GE GTS18TCSCC Le manuel du propriétaire

ge.com
Refrigerators
Top-Freezer
02IDD415    197D6599P001     49-60364    05-05 JR
Safety Instructions  . . . . . . . . . . .2–4
Operating Instructions
Additional Features  . . . . . . . . . . . . .9
Automatic Icemaker  . . . . . . . . . . .10
Controls . . . . . . . . . . . . . . . . . . . . . .5
Shelves and Bins  . . . . . . . . . . . . .6, 7
Crispers and Pans  . . . . . . . . . . . .8, 9
Care and Cleaning
Care and Cleaning . . . . . . . . . .11, 12
Replacing the Light Bulbs . . . . . . .12
Installation Instructions
Preparing to Install 
the Refrigerator . . . . . . . . . . . . . . .13
Reversing the Door Swing  . . . .18–21
Water Line Installation  . . . . . .14–17
Troubleshooting Tips . . . . . . .22–25
Normal Operating Sounds  . . . . . .22
Consumer Support
Consumer Support  . . . . .Back Cover
Product Registration 
for Canadian Customers  . . . . .29, 30
Product Registration 
for U.S. Customers  . . . . . . . . .27, 28
Warranty for 
Canadian Customers  . . . . . . . . . . .31
Warranty for U.S. Customers . . . . .32
Réfrigérateurs
Congélateur supérieur
Refrigeradores
Congelador superior
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
Find these numbers on the gray label 
on the left side, near the top of the
refrigerator compartment.
Models 18 & 19
Manuel d’utilisation 
et d’installation
Owner’s Manual and
Installation Instructions
Manual del propietario 
e instalación
La section française commence à la page 34
La sección en español empieza en la página 62

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■ This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■ Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■ Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.

■

■ Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

■

■ In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating element

located on the bottom of the icemaker. Do not

place fingers or hands on the automatic

icemaking mechanism while the refrigerator

is plugged in.

■

■ Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small.

Be careful closing doors when children are

in the area.

■

■ Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

■

■ Setting either or both controls to the 0 (off)

position does not remove power to the light

circuit.

■

■ Do not refreeze frozen foods which have

thawed completely.

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

2

3

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

ge.com

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against

the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not

problems of the past. Junked or abandoned

refrigerators are still dangerous…even if they will

sit for “just a few days.” If you are getting rid of

your old refrigerator, please follow the instructions

below to help prevent accidents.

Before You Throw Away Your Old

Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may

not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an

old refrigeration product, check with the company

handling the disposal about what to do.

4

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with

a 3-prong (grounding) plug which mates with a

standard 3-prong (grounding) wall outlet to

minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility and

obligation to have it replaced with a properly

grounded 3-prong wall outlet.

The refrigerator should always be plugged into its

own individual electrical outlet which has a voltage

rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull

straight out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

USE OF ADAPTER PLUGS (Adapter plugs not permitted in Canada)

Because of potential safety hazards under certain conditions, we strongly recommend against

the use of an adapter plug.

However, if you must use an adapter, where local

codes permit, a temporary connection may be made

to a properly grounded 2-prong wall outlet by use

of a UL-listed adapter available at most local

hardware stores.

The larger slot in the adapter must be aligned with

the larger slot in the wall outlet to provide proper

polarity in the connection of the power cord.

When disconnecting the power cord from the

adapter, always hold the adapter in place with one

hand while pulling the power cord plug with the

other hand. If this is not done, the adapter ground

terminal is very likely to break with repeated use.

If the adapter ground terminal breaks, DO NOT USE

the refrigerator until a proper ground has been

established.

Attaching the adapter ground terminal to a wall outlet

cover screw does not ground the appliance unless the

cover screw is metal, not insulated, and the wall outlet is

grounded through the house wiring. You should have the

circuit checked by a qualified electrician to make sure the

outlet is properly grounded.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions

Installation Instructions

About the controls on the refrigerator. ge.com

Control Settings

Initially, set the refrigerator control at 5 and the freezer control at 5, and allow 24 hours

for the temperature to stabilize.

Several adjustments may be required. Adjust the controls one increment at a time and

allow 12 hours after each adjustment for the refrigerator to reach the temperature you

have set.

Setting the refrigerator control to 0 stops cooling in both the freezer and refrigerator

compartments but does not shut off electrical power to the refrigerator. The freezer

control has no effect on electrical power to the refrigerator.

Control settings will vary based on personal preferences, usage and operating conditions,

and may require more than one adjustment. Factors that affect temperature include the

amount of food in the refrigerator or freezer, the frequency of door openings and the

temperature of food when it is placed in the refrigerator.

5

6

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

“Walking” the shelf

In some models, moving the shelf between

the lower and upper position may require

“walking” the shelf as shown. Lift up the left

side of the shelf and slide it left into the

center of the shelf supports. Then swing the

right side upwards and insert it into the

center of the upper shelf supports. Slide the

left side out of the shelf supports, swing it

upwards until level with the right side and

slide it into the shelf supports. Rest each

end of the shelf on the bottom of the shelf

supports.

Rearranging the Shelves

To remove:

Tilt the shelf up at the front.

Lift the shelf up at the back and bring

the shelf out.

To replace:

While tilting the shelf up, insert the top

hook at the back of the shelf in a slot

on the track.

Lower the front of the shelf until the

bottom of the shelf locks into place.

Spillproof Shelves (on some models)

Spillproof shelves have special edges to

help prevent spills from dripping to lower

shelves. To remove or replace the shelves,

see Rearranging the Shelves.

About the shelves and bins.

Not all features are on all models.

Some models have wire shelves that

can be adjusted in the same manner.

To remove:

Lift up the left side of the shelf and

slide it left into the center of the shelf

supports.

Rotate the right side of the shelf up and

out of the shelf supports.

Shelves in the refrigerator and freezer compartments are adjustable.

Refrigerator Compartment

Freezer Compartment

To replace:

Holding the shelf diagonally, insert the

left end of the shelf into the center of

the lower shelf supports on the side

wall.

Insert the right end of the shelf into the

shelf supports at the same level. Rest

each end of the shelf on the bottom of

the shelf supports.

NOTE: For models with an automatic icemaker,

the freezer shelf must be in the lower position for

the ice cube bucket to catch the cubes.

7

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions

Installation Instructions

Non-Adjustable Shelves on the Door

Detachable shelves deepen and enclose

fixed door shelves, providing more storage

room and greater storage flexibility.

To remove: Lift the shelf straight up; then

pull out.

To replace: Engage the shelf extender in

the molded supports on the door and push

down. It will lock in place.

Freezer Tilt-Out Bin (on some models)

Push the button as you tilt out the bin.

To remove: Hold the sides of the bin and

lift it straight up; then pull out.

To replace: Engage the ends of the bin

in the molded supports on the door and

push down. It will lock in place.

NOTE: Do not overload the bin.

Button

ge.com

Adjustable Bins on the Door (on some models)

Adjustable bins can easily be carried from

refrigerator to work area.

To remove: Lift bin straight up; then pull out.

To replace or relocate: Engage the bin in the

molded supports of the door and push

down. Bin will lock in place.

The snugger (on some models) helps prevent

tipping, spilling or sliding of small items

stored on the door shelf. Grip the finger

hold near the rear of the snugger and move

it to fit your needs.

NOTE: Bins for the refrigerator and freezer

doors are different sizes and are not

interchangeable.

Snugger

Finger hold

Slide-Out Spillproof Shelf (on some models)

The slide-out spillproof shelf allows you

to reach items stored behind others. The

special edges are designed to help prevent

spills from dripping to lower shelves.

NOTE: The shelves are shipped with tape on

the back. Remove this tape before attempting

to remove the shelf.

To remove:

Remove all items from shelf.

Slide the shelf out until it stops.

Lift the front edge of the shelf until the

tabs are above the shelf frame.

Continue pulling the shelf forward until

it can be lifted out and removed.

To replace:

Place the rear of the shelf on the shelf

frame just behind the front bar.

Slide the shelf back until the tabs are

above the openings.

Lower the shelf so that the tabs go into

the openings; then slide the shelf all the

way in.

Make sure that the shelf sits flat after reinstallation

and doesn’t move freely from side to side.

Make sure you push the shelves all the way in

before you close the door.

Tab

Opening

Front bar

8

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

About the crispers and pans.

Not all features are on all models.

Adjustable Humidity Crisper (on some models)

Slide the control all the way to the

HIGH setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the LOW

setting to provide lower humidity levels

recommended for most fruits.

Fruit and Vegetable Crispers

Excess water that may accumulate in

the bottom of the drawers or under the

drawers should be wiped dry.

Snack Pan (on some models)

This pan can be moved to the most useful

location for your family’s needs.

To remove, slide the pan out to the stop

position, lift the pan up and past the stop

position, and lift out.

ShelfSaver

™

Rack

This slide-out rack holds twelve cans of

soda or two wine/water bottles (lengthwise).

Can be removed for cleaning.

To remove, slide the rack out to the stop

position, lift the rack up and past the stop,

and lift out.

About crisper removal. ge.com

Not all features are on all models.

Crisper Removal

Unload the bottom shelf before attempting to

remove the storage drawers.

To Remove:

Lift the drawers up slightly while pulling

them past the stop location.

When the door cannot be fully opened:

Pull the drawer farthest from the door

straight out. Slide the other drawer toward

the middle and remove it.

To remove the glass cover:

Remove the glass, then the frame. When

replacing the glass, push the rear edge

firmly into the frame.

Push up the glass cover at the front.

Slide the glass cover forward until the

back edge comes out of the frame.

Rotate the side of the glass cover up.

Remove the glass cover.

To remove the frame:

Lift up the front of the frame using

both hands.

Slide the frame forward.

Rotate the side of the frame up.

Remove the frame.

2

4

3

1

About the additional features.

Not all features are on all models.

Removing the glass cover

2

4

3

1

Removing the frame

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions

Installation Instructions

9

10

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Water Filter Accessory

The water filter is an option at extra cost

and is available from your dealer. Specify

WR97X0214. It has complete installation

instructions and installs on 1/4″ O.D.

copper water line or plastic tubing that is

included in a GE SmartConnect

™

Refrigerator Tubing kit. When using the

plastic tubing, an additional piece of plastic

tubing (WX08X10002) must also be

ordered since the plastic tubing should

not be cut.

NOTE: The only GE approved plastic tubing is that

supplied in GE SmartConnect

™

Refrigerator Tubing

kits. Do not use any other plastic water supply line

because the line is under pressure at all times.

Certain types of plastic will crack or rupture with

age and cause water damage to your home.

Automatic Icemaker (on some models)

The icemaker will produce approximately

3 to 3-1/2 lbs. of ice in a 24-hour period,

depending on the freezer compartment

temperature, room temperature, number

of door openings and other use conditions.

There are two types of icemakers: power

switch models and feeler arm models.

If the refrigerator is operated before the

water connection is made to the icemaker,

set the power switch to O (off) or move the

feeler arm to the STOP (up) position.

When the refrigerator has been connected

to the water supply, set the power switch to

the I (on) position or move the feeler arm to

the ON (down) position. On power switch

models, the green light will come on.

The icemaker will fill with water when it

cools to 15°F. A newly-installed refrigerator

may take 12 to 24 hours to begin making

ice cubes.

Once the icemaker starts to make ice, it

may take up to 48 hours to fill the bin,

depending on the temperature settings

and number of door openings.

Throw away the first few batches of ice to

allow the water line to clear.

Be sure nothing interferes with the sweep

of the feeler arm.

When the bin fills to the level of the feeler

arm, the icemaker will stop producing ice.

It is normal for several cubes to be joined

together.

If ice is not used frequently, old ice cubes

will become cloudy, taste stale, shrink or

fuse together.

On power switch models, the green power

light will blink if ice cubes get stuck in the

icemaker. To correct this, set the power

switch to O (off) and remove the cubes. Set

the power switch to I (on) to restart the

icemaker. After the icemaker has been

turned on again, there will be a delay of

about 45 minutes before the icemaker

resumes operation.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle multiple

times when making one batch of ice.

About the automatic icemaker.

A newly-installed refrigerator may take 12–24 hours to begin making ice.

Icemaker Accessory Kit

If your refrigerator did not already come

equipped with an automatic icemaker,

an icemaker accessory kit is available at

extra cost.

Check the back of the refrigerator

for the specific icemaker kit needed for

your model.

Icemaker

Feeler Arm

Power

Switch

Green

Power Light

Feeler Arm in

the STOP

(up) position

Feeler Arm in

the ON (down)

position

Feeler arm model

Power switch model

There are two types of icemakers:

Be careful when moving the refrigerator

away from the wall. All types of floor

coverings can be damaged, particularly

cushioned coverings and those with

embossed surfaces.

Pull the refrigerator straight out and return

it to position by pushing it straight in.

Moving the refrigerator in a side direction

may result in damage to the floor covering

or refrigerator.

When pushing the refrigerator back, make sure

you don’t roll over the power cord or icemaker

supply line (on some models).

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

11

Cleaning the Outside

The door handles and trim. Clean with

a cloth dampened with soapy water.

Dry with a soft cloth.

Keep the outside clean. Wipe with a clean

cloth lightly dampened with kitchen

appliance wax or mild liquid dish

detergent. Dry and polish with a clean,

soft cloth.

The stainless steel panels and door handles

(on some models) can be cleaned with a

commercially available stainless steel

cleaner. Do not use appliance wax or polish

on the stainless steel.

Do not wipe the refrigerator with a soiled dish

cloth or wet towel. These may leave a residue

that can erode the paint. Do not use scouring

pads, powdered cleaners, bleach or cleaners

containing bleach because these products can

scratch and weaken the paint finish.

Cleaning the Inside

To help prevent odors, leave an open box of

baking soda in the fresh food and freezer

compartments.

Unplug the refrigerator before cleaning. If this

is not practical, wring excess moisture out

of sponge or cloth when cleaning around

switches, lights or controls.

Use warm water and baking soda solution—

about a tablespoon (15 ml) of baking soda

to a quart (1 liter) of water. This both

cleans and neutralizes odors. Thoroughly

rinse and wipe dry.

Avoid cleaning cold glass shelves (on some

models) with hot water because the extreme

temperature difference may cause them to

break. Handle glass shelves carefully. Bumping

tempered glass can cause it to shatter.

Do not wash any plastic refrigerator parts in

the dishwasher.

Do not clean with any products containing

detergent, bleach or ammonia. They may

damage the refrigerator.

Condenser

There is no need for routine condenser

cleanings in normal home operating

environments. However, in environments

that may be particularly dusty or greasy, the

condenser should be cleaned periodically

for efficient refrigerator operation.

Removing the base grille:

First remove the base grille. Grasp the base

grille about 6 inches from each end and

pull its bottom edge toward you.

Cleaning the condenser:

Sweep away or vacuum up dust.

For best results, use a brush specially

designed for this purpose. It is available at

most appliance parts stores.

Replacing the base grille:

Replace the base grille by inserting the

tops of the metal clips into the oval vents,

making sure one of the plastic tabs on the

back of the grille goes into each of the oval

vents. Then push the bottom of the grille

forward until it snaps into place.

Behind the Refrigerator

Care and cleaning of the refrigerator.

ge.com

12

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Replacing the light bulbs.

Setting either or both controls to 0 (off) does not remove power to the light circuit.

Refrigerator Compartment–Upper Light

CAUTION: Light bulbs may be hot.

Unplug the refrigerator.

The bulbs are located at the top of the

compartment near the opening.

Replace with an appliance bulb of

the same or lower wattage.

Plug the refrigerator back in.

Freezer Compartment Dome Light (on some models)

CAUTION: Light bulbs may be hot.

Unplug the refrigerator.

The bulb is located at the top of the

freezer compartment inside the dome

light shield. To remove the shield,

place your fingers in the pockets at

the back of the shield. Pull the shield

forward and down.

After replacing with an appliance bulb

of the same or lower wattage, replace

the shield.

Plug the refrigerator back in.

Some models have only one light.

Care and cleaning of the refrigerator.

Preparing for Vacation

For long vacations or absences, remove

food and unplug the refrigerator. Move

the refrigerator control to the 0 (off)

position and clean the interior with a

baking soda solution of one tablespoon

(15 ml) of baking soda to one quart

(1 liter) of water. Leave the doors open.

Set the icemaker power switch to the O (off)

position or move the feeler arm to the

STOP (up) position (depending on model)

and shut off the water supply to the

refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water

supply system (on some models) to prevent

serious property damage due to flooding.

Preparing to Move

Secure all loose items such as grille,

shelves and drawers by taping them

securely in place to prevent damage.

Be sure the refrigerator stays in an upright

position during moving.

Pockets

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these

instructions for local inspector’s use.

•

IMPORTANT – Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions

for future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time – Refrigerator Installation

15 minutes.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

• Do not install the refrigerator where the temperature

will go below 60°F (16°C) because it will not run often

enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature

will go above 100°F (37°C) because it will not perform

properly.

• Install it on a floor strong enough to support it fully

loaded.

REFRIGERATOR LOCATION

If you have questions, call 1.800.GE.CARES or visit our Website at: ge.com

Installation

Refrigerator

Instructions

Models 18 and 19

Allow the following clearances for ease of installation,

proper air circulation and plumbing and electrical

connections.

• Sides 1/8″ (3 mm)

• Top 1″ (25 mm)

• Back 1″ (25 mm)

If the refrigerator is to be installed next to a wall on the

hinge side, allow 5/16″ (8 mm) door clearance.

CLEARANCES

The leveling legs have 2 purposes:

• Leveling legs adjust so the door closes easily when

opened about 45°.

• Leveling legs adjust so the refrigerator is firmly

positioned on the floor and does not wobble.

• Rollers allow you to move the refrigerator away from the

wall for cleaning.

NOTE: When leveling legs are properly adjusted, the top

of the refrigerator will not be level but will have a slight

backward tilt.

Adjust front leveling legs so

that refrigerator is in solid

contact with floor and door

swings closed when partially

opened.

Check door alignment and

gasket seal after adjusting

leveling legs.

LEVELING LEGS

If the refrigerator has an icemaker, it will have to

be connected to a cold water line. A GE water supply

kit (containing tubing, shutoff valve, fittings and

instructions) is available at extra cost from your

dealer or by visiting our Website at ge.com or

Parts and Accessories, 800.626.2002.

WATER SUPPLY TO THE ICEMAKER

(ON SOME MODELS)

13

Clockwise

to Raise

Refrigerator

14

INSTALLING THE WATER LINE

(ON SOME MODELS)

Recommended copper water supply kits are WX8X2,

WX8X3 or WX8X4, depending on the amount of

tubing you need. Approved plastic water supply lines

are GE SmartConnect

™

Refrigerator Tubing

(WX08X10002, WX08X10006, WX08X10015 and

WX08X10025).

When connecting your refrigerator to a GE Reverse

Osmosis Water System, the only approved installation

is with a GE RVKit. For other reverse osmosis water

systems, follow the manufacturer’s recommendations.

This water line installation is not warranted by the

refrigerator or icemaker manufacturer. Follow these

instructions carefully to minimize the risk of expensive

water damage.

Water hammer (water banging in the pipes) in house

plumbing can cause damage to refrigerator parts and

lead to water leakage or flooding. Call a qualified

plumber to correct water hammer before installing the

water supply line to the refrigerator.

To prevent burns and product damage, do not hook

up the water line to the hot water line.

If you use your refrigerator before connecting the

water line, make sure the icemaker power switch is in

the O (off) position (on power switch models) or the

feeler arm is in the STOP (up) position (on feeler arm

models).

Do not install the icemaker tubing in areas where

temperatures fall below freezing.

When using any electrical device (such as a power

drill) during installation, be sure the device is double

insulated or grounded in a manner to prevent the

hazard of electric shock, or is battery powered.

All installations must be in accordance with local

plumbing code requirements.

BEFORE YOU BEGIN

Installation Instructions

WHAT YOU WILL NEED

• Copper or GE SmartConnect

™

Refrigerator Tubing

kit, 1/4″ outer diameter to connect the refrigerator

to the water supply. If using copper, be sure both ends

of the tubing are cut square.

To determine how much tubing you need: Measure

the distance from the water valve on the back of the

refrigerator to the water supply pipe. Then add 8′

(2.4 m). Be sure there is sufficient extra tubing (about

8′ [2.4 m] coiled into 3 turns of about 10″ [25 cm]

diameter) to allow the refrigerator to move out from

the wall after installation.

GE SmartConnect

™

Refrigerator Tubing Kits are

available in the following lengths:

2′ (.6 m) – WX08X10002

6′ (1.8 m) – WX08X10006

15′ (4.6 m) – WX08X10015

25′ (7.6 m) – WX08X10025

Be sure that the kit you select allows at least 8′ (2.4 m)

as described above.

NOTE: The only GE approved plastic tubing is that

supplied in GE SmartConnect

™

Refrigerator Tubing

kits. Do not use any other plastic water supply line

because the line is under pressure at all times. Certain

types of plastic will crack or rupture with age and cause

water damage to your home.

15

• A GE water supply kit (containing tubing, shutoff

valve and fittings listed below) is available at extra

cost from your dealer or from Parts and Accessories,

800.626.2002.

• A cold water supply. The water pressure must be

between 20 and 120 p.s.i. (1.4–8.1 bar).

• Power drill.

• 1/2″ or adjustable wrench.

• Straight and Phillips blade screwdriver.

• Two 1/4 ″ outer diameter compression nuts and

2 ferrules (sleeves)—to connect the copper tubing to

the shutoff valve and the refrigerator water valve.

OR

• If you are using a GE SmartConnect

™

Refrigerator

Tubing kit, the necessary fittings are preassembled to

the tubing.

• If your existing copper water line has a flared fitting

at the end, you will need an adapter (available at

plumbing supply stores) to connect the water line to

the refrigerator OR you can cut off the flared fitting

with a tube cutter and then use a compression fitting.

Do not cut formed end from GE SmartConnect

™

Refrigerator tubing.

• Shutoff valve to connect to the cold water line.

The shutoff valve should have a water inlet with a

minimum inside diameter of 5/32″ at the point of

connection to the COLD WATER LINE. Saddle-type

shutoff valves are included in many water supply kits.

Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes.

WHAT YOU WILL NEED (CONT.)

Installation Instructions

SHUT OFF THE MAIN WATER

SUPPLY

Turn on the nearest faucet long enough to clear

the line of water.

Install the shutoff valve on the nearest frequently used

drinking water line.

1

Choose a location for the valve that is easily

accessible. It is best to connect into the side of a

vertical water pipe. When it is necessary to connect

into a horizontal water pipe, make the connection

to the top or side, rather than at the bottom, to

avoid drawing off any sediment from the water pipe.

CHOOSE THE VALVE LOCATION

2

Drill a 1/4″ hole in the water pipe (even if using a

self-piercing valve), using a sharp bit. Remove any

burrs resulting from drilling the hole in the pipe.

Take care not to allow water to drain into the drill.

Failure to drill a 1/4″ hole may result in reduced

ice production or smaller cubes.

DRILL THE HOLE FOR THE VALVE

3

16

Place the compression nut and ferrule (sleeve)

for copper tubing onto the end of the tubing and

connect it to the shutoff valve.

Make sure the tubing is fully inserted into the valve.

Tighten the compression nut securely.

For plastic tubing from a GE SmartConnect

™

Refrigerator Tubing kit, insert the molded end

of the tubing into the shutoff valve and tighten

compression nut until it is hand-tight; then tighten

one additional turn with a wrench. Overtightening

may cause leaks.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

CONNECT THE TUBING

TO THE VALVE

7

Turn the main water supply on and flush out the

tubing until the water is clear.

Shut the water off at the water valve after about

one quart (1 liter) of water has been flushed

through the tubing.

FLUSH OUT THE TUBING

8

INSTALLING THE WATER LINE

(CONT.)

Installation Instructions

Saddle-Type

Shutoff Valve

Compression

Nut

SmartConnect

™

Tubing

Packing Nut

Outlet Valve

Ferrule (sleeve)

Fasten the shutoff valve to the cold water pipe with

the pipe clamp.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

FASTEN THE SHUTOFF VALVE

4

Tighten the clamp screws until the sealing washer

begins to swell.

NOTE: Do not overtighten or you may crush the

tubing.

TIGHTEN THE PIPE CLAMP

5

Route the tubing between the cold water line and

the refrigerator.

Route the tubing through a hole drilled in the wall

or floor (behind the refrigerator or adjacent base

cabinet) as close to the wall as possible.

NOTE: Be sure there is sufficient extra tubing

(about 8′ [2.4 m] coiled into 3 turns of about 10″

[25 cm] diameter) to allow the refrigerator to move

out from the wall after installation.

ROUTE THE TUBING

6

Washer

Inlet End

Pipe Clamp

Clamp Screw

Vertical Cold

Water Pipe

Saddle-Type

Shutoff Valve

Pipe Clamp

17

On power switch models, set the icemaker power

switch to the l (on) position. On feeler arm models,

move the feeler arm to the ON (down) position. The

icemaker will not begin to operate until it reaches

its operating temperature of 15°F (–9°C) or below.

It will then begin operation automatically.

NOTE: In lower water pressure conditions, the

water valve may turn on up to 3 times to deliver

enough water to the icemaker.

NOTES:

• Before making the connection to the refrigerator,

be sure the refrigerator power cord is not

plugged into the wall outlet.

• We recommend installing a water filter if your

water supply has sand or particles that could clog

the screen of the refrigerator’s water valve. Install

it in the water line near the refrigerator. If using

GE SmartConnect

™

Refrigerator Tubing kit, you

will need an additional tube (WX08X10002) to

connect the filter. Do not cut plastic tube to

install filter.

Remove the screws holding the right side of the

access cover. Fold back the cover.

Remove the plastic flexible cap

from the water valve

(refrigerator connection).

Place the compression nut and

ferrule (sleeve) onto the end of

the tubing as shown. On GE

SmartConnect

™

Refrigerator

Tubing kit, the nuts are already

assembled to the tubing.

Insert the end of the tubing into the water valve

connection as far as possible. While holding the

tubing, tighten the fitting.

For plastic tubing from a GE SmartConnect

™

Refrigerator Tubing kit, insert the molded end

of the tubing into the water valve connection and

tighten compression nut until it is hand-tight;

then tighten one additional turn with a wrench.

Overtightening may cause leaks.

Fasten the tubing into the clamp provided to hold

it in a vertical position. You may need to pry open

the clamp.

CONNECT THE TUBING TO THE

REFRIGERATOR

9

Installation Instructions

Tighten any connections that leak.

TURN THE WATER ON AT THE

SHUTOFF VALVE

10

Arrange the coil of tubing so that it does not vibrate

against the back of the refrigerator or against the

wall. Push the refrigerator back to the wall.

PLUG IN THE REFRIGERATOR

11

START THE ICEMAKER

Power

switch

Reattach the access cover.

1/4″

Compression

Nut

Tubing

Clamp

1/4″ Tubing

Ferrule

(sleeve)

Refrigerator

Connection

SmartConnect

™

Tubing

Power switch model

Feeler Arm in the

STOP (up) position

Feeler Arm in

the ON (down) position

Feeler arm model

TRANSFER TOP HINGE TO

THE LEFT

Interchange hinge and screws at top right with screws

at the top left of the refrigerator. On some models,

screw caps must be removed with a putty knife or a

thin-blade screwdriver before removing screws. Align

the holes in the top of the refrigerator with three of

the holes in the hinge.

Do not tighten screws on hinge side at this time.

2

REVERSING THE DOOR SWING

When reversing the door swing:

• Read the instructions all the way through before

starting.

• Handle parts carefully to avoid scratching paint.

• Set screws down by their related parts to avoid using

them in the wrong places.

• Provide a non-scratching work surface for

the doors.

IMPORTANT: Once you begin, do not move the

cabinet until door-swing reversal is completed.

These instructions are for changing the hinges from

the right side to the left side—if you ever want to

change the hinges back to the right side, follow these

same instructions and reverse all references to left and

right.

• Once door swing is finalized, ensure the logo badge

is properly aligned and permanently secured to the

door by removing the adhesive cover on the back

side. NOTE: If necessary call Customer Service for

a replacement badge.

Unplug the refrigerator from its electrical outlet.

Empty all door shelves, including the dairy

compartment.

IMPORTANT NOTES

Installation Instructions

REMOVE THE FREEZER DOOR

1

Tape the door shut with masking tape.

Remove the tape and tilt the door away from the

refrigerator. Lift it off the center hinge pin.

Set the door on a non-scratching surface with the

inside up.

Remove the hinge cover on top of the freezer door

(on some models).

Remove the three Phillips screws, then lift the hinge

straight up to free the hinge pin from the socket in

the top of the door. Ensure that the door thimble

remains on the hinge pin or inside door hinge

pin hole located in the top of the door.

18

TOOLS YOU WILL NEED

Putty Knife or

Thin-blade Screwdriver

Masking Tape

Adjustable Wrench

3/8″ and 10 mm Socket

Ratchet/Driver

Phillips Screwdriver

Top Hinge

Door Thimble

A

B

C

D

Screws

Installation Instructions

REMOVE THE REFRIGERATOR DOOR

3

Tape the door shut with masking tape.

Remove the plastic washer, center hinge pin

and door thimble with the 3/8″ (10mm) socket

ratchet/driver.

Remove the tape and tilt the door away from the

refrigerator. Tilt the door and lift to free its bottom

socket from the pin in the bottom hinge bracket.

Ensure that the door thimble remains on the hinge

pin or inside door hinge pin hole located in the

bottom of the doors.

Set the door on a non-scratching surface with the

inside up.

CAUTION: Do not let door drop to the floor.

To do so could damage the door stop.

Plastic Washer

Center Hinge Pin

Center Hinge Bracket

Door Thimble

A

B

C

TRANSFER CENTER HINGE

BRACKET TO THE LEFT

Remove the center hinge bracket with a Phillips

screwdriver.

On some models, you will need to remove the caps

from the screw heads before you can remove the

screws. Use the edge of a thin blade to gently pry the

caps off the screw heads. (A putty knife works well for

this.) Cover the blade with tape to prevent scratching

the paint.

Remove the three Phillip’s screws from the center

left side of the refrigerator. Screw them into the

holes on the right side. Replace the caps by

snapping them over the screws with your finger.

Place the center hinge bracket over the holes at

the center left side of the refrigerator. Insert and

tighten the three screws.

4

A

C

D

19

TRANSFER BOTTOM HINGE

BRACKET TO THE LEFT

Using a Phillips screwdriver, remove the bottom hinge

bracket, plastic washer, and door thimble from the

right side.

NOTE: If the door thimble is not on the hinge

bracket, check to see if it is stuck to the bottom of

the door.

5

Plastic Washer

Bracket with

Hinge Pin

Door Thimble

Screws

A

Remove the hinge pin from the hinge pin bracket by

removing the nut and the metal lock washer.

B

Metal Lock

Washer

Hinge Pin

Nut

Place the bottom hinge pin in the left hole. Reinstall

the metal lock washer and the nut.

On some models, you will need to remove the

caps from the screw heads before you can remove the

screws on the left side. Use the edge of a thin-blade

screwdriver to pry the caps off the screw heads

(a putty knife works well for this.) Cover the

blade with tape to prevent scratching the paint.

Remove the three Phillip’s screws from the bottom left

side of the refrigerator. Screw them into the holes on

the right side. On models with screw caps, insert screw

caps over the screws.

Place the bottom hinge bracket over the holes at the

bottom left side of the refrigerator. Insert and tighten

the three Phillip’s screws. Replace the plastic washer

and door thimble.

C

D

E

F

Plastic Washer

Hinge

Bracket

Door Thimble

Screws

B

Screw Cap

Installation Instructions

REVERSING THE DOOR SWING (CONT.)

REMOVE DOOR STOPS FROM

THE RIGHT

On each door, remove the metal door stop from the

bottom right side of the doors. Place the door stops

and screws aside until the handles are transferred to

the right side of the doors.

6

20

Door Stop

Right Side

TRANSFER REFRIGERATOR

DOOR HANDLE TO THE RIGHT

Remove the two

screws holding the

handle to the top of

the door.

Slide the handle

up on the fastener and

remove the handle.

Remove the handle

fastener with the

Phillip’s screwdriver.

Transfer the

fastener to the right

side and move the

threaded plug button

to the left side of the

refrigerator door. Fastener should be flush with the

door—DO NOT overtighten.

7

After removing the handle: Move the small plug

buttons from the top right side of the door top and

insert them into the holes on the opposite side.

Small Plug

Buttons

Move the large plug button from the left edge of the

door and insert it into the hole on the opposite side.

Repeat this step on the bottom of the door.

Plug Button

1

2

3

4

Fastener

Threaded

Plug

Button

TRANSFER REFRIGERATOR DOOR

HANDLE TO THE RIGHT

(CONT.)

7

Reinstalling the handle: Attach the handle to the

right side of the door.

Attach the handle

to the fastener and

slide it down into

position. Line up

the handle with the

screw holes in the top

of the door and

tighten the screws.

1

2

TRANSFER FREEZER DOOR

HANDLE TO THE RIGHT

Remove the two

screws holding the

handle to the bottom

of the door. Slide

the handle down on

the fastener and

remove the handle.

Remove the handle

fastener with a Phillip’s

screwdriver. Transfer

the fastener to the right side and move the GE badge

to the left side of the freezer door. Fastener should be

flush with the door—DO NOT overtighten.

1

2

3

4

Fastener

8

Move the large plug

button from the left edge

of the door and insert it

into the hole on the

opposite side. Repeat this

step on the bottom of the

door.

Plug Button

Attach the handle

to the fastener and slide

it up into position.

Line up the handle

with the screw holes in

the bottom of the door

and tighten the screws.

2

Reinstalling the handle: Attach the handle to the

right side of the door.

1

La page charge ...

GE GTS18TCSCC Le manuel du propriétaire

GE GTS18TCSCC Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents