HellermannTyton Autotool System 3080 Assembly Instructions Manual
- Catégorie
- Kits de voiture
- Taper
- Assembly Instructions Manual
Autotool System 3080
Assembly Instructions
Montageanleitung
Bench mount kit horizontal 3080
2
GB
English
DE
Deutsch
Translation of the original instructions 3
Originalanleitung 21
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
3
Assembly Instructions
Translation of the original instructions
Table of contents
1 Notes for the user ................... 2
1.1 Information about these instructions ... 2
1.2 Information about the product ........ 2
1.3 Warranty ........................ 2
1.4 Contact data ..................... 2
1.5 Copyright and intellectual property rights 2
1.6 Keeping and dissemination of these
instructions. . . . . . . . . . . . . . . . . . . . . . . 2
1.7 Target group of these instructions ...... 2
1.8 General information ................ 2
1.9 Conventions adopted in these instructions 2
1.9.1 Classification of the precautionary notices 2
1.9.2 Other notational conventions ......... 2
2 Safety warnings .................... 3
2.1 General power tool safety warnings .... 3
2.2 Intended use ..................... 3
2.3 Misuse .......................... 3
2.4 Personnel qualification .............. 3
2.4.1 Specialist personnel for operation ...... 3
2.4.2 Specialist personnel for maintenance and
repair ........................... 3
2.4.3 Authorised person for low-voltage
electrical equipment ................ 3
2.4.4 Authorised specialist for repair and testing 3
2.5 Underlying hazards associated with use of
the ATS3080 or the Bench mount kit
horizontal 3080 ................... 3
2.5.1 Electricity and compressed air ......... 3
2.5.2 Cleanliness at the workplace .......... 3
2.5.3 Spare parts and accessories .......... 4
3 Functional description ................ 4
3.1 ATS3080 ........................ 4
3.2 Power pack 3080 .................. 4
3.3 Bench mount kit horizontal 3080 ...... 5
4 Transport, scope of supply and storage .. 5
4.1 Transporting the device ............. 5
4.2 Scope of supply ................... 5
4.3 Disposal ......................... 5
4.4 Storage ......................... 6
4.4.1 ATS3080 and Power pack 3080 ....... 6
4.4.2 Strap and closures ................. 6
5 Installation ........................ 6
5.1 Installing Bench mount kit
horizontal 3080 ................... 6
5.1.1 Setting up Bench mount kit
horizontal 3080 ................... 6
5.1.2 ATS3080 insertion ................. 7
5.1.3 Adjusting the point-to-point path ...... 7
5.1.4 Connecting the ATS3080 and Bench mount
kit horizontal 3080 ................. 7
5.1.5 Inserting the BMK closure chain guide .. 8
5.1.6 Inserting the closure reel ............. 8
5.1.7 Inserting the strap reel .............. 9
5.2 Positioning ...................... 10
5.2.1 Positioning the material for bundling .. 10
5.2.2 Geometries of materials for bundling .. 10
5.3 Check of finished bindings .......... 10
5.4 Sequence of movements in normal
operation ....................... 10
5.4.1 Point-to-point path ................ 11
6 Control unit ....................... 11
6.1 Precondition ..................... 11
6.2 Error messages ................... 11
6.3 Rectifying error ................... 11
7 Maintenance ...................... 11
7.1 Important notes .................. 11
7.2 Spare parts ...................... 11
7.3 General maintenance activities ....... 11
7.4 Changing the strap reel ............ 12
7.5 Changing the closure reel ........... 12
8 Technical data ..................... 13
8.1 Interface overview, Power pack 3080 .. 13
8.2 Bench mount kit horizontal 3080 ..... 14
8.3 Control boxes .................... 15
8.3.1 Interface overview, control boxes ..... 15
8.3.2 Connector pinouts, control boxes ..... 15
8.4 Connection plan .................. 16
8.5 Circuit diagram ................... 17
9 Declaration of conformity ............ 18
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Notes for the user
4
1 Notes for the user
These instructions will help you use the Bench mount kit
horizontal 3080. They contain important information
and safety instructions that will enable you to install the
Bench mount kit horizontal 3080 properly and utilise it
correctly and economically for its intended use.
1.1 Information about these instructions
Use these instructions only together with the Operating
Instructions of the ATS3080.
Last update: 23.01.2018
1.2 Information about the product
Product designation: Bench mount kit horizontal 3080
Article number: 102-00041
1.3 Warranty
The warranty is in accordance with statutory
requirements. Warranty entitlement applies only in the
country in which the device was originally purchased.
Batteries, fuses and light sources are not covered by the
warranty.
1.4 Contact data
The manufacturer of the product described in these
instructions is:
HellermannTyton GmbH
Grosser Moorweg 45
D-25436 Tornesch, Germany
Tel. +49 4122 701-0
www.HellermannTyton.de
info@HellermannTyton.de
1.5 Copyright and intellectual property rights
The manufacturer retains the copyright to these
instructions. Under no circumstances may these
instructions be reproduced or electronically processed,
replicated or disseminated, in whole or in part, without
the prior written consent of HellermannTyton GmbH
(hereinafter referred to as HellermannTyton).
Any breach or infringement of these stipulations will
result in liability for damages.
1.6 Keeping and dissemination of these instructions
These instructions must be kept in the immediate vicinity
of the workplace and must be available at all times to all
operating personnel. The operating company shall
inform the operating personnel of the location of these
instructions. The operating company shall obtain
replacement from the manufacturer if these instructions
are no longer easily legible.
If the product is acquired by or sold on to a third party
the following documents must be handed over to the
new owner:
• These instructions
• Documents relating to repair work
• Logs of repair work undertaken
1.7 Target group of these instructions
These instructions must be read and complied with by
every person charged with any of the following tasks:
• Installation
• Operation
• Maintenance
• Repair
• Fault rectification
1.8 General information
All accompanying drawings are exempt from the
modification service.
1.9 Conventions adopted in these instructions
1.9.1 Classification of the precautionary notices
Precautionary notices in these instructions draw
attention to hazards associated with use of the device
and indicate how they can be avoided.
Non-compliance of any nature whatsoever can lead to
accidents with fatal consequences, injury or damage to
property.
The precautionary notices are subdivided into three
groups according to the severity of the potential hazard:
DANGER
Texts accompanied by the signal word "DANGER" indicate
hazardous situations which, in the event of non-compliance
with the appropriate precautions, will cause death or severe
injury.
WARNING
Texts accompanied by the signal word "WARNING" indicate
hazardous situations which, in the event of non-compliance
with the appropriate precautions, can cause serious injury.
CAUTION
Texts accompanied by the signal word "CAUTION" indicate
hazardous situations which, in the event of non-compliance
with the appropriate precautions, can cause slight injury.
1.9.2 Other notational conventions
f Indicates an instruction
• Indicates an item in a bulleted list
; Indicates the result of an action
à This text highlight is used for cross-references.
NOTE
Texts accompanied by the signal word "NOTE" indicate
situations which, in the event of non-compliance with the
appropriate precautions, can cause damage to the ATS3080
or the Bench mount kit horizontal 3080.
Texts accompanied by this symbol contain information about
environmental protection.
Texts accompanied by this symbol contain useful additional
information.
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Safety warnings
5
2 Safety warnings
2.1 General power tool safety warnings
The safety warnings in the Operating instructions for the
ATS3080 also apply to operation of the ATS3080 after
installation of an automation system or device.
WARNING
Non-compliance with the safety warnings below can
lead to severe injuries, fire and electric shock.
f Comply with the instructions and warnings below.
f Keep the Operating instructions for the ATS3080 ready
to hand.
2.2 Intended use
Use the Bench mount kit horizontal 3080 only when it is
in full working order and safe, always be safety-
conscious and aware of the hazards.
The Bench mount kit horizontal 3080 with integrated
ATS3080 is suitable for and intended for the following
uses:
• Automatic binding of bundles up to a diameter of max.
80 mm
• For indoor use only
• Industrial use
• When incorporated into automated production lines, the
Bench mount kit horizontal 3080 must be installed
horizontally; use is permitted only when it is installed in
this position.
2.3 Misuse
Use other than that stated in the section entitled
"Intended use" is misuse. The operating company
responsible for use of the Bench mount kit
horizontal 3080 bears sole responsibility for injury and
damage resulting from misuse.
The safety regulations for the ATS3080 (see the
Operating Instructions for the ATS3080) apply in
addition.
The following are specifically prohibited:
• Use with faulty parts
• Use in explosive environments or in the presence of a fire
hazard
• Use outdoors
• Use in high humidity and/or direct sunlight
• Manipulation while processes are in progress
• Unauthorised alterations and modifications to the Bench
mount kit horizontal 3080 and its component parts
without the prior consent of HellermannTyton
• Use of spare parts and accessories not tested and
approved beforehand by HellermannTyton
2.4 Personnel qualification
Underage persons and trainees are permitted to use the
device only under the supervision of an experienced
specialist and only with the express permission of the
operating company.
2.4.1 Specialist personnel for operation
The tasks and authorisations assigned to specialist
personnel for extended operation are as follows:
• Operation of the ATS3080 and the Bench mount kit
horizontal 3080
• Rectification of faults or, as applicable, initiation of
measures for the rectification of faults
• Cleaning of the ATS3080 and the Bench mount kit
horizontal 3080
These individuals have the specialist training or practical
experience that will ensure correct handling.
2.4.2 Specialist personnel for maintenance and repair
Always have maintenance and repair work carried out by
duly qualified specialist personnel. These individuals have
received training that affords sucient knowledge of the
ATS3080 or the Bench mount kit horizontal 3080 for
them to judge when it is in safe working order.
These individuals are also familiar with the following
rules and regulations:
• Applicable national health and safety regulations
• Accident prevention regulations
• Generally accepted codes of practice, regulations and
standards
2.4.3 Authorised person for low-voltage electrical
equipment
Work on the electrical supply and on parts that are live
when the device is in operation should always be carried
out by a person duly authorised to work on low-voltage
electrical equipment.
2.4.4 Authorised specialist for repair and testing
Only service technicians from HellermannTyton or service
technicians authorised by HellermannTyton are permitted
to carry out repairs and safety checks.
2.5 Underlying hazards associated with use of the
ATS3080 or the Bench mount kit
horizontal 3080
2.5.1 Electricity and compressed air
f Always wear safety glasses and suitable safety
equipment whilst working.
f Before installation, cleaning and maintenance,
depressurise disconnect the ATS3080, the Power
pack3080 and the Bench mount kit horizontal 3080
from the power supply.
2.5.2 Cleanliness at the workplace
Orderliness, good lighting and cleanliness at the
workplace all help to make work easier and to minimise
hazards and the risk of injury.
Always comply with the following principles of
orderliness and cleanliness at the workplace:
f Put tools away as soon as they are no longer needed.
f Avoid trips (e.g. immediately dispose of waste by placing
it in the containers provided for the purpose).
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Functional description
6
f Immediately remove spillages of grease, oil and other
liquids.
f Avoid dirt on the display field of the ATS3080.
2.5.3 Spare parts and accessories
• Use only original replacement parts.
• After parts have been replaced, always make sure that
everything is in full working order.
• Use only accessories approved by HellermannTyton.
Accessories can affect the way in which the ATS3080 or
Bench mount kit horizontal 3080 works.
3 Functional description
ATS3080 and Power pack 3080 are not included in the scope
of supply. For a description of the ATS3080 and the Power
pack 3080, see the Operating Instructions for the ATS3080.
3.1 ATS3080
567
1
3
4
2
8
1 ATS3080
2 Reset lever
3 Display
4 Grip
5 Triggering lever
6 Front cap with sensor
7 Upper and lower jaws
8 Jaw-opening lever
The ATS3080 1 loops the inserted strap round the
bundle, tensions and then cuts off the strap. Binding is a
zero-waste operation.
3.2 Power pack 3080
Power
Signal
1
4
3
2
5
6
1 Housing
2 Power cable (socket and fuse on the rear of the housing)
3 Socket for connection to ATS3080
4 LED indicator, operating voltage
5 LED indicator on Power pack 3080switched on
6 Main switch
The Power pack 3080 supplies electricity to the
ATS3080.
To the interfaces on both sides of the housing,
à"Interface overview, Power pack 3080" on
page15.
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Transport, scope of supply and storage
7
3.3 Bench mount kit horizontal 3080
11
10
9
2
5
6
7
8
3
4
1
12
1 Brake block
2 Holder for strap reel
3 Deflection roller
4 Column
5 Control boxes
6 Compressed air filter
7 Mounting angle bracket
8 Tool holder
9 ATS3080
10 Reset button
11 BMK closure chain guide
12 Holder for closure reel
The Bench mount kit horizontal 3080 enables the
ATS3080 to be held in a horizontal position, turned
sideways. The Bench mount kit horizontal 3080 is bolted
to the base by mounting angle bracket 7 .
This bundling is carried out vertically by the ATS3080 9 .
An automatic binding is triggered by the control unit
à"Control unit" on page13.
4 Transport, scope of supply and storage
4.1 Transporting the device
Always use the supplied box to transport the Bench
mount kit horizontal 3080.
The components of the Bench mount kit horizontal 3080
are packaged for transport.
NOTE
Components not correctly packed are subject to a risk of
damage in transit.
f Do not unpack components until just before they are
going to be installed.
4.2 Scope of supply
Name Article number
Assembly Instructions 102-01011
Power pack 3080 24 V 102-00142
Push button switch 123-90055
Deflection roller (x3) 102-73026
Spring for deflection roller 102-74006
Foot pedal cable 2m [X1]* 123-90061
Plug connector for PLC, with cable 2m [X2]* 102-00214
Plug connector for PLC, with cable 2m [X3]* 102-00215
Limiting block 30/50 102-10063
Limiting block 80 102-10064
BMK 3080 closure chain guide 102-00325
*) X1 … X3: à"Connection plan" on page18
4.3 Disposal
The operating company is under obligation to ensure
that at the end of its useful life, the ATS3080 and the
components including the accessories are disposed of in
accordance with the applicable local regulations. End-of-
life (EOL) disposal of the ATS3080 and individual
subassemblies and the disposal of consumables and
auxiliaries are subject in part to statutory regulations.
The appropriate local authorities will provide detailed
information on request.
f Always dispose of packaging materials in accordance
with the currently valid materials-disposal and
environmental protection regulations.
f Always take materials, production waste and
consumables for disposal to certified collection points.
f Contact the manufacturer for advice if there is any lack
of clarity regarding disposal.
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Installation
8
4.4 Storage
4.4.1 ATS3080 and Power pack 3080
f ATS3080 and Power pack 3080 in a cool, dry place.
f Avoid direct sunlight.
f ATS3080 and store Power pack 3080 in dustproof
packaging.
f Store electrical components (ATS3080 and Power
pack3080) in impact-absorbing packaging and
separately from the accessories.
f Consult and comply with the appropriate data sheets for
storage of the accessories.
4.4.2 Strap and closures
NOTE
Strap and closures are not resistant to ageing. The plastic
deteriorates if storage time is prolonged.
f Use up the strap and closures promptly.
Storage temperature 20 °C – 23 °C
Relative humidity 50% rel.
f Always store the strap reels and the closure reels until
needed in the bags in which they are supplied and make
sure that the bags remain airtight. If necessary, seal the
bags with adhesive tape.
f Do note keep in storage for longer than 6 months.
f Never leave the packaging open for longer than
12hours.
f Do not open the packaging until immediately before the
contents are to be used and use up the whole strap
promptly.
f Do not expose the strap reels or the closure reels to
direct sunlight.
f Keep the strap reels and the closure reels away from
sources of heat.
5 Installation
5.1 Installing Bench mount kit horizontal 3080
Tools needed
• Open-ended spanner, w/f 10 mm
• Allen key, w/f 5 mm
CAUTION
Crush hazard when jaws close
f Always keep the Power pack 3080 pack switched off
while installation is in progress.
f Depressurise the compressed-air system and secure it
against unintentional restart.
5.1.1 Setting up Bench mount kit horizontal 3080
4
3
1
2
f Position the base 2 of Bench mount kit
horizontal 3080 1 on a clean, level and flat worktop.
f Secure the Bench mount kit horizontal 3080 1 to the
worktop with three mounting angle brackets 3 so that it
cannot slip out of position.
Recommended screw size: M6 x 25 mm (min.)
f Connect a grounding cable (min. 16 mm
2
) to stud 4 of
the Bench mount kit horizontal 3080 1 .
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Installation
9
5.1.2 ATS3080 insertion
1
f Remove the size 80 quadrant stop from the right side of
the ATS3080 and break off tab 1 .
f Re-insert the quadrant stop without the tab.
2
3
5
4
6
f Unscrew knurled screws 3 holding cover 2 of tool
holder 6 and remove cover 2 .
f Insert the ATS3080 4 with the grip into the tool
holder 6 .
; Sensor 5 slots into the opening on the right side of the
tool.
f Hold cover 2 of tool holder 6 in position and secure it
with knurled screws 3 to the ATS3080 4 .
5.1.3 Adjusting the point-to-point path
The point-to-point path has to be adjusted to suit the
jaw size of the ATS3080, à"Sequence of movements in
normal operation" on page12.
1
2
f Unscrew screw 1 of limiting block 2 , and move limiting
block 2 to the desired position.
• The point-to-point path for jaws with Ø30 mm and Ø50
mm is 15 mm.
• The point-to-point path for jaws with Ø80 mm is
22mm.
f Secure limiting block 2 with screw 1 .
5.1.4 Connecting the ATS3080 and Bench mount kit
horizontal 3080
Power
Signal
2
1
3
4
5
To connect the ATS3080 and the Power pack 3080, observe
the operating instructions for the ATS3080.
f Connect control boxes 3 to the customer-supplied
control unit à"Interface overview, control boxes" on
page17.
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Installation
10
f Connect Power pack 3080 1 to the ATS3080 2 and to
the power supply à"Interface overview, Power pack
3080" on page15.
f Connect compressed air connection 4 to the
compressed air supply system.
f Make sure that all the wiring is free of kinks.
f Check that compressed air connection 4 is secure and
leak-tight.
f Make sure that there is nothing to obstruct accessibility
to ATS3080 2 , Power pack 3080 1 , control boxes 3
and reel holders 5 .
5.1.5 Inserting the BMK closure chain guide
21
3
f Pull out locking pin 2 .
f Insert holder 1 of closure chain guide 3 .
f Allow locking pin 2 to lock firmly into place.
5.1.6 Inserting the closure reel
1 2
6
3
4
5
8
7
f Remove closure reel 1 from its packaging and remove
the protective mesh.
f Push in sleeve 2 of articulated shaft 3 and tilt bearing 4
inward.
f Insert closure reel 1 onto reel mount 8 . Note the coiling
position in this process.
; The closure reel 1 uncoils clockwise.
; The collar of the bearing 4 holds closure reel 1 on the
Bench mount kit horizontal 3080.
f Introduce closure chain 7 with the number facing up
into closure chain guide 6 .
f Feed closure chain 7 through closure chain guide 6 to
ATS3080 5 .
f Make sure that the closure chain 7 is not twisted.
7
9
5
f Open cover 9 of ATS3080 5 .
f Insert closure chain 7 into the ATS3080 5 to the point
of first engagement.
; The red LED in the display goes out.
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Installation
11
; The closure reel 7 locks firmly into place.
f Close cover 9 of ATS3080 5 .
5.1.7 Inserting the strap reel
9
8
1 2
5
6
3
4
7
f Push in sleeve 2 of articulated shaft 3 and tilt bearing 4
inward.
f Push brake block 1 up.
f Insert strap reel 9 onto reel mount 8 . Note the coiling
position in this process.
; Strap reel 9 uncoils anti-clockwise.
; The collar of reel brake 4 holds strap reel 9 on the
Bench mount kit horizontal 3080.
f Insert brake block 1 onto strap reel 9 .
10a
10b
5
10c
10c
6
11
f Feed strap 5 round deflection rollers 10b and 10a and
the deflection roller 10c .
f Feed strap 5 through the opening in guide rail 11 to
ATS3080 6 .
The digits (1 to 4) on the deflection rollers and the guide rail
indicate the sequence for guidance of the strap, àlabel on
the reel mount.
f Make sure that strap 5 is not twisted.
f With the teeth facing up, introduce the end of strap 5
into the opening of the ATS3080 6 .
f Close latch 7 on the ATS3080 6 .
; The red LED in the display goes out.
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Installation
12
5.2 Positioning
5.2.1 Positioning the material for bundling
f Make sure that the material for bundle is always in the
same position.
f Bundle the material neatly. Make sure there are no
projecting cable-tie ends.
f Make sure that the upper and lower jaws of the
ATS3080 are not obstructed.
90°
10 mm
f Guide the ATS3080 past the material to be bundled at an
angle of 90° to ensure that each binding is secure
without projecting cable-tie ends.
f Make sure that the straps are set with a minimum
distance of 10 mm.
NOTE
For correct binding, the ATS3080 always has to be centred
relative to the material to be bundled.
5.2.2 Geometries of materials for bundling
1
2
3
Diameter max. 80 mm
Rectangle sizes max. 34 mm x 72 mm
Square sizes max. 56 mm x 56 mm
5.3 Check of finished bindings
The HellermannTyton components cannot perform a check
of the finished bindings. An external monitoring system (e.g.
camera monitoring) is required for such checks.
5.4 Sequence of movements in normal operation
The sequence of movements as shown here is with Ø50 mm
jaws and a round object.
Start position
1
2
3
4
Step 1: Jaws 1 close.
Step 2: The strap forms a loop 2 round the material.
Step 3: The ATS3080 switches to reverse.
Step 4: Deflector 3 moves back, jaws open 4 .
Tensioning position
5
X
Step 5: The strap is tensioned round the material.
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Control unit
13
Step 6: The strap is cut off when the pre-set binding
strength is reached.
Step 7: The deflector advances.
Step 8: The ATS3080 5 returns to the start position.
5.4.1 Point-to-point path
Jaws Ø30 mm and
limiting block
15 mm
(5 mm without
pressure)
Jaws Ø50 mm and
limiting block
15 mm
(5 mm without
pressure)
Jaws Ø80 mm and
limiting block
22 mm
(5 mm without
pressure)
6 Control unit
The customer-supplied control unit accepts and
processes sensor signals from the Bench mount kit
horizontal 3080.
6.1 Precondition
The Bench mount kit horizontal 3080 is in the start
position, all sensors are correctly actuated.
• S-position: not actuated
• S-trigger: actuated
• S-pusher: not actuated
• S-jaw open: actuated
• S-ejector: actuated
6.2 Error messages
• Signal Error: One of the sensors is not correctly
actuated or jaws are blocked.
• Signal Error Jaw: Jaws remain closed. If this error
occurs, the ATS3080 will not retract – the cause of the
error message has to be eliminated beforehand.
6.3 Rectifying error
1
f Eliminate the cause of the error.
f Reset the ATS3080 à Operating Instructions for the
ATS3080
f Press the "Reset" button 1 on the Bench mount kit
horizontal 3080.
7 Maintenance
7.1 Important notes
Regular maintenance is essential to ensure that the
ATS3080 remains in safe working order (see the
maintenance schedule in the operating instructions for
the ATS3080).
CAUTION
Crush hazard when jaws close
f Do not insert fingers between upper and lower jaws.
f Do not rest your foot on the foot pedal.
f Always keep the Power pack 3080 switched off while
performing maintenance work.
f Depressurise the compressed-air system and secure it
against unintentional restart.
7.2 Spare parts
Spare parts and accessories can be ordered directly from
your national HellermannTytonrepresentative
à website www.HellermannTyton.de.
7.3 General maintenance activities
The activities involved in maintenance of the ATS3080 and
the Power pack 3080 are described in the operating
instructions for the ATS3080 (see the "Maintenance" section
in the operating instructions for the ATS3080).
f Check the ATS3080 and the accessories regularly for
proper function.
f Check the compressed-air lines for leaks (see the
operating instruction for the compressed-air equipment).
f Dispose of waste materials at regular intervals.
The compressed-air equipment is not included in the scope
of supply.
f Replace faulty compressed-air lines immediately.
f Check electrical wiring for damage.
f Replace faulty wires immediately.
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Maintenance
14
7.4 Changing the strap reel
10
9
1 2
5
6
3
4
78
f Push brake block 1 up.
f Push in sleeve 2 of articulated shaft 3 and tilt bearing 4
inward.
f Remove the empty strap reel and dispose of it in
accordance with local regulations.
Empty reels are not taken back by the manufacturer.
f Insert full strap reel 10 onto reel mount 9 . Note the
coiling position in this process.
; Strap reel 10 uncoils anti-clockwise.
; The collar of reel brake 4 holds strap reel 10 on the
Bench mount kit horizontal 3080.
f Insert brake block 1 onto strap reel 10 .
f Feed strap 5 round the deflection rollers and through
the opening in guide rail 8 to ATS3080 6 , à"Inserting
the strap reel" on page11.
The digits (1 to 4) on the deflection rollers and the guide rail
indicate the sequence for guidance of the strap, àlabel on
the reel mount.
f Make sure that strap 5 is not twisted.
f With the teeth facing up, introduce the end of strap 5
into the opening of the ATS3080 6 .
f Close latch 7 on the ATS3080 6 .
; The red LED in the display goes out.
7.5 Changing the closure reel
1 2
5
6
7
3
4
f Push in sleeve 2 of articulated shaft 3 and tilt bearing 4
inward.
f Remove the empty closure reel and dispose of it in
accordance with local regulations.
Empty reels are not taken back by the manufacturer.
f Insert full closure reel 1 onto reel mount 7 . Note the
coiling position in this process.
; Closure reel 1 uncoils clockwise.
f Pull sleeve 2 of articulated shaft 3 outward.
; The collar of reel brake 4 holds closure reel 1 on the
Bench mount kit horizontal 3080.
f Introduce closure chain 6 with the number facing up
into closure chain guide 5 .
f Feed closure chain 6 through closure chain guide 5 to
ATS3080 6 .
f Make sure that the closure chain is not twisted.
6
9
8
f Open cover 9 of ATS3080 8 .
f Insert closure chain 6 into the ATS3080 8 to the point
of first engagement.
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Technical data
15
; The red LED in the display goes out.
; The closure reel 6 locks firmly into place.
f Close cover 9 of ATS3080 8 .
8 Technical data
Unless otherwise indicated, all sizes are rounded off and
stated in millimetres.
HellermannTyton offers special CAD models for planning
integration into automatic systems.
8.1 Interface overview, Power pack 3080
SignalPower
ATS3080 Power Pack
6
1 2 3 4
5
1 Socket for power cable
2 Fuse
3 Socket for connection to ATS3080
4 Signal LED
Green: Operating voltage applied
5 LED indicator Power
Green: Power pack 3080 switched on
6 Main switch
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Technical data
16
8.2 Bench mount kit horizontal 3080
1253
434
260659
920
Weight with ATS3080 and reels (full) approx. 22.0 kg
Weight (empty) approx. 14.0 kg
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Technical data
17
8.3 Control boxes
Voltage supply 24 V , min. 500 mA
Compressed air supply 5–7 bar, oil-free
Compressed air con-
sumption rate
with stroke, dia. 80 jaws approx. 0.4m³/h at
5bar inlet pressure, 1500 cycles/h
8.3.1 Interface overview, control boxes
X2 X3 X4X1
X1 Control unit, customer-supplied
X2 Control unit, customer-supplied
X3 Control unit, customer-supplied
X4 Reset button
See circuit diagram for pinouts.
8.3.2 Connector pinouts, control boxes
Socket X1
PIN 1 = start signal
PIN 2 = +24 V
1
2
PIN 1
Start
PIN 2
Socket X2
PIN 1 = 0 V
PIN 3 = +24 V
1
25
34
Power supply Bench mount kit horizontal 3080
Socket X3
PIN 1 =
PIN 2 = 0 V
PIN 3 = Error signal
PIN 4 = Error jaw
PIN 5 = OK signal
1
52
43
PIN 2
PIN 3
PIN 4
PIN 5
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Technical data
18
8.4 Connection plan
1
2
7
4
3
6
X3X2X1
5
1 Power supply, Power pack 3080
2 Compressed air connector
3 Control boxes
4 ATS3080
5 Connecting cable
6 Control unit, customer-supplied
7 Power pack 3080
Connector pinouts, X1 to X3, à"Interface overview, control
boxes" on page17
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Technical data
19
8.5 Circuit diagram
GBDE
Assembly instructions Bench mount kit, horizontal, 3080 • 03-2017 • v02 • 102-01011
Declaration of conformity
20
9 Declaration of conformity
EC Declaration of Conformity
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
HellermannTyton Autotool System 3080 Assembly Instructions Manual
- Catégorie
- Kits de voiture
- Taper
- Assembly Instructions Manual
dans d''autres langues
- English: HellermannTyton Autotool System 3080
- Deutsch: HellermannTyton Autotool System 3080
Documents connexes
-
HellermannTyton Bench mount kit automatic 3080 Le manuel du propriétaire
-
-
-
-
-
-