Maytag Bravos MVWB950Y Mode d'emploi

Bravos MVWB950Y
Maytag
Marque
Maytag
Modèle
Bravos MVWB950Y
Catégorie
Machines à laver
Taper
Mode d'emploi

Ce manuel convient également à

W10399633B
W10399634B - SP
Designed to use only HE High Efciency
detergents.
Conçue pour l’utilisation d’un détergent haute
efcacité seulement.
BRAVOS XL
®
TOP-LOADING
HIGH EFFICIENCY
LOW-WATER WASHER
USE AND CARE GUIDE
Table of Contents
WASHER SAFETY .........................................................2
WHAT’S NEW UNDER THE LID? .................................3
CONTROL PANEL AND FEATURES ............................4
Dispensers .......................................................................6
CYCLE GUIDE ............................................................... 6
USING YOUR WASHER ................................................9
WASHER MAINTENANCE .............................................. 13
TROUBLESHOOTING ...................................................... 15
ACCESSORIES .................................................................. 20
WARRANTY........................................................................ 21
ASSISTANCE OR SERVICE ...........................Back Cover
Table des matières
SÉCURITÉ DE LA LAVEUSE ......................................22
QUOI DE NEUF SOUS LE COUVERCLE? ................23
TABLEAU DE COMMANDE
ET CARACTÉRISTIQUES ..........................................24
Distributeurs ..................................................................26
GUIDE DES PROGRAMMES ......................................27
UTILISATION DE LA LAVEUSE ..................................31
ENTRETIEN DE LA LAVEUSE ........................................ 35
DÉPANNAGE ...................................................................... 37
ACCESSOIRES .................................................................. 44
GARANTIE .......................................................................... 47
ASSISTANCE OU SERVICE ..............Couverture arrière
LAVEUSE HAUTE
EFFICACITÉ BRAVOS XL
®
À FAIBLE CONSOMMATION
D’EAU AVEC CHARGEMENT
PAR LE DESSUS GUIDE
D’UTILISATION
ET D’ENTRETIEN
Para una version en espanol, visite www.maytag.com
Certied to Sanitize
Homologué pour assainir
2
WASHER SAFETY
3
Load garments in loose heaps evenly around the washplate.
Do not load garments directly over the center of the washplate;
when loaded, the center of the washplate should be visible.
As the washer dampens and moves the load, the level of the
garments will settle in the basket. This is normal, and does not
indicate that more garments should be added.
IMPORTANT: You will not see a washer basket full of water
as with your past agitator-style washer. It is normal for some
of the load to be above the water line.
WHAT’S NEW UNDER THE LID?
Choosing the Right Detergent
Use only High Efciency detergents. The package will be
marked “HE” or “High Efciency.” Low-water washing creates
excessive sudsing with a regular non-HE detergent. Using
regular detergent will likely result in longer cycle times and
reduced rinsing performance. It may also result in component
failures and noticeable mold or mildew. HE detergents are made
to produce the right amount of suds for the best performance.
Follow the manufacturer’s instructions to determine the amount
of detergent to use.
Normal Sounds You Can Expect
At different stages of the wash cycle, you may hear sounds and
noises that are different from those of your previous washer.
For example, you may hear a clicking and hum at the beginning
of the cycle, as the lid lock goes through a self-test. There
will be different kinds of humming and whirring sounds as the
washplate moves the load. And sometimes, you may hear
nothing at all, as the washer determines the correct water level
for your load or allows time for garments to soak.
Use only High Efciency (HE) detergent.
Concentrated Cleaning
Low-water cleaning means concentrated cleaning. Rather
than diluting detergent as done in an agitator-style washer,
this washer delivers the detergent directly to the soils.
Cleaning with Less Water
The most striking difference in your new washer is the low-water
washplate wash system. The washer automatically adjusts the
water level to the load size—no water level selector is needed.
Traditional agitator-style
washer
Low-water washer
Washplate
Auto Temperature Control (ATC) regulates incoming hot
and cold water, blending the temperatures for optimal and
consistent cleaning. The ATC is automatically turned on when
a cycle is selected.
Auto Temperature Control
INTELLIFILL
™
Water Level Control
Once you start the cycle, the lid will lock, and the washer will
begin the sensing process to determine the correct water level
for the load. You will nd a step-by-step description in the
“Cycle Status Lights” section.
You will hear the motor turn the basket in short pulses to
thoroughly wet the load. This low-water wash method uses
less water and energy compared to a traditional agitator-style
washer.
Washplate
4
CONTROL PANEL AND FEATURES
ESTIMATED TIME REMAINING DISPLAY
The Estimated Time Remaining display shows the time
required for the cycle to complete. Factors such as load size
and water pressure may affect the time shown in the display.
Tightly packed, unbalanced loads, or excessive suds may
cause the washer to adjust the cycle time, as well.
POWER/CANCEL BUTTON
Press to turn the washer ON or OFF.
WASH CYCLE KNOB
Use the Wash Cycle knob to select available cycles on your
washer. Turn the knob to select a cycle for your laundry load.
See “Cycle Guide” for detailed descriptions of cycles.
START/PAUSE BUTTON
Press to start the selected cycle. Be sure all desired
Modiers and Options have been selected. Press START/
PAUSE once to unlock the lid and add a garment. Press
START/PAUSE again to complete the cycle from where it
was stopped. The lid must be closed for the washer to start.
CYCLE MODIFIERS
Modiers allow you to further customize your cycles and
save energy. Not all cycles, options, and modiers are
available on all models.
WASH TEMP
Select a water temperature based on the type of load
you are washing. Use the warmest wash water suitable
for fabrics. Follow garment label instructions.
All cycles use cold rinses. Cold rinses may help with
wrinkling and save energy.
NOTE: In wash water temperatures colder than 60°F
(15.6°C), detergents do not dissolve well. Soils may be
difcult to remove.
SPIN SPEED
This washer automatically selects the spin speed
based on the cycle selected. The preset speeds
can be changed. Not all spin speeds are available
with all cycles.
• Faster spin speeds mean shorter dry times, but
may increase wrinkling in your load.
• Slower spin speeds mean less wrinkling, but will
leave your load more damp.
1
1
2
3
3
4
SOIL LEVEL
Soil Level (wash time) is preset for each wash cycle. As
you press Soil Level, the cycle time (minutes) will increase
or decrease in the Estimated Time Remaining display
and a different wash time will appear.
For most loads, use the Soil Level that is preset with
the cycle you have chosen. For heavily soiled and sturdy
fabrics, press SOIL LEVEL to select more wash time,
if needed. For lightly soiled and delicate fabrics, press
SOIL LEVEL to select less wash time, if needed. Lower
Soil Level settings will help reduce tangling and wrinkling.
CYCLE OPTIONS
When you select a cycle, its default options will light up. Not
all cycles, options, and modiers are available on all models.
WATER SAVE SPRAY RINSE
Use this option to save water by using a spray rinse
instead of a deep water rinse. This option is the default
setting on some cycles, and selectable on other cycles.
When using fabric softener, always select the FABRIC
SOFTENER button, or select EXTRA RINSE; both of these
options will dispense fabric softener in a deep rinse.
OXI TREAT STAINS
Use this option to boost cleaning performance with
Oxi products. This washer is designed to dispense
laundry boosters such as oxygenated stain treaters and
color-safe bleach at the correct time in the cycle for best
cleaning performance, using the liquid chlorine bleach
dispenser. Do not use laundry boosters and chlorine
bleach in the same cycle.
CLEAN BOOST WITH HEATER
The Clean Boost with Heater option helps to ensure better
soil and stain removal. Clean Boost uses a heater within
the washer to maintain the selected temperature setting
throughout the wash period. This option will add some
additional time to the cycle based on which temperature
is selected. It is a preset cycle setting on the Sanitary and
Power Wash cycles. Clean Boost with Heater may be
selected as an option with other cycles.
4
5
Not all features and cycles are available on all models.
2
6
5
6
7
8
5
EXTRA RINSE
This option can be used to automatically add a second
rinse to most cycles.
FABRIC SOFTENER
This option must be selected if using fabric softener
during a cycle. It ensures that fabric softener is added
at the correct time in the rinse for even distribution.
CYCLE SIGNAL
Use this option to adjust volume of the signal that
sounds at end of cycle. You may select Hi, Low,
or Off (no indicator lit). A louder signal is helpful in
removing items as soon as cycle is complete.
You may also add or remove options for each cycle. Not
all options can be used with all cycles, and some are preset
to work with certain cycles.
LID LOCK INDICATOR
This light indicates that the lid is locked and
cannot be opened. If you need to open the lid,
press START/PAUSE. The lid will unlock once
the washer movement has stopped. This may
take several minutes if the load was spinning
at high speed. Press START/PAUSE again
to restart the cycle.
CYCLE STATUS LIGHT INDICATORS
The Cycle Status Lights show the progress of a cycle. At
each stage of the process, you may notice sounds or pauses
that are different from traditional washers.
DELAY
This indicator will light if you use the + or - buttons
to delay the start of your cycle. To use this feature, see
“Select Cycle” in the “Starting Your Washer” section.
FILL
When the Start/Pause button is pressed, the washer will
add a small amount of water to the load, then pause for
a few seconds. The lid will then lock and the washer will
continue to ll.
7
8
WASH
You will hear the motor and washplate moving the load.
It is normal for some of the load to be above the water
line. Low-water cleaning means concentrated cleaning.
Rather than diluting detergent as done in an agitator-style
washer, this washer delivers the detergent directly to the
soils. The motor sounds may change at different stages
in the cycle. The wash time is determined by the selected
Soil Level.
RINSE
You will hear sounds similar to the wash cycle as the
washer rinses and moves the load. You may hear the
motor turning on briey to move the basket while lling.
Fabric softener will be added if the Fabric Softener
option was selected. Some cycles use spray rinsing.
SPIN
The washer spins the load at increasing speeds for
proper water removal, based on the selected cycle
and spin speed.
DONE
Once the cycle is complete, this light will come on.
Remove the load promptly for best results.
HEATING
This light may come on during the wash portion of the
cycle, as the washer slowly spins the load while adjusting
the water temperature.
ADD A GARMENT
You may place additional clothing in the wash when the
Add a Garment indicator is lit without sacricing wash
performance. Press START/PAUSE once. The Lid Lock
light will turn off. Open the washer lid, add garments,
and close the lid. Press START/PAUSE to restart.
CLEAN WASHER REMINDER
The Clean Washer Reminder indicator lights after 30 wash
cycles without a clean washer cycle. See the “Washer
Care” section to run the clean washer cycle, or you can
press REMINDER RESET button to manually reset clean
washer cycle counter.
6
Dispensers
High Efciency “HE” detergent dispenser
Add liquid or powdered HE detergent product
to this dispenser for your main wash cycle.
Liquid chlorine bleach dispenser
This dispenser holds up to 3/4 cup (180 mL) liquid
chlorine bleach. The bleach will be automatically
diluted and dispensed at the optimum time during
the wash cycle. This dispenser cannot dilute
powdered bleach.
Use the liquid chlorine bleach
dispenser for liquid chlorine bleach, color-safe bleach,
or Oxi product laundry boosters.
If using an Oxi
product, be sure to select the Oxi Treat Stains
button. Do not use Oxi products in the same
cycle as liquid chlorine bleach.
Liquid fabric softener dispenser
Pour measured liquid fabric softener into
the liquid fabric softener dispenser, if desired.
It will dispense automatically at the optimum
time when the Fabric Softener option is selected.
•
Use only liquid fabric softener in this dispenser.
•
Do not overll. Do not dilute. The dispenser holds
3 oz (94 mL), or a capful of fabric softener.
A
B
Use only High Efciency (HE) detergent.
C
A
C
B
•
Fabric softener is dispensed in a deep rinse when the Fabric
Softener option is selected. If Extra Rinse is selected, the fabric
softener will be dispensed during the nal rinse.
•
Do not use fabric softener dispensing balls in this washer.
Dispensing balls will not operate correctly with this washer.
•
Do not spill or drip any fabric softener onto the clothes.
•
At the end of the cycle, a small amount of water may be left
in the dispenser. This is normal.
CYCLE GUIDE
Items to wash: Cycle:
Wash*
Temperature:
Spin
Speed:
Soil
Level:
Available
Options:
Cycle Details:
Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle that best ts the load
being washed. Not all cycles and options are available on all models.
Cottons,
linens, and
mixed garment
loads
Normal Max
Extract
Medium
No Spin
Use this cycle for normally soiled
cottons and mixed fabric loads. This
cycle combines high-speed wash
action and medium-speed spin.
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
Oxi Treat Stains
Normally
soiled sheets,
pillowcases,
light blankets,
or throws
Sheets
Max
Extract
Medium
Low
No Spin
The wash action of this cycle is
designed to keep large garments from
tangling and balling up.
IMPORTANT: For best performance,
load garments in loose heaps evenly
around the washplate. Do not load
garments directly over the center of
the washplate.
Clean Boost
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
Oxi Treat Stains
Hot
Warm
Cool
Cold
Eco Cold
Hot
Warm
Cool
Cold
Eco Cold
Extra Heavy
Heavy
Medium
Light
Extra Heavy
Heavy
Medium
Light
Sturdy fabrics,
dark colors that
bleed or fade
Cold Wash Use this cycle for sturdy garments with
dark or bright colors that could bleed
or fade in a warmer wash cycle. This
cycle is a good choice for washing new
garments that may shrink or fade
in their rst wash.
Cold
Eco Cold
Max
Extract
Medium
Low
No Spin
Extra Heavy
Heavy
Medium
Light
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
Oxi Treat Stains
* Wash temperatures vary according to the chosen cycle setting. All cycle settings use a cold rinse temperature.
7
CYCLE GUIDE
Items to wash: Cycle:
Wash*
Temperature:
Spin
Speed:
Soil
Level:
Available
Options:
Cycle Details:
Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle that best ts the load
being washed. Not all cycles and options are available on all models.
Towels
and terrycloth
garments,
lightly soiled,
colored clothing
Colors/
Towels
Hot
Warm
Cool
Cold
Eco Cold
Max
Extract
Medium
Low
No Spin
Extra Heavy
Heavy
Medium
Light
This cycle is also a good choice for
garments with a wrinkle-free nish. This
cycle uses medium-speed wash action
and medium-speed spin.
Clean Boost
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
Oxi Treat Stains
Performance and
athletic wear
Active
Wear
This cycle uses extra water for wash
and an Extra Rinse for thorough
cleaning. Oxi dispense is defaulted
on this cycle, but may be deselected
if not needed.
Lightly soiled
garments
Rapid
Wash
Hot
Warm
Cool
Cold
Eco Cold
Max
Extract
Medium
Low
No Spin
Extra Heavy
Heavy
Medium
Light
Use this cycle to wash small, lightly
soiled loads that are needed in a hurry.
This short cycle combines high-speed
wash action and high-speed spin for
the optimal cleaning and shortened dry
times.
Clean Boost
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
Oxi Treat Stains
Machine-wash
silks, hand-wash
fabrics and wool
Delicate
(Handwash)
Hot
Warm
Cool
Cold
Eco Cold
Medium
Low
No Spin
This cycle combines low-speed wash
and low-speed spin action to clean
garments labeled as “Machine
Washable” on the garment care label.
Clean Boost
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
Oxi Treat Stains
Extra Heavy
Heavy
Medium
Light
* Wash temperatures vary according to the chosen cycle setting. All cycle settings use a cold rinse temperature.
Large items
such as sleeping
bags, blankets,
small comforters,
and jackets
Bulky Medium
Low
No Spin
Extra Heavy
Heavy
Medium
Light
This cycle starts with a soak to
thoroughly saturate your large load.
This is followed by medium wash action
and medium spin speeds to maintain
load balance.
IMPORTANT: When washing
waterproof/water-resistant items such
as plastic lined mattress pads, shower
curtains, tarps, jackets, or sleeping
bags, select the lowest spin speed
setting available for the cycle and
washer model being used.
Clean Boost
Extra Rinse
Fabric Softener
Oxi Treat Stains
Hot
Warm
Cool
Cold
Eco Cold
Sturdy fabrics,
colorfast
garments
Heavy
Duty
Max
Extract
Medium
Low
No Spin
Extra Heavy
Heavy
Medium
Light
Clean Boost
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
Oxi Treat Stains
Use this cycle for heavily soiled or
sturdy cotton garments. Cycle combines
high-speed wash action and high-speed
spin.
Hot
Warm
Cool
Cold
Eco Cold
Hot
Warm
Cool
Cold
Eco Cold
Max
Extract
Medium
Low
No Spin
Extra Heavy
Heavy
Medium
Light
Clean Boost
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
Oxi Treat Stains
Heavily soiled
white fabrics
Whites Max
Extract
Medium
Low
No Spin
This cycle introduces liquid chlorine
bleach to the load at the proper time
for improved whitening of your heavily
soiled white fabrics. This cycle combines
high-speed wash action and high-speed
spin speed. For maximum soil and stain
removal, use the liquid chlorine bleach
dispenser for liquid chlorine bleach,
color-safe bleach, or Oxi product laundry
boosters. This cycle can also be used
for sturdy color fabrics, such as towels
without liquid chlorine bleach.
Clean Boost
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
Oxi Treat Stains
Hot
Warm
Cool
Cold
Eco Cold
Extra Heavy
Heavy
Medium
Light
Heavily soiled
fabrics
Power
Wash
Hot
Warm
Cool
Cold
Eco Cold
Max
Extract
Medium
Low
No Spin
Extra Heavy
Heavy
Medium
Light
Use this cycle for extremely soiled
garments and household items that
need additional cleaning power. This
cycle combines high-speed wash action,
medium-speed spin, and a deep rinse
to ush excess dirt from the load.
Clean Boost
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
Oxi Treat Stains
8
CYCLE GUIDE
Items to wash:
Wash*
Temperature:
Spin
Speed:
Soil
Level:
Available
Options:
Cycle Details:
No garments
in washer
Heavily soiled
fabrics
Clean
Washer
with
affresh
®
Soak Warm
Cool
Cold
Eco Cold
Extra Heavy
Heavy
Medium
Light
Use this cycle every 30 washes to keep the
inside of your washer fresh and clean. This
cycle uses a higher water level. Use with
affresh
®
Washer Cleaner tablet or liquid
chlorine bleach to thoroughly clean the
inside of your washer. This cycle should not
be interrupted. See “Washer Care.”
IMPORTANT: Do not place garments or
other items in the washer during the Clean
Washer with affresh
®
cycle. Use this cycle
with an empty wash tub.
Adjust the Soil Level to change soak time
according to your needs. After the selected
soak period has ended, the washer will
drain but does not spin the load. After
draining, the washer will pause until a wash
cycle is selected, to complete the cleaning
process.
NOTE: Automatic bleach dispensing is not
part of the soak cycle.
Swimsuits,
garments that
need rinsing
only
Rinse/Drain
& Spin
Use Rinse/Drain & Spin with the Extra
Rinse option turned on to get a deep rinse
followed by a high-speed spin. The time
display will include an estimate of how long
it will take to ll and drain the washer.
Cycle:
Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle that best ts the load
being washed. Not all cycles and options are available on all models.
Max
Extract
Medium
Low
No Spin
* Wash temperatures vary according to the chosen cycle setting. All cycle settings use a cold rinse temperature.
Cottons and
linens exposed
to possible
allergens
Allergen
This cycle uses more water to ush out
allergens, such as dust mites or pet dander,
from normally soiled garments. This cycle
removes more than 95% of allergens.
Clean Boost
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
Oxi Treat Stains
Heavily soiled,
colorfast fabrics
Sanitary
with Oxi
†
Hot
Max
Extract
Medium
Low
No Spin
Extra Heavy
Heavy
Medium
Light
Use this cycle to eliminate 99.9%
of bacteria when used in conjunction with
the Clean Boost with Heater option. Preset
cycle setting must be used to achieve
the proper sanitization. Be sure to add an
Oxi product to the Liquid Chlorine Bleach
dispenser.
Hot
† Sanitary with Oxi
Sanitary with Oxi cycle certied by NSF International, an independent, third party testing and certication organization. The
certication veried that the cycle reduced 99.9% of bacteria typically found in clothing, bedding, and towels. There is no carry
over of bacteria between loads after the cycle is complete. Only the Sanitary with Oxi cycle has been designed to meet the
requirements of NSF Protocol P12 for Sanitizing Effectiveness.
Use Rinse/Drain & Spin to remove excess
water from the load by choosing Rinse/
Drain & Spin and turning off Extra Rinse.
This cycle may help shorten drying times
for some heavy fabrics or special-care
garments. Spin speed can be set to
a lower setting.
Rinse/Drain & Spin may also be used for
draining the washer after canceling a cycle
or completing a cycle after a power failure.
Rinse/Drain
& Spin
Wet load
of garments
Max
Extract
Medium
Low
No Spin
Extra Heavy
Heavy
Medium
Light
Clean Boost
Extra Rinse
Fabric Softener
Oxi Treat Stains
Model: MVWB950Y**
Max
Extract
Medium
Low
Extra Rinse
9
USING YOUR WASHER
• Empty pockets. Loose change, buttons, or any small object
can pass under the washplate and become trapped, causing
unexpected sounds.
• Sort garments by recommended cycle, water temperature,
and colorfastness.
• Separate heavily soiled garments from lightly soiled.
• Separate delicate garments from sturdy fabrics.
• Do not dry garments if stains remain after washing; heat can
set stains into fabric.
• Treat stains promptly.
• Close zippers, fasten hooks, tie strings and sashes.
Remove non-washable trim and ornaments.
• Mend rips and tears to avoid further damage to garments
during washing.
Helpful Tips:
• When washing water-proof or water-resistant items, load
evenly. See “Cycle Guide” for tips and more information on
using the Bulky cycle.
• Use mesh bags to help avoid tangling when washing delicate
or small items.
• Turn knits inside out to avoid pilling. Separate lint-takers from
lint-givers. Synthetics, knits, and corduroy fabrics will pick up
lint from towels, rugs, and chenille fabrics.
NOTE: Always read and follow fabric care labels instructions
to avoid damage to your garments.
1. Sort and prepare your laundry
Load garments in loose heaps evenly
around the washplate. Do not load
garments directly over the center
of the washplate; when loaded, the
center of the washplate should be visible. Try mixing different
sized garments to reduce tangling.
IMPORTANT: Garments need to move freely for best cleaning
and to reduce wrinkling and tangling.
3. Load laundry into washer
Single-dose laundry packet or fabric softener crystals can be
added to the basket prior to adding laundry.
NOTE: Do not add clothes to washer basket prior to adding
laundry products. Always follow manufacturer’s instructions.
2. Add single-dose laundry packet or
fabric softener crystals (if desired)
10
Add a measured amount of HE
detergent into detergent dispenser.
IMPORTANT: Use only High Efciency detergents. The package
will be marked “HE” or “High Efciency.” Low-water washing
creates excessive sudsing with a regular non-HE detergent.
Using regular detergent will likely result in longer cycle times and
reduced rinsing performance. It may also result in component
failures and noticeable mold or mildew. HE detergents are made
to produce the right amount of suds for the best performance.
Follow the manufacturer’s instructions to determine the amount
of detergent to use.
HELPFUL TIP: See “Washer Maintenance” for information
on recommended method of cleaning washer dispensers.
4. Add HE detergent to dispenser
6. Add liquid fabric softener to
dispenser
Pour a measured amount of liquid
fabric softener into dispenser; always
follow manufacturer’s directions for correct amount
of fabric softener based on your load size. Then select
Fabric Softener option.
IMPORTANT: Fabric Softener option must be selected
to ensure proper distribution at correct time in cycle.
Do not overll or dilute. Overlling dispenser will cause
fabric softener to immediately dispense into washer.
If Extra Rinse option is selected, fabric softener will be
dispensed in the last rinse.
NOTE: Do not use liquid fabric softener dispenser balls
in this washer. They will not dispense correctly.
7. Press POWER/CANCEL to turn on
washer
Detergent dispenser
Fabric softener dispenser
5. Add liquid chlorine bleach
or Oxi product to dispenser
Do not overll, dilute, or use more than 3/4 cup (180 mL).
Do not use color-safe bleach or Oxi products in the same
cycle with liquid chlorine bleach. For maximum soil and stain
removal, you may use the liquid chlorine bleach dispenser for
liquid chlorine bleach, color-safe bleach, or Oxi product laundry
boosters.
IMPORTANT: If using an Oxi product,
be sure to select the Oxi Treat Stains
button. Use the liquid chlorine bleach
dispenser for Oxi products. Do not
use Oxi products in the same cycle
as liquid chlorine bleach.
Liquid chlorine
bleach dispenser
NOTE: Do not add single-dose laundry packets or fabric softener
crystals to dispensers. They will not dispense correctly.
11
Turn cycle knob to choose your wash
cycle. Estimated Time Remaining
will light up with a cycle time. You may
notice time adjusting during the cycle.
This is normal.
If you do not want to begin a cycle
immediately, you may choose DELAY
START option.
To choose a delay time:
1. Press POWER/CANCEL.
2. Select the desired Cycle, Modiers, and Options. Delay Start
is not valid for Rinse/Drain & Spin cycle.
3. Press + (plus) DELAY START. 1H (one hour) will be displayed
in the time display window. The indicator light for Delay will
glow.
4. For a longer delay time, press DELAY START + (plus). For a
shorter delay time, press DELAY START – (minus). The Start
Time will increase or decrease by 1-hour steps.
5. Press START/PAUSE. The countdown in hours and minutes
to the wash cycle will show in the time display window and
the indicator light will begin to ash.
NOTE: The Start/Pause indicator light will not ash when
Delay Start is chosen. You must press START/PAUSE
to initiate a countdown for the cycle to begin. The cycle
selections and modiers are lit during the Delay Start time.
To cancel delaying a cycle:
Press POWER/CANCEL once to cancel Delay Start or press
START/PAUSE to cancel the countdown and start the cycle.
IMPORTANT: When delaying a cycle, use liquid HE detergent
only in the dispenser. Powdered detergents may absorb
moisture from a previous cycle and clump before the wash
cycle begins.
8. Select cycle 9. Select cycle modiers
Once you select a cycle, the default settings for that cycle will
be lit. Press the Modier buttons to change the Wash Temp,
Spin Speed, and Soil Level, if desired. Not all settings are
available with all cycles.
NOTE: Always read and follow fabric care labels instructions
to avoid damage to your garments.
Wash Temp
Hot
Some cold water is added to save
energy. This may be cooler than
your hot water heater setting.
Warm
Some cold water will be added,
so this may be cooler than what
your previous washer provided.
Cool
Warm water is added to assist
in soil removal and to help
dissolve detergents.
Cold
Warm water may be added
to assist in soil removal and
to help dissolve detergents.
Eco Cold
This is the temperature from
your faucet.
Suggested Fabrics
Whites and pastels
Durable garments
Heavy soils
Bright colors
Moderate to light soils
Colors that bleed
or fade
Light soils
Dark colors that
bleed or fade
Light soils
Dark colors that
bleed or fade
Light soils
12
11. Press START/PAUSE to begin
wash cycle
Press the START/PAUSE button to start the wash cycle. When
the cycle has nished, the end of cycle signal will sound (if set).
Promptly remove garments when cycle is done to avoid odor,
reduce wrinkling, and rusting of metal hooks, zippers, and snaps.
If lid is left open for more than 10 minutes the water will
pump out.
10. Select cycle options
Select any other cycle options you may wish to add, if not
previously set. Some cycles will automatically add certain
options such as Clean Boost. These may be turned off,
if desired.
NOTE: Not all options are available with all cycles.
13
WASHER MAINTENANCE
Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Periodically inspect and replace inlet hoses
if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of
replacement on the label with a permanent marker.
NOTE: This washer does not include inlet hoses. See
the Installation Instructions for more information.
WATER INLET HOSES
WASHER CARE
Recommendations to Help Keep Your Washer Clean
and Performing at its Best
1. Always use High Efciency (HE) detergents and follow the
HE detergent manufacturer’s instructions regarding the
amount of HE detergent to use. Never use more than the
recommended amount because that may increase the
rate at which detergent and soil residue accumulate inside
your washer, which in turn may result in undesirable odor.
2. Use warm and hot wash water settings sometimes (not
exclusively cold water washes), because they do a better
job of controlling the rate at which soils and detergent
accumulate.
3. Always leave the washer lid open between uses to help
dry out the washer and prevent the buildup of odor-
causing residue.
Cleaning Your Top Loading Washer
Read these instructions completely before beginning the
routine cleaning processes recommended below. This
Washer Maintenance Procedure should be performed,
at a minimum, once per month or every 30 wash cycles,
whichever occurs sooner, to control the rate at which soils
and detergent may otherwise accumulate in your washer.
Cleaning the Inside of the Washer
To keep your washer odor-free, follow the usage instructions
provided above, and use this recommended monthly
cleaning procedure:
Clean Washer Cycle
This washer has a special cycle that uses higher water
volumes in combination with affresh
®
Washer Cleaner
or liquid chlorine bleach to clean the inside of the washer.
Begin procedure
1. affresh
®
Washer Cleaner Cycle Procedure
(Recommended for Best Performance):
a. Open the washer lid and remove any clothing or items.
b. Place an affresh
®
Washer Cleaner tablet in the bottom
of the washer basket.
c. Do not place an affresh
®
Washer Cleaner tablet
in the detergent dispenser.
d. Do not add any detergent or other chemical to the
washer when following this procedure.
e. Close the washer lid.
f. Select the CLEAN WASHER cycle.
g. Press the START/PAUSE button to begin the cycle.
The Clean Washer Cycle Operation is described below.
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, press POWER/CANCEL. (For models
with no Power/Cancel button, press and hold START/
PAUSE for three seconds). After the Clean Washer cycle
has stopped, run a
Rinse/Drain & Spin
cycle to rinse
cleaner from washer.
WASHER CARE (cont.)
2. Chlorine Bleach Procedure (Alternative):
a. Open the washer lid and remove any clothing
or items.
b. Add 1 cup (236 mL) of liquid chlorine bleach
to the bleach compartment.
NOTE: Use of more liquid chlorine bleach than is
recommended above could cause washer damage
over time.
c. Close the washer lid.
d. Do not add any detergent or other chemical
to the washer when following this procedure.
e. Select the CLEAN WASHER cycle.
f. Press the START/PAUSE button to begin the cycle. The
Clean Washer Cycle Operation is described below.
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, press POWER/CANCEL. (For models
with no Power/Cancel button, press and hold START/
PAUSE for three seconds). After the Clean Washer cycle
has stopped, run a
Rinse/Drain & Spin
cycle to rinse
cleaner from washer.
Description of Clean Washer Cycle Operation:
1. This cycle will ll to a water level higher than in normal
wash cycles to provide rinsing at a level above the water
line for normal wash cycle.
2. During this cycle, there will be some agitation and
spinning to increase the removal of soils.
After this cycle is complete, leave the lid open to allow
for better ventilation and drying of the washer interior.
Cleaning the Dispensers
After a period of using your washer, you may nd some
residue buildup in the washer’s dispensers. To remove
residue from the dispensers, wipe them with a damp cloth
and towel dry. Do not attempt to remove the dispensers or
trim for cleaning. The dispensers and trim are not removable.
If your model has a dispenser drawer, however, remove the
drawer and clean it before or after you run the Clean Washer
cycle. Use an all-purpose surface cleaner, if needed.
Cleaning the Outside of the Washer
Use a soft, damp cloth or sponge to wipe away any spills.
Use only mild soaps or cleaners when cleaning external
washer surfaces.
IMPORTANT: To avoid damaging the washer’s nish, do not
use abrasive products.
14
Operate your washer only when you are home. If moving,
or not using your washer for a period of time, follow these
steps:
1. Unplug or disconnect power to washer.
2. Turn off water supply to washer, to avoid ooding
due to water pressure surge.
WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1. Shut off both water faucets; disconnect and drain water
inlet hoses.
2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket
and run washer on RINSE/DRAIN & SPIN cycle for about
30 seconds to mix antifreeze and remaining water.
3. Unplug washer or disconnect power.
NON-USE AND VACATION CARE
REINSTALLING/USING WASHER AGAIN
To reinstall washer after non-use, vacation, winter storage
or moving:
1. Refer to Installation Instructions to locate, level, and
connect washer.
2. Before using again, run washer through the following
recommended procedure:
To use washer again:
1. Flush water pipes and hoses. Reconnect water inlet
hoses. Turn on both water faucets.
2. Plug in washer or reconnect power.
3. Run washer through BULKY cycle to clean washer and
remove antifreeze, if used. Use only HE High Efciency
detergent. Use half the manufacturer’s recommended
amount for a medium-size load.
TRANSPORTING YOUR WASHER
1. Shut off both water faucets. Disconnect and drain water
inlet hoses.
2. If washer will be moved during freezing weather, follow
WINTER STORAGE CARE directions before moving.
3. Disconnect drain from drain system.
4. Unplug power cord.
5. Place inlet hoses inside washer basket.
6. Drape power cord and drain hose over the console
and secure with masking tape.
7. Place foam packing ring from original shipping materials
back inside washer. If you do not have packing ring,
place heavy blankets or towels into basket opening.
Close lid and place tape over lid and down front of
washer. Keep lid taped until washer is placed in
new location.
15
First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.
In U.S.A. www.maytag.com/help – In Canada www.maytag.ca.
If you experience
Possible Causes
Solution
Feet may not be in contact with the
oor and locked.
Front and rear feet must be in rm contact with oor, and
washer must be level to operate properly. Jam nuts must be
tight against the bottom of the cabinet.
Check oor for exing or sagging. If ooring is uneven, a 3/4"
(19 mm) piece of plywood under your washer will reduce sound.
See “Level Washer” in the Installation Instructions.
Load could be unbalanced.
Load garments in loose heaps evenly around the washplate.
Do not load garments directly over the center of the washplate.
Adding wet items to washer or adding more water to basket
could unbalance washer.
Avoid washing single items. Balance a single item such
as a rug or jacket with a few extra items. If the uL error code
is ashing, redistribute the load, close the lid, and press
START/PAUSE.
Use Bulky cycle for oversized, non-absorbent items such
as comforters or poly-lled jackets. Other items are not
appropriate for Bulky cycle. See “Cycle Guide.”
Item or load not suitable for selected cycle. See “Cycle Guide”
and “Using Your Washer.”
Empty pockets before washing. Loose items such as coins
could fall between basket and tub or may block pump.
It may be necessary to call for service to remove items.
Washer not level.
Water may splash off basket if washer is not level.
Fill hoses not attached tightly.
Tighten ll-hose connection.
Make sure all four ll hose at washers are properly seated.
Drain hose connection
Pull drain hose from washer cabinet and properly secure it to
drainpipe or laundry tub.
Check household plumbing for leaks
or clogged sink or drain.
Water can back up out of a clogged sink or drainpipe. Check
all household plumbing for leaks (laundry tubs, drain pipe,
water pipes, and faucets.)
Fill hose washers
Noises – For normal operating sounds, go to www.maytag.com/help.
It is normal to hear metal items on clothing such as metal snaps,
buckles, or zippers touch against the stainless steel basket.
Objects caught in washer
drain system.
Clicking or metallic
noises
Gurgling or humming
It is normal to hear the pump making a continuous humming
sound with periodic gurgling or surging as nal amounts of
water are removed during the spin/drain cycles.
Washer may be draining water.
Water Leaks
Check the following for
proper installation:
Do not place tape over drain opening.
An unbalanced load can cause basket to be out of alignment
and cause water to splash off tub. See “Using Your Washer”
for loading instructions.
Washer not loaded as
recommended.
TROUBLESHOOTING
Vibration, rocking, or
“walking”
Not enough water
in washer
Load not completely covered
in water.
This is normal operation for an HE low-water washer. The load
will not be completely under water. The washer senses load
sizes and adds correct amount of water for optimal cleaning.
See “What’s New under the Lid.”
IMPORTANT: Do not add more water to washer. The added
water lifts the load off the washplate, resulting in less effective
cleaning.
Washer not performing as expected
Washer may not be level.
Vibration or Off-Balance
Vibration during spinning
or washer stopped with
uL error code ashing
16
If you experience
Possible Causes
Solution
Normal washer operation.
Lid must be closed for washer to run.
Washer will pause during certain phases of cycle.
Do not interrupt cycle.
Washer may be stopped to reduce suds.
Washer won’t run
or ll, washer stops
working (cont.)
Plug power cord into a grounded 3-prong outlet.
Do not use an extension cord.
Ensure there is power to outlet.
Reset a tripped circuit breaker. Replace any blown fuses.
NOTE: If problems continue, contact an electrician.
Check proper electrical supply.
Washer may be tightly packed.
Remove several items, rearrange load evenly around the
washplate. Do not load garments directly over the center
of the washplate. Close lid and press START/PAUSE.
Add only 1 or 2 additional garments after washer has started.
Not using HE detergent or using too
much HE detergent.
Only use HE detergent. Suds from regular detergents can slow
or stop the washer. Always measure detergent and following
detergent directions based on your load requirements.
To remove suds, cancel cycle. Select RINSE/DRAIN & SPIN.
Select your cycle. Press START/PAUSE. Do not add more
detergent.
Small items may have been caught in pump or between basket
and tub, which can slow draining.
Empty pockets and use garment
bags for small items.
Washer not draining/
spinning, loads are
still wet
Washer not performing as expected (cont.)
TROUBLESHOOTING
Do not add more water to the washer.
If you experience
Possible Causes
Solution
Washer not performing as expected (cont.)
Washer won’t run or ll,
washer stops working
Check for proper water supply.
Both hoses must be attached and have water owing to
inlet valve.
Both hot and cold water faucets must be turned on.
Check that inlet valve screens have not become clogged.
Check for any kinks in inlet hoses, which can restrict water ow.
First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.
In U.S.A. www.maytag.com/help – In Canada www.maytag.ca.
17
Check plumbing for correct drain
hose installation. Drain hose extends
into standpipe farther than 4.5"
(114 mm).
Check drain hose for proper installation. Use drain hose form
and securely attach to drainpipe or tub. Do not tape over drain
opening. Lower drain hose if the end is higher than 96" (2.4 m)
above the oor. Remove any clogs from drain hose.
Not using HE detergent or using too
much HE detergent.
Suds from regular detergent or using too much detergent
can slow or stop draining or spinning. Use only HE detergent.
Always measure and follow detergent directions for your
load. To remove extra suds, select RINSE/DRAIN & SPIN.
Do not add detergent.
Load is tangling
Washer not loaded as recommended.
Load garments in loose heaps evenly around the washplate.
Do not load garments directly over the center of the washplate.
Reduce tangling by mixing types of load items. Use the
recommended cycle for the type of garments being washed.
If you experience
Possible causes
Solution
Incorrect or wrong
wash or rinse
temperatures
Check for proper water supply.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached to both washer and faucet,
and have both hot and cold water owing to inlet valve.
Check that inlet valve screens are not clogged.
Remove any kinks in hoses.
Energy Star
®
qualied washers use cooler wash and rinse water
temperatures than traditional top-load washers. This includes
cooler hot and warm washes.
Load not rinsed
Check for proper water supply.
Washer not performing as expected (cont.)
TROUBLESHOOTING
Energy-saving controlled wash
temperatures.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached and have water owing to the
inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
Not using HE detergent or using too
much HE detergent.
The suds from regular detergent can cause the washer
to operate incorrectly.
Use only HE detergent. Be sure to measure correctly.
Always measure detergent and follow detergent directions
based on load size and soil level.
Washer may be tightly packed.
The washer is less efcient at rinsing when load is tightly
packed.
Load garments in loose heaps evenly around the washplate.
Do not load garments directly over the center of the washplate.
Use cycle designed for the fabrics being washed.
Add only 1 or 2 additional garments after washer has started.
Fabric softener option not selected.
When using fabric softener, be sure the Fabric Softener option
is selected.
Sand, pet hair, lint, etc.
on load after washing
Heavy sand, pet hair, lint, and
detergent or bleach residues
may require additional rinsing.
Add an Extra Rinse to the selected cycle.
Washer not draining/
spinning, loads are
still wet (cont.)
Washer may be tightly packed or
unbalanced.
Tightly packed loads may not allow the washer to spin correctly,
leaving the load wetter than normal. Evenly arrange the wet
load for balanced spinning. Select RINSE/DRAIN & SPIN
to remove excess water. See “Using Your Washer” for loading
recommendations.
Using cycles with a lower spin speed.
Cycles with lower spin speeds remove less water than cycles
with high spin speeds. Use the recommended cycle/speed spin
for your garment.
First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.
In U.S.A. www.maytag.com/help – In Canada www.maytag.ca.
18
If you experience
Possible Causes
Solution
TROUBLESHOOTING
Not using HE detergent or using too
much HE detergent.
Not using correct cycle for fabric type.
Not using dispensers.
Not washing like colors together.
The suds from regular detergent can prevent washer from
operating correctly.
Use only HE detergent. Be sure to measure correctly.
Always measure detergent and follow detergent directions
based on load size and soil level.
Use a higher soil level cycle option and warmer wash
temperature to improve cleaning.
If using Rapid Wash cycle, wash only a few items.
Use Power Wash, Whites, or Heavy Duty cycle for tough
cleaning.
See the “Cycle Guide” to match your load with the best cycle.
Use dispensers to avoid chlorine bleach and fabric softener
staining.
Load dispensers before starting a cycle.
Avoid overlling.
Do not add products directly onto load.
Wash like colors together and remove promptly after the cycle
is complete to avoid dye transfer.
Washer not performing as expected (cont.)
Clean washer maintenance not done
as recommended.
Not using HE detergent or using too
much HE detergent.
Run the Clean Washer with affresh
®
cycle after every
30 washes. See “Washer Care” in “Washer Maintenance.”
Unload washer as soon as cycle is complete.
Use only HE detergent. Be sure to measure correctly.
Always follow the detergent directions.
See “Washer Care” section.
Odors
Empty pockets, zip zippers, and snap or hook fasteners before
washing to avoid snags and tears.
Sharp items were in pockets during
wash cycle.
Strings and straps could have tangled.
Items may have been damaged before
washing.
Mend rips and broken threads in seams before washing.
Fabric damage can occur if the
washer is tightly packed.
Load garments in loose heaps evenly around the washplate.
Do not load garments directly over the center of the washplate.
Use cycle designed for the fabrics being washed.
Add only 1 or 2 additional garments after washer has started.
Tie all strings and straps before starting wash load.
Fabric Damage
Garment care instructions may not
have been followed.
Always read and follow garment manufacturer’s care label
instructions. See the “Cycle Guide” to match your load with
the best cycle.
Washer not loaded as recommended.
This is normal operation for an HE low-water washer. The load
will not be completely under water. The washer senses load
sizes and adds correct amount of water for optimal cleaning.
See “What’s New under the Lid.”
Do not add additional water to washer. Additional water lifts the
laundry off the washplate, resulting in less effective cleaning.
Load garments in loose heaps evenly around the washplate.
Do not load garments directly over the center of the washplate.
Add only 1 or 2 additional garments after washer has started.
Not cleaning or
removing stains
Load not completely covered in water.
Added more water to washer.
Wash action and/or spin speed too
fast for load.
Select a cycle with a slower wash action and slower spin speed.
Note that items will be wetter than when using a higher speed spin.
Load is tangling (cont.)
First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.
In U.S.A. www.maytag.com/help – In Canada www.maytag.ca.
19
You may only place Oxi products directly in the liquid chlorine
bleach dispener. If using Oxi products, be sure to select OXI
TREAT STAINS option. Do not use both liquid chlorine bleach
and Oxi product in the same load.
Liquid chlorine bleach may have been
added incorrectly.
Do not pour liquid chlorine bleach directly onto load. Wipe up
bleach spills.
Undiluted bleach will damage fabrics. Do not use more than
recommended by manufacturer.
Do not place load items on top of bleach dispenser when
loading and unloading washer.
If you experience
Possible Causes
Solution
Clogged dispensers or laundry
products dispensing too soon.
Do not overll dispenser. Overlling causes immediate
dispensing.
Always select FABRIC SOFTENER and/or OXI TREAT STAINS
options to ensure proper dispensing.
Load dispensers before starting a cycle.
It is normal for small amounts of water to be remain in dispenser
at the end of the cycle.
Homes with low water pressure may result in residual powder
in the dispenser. To avoid, select a warmer wash temperature
if possible, depending on your load.
Use liquid chlorine bleach only in the liquid chlorine bleach
dispenser.
Incorrect dispenser
operation
TROUBLESHOOTING
Washer not performing as expected (cont.)
Error Code Appears in Display
oL (overloaded)
appears in display
Load too large.
If an overload is detected, the washer will drain any water and
detergent in the washer. Remove several items and add HE
detergent. Close lid and press START/PAUSE.
Liquid chlorine bleach not used in
dispenser or Oxi Treat Stains option
not selected.
uL (unbalanced load)
appears in display
Load not balanced. The washer is
running a load-balance correction
routine.
Allow the washer to continue. If the dial is ashing and the
washer has stopped, redistribute the load, close the lid, and
press START/PAUSE.
HC (Hot and Cold
hoses reversed)
appears in display
Hot and cold inlet hoses have been
installed incorrectly.
This code will appear at the end of the wash cycle to indicate
that cold water hose is connected to the hot water inlet and hot
water hose is connected to the cold water inlet.
Sd (Excess suds)
appears in display
Excessive suds in washer. Washer is
running a suds reduction routine.
Allow the washer to continue. Use only HE detergent.
Always measure detergent, and base detergent quantity on
load size. Follow detergent manufacturer’s instructions. If the
dial is ashing, reselect your desired cycle using a cold wash
temperature, and press START/PAUSE. Do not add detergent.
dL (Lid cannot lock)
appears in display
An item in the load may be keeping
the lid from locking.
Check for items directly under the lid.
lid (Lid opened)
appears in display
Washer lid left open.
Close the lid to clear the display. If the lid is left open for more
than 10 minutes, the cycle will reset and water in the washer
will drain.
LF (too long to ll)
appears in display
Washer taking too long to ll.
Drain extends more than
4.5" (114 mm) into standpipe.
Check plumbing for correct drain hose installation. Use drain
hose form and attach securely to drainpipe or tub. Do not tape
over drain opening. See Installation Instructions.
Ld (too long to drain
water ) appears in
display
Washer taking too long to drain
water. Drain extends more than
4.5" (114 mm) into standpipe.
Check plumbing for correct drain hose installation. Use drain
hose form and attach securely to drainpipe or tub. Do not tape
over drain opening. See Installation Instructions.
Lower drain hose if the end is higher than 96" (2.4 m) above
the oor. Remove any clogs from drain hose. See Installation
Instructions.
Fabric Damage (cont.)
First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.
In U.S.A. www.maytag.com/help – In Canada www.maytag.ca.
Using single-dose
laundry packet
Packet not dissolving. Make sure single-dose laundry packet is added to washer
basket before adding clothes. Follow the manufacturer’s
recommendations.
20
Error Code Appears in Display (cont.)
dU (Lid cannot unlock)
appears in display
Objects on washer lid prevent it from
unlocking.
Remove objects, such as a basket of laundry, from the top of
the washer.
F## code (F-type
error code) appears
in display
System error code.
Press START/PAUSE once to clear the code. Then press
START/PAUSE again to restart washer. If code appears again,
call for service.
Fd (Factory Default)
Washer sets back to factory default.
To return all options and modiers to Factory Default, press
POWER/CANCEL, select RINSE/DRAIN & SPIN cycle, and
then press EXTRA RINSE, FABRIC SOFTENER, EXTRA RINSE,
FABRIC SOFTENER within 5 seconds. When done correctly,
the display shows “Fd” for 3 seconds and then unit returns
to Standby Mode.
If you experience
Possible Causes
Solution
TROUBLESHOOTING
ACCESSORIES
Accessory
Part Number:
8212526
31682
1903WH
Washer drip tray, ts under all
All-purpose appliance cleaner
Laundry supply storage cart
See Installation Instructions for installation accessories
First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.
In U.S.A. www.maytag.com/help – In Canada www.maytag.ca.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Maytag Bravos MVWB950Y Mode d'emploi

Bravos MVWB950Y
Maytag
Marque
Maytag
Modèle
Bravos MVWB950Y
Catégorie
Machines à laver
Taper
Mode d'emploi
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents