3M DP-10AV Series Manuel utilisateur

User Manual

Innovative LCD Display Solutions

AP

—

10AV Series

DP

—

10AV Series

OP

—

10AV Series

UMUV.10-045V2

Apr 05

P.1

AP-10AV / DP-10AV / DP-10AV Series User Manual

1. Table of Content Page.1

2. Introduction

A) Overview Page.2

B) Features Page.2

C) Dimension Diagrams Page.3-5

D) Technical Specifications Page.6

3. Installation

A) Package Contents Page.7

B) Caution to the user Page.7

C) Cleaning Page.7

D) Precautions Page.8-9

4. Using the System

A) Product Views Page.10-12

B) I/O Outlet Page.13

C) Installation Procedures Page.14

D) Setup Touchscreen (Optional) Page.15

i) For Windows Page.15

ii) For DOS Page.16-18

E) OSD Switch Page.19

F) OSD Control (VGA Version) Page.20-22

G) OSD Control (Video Version) Page.23-27

1. Table of Content

Apr 05

P.2

Disclaimer

This information is subject to change without notice. The producer of this manual accepts no

responsibility for damage or claims, resulting from misuse or misinterpretation

A. Overview

B. Features

AP-10AV / DP-10AV / DP-10AV Series User Manual

2. Introduction

This LCD monitor incorporates 10.4”color active matrix thin-film-transistor

(TFT) liquid crystal display to provide superior display performance. A maxi-

mum resolution of 800 x 600 is ideal for displaying complex graphics and high

definition images. Other outstanding designs that enhance this LCD monitor’s

performance are Plug & Play compatibility and OSD (On Screen Display)

controls.

● High contrast color TFT LCD display support resolution up to 800 x 600.

● Advanced OSD control for picture quality adjustment.

● Detachable stand for wall-mounting application.

● Optional Composite and S-Video input

● Slim and compact size

● Wide Viewing Angle

Apr 05

P.3

AP-10AV series

C. Dimension Diagrams

AP-10AV / DP-10AV / DP-10AV Series User Manual

2. Introduction

Apr 05

P.4

DP-10AV series

C. Dimension Diagrams

AP-10AV / DP-10AV / DP-10AV Series User Manual

2. Introduction

Apr 05

P.5

OP-10AV series

C. Dimension Diagrams

AP-10AV / DP-10AV / DP-10AV Series User Manual

2. Introduction

Apr 05

P.6

Technical Specifications

Monitor

Panel 10.4" LCD Panel

Display Type TFT LCD active matrix colour

Resolutions 800 x 600

Response Time Tr=15ms, Tf=25ms

Contrast Ratio 180:1 typical

Brightness 350 cd/m

2

typical

Pixel Pitch 0.264(H) x 0.264(V)

Panel Colour 262,144 display colour

Viewing Angle 60 / 60 / 55 / 40 (L / R / U / D)

Storage Temp. -20° to 60°C

Operating Temp. 0° to 50°C

MTBF 50,000 hours

Power Supply

Remote Adapter 110V - 220V AC Input

Adapter Size 108(L) x 60 (W) x 30(D) mm

Cable Length from

mains plug to adapter

182cm

Cable Length from

adapter Unit

180cm

Power Socket 12V (+) female

Connectors

RCA Composite video input (female) x 1

S-Video MiniDIN 4-pin (female) x 1

VGA HDDB 15-pin (female) x 1

Video

Standards Supports NTSC, PAL or SECAM

Product

Dimension

AP Series : 275(W) x 215(H) x 51(D) mm

DP Series : 258.5(W) x 198.5(H) x 42.7(D) mm

OP Series : 285(W) x 225(H) x 41(D) mm

Packing

Dimension

AP / DP / OP Series : 480(L) x 362(W) x 85(H) mm

Net / Gross

Weight

AP Series : 2.5 / 4.5 Kg

DP Series : 2 / 4 Kg

OP Series : 2 / 4 Kg

AP-10AV / DP-10AV / DP-10AV Series User Manual

2. Introduction

After unpacking the carton, check and see if the following items are included in

good condition. Contact your supplier as soon as possible for replacing the

missing / damaged items.

● 10.4” TFT LCD monitor

● RCA Cable (Optional For AV Version only)

● S-Video Cable (Optional For AV Version only)

● VGA Cable (Male to Male)

● DC 12V Adapter (5A)

● Power Cord

● Mounting Bracket (AP Series only)

● User Manual

● CD Disc

To assure continued FCC compliance, please use grounded power supply

cord and the provided shielded video interface cable with bonded ferrite cores.

If a BNC cable is going to be used, use only a shielded BNC (5) cable. Also,

The Federal Communications Commission warns the user that any

unauthorized changes or modifications to the unit if not expressly approved by

the party responsible for compliance could void the user's authority of

operating the equipment.

1. Gently wipe screen with a clean camel hair lens brush, or a soft, clean,

lint-free cloth. This removes dust and other particles that can scratch the

screen.

2. Do not apply excessive pressure to the screen surface when wiping it clean

because this may damage the LCD.

3. Do not pour or spray any liquid directly onto the screen or case of the LCD

monitor. Chemical cleaners have been reported to damage the screen or

case of the LCD monitor.

A. Package Contents

Apr 05

P.7

B. Caution to The User

C. Cleaning

AP-10AV / DP-10AV / DP-10AV Series User Manual

3. Installation

Apr 05

P.8

Read all of these instructions and save them for later use. Follow all warnings

and instructions on the product.

Product

● Do not cover or block the vent holes in the case.

● Do not insert sharp objects or spill liquid into the LCD monitor through

cabinet slots. They may cause accident fire, electric shock or failure.

● Disconnect the power plug from the AC outlet if you will not use it for an

indefinite period of time.

● Do not attempt to service this product yourself, as opening or removing

covers may expose you to dangerous voltage points or other risks.

● Do not touch the screen directly with your fingers. You may damage the

screen, and oil from your skin in difficult to move.

● Do not apply pressure to screen. The LCD is very delicate.

D. Precautions

Power

1. Use the type of power indicated on the marking label.

Plugs

1. Do not remove any of the prongs of the monitor’s three-pronged power

plug.

2. Disconnect the power plug from the AC outlet under following

conditions ：

● If the product will not be used for an indefinite period time.

● When the power cord or plug is damaged or frayed.

● If the product does not operate normally when the operating

instructions are followed.

● Adjust only those controls that are covered by the operating

instructions. Improper adjustment of other controls may result in

damage and will often require extensive work by a qualified

technician to restore the product to normal operation.

● If the product has been dropped or the cabinet has been damaged.

● If the product exhibits a distinct change in performance, indicating a

need for service.

AP-10AV / DP-10AV / DP-10AV Series User Manual

3. Installation

Apr 05

P.9

D. Precautions (Cont.)

Power and extension cords

1. Do not allow anything to rest on the power cord.

2. Do not locate this product where persons will walk on the cord.

3. Use the proper power cord with correct attachment plug type. If the

power source is 120V AC, use a power cord that has UL and C-UL

approvals. If the power source is a 240V AC supply, use the tandem

(T blade) type attachment plug with ground conductor power cord that

meets the respective European country’s safety regulations, such as

VDE for Germany.

4. Do not overload wall outlets or power cords. Ensure that the total of all

units plugged into the wall outlet does not exceed 10 amperes.

5. Ensure that the total ampere ratings on all units plugged into the

extension cord is not above the cord’s rating.

6. If the power supply cord, which came with your monitor, is to be

connected to the PC instead of the wall outlet, this equipment is to be

used with UL/TÜV approved computers with receptacle rated

100~240V AC, 50/60Hz, 1.0A(minimum).

Environment

1. Place the monitor on a flat and leveled surface.

2. Place the monitor in a well-ventilated place.

3. Keep the monitor away from： Overly hot, cold or humid places, places

directly under sunlight, dusty surroundings, equipment that generate

strong magnetic fields.

AP-10AV / DP-10AV / DP-10AV Series User Manual

3. Installation

A. Product Views

AP Series - Front View

AP Series - Rear View

AP-10AV / DP-10AV / DP-10AV Series User Manual

Apr 05

P.10

3. Installation

A. Product Views (Cont.)

DP Series - Front View

DP Series - Rear View

AP-10AV / DP-10AV / DP-10AV Series User Manual

Apr 05

P.11

3. Installation

A. Product Views (Cont.)

OP Series - Front View

OP Series - Rear View

AP-10AV / DP-10AV / DP-10AV Series User Manual

Apr 05

P.12

3. Installation

Apr 05

P.13

B. I/O Outlet

AP-10AV / DP-10AV / DP-10AV Series User Manual

4. Using the System

AP Series

DP Series

OP Series

1. DC IN ： Connect to DC power cable.

2. PC IN ： Connect to D-Sub 15 pin signal connector.

3. RCA IN ： Connect to the composite cable connector. (for AV series only)

4. S-Video IN ： Connect to the S-Video cable connector. (for AV series only)

5. USB IN ： Connect to the USB connector. (for Touchscreen series only)

6. SERIAL IN ： Connect to the Serial connector. (for Touchscreen series only)

(1)

(2)

(3)

(4)

(5)

(6)

Apr 05

P.14

C. Installation Procedures

This monitor is equipped with an auto-sensing power supply for

voltage ranges 100~240V, 50~60Hz. Please follow the following

instruction to install LCD monitor.

1. Make sure that the system power is turned off.

2. Plug the signal cable to the signal connector at the rear of

PC and the rear of the LCD monitor.

3. Plug adapter output cable to the jack at the rear of LCD

monitor and the power cord to the adapter.

4. Connect the power cord to power source.

5. Turn on the computer and the monitor.

6. Then push the OSD menu button and use the Auto Adjust

function to fine the best mode of your computer.

AP-10AV / DP-10AV / DP-10AV Series User Manual

4. Using the System

D. Setup Touchscreen

Touchscreen used for UltraView products are manufactured by 3M. Here provide

TouchWare

TM

Software includes touch screen drivers for your installing.

For Windows 95, 98, Me, NT4.0, 2000 & XP

1. Open the driver CD provided along with the product or download the driver

from our Website.

2. Make sure you have completed the appropriate hardware connections.

3. Power on your system. Make sure no other application are opened.

4. Double click the “TW564SR4.exe” files.

5. Unzip the file and save it in a default folder

6. Follow the onscreen instructions to begin the installation.

Apr 05

P.15

Note: Choose Express option for automatically installs the required TouchWare

TM

software files, create a TouchWare

TM

software program files, and place a

TouchWare

TM

software icon on the Windows desktop and control panel.

TouchWare

TM

will also determine multiple monitor configurations at this time.

Note: Remember the path of the default folder or create a new folder by your decision.

Note: For details of Custom option, please refer to the website of 3M and download the

user guide of TouchWare

TM

software.

(http:// www.3m.com/3MTouchSystems/downloads/tecdoc.jhtml)

Note: If you have a Microsoft® IntelliPoint® or Kensington® Mousework® PS/2

mouse, installing TouchWare

TM

software will disable the special mouse

functionally of these devices

AP-10AV / DP-10AV / DP-10AV Series User Manual

Note: To configure the settings of the touchscreen, please refer to the

TouchWare

TM

User Guideline

4. Using the System

D. Setup Touchscreen

For Windows 95, 98, Me, NT4.0, 2000 & XP (Cont.)

7. Once installation is complete, restart the system. As the system restarts,

Windows detects and loads the driver.

● For serial controllers, restart the system. As the system restarts, Win-

dows detects and load the driver

● For USB controllers, connect the touch screen cable to the USB port in

your computer. After a few seconds, the system beeps to indicate it has

detected the touch screen and loaded the driver.

For DOS

When you install Touchware from DOS, the Install program only loads the

touchscreen files specific to DOS. The installation includes the following files:

● Touchscreen driver for DOS

● Touchscreen control panel for DOS

● Pen Configuration utility for DOS

● Microcal Diagnostic utility

● ThruGlass control panel for DOS

● DOS help files

If you do not plan to use any of the touchscreen files for windows, you may want

to install just the DOS touchscreen files.

1. Open the driver CD provided along with the product or download the driver

from our Website.

2. Make sure you have completed the appropriate hardware connections. If

not, the Install program cannot properly configure the touchscreen.

3. Close all applications and exit from Windows.

4. Insert the TouchWare Disk into a diskette drive.

5. Access the DOS command line prompt.

6. Change to the drive that has the TouchWare diskette. For example, enter A:

if you inserted the TouchWare diskette in Drive A.

Note: This step is not necessary for Windows 2000 or above system, The driver loads

automatically.

AP-10AV / DP-10AV / DP-10AV Series User Manual

4. Using the System

Apr 05

P.16

Apr 05

P.17

D. Setup Touchscreen

For DOS (Cont.)

7. Type INSTALL followed by the source disk drive, the destination drive, and

the destination directory.

For example, the following command copies the files from Drive A (source

drive) to Drive C (destination drive) and the \MTS\TOUCH directory :

INSTALL A: C:\MTS\TOUCH

8. Press Enter. The system reports that it is about to copy the DOS touchscreen

files and prompt for confirmation that you want to continue.

9. Press C to start the installation.

● First, the Install program copies all DOS touchscreen files from the

TouchWare diskette to the specified destination drive and directory.

● Next, the Install program automatically searched through the system

and configures the touchscreen to the proper COM port, interrupt, and

communication rate.

● Finally, the Install program prompts if you want it to automatically modify

your AUTOEXEC.BAT file

If you let the Install program modify your AUTOEXEC.BAT file, the system

automatically loads the DOS touchscreen driver whenever you start your

computer.

If you do not let the Install program modify your AUTOEXEC.BAT file, you

must load the DOS touchscreen driver before using a DOS touch application.

For more information, refer to “Loading the DOS Touchscreen Driver” in the

4. Using the System

D. Setup Touchscreen

For DOS (Cont.)

Loading the DOS Touchscreen Driver

After you install the files for the DOS touchscreen driver, you must load the driver

before you can run a DOS touch application or open the DOS Touchscreen

control panel.

You can run the DOS touchscreen driver from a full-screen DOS session within

Windows. However, the Windows touchscreen driver cannot be running. Error

message reads: “Windows x.x is running in 386 Enhanced mode. Device not

found.”

This means either the Windows Touchscreen driver is loaded or the COM port/

IRQ designations are incorrect.

You can manually load the DOS touchscreen driver when needed, or you can let

the system automatically load the driver when you start up your computer.

● To manually load the DOS touchscreen driver:

1. Close all applications and exit from Windows.

2. Access the DOS command line prompt.

3. Use the Change Directory (cd) command to switch to the directory that

has the DOS touch driver files. By default, the Install program loads

TouchWare into the C:\MTS|TOUCH directory.

4. Type DOSTOUCH and then press Enter. The system displays a message

that the driver is now installed. For example:

MicroTouch Mouse Emulator - Version x.x

Driver Installed

● To automatically load the DOS touchscreen driver when you start up your

computer, add the following line to your AUTOEXEC.BAT file :

drive-designator :\directory\DOSTOUCH

where drive-designator and directory define the location (disk and path) of

the files for the DOS touchscreen. For example:

AP-10AV / DP-10AV / DP-10AV Series User Manual

4. Using the System

Apr 05

P.18

Apr 05

P.19

E. OSD Switch

Input Select: This button is used to select CVBS for composite

video input, RGB for VGA input and S-Video for

Super-Video input

OSD Menu: This button is used to enter OSD main Menu

Increase(à): This button is used to adjust the increasing or

next value of selected OSD control option.

Decrease(ß): This button is used to adjust the decreasing or

next value of selected OSD control option.

Power Switch: This button is used to power ON/OFF the LCD

AP-10AV / DP-10AV / DP-10AV Series User Manual

4. Using the System

Left

Right

Exit

Menu/Selection Power

La page charge ...

3M DP-10AV Series Manuel utilisateur

Ce manuel convient également à

3M DP-10AV Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents