Home Styles 5530-55 Assembly Instructions

Taper
Assembly Instructions

Ce manuel convient également à

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
20 05530 0553
Bunk Bed
Cartons 20 05530 0551 and 0552 are also needed for assembly.
Small Hex Wrench
1 pc.
Hex Wrench
1 pc.
M6x40
Head Cap Bolt
20 pcs. (+1 extra)
Angled Washer
16 pcs. (+1 extra)
M6x30
Head Cap Bolt (short)
10 pcs. (+1 extra)
M6x70
Head Cap Bolt (medium)
6 pcs. (+1 extra)
Cross Dowel
8 pcs. (+1 extra)
M6x90
Head Cap Bolt (long)
2 pcs. (+1 extra)
Metal Pin
4 pcs.
M8x25
Wood Screw
56 pcs. (+1 extra)
K.
Front Guardrail
2 pcs.
L.
Back Guardrail
2 pcs.
M.
Rail
2 pcs.
N.
Leg
2 pcs.
O.
Support
2 pcs.
P.
Support
1 pc.
M6x60
Head Cap Bolt
for Leg
2 pcs. (+1 extra)
I.
Upper Front Panel
1 pc.
G.
Lower Front Panel
1 pc.
H.
Lower Back Panel
1 pc.
J.
Upper Back Panel
1 pc.
Q.
Ladder
1 pc.
Assembly Instructions 2/6
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 3
Attach Legs (N) to Rails (M)
with Head Cap Bolts for Leg.
(See Figure 2)
Figure 2
M
M
N
N
Head Cap Bolt
for Leg
STEP 1
Attach Lower Front Panel (G) and
Lower Back Panel (H) to Lower End
Panel (A) with Angled Washers and
Head Cap Bolts, tightening bolts only
halfway. (See Figure 1)
A
G
H
Angled Washer
Head Cap Bolt
B
Angled Washer
Head Cap Bolt
STEP 2
Attach Lower End Panel (B) to
unit with Angled Washers and
Head Cap Bolts, tightening
bolts only halfway.
Tighten all bolts used
in Steps 1 and 2.
Figure 1
Assembly Instructions 3/6
Figure 4
STEP 5
Attach Lower Slats (C) to unit with Wood Screws.
(See Figure 3)
Level unit by adjusting the adjustable
levelers on bottom of legs. (See Figure 4)
Wood Screw
C
STEP 4
Insert units from Step 3 into unit from Step 2.
Figure 3
Assembly Instructions 4/6
STEP 6
Attach Upper Back Panel (J) and Back
Guardrails (L) to Support (O) with Head
Cap Bolts (short), tightening bolts only
halfway.
J
L
L
O
Head Cap Bolt (short)
STEP 7
Attach unit and Upper Front Panel (I) to
Upper End Panel (D) with Cross Dowels,
Head Cap Bolts (medium), Angled Washers
and Head Cap Bolts, tightening bolts
only halfway. (See Figure 5)
D
I
Angled Washer
Head Cap Bolt
Head Cap Bolt (medium)
Cross Dowel
E
STEP 8
Attach Upper End Panel (E) to unit with
Cross Dowels, Head Cap Bolts (medium),
Angled Washers and Head Cap Bolts,
tightening bolts only halfway.
Tighten all bolts used in Steps 6, 7 and 8.
Figure 5
Angled Washer
Head Cap Bolt
Head Cap Bolt (medium)
Cross Dowel
Assembly Instructions 5/6
STEP 9
Attach Front Guardrails (K) to Support (O)
with Head Cap Bolts (short), tightening
bolts only halfway.
Attach Support (P) to unit with
Cross Dowels and Head Cap Bolts (long),
tightening bolts only halfway.
O
P
K
K
Head Cap Bolt (short)
Head Cap Bolt (long)
Cross Dowel
STEP 10
Attach unit to unit from
Step 8 with Head Cap
Bolts (short), Cross Dowels
and Head Cap Bolts (medium),
tightening bolts only halfway.
Tighten all bolts used
in Steps 9 and 10.
Head Cap Bolt (medium)
Cross Dowel
Head Cap Bolt (short)
F
Wood Screw
STEP 11
Attach Upper Slats (F) to unit with Wood Screws.
Assembly Instructions 6/6
Metal Pin
Full length guardrail
STEP 12
Insert Metal Pins into pre-drilled holes of unit from Step 5.
Attach unit from Step 11 to unit from Step 5 with Metal Pins.
Note: If back of bunk bed is placed next to a wall, the full length guardrail must
be placed against the wall to prevent entrapment between bunk bed and wall.
Q
Head Cap Bolt
STEP 13
Attach Ladder (Q) to unit with Head Cap Bolts, tightening bolts only halfway.
Tighten all bolts used in this step.
IMPORTANT
Use only mattress which is 74” – 75” long and 37 1/2" – 38 1/2" wide on upper bunk.
Use only mattress which is 74” – 75” long and 52 1/2“– 53 1/2" wide on lower bunk.
Use only mattress which is 10” or less thick on upper bunk.
Replacement parts, including additional guardrails may be obtained from
Home Styles Customer Service at www.homestyles-furniture.com.
Important
Follow the information on the warnings appearing
on the upper bunk end structure and on the carton.
Do not remove warning label from bed.
Always use the recommended size mattresses to
help prevent the likelihood of entrapment or falls.
Surface of mattress must be at least 5” (127 mm) below the upper edge of guardrails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other components
are in their proper position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Prohibit more than one person on upper bunk.
Always use the ladder for entering and leaving the upper bunk.
Do not use substitute parts. Contact Home Styles Customer Service
at www.homestyles-furniture.com for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guardrails on both long sides of the upper bunk. If the bunk bed
will be placed next to a wall, the guardrail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and wall.
The use of water or sleep flotation mattresses is prohibited.
STRANGULATION HAZARD – Never attach or hang items to any
part of the bunk bed that are not designed for use with the bed;
for example, but not limited to, hooks, belts, and jump ropes.
Keep these instructions for future reference.
Safety Warnings
IMPORTANTES
Importantes
Utilisez uniquement des matelas qui est de 74" – 75"
de long et 37 1/2" – 38 1/2" de large sur la couchette.
Utilisez uniquement des matelas qui est de 74" – 75"
de long et 52 1/2“ – 53 1/2" de large sur des lits superposés.
Utilisez uniquement des matelas qui est de 10" ou moins épais sur la couchette.
Pièces de remplacement, y compris garde-corps supplémentaires peuvent être
obtenus à partir de Home Styles service à la clientèle au www.homestyles-furniture.com.
Avertissements de Sécurité
Suivez les informations sur les mises en garde figurant sur la partie
supérieure de la structure d'extrémité et superposés sur la boîte.
Ne pas retirer l'étiquette d'avertissement du lit.
Utilisez toujours la taille recommandée du matelas pour
aider à prévenir le risque de coincement ou de chutes.
La surface du matelas doivent être d'au moins 5" (127 mm) sous le bord supérieur du garde-corps.
Ne permettez pas aux enfants de moins de 6 ans d'utiliser les lits superposés.
Vérifier régulièrement et s'assurer que les garde-corps, de bain, et d'autres composants sont
dans la bonne position, exempts de dommages, et que tous les connecteurs sont bien serrés.
Ne pas laisser les bousculades sur ou sous le lit et interdire de sauter sur le lit.
Interdire plus d'une personne sur la couchette supérieure.
Toujours utiliser l'échelle pour l'entrée et à la sortie de l'angle supérieur des lits superposés.
N'utilisez pas les articles de substitution. Contact service à la clientèle de Home Styles
au www.homestyles-furniture.com pour les pièces de remplacement.
Utilisation d'une lumière de nuit peut offrir une plus grande précaution
de sécurité pour un enfant à l'aide de la partie supérieure de la couchette.
Utilisez toujours des garde-corps sur les deux grands côtés de l'angle supérieur des lits
superposés. Si le lit est placé à côté du mur, le garde-corps qui court sur toute la longueur
du lit doit être placé contre le mur pour éviter la provocation policière entre le lit et le mur.
L'utilisation de l'eau ou de sommeil matelas de portance est interdite.
DANGER D'ÉTRANGLEMENT- Ne jamais attacher ou s'accrocher articles à n'importe quelle
partie du lit superposé qui ne sont pas conçus pour une utilisation avec le lit; par exemple,
mais non limité à, des crochets, des ceintures, et sauter des cordes.
Conservez ces instructions pour référence future.
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Home Styles 5530-55 Assembly Instructions

Taper
Assembly Instructions
Ce manuel convient également à

dans d''autres langues