JVC Cassette Player KS-FX210 Manuel utilisateur
- Catégorie
- Récepteurs multimédia de voiture
- Taper
- Manuel utilisateur
Ce manuel convient également à
KS-FX210 [EN] GET0052-001A [J]
INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MANUEL D’INSTRUCTIONS
For customer Use:
Enter below the Model No. and
Serial No. which are located on
the top or bottom of the cabinet.
Retain this information for future
reference.
Model No.
Serial No.
GET0052-001A
[J]
For installation and connections, refer to the separate manual.
Para la instalación y las conexiones, refiérase al manual separado.
Pour l’installation et les raccordements, se référer au manuel séparé.
ENGLISH
ESPAÑOL
FRANÇAIS
KS-FX210
KS-FX210
KS-FX210
CASSETTE RECEIVER
RECEPTOR-REPRODUCTOR DE CASSETTE
RADIOCASSETTE
EN00COVER.KS-FX210[J]f 10/8/01, 10:13 AM3
2
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
How to reset your unit
Press and hold both the SEL (Select) and (Standby/On/Attenuator) buttons at the same
time for several seconds.
This will reset the built-in microcomputer.
Note:
• Your preset adjustments — such as preset channels or sound adjustments — will also be erased.
SEL (Select)
(Standby/On/Attenuator)
EN02-03-KS-FX210[J]f 10/8/01, 10:13 AM2
3
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
Thank you for purchasing a JVC product. Please read all instructions carefully before operation,
to ensure your complete understanding and to obtain the best possible performance from the unit.
CONTENTS
How to reset your unit .............................. 2
LOCATION OF THE BUTTONS ........... 4
Control panel............................................ 4
BASIC OPERATIONS ...................... 5
Turning on the power ............................... 5
RADIO BASIC OPERATIONS ............. 6
Listening to the radio................................ 6
Storing stations in memory ...................... 7
Tuning into a preset station...................... 8
Other convenient tuner functions ............. 9
TAPE OPERATIONS ....................... 10
Listening to a cassette ............................. 10
SOUND ADJUSTMENTS.................. 11
Turning on/off the loudness function ........ 11
Selecting preset sound modes................. 11
Adjusting the sound ................................. 11
Storing your own sound adjustments....... 12
BEFORE USE
*
For safety....
• Do not raise the volume level too much, as this
will block outside sounds, making driving
dangerous.
• Stop the car before performing any complicated
operations.
*
Temperature inside the car....
If you have parked the car for a long time in hot
or cold weather, wait until the temperature in the
car becomes normal before operating the unit.
OTHER MAIN FUNCTIONS ............... 13
Setting the clock....................................... 13
Detaching the control panel ..................... 14
CD CHANGER OPERATIONS ............. 15
Playing CDs ............................................. 15
Selecting CD playback modes ................. 16
MAINTENANCE ............................ 17
TROUBLESHOOTING ..................... 18
SPECIFICATIONS.......................... 19
EN02-03-KS-FX210[J]f 10/8/01, 10:13 AM3
ENGLISH
4
KS-FX210 [EN] GET0052-001A [J]
2
7
8
t
3
5
6
y
u
r
e
w
q
p
1
KS-FX210
KS-FX210
9
4
RND
RPT
CD-CH
MOST
TP
PTY
TP
BEAT POP SOFT
LOUD
i
;
a
gd
A
2
3
o
s
f
LOCATION OF THE BUTTONS
Control panel
1 (Standby/On/Attenuator) button
2 LOUD (Loudness) button
3 0 (Eject) button
4 Cassette compartment
5 1 / ¡ (PROG program) buttons
6 CD-
CH button
7 AM button
8 FM button
9 +/– button
p SEL (Select) button
q 4
/ ¢ buttons
• Also functions as SSM buttons when
pressed together.
w MO (Monaural) button
RND (Random) button
e Number buttons
r DISP (Display) button
t RPT/SCAN (Repeat/Scan) button
y SOUND button
u
(Control panel release) button
Display window
Display window
i RND (Random) indicator
o RPT (Repeat) indicator
; Band indicators
FM1, FM2, FM3,
AM
a CD-CH (CD Changer) indicator
s MO(Monaural) indicator, ST(Stereo) indicator
d Main display
f Sound mode indicators
BEAT, POP, SOFT
g LOUD indicator
EN04-KS-FX210[J]f 10/8/01, 10:14 AM4
5
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
F M
CD-
CH
A M
BASIC OPERATIONS
4
Adjust the sound as you want
(see pages 11 – 12).
To drop the volume in a moment
Press briefly while listening to any
source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.
To turn off the power
Press and hold for more than 1 second.
Note:
When you use this unit for the first time, set the built-in
clock correctly, see page 13.
To increase the volume.
To decrease the volume.
Turning on the power
1
Turn on the power.
Note on One-Touch Operation:
• When you select a source in step 2 below, the
power automatically comes on. You do not
have to press this button to turn on the power.
• If the cassette is already in the cassette
compartment, tape play starts automatically.
However, it is not recommended to leave the
cassette in the compartment when turning off
the power or ignition key. It may damage the
tape head and the cassette.
2
Select the source.
To operate the tuner (FM or AM),
see pages 6 – 9.
To operate the tape,
see page 10.
To operate the CD changer,
see pages 15 – 16.
3
Adjust the volume.
Volume level appears
2
3
1
TP
PTY
TP
EN05-KS-FX210[J]f 10/8/01, 10:14 AM5
6
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
RADIO BASIC OPERATIONS
To stop searching before a station is received,
press the same button you have pressed for
searching.
Searching a station manually:
Manual search
1
Select the band (FM1 – 3, AM).
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to an
FM broadcast.
2
Press and hold ¢ or 4 until
“M” (manual) starts flashing on the
display.
Listening to the radio
You can use either automatic searching or manual
searching to tune into a particular station.
Note:
When a cassette is in the cassette compartment, you
cannot select the tuner. Be sure to eject the cassette from
the cassette compartment to listen to the radio.
Searching a station automatically:
Auto search
1
Select the band (FM1 – 3, AM).
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to an
FM broadcast.
2
Start searching a station.
When a station is received, searching stops.
To search stations of
higher frequencies.
To search stations of
lower frequencies.
Selected band appears
Selected band appears
FM1 FM2
FM3
A M
F M
AM
FM1 FM2
FM3
A M
F M
AM
BEAT POP SOFT
LOUD
BEAT POP SOFT
LOUD
EN06-08-KS-FX210[J]f 10/8/01, 10:14 AM6
7
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
Storing stations in memory
You can use one of the following two methods to
store broadcasting stations in memory.
• Automatic preset of FM stations: SSM (Strong-
station Sequential Memory)
• Manual preset of both FM and AM stations
FM station automatic preset: SSM
You can preset 6 local FM stations in each FM band
(FM1, FM2 and FM3).
1
Select the FM band (FM1 – 3) you
want to store FM stations into.
Each time you press the
button, the FM band changes
as follows:
2
Press and hold both buttons for
more than 2 seconds.
Local FM stations with the strongest signals
are searched and stored automatically in the
band number you have selected (FM1, FM2 or
FM3). These stations are preset in the number
buttons — No.1 (lowest frequency) to No.6 (highest
frequency).
When automatic preset is over, the station stored
in button number 1 will be automatically tuned into.
3
Tune into a station you want while
“M” is flashing.
• If you release your finger from the button,
the manual mode will automatically turn off
after 5 seconds.
• If you hold down the button, the frequency
keeps changing until you release the
button.
When an FM stereo broadcast is hard
to receive:
Press MO/RND (Monaural/Random) while listening
to an FM stereo broadcast.
• Each time you press the button, the MO indicator
lights up and goes off alternately.
When the MO indicator is lit on the display,
the sound you hear becomes monaural but
the reception will be improved (the ST indicator
goes off).
To restore the stereo effect, press the same
button again.
To tune into stations
of higher frequencies.
To tune into stations
of lower frequencies.
“SSM” appears, then disappears when automatic
preset is over.
MO/RND
Lights up when receiving an
FM broadcast in stereo.
FM1 FM2 FM3
F M
ST
BEAT POP SOFT
LOUD
BEAT POP SOFT
LOUD
MO
BEAT POP SOFT
LOUD
EN06-08-KS-FX210[J]f 10/8/01, 10:14 AM7
8
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
Manual preset
You can preset up to 6 stations in each band (FM1,
FM2, FM3 and AM) manually.
Ex: Storing an FM station of 88.3 MHz into the
preset number 1 of the FM1 band
1
Select the band (FM1 – 3, AM) you
want to store stations into (in this
example, FM1).
Each time you press the button, the FM
band changes as follows:
2
Tune into a station of 88.3 MHz.
3
Press and hold the number button
(in this example, 1) for more than
2 seconds.
Preset number “P1” flashes for a while
4
Repeat the above procedure to store
other stations into other preset
numbers.
Notes:
• A previously preset station is erased when a new station
is stored in the same preset number.
• Preset stations are erased when the power supply to
the memory circuit is interrupted (for example, during
battery replacement). If this occurs, preset the stations
again.
Tuning into a preset station
You can easily tune into a preset station.
Remember that you must store stations first. If you
have not stored them yet, see “Storing stations in
memory” on page 7.
1
Select the band (FM1 – 3, AM).
2
Select the number (1 – 6) for the
preset station you want.
To tune into stations
of higher frequencies.
To tune into stations
of lower frequencies.
FM1 FM2
FM3
A M
F M
AM
ST
BEAT POP SOFT
LOUD
FM1 FM2 FM3
F M
ST
BEAT POP SOFT
LOUD
EN06-08-KS-FX210[J]f 10/8/01, 10:14 AM8
9
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
Other convenient tuner
functions
Scanning broadcast stations
When you press RPT/SCAN while
listening to the radio, station
scanning starts. Each time a
broadcast is tuned in, scanning
stops for about 5 seconds (tuned
frequency number flashes on
the display), and you can check
what program is now being
broadcast.
If you want to listen to that
program, press the same button
again to stop scanning.
Changing the AM/FM channel intervals
When using this unit in an area other than North
or South America:
When this unit is shipped from the factory, the
channel intervals are set to 10 kHz for AM and 200
kHz for FM. You can change the channel intervals
by following the procedure below.
1 Press SEL (Select) for more than 2 seconds.
“CLOCK H”, “CLOCK M” or “AREA” appears on
the display.
2 If “AREA” does not appear, press 4
or
¢ until it appears.
3 Press +.
“AREA EU” appears and the channel intervals
are set to 9 kHz for AM and 50 kHz (for manual
tuning) / 100 kHz (for searching) for FM.
To reset to the factory setting, follow the above
step 1 and 2, then press – in step 3 (“AREA US”
appears on the display.)
AREA EU : Select this when used in an area
other than North and South America.
AREA US: Select this when used in North or
South America.
RPT
SCAN
EN09-KS-FX210[J]f 10/8/01, 10:14 AM9
10
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
TAPE OPERATIONS
Listening to a cassette
You can playback type 1 (normal) tapes.
1
Turn on the power.
Note on One-Touch Operation:
If a cassette is already in the cassette compartment,
tape play starts automatically. However, it is not
recommended to leave the cassette in the compartment
when turning off the power or ignition key. It may
damage the tape head and the cassette.
2
Insert a cassette into the cassette
compartment.
When one side of the
tape reaches its end
during play, the other
side of the tape
automatically starts
playing. (Auto Reverse)
3
Select the tape direction.
Press both buttons at
the same time.
Each time you press both
buttons, the tape direction
changes alternately –
forward (
) and
reverse (
).
To stop play and eject the cassette.
Press 0.
Tape play stops and the cassette automatically
ejects from the cassette compartment. The source
changes to the previously selected one.
• You cannot change the source if the cassette is
still in the cassette compartment.
To change source, you must eject the cassette
first.
• You can also eject the cassette by pressing 0
while the unit is turned off.
To fast-wind a tape.
Press in ¡ or 1.
The tape will be wound in the direction of the
arrows (¡ or 1).
Tape direction
To restart playback, lightly press the other
button which is not pressed in (1 or ¡).
/I/ATT
PROG
PROG
EN10-KS-FX210[J]f-1 10/8/01, 10:15 AM10
11
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
Turning on/off the loudness
function
The human ear is less sensitive to low and high
frequencies at low volumes.
The loudness function can boost these frequencies to
produce a well-balanced sound at low volume levels.
Each time you press LOUD, the loudness function
turns on and off alternately.
LOUD
Selecting preset sound modes
You can select a preset sound adjustment suitable
to the music genre.
Each time you press SOUND, the sound mode
changes as follows:
SOUND
Indication For
Preset values
BAS TRE LOUD
SCM OFF (Flat sound) 00 00 On
BEAT Rock or disco music +2 00 On
POP Light music +4 +1 Off
SOFT Quiet background music +1 –3 Off
Notes:
• You can adjust the preset sound mode to your
preference, and store it in memory.
If you want to adjust and store your original sound
mode, see “Storing your own sound adjustments” on
page 12.
• To adjust only the bass and treble reinforcement
levels to your preference, see “Adjusting the sound”
on page 11.
• When one of the sound modes is selected, it is shown
on the display as follows:
For example, when “POP” is selected.
|\
Adjusting the sound
You can adjust the sound characteristics to
your preference.
1
Select the item you want to adjust.
Each time you press the button,
the adjustable items change as
follows:
Indication To do Range
BAS Adjust the bass –6 (min.)
(Bass) |
+6 (max.)
TRE Adjust the treble –6 (min.)
(Treble) |
+6 (max.)
FAD* Adjust the front R6 (Rear only)
(Fader)* and rear speaker |
balance F6 (Front only)
BAL Adjust the left L6 (Left only)
(Balance) and right speaker |
balance R6 (Right only)
VOL Adjust the volume 00 (min.)
(Volume) |
50 (max.)
Note:
* If you are using a two-speaker system, set the fader
level to “00”.
2
Adjust the level.
Note:
Normally the + and – buttons work as the volume
control buttons. So you do not have to select
“VOL” to adjust the volume level.
SOUND ADJUSTMENTS
LOUD
To increase the level.
To decrease the level.
(Bass)
(Treble)
(Fader)
(Balance)
(Volume)
LOUD
(BEAT)
(POP)
(SOFT)
EN11-12-KS-FX210[J]f 10/8/01, 10:15 AM11
12
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
Storing your own sound
adjustments
You can adjust the sound modes (BEAT, POP,
SOFT) to your preference and store your own
adjustments in memory.
• There is a time limit in doing the following
procedure. If the setting is canceled before you
finish, start from step 1 again.
1
Call up the sound mode you want
to adjust.
• See page 11 for details.
2
Select “BAS” (Bass) or
“TRE” (Treble).
3
Adjust the bass or treble level.
• See page 11 for details.
4
To turn on or off the loudness
function.
Each time you press LOUD, the loudness
function turns on and off alternately. See page
11 for details.
5
Repeat steps 2 and 3 to adjust the
other items.
6
Press and hold SOUND until the
sound mode you have selected in
step
1
flashes on the display.
Your setting is stored in memory.
7
Repeat the same procedure to store
other settings.
To reset to the factory settings
Repeat the same procedure and reassign the
preset values listed in the table on page 11.
SOUND
LOUD
SOUND
BEAT POP SOFT
LOUD
BEAT POP SOFT
LOUD
EN11-12-KS-FX210[J]f 10/8/01, 10:15 AM12
13
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
OTHER MAIN FUNCTIONS
Setting the clock
1
Press and hold the button for more
than 2 seconds.
“CLOCK H”, “CLOCK M”
or “AREA” appears on the
display.
2
Set the hour.
1 Select “CLOCK H” if not shown on
the display.
2 Adjust the hour.
12
3
Set the minute.
1 Select “CLOCK M”.
2 Adjust the minute.
12
4
Press SEL (Select) to finish
the setting.
To check the current clock time or change
the display mode.
Press DISP (display) repeatedly.
Each time you press the button,
the display mode changes as
follows:
• During tuner operation:
Clock
Frequency
• During tape operation:
Clock
Play mode (tape direction)
• During CD changer operation:
Disc number
Elapsed playing time
Clock
DISP
EN13-14-KS-FX210[J]f-1 10/8/01, 10:15 AM13
14
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
Detaching the control panel
You can detach the control panel when leaving
the car.
When detaching or attaching the control panel, be
careful not to damage the connectors on the back
of the control panel and on the panel holder.
Detaching the control panel
Before detaching the control panel, be sure to
turn off the power.
1
Unlock the control panel.
2
Lift and pull the control panel out of
the unit.
3
Put the detached control panel into
the provided case.
Attaching the control panel
1
Insert the left side of the control
panel into the groove on the
panel holder.
2
Press the right side of the control
panel to fix it to the panel holder.
Note on cleaning the connectors:
If you frequently detach the control panel, the
connectors will deteriorate.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened with
alcohol, being careful not to damage the connectors.
Connectors
EN13-14-KS-FX210[J]f-1 10/8/01, 10:15 AM14
15
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
CD CHANGER OPERATIONS
To check the elapsed playing time.
Press DISP (display)
repeatedly.
Each time you press the
button, the display mode
changes as follows.
To fast forward or reverse the track
To go to the next track or the previous track
Press ¢ briefly, while
playing a CD, to go ahead to
the beginning of the next
track. Each time you press
the button consecutively, the
beginning of the next track is
located and played back.
Press 4
briefly, while
playing a CD, to go back
to the beginning of the
current track. Each time you
press the button
consecutively, the beginning
of the previous track is
located and played back.
We recommend that you use one of the CH-X
series with your unit.
If you have another CD automatic changer, consult
your JVC car audio dealer for connections.
• For example, if your CD automatic changer is one
of the KD-MK series, you need a cord (KS-U15K)
for connecting it to this unit.
Before operating your CD automatic changer:
• Refer also to the Instructions supplied with
your CD changer.
• If no discs are in the magazine of the CD
changer or the discs are inserted upside
down, “NO CD” or “NO DISC” will appear on
the display. If this happens, remove the
magazine and set the discs correctly.
• If “RESET 1 - RESET 8” appears on the
display, something is wrong with the
connection between this unit and the CD
changer. If this happens, check the
connection, connect the connecting cord(s)
firmly if necessary, then press the reset
button of the CD changer.
Playing CDs
1
Select the CD automatic changer.
Playback starts from the first
track of the first disc.
All tracks of all discs are
played back.
Note on One-Touch Operation:
When you press CD-CH, the power automatically
comes on. You do not have to press
to
turn on the power.
CD-CH
Press and hold ¢,
while playing a CD, to fast
forward the track.
Press and hold 4
, while
playing a CD, to reverse the track.
Disc number
Track number
DISP
Elapsed playing time
Disc number Clock
EN15-16-KS-FX210[J]f 10/8/01, 10:16 AM15
16
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
To go to a particular disc directly
Press the number button corresponding to the
disc number to start its playback.
• To select a disc number from 1 – 6:
Press 1 (7) – 6 (12) briefly.
• To select a disc number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than
1 second.
Disc number
Track number
Ex. When disc number 3 is selected
Selecting CD playback modes
To playback tracks at random (Random Play)
Each time you press MO/RND (Mono/Random)
while playing a CD, CD random play mode
changes as follows:
MO/RND
RND1 RND2 Canceled
Mode RND Plays at random
Indicator
RND1 Lights All tracks of the current disc,
(random1)
then the tracks of the next
disc, and so on.
RND2 Flashes All tracks of all discs
(random2)
inserted in the magazine.
To playback tracks repeatedly (Repeat Play)
Each time you press RPT/SCAN (Repeat/Scan)
while playing a CD, CD repeat play mode
changes as follows:
RPT
SCAN
Mode RPT Plays repeatedly
Indicator
RPT1 Lights The current track (or
(repeat1)
specified track).
RPT2 Flashes All tracks of the current disc
(repeat2)
(or specified disc).
RPT1 RPT2 Canceled
7 8 9 10 11 12
EN15-16-KS-FX210[J]f 10/8/01, 10:16 AM16
17
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
MAINTENANCE
This unit requires very little attention, but you will
be able to extend the life of the unit if you follow
the instructions below.
To clean the heads
• Clean the heads after every 10 hours of use
using a wet-type head cleaning tape (available
at an audio store).
When the head becomes dirty, you may realize
the following symptoms:
– Sound quality is reduced.
– Sound level decreases.
– Sound drops out.
• Do not play dirty or dusty tapes.
• Do not touch the highly-polished head with any
metallic or magnetic tools.
To keep the tape clean
• Always store the tapes to their storage cases
after use.
• Do not store tapes in the following places:
– Subject to direct sunlight
– With high humidity
– At extremely hot temperatures
CAUTIONS:
• Do not play the tapes with peeling labels;
otherwise, they can damage the unit.
• Tighten tapes to remove slack since loose tape
may become entangled with the mechanism.
• Do not leave a cassette in the cassette
compartment after use, as the tape may
become slack.
EN17-19-KS-FX210[J]f 10/8/01, 10:16 AM17
18
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
TROUBLESHOOTING
What appears to be trouble is not always serious. Check the following points before calling a
service center.
Symptoms
• A cassette tape cannot be
inserted.
• Cassette tapes become hot.
• Tape sound is at very low
level and sound quality is
degraded.
• Sound is sometimes
interrupted.
• Sound cannot be heard
from the speakers.
• Static noise while listening
to the radio.
• “NO CD” or “NO DISC”
appears on the display.
• “RESET 8” appears on the
display.
• “RESET 1-RESET 7”
appears on the display.
• The unit does not work at
all.
• The CD changer does not
work at all.
Causes
You have tried to insert a
cassette in the wrong way.
This is not a malfunction.
The tape head is dirty.
Connections are not good.
The volume control is turned
to the minimum level.
Connections are incorrect.
The antenna is not connected
firmly.
No CD is in the magazine.
CDs are inserted incorrectly.
This unit is not connected to a
CD changer correctly.
The built-in microcomputer
may function incorrectly due
to noise, etc.
Remedies
I
nsert the cassette with the
exposed tape facing right.
Clean it with a head cleaning
tape.
Check the cords and
connections.
Adjust it to the optimum level.
Check the cords and
connections.
Connect the antenna firmly.
Insert CDs into the magazine.
Insert them correctly.
Connect this unit and the CD
changer correctly and press
the reset button of the CD
changer.
Press the reset button of the
CD changer.
While holding SEL, press
for more than 2
seconds to reset the unit.
(The clock setting and
preset stations stored in
memory are erased.) (See
page 2).
EN17-19-KS-FX210[J]f 10/8/01, 10:16 AM18
19
ENGLISH
KS-FX210 [EN] GET0052-001A [J]
AUDIO AMPLIFIER SECTION
Maximum Power Output:
Front : 40 W per channel
Rear : 40 W per channel
Continuous Power Output (RMS):
Front : 16 W per channel into 4 Ω, 40 Hz
to 20 000 Hz at no more than
0.8% total harmonic distortion.
Rear : 16 W per channel into 4 Ω, 40 Hz
to 20 000 Hz at no more than
0.8% total harmonic distortion.
Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:
Bass : ±10 dB at 100 Hz
Treble: ±10 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance:
2.0 V/20 kΩ load (250 nWb/m)
TUNER SECTION
Frequency Range:
FM : 87.5 MHz to 107.9 MHz
(with channel interval set to 200 kHz)
87.5 MHz to 108.0 MHz
(with channel interval set to 50 kHz)
AM : 530 kHz to 1 710 kHz
(with channel interval set to 10 kHz)
531 kHz to 1 602 kHz
(with channel interval set to 9 kHz)
[FM Tuner]
Usable Sensitivity: 11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity:
16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz):
65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 35 dB
Capture Ratio: 2.0 dB
[AM Tuner]
Sensitivity : 20 µV
Selectivity : 35 dB
CASSETTE DECK SECTION
Wow & Flutter : 0.15% (WRMS)
Fast-Wind Time : 190 sec. (C-60)
Frequency Response : 50 to 14 000 Hz
(normal tape)
Signal-to-Noise Ratio : 52 dB
Stereo Separation : 40 dB
GENERAL
Power Requirement:
Operating Voltage : DC 14.4 V
(11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature:
0°C to +40°C (32°F to 104°F)
Dimensions (W × H × D):
Installation Size : 182 mm × 52 mm × 150 mm
(7-3/16" x 2-1/16 "x 5-15/16")
Panel Size : 188 mm × 58 mm × 14 mm
(7-7/16" x 2-5/16" x 5/8")
Mass: 1.3 kg (2.9 Ibs) (excluding accessories)
Design and specifications subject to change
without notice.
If a kit is necessary for your car, consult your
telephone directory for the nearest car audio
speciality shop.
SPECIFICATIONS
EN17-19-KS-FX210[J]f 10/8/01, 10:16 AM19
KS-FX210 [EN] GET0052-001A [J]
0901KKSFLEJEIN
J
V
C
EN, SP, FR
VICTOR COMPANY OF JAPAN, LIMITED
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to Reset
Still having trouble??
USA ONLY
Call 1-800-252-5722
http://www.jvcservice.com
We can help you!
http://www
.
j
v
cmobile.c
om
Visit us on-line for
Technical Support & Customer Satisfaction Survey.
US RESIDENTS ONLY
EN00COVER.KS-FX210[J]f 10/8/01, 10:13 AM2
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
JVC Cassette Player KS-FX210 Manuel utilisateur
- Catégorie
- Récepteurs multimédia de voiture
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
JVC KS-FX11 Manuel utilisateur
-
-
-
-
-
-
JVC KS-FX12 Manuel utilisateur
-
-
-