IKEA ISE630VS11 Le manuel du propriétaire

Marque: IKEA

Modèle: ISE630VS11

Catégorie: Cuisinières

Taper: Le manuel du propriétaire

for

| E,A ®

WHIRLPOOL

CORPORATION

ELECTRICRANGE

For questions about features, operation/performance,

parts, accessories or service, call: 1-800-253-1301.

or visit our website at www.ikea.com

In Canada, call for assistance, installation or service, call: 1-800-807-6777

or visit our website at www.ikea.ca

CUISINII:REf:LECTRIQUE

Gude d utitisciton et d en!_'eI'en

Au Canada, pour assistance, installation ou service, composer le 1-800-807-6777

ou visitez notre site Web www.ikea.ca

Table of Contents/Table des matieres ........................................ 2

W10184782A

TABLEOF CONTENTS

RANGE SAFETY ............................................................................. 3

The Anti-Tip Bracket .................................................................... 3

COOKTOP USE .............................................................................. 5

Cooktop Controls ......................................................................... 5

Ceramic Glass .............................................................................. 5

Home Canning ............................................................................. 6

Coo kware ..................................................................................... 6

ELECTRONIC OVEN CONTROL ................................................... 7

Display .......................................................................................... 7

Cancel .......................................................................................... 7

Clock ............................................................................................ 7

Timer............................................................................................. 7

Control Lock................................................................................. 8

Oven Temperature Control .......................................................... 8

OVEN USE ....................................................................................... 8

Aluminum Foil............................................................................... 8

Positioning Racks and Bakeware ................................................ 8

Bakeware ...................................................................................... 9

Oven Vent ..................................................................................... 9

Baking ........................................................................................... 9

Cook & Hold ............................................................................... 10

Keep Warm ................................................................................. 10

Broiling ........................................................................................ 10

Automatic Shut-Off/Sabbath Mode ........................................... 11

RANGE CARE ............................................................................... 12

Self-Cleaning Cycle .................................................................... 12

General Cleaning ........................................................................ 13

Oven Light .................................................................................. 14

Storage Drawer (on some models) ............................................ 15

Oven Door .................................................................................. 15

TROUBLESHOOTING .................................................................. 15

ASSISTANCE OR SERVICE ......................................................... 16

In the U.S.A................................................................................ 16

In Canada ................................................................................... 16

WARRANTY .................................................................................. 17

TABLEDESMATIERES

SI_CURITI_ DE LA CUISINII=RE ................................................... 18

La bride antibasculement ........................................................... 18

UTILISATION DE LA TABLE DE CUlSSON ................................ 21

Commandes de latable de cuisson .......................................... 21

Vitroceramique (sur certains modeles) ....................................... 22

Preparation de conserves &la maison ....................................... 23

Ustensiles de cuisson ................................................................ 23

COMMANDE I_LECTRONIQUE DU FOUR ................................. 24

Afficheur ..................................................................................... 24

Cancel (annulation)..................................................................... 24

Horloge ....................................................................................... 24

Minuterie ..................................................................................... 24

Verrouillage des commandes ..................................................... 25

Commande de la temperature du four ...................................... 25

UTILISATION DU FOUR ............................................................... 25

Papier d'aluminium ..................................................................... 25

Positionnement des grilles et des ustensiles de cuisson .......... 26

Ustensiles de cuisson ................................................................ 26

#vent du four .............................................................................. 27

Cuisson au four .......................................................................... 27

Cuisson et maintien au chaud .................................................... 27

Maintien au chaud ...................................................................... 28

Cuisson au gril............................................................................ 28

Arr_t automatique/Mode Sabbat ............................................... 29

ENTRETIEN DE LA CUlSINII_RE ................................................. 30

Programme d'autonettoyage (sur certains modeles) ................ 30

Nettoyage gen6ral ...................................................................... 31

Lampe du four ............................................................................ 33

Tiroir de remisage ....................................................................... 33

Porte du four ............................................................................... 33

DI_PANNAGE ................................................................................. 33

ASSISTANCE OU SERVICE ......................................................... 35

Au Canada .................................................................................. 35

GARANTIE ..................................................................................... 35

RANGESAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without

having the anti-tip bracket fastened down properly.

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

See the installation instructions for details.

Failure to follow these instructions can result in death or serious burns to children and adults.

Anti-Tip

"'Bracket

Making sure the anti-tip bracket is installed:

• Slide range forward.

• Look for the anti-tip bracket securely attached to floor or wall.

• Slide range back so rear range foot is under anti-tip bracket.

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances

known to the State of California to cause cancer, birth defects, or other reproductive harm, and requires businesses to warn of

potential exposure to such substances.

WARNING: This product contains a chemical known to the State of California to cause cancer, birth defects, or other

reproductive harm.

This appliance can cause low-level exposure to some of the substances listed, including benzene, formaldehyde, carbon

monoxide, and toluene.

iMPORTANT SAFETY iNSTRUCTiONS

WARN(NG: To reduce the risk of fire, electrical shock,

injury to persons, or damage when using the range, follow

basic precautions, including the following:

[] WARNING: TO REDUCE THE RISK OF TIPPING OF

THE RANGE, THE RANGE MUST BE SECURED BY

PROPERLY INSTALLED ANTI-TIP DEVICES. TO CHECK

IF THE DEVICES ARE INSTALLED PROPERLY, SLIDE

RANGE FORWARD, LOOK FOR ANTI-TIP BRACKET

SECURELY ATTACHED TO FLOOR OR WALL, AND

SLIDE RANGE BACK SO REAR RANGE FOOT IS

UNDER ANTI-TIP BRACKET.

[] CAUTION: Do not store items of interest to children in

cabinets above a range or on the backguard of a range -

children climbing on the range to reach items could be

seriously injured.

[] Proper Installation - Be sure the range is properly installed

and grounded by a qualified technician.

[] Never Use the Range for Warming or Heating the Room.

[] Do Not Leave Children Alone - Children should not be left

alone or unattended in area where the range is in use.

They should never be allowed to sit or stand on any part of

the range.

[] Wear Proper Apparel - Loose-fitting or hanging garments

should never be worn while using the range.

[] User Servicing - Do not repair or replace any part of the

range unless specifically recommended in the manual. All

other servicing should be referred to a qualified technician.

[] Storage in or on the Range - Flammable materials should

not be stored in an oven or near surface units.

[] Do Not Use Water on Grease Fires - Smother fire or flame

or use dry chemical or foam-type extinguisher.

[] Use Only Dry Potholders - Moist or damp potholders on

hot surfaces may result in burns from steam. Do not let

potholder touch hot heating elements. Do not use a towel

or other bulky cloth.

[] DO NOT TOUCH SURFACE UNITS OR AREAS NEAR

UNITS - Surface units may be hot even though they are

dark in color. Areas near surface units may become hot

enough to cause burns. During and after use, do not touch,

or let clothing or other flammable materials contact surface

units or areas near units until they have had sufficient time

to cool. Among those areas are the cooktop and surfaces

facing the cooktop.

[] Use Proper Pan Size - The range is equipped with one or

more surface units of different size. Select utensils having

flat bottoms large enough to cover the surface unit heating

element. The use of undersized utensils will expose a

portion of the heating element to direct contact and may

result in ignition of clothing. Proper relationship of utensil to

burner will also improve efficiency.

[] Never Leave Surface Units Unattended at High Heat

Settings - Boilover causes smoking and greasy spillovers

that may ignite.

[] Make Sure Reflector Pans or Drip Bowls Are in Place -

Absence of these pans or bowls during cooking may

subject wiring or components underneath to damage.

[] Protective Liners - Do not use aluminum foil to line surface

unit drip bowls or oven bottoms, except as suggested in

the manual. Improper installation of these liners may result

in a risk of electric shock, or fire.

[] Glazed Cooking Utensils - Only certain types of glass,

glass/ceramic, ceramic, earthenware, or other glazed

utensils are suitable for range-top service without breaking

due to the sudden change in temperature.

[] Utensil Handles Should Be Turned Inward and Not Extend

Over Adjacent Surface Units - To reduce the risk of burns,

ignition of flammable materials, and spillage due to

unintentional contact with the utensil, the handle of a

utensil should be positioned so that it is turned inward, and

does not extend over adjacent surface units.

[] Do Not Soak Removable Heating Elements - Heating

elements should never be immersed in water.

[] Do Not Cook on Broken Cooktop - If cooktop should

break, cleaning solutions and spillovers may penetrate the

broken cooktop and create a risk of electric shock. Contact

a qualified technician immediately.

[] Clean Cooktop With Caution - If a wet sponge or cloth is

used to wipe spills on a hot cooking area, be careful to

avoid steam burn. Some cleaners can produce noxious

fumes if applied to a hot surface.

[] Use Care When Opening Door - Let hot air or steam

escape before removing or replacing food.

[] Do Not Heat Unopened Food Containers - Build-up of

pressure may cause container to burst and result in injury.

[] Keep Oven Vent Ducts Unobstructed.

[] Placement of Oven Racks - Always place oven racks in

desired location while oven is cool. If rack must be moved

while oven is hot, do not let potholder contact hot heating

element in oven.

[] DO NOT TOUCH HEATING ELEMENTS OR INTERIOR

SURFACES OF OVEN - Heating elements may be hot even

though they are dark in color. Interior surfaces of an oven

become hot enough to cause burns. During and after use,

do not touch, or let clothing or other flammable materials

contact heating elements or interior surfaces of oven until

they have had sufficient time to cool. Other surfaces of the

appliance may become hot enough to cause burns - among

these surfaces are oven vent openings and surfaces near

these openings, oven doors, and windows of oven doors.

For self-cleaning ranges -

[] Do Not Clean Door Gasket - The door gasket is essential

for a good seal. Care should be taken not to rub, damage,

or move the gasket.

[] Do Not Use Oven Cleaners - No commercial oven cleaner

or oven liner protective coating of any kind should be used

in or around any part of the oven.

[] Clean Only Parts Listed in Manual.

[] Before Self-Cleaning the Oven - Remove broiler pan and

other utensils.

For units with ventilating hood -

[] Clean Ventilating Hoods Frequently - Grease should not

be allowed to accumulate on hood or filter.

[] When flambeing foods under the hood, turn the fan on.

SAVE THESE INSTRUCTIONS

COOKTOP USE

H G F

OFF

\ /

A. Surface cooking area Iocator

B. Left front control knob

C. Left rear control knob

D. Right rear control knob

E.Right front control knob

F. Oven light

G. Hot surface indicator light

H. Electronic oven control

o®

LOW °oFF HIGH

©o

Fire Hazard

Turn off all controls when done cooking.

Failure to do so can result in death or fire.

The control knobs can be set anywhere between HIGH and LOW.

Push in and turn to setting. Use the following chart as a guide

when setting heat levels.

SETTING RECOMMENDED USE

HIGH

Medium High

8-10

Medium

5-7

Medium Low

2-4

LOW

• Start food cooking

• Bring liquid to a boil.

• Hold arapid boil.

• Quickly brown or sear food.

• Maintain a slow boil.

• Fry or saute foods.

• Cook soups, sauces and gravies.

• Stew or steam food.

• Simmer.

• Keep food warm.

• Melt chocolate or butter.

REMEMBER: When range is in use or (on some models)

during the Self-Cleaning cycle, the entire cooktop area may

become hot.

Hot Surface Indicator Light

The hot surface indicator light, located on the cooking surface,

will glow as long as any surface cooking area is too hot to touch,

even after the surface cooking area(s) is turned off.

C® slm c G csss

The surface cooking area will glow red when an element is on. It

may cycle on and off to maintain the selected heat level.

It is normal for the surface of light colored ceramic glass to

appear to change color when surface cooking areas are hot. As

the glass cools, it will return to its original color.

Cleaning off the cooktop before and after each use will help keep

it free from stains and provide the most even heating. On

cooktops with light colored ceramic glass, soils and stains may

be more visible, and may require more cleaning and care.

Cooktop cleaner and a cooktop scraper are recommended. For

more information, see "General Cleaning" section.

• Avoid storing jars or cans above the cooktop. Dropping a

heavy or hard object onto the cooktop could crack the

cooktop.

• To avoid damage to the cooktop, do not leave a hot lid on the

cooktop. As the cooktop cools, air can become trapped

between the lid and the cooktop, and the ceramic glass could

break when the lid is removed.

• For foods containing sugar in any form, clean up all spills and

soils as soon as possible. Allow the cooktop to cool down

slightly. Then, while wearing oven mitts, remove the spills

using a scraper while the surface is still warm. If sugary spills

are allowed to cool down, they can adhere to the cooktop

and can cause pitting and permanent marks.

• To avoid scratches, do not slide cookware or bakeware

across the cooktop. Aluminum or copper bottoms and rough

finishes on cookware or bakeware could leave scratches or

marks on the cooktop.

• Do not cook popcorn in prepackaged aluminum containers

on the cooktop. They could leave aluminum marks that

cannot be removed completely.

• To avoid damage to the cooktop, do not allow objects that

could melt, such as plastic or aluminum foil, to touch any part

of the entire cooktop.

• To avoid damage to the cooktop, do not use the cooktop as a

cutting board.

Usecookwareaboutthesamesizeasthesurfacecooking

area.Cookwareshouldnotextendmorethan1/2"(1.3cm)

outsidethearea.

_.....................B

A. Surface cooking area

B. Cookware/canner

C. 7/2"(1.3 cm) maximum overhang

• Use flat-bottomed cookware for best heat conduction and

energy efficiency. Cookware with rounded, warped, ribbed or

dented bottoms could cause uneven heating and poor

cooking results.

• Determine flatness by placing the straight edge of a ruler

across the bottom of the cookware. While you rotate the ruler,

no space or light should be visible between it and the

cookware.

• Cookware designed with slightly indented bottoms or small

expansion channels can be used.

• Make sure the bottoms of pots and pans are clean and dry

before using them. Residue and water can leave deposits

when heated.

To avoid damage to the cooktop, do not cook foods directly

on the cooktop.

When canning for long periods, alternate the use of surface

cooking areas, elements or surface burners between batches.

This allows time for the most recently used areas to cool.

• Center the canner on the grate or largest surface cooking

area or element. On electric cooktops, canners should not

extend more than 1/2"(1.3 cm) beyond the surface cooking

area or element.

• Do not place canner on 2 surface cooking areas, elements or

surface burners at the same time.

On ceramic glass models, use only flat-bottomed canners.

For more information, contact your local agricultural

department. Companies that manufacture home canning

products can also offer assistance.

IMPORTANT: Do not leave empty cookware on a hot surface

cooking area, element or surface burner.

Ideal cookware should have a flat bottom, straight sides and a

well-fitting lid, and the material should be of medium-to-heavy

thickness.

Rough finishes may scratch the cooktop or coil elements.

Aluminum and copper may be used as a core or base in

cookware. However, when used as a base they can leave

permanent marks on the cooktop or coil elements.

Cookware material is a factor in how quickly and evenly heat is

transferred, which affects cooking results. A nonstick finish has

the same characteristics as its base material. For example,

aluminum cookware with a nonstick finish will take on the

properties of aluminum.

Cookware with nonstick surfaces should not be used under the

broiler.

Use the following chart as a guide for cookware material

characteristics.

COOKWARE CHARACTERISTICS

Aluminum •

Cast iron

Ceramic or

Ceramic glass

Copper •

Earthenware •

Porcelain •

enamel-on-

steel or cast

iron

Stainless steel •

Heats quickly and evenly.

Suitable for all types of cooking.

Medium or heavy thickness is best for

most cooking tasks.

Heats slowly and evenly.

Good for browning and frying.

Maintains heat for slow cooking.

Follow manufacturer's instructions.

Heats slowly, but unevenly.

Ideal results on low to medium heat

settings.

Heats very quickly and evenly.

Follow manufacturer's instructions.

Use on low heat settings.

See stainless steel or cast iron.

Heats quickly, but unevenly.

A core or base of aluminum or copper

on stainless steel provides even

heating.

ELECTRONICOVEN CONTROL

A B C D

C_HOiO_&D&COOK&

K d I

A. Bake

B. Clock/timer display

C. More (+)/less (-) buttons

D. Timer

E.Cancel

F. Keep warm

G. Clock

H. Delay (on self-clean models)

When power is supplied to the range or after a power

interruption, the last clock time before power was interrupted will

flash.

Bake or Lock may flash rapidly in the display to alert you if there

is an error or problem. Press CANCEL and reset clock if needed.

When the oven is in use, the display shows the temperature and

oven setting.

When the oven is not in use, the display shows the time of day.

When using the TIMER, for settings of 1 to 59 minutes, the

display will count down in minutes. For settings of 1 hour or

more, the display will count down hours and minutes.

The CANCEL button stops any function except the Clock, Timer

and Control Lock. When you press the CANCEL button, the

display will show the time of day, or the time remaining if the

TIMER is being used.

The clock can be set to display time in a 12-hour or 24-hour

format. The clock is set at the factory for the 12-hour format.

To recall the time of day when another time function is showing,

press the Clock pad.

Clock time cannot be changed when the oven has been

programmed for Delay Cook, Clean, or Cook & Hold.

To Change the Clock to 24-hour Format:

1. Press and hold CANCEL and DELAY for 3 seconds.

2. Press the "up" or "down" arrow pad to select 24 hour.

I. Clean (on self-clean models)

J. Cook & hold

K. Broil

To Cancel the Clock Display:

If you do not want the time of day to display:

Press and hold CANCEL and CLOCK for 3 seconds, the time of

day will disappear from the display.

When the clock display is canceled, press CLOCK to briefly

display the time of day.

To Restore the Clock Display:

Press and hold CANCEL and CLOCK for 3 seconds. The time of

day will reappear in the display.

The Timer can be set in hours or minutes up to 99 hours and

59 minutes, and counts down the set time.

The Timer can be used independently of any other oven function.

It can also be set while another oven function is operating.

NOTE: The Timer does not start or stop the oven.

To Set:

1. Press TIMER.

"0:00" will appear in the display. The colon will flash.

2. Press the "up" or "down" arrow pads to set the length of

time.

3. Press TIMER again or wait 4 seconds. Time will begin

counting down.

When the set time ends, 1 long beep will sound.

To Cancel:

1. Press and hold TIMER for 3 seconds

2. Press TIMER and set time to 0:00.

To Set:

1. Press CLOCK. The colon will flash in the display.

2. Press the "up" or "down" arrow pads to set the time of day.

3. Press CLOCK or wait 4 seconds. The colon stops flashing.

TheControlLockshutsdownthecontrolpanelpads(buttons)to

preventunintendeduseoftheoven(s).

TheControlLockispresetunlocked,butcanbelocked.

Iftheoveniscurrentlyinuse,thecontrolscannotbelocked.

To Lock/Unlock Control:

Press and hold CANCEL and COOK & HOLD for 3 seconds

(Press the CANCEL pad first.) Repeat to unlock.

IMPORTANT: Do not use a thermometer to measure oven

temperature because opening the oven door and element or

burner cycling may give incorrect readings.

The oven provides accurate temperatures; however, it may cook

faster or slower than your previous oven, so the temperature

calibration can be adjusted. It can be changed in Fahrenheit or

Celsius.

A minus sign means the oven will be cooler by the displayed

amount. The absence of a minus sign means the oven will be

warmer by the displayed amount. Use the following chart as a

guide.

ADJUSTMENT °F COOKS FOOD

(ADJUSTMENT °C)

5° to 10°F (3° to 6°C) ...a little more

15° to 20°F (9° to 12°C) ...moderately more

25 °to 35°F (15° to 21°C) ...much more

-5° to -10°F (-3° to -6°C) ...a little less

-15 ° to -20°F (-9° to -12°C) ...moderately less

-25°F (-15°C) ...much less

To Adjust Oven Temperature Calibration:

1. Press BAKE.

2. Enter 550 ° by pressing the "up" arrow pad.

3. Press and hold BAKE pad for several seconds or until "0°''

appears in the display.

If the oven temperature was previously adjusted, the change

will be displayed. For example, if the oven temperature was

reduced by 15 degrees the display will show -15°.

4. Press the "up" or "down" arrow pads to adjust the

temperature. Each time a pad is pressed, the temperature

changes by 5 degrees.

5. The time of day will automatically reappear in the display.

You do not need to readjust the oven temperature if there is a

power failure or interruption. Broiling, Keep Warm and Cleaning

temperatures cannot be adjusted.

To Display Temperatures in °C instead of °F:

1. Press and hold the CANCEL and BAKE buttons for

3 seconds. A single beep will sound and the current setting

will be displayed.

If no change is made, the range will return to the existing

setting after 30 seconds.

2. Press the "up" or "down" arrow pad to change the setting.

Wait 5 seconds and the setting will be complete.

OVEN USE

Odors and smoke are normal when the oven is used the first few

times, or when it is heavily soiled.

IMPORTANT: The health of some birds is extremely sensitive to

the fumes given off. Exposure to the fumes may result in death to

certain birds. Always move birds to another closed and well-

ventilated room.

Aum Fo

IMPORTANT: To avoid permanent damage to the oven bottom

finish, do not line the oven bottom with any type of foil, liners or

cookware.

• On those models with bottom vents, do not block or cover

the oven bottom vents.

• For best cooking results, do not cover entire rack with foil

because air must be able to move freely.

• To catch spills, place foil on rack below dish. Make sure foil is

at least V2"(1.3 cm) larger than the dish and that it is turned

up at the edges.

IMPORTANT: To avoid permanent damage to the porcelain

finish, do not place food or bakeware directly on the oven door or

bottom.

RACKS

• Position racks before turning on the oven.

• Do not move racks with bakeware on them.

• Make sure racks are level.

To move a rack, pull it out to the stop position, raise the front

edge, then lift out. Use the following illustration and chart as a

guide.

2 ............i

FOOD RACK POSITION(S)*

Large roasts, turkeys, angel food, 1 or 2

bundt cakes, quick breads, pies

Yeast breads, casseroles, meat and 2

poultry

Cookies, biscuits, muffins, cakes 2 or 3

*On models with the CleanBake TM feature, foods may be placed

on a lower rack position.

BAKEWARE

Hot air must be able to circulate around food to cook evenly, so

allow 2" (5 cm) of space around bakeware and oven walls. Use

the following chart as a guide.

NUMBER OF POSITION ON RACK

PAN(S)

1 Center of rack.

2 Side by side or slightly staggered.

3 or 4 Opposite corners on each rack. Make sure

that no bakeware piece is directly over

another.

The bakeware material affects cooking results. Follow

manufacturer's recommendations and use the bakeware size

recommended in the recipe. Use the following chart as a guide.

BAKEWARE/ RECOMMENDATIONS

RESULTS

Light colored • Use temperature and time

aluminum recommended in recipe.

• Light golden crusts

• Even browning

Dark aluminum and

other bakeware with

dark, dull and/or

nonstick finish

• Brown, crisp

crusts

• May need to reduce baking

temperatures slightly.

• Use suggested baking time.

• For pies, breads and casseroles,

use temperature recommended in

recipe.

• Place rack in center of oven.

Insulated cookie

sheets or baking

pans

• Little or no bottom

browning

Stainless steel

• Light, golden

crusts

• Uneven browning

Stoneware/Baking

stone

• Crisp crusts

Ovenproof

glassware, ceramic

glass or ceramic

• Brown, crisp

crusts

• Place in the bottom third of oven.

• May need to increase baking time.

• Follow manufacturer's instructions.

• May need to reduce baking

temperatures slightly.

A. Oven vent

The oven vent releases hot air and moisture from the oven, and

should not be blocked or covered. Blocking or covering the vent

will cause poor air circulation, affecting cooking and cleaning

results. Do not set plastics, paper or other items that could melt

or burn near the oven vent.

The oven automatically regulates the heat levels and both the top

and bottom elements cycle on and off accordingly during preheat

and bake to maintain a precise temperature range for optimal

cooking results.

To Bake or Roast:

Before baking, position the racks according to the "Positioning

Racks and Bakeware" section.

1. Press BAKE. "BAKE" will flash and "000" will appear in the

display.

2. Press or press and hold the "up" or "down" arrow pad.

350°F (175°C) will appear when either pad is first pressed.

Press the "up" or "down" pads to raise or lower the

temperature in 5°F/5°C increments.

3. Press BAKE again or wait 4 seconds. Bake will stop flashing

and light in the display.

100° or the actual temperature will display. The temperature

will rise in 5° increments until the preset temperature is

reached.

For best results, allow oven to fully preheat.

When the set oven temperature is reached, 1 long beep will

sound.

To recall the set temperature during preheat, press the BAKE

pad.

To change the oven temperature during preheat, press BAKE

twice, then the "up" or "down" pads until the desired

temperature is displayed.

To change the oven temperature during cooking, press BAKE,

then the "up" or "down" pads until the desired temperature is

displayed.

When cooking is finished, press CANCEL.

Preheating

Preheat temperatures are affected by varying factors such as

room temperature and peak energy usage times. It is normal for

the temperature showing on the display and the actual oven

temperature to differ.

Coo< & 4oc

Food Poisoning Hazard

Do not let food sit in oven more than one hour before

or after cooking.

Doing so can result in food poisoning or sickness.

Cook & Hold allows the oven to be set to turn on at a certain time

of day, cook for a set length of time, followed by a 1-hour Keep

Warm cycle.

Delay start should not be used for food such as breads and

cakes because they may not bake properly. Do not use delayed

baking if oven is already hot.

To Set Cook & Hold:

1. Press COOK & HOLD. "BAKE" and "HOLD" will flash and

"000" appears in the display.

2. Press or press and hold the "up" or "down" arrow pad to

select atemperature. The oven temperature can be set from

170°F (77°C) to 550°F (288°C).

3. Press COOK & HOLD again or wait 4 seconds. "HOLD" will

flash and "000" appears in the display.

4. Press or press and hold the "up" or "down" arrow pad to

select an amount of time to bake. Bake Time can be set from

10 minutes to 11 hours and 59 minutes.

"BAKE" and "HOLD" and the baking time will appear in the

display. The baking time will start counting down.

When the cooking time has elapsed:

4 beeps will sound, "BAKE" will turn off and "HOLD," "WARM,"

and "170 °" will appear in the display.

After 1 hour in Hold Warm:

"End" will appear and the time of day will reappear.

To cancel Cook & Hold at any time:

Press CANCEL. Remove food from oven.

To Set a Delayed Cook & Hold cycle:

Before setting, make sure the clock is set to the correct time of

day. See "Clock" section.

1. Press DELAY. "DELAY" will flash and "00:00" appears in the

display.

2. Press the "up" or "down" arrow pad to set a delay time.

3. While "DELAY" is still flashing, press COOK & HOLD. "BAKE"

and "HOLD" will flash and "000" appears in the display.

4. Press the "up" arrow pad to set the baking temperature.

"00:00" and "HOLD" will flash. "BAKE" stays lit.

5. Press the "up" arrow pad to set the baking time. The Delay

time, "DELAY," "BAKE," and "HOLD" will appear in the

display.

When the Delay time has expired:

"DELAY" will turn off. "BAKE," "HOLD," and the baking time will

be displayed. Baking will begin.

To set a Delay when Cook & Hold has already been

programmed:

1. Press DELAY. "DELAY" will flash and "00:00" appears in the

display.

2. Press the "up" or "down" arrow pad to set a delay time. After

4 seconds, "DELAY" will stay lit as a reminder that a delayed

cooking cycle has been set.

When the Delay time has expired and the oven starts:

The baking time will be displayed. "DELAY" will turn off and

"BAKE" and "HOLD" will remain lit.

To cancel:

Press CANCEL. All timed and untimed cooking functions will be

canceled. The time of day will reappear in the display.

Food Poisoning Hazard

Do not let food sit in oven more than one hour before

or after cooking.

Doing so can result in food poisoning or sickness.

IMPORTANT: Food must be at serving temperature before

placing it in the warmed oven. Food may be held up to 1 hour;

however, breads and casseroles may become too dry if left in the

oven during Keep Warm.

Follow manufacturer's recommendations when warming empty

serving bowls and plates.

To Set Keep Warm:

1. Press KEEP WARM. "WARM" flashes and "000" will appear in

the display.

2. Press or press and hold the "up" or "down" arrow pad to

select a temperature. "170 °,' will light when either pad is first

pressed.

The Keep Warm temperature can be set from 145°F (60°C) to

190°F (90°C).

"WARM" and the temperature will be displayed while Keep Warm

is active.

To cancel Keep Warm:

Press CANCEL. Remove food from oven.

Broiling uses direct radiant heat to cook food. Changing the

temperature when broiling allows more precise control when

cooking. The lower the temperature, the slower the cooking.

Thicker cuts and unevenly shaped pieces of meat, fish and

poultry may cook better at lower broiling temperatures.

• For best results, use a broiler pan and grid (provided on some

models). They are designed to drain juices and help avoid

spatter and smoke.

If you would like to purchase a broiler pan, one may be

ordered. See "Assistance or Service" section to order. Ask for

Part Number 4396923.

• For proper draining, do not cover the grid with foil. The

bottom of the pan may be lined with aluminum foil for easier

cleaning.

• Trim excess fat to reduce spattering. Slit the remaining fat on

the edges to avoid curling.

• Pull out oven rack to stop position before turning or removing

food. Use tongs to turn food to avoid the loss of juices. Very

thin cuts of fish, poultry or meat may not need to be turned.

• After broiling, remove the pan from the oven when removing

the food. Drippings will bake on the pan if left in the heated

oven, making cleaning more difficult.

Before broiling, position rack according to the Broiling Chart.

Preheat broil about 4 minutes. Position food on grid in the broiler

pan, then place it in the center of the oven rack. Leave the door

open about 4" (10.0 cm) (the first broil stop).

To Broil:

1. Press BROIL. "BROIL" flashes and "SEt" appears in the

display.

2. Press the "up" arrow pad to set HI Broil or press the "down"

arrow pad to set LO Broil. "HI" or "LO" will be displayed.

Select HI Broil (550°F/288°C) for normal broiling or LO Broil

(450°F/232°C) for low-temperature broiling.

After 4 seconds, the oven will start. "BROIL" will remain lit.

3. Press CANCEL when finished broiling.

BROILING CHART

For best results, place food 3" (7.0 cm) or more from the broil

element. Times are guidelines only and may need to be adjusted

for individual tastes. Recommended rack positions are numbered

from the bottom (1) to the top (5). For diagram, see the

"Positioning Racks and Bakeware" section.

FOOD RACK APPROXIMATE

POSITION TIME (minutes)

Steak

1" (2.5 cm) thick

medium 4 15-18

well-done 4 19-23

Ground meat patties

3/4"(2 cm) thick

well-done 4 15-18

Pork chops

1" (2.5 cm) thick

well-done 4 22-26

Ham slice, precooked

1/2"(1.25 cm) thick

warm 4 8-12

Bacon

well-done 4 6-10

Chicken

bone-in pieces LO Broil

well-done 3 or 4 28-38

Fish Fillets

flaky 4 8-12

Fish Steaks

1" (2.5 cm) thick

flaky 4 10-15

The oven will automatically turn off after 12 hours if you

accidentally leave it on. This feature can be turned off to enable

Sabbath Mode.

• Sabbath Mode can be turned on at any time with or without

the oven on.

• Sabbath Mode cannot be turned on if the touchpads are

locked out or when the door is locked.

• If the oven is baking when Sabbath Mode is set, "BAKE" will

go out at the end of the baking cycle however, the Bake

mode will remain active. There will be no audible beeps.

• If the oven light is desired while in Sabbath Mode, it must be

turned on before the Sabbath Mode is started.

• When the Sabbath Mode is started, no preheat beep will

sound.

• All prompts, messages and beeps are deactivated when

Sabbath Mode is active.

• The automatic door lock does not operate during the

Sabbath Mode.

• Pressing Cancel will cancel a Bake cycle, however the control

will stay in the Sabbath Mode.

• If power fails, the oven will power up in Sabbath Mode with

72 hours remaining and no cycle active.

To cancel the 12-hour shut-off and run the oven continuously

for 72 hours (Sabbath Mode):

1. Set the oven to Bake. See "Baking" section.

2. Press and hold CLOCK for 5 seconds.

"SAb" will be displayed and flash for 5 seconds.

"SAb" will then be displayed continuously until turned off or

until the 72-hour time limit is reached.

BAKE will also be displayed if a bake cycle is in use while the

oven is in Sabbath Mode.

BAKE is the only function that operates during the Sabbath

Mode. All other functions (Timer, Keep Warm, Clean, etc.) are

locked out during the Sabbath Mode.

To cancel Bake when in Sabbath Mode:

1. Press CANCEL.

BAKE will turn off in the display. No beeps will sound.

To cancel the Sabbath Mode:

1. Press and hold CLOCK for 5 seconds

2. After 72 hours, the Sabbath Mode will end.

"SAb" will flash for 5 seconds. The time of day will return to

the display.

RANGECARE

Burn Hazard

Do not touch the oven during the Self-Cleaning cycle.

Keep children away from oven during

Self-Cleaning cycle.

Failure to follow these instructions can result in burns.

IMPORTANT: The health of some birds is extremely sensitive to

the fumes given off during the Self-Cleaning cycle. Exposure to

the fumes may result in death to certain birds. Always move birds

to another closed and well-ventilated room.

Self-clean the oven before it becomes heavily soiled. Heavy soil

results in longer cleaning and more smoke.

Keep the kitchen well-ventilated during the Self-Cleaning cycle to

help get rid of heat, odors, and smoke.

Do not block the oven vent(s) during the Self-Cleaning cycle. Air

must be able to move freely. Depending on your model, see

"Oven Vent" or "Oven Vents" section.

Do not clean, rub, damage or move the oven door gasket. The

door gasket is essential for a good seal.

Prepare Oven:

• Remove the broiler pan, grid, cookware and bakeware and,

on some models, the temperature probe from the oven.

Remove oven racks to keep them shiny and easy to slide.

See "General Cleaning" section for more information.

• Remove any foil from the oven because it may burn or melt,

damaging the oven.

• Hand clean inside door edge and the 11/2"(3.8 cm) area

around the inside oven cavity frame, being certain not to

move or bend the gasket. This area does not get hot enough

during self-cleaning to remove soil. Do not let water, cleaner,

etc. enter slots on door frame. Use a damp cloth to clean this

area.

Wipe out any loose soil to reduce smoke and avoid damage.

At high temperatures, foods react with porcelain. Staining,

etching, pitting or faint white spots can result. This will not

affect cooking performance.

Prepare Cooktop and Storage Drawer:

• Remove plastic items from the cooktop because they may

melt.

• Remove all items from the storage drawer.

How the Cycle Works

IMPORTANT: The heating and cooling of porcelain on steel in the

oven may result in discoloring, loss of gloss, hairline cracks and

popping sounds.

The Self-Cleaning cycle uses very high temperatures, burning soil

to a powdery ash.

The oven is preset for a 3 hour clean cycle, however the time can

be changed. Suggested clean times are 2 hours for light soil and

between 3 hours and 4 hours for average to heavy soil.

Once the oven has completely cooled, remove ash with a damp

cloth. To avoid breaking the glass, do not apply a cool damp

cloth to the inner door glass before it has completely cooled.

The oven light will not work during the Self-Cleaning cycle.

When "LOCK" shows in the display, the door cannot be opened.

To avoid damage to the door, do not force the door open when

"LOCK" is displayed.

To Self-Clean:

1. Close the oven door.

2. Move the door lock lever to the right to the locked position.

3. Press CLEAN.

4. Press the "up" or "down" arrow pad.

CL-M (Clean - Medium soil, 3 hours) appears in the display.

If the door is not closed, beeps will sound and "door" will

appear in the display until the door is closed and the Clean

pad is pressed again. If the door is not closed within

45 seconds, the self-cleaning operation will be canceled

and the display will return to the time of day.

If more than 5 seconds elapse between pressing the Clean

pad and the "up" or "down" arrow pad, the program will

automatically return to the previous display.

5. To choose a clean setting other then Medium, press the "up"

or "down" arrow pads to scroll through the self-cleaning

settings.

CL-H (Clean - Heavy soil, 4 hours)

CL-M (Clean - Medium soil, 3 hours)

CL-L (Clean - Light soil, 2 hours)

Choosing a cleaning level automatically programs the self-

cleaning time.

6. After 4 seconds, the oven will start cleaning.

"LOCK" and "CLEAN" will appear in the display. The cleaning

time will count down in the display.

To Delay Start Self-Clean:

Before delay starting Self-Clean, make sure the door is closed

completely or it will not lock and the cycle will not begin.

1. Press DELAY.

"DELAY" flashes and "00:00" will appear in the display.

2. Press the "up" or "down" arrow pads to enter the amount of

time you want to delay the cycle. Delay time can be set from

10 minutes (00:10) to 11 hours and 59 minutes (11:59).

3. While "DELAY" is flashing, press the CLEAN pad. "CLEAN"

will flash in the display.

4. Press the "up" or "down" arrow pad.

CL-M (Clean - Medium soil, 3 hours) appears in the display.

5. To choose a clean setting other then Medium, press the "up"

or "down" arrow pads to scroll through the self-cleaning

settings.

CL-H (Clean - Heavy soil, 4 hours)

CL-M (Clean - Medium soil, 3 hours)

CL-L (Clean - Light soil, 2 hours)

Choosing a cleaning level automatically programs the self-

cleaning time.

After 4 seconds, "CLEAN," "DELAY," and "LOCK" will appear

in the display to show that the oven is set for a delayed clean

operation. The delay time is displayed.

To change the delay self-clean time:

1. Press DELAY.

"DELAY" flashes and "00:00" will appear in the display.

2. Press the "up" or "down" arrow pads to enter the amount of

time you want to delay the cycle.

After 4 seconds, "CLEAN," "DELAY," and "LOCK" will appear

in the display to show that the oven is set for a delayed clean

operation. The delay time is displayed.

When the self-clean cycle starts:

"DELAY" will turn off and the clean time will appear in the display.

To Stop Self-Clean Anytime:

Press CANCEL. All words disappear from the display. All

functions are canceled. The time of day appears in the display.

Depending on the actual oven temperature when self-clean is

canceled, the oven door may remain locked until the oven cools.

IMPORTANT: Before cleaning, make sure all controls are off and

the oven and cooktop are cool. Always follow label instructions

on cleaning products.

Soap, water and a soft cloth or sponge are suggested first unless

otherwise noted.

EXTERIOR PORCELAIN ENAMEL SURFACES

Food spills containing acids, such as vinegar and tomato, should

be cleaned as soon as the entire range is cool. These spills may

affect the finish.

Cleaning Method:

• Glass cleaner, mild liquid cleaner or nonabrasive scrubbing

pad:

Gently clean around the model and serial number plate

because scrubbing may remove numbers.

• All-Purpose Appliance Cleaner Part Number 31682 (not

included):

See "Assistance or Service" section to order.

STAINLESS STEEL (on some models)

Cleaning Method:

Rub in direction of grain to avoid damaging.

• Stainless Steel Cleaner and Polish Part Number 31462 (not

included):

• See "Assistance or Service" section to order.

• Liquid detergent or all-purpose cleaner:

Rinse with clean water and dry with soft, lint-free cloth.

To avoid damage to stainless steel, do not use soap-filled

scouring pads, abrasive cleaners, Cooktop Polishing Creme,

steel-wool pads, gritty washcloths or abrasive paper towels.

CERAMIC GLASS (on some models)

Cleaning Method:

Always wipe with a clean, wet cloth or sponge and dry thoroughly

to avoid streaking and staining.

Cooktop Cleaner Part Number 31464 is recommended regularly

to help avoid scratches, pitting and abrasions and to condition

the cooktop, and can be ordered as an accessory. See

"Assistance or Service" section to order.

Cooktop Scraper Part Number WA906B is also recommended for

stubborn soils, and can be ordered as an accessory. See

"Assistance or Service" section to order. The Cooktop Scraper

uses razor blades. Store razor blades out of the reach of children.

Light to moderate soil

• Paper towels or clean damp sponge

Sugary spills (jellies, candy, syrup)

• Cooktop Scraper:

Scrape off sugary spills while the cooktop is still warm. You

may want to wear oven mitts while cleaning the cooktop.

• Cooktop Polishing Creme and clean damp paper towel:

Clean as soon as cooktop has cooled down. Rub creme into

surface with a damp paper towel or soft cloth. Continue

rubbing until white film disappears.

Heavy soil, dark streaks, specks and discoloration

• Cooktop Polishing Creme or nonabrasive cleanser:

Rub product into soil with a damp paper towel or soft cloth.

Continue rubbing until white film disappears.

Burned-on soil

• Cooktop Cleaner and Cooktop Scraper:

Rub creme into soil with damp paper towel. Hold scraper as

flat as possible on surface and scrape. Repeat for stubborn

spots. Polish entire cooktop with creme and paper towel.

Metal marks from aluminum and copper

• Cooktop Cleaner:

Clean as soon as cooktop has cooled down. Rub creme into

surface with a damp paper towel or soft cloth. Continue

rubbing until white film disappears. The marks will not totally

disappear, but after many cleanings they will become less

noticeable.

Tiny scratches and abrasions

• Cooktop Cleaner:

Rub creme into surface with a damp paper towel or soft

cloth. Continue rubbing until white film disappears. Scratches

and abrasions do not affect cooking performance, and after

many cleanings they will become less noticeable.

To avoid damage to the cooktop, do not use steel wool, abrasive

powder cleansers, chlorine bleach, rust remover or ammonia.

COOKTOP CONTROLS

To avoid damage to the cooktop controls, do not use steel wool,

abrasive cleansers or oven cleaner.

To avoid damage, do not soak knobs.

When removing or replacing knobs, make sure knobs are in the

Off position.

Do not remove seals under knobs, if present.

Cleaning Method:

• Warm, soapy water or dishwasher:

Pull knobs straight away from control panel to remove.

CONTROL PANEL

To avoid damage to the control panel, do not use abrasive

cleaners, steel-wool pads, gritty washcloths or abrasive paper

towels.

To avoid turning the controls on while cleaning, you may activate

the Control Lock feature (on some models). See "Control Lock"

section.

Cleaning Method:

• Glass cleaner and soft cloth or sponge:

Apply glass cleaner to soft cloth or sponge, not directly on

panel.

• All-Purpose Appliance Cleaner Part Number 31682 (not

included):

See "Assistance or Service" section to order.

OVEN DOOR EXTERIOR

Cleaning Method:

• Glass cleaner and paper towels or nonabrasive plastic

scrubbing pad: Apply glass cleaner to soft cloth or sponge,

not directly on panel.

• All-Purpose Appliance Cleaner Part Number 31682 (not

included):

See "Assistance or Service" section to order.

OVEN CAVITY

Do not use oven cleaners.

Food spills should be cleaned when oven cools. At high

temperatures, foods react with porcelain and staining, etching,

pitting or faint white spots can result.

Cleaning Method:

• Self-Cleaning cycle: See "Self-Cleaning Cycle" first.

OVEN RACKS

Cleaning Method:

• Self-Cleaning cycle:

See "Self-Cleaning Cycle" first. Remove racks, or they will

discolor and become harder to slide. If this happens, a light

coating of vegetable oil applied to the rack guides will help

them slide.

• Steel-wool pad

STORAGE DRAWER (on some models)

Make sure drawer is cool and empty before cleaning.

For more information, see "Storage Drawer" section.

Cleaning Method:

• Mild detergent

Drawer Liner (on some models)

Remove all stored items from drawer and lift out drawer liner.

• Clean with mild detergent

• All-Purpose Appliance Cleaner Part Number 31682 (not

included):

• See "Assistance or Service" section to order.

The oven light is a standard 40-watt appliance bulb. Before

replacing, make sure the oven and cooktop are cool and the

control knobs are in the oft position.

To Replace:

1. Unplug range or disconnect power.

2. Turn the glass bulb cover in the back of the oven

counterclockwise to remove.

3. Turn bulb counterclockwise to remove from socket.

4. Replace bulb, then bulb cover by turning clockwise.

5. Plug in range or reconnect power.

The storage drawer can be removed. Before removing, make sure

drawer is cool and empty.

To Remove:

1. Pull storage drawer out to the first stop position.

2. Lift up the front of the drawer and pull the drawer out to the

second stop position.

3. Grasp sides and lift drawer top up and out.

To Replace:

1. Fit the ends of the drawer glides into the rails in the range.

2. Lift up the front of the drawer and gently push in to the first

stop position.

3. Lift drawer up again and push until drawer is closed.

For normal range use, it is not suggested to remove the oven

door. However, if removal is necessary, make sure the oven is off

and cool. Then, follow these instructions. The oven door is heavy.

To Remove:

1. Open oven door to the first stop position (opened about

4" (10.0 cm).

2. Grasp door at each side. Do not use the door handle to lift

door.

3. Lift up evenly until door clears hinge arms.

To Replace:

1. Grasp door at each side.

2. Align slots in the door with the hinge arms on the range.

3. Slide the door down onto the hinge arms until the door is

completely seated on the hinges. Push down on the top

corners of the door to completely seat door on hinges. Door

should not appear crooked.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.

Nothing will operate

• Has a household fuse blown, or has a circuit breaker

tripped? Replace the fuse or reset the circuit.

Cooktop will not operate

• Is the control knob set correctly? Push in knob before

turning to a setting.

Excessive heat around cookware on cooktop

Is the cookware the proper size? Use cookware about the

same size as the surface cooking area, element or surface

burner. Cookware should not extend more than V2"(1.3 cm)

outside the cooking area.

Hot Surface indicator light stays on (on some models)

• Does the Hot Surface indicator light stay on after control

knob(s) have been turn off? See "Cooktop Controls"

section.

Cooktop cooking results not what expected

Is the proper cookware being used? See "Cookware"

section.

• Is the control knob set to the proper heat level? See

"Cooktop Controls" section.

• Is the range level? Level the range. See the Installation

Instructions.

Oven will not operate

Is the electronic oven control set correctly? See

"Electronic Oven Control" section.

Has a delay start been set? See "Cook & Hold" section.

On some models, is the Control Lock set? See "Control

Lock" section.

Oven temperature too high or too low

Does the oven temperature calibration need adjustment?

See "Oven Temperature Control" section.

On some models, does the cooling fan run during Bake,

Broil or Clean?

It is normal for the fan to automatically run when the oven is

in use. This helps cool the electronic control.

Oven indicator lights flash

• Do the oven indicator lights flash? See the "Electronic

Oven Control" section. If the indicator light(s) keeps flashing,

call for service. See "Assistance or Service" section.

Display shows messages

• Is "BAKE" or "LOCK" flashing in the display? There has

been a power failure. Clear the display. See "Display" section.

Reset the clock, if needed. See "Clock" section. If it

reappears, call for service. See "Assistance or Service"

section.

Self-CleaningCyclewillnotoperate

• Is the oven door open? Close the oven door all the way.

• Has the function been entered? See "Self-Cleaning Cycle"

section.

• Has a delay start Self-Clean cycle been set? See "Self-

Cleaning Cycle" section.

• Has a delay start been set? See "Cook & Hold" section.

Oven cooking results not what expected

• Is the range level? Level the range. See the Installation

Instructions.

• Is the proper temperature set? Double-check the recipe in

a reliable cookbook.

• Is the proper oven temperature calibration set? See "Oven

Temperature Control" section.

Was the oven preheated? See "Bake" and "Broil" sections.

Is the proper bakeware being used? See "Bakeware"

section.

Are the racks positioned properly? See "Positioning Racks

and Bakeware" section.

Is there proper air circulation around bakeware? See

"Positioning Racks and Bakeware" section.

Is the batter evenly distributed in the pan? Check that

batter is level in the pan.

Is the proper length of time being used? Adjust cooking

time.

Has the oven door been opened while cooking? Oven

peeking releases oven heat and can result in longer cooking

times.

• Are baked items too brown on the bottom? Move rack to

higher position in the oven.

• Are pie crust edges browning early? Use aluminum foil to

cover the edge of the crust.

ASSISTANCEOR SERVICE

Before calling for assistance or service, please check

"Troubleshooting." It may save you the cost of a service call. If

you still need help, follow the instructions below.

When calling, please know the purchase date and the complete

model and serial number of your appliance. This information will

help us to better respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new IKEA® appliance.

To locate factory specified parts in your area, call us or your

nearest designated service center.

)n#se USA

Call the Whirlpool Customer eXperience Center

toll free: 1-800-253-1301.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Installation information.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

• Referrals to local dealers, repair parts distributors and service

companies. Whirlpool designated service technicians are

trained to fulfill the product warranty and provide after-

warranty service, anywhere in the United States.

To locate the Whirlpool designated service company in your

area, you can also look in your telephone directory Yellow

Pages.

For further assistance

If you need further assistance, you can write to Whirlpool

Corporation with any questions or concerns at:

IKEA Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

Call the Whirlpool Canada LP Customer eXperience Centre toll

free: 1-800-807-6777.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Referrals to local dealers, repair parts distributors, and

service companies. Whirlpool Canada LP designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to Whirlpool

Canada LP with any questions or concerns at:

Customer eXperience Centre

Whirlpool Canada LP

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

WHIRLPOOLCORPORATIONMAJOR APPLIANCEWARRANTY

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for Factory Specified Parts

and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.

This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in the country in

which it was purchased. Outside the 50 United States and Canada, this limited warranty does not apply. Proof of original purchase date

is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use or when it is used in a manner that is

contrary to published user or operator instructions and/or installation instructions.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved by Whirlpool.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.

6. Any food loss due to refrigerator or freezer product failures.

7. Costs associated with the removal from your home of your major appliance for repairs. This major appliance is designed to be

repaired in the home and only in-home service is covered by this warranty.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Whirlpool servicer is not available.

10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with published installation instructions.

11. Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty

is void if the factory applied serial number has been altered or removed from your major appliance.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.

If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," you may find

additional help by checking the "Assistance or Service" section or by calling Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada,

call 1-800-807-6777. 9/07

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

SECURITEDELA CUISINIERE

Votre securite et celle des autres est tres importante.

Nous donnons de nombreux messages de s_curit_ importants dans ce manuel et sur votre appareil m_nager. Assurez-vous de

toujours lire tousles messages de s_curit_ et de vous y conformer.

Voici le symbole d'alerte de s_curit&

Ce symbole d'alerte de s_curit_ vous signale les dangers potentiels de d_c_s et de blessures graves & vous

et &d'autres.

Tousles messages de s_curit_ suivront le symbole d'alerte de s_curit_ et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient •

Risque possible de d_cbs ou de blessure grave si vous ne

suivez pas imm_diatement les instructions.

Risque possible de d_cbs ou de blessure grave si vous

ne suivez pas les instructions.

Tousles messages de s_curit_ vous diront quel est le danger potentiel et vous disent comment r_duire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Dans les conditions de service normales, la cuisiniere ne bascule pas. Elle peut cependant basculer si une force ou un poids excessif

est appliqu6 sur la porte ouverte alors que la bride antibasculement n'est pas convenablement fixee.

Risque de basculement

Un enfant ou une personne adulte peut faire basculer la cuisiniere ce qui peut causer un d_ces.

Joindre la bride antibasculement au pied arriere de la cuisiniere.

Joindre de nouveau la bride antibasculement si la cuisiniere est d_plac_e.

Voir d_tails dans les instructions d'installation.

Le non-respect de ces instructions peut causer un d_ces ou des br_)lures graves aux enfants et

aux adultes.

La bride

""" antibasculement

Le ied de la cuisiniere

Assurez-vous qu'une bride antibasculement est install_e :

• Glisser la cuisiniere vers I'avant.

• V_rifier que la bride antibasculement est bien fix_e au plancher ou au mur.

• Glisser de nouveau la cuisiniere vers I'arriere de sorte que le pied est sous la bride

antibasculement.

IMPORTANTES INSTRUCTIONS DE SECURITE

AVERTISSEMENT : Pour r6duire le risque d'incendie, de

choc 61ectrique, de blessures ou de dommages Iors de

I'utilisation de la cuisini@e, il convient d'observer certaines

pr6cautions 616mentaires dont les suivantes :

• AVERTISSEMENT • POUR MINIMISER LE RISQUE

DE BASCULEMENT DE LA CUISINIERE, ELLE DOlT

€:TRE BIEN IMMOBILISC:E PAR DES DISPOSITIFS

ANTIBASCULEMENT CORRECTEMENT INSTALL¢:S.

POUR VC:RIFIER SI LES DISPOSITIFS SONT

CORRECTEMENT INSTALL¢:S, GLISSER LA CUISINIERE

VERS L'AVANT ET VC:RIFIER SI LA BRIDE

ANTIBASCULEMENT EST BIEN FlXC:E AU PLANCHER,

ET GLISSER LA CUISINIERE VERS L'ARRIERE POUR

QUE LE PIED ARRIERE DE LA CUISINIERE SOIT SOUS

LA BRIDE ANTIBASCULEMENT.

• MISE EN GARDE : Ne pas remiser dans des armoires

au-dessus de la cuisini@e ou sur le dosseret d'une

cuisini@e, des objets que des enfants pourraient vouloir

atteindre. Les enfants pourraient se brt_ler ou se blesser en

grimpant sur la cuisini@e.

• Installation appropri6e - S'assurer que la cuisini@e est

correctement install6e et reli6e & la terre par un technicien

qualifi6.

• Ne jamais utiliser la cuisiniere pour r6chauffer ou chauffer

la piece.

• Ne pas laisser les enfants seuls - Les enfants ne doivent

pas 6tre laiss6s seuls ou sans surveillance dans la piece

o(_la cuisini@e est en service. Ne jamais laisser les

enfants s'asseoir ou se tenir sur une partie quelconque de

la cuisini@e.

• Porter des v6tements appropri6s - Des v6tements amples

ou d6tach6s ne doivent jamais 6tre port6s pendant

I'utilisation de la cuisini_re.

• Entretien par I'utilisateur- Ne pas r6parer ni remplacer

toute piece de la cuisini@e si ce n'est pas sp6cifiquement

recommand6 dans le manuel. Toute autre op6ration

d'entretien ou de r6paration doit 6tre confi6e & un

technicien qualifi6.

• Remisage dans ou sur la cuisini_re - Des mat6riaux

inflammables ne doivent pas 6tre remis6s dans un four ou

pros des 616ments de surface.

• Ne pas utiliser d'eau pour 6teindre un feu de graisse -

¢:touffer le feu ou les flammes ou utiliser un extincteur

produits chimiques secs, ou un extincteur a mousse.

• N'utiliser que des mitaines s_ches de four - Des mitaines

de four mouill6es ou humides sur des surfaces chaudes

peuvent provoquer des br01ures provenant de la vapeur.

Ne pas laisser les mitaines de four toucher les 616ments

chauffants. Ne pas utiliser une serviette ou un tissu 6pais.

• NE PAS TOUCHER LES ¢:LEMENTS DE SURFACE OU

L'ESPACE PRF:S DES ¢:L¢:MENTS - Les 616ments de

surface peuvent 6tre chauds m6me Iorsqu'ils ont une teinte

fonc6e. Les endroits pros des 616ments de surface peuvent

devenir assez chauds pour causer des br01ures. Pendant

et apr_s I'utilisation, ne pas toucher les 616ments

chauffants et ne pas laisser les v6tements ou autres

mat6riaux inflammables entrer en contact avec ces

616ments de surface ou les endroits pros des 616ments,

avant qu'ils soient suffisamment refroidis. Ces endroits

comprennent la table de cuisson et les surfaces pros de la

table de la cuisson.

• Utiliser des ustensiles de dimension appropri6e - La

cuisini@e est munie d'un ou de plusieurs 616ments

chauffants de diff6rentes grandeurs. Choisir les ustensiles

qui ont un fond plat assez grand pour couvrir 1'616ment

chauffant de la surface de cuisson. L'utilisation d'ustensiles

trop petits exposera une partie de 1'616mentchauffant, ce

qui peut provoquer I'inflammation des v6tements.

L'utilisation d'un r6cipient de dimension correcte am61iore

aussi I'efficacit6 de la cuisson.

• Ne jamais laisser les 616ments de la table de cuisson sans

surveillance alors qu'ils chauffent a la puissance maximale.

II pourrait en r6sulter une 6bullition qui cause de la fum6e

et des renversements de corps gras qui peuvent

s'enflammer.

• S'assurer que les cuvettes r6fl6chissantes ou les bols de

renversement sont en place - L'absence de ces cuvettes

ou bols au cours de la cuisson peut causer des dommages

aux ills ou aux composants en dessous des 616ments.

• Garnissages protecteurs - Ne pas recouvrir les cuvettes

ou le fond du four de papier d'aluminium sauf tel que

sugg6r6 dans le manuel. L'installation incorrecte de papier

d'aluminium ou d'autre mat6riau peut causer un risque de

choc 61ectrique ou d'incendie.

• Ustensiles de cuisson vitrifi6s - Seulement certains types

d'ustensiles de verre, vitroc6ramique, c6ramique, fai'ence

ou autres surfaces vitrifi6es conviennent pour le service

sur une table de cuisson, sans bris attribuables aux

changements soudains de temp6rature.

• Les poign6es des ustensiles doivent 6tre tourn6es vers

I'int6rieur et non vers le dessus des 616ments adjacents -

Pour r6duire le risque de br01ures, d'inflammation de

produits inflammables et de renversements dus

I'entrechoquement non intentionnel des ustensiles, la

poign6e d'un ustensile doit 6tre positionn6e de sorte

qu'elle est tourn6e vers I'int6rieur et non au-dessus des

616ments de surface adjacents.

• Ne pas tremper les 616ments de chauffage amovibles -

Les 616ments de chauffage ne doivent jamais 6tre

immerg6s dans I'eau.

• Ne pas faire cuire sur une table de cuisson endommag6e -

Si la table de cuisson est bris6e, les solutions de nettoyage

et les renversements peuvent p6n6trer dans la table de

cuisson bris6e et cr6er un risque d'un choc 61ectrique.

Contacter imm6diatement un technicien qualifi6.

CONSERVEZ CES INSTRUCTIONS

IMPORTANTES INSTRUCTIONS DE SECURITE

• Nettoyer la table de cuisson avec prudence - Si une

_ponge ou un chiffon mouill_ est utilis_ pour essuyer les

renversements sur une surface de cuisson chaude, _viter

les brt]lures caus_es par la vapeur chaude. Certains

nettoyants peuvent produire des _manations d_sagr_ables

Iorsqu'ils sont utilis_s sur une surface chaude.

• Exercer une grande prudence Iors de I'ouverture de la

porte - Laisser I'air chaud ou la vapeur s'_chapper avant

d'enlever ou de replacer un plat.

• Ne pas faire chauffer des contenants ferm_s -

L'accumulation de pression peut causer une explosion du

contenant et des blessures.

• Ne jamais obstruer les ouvertures des _vents.

• Positionnement des grilles du four - Toujours placer les

grilles du four en position d_sir_e pendant que le four est

froid. Si la grille doit 6tre d_plac_e pendant que le four est

chaud, ne pas laisser les mitaines de four toucher I'_l_ment

chaud du four.

• NE PAS TOUCHER LES 12LI2MENTS CHAUFFANTS OU

LES SURFACES INTI2RIEURES DU FOUR - Les

_l_ments chauffants peuvent 6tre chauds m6me s'ils ont

une teinte fonc_e. Les surfaces int_rieures d'un four

deviennent assez chaudes pour causer des brt]lures.

Pendant et apr_s I'utilisation, ne pas toucher ou laisser des

v6tements ou autres mat6riaux inflammables venir en

contact avec les _l_ments chauds ou les surfaces

int_rieures chaudes du four avant qu'ils aient eu assez de

temps pour refroidir. D'autres surfaces de I'appareil

peuvent devenir assez chaudes pour causer des brt]lures.

Ces surfaces comprennent les ouvertures de I'_vent du

four et les surfaces pros de ces ouvertures, les portes du

four, et les hublots des portes du four.

Pour les cuisini_res avec programme d'autonettoyage -

• Ne pas nettoyer le joint de la porte - Le joint de la porte

est essentiel pour I'_tanch_it& Veiller & ne pas frotter,

endommager ou d_placer le joint.

• Ne pas utiliser des produits commerciaux de nettoyage du

four - On ne doit pas utiliser un produit commercial de

nettoyage de four ou un enduit de protection des surfaces

internes du four quel qu'en soit le type, sur les surfaces du

four ou les surfaces voisines.

• Nettoyer uniquement les pi_ces indiqu_es dans le manuel.

• Avant d'ex_cuter le programme d'autonettoyage du four -

Oter la I_chefrite et son plat et les autres ustensiles.

Pour les appareils avec hotte de ventilation -

• Nettoyer les hottes de ventilation fr_quemment - La

graisse ne doit pas s'accumuler sur la hotte ou le filtre.

• Lorsque vous flambez des aliments sous la hotte, mettre le

ventilateur en marche.

CONSERVEZ CES INSTRUCTIONS

La page est en cours de chargement...

IKEA ISE630VS11 Le manuel du propriétaire

Marque: IKEA

Modèle: ISE630VS11

Catégorie: Cuisinières

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: IKEA ISE630VS11 Owner's manual

IKEA ISE630VS11 Le manuel du propriétaire

IKEA ISE630VS11 Le manuel du propriétaire

dans d''autres langues

Autres documents