EarthWise TC70010 Le manuel du propriétaire

Model TC70010

OWNER’S MANUAL

Tiller/Cultivator

SAVE THIS MANUAL FOR FUTURE REFERENCE

This product has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the owner‘s manual before

using this product.

Thank you for your purchase.

DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING, ASSEMBLY, PART,

SERVICE QUESTIONS? GO TO AMERICANLAWNMOWER.COM OR CALL 1-800-633-1501.

BETWEEN 8 AM – 5 PM EST, MONDAY-FRIDAY FOR ASSISTANCE.

PRODUCT SPECIFICATIONS

Model: TC70010

Power supply voltage: 120V-60HZ Working width: 7-IN or 11-IN

Tine Speed: 350 RPM Working depth max: 8-IN

Power Consumption: 10 Amp

No. Description (P/N) No. Description (P/N)

1 Upper handle section (RTC70010-01) 11 Wheel hub cap (RTC70010-60)

2 Bail wire (RTC70010-17) 12

Wheel frame lock pin (RTC70010-10)

3 Switch box and power cable assembly (RTC70010-02) 13 Motor housing (RTC70010-22)

4 Cable clip (RTC70010-03) 14 Protective shield (RTC70010-33)

5 Cord retainer (RTC70010-04) 15 Tine assembly, D (RTC70010-42)

6 Wing nut (RTC70010-05) 16 Tine assembly, C (RTC70010-43)

7 J-bolt M6 (RTC70010-06) 17 Tine assembly, B (RTC70010-55)

8 Center handle section (RTC70010-07) 18 Tine assembly, A (RTC70010-56)

9 Lower handle section - II (RTC70010-16) 19 Tine lock pin (RTC70010-50)

10 Lower handle section - I (RTC70010-09) 20 Wheel (RTC70010-62)

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 - 5

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 7

Operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 - 9

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Storage . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

TABLE OF CONTENTS

1

2

Model TC70010

Precautions that involve your safety.

Read the instruction manual and follow the warning and safety instructions!

SWITCH OFF! Remove plug from outlet immediately if the cable is damaged or

cut.

SWITCH OFF! Remove plug from outlet before cleaning or maintenance.

Do not use in wet weather conditions.

Wear eye and ear protection.

Keep bystanders at a safe distance.

DANGER! Rotating blades. Keep hands and feet at a safe distance.

DANGER! Of being hit by thrown objects.

Waste electrical products should not be disposed of with household waste. Please recycle

where facilities exist. Check with your Local Authority or retailer for recycling advice.

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

3

Model TC70010

TO REDUCE RISK OF INJURY: Before any use

be sure everyone using this product reads and

understands all safety instructions and other

information contained in this manual.

CAUTION: Wear appropriate personal hearing

protection during use. Under some conditions

and duration of use, noise from this product may

contribute to hearing loss.

Save these instructions and review frequently prior

to use and in instructing others.

WARNING: When using electric gardening

appliances, basic safety precautions should

always be followed to reduce risk of fire, electric

shock, and personal injury, including the following:

READ ALL INSTRUCTIONS

CHECK FOR DAMAGED PARTS - Before further

use of the product, any part that is damaged should

be carefully checked to determine that it will operate

properly and perform its intended function. Check

for alignment of moving parts, binding of moving

parts, breakage of parts, mounting and any other

condition that may affect its operation. Any part that

is damaged should be properly repaired or replaced.

For assistance call our customer service help line at

1-800-633-1501.

AVOID DANGEROUS ENVIRONMENTS - Don’t

use this product in rainy, stormy, damp or wet

locations. Do not operate in gaseous or explosive

atmospheres. Motors in these products normally

spark, and the sparks might Ignite fumes.

KEEP CHILDREN AWAY - All visitors, children and

pets should stay at a safe distance from the work

area.

DRESS PROPERLY- Don’t wear loose clothing or

jewelry and wear protective hair covering to contain

long hair. They can be caught in moving parts.

Use of rubber gloves and substantial footwear is

recommended when working outdoors.

USE SAFETY GLASSES - Wear safety glasses

with side shields or goggles that are marked to

comply with ANSI Z87.1 standard when operating

this product. Use face or dust mask if environment

is dusty.

DOUBLE INSULATION – The tiller/cultivator has

double insulation. This means that all external met-

al parts are insulated from the electrical supply.

This is achieved by introducing an insulation layer

between electrical and mechanical parts. The

double insulation guarantees you the greatest

possible safety.

EXTENSION CORD. Make sure your extension

cord is in good condition. When using an

extension cord be sure it is heavy enough to carry

the current your product will draw. An undersized

extension cord will cause a drop in line voltage

resulting in loss of power and overheating. The

following table shows the correct size to use

depending on cord length and nameplate ampere

rating. If in doubt, use the next heavier gage. The

smaller the gage number, the heavier the cord.

WARNING: Use outdoor extension cords marked

SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJTW-

A, or SJTOWA. These cords are rated for outdoor

use and reduce the risk of electric shock.

It is possible to tie the extension cord and power

cord in a knot to prevent them

from becoming disconnected

during use. Make the knot as

shown, then connect the plug

end of the power cord into the

receptacle end of the extension

cord. This method can also be

used to tie two extension cords

together.

Be aware of the extension cord while operating the

tiller/cultivator. Be careful not to trip on the cord.

Always guide the cord away from the tines.

OVERHEAT PROTECTION - If the tiller/cultivator

is blocked by a foreign object or if the motor is

overloaded, the motor will switch off automatically

by the protection device. Release the trigger lever

and wait for the motor to cool down (approx. 15

minutes) before starting the tiller again.

IMPORTANT SAFETY WARNINGS

GENERAL SAFETY

Minimum Gage for Cord Sets

Volts Total Length of cord in Feet

120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not More American wire Gage

Than Than

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

4

Model TC70010

STAY ALERT - Watch what you are doing. Use

common sense. Do not operate the tiller/cultivator

when you are tired or under the influence of drugs

or medication.

WARNING: Do not operate the tiller/cultivator near

underground electrical cables, telephone lines,

pipes or hoses.

If the tiller/cultivator strikes a foreign body, turn it off

immediately, wait for the tines to stop and check for

damage. If necessary, repair before restarting.

If the tiller/cultivator starts to vibrate abnormally,

turn it off immediately and check for the cause.

Vibration is generally a warning of trouble.

DANGER: RISK OF CUT - Wear gloves and use

caution when cleaning or performing maintenance

on the tiller/cultivator.

Always turn off the tiller/cultivator, disconnect from

the power supply and wait until the tines come to a

complete stop before carrying out any maintenance

or repairs.

CAUTION: Tines do not stop immediately after the

tiller/cultivator is turned off.

CAUTION: Risk of injury. Do not put hands, feet or

any body part or clothing near the rotating tines.

WARNING: California Proposition 65:

This product contains chemicals known to the State

of California to cause cancer, birth defects or other

reproductive harm.

WARNING: Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

WARNING: Some dust and debris created by the

use of this tool could contain chemicals known to

the State of California to cause cancer and birth

defects or other reproductive harm.

Some examples of these chemicals are:

- chemicals in fertilizers

- compounds in insecticides, herbicides, and

pesticides

- arsenic and chromium from chemically treated

lumber

Your risk from exposure to these chemicals varies,

depending on how often you do this type of work.

To reduce your exposure, work in a well-ventilated

area and with approved safety equipment such as

dust masks that are specially designed to filter out

microscopic particles.

GROUND FAULT CIRCUIT INTERRUPTER (GFCI)

protection should be provided on the circuit or outlet

to be used for the tiller/cultivator. Receptacles are

available having built-in GFCI protection and may

be used.

DISCONNECT UNIT from the power supply when

not in use or when servicing or cleaning. Do not

leave unattended.

DON’T ABUSE CORD - Never carry this product

by the cord or yank the cord to disconnect from the

receptacle. Keep cord from heat, oil, and sharp

edges.

USE RIGHT APPLIANCE - Do not use this product

for any job except that for which it is intended.

DON’T OVERREACH - Guide the tiller/cultivator at a

walking pace only. Keep proper footing and balance

at all times.

LIGHTING - Only operate your tiller/cultivator in

daylight or good artificial light.

STORE IDLE UNIT INDOORS-When not in use, the

tiller/cultivator should be stored indoors in a dry area

out of children’s reach.

MAINTAIN UNIT WITH CARE-Keep clean for best

performance and to reduce the risk of injury. Inspect

extension cord periodically and replace if damaged.

Keep handles dry, clean and free from oil.

POLARIZED PLUGS-To reduce the risk of electric

shock, this product has a polarized plug. Polarized

connections will fit together only one way. Make

sure that the receptacle end of the extension cord

has large and small blade slot widths. If the plug

does not fit fully into the extension cord, reverse the

plug. If it still does not fit, obtain a suitable extension

cord. If the extension cord does not fit fully into the

outlet, contact a qualified electrician to install the

proper outlet. Do not change the plug on the tool or

the extension cord in any way.

Do not operate the tiller/cultivator on a slope that is

too steep for safe operation. When on slopes, slow

down and make sure you have good footing.

Before starting the tiller/cultivator make sure the

times are not touching any object and are free to

move.

Grip the guide bar firmly with both hands. Never

operate the tiller/cultivator with one hand.

CAUTION: The tiller/cultivator may bounce upward

and/or jump forward if the tines strike extremely

hard packed soil, frozen ground, or buried obstacles

such as large stones, roots or stumps.

GENERAL SAFETY

5

Model TC70010

4. Slide the cord retainer onto the center handle

section. (Fig. 2-3)

5. Attach the center handle section to the lower handle

sections using the two supplied M6 J-bolts and wing

nuts. (Fig. 2-4)

6. Fasten the upper handle section to the center handle

section using the two supplied M6 J-bolts and wing

nuts.(Fig. 2-5)

7. Use the two supplied cable clips to secure the cord to

the handle. (Fig. 2-6)

ASSEMBLY

This product must be assembled correctly before use.

1. Remove the screws (M5 X 12) and washers from

each end of the wheel frame axle. Assemble the

wheels onto the axle, then install washers and

screws (M5 X 12) to secure. (Fig. 2-1)

2. Press the hub caps into the wheels and cover the

ends of the axles. You may use a hammer to seat

them securely into the wheels. (Fig. 2-1)

3. To lower wheel frame, push the lock button on back

of motor housing to release the frame (Step A).

Lower the wheel frame (Step B) and pull out the lock

pin on lower handle section (Step C). Align lock pin

to the hole in wheel frame then release it to lock the

wheel frame in position. (Fig. 2-2)

WARNING: If any parts are damaged or missing do not

operate this product until the parts are replaced. Failure

to heed this warning could result in serious personal

injury. Call our customer service help line at

1-800-633-1501 for assistance.

WARNING: Do not connect to power supply until

assembly is complete. Failure to comply could result in

accidental starting and possible serious personal injury.

WARNING: Do not attempt to modify this product or

create accessories not recommended for use with this

product. Any such alteration or modification is misuse

and could result in a hazardous condition leading to

possible serious personal injury.

2

M5x12

M6

6

Model TC70010

ADJUSTABLE TINE ASSEMBLY INSTRUCTION

Tines are identified (A,B,C,D) with letters stamped into the Tine Hubs.

CHANGE FROM FOUR TINES TO TWO TINES

Lift the Lock Pin rings and remove Lock Pins at

both ends of the shaft. Remove Tine A and D

from the shaft. (Fig. 3)

CHANGE FROM TWO TINES TO FOUR TINES

Install Tine A and D onto the shaft as shown.

Ensure holes in Tine Hubs and shaft are aligned.

Insert Lock Pin into the through holes and pull

Lock pin ring downward to lock the Pin into place.

Be sure to install Tines as shown in Fig 3. Tines

cannot be secured if assembled in other

sequence of Tine position. (Fig. 3)

In the event the lock Pins are lost or misplaced,

Tines A and D may be secured using the extra

M8X40 Hex head bolts and M8 Lock nuts

provided. (Fig. 4)

3

4

WARNING: Before adjusting tine assembly,

disconnect power supply. Failure to heed this

warning could result in serious personal injury.

7

Model TC70010

OPERATING

STARTING:

Make sure the wheel frame is raised before you start

the tiller. To raise the frame, pull out the lock pin (Step

A); rotate the wheel frame upward, so that it snaps

beneath the lock button on the back of the motor

housing (Step B); release the lock pin. The wheel

frame will be locked in place by the lock button.

(See Fig. 5)

Secure the extension cord into the cord retainer. The

loop of the extension cord must be long enough for

the cord retainer to freely slide from one side to the

other. Plug the extension cord into the power cord

plug on the tiller. (See Fig. 6)

Move the tiller/cultivator to the work area prior to

starting the motor.

WARNING: Do not start tiller with any person or

object directly in its path.

Hold the tiller/cultivator firmly while starting. The tines

will pull the tiller/cultivator forward during operation.

Lower the tines slowly into the ground being tilled.

To start the tiller/cultivator, grip the center of the handle

firmly with your left hand. Using your right hand, push

the safety lock button on the switch box and hold to

allow activation of the switch control bail wire.

(See Fig. 7)

Use

your left thumb and index finger to maintain a firm grip

on the handle, and with remaining fingers pull the switch

control bail wire toward the handle. (See Fig. 8) Once

the unit has started, release the safety lock button.

Con-

tinue to hold the switch control bail wire against the tiller

handle as you cultivate. Use both hands to firmly grip the

handle to provide better control. (See Fig. 9)

To stop the tiller/cultivator simply release the bail wire.

6

5

7

8

9

8

Model TC70010

Use the tiller/cultivator for breaking sod, preparing

seed beds, and for cultivating gardens and flower

beds. The tiller/cultivator can also dig small holes for

planting saplings or potted plants.

For breaking sod or deep tilling, allow the tines to

pull the tiller/cultivator forward to the end of your

arm’s reach, then firmly pull it back toward yourself.

You will achieve the best results by repeatedly

allowing it to move forward and pulling it back.

By pulling the tiller/cultivator back towards yourself,

the tines will dig deeper and more aggressively.

To prevent tripping, take extra precautions when

moving backwards and when pulling the tiller/

cultivator back toward yourself.

If the tiller/cultivator digs deep enough to stay in one

spot, gently rock it side to side until it starts moving

forward again.

Never pass the tiller/cultivator over the extension

cord. Make sure the cord is always in a safe position

behind you.

When working on inclines always stand diagonally

to the incline to retain a firm, safe footing. Do not

work on extremely steep slopes.

For preparing seed beds, we recommend using one of

these tilling patterns:

Tilling Pattern A– Make two passes over area to be

tilled, the second at a right angle to the first.

Tilling Pattern B– Make two passes over area to be

tilled, the second overlapping the first.

Before use, remove any visible stones or other

foreign bodies from the area.

CAUTION: Before moving the tiller/cultivator from one

area to another switch off the motor and wait for the

tines to come to a complete stop. Be careful not to let

the tines touch the ground while moving the tiller/

cultivator. The tines as well as the unit itself may be

damaged even if the motor is switched off.

Clearing foreign objects:

During operation a stone or root could become lodged

in the tines, or tall grass or weeds may become

wrapped around the tine shaft. To clear the tines or

tine shaft release the trigger lever, wait for the tines to

come to a complete stop and unplug the tiller/

cultivator. Dislodge or remove the foreign matter from

the tines or tine shaft. To simplify removal of tall grass

or weeds from the tine shaft, remove one or more of

the tines. See Tine Removal and Installation.

OPERATING

9

Model TC70010

WARNING: Before carrying out maintenance operations, disconnect power supply.

Before each use check the extension cord for

signs of damage or ageing. Replace the cable if

it is cracked, split or otherwise damaged. Check the

condition of the tines and ensure that all threaded

connections are securely tightened. If the tines

become dull or blunt, sharpen or replace them. Call

our customer service help line at 1-800-633-1501

for assistance.

Once per season lubricate the tines and shaft. At

the end of the season, check the tiller/cultivator for

damage prior to storing. Repair or replace damaged

or broken parts.

CAUTION: Always clean the tiller/cultivator after

each use. Failure to carry out proper cleaning can

result in damage to the tiller/cultivator or result in

poor performance.

Clean the underside of the motor support plate and

housing around the tines with a scrub brush, and a

soft cloth dampened with a mild soap and water

mixture. Never use a water hose to clean the till-

er! To remove soil and debris from the transmission

and tines, use a stiff brush or a dampened cloth.

Clean the vents on the motor housing and remove

any remaining grass or dirt. Once cleaned, wipe the

tines and shaft dry and apply a light coat of oil to

prevent rust.

Tines maintenance: Worn tines invite poor

performance and overload of the motor. Check tines

before each use. Sharpen or replace the tine

assemblies with new ones when necessary. Call

1-800-633-1501 for assistance.

WARNING: Injury can occur while working on the

tines. Wear protective gloves.

Tine Removal and Installation (Fig. 10)

Lift the Lock Pin rings and remove the Lock Pins at

both ends of the shaft. Remove Tine A and D from

the shaft. Remove the M8x40 bolts and M8 Hex lock

nuts at both ends of the shaft. Remove Tine B and

C from the shaft. Reverse above steps to install

Tines.

Replace worn or damaged parts with original replace-

ment parts only. Parts from another tiller/cultivator may

not fit properly causing an unsafe situation.

Make sure all protective devices are secure and in

good condition. Repair or replace if necessary.

Lubrication (Fig. 11): The tines drive transmission

case has grease installed at the factory. It is not

required that the grease level be checked nor

recommended that grease be added during the first 2

years of use. After the second season of use, follow

the directions as described below:

Drain screw plugs are located on the right side of

transmission housing. Lay the tiller/cultivator on its left

side and clean the transmission of dirt and debris prior

to removing the drain screw plugs. If necessary,

remove tine assemblies to have better access to the

drain screw plug. Use a 5mm hex key to unscrew the

plugs.

Using a squeeze bottle or tube, add approximately 2.4

oz. (70ml) of auto gear lube. Do not overfill. When

completed, reinstall both drain screw plugs into the

transmission.

M10 X 6

 7.5 X  1.8

MAINTENANCE

11

10

Tine D

Tine C

Tine B

Tine A

10

Model TC70010

Store the Tiller/Cultivator in a dry, clean area out of reach

of children.

During extended periods of storage, ensure that the tiller/

cultivator is protected against corrosion and rust.

TROUBLESHOOTING

Problem Possible causes Remedy

Motor does not start Unit not plugged in

No electricity

Defective cable

Defective safety switch/plug

Overheat protection activated

Plug in the unit

Check power supply

Check cable. Repair or replace if required

Arrange for repair

1. Working depth too large, set to a shorter depth.

2. Blades blocked, remove the blockage.

3. Soil too hard, select correct work depth and move

forward and backward several times while slowing

down the operation speed.

Wait until the motor cools down for about 15 minutes

before further use.

Abnormal noises Blade is jammed

Lubrication running out

Bolts, nuts or other components are

loose.

Switch off . Wait till tines comes to a complete stop.

Remove jammed objects.

Tiller/cultivator must be repaired. Call our customer

service help line at 1-800-633-1501 for assistance.

Tighten all components. Arrange for repair if noises

continue.

Abnormal vibrations Blades damaged or worn

Working depth too large

Replace damaged or worn blades.

Set to correct working depth.

Poor results Working depth too small

Worn blades

Set to correct working depth.

Replace damaged or worn blades.

STORAGE

At the end of the season, or if the tiller/cultivator is not

being used for longer than a month, wipe over all metal

surfaces with an oil impregnated cloth to protect them

from corrosion or spray with a fine coat of oil. Fold the

upper handle down, and store the tiller/cultivator in a

suitable place.

11

Model TC70010

PARTS AND SERVICE

For parts or service, please call 1-800-633-1501 or visit us online at americanlawnmower.com. Be

sure to provide all relevant information when you call or visit.

REPAIR PARTS (KITS/ ITEMS)

The model/ serial number of this tool is found on a plate or label attached to the housing. Please

record the serial number in the space provided below.

MODEL NUMBER TC70010 ___

SERIAL NUMBER________________

Always mention the model number when ordering kits/items for this tool.

CALL US FIRST !!

Call us first with questions about operating or maintaining your tool

at 1-800-633-1501 between 8:00 a.m. – 5:00 p.m. Eastern

Standard Time, or get assistance on www.americanlawnmower.com.

12

Model TC70010

No. Kit/Item Number Description QTY

1 RTC700SET-adj Tine Kit 1

2 RTC10/16-U Upper Handle Kit 1

3 RTC10/16-C Center Handle 1

4 RTC10/16-HDW Handle Hardware Kit 1

13

Model TC70010

NOTES

__________________________________________________________________

In a continued commitment to improve quality, the Manufacturer reserves the right to

make component changes or design changes when necessary.

OWNER’S MANUAL

TC70010 Tiller/Cultivator

Rev. 10/21/2019

WARRANTY POLICY

Two (2) year limited warranty on Earthwise outdoor power equipment.

Earthwise warrants to the original owner that each new product and service part is free from defects in materials

and workmanship and agrees to repair or replace any defective product or part for the warranty period as stated

above from the original date of purchase except for the conditions and circumstances listed below:

This warranty applies only to the original purchaser at

retail and may not be transferred.

Warranty applies if the product is used for personal,

household or family use. Warranty is void if product is

used for commercial, industrial or rental purposes.

Warranty does not include repairs necessary due to

owner‘s abuse or negligence (including overloading the

product beyond capacity or immersion in water), or the

failure to assemble, operate, maintain or store the prod-

uct according to the instructions in the owner‘s manual.

This warranty is not transferable and only applies to

product sold directly from an authorized retailer. This

warranty does not apply to any product, new or used,

purchased through unauthorized third-party channels.

ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL

LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT

FROM ANY DEFECT, FAILURE OR MALFUNCTION

OF THE PRODUCT IS NOT COVERED BY THE

WARRANTY. Some states do not allow the exclusion or

limitation on how long an implied warranty lasts, so the

above limitation may not apply to you.

Products sold damaged or incomplete, sold “as is”, or

sold as reconditioned are not covered under the war-

ranty.

Damage or liability caused by shipping, improper

handling, improper assembly, incorrect voltage,

improper wiring, improper maintenance, improper

modification or the use of accessories and/or

attachments not specifically recommended is not

covered by this warranty.

Expendable items that become worn during normal use

are not covered by the warranty.

Warranty does not cover damage caused by cold, heat,

rain, excessive humidity, corrosive environments and

materials, or other contaminants.

Warranty does not include installation, assembly or

normal adjustments explained in the owner‘s manual.

The expense of delivering the product to the vendor and

the expense of returning the product or replacement

parts to the owner is not covered by the warranty.

The warranty does not cover normal deterioration of the

exterior finish, including but not limited to scratches,

dents, paint chips or any corrosion or discoloration

caused by heat, abrasive and chemical cleaners.

Proof of purchase, original dated sales receipt, must accompany all warranty claims.

American Lawn Mower Company

The Great States Corporation

830 Webster Street

Shelbyville, IN 46176 USA

Phone 1-800-633-1501

www.americanlawnmower.com

Modelo TC70010

MANUAL DEL PROPIETARIO

Rotocultivador

GUARDE ESTE MANUAL PARA CONSULTAS FUTURAS

Este producto fue diseñado y fabricado de acuerdo con nuestros altos estándares de confiabilidad, facilidad de operación y

seguridad para el operario. Si se trata con cuidado, esta herramienta le otorgará años de óptimo rendimiento y resistencia.

ADVERTENCIA: Para reducir el riesgo de sufrir alguna lesión, el usuario debe leer y comprender el

manual del propietario antes de usar este producto.

NO DEVUELVA ESTE PRODUCTO A LA TIENDA. ¿TIENE PREGUNTAS SOBRE FUNCIONAMIENTO,

MONTAJE, PIEZAS O SERVICIO TÉCNICO? IR A WWW.AMERICANLAWNMOWER.COM O LLAME AL

1-800-633-1501 ENTRE LAS 8:00 AM Y LAS 5:00 PM, HORA DEL ESTE DE LOS ESTADOS UNIDOS.

Muchas gracias por su compra.

ESPECIFICACIONES DEL PRODUCTO

Modelo: TC70010

Voltaje del suministro eléctrico: 120V-60HZ Ancho de trabajo: 18 u 28 cm (7 u 11 pulg.)

Velocidad de las púas: 350 RPM Profundidad máx. de trabajo: 20 cm (8 pulg.)

Consumo de potencia: 10 amperios

Especificaciones del producto ....................................... 2

Símbolos ....................................................................... 3

Advertencias de seguridad ....................................... 4 - 5

Montaje .................................................................... 6 - 7

Funcionamiento ....................................................... 8 - 9

Mantenimiento ............................................................. 10

Almacenamiento .......................................................... 11

Solución de problemas ................................................ 11

Garantía ...................................................................... 12

ÍNDICE

1

N.°

Descripción (N.º de pieza)

N.°

Descripción (N.º de pieza)

1

Mango superior (RTC70010-01)

11

Tapa del cubo de la rueda (RTC70010-60)

2

Gatillo (RTC70010-17)

12 Pasador de bloqueo (RTC70010-10)

3

Conjunto de cable de alimentación e interruptor (RTC70010-02)

13 Caja del motor (RTC70010-22)

4

Sujetador de cable (RTC70010-03)

14

Escudo protector (RTC70010-33)

5 Retenedor de cable (RTC70010-04) 15

Púa D (RTC70010-42)

6

Tuerca mariposa (RTC70010-05)

16

Púa C (RTC70010-43)

7

J-perno M6 (RTC70010-06)

17

Púa B (RTC70010-55)

8

Mango central (RTC70010-07)

18

Púa A (RTC70010-56)

9

Mango inferior - II (RTC70010-16)

19

Pasador de bloqueo (RTC70010-50)

10

Mango inferior - I (RTC70010-09)

20

Rueda (RTC70010-62)

2

Modelo TC70010

Precauciones para su seguridad.

Lea el manual de instrucciones y atienda las instrucciones de seguridad y advertencia.

¡DESCONECTAR! Retire el enchufe del tomacorriente de inmediato si el cable está

dañado o cortado.

¡DESCONECTAR! Retire el enchufe del tomacorriente antes de realizar una limpieza

o un mantenimiento.

No trabaje en condiciones de humedad.

Use protecciones para sus ojos y oídos.

Mantenga a las personas que se encuentran en el lugar a una distancia segura.

¡PELIGRO! Cuchillas giratorias. Mantenga manos y pies a una distancia segura.

¡PELIGRO! Puede ser golpeado por objetos despedidos.

Los desechos de los productos eléctricos no se deben eliminar con los desechos domésticos.

Recicle donde haya centros para tal fin. Consulte a la autoridad local o al distribuidor minorista

para obtener asesoramiento sobre reciclado.

SÍMBOLOS

Algunos de los siguientes símbolos pueden aparecer en este producto. Tenga a bien estudiarlos y aprender su significado.

La adecuada interpretación de estos símbolos le permitirá operar el producto mejor y de manera más segura.

3

Modelo TC70010

PARA REDUCIR EL RIESGO DE LESIONES: Antes de

utilizar este producto, cerciórese de que todos los usuarios

lean y comprendan las instrucciones de seguridad y la demás

información incluida en este manual.

PRECAUCIÓN: Use protección auditiva apropiada

mientras trabaja. En ciertas condiciones y con cierta

duración de uso, el ruido generado por este producto puede

contribuir a la pérdida de la audición.

Guarde estas instrucciones y revíselas con frecuencia

antes de usar la herramienta y para impartirlas a otros.

ADVERTENCIA: Al utilizar aparatos eléctricos para el

jardín, se recomienda respetar las precauciones de

seguridad básicas que se detallan a continuación, a fin

de reducir riesgos de incendios, descargas eléctricas y

lesiones personales.

LEA TODAS LAS INSTRUCCIONES

VERIFIQUE LAS PIEZAS DAÑADAS. Antes de seguir

usando el producto, se deberán revisar las piezas

dañadas en forma exhaustiva para determinar si la

herramienta funcionará correctamente y realizará el

trabajo previsto. Compruebe la alineación y las

uniones de las piezas móviles, el montaje, averías

de componentes y otros factores que puedan afectar

el funcionamiento. Se debe reparar o reemplazar

cualquier pieza dañada en forma adecuada. Para

recibir asistencia, comuníquese con nuestra línea de

ayuda de atención al cliente al 1-800-633-1501.

EVITE AMBIENTES PELIGROSOS. No utilice

este producto en condiciones de lluvia o tormenta

ni en lugares húmedos o mojados. Tampoco trabaje

en entornos donde existan gases o sustancias

explosivas. Por lo general, los motores de estos

productos producen chispas que podrían inflamar

los gases.

MANTENGA ALEJADOS A LOS NIÑOS. Todos los

visitantes, niños y mascotas deben mantenerse a

una distancia segura de la zona de trabajo.

USE ROPA ADECUADA. No use prendas sueltas ni

artículos de joyería. Use protección para cubrir y

contener el cabello largo ya que puede quedar

atrapado en las piezas móviles. Se recomienda usar

guantes de goma y calzado resistente cuando se

trabaja al aire libre.

USE GAFAS DE SEGURIDAD. Al trabajar con este

producto, use gafas de seguridad con protectores

laterales que cumplan con la norma ANSI Z87.1.

Protéjase la cara con una mascarilla antipolvo si

hay polvo en el ambiente.

DOBLE AISLAMIENTO. El rotocultivador tiene

doble aislamiento. Es decir que todas las piezas

metálicas externas están aisladas del suministro

eléctrico. Esto se logra con la introducción de una

capa de aislamiento entre las piezas eléctricas y las

mecánicas. El doble aislamiento le garantiza la

mayor seguridad posible.

CABLE DE EXTENSIÓN. Asegúrese de que el

cable de extensión esté en buenas condiciones.

Además, compruebe que tenga el grosor suficiente

para transportar la corriente que necesitará el

producto. Un cable de extensión muy pequeño

provocará una disminución en la tensión de la línea

y, como resultado, una pérdida de potencia y

recalentamiento. La siguiente tabla muestra el

tamaño correcto que se debe usar según la longitud

del cable y el amperaje de la etiqueta. Ante la duda,

utilice el siguiente calibre más grueso. Cuanto más

bajo es el número de calibre, más grueso es el cable.

ADVERTENCIA: Para el exterior, use cables de

extensión rotulados con las siguientes inscripciones:

SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJTWA o

SJTOWA. Estos cables están especificados para

usar al aire libre y reducir el riesgo de descarga

eléctrica.

El cable de extensión y el cable de

alimentación se pueden atar para

evitar que se desconecten durante

el uso. Realice el nudo como se

muestra en la imagen y luego

conecte el enchufe del cable de alimentación en el

receptáculo del cable de extensión. Este método

también se puede aplicar para unir dos cables de

extensión.

Tenga presente el cable de extensión mientras opera

el rotocultivador. Tenga cuidado de no tropezar con el

cable. Mantenga el cable alejado de las púas.

PROTECCIÓN CONTRA RECALENTAMIENTO.

Si el rotocultivador queda bloqueado por un objeto

extraño o si el motor se sobrecarga, el motor se

apagará automáticamente mediante el dispositivo

de protección. Suelte la palanca del gatillo y espere

a que el motor se enfríe (aprox. 15 minutos) antes

de arrancar el rotocultivador nuevamente.

ADVERTENCIAS DE SEGURIDAD IMPORTANTES

NORMAS GENERALES DE SEGURIDAD

Calibre mínimo para los cables

Voltios Longitud total del cable en pies

120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300

Amperaje

Más No más Calibre AWG

de de

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 No se recomienda

4

Modelo TC70010

PONGA ATENCIÓN. Observe lo que está haciendo.

Use el sentido común. No opere el rotocultivador si

está cansado o bajo la influencia de drogas o

medicamentos.

ADVERTENCIA: No trabaje con el rotocultivador

cerca de cables eléctricos, líneas telefónicas,

tuberías o mangueras subterráneas.

Si el rotocultivador golpea un cuerpo extraño,

apáguelo de inmediato, espere a que las púas se

detengan y verifique si hay daños. Si fuera

necesario, repare las piezas dañadas antes de

volver a poner en marcha la herramienta.

Si el rotocultivador comienza a vibrar de manera

inusual, apáguelo de inmediato y revíselo para

detectar la causa. Generalmente, la vibración

advierte la existencia de un problema.

PELIGRO: RIESGO DE CORTES. Use guantes

y sea prudente cuando limpie o realice el

mantenimiento al rotocultivador.

Siempre apáguelo; desconéctelo del suministro

eléctrico y espere hasta que las púas se detengan

por completo antes de realizar tareas de

mantenimiento o reparaciones.

PRECAUCIÓN: Las púas no se detienen de

inmediato cuando se apaga el rotocultivador.

PRECAUCIÓN: Riesgo de lesiones. No acerque

ninguna parte de su cuerpo, ni prendas de vestir a

las púas giratorias.

ADVERTENCIA: Proposición 65 de California:

Este producto contiene sustancias químicas al

estado de California como causantes de cáncer,

defectos de nacimiento u otros problemas

reproductivos .

ADVERTENCIA: Cáncer y Daño Reproductivo -

www.P65Warnings.ca.gov.

ADVERTENCIA: Parte del polvo y los desechos

generados por el uso de esta herramienta

contienen químicos reconocidos por el Estado de

California como causantes de cáncer, defectos de

nacimiento u otros efectos nocivos para el aparato

reproductor. Algunos ejemplos de estos productos

químicos son:

- químicos presentes en fertilizantes

- compuestos presentes en insecticidas,

herbicidas y pesticidas

- arsénico y cromo de maderas tratadas

químicamente

El riesgo que usted corre al exponerse a estos

químicos varía según la frecuencia con la que

realiza este tipo de trabajo. Para reducir la

exposición, trabaje en una zona bien ventilada y

utilice equipo de protección aprobado, como

mascarillas antipolvo especialmente diseñadas

para filtrar partículas microscópicas.

INTERRUPTOR DE CIRCUITO POR FALLA A TIERRA

(ICFT). El circuito o tomacorriente que se usen para

el rotocultivador deben contar con esta protección.

Se puede utilizar uno de los receptáculos que

tengan la protección de ICFT incorporada.

DESCONECTE LA UNIDAD del suministro eléctrico

cuando no esté en uso o durante el servicio de

mantenimiento o la limpieza. Manténgala bajo

vigilancia constante.

NO MALTRATE EL CABLE. Nunca tire del cable

para trasladar este producto ni para desconectarlo

del receptáculo. Aleje el cable del calor, el aceite y

los bordes filosos.

USE LA HERRAMIENTA CORRECTA. No utilice este

producto en trabajos para los que no esté indicado.

NO ADOPTE UNA POSTURA INCÓMODA. Guíe el

rotocultivador sólo a paso de hombre. Mantenga una

base de apoyo firme y buen equilibrio en todo momento.

ILUMINACIÓN. Trabaje con el rotocultivador sólo

con luz natural o buena luz artificial.

GUARDE LA UNIDAD BAJO TECHO. Cuando no esté

en uso, el rotocultivador se deberá guardar en un lugar

cerrado y seco, fuera del alcance de los niños.

PRESTE ATENCIÓN AL MANTENIMIENTO DE LA

UNIDAD. Consérvela limpia para lograr un óptimo

funcionamiento y reducir el riesgo de lesiones.

Inspeccione el cable de extensión periódicamente y

reemplácelo si está dañado. Mantenga los mangos

secos, limpios y libres de aceite.

ENCHUFES POLARIZADOS. Para reducir el riesgo

de descarga eléctrica, este producto tiene un

enchufe polarizado. Las conexiones polarizadas

encajan de una sola manera. Cerciórese de que el

extremo del receptáculo del cable de extensión

tenga ranuras de anchos diferentes para los contactos.

Invierta el enchufe si no encaja totalmente en el cable

de extensión. Si aún así no encaja, consiga un cable

de extensión adecuado. Si el cable de extensión no se

adapta bien al tomacorriente, llame a un electricista

competente para que instale un tomacorriente

adecuado. No cambie el enchufe de la herramienta

ni el cable de extensión de ningún modo.

Para un funcionamiento seguro, no utilice el

rotocultivador en pendientes demasiado pronunciadas.

Cuando trabaje en pendientes, disminuya la velocidad

y asegúrese de tener una buena base de apoyo.

Antes de encender el rotocultivador, cerciórese de

que las púas no estén en contacto con ningún

objeto y de que tengan libre movimiento.

Sujete la barra guía con ambas manos y con firmeza.

No debe sujetarla nunca con una sola mano.

PRECAUCIÓN: El rotocultivador puede rebotar hacia

arriba o saltar hacia delante si las púas golpean suelo

muy compactado o congelado, u obstáculos

enterrados, como piedras grandes, raíces o tocones.

NORMAS GENERALES DE SEGURIDAD

5

Modelo TC70010

4. Deslice el retenedor de cable en el mango central. (Fig. 2-3)

5. Conecte el mango central al mango inferior utilizando los

dos J-pernos M6 y las tuercas mariposa que se

suministran. (Fig. 2-4)

6. Ajuste el mango superior al mango central utilizando los

dos J-pernos M6 y las tuercas mariposa que se

suministran. (Fig. 2-5)

7. Utilice los dos sujetadores de cable suministrados para

sujetar el cable. (Fig. 2-6)

MONTAJE

Este producto debe ser montado correctamente antes de su

uso.

1. Retire los tornillos (M5 X 12) y arandelas del bastidor de las

ruedas. Inserte las ruedas en el eje del bastidor, luego fije las

arandelas y los tornillos (M5 X 12). (Fig. 2-1)

2. Coloque las cubiertas de las ruedas en las ruedas y cubra los

extremos de los ejes. Puede usar un martillo para asentar

bien las cubiertas. (Fig. 2-1)

3. Para bajar el bastidor de las ruedas, oprima el botón de

bloqueo que se encuentra en la parte trasera de la caja del

motor para soltar el bastidor (Paso A). Baje el bastidor de las

ruedas (Paso B) y tire del pasador de bloqueo que se

encuentra en el mango inferior (Paso C). Alinee el pasador de

bloqueo con el orificio del bastidor de las ruedas, luego

suéltelo para trabar el bastidor en posición. (Fig. 2-2)

ADVERTENCIA: Si alguna pieza falta o está dañada, no utilice

este producto hasta reponer la pieza en cuestión. De lo

contrario, podría sufrir lesiones personales de gravedad.

Comuníquese con nuestra línea de ayuda de atención al

cliente al 1-800-633-1501 para recibir asistencia.

ADVERTENCIA: No conecte la herramienta al suministro

eléctrico hasta finalizar el montaje. De lo contrario, la

máquina podría arrancar accidentalmente y provocar

lesiones personales de gravedad.

ADVERTENCIA: No intente modificar la unidad ni elaborar

accesorios no recomendados para usar con este producto. Dicha

clase de alteración o modificación constituye un uso inadecuado

de la herramienta y podría generar situaciones de riesgo y

provocar lesiones personales de gravedad.

2

Mango

central

Mango

central

Mango

central

Mango

superior

M5x12

M6

6

Modelo TC70010

La page est en cours de chargement...

EarthWise TC70010 Le manuel du propriétaire

EarthWise TC70010 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents