Sony VPL-SC60U Manuel utilisateur

 1999 by Sony Corporation

3-866-603-11 (1)

VPL-SC60U

VPL-SC60E

VPL-SC60M

Operating Instructions

Mode d’emploi

Manual de instrucciones

FR

ES

LCD Data Projector

GB

VPL-SC60U/SC60E/SC60M

2 (GB)

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

To avoid electrical shock, do not open the

cabinet. Refer servicing to qualified

personnel only.

This symbol is intended to alert the

user to the presence of uninsulated

“dangerous voltage” within the

product’s enclosure that may be of

sufficient magnitude to constitute a risk

of electric shock to persons.

This symbol is intended to alert the

user to the presence of important

operating and maintenance (servicing)

instructions in the literature

accompanying the appliance.

English

WARNING

This label is located on the

rear of the Remote

Commander.

This label is located on the

rear of the Remote

Commander.

Caution

use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous

radiation exposure.

Notes

• Do not aim the laser at people or not look into the laser

transmitter.

• When the Remote Commander causes malfunction, consult

with qualified Sony personnel. We change the Remote

Commander as new one according to the guarantee.

This label is located on the

rear of the Remote

Commander.

Laser light shines out of this window.

For the customers in the USA

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own

expense.

You are cautioned that any changes or modifications not

expressly approved in this manual could void your authority

to operate this equipment.

For the customers of VPL-SC60E/SC60M

For the customers of VPL-SC60U

This label is located on the

side of the Remote

Commander.

LASER RADIATION

DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

RAYONNEMENT LASER

NE PAS REGARDER DANS LE FAISCEAU

APPAREIL A LASER DE CLASSE 2

LASER–STRAHLING

NIGHT IN DEN STRAHL BLICKEN

LASER KLASSE 2

MAX OUTPUT:1mW

WAVE LENGTH:645nm

LASER RADIATION

DO NOT STARE INTO BEAM

WAVE LENGTH:645nm

MAX OUTPUT:1mW

CLASS II LASER PRODUCT

COMPLIES WITH DHHS 21 CFR

SUBCHAPTER J

SONY CORPORATION

6-7-35 KITASHINAGAWA

SHINAGAWA-KU,TOKYO,JAPAN

A

MANUFACTURED;

CAUTION

AVOID EXPOSURE

-

LASER

RADIATION IS EMITTED

FROM THIS APERTURE.

3 (GB)

For the customers in Canada

This Class A digital apparatus complies with Canadian ICES-

003.

For the customers in the United Kingdom

WARNING

THIS APPARATUS MUST BE EARTHED

IMPORTANT

The wires in this mains lead are coloured in accordance with

the following code:

Green-and-Yellow: Earth

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be

connected to the terminal in the plug which is marked by the

letter E or by the safety earth symbol Y or coloured green or

green-and-yellow.

The wire which is coloured blue must be connected to the

terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the

terminal which is marked with the letter L or coloured red.

Voor de klanten in Nederland

Bij dit produkt zijn batterijen geleverd. Wanneer

deze leeg zijn, moet u ze niet weggooien maar

inleveren als KCA.

The socket-outlet should be installed near the equipment

and be easily accessible.

4 (GB)

5 (GB)

Table of Contents

English

GB

Overview

Precautions ............................................................... 6 (GB)

Features..................................................................... 8 (GB)

Location and Function of Controls......................... 9 (GB)

Front/Left Side ......................................................... 9 (GB)

Rear/Right Side/Bottom......................................... 12 (GB)

Remote Commander .............................................. 15 (GB)

Setting up and projecting

Installing the Projector........................................... 17 (GB)

Connecting.............................................................. 18 (GB)

Connecting with a Computer ................................. 18 (GB)

Connecting with a VCR/15k RGB/

Component Equipment ..................................... 20 (GB)

Projecting ................................................................ 22 (GB)

Adjustments and settings using the menu

Using the MENU...................................................... 25 (GB)

The PICTURE CTRL Menu ..................................... 26 (GB)

The INPUT SETTING Menu .................................... 28 (GB)

The SET SETTING Menu ........................................ 31 (GB)

Installation

Installation Example............................................... 33 (GB)

Unsuitable Installation ........................................... 34 (GB)

Notes on Installation .............................................. 35 (GB)

Maintenance

Maintenance............................................................ 36 (GB)

Replacing the Lamp ............................................... 36 (GB)

Cleaning the Air Filter ........................................... 37 (GB)

Troubleshooting ..................................................... 38 (GB)

Other

Specifications ......................................................... 40 (GB)

Index ........................................................................ 44 (GB)

6 (GB)

On safety

•Check that the operating voltage of your unit is identical with the voltage

of your local power supply. If voltage adaptation is required, consult with

qualified Sony personnel.

•Should any liquid or solid object fall into the cabinet, unplug the unit and

have it checked by qualified personnel before operating it further.

•Unplug the unit from the wall outlet if it is not to be used for several

days.

•To disconnect the cord, pull it out by the plug. Never pull the cord itself.

•The wall outlet should be near the unit and easily accessible.

•The unit is not disconnected to the AC power source (mains) as long as it

is connected to the wall outlet, even if the unit itself has been turned off.

•Do not look into the lens while the lamp is on.

•Do not aim the laser at people or not look into the laser transmitter.

•Do not place your hand or objects near the ventilation holes — the air

coming out is hot.

•Be careful not to catch your fingers by the adjuster when you lift up the

projector. Do not push hard on the top of the projector with the adjuster

out.

On illumination

•To obtain the best picture, the front of the screen should not be exposed

to direct lighting or sunlight.

•Ceiling-mounted spot lighting is recommended. Use a cover over

fluorescent lamps to avoid lowering the contrast ratio.

•Cover any windows that face the screen with opaque draperies.

•It is desirable to install the projector in a room where floor and walls are

not of light-reflecting material. If the floor and walls are of reflecting

material, it is recommended that the carpet and wall paper be changed to

a dark color.

On preventing internal heat build-up

After you turn off the power with the I /

u

key on the Remote Commander

or on the control panel, do not disconnect the unit from the wall outlet

while the cooling fan is still running.

Caution

The projector is equipped with ventilation holes (intake) on the right side

and ventilation holes (exhaust) on both sides and rear. Do not block or

place anything near these holes, or internal heat build-up may occur,

causing picture degradation or damage to the projector.

Precautions

7 (GB)

On cleaning

•To keep the cabinet looking new, periodically clean it with a soft cloth.

Stubborn stains may be removed with a cloth lightly dampened with a

mild detergent solution. Never use strong solvents, such as thinner,

benzene, or abrasive cleansers, since these will damage the cabinet.

•Avoid touching the lens. To remove dust on the lens, use a soft dry cloth.

Do not use a damp cloth, detergent solution, or thinner.

•Clean the filter at regular intervals.

On repacking

•Save the original shipping carton and packing material; they will come in

handy if you ever have to ship your unit. For maximum protection,

repack your unit as it was originally packed at the factory.

Overview

8 (GB)

Features

High portability

•Light weight/small size

This projector has come to miniaturized to 3.7 kg (8 lb 3 oz) of mass by

adopting magnesium die-casting body. And a carrying handle is equipped

with the projector. You can easily carry it with your computer.

High brightness, high picture quality

•High brightness

Adopting the new developed optical system and the 120 W UHP lamp

allow high brightness (light output 650 ANSI lumen) and excellent

uniformity on the picture.

•High resolution

Three 0.9-inch, about 480,000 pixel SVGA panels provide a resolution of

800 × 600 dots for RGB input and 600 horizontal TV lines for video

input.

Simple setup, easy presentation

•Simple setup with external equipment

This projector is preset for 38 kinds of input signals. You can project

images from an external signal source just by connecting the equipment

with the supplied cable and pushing the APA key.

•Remote Commander with mouse control and laser pointer functions

You can operate a computer with the Remote Commander since the unit

has a build-in mouse receiver. For your presentation, you can use the

laser pointer built in the Remote Commander as well.

Accepts various input signals

•Scan converter loaded

This projector has a build-in scan converter which converts the input

signal within 800 × 600 dots.

•Compatible input signals

This projector accepts video signals of the composite, S video, and

component as well as the 15k RGB, VGA

1)

, SVGA

1)

, XGA

1)

, and SXGA

1)

signals, which all can be displayed.

•Compatible with five color systems

NTSC, PAL, SECAM, NTSC 4.43

2)

, or PAL-M color system can be

selected automatically or manually.

..........................................................................................................................................................................................................

1) VGA, SVGA, XGA, and SXGA are registered trademarks of the International Business Machines Corporation,

U.S.A.

2) NTSC 4.43 is the color system used when playing back a video recorded on NTSC on a NTSC 4.43 system VCR.

9 (GB)

Location and Function of Controls

Front/Left Side

1 Zoom ring

Adjusts the size of the picture.

2 Focus ring

Adjusts the picture focus.

3 Lens

Open the lens shutter before projection.

4 Lens shutter

5 Front remote control detector

6 Adjuster

Used to keep the projector level if it is installed on an

uneven surface.

For details on how to use the adjusters, see “How to use the

adjuster” on page 13 (GB).

7 Ventilation holes (exhaust)

8 Left speaker

9 Control panel

For details, see “Control panel” on page 10 (GB).

0 Carrying handle

Pull up the handle from the projector for carrying.

Notes

•Do not place anything near the ventilation holes as it

may cause internal heat build-up.

•Do not place your hand or objects near the ventilation

holes — the air coming out is hot.

5

3

4

2

1

9

8

7

6

0

10 (GB)

Control panel

Location and Function of Controls

1

I / u

(

on / standby

)

key

Turns on and off the projector when the projector is in

the standby mode. The ON/STANDBY indicator lights

in green when the power is turned on.

When turning off the power, press the

I / u

key

twice following the message on the screen, or press

and hold the key for about one second.

For details on steps for turning off the power, see “To turn off

the power” on page 24 (GB).

2 Indicators

ON/STANDBY: Lights up or flashes under the

following conditions:

• Lights in red when the AC power cord is

plugged into the wall outlet. Once in the standby

mode, you can turn on the projector with the

I / u

key on the Remote Commander or on the

control panel.

• Lights in green when the power is turned on.

• Flashes in green while the cooling fan runs after

turning off the power with the

I / u

key. The fan

runs for about 90 seconds after turning off the

power.

The ON/STANDBY indicator flashes quickly

for the first 30 seconds.

During this time, you cannot turn the power

back on with the

I / u

key.

POWER SAVING: Lights up when the projector is

in the power saving mode. When POWER

SAVING in the SET SETTING menu is set to

ON, the projector goes into the power saving

mode if no signal is input for 10 minutes.

Although the lamp goes out, the cooling fan keeps

running. In the power saving mode, any key does

not function for the first 30 seconds. The power

saving mode is canceled when a signal is input or

any key is pressed.

TEMP (Temperature)/FAN: Lights up or flashes

under the following conditions:

• Lights up when temperature inside the projector

becomes unusually high.

• Flashes when the fan is broken.

LAMP/COVER: Lights up or flashes under the

following conditions:

• Lights up when the lamp has reached the end of

its life or becomes a high temperature.

• Flashes when the lamp cover or air filter cover is

not secured firmly.

For details on the LAMP/COVER and the TEMP/FAN

indicators, see page 39 (GB).

3 INPUT key

Selects the input signal. Each time you press the key,

the input signal switches between video/audio input

and INPUT A connector.

MENU

ENTERRESET

INPUT

ON

/STANDBY

LIGHT

APA

VOLUME I/ u

POWER

SAVING

TEMP

/FAN

LAMP

/COVER

5

2

6

7

8

0

9

1

4

3

11 (GB)

4 MENU key

Displays the on-screen menu. Press again to clear the

menu.

5 ENTER key

Enters the settings of items in the menu system.

6 RESET key

Resets the value of an item back to its factory preset

value. This key functions when the menu or a setting

item is displayed on the screen.

7 Arrow keys (V/v/B/b)

Used to select the menu or to make various

adjustments.

8 APA

(

Auto Pixel Alignment

)

key

Adjusts a picture to be projected clearest automatically

while a signal from the computer is input.

9 VOLUME +/– keys

Adjust the volume of the built-in speakers and output

level of the AUDIO OUT jack.

+ : Increases the volume.

– : Decreases the volume.

!º LIGHT key

Lights the back lighting (orange) for the keys on the

control panel when the power is turned on. Press again

to turn off the back lighting.

12 (GB)

1 Rear remote control detector

2 Ventilation holes (exhaust)

3 AC IN socket

Connects the supplied AC power cord.

4 Security lock

Connects to an optional security cable (Kensington’s).

The security lock corresponds to Kensington’s

MicroSaver Security System.

If you have any comment, contact

Kensington

2853 Campus Drive, San Mates, CA 94403

U.S.A.

Tel: 800-535-4242: extension 3348

Home page address: http://www.kensington.com/

5 75Ω termination switch (bottom)

Normally set to ON. Set it to OFF when the projector

is connected to a computer or a monitor.

6 Connector panel

For details, see page 14 (GB).

7 Lamp cover (bottom)

Rear/Right Side/Bottom

Location and Function of Controls

8 Adjuster button

9 Lens shutter dial

Turn the dial upward to open the lens shutter.

0 Right speaker

!¡ Ventilation holes (intake)/air filter cover

Notes

•Do not place anything near the ventilation holes as it

may cause internal heat build-up.

•Do not place your hand or objects near the ventilation

holes — the air coming out is hot.

1

3

4 6 75

8

9

0

!¡

2

13 (GB)

Adjuster button

How to use the adjuster

To adjust height

While lifting the projector, adjust the height so that the

projector becomes level.

Press the adjuster button while lifting the projector to

adjust the height.

To stand the projector firmly

The adjuster can be extended outwards to support the

projector firmly.

Notes

•Be careful not to let the projector down on your

fingers.

•Do not push hard on the top of the projector with the

adjusters out.

•If the adjuster is not stretched out toward right and

left sides of the projector, the unit may be

overbalanced.

14 (GB)

Connector panel

1 Video/audio input connector

Connect to external video equipment such as a VCR.

S VIDEO (mini DIN 4-pin): Connects to the S video

output (Y/C video output) of a video equipment.

VIDEO (phono type): Connects to the composite

video output of video equipment.

Note

If you connect video equipment to both the S VIDEO

and VIDEO jacks, the signal from the S VIDEO jack

is selected. When projecting the picture via the

VIDEO jack, be sure not to connect a cable to the S

VIDEO jack.

AUDIO input L (MONO)/R jacks (phono type):

Connect to the audio output of equipment. For

stereo equipment, use both the L and R jacks; for

monaural equipment, use the L (MONO) jack

only.

2 INPUT A connector

Connect to external equipment such as a computer.

You can control the mouse signal with the Remote

Commander.

INPUT A (HD D-sub 15-pin, female): Connects to

the monitor output on a computer using the

supplied cable. When inputting a component or,

15k RGB signal, use the optional cable.

MOUSE (13-pin): Connects to the mouse port on a

computer to control the mouse function using the

supplied mouse cable.

AUDIO IN (stereo minijack): Connects to the audio

output on a computer to input the audio signal.

3 AUDIO OUT jack (stereo minijack)

Connects to external active speakers.

The volume of the speakers can be controlled by the

VOLUME keys on the Remote Commander or the

control panel.

Right side

Location and Function of Controls

S VIDEO VIDEO

INPUT A MOUSE

AUDIO OUT

AUDIO IN

L-AUDIO-R

1

2

3

15 (GB)

The keys which have the same names as on the control

panel function identically.

You can control a connected computer using the

Remote Commander.

For details, see “Connecting with a Computer” on page

18 (GB).

Remote Commander

Notes on laser beam

•Do not look into the laser transmitter.

•Do not aim the laser at people.

1

I / u

key

2 INPUT key

3 LASER key

Emits laser beam from the laser transmitter when you

press this key.

4 Joy stick

Functions as a mouse of a computer connected to the

unit.

5 Arrow keys (V/v/B/b)

6 R CLICK key

Functions as a right button on a mouse. When

connected to a Macintosh

1)

computer, the R CLICK

key functions as a mouse button.

Front Rear

1) Macintosh is a registered trademark of Apple Computer, Inc.

..........................................................................................................................................................................................................

7 RESET key

8 VOLUME +/– keys

9 Strap holder

Attaches the supplied strap.

(Continued)

COMMAND

MUTING

I / u

INPUT

APA

MENU

LASER

V

bB

v

ENTER

RESET

VOLUME

+

–

R CLICK

PICTUREAUDIO

ONOFF

1

2

3

5

7

6

8

4

!¡

!™

!£

!¢

!∞

!§

!¶ !•

9, 0

!ª

16 (GB)

Location and Function of Controls

!º CONTROL S OUT jack (stereo minijack)

This jack does not operated with this unit.

Note

The Remote Commander does not function if the cable

is connected to this jack.

!¡ ENTER key

!™ MENU key

!£ APA (Auto Pixel Alignment) key

!¢ MUTING keys

Cut off the picture and sound.

PICTURE: Cuts off the picture. Press again to

restore the picture.

AUDIO: Cuts off the sound from speakers and

AUDIO OUT jack. Press again or press the

VOLUME + key to restore the sound.

!∞ COMMAND ON/OFF switch

When this switch is set to OFF, no key on the Remote

Commander function. This saves the battery power.

!§ Transmission indicator

Lights up when you press a key on the Remote

Commander.

This indicator does not light up when you use the laser

pointer.

!¶ Infrared transmitter

!• Laser transmitter

!ª L CLICK key

Functions as a left button on a mouse. When connected

to a Macintosh computer, the L CLICK key functions

as a mouse button.

Be sure to install

the battery from

the ’ side.

Battery installation

1 Push and slide to open the lid.

2 Install the two size AA (R6) batteries (supplied)

with the correct polarity.

3 Replace the lid.

Notes on batteries

•Make sure that the battery orientation is correct when

inserting batteries.

•Do not mix an old battery with a new one, or

different types of batteries.

•If you will not use the Remote Commander for a long

time, remove the batteries to avoid damage from

battery leakage. If batteries have leaked, remove

them, wipe the battery compartment dry and replace

the batteries with new ones.

Notes on Remote Commander operation

•Make sure that there is nothing to obstruct the

infrared beam between the Remote Commander and

the remote control detector on the projector.

•The operation range is limited. The shorter the

distance between the Remote Commander and the

projector is, the wider the angle within which the

commander can control the projector.

17 (GB)

This section describes the installation arrangements for installing the

projector.

Installing the Projector

Horizontal center

of the screen

The distance between the lens and the screen varies

depending on the size of the screen. Use the following table

as a guide.

Setting up and projecting

Screen size (inches) 40 60 80 100 120 150

Distance

Minimum 1.5 (5.1) 2.4 (7.7) 3.2 (10.4) 4.0 (13.0) 4.8 (15.7) 6.0 (19.7)

Maximum 1.8 (6.0) 2.8 (9.1) 3.7 (12.2) 4.7 (15.3) 5.6 (18.4) 7.0 (23.0)

Unit: m (feet)

For detailed information on installation measurements, see page 33 (GB).

18 (GB)

Connecting

Connecting with a Computer

This section describes how to connect the projector with a computer.

For details on how to connect a VCR, 15k RGB, or component equipment,

see page 20 (GB).

When the projector is connected to a computer, you can control the mouse

of a computer by the Remote Commander.

The R/L CLICK keys and joy stick function as follows.

Note

Make sure that there is nothing to obstruct the infrared beam between the

Remote Commander and the remoter control detector on the projector.

Key and joy stick

IBM PC/AT

a)

Macintosh

compatible, Serial

R CLICK (front) Right button Mouse button

L CLICK (rear) Left button Mouse button

Joy stick Corresponds with the movements of the mouse

a) IBM PC/AT is a registered trademark of International Business Machines

Corporation, U.S.A.

Also refer to the instruction manual of equipment to be connected.

Notes

•This unit accepts the VGA, SVGA, XGA, and SXGA signals. However,

we recommend you to set the output mode of your computer to the

SVGA mode for the external monitor.

•If you set your computer, such as a notebook type IBM PC/AT

compatible, to output the signal to both the display of your computer and

the external monitor, the picture of the external monitor may not appear

properly. In such cases, set the output mode of your computer to output

the signal to only the external monitor.

For details, refer to the operating instructions supplied with your computer.

When making connections, be sure to:

•turn off all equipment before making any connections.

•use the proper cables for each connection.

•insert the plugs of the cables properly; plugs that are not fully inserted

often generate noise. When pulling out a cable, be sure to pull it out from

the plug, not the cable itself.

Function

19 (GB)

S VIDEO VIDEO

INPUT A MOUSE

AUDIO OUT

AUDIO IN

L-AUDIO-R

S VIDEO VIDEO

INPUT A MOUSE

AUDIO OUT

AUDIO IN

L-AUDIO-R

When connecting with an IBM PC/AT compatible computer

When connecting with a Macintosh computer

Computer

Right side

SIC-S21 Mouse cable for serial port

(not supplied)

to serial port

to mouse port

SIC-S22 Mouse cable for PS/2 port (supplied)

to audio out

Stereo audio connecting

cable (not supplied)

to monitor out

Right side

SIC-S20 Mouse cable (supplied)

to mouse port

to audio out

Stereo audio connecting

cable (not supplied)

to monitor out

SMF-401 HD D-sub 15-

pin cable (supplied)

Signal adapter

(supplied)

For details on the DIP switch setting of the adapter, see page 42 (GB).

Note

Supplied mouse cables may not work properly according to your

computer.

or

Computer

SMF-401 HD D-sub 15-pin

cable (supplied)

20 (GB)

S VIDEO VIDEO

INPUT A MOUSE

AUDIO OUT

AUDIO IN

L-AUDIO-R

S VIDEO VIDEO

INPUT A MOUSE

AUDIO OUT

AUDIO IN

L-AUDIO-R

Right side

15k RGB/Component equipment

to RGB/component output

SMF-402 Signal Cable (not supplied)

3X phono jack ˜ HD D-sub

15-pin (male)

Connecting with a VCR/15k RGB/Component Equipment

This section describes how to connect the projector with a VCR, external

active speakers, and 15k RGB/component equipment.

For details on how to connect a computer, see page 18 (GB).

Also refer to the instruction manuals of the equipment to be connected.

When making connections, be sure to:

•turn off all equipment before making any connections.

•use the proper cables for each connection.

•insert the plugs of the cables properly; plugs that are not fully inserted

often generate noise. When pulling out a cable, be sure to pull it out from

the plug, not the cable itself.

S-Video cable

(not supplied)

Audio/video cable

(supplied)

Active speakers

to audio/video outputs

1)

to S video

output

1)

VCR

Right side

Connecting

1) When both the S VIDEO and VIDEO jacks are connected to the external equipment, the input signal from the S VIDEO jack is selected.

Stereo audio

connecting cable

(not supplied)

La page charge ...

Sony VPL-SC60U Manuel utilisateur

Ce manuel convient également à

Sony VPL-SC60U Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents