LF du réfrigérant

et doit être calibré avec le réfrigérant utilisé et le

pourcentage de gaz approprié (25% maximum)

est conﬁ rmé.

• Les ﬂ uides de détection des fuites peuvent

être utilisés avec la plupart des réfrigérants,

mais l’utilisation de détergents contenant du

chlore doit être évitée car le chlore peut réagir

avec le réfrigérant et corroder le cuivre ou les

tuyauteries.

• Si une fuite est suspectée, toutes les ﬂ ammes

nues doivent être supprimées ou éteintes.

• Si une fuite de réfrigérant nécessitant un

brasage est détectée, tout le réfrigérant doit

être récupéré du système ou isolé au moyen

de vannes d’arrêt dans une partie du système

éloignée de la fuite. L’azote libre d’oxygène

(OFN) doit ensuite être purgé à travers le

système avant et pendant le processus de

brasage.

La page charge ...

Danby DAC080EE2WDB Le manuel du propriétaire

Marque: Danby

Modèle: DAC080EE2WDB

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Danby DAC080EE2WDB Owner's manual
español: Danby DAC080EE2WDB El manual del propietario

Danby DAC080EE2WDB Le manuel du propriétaire

Danby DAC080EE2WDB Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents