KitchenAid KFRU488VSS00 Guide d'installation

Marque: KitchenAid

Modèle: KFRU488VSS00

Catégorie: Barbecues

Taper: Guide d'installation

Ce manuel convient également à

®itchen kid ®

FREESTANDING OLUDOOR GRILLS

(;_IIIII(?

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230

or visit our website at www.kitchenaid.com

In Canada, for assistance, installation and service, call: 1-800-807-6777

or visit our website at www.KitchenAid.ca

GRILS D'EXTERIEUR AUTOPORTANTS

I[I,;_II_._.._.l(.lllSQ ll,;_llhlll(.ll ..........' ° .... ,,.,_._,............._..............=_,......

Au Canada, pourassistance,installationou servicecomposez le1-800-807-6777

ou visitez notre site Web &www.KitchenAid.ca

Table of Contents/Table des matieres ............................................................................. 4

iMPORTANT:

Save for local electrical inspector's use.

Jnstaler: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

iMPORTANT:

_, conserver pour consultation par I'inspecteur local des installations 61ectriques.

Instalateur : Remettre les instructions d'installation au propri6taire.

Propri6taire : Conserver les instructions d'installation pour r6f6rence ult6rieure.

Models/Modeles

W10175731A

KFRU271VSS, KFRU361VSS, KFRU365VSS, KFRU368VSS, KFRU488VSS,

KFRS271TSS, KFRS361TSS, KFRS365TSS, KFRU368TSS, KFRU488TSS

OUTDOOR GRILL SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

_b, DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your

gas supplier or your fire department.

_, WARNING

1. Do not store or use gasoline or other

flammable liquids or vapors in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of

this or any other appliance.

State of California Proposition 65 Warnings:

WARNING: This product contains a chemical known to the State of California to cause cancer.

WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.

In the State of Massachusetts, the following installation instructions apply:

[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type.

[] A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT: This grill is manufactured for outdoor use only. For grills that are to be used at elevations above 2000 ft (609.6 m) orifice

conversion is required. See "Gas Supply Requirements" section. It is the responsibility of the installer to comply with the minimum

installation clearances specified on the model/serial rating plate. The model/serial rating plate for freestanding models can be found on

the right-hand inside cabinet wall.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electrical shock,

injury to persons, or damage when using the outdoor cooking

gas appliance, follow basic precautions, including the

following:

[] Do not install portable or built-in outdoor cooking gas

appliances in or on a recreational vehicle, portable trailer,

boat or in any other moving installation.

[] Always maintain minimum clearances from combustible

construction, see "Location Requirements" section.

[] The outdoor cooking gas appliance shall not be located

under overhead unprotected combustible construction.

[] This outdoor cooking gas appliance shall be used only

outdoors and shall not be used in a building, garage, or any

other enclosed area.

[] Keep any electrical supply cord and fuel supply hose away

from any heated surfaces.

[] Keep outdoor cooking gas appliance area clear and free

from combustible materials, gasoline and other flammable

vapors and liquids.

[] Do not obstruct the flow of combustion and ventilation air.

Keep the ventilation openings of the cylinder enclosure free

and clear from debris.

[] Inspect the gas cylinder supply hose before each use of the

outdoor cooking gas appliance. If the hose shows

excessive abrasion or wear, or is cut, it MUST be replaced

before using the outdoor cooking gas appliance. Contact

your dealer and use only replacement hoses specified for

use with the outdoor cooking gas appliance.

[] Visually check the burner flames. They should be blue.

Slight yellow tipping is normal for LP gas.

[] Check and clean burner/venturi tube for insects and insect

nest. A clogged tube can lead to fire under the outdoor

cooking gas appliance.

SAVE THESE

[] The LP gas supply cylinder to be used must be:

- constructed and marked in accordance with the

Specification for LP Gas Cylinders of the U.S. Department

of Transportation (DOT) or the National Standard of

Canada, CAN/CSA-B339, Cylinders, Spheres, and Tubes

for Transportation of Dangerous Goods; and Commission.

- provided with a listed overfilling prevention device.

- provided with a cylinder connection device compatible

with the connection for outdoor cooking gas appliances.

[] Always check connections for leaks each time you connect

and disconnect the LP gas supply cylinder. See

"Installation Instructions" section.

[] When the outdoor cooking gas appliance is not in use, the

gas must be turned off at the supply cylinder.

[] Storage of an outdoor cooking gas appliance indoors is

permissible only if the cylinder is disconnected and

removed from the outdoor cooking gas appliance.

[] Cylinders must be stored outdoors and out of the reach of

children and must not be stored in a building, garage, or

any other enclosed area.

[] The pressure regulator and hose assembly supplied with

the outdoor cooking gas appliance must be used. A

replacement pressure regulator and hose assembly

specific to your model is available from your outdoor

cooking gas appliance dealer.

[] Gas cylinder must include a collar to protect the cylinder

valve.

[] For appliances designed to use a CGA791 Connection:

Place a dust cap on cylinder valve outlet whenever the

cylinder is not in use. Only install the type of dust cap on

the cylinder valve outlet that is provided with the cylinder

valve. Other types of caps or plugs may result in leakage

of propane.

If the following information is not followed exactly, a fire

causing death or serious injury may occur.

[] Do not store a spare LP gas cylinder under or near this

outdoor cooking gas appliance.

[] Never fill the cylinder beyond 80 percent full.

iNSTRUCTiONS

TABLEOF CONTENTS

OUTDOOR GRILL SAFETY ............................................................ 2

INSTALLATION REQUIREMENTS ................................................ 5

Tools and Parts ............................................................................ 5

Location Requirements ................................................................ 5

Product Dimensions .................................................................... 6

Electrical Requirements ............................................................... 6

Gas Supply Requirements ........................................................... 7

Gas Connection Requirements .................................................... 7

INSTALLATION INSTRUCTIONS .................................................. 9

Freestanding Outdoor Grill Installation ........................................ 9

GAS CONVERSIONS .................................................................... 14

Tools and Parts for Gas Conversion .......................................... 14

Conversion to a Local LP Gas Supply ....................................... 15

Conversion from LP Gas to Natural Gas ................................... 16

Check and Adjust the Burners ................................................... 19

OUTDOOR GRILL USE ................................................................ 20

ELECTRONIC GRILL DISPLAY ................................................... 20

Display ........................................................................................ 20

Start/Reset ................................................................................. 20

Mode .......................................................................................... 20

Using Your Outdoor Grill ............................................................ 22

Using Your Infrared Sear Burner ................................................ 23

Using Your Side Burner ............................................................. 23

Using Your Rotisserie ................................................................. 24

Rotisserie Cooking Tips ............................................................. 26

Using Your Smoker Box ............................................................ 27

Hood Lights ................................................................................ 27

USING YOUR WARMING DRAWER ........................................... 27

Control Knob .............................................................................. 27

Moist-Dry Slide Control .............................................................. 28

Setting the Controls ................................................................... 28

Warming Cookware ................................................................... 29

Warming Pans and Positioning Rack ........................................ 29

Proofing Bread ........................................................................... 29

Slow Cook Function ................................................................... 29

TIPS FOR OUTDOOR GRILLING ................................................ 30

Cooking Methods ....................................................................... 30

Grilling Chart............................................................................... 31

OUTDOOR GRILL CARE ............................................................. 33

Replacing the Batteries .............................................................. 33

General Cleaning ........................................................................ 34

Drawer Slides ............................................................................. 36

Drawer Removal ......................................................................... 36

Cabinet Door Alignment - Style 2 (internal hinge) Only ............. 37

Cabinet Door Removal ............................................................... 37

TROUBLESHOOTING .................................................................. 38

ASSISTANCE OR SERVICE ......................................................... 39

In the U.S.A................................................................................ 39

Accessories ................................................................................ 39

In Canada ................................................................................... 39

WAR RANTY .................................................................................. 40

TABLE DES MATIERES

SI_CURITI_ DU GRIL D'EXTI_RIEUR ........................................... 41

EXIGENCES D'INSTALLATION ................................................... 43

Outillage et pieces ...................................................................... 43

Exigences d'emplacement ......................................................... 43

Dimensions du produit .............................................................. 44

Specifications electriques .......................................................... 44

Specifications de I'alimentation en gaz ..................................... 45

Exigences concernant le raccordement au gaz ........................ 46

INSTRUCTIONS D'INSTALLATION ............................................. 47

Installation du gril d'exterieur autoportant ................................. 47

CONVERSIONS DE GAZ .............................................................. 52

Outillage et pieces pour la conversion ....................................... 52

Conversion au gaz propane local .............................................. 53

Conversion de gaz propane & gaz naturel ................................. 54

Contr61e et reglage des brQleurs................................................ 57

UTILISATION DU GRIL D'EXTI_RIEUR ....................................... 58

AFFICHEUR I_LECTRONIQUE DU GRIL .................................... 59

Afficheur ..................................................................................... 59

Start/Reset (demarrage/r6initialisation) ...................................... 59

Mode ........................................................................................... 59

Utilisation du gril d'exterieur ....................................................... 60

Utilisation du brQleur & infrarouge .............................................. 62

Utilisation du brQleur lateral........................................................ 62

Utilisation du tournebroche ........................................................ 63

Conseils de cuisson & I'aide du tournebroche .......................... 64

Utilisation du fumoir ................................................................... 65

Lampes du capot ....................................................................... 65

UTILISATION DU TIROIR-RI_CHAUD ......................................... 66

Bouton de commande ............................................................... 66

Curseur de reglage Moist-Dry (humide-sec) .............................. 66

Reglage des commandes .......................................................... 66

Ustensiles de rechauffage .......................................................... 67

Ustensiles de rechauffage et grille de positionnement .............. 67

Levee du pain ............................................................................. 68

Fonction de cuisson lente .......................................................... 68

CONSEILS POUR L'UTILISATION DU GRIL

D'EXTI_RIEUR .............................................................................. 68

Methodes de cuisson ................................................................. 69

Tableau de cuisson au gril ......................................................... 70

ENTRETIEN DU GRIL D'EXTI_RIEUR ......................................... 72

Changement de I'ampoule d'eclairage ...................................... 72

Remplacement des piles ............................................................ 72

Nettoyage gen6ral ...................................................................... 73

Glissieres de tiroir ....................................................................... 75

Depose du tiroir .......................................................................... 75

Alignement de la porte du placard -

Style 2 (charniere interne) uniquement ...................................... 76

Depose de la porte du placard .................................................. 76

DI_PANNAGE ................................................................................. 77

ASSISTANCE OU SERVICE ......................................................... 78

Au Canada .................................................................................. 78

Accessoires ................................................................................ 78

GARANTIE ..................................................................................... 79

INSTALLATION REQUIREMENTS

asd Pa s

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

• Tape measure •

• Small, flat-blade screwdriver •

• Flat-blade screwdriver •

• #2 and #3 Phillips screwdriver

• Level •

• Short Phillips screwdriver or a

90 ° screwdriver with a Phillips

screw bit

Wrench or pliers

Pipe wrench

Scissors or cutting pliers

(to remove tiedowns)

Noncorrosive leak-

detection solution

Parts Supplied

• Gas pressure regulator/hose assembly set for 11" WCP LP

gas (attached to manifold)

• Natural gas conversion kit with convertible regulator set for 4"

WCP Natural gas (on some models)

• Natural gas conversion kit (on some models)

• Rotisserie motor mounting bracket (on some models)

• Rotisserie motor (on some models)

• Rotisserie forks (on some models)

• Rotisserie spit (on some models)

• Smoker box (on some models)

• 2 warming drawer pans (on some models)

• 1 single-prong plug/500 mAmp transformer assembly for the

rotisserie motor (on some models)

• 2 - 1.5 V "D" size alkaline batteries (on some models)

• Vinyl grill cover (on some models)

Parts Needed

• 20 Ib LP gas fuel tank - approximately 18" (45.7 cm) height

and 12" (30.5 cm) diameter

• UL outdoor-rated 120 V extension cord - size 14 gauge/3 wire

(marked 14/3 W-A), 50 foot (15.2 m) maximum length

Explosion Hazard

Do not store fuel tank in a garage or indoors.

Do not store grill with fuel tank in a garage or indoors.

Failure to follow these instructions can result in death,

explosion, or fire.

Fire Hazard

Do not use grill near combustible materials.

Do not store combustible materials near grill.

Doing so can result in death or fire.

Select a location that provides minimum exposure to wind and

traffic paths. The location should be away from strong draft

areas.

Do not obstruct flow of combustion and ventilation air.

Clearance to combustible construction for freestanding outdoor

grills:

• A minimum of 24" (58 cm) must be maintained between the

front of the grill hood, sides and back of the grill and any

combustible construction.

• A 24" (58 cm) minimum clearance must also be maintained

below the cooking surface and any combustible construction.

Rotisserie

A 6" (15.2 cm) minimum clearance is needed for the rotisserie

motor.

A grounded, 3-prong outdoor outlet is located on the back of the

grill. See "Electrical Requirements" section.

NOTE: The rotisserie is an accessory on some models. See the

"Assistance or Service" section to order.

17W'

cm)

..... :T;,

,,"_T..................... _,,

f i

L t

17W'

(43.8 cm)

62%"

(158.7 crn)

50W'

(127.2 cm)

@ @_@@@@

28Vd'

(72.4 crn)

front of

handle to

back of grimm

A. 61 V2"(156.2 cm) on 27" (68.6 cm) models KFRS2 71T and KFRU2 71V

70Y2"(179.1 cm) on 36" (91.4 em) models KFRS361 T,KFRU361 V,

KFRS365T and KFRU365V

84Y2" (214.6 em) on 36" (91.4 em) models with side burner -

KFRU368T and KFRU368V

96Y2" (245.1 em) on 48" (121.9 em) models with side burner -

KFRU488T and KFRU488V

B. 27" (68.6 em)

36" (91.4 cm)

48" (121.9 cm)

C. Not available on 27" (68.6 cm) models

14" (35.6 cm) on 36" (91.4 cm) and 48" (121.9 cm) models

To avoid electrical shock, do not immerse cord or plugs in

water or other liquid.

Unplug from the outlet when not in use and before cleaning.

Allow to cool before putting on or taking off parts.

Do not operate any outdoor cooking gas appliance with a

damaged cord, damaged plug, or after the appliance

malfunctions or has been damaged in any manner. Contact

the manufacturer for repair.

Do not let the cord hang over the edge of a table or touch hot

surfaces.

• Do not use an outdoor cooking appliance for purposes other

than intended.

When connecting, first connect plug to the outdoor cooking

gas appliance then plug appliance into the outlet.

Use only a Ground Fault Interrupter (GFI) protected circuit

with this outdoor cooking gas appliance.

Do not remove the ground prong or use with an adapter of

2 prongs.

Use only extension cords with a 3 prong grounding plug rated

for the power of the equipment and approved for outdoor use

with a W-A marking.

The model/serial number rating plate is located inside the grill

cabinet on the right-hand cabinet side. See the following

illustration.

x.@:?I_,. :*@?__.@ ?_I't:,,,

Electrical Shock Hazard

Use only a UL listed, 14 gauge, 3 wire extension cord

approved for outdoor use, marked W=A, with a

maximum length of 50 ft.

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Failure to follow these instructions can result in death,

fire, or electrical shock.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

Check with a qualified electrician if you are not sure whether the

grill is properly grounded.

A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical supply is

required.

It is recommended that a separate circuit servicing only this grill

be provided.

A. Model/serial number plate

Recommended Ground Method

The outdoor grill, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes,

with the National Electrical Code ANSI/NFPA 70, or Canadian

Electrical Code, CSA C22.1.

Copies of the standards listed above may be obtained from:

CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

S ............................

A.3-prong ground plug

B.3-prong polarized type outdoor GFI outlet

C. Ground prong

Explosion Hazard

Use a new CSA International approved "outdoor"

gas supply line.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1 - latest edition or CAN/CGA B149.1 - latest

edition.

IMPORTANT: Grill must be connected to a regulated gas supply.

Refer to the model/serial rating plate for information on the type

of gas that can be used. If this information does not agree with

the type of gas available, check with your local gas supplier.

Gas Conversion:

No attempt shall be made to convert the grill from the gas

specified on the model/serial rating plate for use with a different

gas type without consulting the serving gas supplier. The

conversion kit supplied with grill must be used. See "Gas

Conversions" section for instructions.

Gas Pressure Regulator

The gas pressure regulator supplied with this grill must be used.

The inlet (supply) pressure to the regulator should be as follows

for proper operation:

LP Gas:

Operating pressure: 11" (27.9 cm) WCP

Inlet (supply) pressure: 11" to 14" (27.9 cm to 35.5 cm) WCP

Natural Gas:

Operating pressure: 4" (10.2 cm) WCP

Inlet (supply) pressure: 7" to 14" (17.8 cm to 35.5 cm) WCP

maximum.

Contact local gas supplier if you are not sure about the inlet

(supply) pressure.

Burner Requirements for High Altitude

Input ratings shown on the model/serial rating plate are for

elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a

rate of 4% for each 1,000 ft (304.8 m) above sea level. Orifice

conversion is required. See "Assistance or Service" section to

order.

Gas Supply Line Pressure Testing

Testing above 1/2psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge):

The grill and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing of

that system at test pressures greater than 1/2psi (3.5 kPa).

Testing below 1/2psi (3.5 kPa) or 14" (35.5 cm) WOP (gauge) or

lower:

The grill must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any pressure

testing of the gas supply piping system at test pressures equal to

or less than 1/2psi (3.5 kPa).

20 Ib LP Gas Fuel Tank

This grill is equipped for use with a 20 Ib LP gas fuel tank (fuel

tank not supplied). A gas pressure regulator/hose assembly is

supplied.

It is also design-certified by CSA International for local LP gas

supply or for Natural gas with appropriate conversion.

A. Gaspressure regulator/hose assembly

The 20 Ib LP gas fuel tank must be mounted and secured.

Drawer Style Tank Tray

1. Open the drawer for the 201b LP gas fuel tank.

2. Place the 20 Ib LP gas fuel tank bottom collar into the

mounting hole in the tank tray.

3. Tighten the locking screw against the bottom collar of the

20 Ib LP gas fuel tank to secure.

A , _

B C

A. Locking screw

B.Mounting hole

C. Bottom coflar

4. Slide the drawer with the 201b LP gas fuel tank back into the

cabinet.

DoorStyleTankTray

1. Opencabinetdoors.

2. Pressthelockingtabonthetanktrayandpulloutthetray.

A. 20 Ib LP gas fuel tank tray locking tab

3. Place the 20 Ib LP gas fuel tank bottom collar into the

mounting hole in the tank tray.

4. Tighten the locking screw against the bottom collar of the

20 Ib LP gas fuel tank to secure.

B C

A. Locking screw

B. Mounting hole

C. Bottom collar

5. Slide the tank tray back into the cabinet and lock into place.

Local LP Gas Supply Conversion

Conversion must be made by a qualified gas technician. The

qualified gas technician shall provide the gas supply to the

selected grill location in accordance with the National Fuel Gas

Code ANSI Z223.1/NFPA 54 - latest edition, and local codes. For

conversion to local LP,the convertible regulator in the conversion

kit supplied with the grill (on some models) must be used. Models

that do not come with the conversion kit require Convertible

Regulator Part Number W10132702. See "Assistance or Service"

section for information on ordering.

IMPORTANT: The gas installation must conform with local

codes, or in the absence of local codes, with the National Fuel

Gas Code, ANSI Z223.1/NFPA 54 - latest edition. The qualified

LP gas technician shall provide the LP gas supply to the selected

grill location in accordance with the National Fuel Gas Code,

ANSI Z223.1/NFPA 54 and local codes.

Follow instructions for converting to local LP gas in the "Gas

Conversions" section.

<, _> < ,

S .............................................................

A. New ANSI Z21.54 certified gray hose

B. Rear of grill

C. To local LP gas supply

The gas supply line shall be equipped with an approved shutoff

valve. This valve should be located in the same area as the grill

and should be in a location that allows ease of opening and

closing. Do not block access to the shutoff valve. The valve is for

turning on or shutting off gas to the grill.

A. Gas supply line

B. Shutoff valve "open" position

C. To grill

Natural Gas Conversion

Conversion must be made by a qualified gas technician. The

qualified Natural gas technician shall provide the Natural gas

supply to the selected grill location in accordance with the

National Fuel Gas Code ANSI Z223.1/NFPA 54 - latest edition,

and local codes. For conversion to Natural gas, the Natural Gas

Conversion Kit supplied with the grill (on some models) or the

Natural Gas Conversion Kit Part Number W10118098 must be

used. See "Assistance or Service" section for information on

ordering.

IMPORTANT: The gas installation must conform with local

codes, or in the absence of local codes, with the National Fuel

Gas Code, ANSI Z223.1/NFPA 54 - latest edition.

Follow instructions for converting to Natural gas in the "Gas

Conversions" section of this manual or the instructions supplied

with Natural Gas Conversion Kit Part Number W10118098.

INSTALLATION

INSTRUCTIONS

():/ (}4}_

Excessive Weight Hazard

Use two or more people to move and install grill.

Failure to do so can result in back or other injury.

1. Unpack grill. Remove all packaging materials and remove grill

from wooden skid.

2. Move grill into desired outdoor location.

3. Open the hood.

Remove Packaging Material Inside the Grill

1. Cut the tiedowns holding the grates together.

2. Remove condiment shelf, warming shelf and grill grates from

inside the grill and remove packaging material.

3. Remove foam block and wrap from inside the grill.

A. New ANSI Z21.54 certified gray hose

B.Rear of grill

C. To Natural gas supply

The gas supply line shall be equipped with an approved shutoff

valve. This valve should be located in the same area as the grill

and should be in a location that allows ease of opening and

closing. Do not block access to the shutoff valve. The valve is for

turning on or shutting off gas to the grill.

A. Gas supply line

B. Shutoff valve "open" position

C. To grill

A ..........

,/ •

.......... _ //i;::_B

A. Foam block

B.Foam wrap

Replace the grill grates.

Place warming shelf on brackets as shown.

A A

A. Warming shelf brackets

B. Warming shelf

Attach Side Shelf (on some models)

1. Open doors below grill and remove carton. Unpack side

shelf.

2. Locate 4 screws. Install 2 screws in the top 2 holes on each

side of the grill. Leave screws away from side of grill about

1_,,(0.64 cm).

Install side shelf on left side of the grill. Position the side shelf

so that the large end of the keyhole slots are over the screws.

Place shelf onto the 2 mounting screws. Let the shelf slide

down so the screws are in the narrow neck of the slots.

A .....................

A. Top of side shelf

B. Keyhole slot

C. Front of side shelf

D. Side of grifl

4. Install the bottom 2 screws and tighten.

5. Tighten the top 2 screws.

Attach Cabinet Doors (on some models)

1. Remove foam wrapping from both cabinet doors.

2. Position hinge pins on the door with the hinge brackets on

the cabinet. Gently push down to slide the pins into place.

A. Door hinge pin

B. Hinge bracket

Attach Condiment Shelf (on some models)

1. Open cabinet door.

2. Use a short Phillips screwdriver or a 90 °screwdriver with a

Phillips screw bit to loosen the 2 mounting screws on the

inner door panel.

A. Mounting screws

Position the condiment shelf so that the large ends of the

keyhole slots are over the 2 mounting screws.

A.Mounting screw in keyholeslot

B.Condiment shelf

Lower the condiment shelf until the 2 mounting screws are in

the narrow ends of the keyhole slots.

Tighten the screws.

Dispose of/recycle all packaging material.

Make Gas Connection - To a 20 Ib LP Gas Fuel Tank

Explosion Hazard

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

If converting to local LP or Natural gas, follow instructions in the

"Gas Conversions" section.

LP Gas:

IMPORTANT: A 20 Ib LP gas fuel tank must be purchased

separately.

IMPORTANT: The gas pressure regulator/hose assembly

supplied with the grill must be used. Replacement gas pressure

regulator/hose assembly specific to your model, is available from

your outdoor grill dealer.

Drawer Style Tank Tray

To Install the 20 Ib LP Gas Fuel Tank:

1. Open the drawer for the 201b LP gas fuel tank.

2. Place the 20 Ib LP gas fuel tank bottom collar into the

mounting hole in the tank tray

3. Tighten the locking screw against the bottom collar of the

20 Ib LP gas fuel tank to secure.

B C

Screw the gas pressure regulator/hose assembly to the 20 Ib

LP gas fuel tank as shown. (To disconnect, turn off the gas

supply to the 20 Ib LP gas fuel tank, then unscrew the gas

pressure regulator/hose assembly from the 20 Ib LP gas fuel

tank as shown.)

A. 20 Ib LP gas fuel tank

B. Gaspressure regulator/hose assembly

5. Turn on the gas supply. Wait a few minutes for gas to move

through the gas line.

6. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

7. Slide the drawer with the 201b LP gas fuel tank back into the

cabinet.

8. The batteries are not factory installed. The 1.5-volt "D" size

alkaline batteries are located in the accessory box on the grill

grate. Install the batteries at this time following the

instructions in the "Replacing the Batteries" section.

9. Go to "Plug in Grill" in this section.

Door Style Tank Tray

To Install the 20 Ib LP Gas Fuel Tank:

1. Open cabinet doors.

2. Press the locking tab on the tank tray and pull out the tray..

A. Locking screw

B. Mounting hole

C. Bottom collar

A. 20 Ib LP gas fuel tank tray locking tab

3. Place the 20 Ib LP gas fuel tank bottom collar into the

mounting hole in the tank tray.

4. Tighten the locking screw against the bottom collar of the

20 Ib LP gas fuel tank to secure.

B C

A. Locking screw

B. Mounting hole

C. Bottom collar

Screw the gas pressure regulator/hose assembly to the 20 Ib

LP gas fuel tank as shown. (Todisconnect, turn off the gas

supply to the 20 Ib LP gas fuel tank, then unscrew the gas

pressure regulator/hose assembly from the 20 Ib LP gas fuel

tank as shown.

A. 20 Ib LP gas fuel tank

B.Gaspressure regulator/hose assembly

6. Turn on the gas supply. Wait a few minutes for gas to move

through the gas line.

7. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

8. Slide the tank tray back into the cabinet and lock into place.

9. The batteries are not factory installed. The 1.5-volt "D" size

alkaline batteries are located in the accessory box on the grill

grate. Install the batteries at this time following the

instructions in the "Replacing the Batteries" section.

10. Go to "Plug in Grill" in this section.

Gas Connection to Natural Gas or Local LP Gas

Explosion Hazard

Use a new CSA International approved "outdoor"

gas supply line.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water

column.

Examples of a quaJified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

This installation must conform with local codes and ordinances.

In the absence of local codes, installations must conform with

either the National Fuel Gas Code ANSI Z223.1, or CAN/CGA-

B149.1 Natural Gas and Propane installation code.

Copies of the standards listed above may be obtained from:

CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

1. Make gas connections.

A combination of pipe fittings must be used to connect the

grill to the existing gas line.

• If local codes permit, use an outdoor flexible stainless

steel tubing gas connector, design-certified by CSA

International, to connect the grill to the rigid gas supply

line. A 5/8"diameter line is recommended. Using a wrench

to tighten, connect the gas supply to the grill. Use pipe-

joint compound on all non-flared male threads. Do not

kink or damage the flexible connector when moving the

grill.

• Pipe-joint compounds suitable for use with LP gas must

be used. Do not use TEFLON ®ttape. Plug in Grill

C ........ !! .......................

A. New ANSI Z21.54 certified gray hose

B. Rear of grill

C. To Natural gas supply

Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

A. Closed valve

B. Open valve

3. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

4. The batteries are not factory installed. The 1.5-volt "D" size

alkaline batteries are located in the accessory box on the grill

grate. Install the batteries at this time following the

instructions in the "Replacing the Batteries" section.

5. Go to "Plug in Grill" in this section.

Electrical Shock Hazard

Use only a UL listed, 14 gauge, 3 wire extension cord

approved for outdoor use, marked W=A, with a

maximum length of 50 ft.

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Plug a UL outdoor rated 14 gauge/3 wire extension cord

(marked W-A) (maximum length 50 foot [15.2 m]) into the

male receptacle on the back of the grill.

A. UL outdoor rated 14 gauge/3 wire extension cord

B.Male receptacle

C. Circuit breaker button

2. Plug extension cord into grounded 3-prong GFI outlet.

S ...............................

A .... ".....................

A. 3-prong ground plug

B. 3-prong polarized type outdoor GFI outlet

C. Ground prong

To avoid electrical shock, do not immerse cord or plugs in

water or other liquid.

Unplug from the outlet when not in use and before

cleaning. Allow to cool before putting on or taking off

parts.

Do not operate any outdoor cooking gas appliance with a

damaged cord, damaged plug, or after the appliance

malfunctions or has been damaged in any manner.

Contact the manufacturer for repair.

t®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

Do not let the cord hang over the edge of a table or touch

hot surfaces.

Do not use an outdoor cooking appliance for purposes

other than intended.

When connecting, first connect plug to the outdoor

cooking gas appliance then plug appliance into the outlet.

Use only a Ground Fault Interrupter (GFI) protected circuit

with this outdoor cooking gas appliance.

Do not remove the ground prong or use with an adapter

of 2 prongs.

Use only extension cords with a 3 prong grounding plug

rated for the power of the equipment and approved for

outdoor use with a W-A marking.

NOTE: Check the circuit breaker on the back of the grill after

plugging the grill into a 3-prong polarized type outdoor GFI

outlet if there is a loss of electrical power to the grill. Reset

the circuit breaker if the button is in the tripped position. Push

in the rubber boot and button to reset.

A. Rubber boot

B. Circuit breaker button in

"set" position

A. Rubber boot

B. Circuit breaker button

in "tripped" position

3. Go to "Check and Adjust the Burners" section

GAS CONVERSIONS

NOTE: These instructions are for grill models that come equipped with the conversion kit for Local LP and Natural gas. For models that

do not come equipped with the conversion kit: for conversion to Local LP order Regulator Part Number W10132702, or for conversion

to Natural gas order LP to Natural Gas Conversion Kit Part Number W10118098. Use the conversion instructions included in the kit.

See "Assistance or Service" section for information on ordering.

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Phillips screwdriver

• Pipe wrench

• Adjustable wrench

• 10 mm wrench

• 6 mm socket and wrench

or 6 mm nut driver

• 10 mm socket and wrench

or 10 mm nut driver

• Thin flat-blade screwdriver

• Pliers

• Pipe thread sealant

certified for LP gas

Parts supplied

• Brass connector

• Convertible regulator 4" W.C. Natural, 11" W.C. LP

• Natural gas orifices

IMPORTANT: Gas conversions must be done by a qualified

installer. Before proceeding with conversion, shut off the gas

supply to the appliance prior to disconnecting the electrical

power.

This kit is designed for use from sea level up to 2000 ft elevation.

For higher elevations contact KitchenAid at 1-800-422-1230 in

the U.S.A. or call 1-800-607-6777 in Canada.

Explosion Hazard

Use a new CSA international approved "outdoor"

gas supply line.

Securely tighten all gas connections.

ifconnected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

I01 .,)CI I,I _ "'<,"__ _"_ .....

Installation of the regulator

1. Turn off the main gas supply valve.

2. Unplug grill or disconnect power.

3. Disconnect 20 Ib LP gas fuel tank (if present).

4. Turn off all burner control valves.

5. Remove rear cover and 2 screws.

Use adjustable wrench to remove LP hose regulator from

brass elbow. Use adjustable wrench to remove brass elbow

from shutoff valve.

9. Use pipe wrench to install the convertible regulator. Brass

cap will be facing up when tight.

A B

iii _,iiiiiio

A, Brass connector

B. Convertible regulator

10. To set the appliance regulator for LP gas, use adjustable

wrench to remove the brass cap on the convertible regulator.

A. Manifold

B.Brass elbow

C. Rear of grill

D. Gas pressure regulator/hose assembly

Apply pipe sealant to the threads of the brass connector. Use

pipe thread sealant that is certified for use with LP gas.

Use adjustable wrench to install brass connector (supplied) to

shutoff valve.

NOTE: The arrow on the regulator must be pointing toward

the brass connector.

11. Examine the stem on the brass cap. The letters "NAT" should

be showing on the end of the plastic stem farthest away from

the brass cap.

12. Remove stem from cap, turn it over and snap stem back into

the cap so the letters "LP" are at the end of the stem farthest

away from the brass cap.

13. Use adjustable wrench to reinstall cap onto regulator.

Make Grill Connections

Connect Local LP Gas Supply

1. Use pipe wrench to connect certified 1/2"(1.3 cm) gas supply

pipe to inlet side of regulator from Fixed LP gas supply

according to local codes requirements. Use pipe thread

sealant that is certified for use with LP gas at connections

where required. There must be a certified manual shutoff

valve in the gas supply line near the grill for easy access.

2. Turn on the gas supply to the grill.

3. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leaks found.

Record Conversion

In the last page of the Use and Care Guide, write "Converted to

Local LP Gas Supply." Also record the conversion date and the

technician/company that performed the conversion.

Installation of the regulator

1. Turn off the main gas supply valve.

2. Unplug grill or disconnect power.

3. Disconnect 20 Ib LP gas fuel tank (if present).

4. Turn off all burner control valves.

5. Remove rear cover and 2 screws.

Use adjustable wrench to remove LP hose regulator from

brass elbow. Use adjustable wrench to remove brass elbow

from shutoff valve.

9. Use pipe wrench to install the convertible regulator. Brass

cap will be facing up when tight.

A B

iii _'iiiiiio

A. Brass elbow

B. Convertible regulator

10. To make sure the regulator is set for Natural gas, use

adjustable wrench to remove brass cap on appliance

regulator.

A. Manifold

B.Brass elbow

C. Rear of grill

D. Gas pressure regulator/hose assembly

Apply pipe sealant to the threads of the brass connector. Use

pipe thread sealant that is certified for use with LP gas.

Use adjustable wrench to install brass connector (supplied) to

shutoff valve.

NOTE: The arrow on the regulator must be pointing toward

the brass connector.

11. Examine the stem on the brass cap. If the letters "NAT" are

not showing on the end of the plastic stem farthest away from

the brass cap, remove stem from cap, turn it over and snap

stem back into the cap so the letters "NAT" are at the end of

the stem farthest away from the brass cap.

12. Reinstall cap onto convertible regulator.

Change the main grill burner valve orifices

1. Manually remove all of the grates, sear plate, and burners.

2. Remove the 2 screws that hold the burner in place. Remove

gas burner from the grill.

A. Two screws

3= Use 6 mm socket and wrench or 6 mm nut driver to remove

the brass orifices from the end of the gas valves.

Change the Rotisserie-infrared burner orifice(s)

1. Remove the access cover and screw at the back of the grill

hood with a Phillips screwdriver.

A. Grill burner orifice

Install new 2.34 mm orifices supplied with this kit to the end

of the gas valve. Use 6 mm socket and wrench or 6 mm nut

driver to tighten.

NOTE: The number 2.34 is stamped on the orifice for

identification.

Use Phillips screwdriver to remove 2 screws holding the

spider guard to the burner.

B,(

A. Grill burnerorifice

Replace burner by sliding the middle tube (venturi) over the

orifice.

A.Burner/orifice connection

B.Burner

Reattach gas burner using 2 screws.

A. Two screws

Repeat the procedure for each grill burner.

A. Spider guard

B. Two screws

Use 10 mm wrench to remove the brass orifice located at the

end of the supply pipe.

For models with 1 rotisserie burner:

Install 1.9 mm orifice supplied with this kit to the end of the

supply pipe. Use 10 mm wrench to tighten.

For models with 2 rotisserie burners:

Install 1.55 mm orifice supplied with the kit to the end of the

supply pipe. Use 10 mm wrench to tighten.

NOTE: The number 1.9 mm or 1.55 mm is stamped on the

orifice for identification.

5. Replace the spider guard and secure with the 2 screws

removed in Step 2.

6. Repeat the procedure for each rear burner.

Change the Side burner orifices

(for models equipped with side burner)

1. Remove the side burner grates.

2. Remove the burner caps. The caps are interlocked to the

burner base. Twist and lift the burner caps to remove.

3. Use 10 mm socket and wrench or 10 mm nut driver to

remove the brass orifices from inside the burner base.

Use 10 mm socket and wrench or 10 mm nut driver to install

the new 2.1 mm orifices supplied with this kit.

NOTE: The number 2.1 is stamped on the orifice for

identification.

Repeat the procedure for the other burner.

Replace the burner top and caps. Align the notches in the

bottom of the burner top with the tabs on the burner base

and twist until the burner top is seated on the burner base.

You will feel it drop into the deep notch.

A B

A.Burner top notches

B. Burnerbase tabs

7. Replace the side burner grates.

Change the Sear burner orifices

(for models equipped with sear burner)

1. Remove the sear burner cover screws. Set the screws and

cover aside.

A. Sear burner cover screws

Remove the burner igniter mounting screws.

Loosen the sear burner plate, located next to the igniter.

A. Burner igniter mounting screws

4. Remove the sear burner mounting screws.

A. Sear burner mounting screws

Lift the sear burner out of the grill.

Use 6 mm socket wrench or 6 mm nut driver to remove the

orifice. Install the new 2.34 mm orifice supplied.

NOTE: The number 2.34 is stamped on the orifice for

identification.

7. Reinstall sear burner. Make sure that the igniter is out of the

way to allow proper positioning of burner. Use Phillips

screwdriver to attach the mounting screws.

8. Use Phillips screwdriver to reattach the igniter and sear

burner plate.

9. Reinstall sear burner cover. Use Phillips screwdriver to attach

mounting screws.

Hook up to Natural gas and Leak Test

1. Use pipe wrench to connect certified 1/2"(1.3 cm) gas supply

pipe to inlet side of regulator from Natural gas supply

according to local codes requirements. Use pipe thread

sealant that is certified for use with LP gas at connections

where required. There must be a certified manual shutoff

valve in the gas supply line near the grill for easy access.

2. Turn on the gas supply to the grill.

3. Test all connections using an approved noncorrosive leak-

detection solution. Bubbles will show a leak. Correct any leak

found.

Record Conversion

1. The appliance nameplate is located inside the grill cabinet on

the right-hand cabinet side. With a permanent marker, check

the box next to "Natural gas" and mark through "LP -

Propane."

In the last page of the Use and Care Guide, write "Converted to

Natural Gas." Also record the conversion date and the

technician/company that performed the conversion.

NOTE: Place LP gas parts in plastic parts bag for future use and

keep with pack containing literature.

The burners are tested and factory-set for most efficient 5.

operation. However, variations in gas supply and other conditions

may make minor adjustments to air shutter or low flame setting

necessary.

It is recommended that a qualified person make burner

adjustments.

NOTE: The rotisserie burner cannot be adjusted.

Checking and adjusting the grill burner flames requires removing

the grate and sear plates.

Burner Flame Characteristics

The flames of the grill burners and side burners (on some models)

should be blue and stable with no excessive noise or lifting (LP

gas flames will have a slightly yellow tip). A yellow flame indicates

not enough air. If flame is noisy or lifts away from the burner, there

is too much air. Some yellow tips on flames when the burner is

set to HI setting are acceptable as long as no carbon or soot

deposits appear.

Main burner

Remove the 2 screws that hold the burner in place. Remove

gas burner from the grill.

A.2 screws

If flame is yellow (not enough air), turn air shutter adjustment

screw counterclockwise.

If flame is noisy or lifts away from burner (too much air), turn

air shutter adjustment screw clockwise.

Side burner

A. Burner ports

(1.9 - 2.5 crn)

on all burner ports

with burners on

"Hi" setting

(1.9-2.5cm)

on aH burner ports

with burners on

setting

Check that burners are not blocked by dirt, debris, insect nests,

etc. and clean as necessary. If they are clean, adjust air shutters

as needed.

IMPORTANT: Before adjusting air shutters, let burners cool

completely.

To Adjust:

1. Light grill using information in the "Outdoor Grill Use" section.

2. Observe flame to determine which burners need adjustment

and how the flame is acting.

3. Turn off the valve and wait until grill and burners cool

completely.

4. Remove grill grates and sear plates.

A.Air shutteradjustment screw

Adjustment should be made clockwise or counterclockwise

from V8"(3.2 mm) to V4"(6.4 mm).

Replace gas burner, sear plates and grates.

Light grill using information inthe "Outdoor Grill Use" section.

See "Burner Flame Characteristics."

Low Flame Adjustment

If flame goes out on the "LO" setting, the low flame setting must

be adjusted.

1. Turn off the valve and wait until grill and burners are cool.

2. Remove grill grates and sear plates.

3. Light grill using information in the "Outdoor Grill Use" section.

4. Turn burner to its lowest setting and remove knob.

5. Hold valve stem with pliers and insert a small flat-blade

screwdriver into the shaft.

6. Watch the flame and slowly turn the screwdriver

counterclockwise.

7. Adjust flame to minimum stable flame.

A. Valve stem

B. Small flat-blade screwdriver

C. Pliers

8. Replace the control knob and turn off the burner.

9. Repeat steps 3 through 8 for each burner if needed.

10. Replace the sear plates and grates after the burners have

cooled.

OUTDOOR GRILL USE

This manual covers several different models. The grill you have purchased may have some or all of the features listed. The locations and

appearances of the features shown here may not match those of your model.

Control Panel

A B C D E F G H /

ROTISSERIE LEFT CENTER RIGHT SEAR ROTISSERIE FRONT REAR

BURNER BURNER BURNER BURNER BURNER BURNER BURNER BURNER

A. Left rotisserie burner control knob

B. Left grill burner control knob

C. Center grifl burner control knob

D. Right grill burner control knob

E. Electronic grill display (on some models)

Light switch button (on some models)

F Sear burner control knob

G. Right rotisserie burner control knob

H. Front side burner control knob

I. Rear side burner control knob

ELECTRONIC GRILL DISPLAY

A B

O Fuel Remaining

O Timer

O Flame Time

Time Set Start/Reset

D E F

A. Timer display

B. Mode indicator fights

C. Mode selection button

D. Time set button

E. Start/reset button

F Hood light on/off button

The display will turn on when a gas burner is lit. The display will

default to Fuel Remaining.

This display will also turn on when the Mode, Timer or Start/

Reset button is pushed. The information displayed will be for the

mode of the lit indicator light.

The display area will go blank 10 minutes after the last time that a

button was pushed (except the light button).

If the display does not turn on or if "NP" or "El" is displayed, see

"Troubleshooting" section.

The Start/Reset button starts the Timer and Flame Time TM cycle.

This button also stops and resets these features.

The mode button selects features on the display control.

When the grill is not lit and the Mode button is pushed, it will only

display the information for Modes 1 and 2. The grill must be lit for

Mode 3 to be activated.

Mode I - Fuel Remaining Feature

The fuel remaining feature displays a calculated amount of time

(hours and minutes) the grill can remain lit at the current gas

usage rate before the 201b LP gas fuel tank runs out of fuel.

The Fuel Remaining can be checked when the grill is OFE

check fuel remaining with the grill OFF:

Press Mode button until the indicator light for "Fuel

Remaining" comes on. "00:00" will appear in the display.

After 10 seconds a calculated Fuel Time Remaining will

appear in the display.

To check fuel remaining with the grill burners ON:

1. Press Mode button until the indicator light for "Fuel

Remaining" comes on. "00:00" will appear in the display.

After 10 seconds a calculated Fuel Time Remaining will

appear in the display.

2. The fuel time remaining will be recalculated automatically

7-10 minutes after the grill has been lit.

NOTE: This recalculated display of fuel time remaining may

increase when the grill is used on medium or low settings

because the gas consumption is less.

La page charge ...

KitchenAid KFRU488VSS00 Guide d'installation

Marque: KitchenAid

Modèle: KFRU488VSS00

Catégorie: Barbecues

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KFRU488VSS00 Installation guide

KitchenAid KFRU488VSS00 Guide d'installation

Ce manuel convient également à

KitchenAid KFRU488VSS00 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents