Tweco Robotics Light Weight Quick Robotics Torch Guide d'installation

50

60

Hz

1

PHASE

GTAW

SMAW

INVERTER

CC

DC

115

V

230

V

QUICK ROBOTICS

TORCH

Installation Guide and

Replacement Parts Manual

LIGHT WEIGHT

English

Français

Español

Revision No: A

Issue Date: November 11, 2008 Manual No: SM-QRLTORCH

Congratulations on your new Tweco® Robotics product. We are proud

to have you as our customer and will strive to provide you with the

best service and reliability in the industry. This product is backed by

our extensive warranty and world-wide service network. To locate your

nearest distributor or service agency call 800-426-1888, or visit us on

the web at www.tweco.com.

This Operating Manual has been designed to instruct you on the

correct use and operation of your Tweco

®

Robotics product. Your

satisfaction with this product and its safe operation is our ultimate

concern. Therefore, please take the time to read the entire manual,

especially the Safety Precautions. They will help you to avoid

potential hazards that may exist when working with this product.

YOU ARE IN GOOD COMPANY!

The Brand of Choice for Contractors and Fabricators Worldwide.

Tweco® Robotics is a Global Brand of Arc Welding Products for

Thermadyne Industries Inc. We manufacture and supply to major

welding industry sectors worldwide including; Manufacturing,

Construction, Mining, Automotive, Aerospace, Engineering, Rural and

DIY/Hobbyist.

We distinguish ourselves from our competition through market-leading,

dependable products that have stood the test of time. We pride ourselves

on technical innovation, competitive prices, excellent delivery, superior

customer service and technical support, together with excellence in

sales and marketing expertise.

Above all, we are committed to develop technologically advanced

products to achieve a safer working environment within the welding

industry.

WE APPRECIATE YOUR BUSINESS!

!

WARNING

Read and understand this entire Manual and your employer’s safety practices before installing, operating, or

servicing the equipment.

While the information contained in this Manual represents the Manufacturer’s best judgment, the Manufacturer

assumes no liability for its use.

Light Weight Quick Robotics Torch

Installation Guide and Replacement Parts Manual

Instruction Manual Number SM-QRLTORCH

Published by:

Tweco

®

Products Inc.

2800 Airport Road

Denton, TX 76208

(940) 566-2000

www.tweco.com

Thermadyne Industries Inc.

Reproduction of this work, in whole or in part, without written permission of the publisher is prohibited.

The publisher does not assume and hereby disclaims any liability to any party for any loss or damage caused by any error or

omission in this Manual, whether such error results from negligence, accident, or any other cause.

Publication Date: November 11, 2008

Record the following information for Warranty purposes:

Where Purchased: ________________________

Purchase Date: ________________________

Equipment Serial #: ________________________

i

Quick ROBOtics light weight tORch

ii

SM-QRLTORCH

Table of Contents

SECTION 1:

SAFETY INSTRUCTIONS AND WARNINGS .................................................. 1-1

1.01 Welding Hazards .......................................................................................

1-1

1.02 Principal Safety Standards ........................................................................

1-3

1.03 Safety and Health ......................................................................................

1-3

SECTION 2:

INTRODUCTION AND DESCRIPTION ......................................................... 2-4

2.01 How to Use this Manual ............................................................................2-4

2.02 Receipt of Equipment ................................................................................2-4

2.03 Introduction ..............................................................................................

2-4

2.04 Standard Features .....................................................................................

2-4

SECTION 3:

Installation and Disassembly ................................................................. 3-6

3.01 Installation ...............................................................................................3-6

3.02 Disassembly .............................................................................................3-8

SECTION 4:

WIRING ........................................................................................... 4-9

SECTION 5:

MAINTENANCE .................................................................................5-10

SECTION 6:

TROUBLESHOOTING ..........................................................................6-11

SECTION 7:

QRL REPLACEMENT PARTS ..................................................................7-12

SECTION 8:

CONDUIT LINERS ..............................................................................8-14

SECTION 9:

FACTORY REPAIR CENTER ...................................................................9-15

LIMITED WARRANTY ................................................................................9-16

Quick ROBOtics light weight tORch

1-1

SM-QRLTORCH

SAFETY INSTRUCTIONS AND WARNINGS

5. All ground connections must be checked periodically

to determine that they are mechanically strong and

electrically adequate for the required current.

6. When engaged in alternating current, welding, or cutting

under wet conditions or warm surroundings where

perspiration is a factor, the use of reliable automatic

controls for reducing the no-load voltage is recommended

to reduce shock hazard.

7. When the welding or cutting process requires values of

open circuit voltages in alternating current machines

higher than 80 volts, and direct current machines higher

than 100 volts, means must be provided to prevent the

operator from making accidental contact with the high

voltage by adequate insulation or other means.

8. When welding is to be suspended for any substantial

length of time, such as during lunch or overnight, all

electrodes should be removed from the electrode

holder and the electrode holder carefully located so that

accidental contact cannot occur.

9. The holder must be disconnected from the power source

when not in use.

10. Never immerse Mig-Guns, electrode holders, tig torches,

plasma torches, or electrodes in water.

WARNING

SMOKE, FUMES AND GASES CAN BE DANGEROUS

TO YOUR HEALTH.

1.01 Welding Hazards

WARNING

ELECTRIC SHOCK CAN CAUSE INJURY OR

DEATH.

INSTALL AND MAINTAIN EQUIPMENT IN ACCORDANCE

WITH THE NATIONAL ELECTRICAL CODE (NFPA 70)

AND LOCAL CODES. DO NOT SERVICE OR REPAIR

EQUIPMENT WITH POWER ON. DO NOT OPERATE

EQUIPMENT WITH PROTECTIVE INSULATORS

OR COVERS REMOVED. SERVICE OR REPAIR TO

EQUIPMENT MUST BE DONE BY A QUALIFIED REPAIR

TECHNICIAN, OR TRAINED PERSONNEL ONLY.

1. Do not touch live electrical parts.

2. Do not touch an electrode with bare skin and electrical

ground at the same time.

3. Always keep welding gloves dry and in good condition.

NOTE

Aluminized protective clothing can become part

of the electrical path.

4. Keep oxygen cylinders, chains, wire ropes, cranes, hoists,

and elevators away from any part of the electrical path.

SECTION 1:

SAFETY INSTRUCTIONS AND WARNINGS

!

WARNING

SERIOUS INJURY OR DEATH may result if welding and cutting equipment is not properly installed, used and maintained.

Misuse of this equipment and other unsafe practices can be hazardous. The operator, supervisor and helper must

read and understand the following safety warnings and instructions before installing or using any welding or cutting

equipment.

The welding and cutting process is used in many potentially dangerous environments such as elevated heights, areas

of limited ventilation, close quarters, around water, in hostile environments, etc., and it is important that the operator(s)

are aware of the dangers associated with working in these types of conditions. Be certain that the operator(s) are

trained in safe practices for environments in which they are expected to work and under competent supervision.

It is essential that the operator, supervisor and all other personnel in the work area are aware of the dangers of the

welding or cutting process. Training and proper supervision are important for a safe work place. Keep these instructions

for future use. Additional recommended safety and operating information is referenced in each section.

Quick ROBOtics light weight tORch

1-2

SM-QRLTORCH

SAFETY INSTRUCTIONS AND WARNINGS

WARNING

WELDING SPARKS CAN CAUSE FIRES AND

EXPLOSIONS.

23. Causes of ﬁre and explosion are: combustibles reached by

the arc, ﬂame, ﬂying sparks, hot slag, or heated material.

Remove combustibles from the work area and/or provide

a ﬁre watch.

24

. Avoid oily or greasy clothing as sparks may ignite them. Have

a ﬁre extinguisher nearby, and know how to use it.

25.

Be alert to the danger of conduction or radiation. For

example, if welding or cutting is to be done on a metal

wall, partition, ceiling, or roof, precautions must be taken

to prevent ignition of combustibles on the other side.

26. Do not w

eld or cut containers that have held combustibles.

All hollow spaces, cavities and containers should be

vented prior to welding or cutting to permit the escape

of air or gases. Purging with inert gas is recommended.

27.

Never use oxygen in a welding torch. Use only inert

gases or inert gas mixes as required by the process. Use

of combustible compressed gases can cause explosions

resulting in personal injury or death. Arcing against any

compressed gas cylinder can cause cylinder damage or

explosion.

WARNING

NOISE CAN DAMAGE HEARING.

28. Noise from the air carbon-arc process can damage your

hearing. Wear protective hearing devices to ensure protection

when noise levels exceed OSHA standards. Adequate

hearing protection devices must be worn by operators and

surrounding personnel to ensure personal protection against

noise.

11. Keep smoke, fumes, and gases from the breathing area.

12. Fumes from the welding or cutting process are of various

types and strengths, depending on the kind of base metal

being worked on. To ensure your safety, do not breathe these

fumes.

13. Ventilation must be adequate to remove smoke, fumes, and

gases during the operation to protect operators and other

personnel in the area.

14. Vapors of chlorinated solvents can form the toxic gas

“Phosgene” when exposed to ultraviolet radiation from an

electric arc. All solvents, degreasers, and potential sources

of these vapors must be removed from the work area.

15. Fumes produced by welding or cutting, particularly in conﬁned

places, can cause discomfort and physical harm if inhaled over

an extended period of time.

16. Provide adequate ventilation in the welding or cutting area.

Use air-supplied respirators if ventilation is not adequate to

remove all fumes and gases. Never ventilate with oxygen.

Oxygen supports and vigorously accelerates ﬁre.

WARNING

ARC RAYS, HOT SLAG AND SPARKS CAN INJURE

EYES AND BURN SKIN .

17. The welding and cutting processes produce extreme localized

heat, and strong ultraviolet rays.

18. Never attempt to weld or cut without a welding helmet with

the proper lens. Ensure that the lens complies with federal

guidelines. A number 12 to 14 shade ﬁlter lens provides the

best protection against arc radiation. When in a conﬁned

area, prevent the reﬂected arc rays from entering around the

helmet.

19. Ensure all personnel in the work area are protected from arc

rays and sparks. Approved shielding curtains and appropriate

goggles should be used to provide protection to staff in the

surrounding area and operators of nearby equipment.

20. Unprotected skin should also be covered from arc rays, heat

and molten metal. Always wear protective gloves and clothing

that does not allow skin to become exposed. All pockets

should be closed and cuffs sewn shut. Leather aprons, sleeves,

leggings, etc., should be worn for out-of-position welding and

cutting or for heavy operations using large electrodes. High top

work shoes provide adequate protection from foot burns.

For added protection use leather spats.

21. Flammable hair preparations should not be used when

welding or cutting. Wear ear plugs to protect ears from

sparks.

22. Where the work area permits, the operator should be

enclosed in an individual booth painted with a ﬁnish of

low reﬂectivity such as zinc oxide. This is an important

factor for absorbing ultraviolet radiations, and lamp black.

The operator should be enclosed with non-combustible

screens similarly painted.

Quick ROBOtics light weight tORch

1-3

SM-QRLTORCH

SAFETY INSTRUCTIONS AND WARNINGS

Electric shock can cause injury or death.

Smoke, fumes, and gases can be dangerous to your

health.

Arc rays, hot slag, and sparks can injure or burn

unprotected eyes and skin.

Welding sparks can cause ﬁres and explosions.

Excessive noise can damage your hearing.

•

1.03 Safety and Health

NOTICE

Be sure to read and fully comprehend the safety

instuctions and warnings contained within section

1 of this manual before performing any welding

or cutting operations.

!

WARNING

Serious injury or death may result if welding and

cutting equipment is not properly installed, used

and maintained. Misuse of this equipment, or other

unsafe practices, can be hazardous.

SAFETY AND OPERATING REFERENCES

1. Code of Federal Regulations. (OSHA)

Section 29 Part 1910.95, 132, 133, 134, 139, 251, 252, 253, 254 and 1000.

U.S. Government Printing Ofﬁce, Washington, DC. 20402.

2. ANSl Z49.1 "Safety In Welding and Cutting."

3. ANSI Z87.1 "Practice for Occupational and Educational Eye and Face Protection."

4. ANSl Z88.2 "Standard Practice for Respiratory Protection."

American National Standards Institute, 1430 Broadway, New York, NY. 10018.

5. AWS F4.1 "Recommended Safe Practices for Welding and Cutting Containers."

6. AWS C5.3 "Recommended Practices for Air Carbon-Arc Gouging and Cutting."

The American Welding Society, 550 NW Lejeune RD., P.O.Box 351040, Miami FL. 33135

7. NFPA 51B “Fire Prevention in Cutting and Welding Processes.”

8. NFPA-7 “National Electrical Code.”

National Fire Protection Association, Battery Park, Quincy, MA. 02269.

9. CSA W117.2, "Safety in Welding, Cutting and Allied Processes."

Canadian Standards Association, 178 Rexdale Blvd., Rexdale, Ontario, Canada M9W 1R3.

1.02 Principal Safety Standards

!

Warning

This product contains chemicals, including lead,

or otherwise produces chemicals known to the

State of California to cause cancer, birth defects

and other reproductive harm.

Wash hands after handling.

(California Health & Safety Code § 25249.5 et

seq.)

Quick ROBOtics light weight tORch

2-4

SM-QRLTORCH

INTRODUCTION AND DESCRIPTION

2.01 How to Use this Manual

To ensure safe operation, read the entire manual, including

the chapters on safety instructions and warnings.

Throughout this manual, the words WARNING, CAUTION, and

NOTE may appear. Pay particular attention to the information

provided under these headings. These special annotations

are easily recognized as follows:

!

WARNING

A WARNING GIVES INFORMATION REGARDING

POSSIBLE PERSONAL INJURY.

CAUTION

A CAUTION refers to possible equipment

damage.

NOTE

A NOTE offers helpful information concerning

certain operating procedures.

2.02 Receipt of Equipment

When you receive the equipment, check it against the invoice

to make sure it is complete and inspect the equipment for

possible damage due to shipping. If there is any damage,

notify the carrier immediately to ﬁle a claim. Furnish complete

information concerning damage claims or shipping errors to

the location in your area listed in the inside back cover of this

manual. Include a full description of the parts in error.

If you want additional or replacement copies of this CD,

please contact Tweco

®

Robotics at the address and phone

number in your area listed on the inside back cover of this

manual. Include the Manual number (from page i) and CD

part number: 64-2601.

2.03 Introduction

The new Tweco

®

Robotics Quick Robotic Light Weight Torch

(QRL) offers the ideal torch for “Table Top” robots. It is designed

for everyday applications that require a lighter weight and

smaller proﬁle for robotic welding torch functions.

This factor is made possible due to the combination of a notable

reduction in the overall weight and size of the torch without

any affect on its superior reliability and repeatability.

The Quick Robotic Light Weight Torch gives the consumer the

same quality that is expected from all Tweco

®

Robotics

QRA

series torches, with close to half the weight and a significant

reduction in size.

2.04 Standard Features

Quick conductor tube lock for easy conductor tube

replacement.

40% lighter than the QRA series torch.

Lighter weight reduces the inertial effects on the torch

head and whipping action on the power cable giving

the torch more accuracy at arc initiation.

Smaller physical profile allows greater access to

conﬁned spaces.

Uses proven components of the QRA series.

Uses existing conductor tubes and consumables.

Compatible with existing mount arms.

OPTIONAL - Light Weight mount arm designed for the

Quick Robotic Light Weight Torch. Refer to Table 1.

•

SECTION 2:

INTRODUCTION AND DESCRIPTION

Quick ROBOtics light weight tORch

2-5

SM-QRLTORCH

QRL Air-cooled Torch Assembly

The air-cooled QRL torch assembly uses the QTR 66 series air-cooled conductor tubes. The air-cooled power cable is rated

for 400 amperes with a 60% duty cycle.

• Sold Separately - RDML-2000-JC E-Stop Jumper Cable.

This cable enables the connection of the QRL Torch to the

RDM 2000 series “Tweco

®

Robotics Deﬂection Mount”.

(Stock No. 3044-1860)

Figure 1: QRL Series “Air-cooled” Assembly

INTRODUCTION AND DESCRIPTION

Table 1: Light Weight Mount Arms

Part No. Stock No. Description

RDML - A -180 3500-1460 180° RDM Light Weight Mount Arm

RDML - A -180L 3500-1461 180° (Long) RDM Light Weight Mount Arm

RDML - A - 22 3500-1462 22° RDM Light Weight Mount Arm

RDML - A - 22L 3500-1463 22° (Long) RDM Light Weight Mount Arm

Quick ROBOtics light weight tORch

3-6

SM-QRLTORCH

INSTALLATION AND DISASSEMBLY

SECTION 3:

INSTALLATION AND DISASSEMBLY

3.01 Installation

1. Remove the torch and cable assembly from the carton,

and lay the assembly in a straight and untwisted position

on a workbench or ﬂoor.

2. Check to ensure all items, shown in Figure 1 are located

and identiﬁed. If any of the component parts are missing,

please notify the local Tweco

®

Welding Distributor or

Tweco

®

Products Customer Care Department at 1-800-

426-1888.

3. Verify that the overall cable length is correct to ﬁt between

the feeder - torch mount combination.

NOTE

The QRL torch and cable assemblies are furnished

with a 1-5/8” (41,28mm) Ø mounting diameter

and can be keyed in place into a ﬁxture if so

desired.

COVER TO CONCEAL

LOCKING SCREW

Figure 2 - Conductor Tube Locking Screw

4. Lift rubber cover to expose the conducter tube locking screw

located in the torch block assembly. Insert the factory supplied

5/32” T-handle allen wrench into the locking screw and rotate

counterclockwise until it stops.

5. Insert the conductor tube assembly into the torch block

assembly. The conductor tube is positively located into

the torch body by the use of two stainless steel alignment

pins.

6. Push the conductor tube assembly into place until the

locking screw can drive the back plug on the conductor tube

into its locked operating position. The conductor tube has

a machined locating groove around its rear diameter. This

groove will be ﬂush with the front housing when properly

installed as shown in Figure 3.

WHEN CONDUCTOR TUBE IS FULLY SEATED,

GROOVE ON TUBE SHOULD LINE UP

WITH EDGE OF INSULATING

SLEEVE

FIGURE 3 - CONDUCTOR TUBE INSTALLATION

Figure 3: Conductor Tube Installation

Figure 2: Conductor Tube Locking Screw

7. Remove the gas diffuser, tip and nozzle from the conductor

tube assembly.

8. The QRL torch assemblies are furnished with R45-3545

conduit and the rear connector plugs to ﬁt this series of

conduit. If a different conduit is required, refer to Page 7-1

listing the various conduits that are available.

Quick ROBOtics light weight tORch

3-7

SM-QRLTORCH

INSTALLATION AND DISASSEMBLY

CAUTION

Bending or distorting the conduit can cause wire

feed problems.

9. Remove the conduit from the package and uncoil

carefully.

10. Loosen the set screw located on the Tweco

®

, Panasonic

®

,

or Lincoln

®

rear connector plug to ensure the conduit will

feed through properly. For Miller style plug, remove the

threaded connector plug nipple from the rear connector

plug on the torch assembly. Refer to Figures 4A & 4B.

Figure 4a: Conduit Installation with Set Screw

Figure 4b: Conduit Installation with Set Screw

CONDUIT SET SCREW

Figure 5: Access Hole for Conduit Set Screw

13. When the conduit is completely through the torch and

conductor tube assembly, seat the brass conduit stop ﬁrmly

against the connector plug.

14. Tighten the set screw on the Tweco

®

, Panasonic

®

, or

Lincoln

®

rear connector plug. For Miller style rear connector

plug, re-install the threaded connector plug nipple. This

connection should be wrench tight.

15. Re-insert the factory-supplied 5/32” T-handle allen wrench

into the hole labeled “Conduit Set Screw” on the front

handle cap and rotate the set screw clockwise. The set

screw should be hand tight. Over tightening may cause

wire feed ability problems (reference Figure 5 for hole

location.

MILLER PLUG

CONDUIT ASSEMBLY

PLUG NIPPLE

FIGURE 4B - CONDUIT INSTALLATION WITH PLUG NIPPLE (MILLER STYLE)

SET SCREW

TWECO PLUG

CONDUIT ASSEMBLY

FIGURE 4A - CONDUIT INSTALLATION WITH SET SCREW

11. Insert the factory-supplied 5/32” T-handle allen wrench

through the hole on the aluminum front handle cap,

identiﬁed as “Conduit Set Screw” on the label, and rotate

the set screw counterclockwise until it stops rotating (see

ﬁgure 5).

12. Insert the exposed raw coil end of the conduit, factory

supplied, into the rear connector plug. Feed the conduit

through the gun and conductor tube assembly. If the conduit

attempts to hang up, rotate the conduit liner counterclockwise

while gently pushing.

Quick ROBOtics light weight tORch

4-8

SM-QRLTORCH

INSTALLATION AND DISASSEMBLY

16. Trim the conduit extending from the front of the conductor

tube assembly by following the steps below:

Method “A” – Using a tape measure or scale, mark

and cut the conduit to the cut length (1 5/16").

Refer to Figure 6 — Method “A”.

Method “B” – The diffusers have a machined

groove around the outer diameter. Position the

diffuser as shown in Figure 6 — Method “B” and

mark and cut the conduit.

•

1 5/16”

METHOD “A” METHOD “B”

17. After trimming to length, remove any obstructions

from the end of the conduit radius.

18. Re-install the diffuser, tip and nozzle onto the

conductor tube assembly.

19. Loosen the ﬁxture connection and insert the torch and

conductor tube assembly into position. The key located

on the torch body should be placed into the mating

keyway on the ﬁxture until it bottoms out against the

fixture plate. Tighten the connection to secure the

assembly in place.

Figure 7: Locating Key

3.02 Disassembly

To disassemble the torch and cable assembly from the ﬁxture,

reverse the steps noted in Section 3.01.

KEY

CUT LINE

20. Install the rear connector plug into the feeder.

21. Connect the rear control cable and front e-stop jumper

cable assemblies, if applicable.

22. The torch is now ready to place into operation.

Figure 6: Conduit Cut Length

Quick ROBOtics light weight tORch

4-9

SM-QRLTORCH

WIRING

SECTION 4:

WIRING

Connection Part No. Stock No.

Without Connector QRJC-010 3045-1241

Burndy (ABB) QRJC-020 3045-1242

4-pin Amp (Motoman) QRJC-030 3045-1243

5-pin DDK (Fanuc) QRJC-040 3045-1244

Table 2: E-Stop Adapter Jumper Cables

PIN 1

RED

NORMALLY OPEN

PIN 2

WHITE

COMMON

PIN 3

BLACK

NORMALLY CLOSED

PIN 4

---

PIN 5

---

PIN 6

---

PIN 7

---

PIN 8

---

PIN 9

---

CONTROL CABLE ASSEMBLY - (QRLXX-CC-F)

E-STOP ASSEMBLY - (QRL-RH-F)

SOCKET

BLUE

BLACK

BROWN

WHITE

RED

BLACK

RECEPTACLE AMP 206705-2

HOUSING AMP

207008-1

E-STOP

CONNECTOR

BLUE

BROWN

BLACK

The QRL torch is furnished with a receptacle housing mounted

on the front case. The 3-pin socket receptacle will accept

the RDML-2000-JC E-Stop Jumper Cable from the robot

deﬂection mount.

The receptacle is connected to a 3-wire cable that runs along

the inside of the inner protective jacket. The end of this cable

extends approximately 1ft. (.3m) out of the rear case and

comes standard with a 9-pin amp plug. Adapter jumper cables

are available to connect this cable to most robots (Table 2).

Wiring Schematic for E-Stop Cable

Quick ROBOtics light weight tORch

5-10

SM-QRLTORCH

MAINTENANCE

Each Use

Visual check of torch

Consumable parts

Weekly

Visually inspect the torch

body and consumables

Visually inspect the

cables and leads.

Replace as needed

3 Months

Clean

exterior

of power supply

6 Months

Replace all

broken parts

Visually check and

use a vacuum to carefully

clean the interior

Gas and

air lines

dwg-00032

Visually inspect the Wire

feed mechanisms

Warning!

Disconnect input power before maintaining.

Maintain more often

if used under severe

conditions.

Visual check of

regulator and pressure

The torch and conductor tube assemblies have o-rings for

seals. Lubrication of these o-rings should be done periodically

and periodical inspections should be made to ensure that the

o-rings do not degrade, allowing water and or shielding gas

leaks to occur. When removing the conductor tube from the

torch assembly, be sure the single o-ring located in the bottom

of the hole remains in place.

Contact tips and nozzles should be cleaned frequently.

Spatter buildup may cause bridging between nozzle and tip.

This could cause electrical shorting between the nozzle and

work piece as well as restricting gas ﬂow.

Regularly inspect the conductor tube, torch and cable

assembly for abrasions, cuts and undue wear. Replace or

repair any parts as needed.

SECTION 5:

MAINTENANCE

Quick ROBOtics light weight tORch

6-11

SM-QRLTORCH

TROUBLESHOOTING

SECTION 6:

TROUBLESHOOTING

Problem Possible Cause Corrective Action

Wire feed inconsistent or not

smooth.

1. Loose drive Rollers on feeder.

2. Dirty or plugged conduit.

3. Conduit pulled back from diffuser.

4. Sharp bends or kinks in conduit.

5. Machine improperly adjusted.

6. Spatter buildup on end of contact tip.

7. Loose contact tip or diffuser.

8. Excessively worn contact tip.

9. Loose ground cable or ground clamp.

1. Tighten drive rollers.

2. Replace conduit.

3. Reposition conduit and tighten front

screw.

4. Remove and replace conduit.

5. Reset machine per machine and wire

manufacturers’ recommendations.

6. Clean or replace contact tip.

7. Tighten contact tip and diffuser plier

tight.

8. Replace contact tip.

9. Tighten or replace as required.

Torch and cable assembly is

running hot.

1. Loose power connection.

2. Loose or undersize ground cable or

ground clamp.

3. Conductor tube not tight in torch block.

4. Loose contact tip or diffuser.

5. Operating torch and cable assembly

above recommended amperage rating.

6. Power cable assembly damaged.

7. Restricted water ﬂow (only QRW and

QRWA series torch).

1. Inspect complete torch and cable for

loose connections and tighten.

2. Tighten or replace as required.

3. Tighten stainless setscrew in torch

block.

4. Tighten contact tip and diffuser.

5. Readjust machine to correct setting for

size of torch being used.

6. Inspect and replace accordingly.

7. Inspect water lines for any excessive

bends.

Robot will not start. 1. Deﬂection mount not at “home”

position.

2. Check E-stop cable connection.

1. Check to ensure the mount arm and

mount location.

2. Check E-stop cable connection.

Porous weld. 1. Poor or improper gas ﬂow.

2. Moisture from torch/conductor tube.

3. Dirty or contaminated wire.

4. Base metal contamination.

1. Check gas ﬂow out of conductor tube

nozzle. Check for leaks or restrictions

in gas hoses and connections.

2. Check O-rings on conductor tube and

torch block. Check the torch block for

any scarring, gouges to the surface.

3. Change wire.

4. Replace base metal.

Quick ROBOtics light weight tORch

7-12

SM-QRLTORCH

QRL REPLACEMENT PARTS

QRL Series Replacement Parts

Item No. Part No. Stock No. Description

1 QRLMS 3045-1709 QRL Mount Sleeve (Includes 4, A & B)

2 QRLH 3045-1710 QRl Case

3 QR106-RLS 3045-1341 Conductor Tube Locking Screw (Qty. 5)

4 QTRMS-BS 3045-1156 Woodruff Keys (Qty. 5)

5 QRL106S 3045-1347 Conduit Screw

6 QRLRH 3045-1706 QRL Receptacle Housing Assembly (Includes C)

7 QRLCS 3045-1700 Locking Screw Cover for QRL series

20

21

22

23

15

D

16

14

17

19

18

13

8

12

10

9

3

5

3

5

26

11

25

1

2

6

7

24

4

C

B

A

B

E

F

SECTION 7:

QRL REPLACEMENT PARTS

Quick ROBOtics light weight tORch

7-13

SM-QRLTORCH

QRL REPLACEMENT PARTS

Item No. Part No. Stock No. Description

8 QRL1004PC 3045-1702 QRL Series Front Block & Cable (4 ft. long) (Includes 3, E & 5)

QRL1006PC 3045-1703 QRL Series Front Block & Cable (6 ft. long) (Includes 3 , E & 5)

9 QRL-SPS 3045-1199 Front Strain Relief Spring (Includes B & F)

10 QRLRCS 3045-1701 QRL Strain Relief Cap & Spring

11 QRL04CC 3045-1704 QRL Control Cable Assembly (4 ft. long) (Includes E)

QRL06CC 3045-1705 QRL Control Cable Assembly (6 ft. long) (Includes E)

12 QRL04J 3045-1707 QRL Cable Cover (4 ft. long) (Includes F)

QRL06J 3045-1708 QRL Cable Cover (6 ft. long) (Includes F)

13 QRA-CS 3045-1239 Rear Case Assembly

14 R174MH 2035-2109 Miller Connector Plug

R176MH 2060-2184 Miller Connector Plug

15 R175M-N045 2050-2181 Miller Plug Nipple, 0.045” (1,0mm) Wire (Use w/R176MH)

R174M-N045 2040-2192 Miller Plug Nipple, 0.045” (1,0mm) Wire (Use w/R174MH)

16 R175M-N116 2050-2182 Miller Plug Nipple, 0.062” (1,6mm) Wire (Use w/R176MH)

R174M-N116 2040-2191 Miller Plug Nipple, 0.062” (1,6mm) Wire (Use w/R174MH)

17 176S-H 2060-2177 Tweco® Connector Plug

350-174H 2035-2110 Tweco® Connector Plug (Uses R44 series Conduit)

18 QTR176LH 2086-2624 Lincoln Connector Plug (2.71” - 68,83mm OAL.)

EL176LH 2060-2680 Lincoln Connector Plug (3.84” - 97,54mm OAL.)

19 350-174PH 2035-2172 Panasonic Connector Plug (Uses R44 series Conduit)

20 XQRL1004PC 3045-1395 QRL Front Block & Cable (4 ft. long-Euro) (Includes 3, E & 5)

XQRL1006PC 3045-1396 QRL Front Block & Cable (6 ft. long-Euro) (Includes 3, E & 5)

21 XQRA-CS 3045-1240 Rear Case Assembly (Includes D)

22 174X-2S 2040-2177 Euro-Kwik Nut

23 E171-1TS 2011-2172 Euro-Kwik Adapter

24 -- -- Conduit (Refer to page 7-1)

25 QTR-TOOLS 2062-2034 Tool Kit

26 -- -- E-stop Jumper Cable Assembly

QRJC-010 3045-1241 Without Connector - 3 ft. (91cm) Long

QRJC-020 3045-1242 With Burndy Connector - 3 ft. (91 cm) Long

QRJC-030 3045-1243 With 4-pin Amp Connector - 3 ft. (91 cm) Long

QRJC-040 3045-1244 With 5-pin DDK Connector - 3 ft. (91 cm) Long

Standard Non-Sellable Parts

These standard parts are not sellable items and should be purchased at a local hardware or fastener supplier.

Item No. Description

A 1/4 - 20 x 3/8 Half Dog Point Set Screw

B 1/4 - 20 x 1/4 Flat Point Socket Head Set Screw

C 10 - 32 x 1/2 SS Socket Head Cap Screw

D M4 x 0.7 x 5.9 Cheese Head Screw

E 7.6L x 0.190W Cable Tie Panduit CBR2S

F 4.1L x 0.098W Cable Tie Panduit CBR1M

QRL Series Replacement Parts (cont.)

Quick ROBOtics light weight tORch

8-14

SM-QRLTORCH

CONDUIT LINERS

NOTE

Part/Stock numbers with a (WN) reference signify

“Wire, Nylon Wrapped”.

SECTION 8:

CONDUIT LINERS

MACHINED CO NDUIT STOP

WIRE CONDUIT

NEOPREN E SEAL

HEAT SHRINK

R45 SERIES CONDUITS

STEEL WELDING WIRE ALUMINUM WELDING WIRE

Part No. Part No.

Wire Size Stock No. Length Wire Size Stock No. Length

.035

in

/ .045

in

R45-3545-1 1

ft

.035

in

/ .045

in

R45WN-3545-4 4

ft

0.9

mm

/ 1.2

mm

1450-1023 .3

m

0.9

mm

/ 1.2

mm

1450-1041 1.2

m

.035

in

/ .045

in

R45-3545-4 4

ft

.035

in

/ .045

in

R45WN-3545-8 8

ft

0.9

mm

/ 1.2

mm

1450-1024 1.2

m

0.9

mm

/ 1.2

mm

1450-1042 2.4

m

.035

in

/ .045

in

R45-3545-8 8

ft

.035

in

/ .045

in

R45WN-3545-15 15

ft

0.9

mm

/ 1.2

mm

1450-1025 2.4

m

0.9

mm

/ 1.2

mm

1450-1043 4.6

m

.035

in

/ .045

in

R45-3545-15 15

ft

1/16

in

R45WN-116-8 8

ft

0.9

mm

/ 1.2

mm

1450-1026 4.6

m

1.6

mm

1450-1044 2.4

m

.052

in

/ 1/16

in

R45-116-1 1

ft

1/16

in

R45WN-116-15 15

ft

1.53

mm

/ 1.6

mm

1450-1028 .3

m

1.6

mm

1450-1045 4.6

m

.052

in

/ 1/16

in

R45-116-4 4

ft

1.53

mm

/ 1.6

mm

1450-1029 1.2

m

.052

in

/ 1/16

in

R45-116-8 8

ft

1.53

mm

/ 1.6

mm

1450-1030 2.4

m

.052

in

/ 1/16

in

R45-116-15 15

ft

1.53

mm

/ 1.6

mm

1450-1031 4.6

m

Quick ROBOtics light weight tORch

9-15

SM-QRLTORCH

FACTORY REPAIR CENTER

SECTION 9:

FACTORY REPAIR CENTER

Tweco

®

Robotics Factory Repair Center (FRC) offers a repair service for our customers on the various cable assemblies and peripheral

products. The majority of our consumers do not want to spend the time involved with repairs and generally do not have the necessary

equipment and tools to perform repairs.

Other key beneﬁts in considering the “FRC” service repairs on your product:

All products will be rebuilt and tested following the established test procedures and speciﬁcations for the speciﬁc

product.

All repairs are done using original Tweco

®

Robotics parts to ensure maximum product performance.

Our FRC has highly-trained employees utilizing the appropriate tools and test equipment.

30-day warranty on the newly installed parts and labor on all cable assemblies.

30-day warranty on QRM-100, QRM-3 and RDM-2000 peripherals.

60-day warranty on QRC-2000 and QWT-120 peripherals.

Factory Repair Center

Domestic Toll Free Phone Number: 1-800-426-1888

Fax Number: 1-620-229-9926

•

Quick ROBOtics light weight tORch

16

SM-QRLTORCH

Statement of Warranty

LIMITED WARRANTY: THERMADYNE

®

warrants that its products will be free of defects in workmanship or material. Should

any failure to conform to this warranty appear within the time period applicable to the THERMADYNE products as stated below,

THERMADYNE shall, upon notiﬁcation thereof and substantiation that the product has been stored, installed, operated, and

maintained in accordance with THERMADYNE’s speciﬁcations, instructions, recommendations and recognized standard industry

practice, and not subject to misuse, repair, neglect, alteration, or accident, correct such defects by suitable repair or replacement,

at THERMADYNE’s sole option, of any components or parts of the product determined by THERMADYNE to be defective.

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING

ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

LIMITATION OF LIABILITY: THERMADYNE shall not under any circumstances be liable for special or consequential damages,

such as, but not limited to, damage or loss of purchased or replacement goods, or claims of customers of distributor (hereinafter

the “Purchaser”) for service interruption. The remedies of the Purchaser set forth herein are exclusive and the liability of

THERMADYNE with respect to any contract, or anything done in connection therewith such as the performance or breach

thereof, or from the manufacture, sale, delivery, resale, or use of any goods covered by or furnished by THERMADYNE whether

arising out of contract, negligence, strict tort, or under any warranty, or otherwise, shall not, except as expressly provided

herein, exceed the price of the goods upon which such liability is based.

THIS WARRANTY BECOMES INVALID IF REPLACEMENT PARTS OR ACCESSORIES ARE USED WHICH MAY IMPAIR

THE SAFETY OR PERFORMANCE OF ANY THERMADYNE PRODUCT.

THIS WARRANTY IS INVALID IF THE PRODUCT IS SOLD BY NON-AUTHORIZED PERSONS.

This warranty is effective for the time stated in the Warranty Schedule beginning on the date that the authorized distributor

delivers the products to the Purchaser.

Warranty repairs or replacement claims under this limited warranty must be submitted by an authorized THERMADYNE repair

facility within thirty (30) days of the repair. No transportation costs of any kind will be paid under this warranty. Transportation

charges to send products to an authorized warranty repair facility shall be the responsibility of the Purchaser. All returned

goods shall be at the Purchaser’s risk and expense. This warranty supersedes all previous THERMADYNE warranties.

La page charge ...

Tweco Robotics Light Weight Quick Robotics Torch Guide d'installation

Tweco Robotics Light Weight Quick Robotics Torch Guide d'installation

dans d''autres langues

Documents connexes

Autres documents